Answer:
585×10⁸ m
Explanation:
Distance = rate × time
d = (2.998×10⁸ m/s) (3.25 min) (60 s/min)
d = 585×10⁸ m
Six members of a synchronized swim team wear earplugs to protect themselves against water pressure at depths, but they can still hear the music and perform the combinations in the water perfectly. One day, they were asked to leave the pool so the dive team could practice a few dives, and they tried to practice on a mat, but seemed to have a lot more difficulty. Why might this be
Answer:
The sound travels differently in different medium according the density of the medium.
Explanation:
The sound travels faster in dense medium and can be heard by the vibration of the bone present in the ear. The ear plugs reduce the sound intensity in both medium water and on land (air).
In air the sound is not heard properly due to the earplugs that stops the as the vibration are not able to produce as sound is not able to reach to middle ear, but Navy researchers have discovered that sound under water is heard by the bone present behind the ear, vibrations mastoid.
what is the best defintion of efficency
Answer: Efficiency signifies a peak level of performance that uses the least amount of inputs to achieve the highest amount of output.
Explanation: It minimizes the waste of resources such as physical materials, energy, and time while accomplishing the desired output.
Answer:
The efficiency of a simple machine is defined as the ratio of useful work done by the machine ( output work) to the total work out into the machine ( input work).
Explanation:
EfficiencyIf a machine overcomes a load ' L ' and the distance travelled by the load is 'Ld' , the work done by the load is L× LD. It is also called output work or useful work.
Therefore, [tex] \boxed{Output \: work \: = L \: \times \: Ld}[/tex]
Likewise, The effort applied to overcome the load is 'E' and the distance covered by effort is 'Ed' , the work done by effort is E × Ed. It is also called input work.
Therefore, [tex] \boxed{Input \: work = E \times Ed}[/tex]
The efficiency of a simple machine is defined as the ratio of output work to the input work .
Therefore, [tex] \boxed{Efficiency ( η)= \frac{outpt \: work}{input \: work} \times 100\%}[/tex]
Efficiency is expressed in percentage. It is a ratio of two works. A machine is never 100% efficient. It is because no machine is friction free and due to friction, some of the input energy is wastes in the form of heat energy.
[tex] \mathrm{Hope \: I \: helped!}[/tex]
[tex] \mathrm{Best \: regards!}[/tex]
You are the driver of the car in the photos above. You Are traveling at 30 mph when suddenly the car goes from its position in the first photo to the position in the second photo. What is happening
Answer:
the car uses teleportation, to zip to one side of the photo, to the other
Explanation:
the unit of energy is a derived unit
Explanation:
Hi, there!!
Energy is defined as the capacity or ability to do work. It's SI unit is Joule.
here,
Joule = (kg×m×m)/(s×s)
= kg×m^2/s^2.
Therefore, the derived unit is kg.m^2 by s^2.
Hope it helps...
Please give best dialogue in photo that is attached And you are marked as Brainliest
Answer:
The correct answer is
Explanation:
Character 1: Why are these comic books so hard to read? Can u read them?
Character 2: No it's easy to read Tigger. It's because you are an animal an I am a human being. U don't know how to read.
Hope this helps....
Have a nice day!!!!
Answer:
Dialogue 1:
Hey buddy! Can you tell me what is written in this book? Its really hard to read:(
Dialogue 2:
Yeah! Its a story about a friendly tiger! And it is hard for you to read cause you don't know how to read.
Tip:
Try to make it more engaging :)
Dennis throws a volleyball up in the air. It reaches its maximum height 1.1\, \text s1.1s1, point, 1, start text, s, end text later. We can ignore air resistance. What was the volleyball's velocity at the moment it was tossed into the air?
Answer:
If max height = 1.1 meters, then initial velocity is 3.28 m/s
If max height is 1.1 feet, then the initial velocity is 5.93 ft/s
Explanation:
Recall the formulas for vertical motion under the acceleration of gravity;
for the vertical velocity of the object we have
[tex]v=v_0-g \,t[/tex]
for the object's vertical displacement we have
[tex]y-y_0=v_0\,t - \frac{g}{2} \,t^2[/tex]
If the maximum height reached by the object is given in meters, we use the value for g in [tex]m/s^2[/tex] which is: [tex]9.8\,\,m/s^2[/tex]
If the maximum height of the object is given in feet, we use the value for g in [tex]ft/s^2[/tex] which is : [tex]32\,\,ft/s^2[/tex]
Now, when the ball reaches its maximum height, the ball's velocity is zero, so that allows us to solve for the time (t) the process of reaching the max height takes:
[tex]v=v_0-g \,t\\0=v_0-g \,t\\g\,\,t=v_0\\t=\frac{v_0}{g}[/tex]
and now we use this to express the maximum height in the second equation we typed:
[tex]y-y_0=v_0\,t - \frac{g}{2} \,t^2\\max\,height=v_0\,(\frac{v_0}{g}) - \frac{g}{2} \,(\frac{v_0}{g})^2\\max\,height= \frac{v_0^2}{2\,g}[/tex]
Then if the max height is 1.1 meters, we use the following formula to solve for [tex]v_0[/tex]:
[tex]1.1= \frac{v_0^2}{2\,9.8}\\(9.8)\,(1.1)=v_0^2\\v_0=10.78\\v_0=\sqrt{10.78} \\v_0=3.28\,\,m/s[/tex]
If the max height is 1.1 feet, we use the following formula to solve for [tex]v_0[/tex]:
[tex]1.1= \frac{v_0^2}{2\,32}\\(32)\,(1.1)=v_0^2\\v_0=35.2\\v_0=\sqrt{35.2} \\v_0=5.93\,\,ft/s[/tex]
Answer:
11
Explanation:
for khan academy, this is the answer
please help ASAP.
these are examination questions ..
no nonsense answers .
i will mark as brainliest if you got it correct .
Answer:
1st question c part
2nd question c part
Astronomers were at first surprised to find complicated molecules in the interstellar medium. They thought ultra-violet light from stars would break apart such molecules. What protects the molecules we observe from being broken apart
Answer:
The dust present in the clouds.
Explanation:
The complicated composition molecules that can be found in space are generally associated with clouds of dust. The significant amount of dust in these clouds provides protection not only for these molecules, but for any body that makes up or is associated with dust clouds.
It is exactly this dust that protects the molecules against the action of ultraviolet rays.
A physical inventory on December 31 shows 3500 units on hand. Bonita sells the units for $15 each. The company has an effective tax rate of 20%. Bonita uses the periodic inventory method. The weighted-average cost per unit is
if a direction is somewhere between North and East it is measured in _____?
Answer:
degrees
Explanation:
If a direction is somewhere between north and east, it is measured in degrees.
This measurement will be possible thanks to the existence of geographical coordinates that are some 'imaginary lines' that help us find our location on the earth's surface. These lines are called latitude and longitude, both of which are measured in degrees.
It is like a sea battle game where you have to combine the rows and columns in order to identify where the targets are located. Geographic coordinates work the same way, you must combine the rows and columns of the planisphere to identify the locations of the planet. So the lines would be the latitudes and the columns the longitudes.
Which of the following illustrates an increase in potential energy? Group of answer choices a wind-up toy winding down a person climbs a set of stairs an apple dropping from a tree a firecracker explodes
Answer:
A person climbs a set of stairs
Explanation:
Potential energy is said to be possessed by an object due to its position. As the height from the ground level increase, the potential energy increases. It is calculated by the below formula as :
P = mgh
Out of the given options, the option that illustrates an increase in potential energy is option (b) i.e. a person climbs a set of stairs. As he steps one stair, its position from ground increases. It means its potential energy increases.
fill in the blanks
1.)Seed drill is used for ____ of the seeds.
2.)ploughing helps the_____of roots of the growing plants.
3.)Tilling of the soil is also called a ________.
4.)Manure and fertilizers are use ti maintain the______of the soil.
5.)A most common weedicide is________.
6.)After harvesting,grains are separated from the chaffand hay by _______ or by using ______.
7.)The economial methods of irrigation are_____and____.
8.)The wild plants which grow along with the main crop are called_________.
9.) Shifting of tiny plants from a nursery to the main field is called______.
10.) Excess water and wet soil do not permit proper_____of the seeds or roots of the plants.
Answer:
1.) Sowing
2.) Respiration
3.) Soil preparation or cultivation or ploughing
4.) Fertility
5.) 2, 4 -D
6.) winnowing threshers
7.) Surface irrigation and sprinkler irrigation
8.) Weeds
9.) Transplantation
10.) Aeration
Explanation:
1.) Seed drill sows crop seed
2.) Ploughing assist in the respiration and penetration of the roots of a growing plants
3.) Tilling the soil is breaking of the soil lumps and turning of the soil
4.) Manure and fertilizers supply nutrient to the soil for the uptake by plant in food production
5.) 2, 4 -D are a range of weedicide containing 2,4-D as the active ingredient
6.) Winnowing is the separation of grain from straw
Threshers remove seeds from husks and stalks
7.) Surface irrigation -gravity enables the flow of the water
and sprinkler irrigation- Use of preset tools for irrigation
8.) Weeds are the unwanted, in situ, growing plants close to the crops
9.) Transplantation is the method of relocating plants
10.) Excess water limits access of the roots and seeds to atmospheric oxygen
Jaiden is writing a report about the structure of the atom in her report,she says that the atom has three main parts and two subatomic particles. Do you agree with her?why or why not
Answer:
I do not agree with the answer.
Because in reality, the atom has 2 main parts and 3 subatomic particles.
Explanation:
The parts of an atom are:
- The crust: It is the outer part of the atom and is the place where the electrons are.
- The nucleus: It is the central part of the atom and is the place that contains the protons and neutrons.
The subatomic particles of the atom are:
- Electrons: They are negatively charged particles that go in the atom's crust and are divided into specific sections.
- Protons: They are particles with a positive electric charge, the number of protons in the nucleus of an atom is what determines the atomic number of an element.
- Neutrons: They are atoms with no electric charge.
how do you find average velocity
Answer:
find the sum of the inital and final velocitys and divide by 2 to find the average
If you look at faint stars, you can see them more easily on the edges of your vision than if you try to look directly at them. Why is this true?
Answer:
The retina comprises of rod and cone cells . The rod cells are responsible for black and white vision and require low light levels while the cone cells are responsible for color vision and require good/high light levels for better functioning.
When faint stars are looked at on the edges of the vision it allows more light from faint objects to strike the rod cells which then becomes more visible.
A 970-kg sports car collides into the rear end of a 2300-kg SUV stopped at a red light. The bumpers lock, the brakes are locked, and the two cars skid forward 2.9 m before stopping. The police officer, estimating the coefficient of kinetic friction between tires and road to be 0.80, calculates the speed of the sports car at impact.
Answer:
22.73 m/s or 81.72 kph
Explanation
We can find the combined mass of both cars as
970 kg + 2300 kg = 3270 kg.
Then the normal force of the cars can be calculated as
F(n)= mg
Where g is acceleration due to gravity 9.8m/s^2
3270 kg ×9.8 = 32046 kg*m/s^2.
coefficient of kinetic friction between tires and road to be 0.80 × F(n)
Then the frictional force can be calculated as
= (32046kg*m/s^2 × 0.80 )
= 25636.8 kg*m/s^2
We can now calculate the work done that was used stopping the cars as
Frictional force × distance
(25636.8 kg*m/s^2 ) × 2.9m= 74346.72kg*m^2/s^2
From kinetic energy formula, the combined velocity of the car can be determined
E=0.5 M V²
√(2E/M) = V
√(2*74346.72kg*m^2/s^2 / 3270 kg) = V
V= √ (45.472)
V=6.743293m/s
the momentum of both cars can be determined as
6.743293m/s * 3270 kg
= 22050.57kg*m/s
Now the final momentum of both cars must be equal to the the momentum of
the sports car just prior to the collision. Therefore, the speed of the sports car at impact.
=(22050.57 kg*m/s) / 970 kg = 22.73 m/s
We can convert that to km/h.
22.73 m/s * 3600 s/h / 1000 m/km = 81.72 kph
A space rocket accelerates uniformly from rest to 160ms^-1 upwards in 4.0s, then travels with a constant speed of 160ms^-1 for the next 5.0s.
What is the initial acceleration of the rocket?
Answer:
40 ms¯².
Explanation:
To solve this problem, we shall illustrate the question with a diagram.
The attached photo gives a better understanding of the question.
From the attached photo:
Velocity (v) = 160 ms¯¹
Time (t) = 4 secs.
Acceleration (a) =?
Acceleration (a) = Velocity (v) /time (t)
a = v/t
a = 160/4
a = 40 ms¯²
Therefore, the initial acceleration of the rocket is 40 ms¯².
Help!!! Line B touches the circle at a single point. Line A extends through the center of the circle.
I. What is line b in reference to the circle?
2. How large is the angle between lines A and B?
Answer:
If I understand correctly. Line B is parallel to the circle. Also, the angle is less than 90.
The size of the circle determines. The diameter should not be fixed either.'Circle' is characterized as "a two-dimensional geometric figure comprising of the set of all those points in a plane that are at equal distance from the center."
1). Line B would be considered as the 'tangent' in association with the given circle.
2). The angle lying among the lines A and B would be of 90° i.e. right angle.
Given that,
A circle with line A drawn through its center
Line B moves while touching the edge of the circle and intersects line A outside the circle.
Since 'Tangent' is described as a 'straight-line touching the curve at one point without crossing it,' thus, line B would be considered as the tangent of the circle as it touches the circle's curve once. The angle that is formed at the intersection of the line A and B at the curve of the circle would be a right angle because they are perpendicular to one another. Thus, the perpendicular lines A and B form an angle of 90°.Learn more about 'circle' here:
brainly.com/question/11833983
Match the following:
Tailored software
. Utility software
Operating system
Software
Packaged software
Set of programs
Library management system
Scan viruses
Microsoft Office
used to coordinate the hardw
the computer
Answer:
1) Tailored software Library management system
2) Utility software Scan viruses
3) Operating system Used to coordinate the hardware of the computer
4) Packaged software set of programs Microsoft office
Explanation:
1) A tailored software, also known as a custom software, is one that is designed and tailor-made only for a particular organisation
2) A utility software is a computer maintenance and analysis software used to enable proper functioning of the computer by performing restorative and maintenance tasks
3) Operating system software
The operating system software controls the operation of the computer hardware within the system and enables the operation of other programs in the computer
4) Packaged software are a collection of programs that are oriented to perform interrelated tasks that a focused to a particular area, such as Microsoft Office.
You have a hot reservoir held at 30°C and a cold reservoir held at 0°C. If you move 400 J of heat from the hot reservoir to the cold reservoir, what is the total change in entropy?
Answer:
Explanation:
Given the following :
Temperature (Th) of hot reservoir = 30°C (30 +273) = 303K
Temperature (Tc) of cold reservoir = 0°C (273K)
Quantity (Q) of heat transferred from hot reservoir = 400 J
Total change in entropy (ΔStotal) :
ΔStotal = ΔShot + ΔScold
ΔS = Q/T
Hot reservoir is losing 400J of heat ;
Q = - 400 J
ΔShot = Q/Th
ΔShot = - 400/303
ΔShot = - 1.32 J/K
ΔScold = Q/T
ΔScold = 400 / 273
ΔScold = 1.47 J/K
ΔStotal = ΔShot + ΔScold
ΔStotal = - 1.32 + 1.47
ΔS total = 0.15 J/K
Answer:
-400/303 = -1.32
400/273 = 1.47
-1.32 + 1.47 =
.15 J/K
Explanation:
a p e x
Suppose that you have been chosen for a space mission to a distant planet. Due to the length of time you'll be away from Earth you must carry out physical activity every day. On earth your, strength and conditioning trainer has determined you must do 90 minutes of exercise every day. If the vehicle is travelling at 0.80 c how much time, according to a timer on the space vehicle should you be active to meet your physical activity requirement?
Answer:
I should be active for 15 hours to meet the physical activity requirement.
Explanation:
Since time dilates in moving objects, we use the formula t = t₀/√(1 - β²) where t = time in space vehicle, t₀ = time on earth = 9 hours and β = v/c where v = speed of space vehicle = 0.8c.
So, t = t₀/√(1 - β²)
t = 9/√(1 - (v/c)²)
= 9/√(1 - (0.8c/c)²)
= 9/√(1 - (0.8)²)
= 9/√(1 - (0.64)
= 9/√0.36
= 9/0.6
= 15 hr
So, according to a timer on the space vehicle, I should be active for 15 hours to meet the physical activity requirement.
Question is on the picture. Answers: A. 0.1 J/g*C B. 0.2 J/g*C C. 0.4 J/g*C D. 4 J/g*C
Answer:
B. 0.2 J/g/°C
Explanation:
The solid phase is the first segment (from 0°C to 50°C).
q = mCΔT
200 J = (20 g) C (50°C)
C = 0.2 J/g/°C
i) A 100 W and 60 W bulb are joined in series and connected to the mains. Which bulb
will glow brighter? Why?
ii) A 100 W and a 60 W bulb are joined in parallel to the mains. Which bulb will
glow brighter? Why?
Answer:
i) 60 W
ii) 100 W
Explanation:
In each case, the bulb that dissipates the most power is the bulb that glows brighter. Power is voltage times current (P = VI). Using Ohm's law, we can rewrite this as P = I²R or P = V²/R.
Bulbs are rated at a certain power for a certain voltage. P = V²/R, so the bulb with the lower resistance will have the higher power rating. Therefore, the 100 W bulb has a lower resistance than the 60 W bulb.
i) They are in series, so they have the same current. P = I²R, so the bulb with the higher resistance will glow brighter. That's the 60 W bulb.
ii) They are in parallel, so they have the same voltage. P = V²/R, so the bulb with the lower resistance will glow brighter. That's the 100 W bulb.
explore how archemides principle is applied in building a ship and submarine
Answer:
Principle Archimedes is applied in building a ship and submarine using the manipulating that buoyancy, is controlled the ballast tank system.
Explanation:
Submarine is rather had they focused on main parts of the submarine,he is complex and long process implementation,the most submarine design like submarine stability.
Submarine stability is complete and the fundamental Archimedes principle to arrive the weight of submarine is equal to buoyancy force.
Submarine into the parts and components of ballast tank the sequence in diving and surfacing,there two vital parts:- flood parts and air vents
flood parts:- at the bottom position and allow water to enter or leave that tank.
air vents:- air vents at the top of the pressure hall,and that they submarine dive.
this time submarine is most modern system is depth is 300 to 450 meters,high pressure air is 15 bar is tank air valve.
submarine is basic of the effective volume of all the submarine surfaced condition,submarine minus to the free water flood is equal to the fully pressure hull,submarine is the surfaced condition.
calculate the power of an engine which can supply 60kg of energy per minute
Answer:
1 Watt
Explanation:
Power (P) = w / Δt
w = work done
Δt = change in time
Power (P) = 60kg / 60 seconds
Power (P) = 1 Watt
Un pez llamado PARGO ROJO vive a grandes profundidades. Si se pesca, al salir a la superficie puede tomar el aspecto de la foto porque su vejiga natatoria aumenta de volumen al disminuir la presión. La ley que lo explica es...
Answer:
Hay diversas leyes que podemos usar acá.
Acá sabemos que la vejiga aumenta su tamaño al reducir la presión, esto tiene sentido, pues al haber menos presión, hay menos fuerza que comprime la vejiga, lo que le permite aumentar su volumen.
Acá tenemos una relación inversa de la forma: V = K/P
Una relación inversa donde la presión esta en el denominador y K es un termino que no depende ni del volumen ni de la presión.
Entonces, a medida que aumenta P, el denominador aumenta, por lo que el valor del volumen decrece.
Un ejemplo de una ecuación similar es la del gas ideal, por ejemplo, para un gas ideal dentro de un globo de volumen V para una dada presión P:
V = nRT/P
donde n es el numero de moles, R es la constante termodinámica y T es la temperatura, acá podemos ver que esta ecuación tiene la misma forma fundamental que la escrita arriba.
You are hiking in a canyon and you notice an echo. You decide to let out a yell and notice it took 2 seconds before you heard the echo of your yell. How far away is the canyon wall that reflected your yell
Answer:
d = 343 m
Explanation:
Given that,
You notice that an echo took 2 seconds before you heard the echo of your yell.
We need to find that how far away is the canyon wall that reflected your yell. It means we need to find the distance.
The distance covered by an object is given by :
d = v × t
v is speed of sound in air, v = 343 m/s
The sound took 1 s to reach the wall and 1 s back to you.
It means that,
d = 343 × 1
d = 343 m
So, canyon will reflect your yell at a distance of 343 m
The length and breadth of rectangular sheet of metal are 4.234m, 1.005,
and 2.01cm respectively.
Give the area and volume of sheet to correct significant figures..
Answer:
The area of the sheet of metal = 4.255 m²
The volume of the sheet of metal = 0.08553 m³
Explanation:
The area of a rectangle is given by the following relation;
Area, A = Length × Breadth
Therefore, the area of the rectangular sheet of metal, A[tex]_m[/tex], is given as follows;
A[tex]_m[/tex] = 4.234 m × 1.005 m = 4.255 m²
The area of the sheet of metal = 4.255 m²
The volume of the metal sheet id given by the relation, volume V[tex]_m[/tex]= area × Thickness
The thickness of the sheet of metal = 2.01 cm = 0.0201 m
Therefore,
V[tex]_m[/tex] = 4.255 m × 0.0201 m = 0.08553 m³
The volume of the sheet of metal = 0.08553 m³.
Answer:
Are yarr mei bhi Indian hu.....
Explanation:
Tumse milkar accha laga
A magnet pulls a piece of iron with a force of 1 N. What is the force that the iron piece exerts on the magnet?
The iron piece exerts a force of 1 N divided by the ratio of the weight of the iron piece to the weight of the magnet in the same direction.
The iron piece exerts a force of 1 N on the magnet in the opposite direction.
The iron piece exerts a force of 1 N divided by the ratio of the weight of the iron piece to the weight of the magnet in the opposite direction.
The iron piece exerts a force of 1 N on the magnet in the same direction.
Answer:
the final statements the correct one is. The second
The iron piece exerts a force of 1 N on the magnet in the opposite direction
Explanation:
In this exercise they give us the force exerted by a magnet on an iron bar and ask us the force that the iron bar exerts on the magnet. We can see that these are action and reaction forces, which by Newton's third law must be of equal magnitude and opposite direction, each applied to one of the bodies.
the final statements the correct one is. The second
The iron piece exerts a force of 1 N on the magnet in the opposite direction
Which term describes the ability to process many things simultaneously?
O Effortful processing
O Parallel processing
O Mood congruent memory
O Flashbulb memory
O Working memory
Answer:
Parallel processing
Explanation:
It is a parallel processing because it involves the brain processing many part of problem simultaneously.
The brain natural mode of information involves performing many task .
It is also ability of the brain to simultaneously process incoming stimuli or signals of different quality. It is a part of brain's vision and divide what is seen into four major parts which are color, motion, shape, and depth.
Answer: B) Parallel processing
