In some cases, neither of the two equations in the system will contain a variable with a coefficient of 1, so we must take a further step to isolate it. Let's say we now have
3C+4D=5
2C+5D=2
None of these terms has a coefficient of 1. Instead, we'll pick the variable with the smallest coefficient and isolate it. Move the term with the lowest coefficient so that it's alone on one side of its equation, then divide by the coefficient. Which of the following expressions would result from that process?
Now that you have one of the two variables in Part D isolated, use substitution to solve for the two variables. You may want to review the Multiplication and Division of Fractions and Simplifying an Expression Primers.

Answer:

[tex]Vm=0.894m/s[/tex]

Explanation:

From the question we are told that

Velocity if travel [tex]v=4m/s[/tex]

Diameter of  prototype [tex]d_1=20m[/tex] and [tex]d_2=110m[/tex]

Scale ratio=[tex]\frac{1}{20}[/tex]

Generally Velocity of of the model using Froud's model is mathematically given as

[tex]Fm=Fp[/tex]

[tex]\frac{Vm}{\sqrt{Lmg}} =\frac{Vp}{\sqrt{Lpg}}[/tex]

[tex]Vm=Vp*\frac{Vp}{\sqrt{Lpg} }[/tex]

[tex]Vm=4*\frac{1}{\sqrt{20}}[/tex]

[tex]Vm=0.894m/s[/tex]

Non-Malleable and Ductile: Non-metals are very brittle, and cannot be rolled into wires or pounded into sheets. Conduction: They are poor conductors of heat and electricity. Luster: These have no metallic luster and do not reflect light.

Group 15, the nitrogen family, contains two nonmetals: nitrogen and phosphorus. These non-metals usually gain or share three electrons when reacting with atoms of other elements. Group 16, the oxygen family, contains three nonmetals: oxygen, sulfur, and selenium.

Elements: Nitrogen; Oxygen; Phosphorus; Selenium...

Answer:

Because there was fewer fossils

Explanation:

Answer:

Actually the answer is "The stratum contains iridium.".

Explanation:

Answer:

58.8J

Explanation:

Given parameters;

Mass of ball  = 4kg

Height above the floor  = 1.5m

g  = 9.8n/kg

Unknown:

Potential energy  = ?

Solution:

The potential energy of a body is the energy due to the position of the body.

It is mathematically expressed as:

  Potential energy = mass x acceleration due to gravity x height

  Potential energy  = 4 x 9.8 x 1.5  = 58.8J

Answer:

Chemical energy

Explanation:

The energy in the torch is stored as chemical energy before the torch gets switch on.

The chemical energy energy in the battery of cell will power the cell and allows it to produce light.

Answer:

C. Is traveling on a curve in the road

    Hope this helps :3

The pick up truck has a changing velocity because, it is travelling on a curve in the road. A change in direction results in its change in velocity because, velocity is a vector quantity.

Velocity is a physical quantity that measures the distance covered by an object per unit time. It is a vector quantity, thus having magnitude as well direction.

The rate of change in velocity is called acceleration of the object. Like velocity, acceleration also is a vector quantity. Thus, a change in magnitude or direction or change in both for velocity make the object to accelerate.

Here, all the three vehicles  are travelling with the same velocity. But, the truck is moving to a curve on the road. The curvature in the path will make a change in its velocity.

Find more on velocity:

https://brainly.com/question/16379705

#SPJ6

The image related with this question is attached below:

Answer:

A

Explanation:

Ke = 1/2 MV^2

Answer:

ieces A and B must also have the same type of charges

Explanation:

In electrostatics, charges of the same sign repel and charges of different signs attract.

If we apply this to our case, we have that part A and C repel each other, therefore they have the same type of charge.

Also part A and C repel each other, therefore they have the same type of charge.

If we use the transitive property of mathematics, pieces A and B must also have the same type of charges

Answer:

C) 128 kg*m/s

Explanation:

When you double something you multiply it by 2 most of the time. 64*2=128 or you can add it 64+64=128. Hope this helps.

Explanation:

False, it is oppisite the shorter the wavelength the more energy it carries.

Answer:

the correct one is the first,   the refractive index of the two materials must be the same

Explanation:

When a beam of light passes through two materials, it must comply with the law of refraction

         n₁ sin θ₁ = n₂ sin θ₂

where n₁ and n₂ are the refractive indices of each medium.

In this case, it indicates that the light does not change direction, so the input and output angle of the interface must be the same,

       θ₁ = θ₂ = θ

substituting

          n₁ = n₂

therefore the refractive index of the two materials must be the same

When reviewing the answers, the correct one is the first

Answer:

5766.7 K

Explanation:

We are given that

Radius of Sun , R=[tex]6.96\times 10^{8} m[/tex]

Distance between the Sun and the Earth, D=[tex]1.50\times 10^{11}m[/tex]

Irradiance arriving on the Earth is the value for AMO=[tex]1350W/m^2[/tex]

We have to find the temperature at the surface of the Sun.

We know that

Temperature ,T=[tex](\frac{K_{sc}D^2}{\sigma R^2})^{\frac{1}{4}}[/tex]

Where [tex]K_{sc}=1350 W/m^2[/tex]

[tex]\sigma=5.67\times 10^{-8}watt/m^2k^4[/tex]

Using the formula

[tex]T=(\frac{1350\times (1.5\times 10^{11})^2}{5.67\times 10^{-8}\times (6.96\times 10^{8})^2})^{\frac{1}{4}}[/tex]

T=5766.7 K

Hence, the temperature at the surface of the sun=5766.7 K

Answer:

6N

Explanation:

Given parameters:

Mass of object  = 6kg

Initial velocity  = 5m/s

Final velocity  = 25m/s

Time  = 30s

Unknown:

Net force acting on the object  = ?

Solution:

From Newton's second law of motion:

   Force  = mass x acceleration

Acceleration is the rate of change of velocity with time

  Acceleration  = [tex]\frac{Final velocity - Initial velocity }{time}[/tex]  

  Force  = mass x  [tex]\frac{Final velocity - Initial velocity }{time}[/tex]  

So;

 Force  = 6 x [tex]\frac{25 - 5}{30}[/tex]    = 6N

Answer:

the second time there is a gas between you and the star,

Explanation:

When you observe the star for the first time you do not have a given between you and the star, therefore you observe the emission spectrum of the same that is formed by lines of different intensity and position that indicate the type and percentage of the atoms that make up the star.

 When you observe the same phenomenon for the second time there is a gas between you and the star, this gas absorbs the wavelengths of the star that has the same energies and the atomisms and molecular gas, therefore these lines are not observed by seeing a series of dark bands,

The information obtained from the two spectra is the same, the type of atoms that make up the star

Answer:

This is my answer

Explanation:

First convert 150 kPa to Pa:

150 × 1,000 = 150,000.

Next substitute the values into the equation:

force normal to a surface area = pressure × area of that surface.

force = 150,000 × 180.

force = 27,000,000 N.

1.First convert 150kPato Pa:

2.150 x 1,000 + 150,000

3.next substitute the values into the equations:

4.force normal to a surface area =pressure x area of that surface.

5.force=150,000 x 180.

6.force = 27,000,000N.

can i have brainliest please

Answer:

(a) the unknown inertia is 0.388 kg

(b) the average acceleration of the heavier cart is 317 m/s²

(c) the average acceleration of the lighter cart is 539 m/s²

Explanation:

Given;

mass of the first cart, m₁ = 0.66 kg

initial speed of the first cart, u₁ = 1.85 m/s

let the mass of the cart with unknown inertia be m₂

initial velocity of the second cart, u₂ = 2.17 m/s to the left

velocity of the first cart after collision, v₁ = 1.32 m/s to the left

velocity of the second cart after collision, v₂ = 3.22 m/s

time of collision, t = 0.010 s

(a) What is the unknown inertia?

Apply the principle of conservation of linear momentum, to determine the unknown inertia.

let leftward direction be negative direction

let rightward direction be positive direction

m₁u₁ + m₂u₂ = m₁v₁  + m₂v₂

0.66(1.85) + m₂(-2.17) = 0.66(-1.32) + m₂(3.22)

1.221 - 2.17m₂ = -0.8712 + 3.22m₂

1.221 + 0.8712 = 3.22m₂ + 2.17m₂

2.0922 = 5.39m₂

m₂ = 2.0922 / 5.39

m₂ = 0.388 kg

The unknown inertia is 0.388 kg

(b) the average acceleration of the heavier cart

the heavier cart has a mass of 0.66 kg

[tex]a = \frac{v_1 - u_1}{t} \\\\a = \frac{-1.32 - 1.85}{0.01} \\\\a = -317 \ m/s^2\\\\|a| = 317 \ m/s^2[/tex]

(c) the average acceleration of the lighter cart;

the lighter cart has a mass of 0.388 kg

[tex]a = \frac{v_2 - u_2}{t} \\\\a = \frac{3.22 - (-2.17)}{0.01} \\\\a =\frac{3.22 \ +\ 2.17}{0.01} \\\\a= 539\ m/s^2[/tex]

Answer:

A. 72000 C

B. 1100 W

C. 26.4 cents.

Explanation:

From the question given above, the following data were obtained:

Current (I) = 10 A

Voltage (V) = 110 V

Time (t) = 2 h

A. Determination of the charge.

We'll begin by converting 2 h to seconds. This can be obtained as follow:

1 h = 3600 s

Therefore,

2 h = 2 h × 3600 s / 1 h

2 h = 7200 s

Thus, 2 h is equivalent to 7200 s.

Finally, we shall determine the charge. This can be obtained as follow:

Current (I) = 10 A

Time (t) = 7200 s

Charge (Q) =?

Q = It

Q = 10 × 7200

Q = 72000 C

B. Determination of the power.

Current (I) = 10 A

Voltage (V) = 110 V

Power (P) =?

P = IV

P = 10 × 110

P = 1100 W

C. Determination of the cost of operation.

We'll begin by converting 1100 W to KW. This can be obtained as follow:

1000 W = 1 KW

Therefore,

1100 W = 1100 W × 1 KW / 1000 W

1100 W = 1.1 KW

Thus, 1100 W is equivalent to 1.1 KW

Next, we shall determine the energy consumption of the range. This can be obtained as follow:

Power (P) = 1.1 KW

Time (t) = 2 h

Energy (E) =?

E = Pt

E = 1.1 × 2

E = 2.2 KWh

Finally, we shall determine the cost of operation. This can be obtained as follow:

1 KWh cost 12 cents.

Therefore, 2.2 KWh will cost = 2.2 × 12

= 26.4 cents.

Thus, the cost of operating the range for 2 h is 26.4 cents.

Without friction, NO.

The speed at D depends only on the difference in height between A and D. Whatever happens between them doesn't matter.

The speed of the coaster car at point D will be affected if  the height of point C is changed.

Potencial Energy:

It is the enrgy in a body due to the position of differnt part of the object or system.

As we increase the the hight of the car the potetial enrgy increase, the gravitational acceleration on car will be more due to the high of the point C.

Therefore, the speed of the coaster car at point D will be affected if  the height of point C is changed.

To know more about  speed of the coaster car,

https://brainly.com/question/9178285

Answer: The correct statement is that the Last Quarter Moon (rises near midnight and sets near midday).

Explanation:

Phases of the moon also called the LUNAR PHASE can be defined as the different shades of illumination on the moon as seen from the earth. The moon is the natural satellite of the earth that illuminates upon reflection of light from the sun. This means it doesn't have power to shine on its own. When carefully observed, there are times it gets dark and beings to glow brighter over a period of time. This occurs because as the moon completes its four weeks lunar cycle round the earth, how much of its face we see illuminated by sunlight depends on the angle the Sun makes with the Moon.

There are 8 main types of the moon phases these includes:

--> New moon: This is when the moon is not visible to the earth because it's between the earth and the sun. It rises at sunrise and sets at sunset.

--> The waxing crescent: At this phase the moon gets brighter and illuminated from the sun that a crescent shape is seen.

--> First quarter: this occurs one week after the new moon. The moon rises at noon and sets at midnight.

--> The waxing gibbous: This occurs after the first quarter phase where more than half of the lit part of the moon is seen.

--> Full moon: This occurs when the moon and the sun are opposite each other. That is way it is said to rise at sunset and sets at sun rise.

--> The waning gibbous: this occurs when more than half of the lit part of the moon gradually becomes darker

--> Third quarter ( Last Quarter): The moon rises at midnight and sets at noon. This occurs a week after the full moon.

--> The waning crescent: This occurs after the last quarter phase where a very thin fading crescent shaped moon is seen, just before the Moon is invisible again at the start of the cycle, the new moon.

Answer:

LAW 1 :  For a given metal and frequency, the number of photoelectrons emitted is directly proportional to the intensity of the incident radiation.  

---------------------------------------------

LAW 2: For a given metal, there exists a certain frequency below which the photoelectric emission does not take place. This frequency is called threshold frequency.

-----------------------------------------------

LAW 3: For a frequency greater than the threshold frequency, the kinetic energy of photoelectrons is dependent upon frequency or wavelength but not on the intensity of light.

-----------------------------------------------

LAW 4: Photoelectric emission is an instantaneous process. The time lag between incidence of radiations and emission of electron is 10^-9 seconds.

Explanation:

Answer:

LAW 1 : For a given metal and frequency, the number of photoelectrons emitted is directly proportional to the intensity of the incident radiation. ... LAW 4: Photoelectric emission is an instantaneous process.

Answer:

Explanation:

Fluid A :

Δ V = Change in volume = (3000 - 2804) x 10⁻⁶ m³ = 196 x 10⁻⁶ m³

volume strain = Δ V / V  = 196 x 10⁻⁶ / 3000 x 10⁻⁶

= .06533

Δ P = increase in pressure = 6 x 10⁷ Pa

E = Δ P / volume strain = 6 x 10⁷ / .06533 = 91.84 x 10⁷ Pa = .92 GPa .

It is Acetone .

Fluid B :

Δ V = Change in volume = (3000 - 2862) x 10⁻⁶ m³ = 138 x 10⁻⁶ m³

volume strain = Δ V / V  = 138 x 10⁻⁶ / 3000 x 10⁻⁶

= .046

Δ P = increase in pressure = 6 x 10⁷ Pa

E = Δ P / volume strain = 6 x 10⁷ / .046 = 130.43  x 10⁷ Pa = 1.3  GPa .

It is Gasoline  .

Fluid C :

Δ V = Change in volume = (3000 - 2916) x 10⁻⁶ m³ = 84 x 10⁻⁶ m³

volume strain = Δ V / V  = 84 x 10⁻⁶ / 3000 x 10⁻⁶

= .028

Δ P = increase in pressure = 6 x 10⁷ Pa

E = Δ P / volume strain = 6 x 10⁷ / .028 = 214.28 x 10⁷ Pa = 2.14  GPa .

It is Water   .

Answer:

T = 10010 N

Explanation:

To solve this problem we must use the translational equilibrium relation, let's set a reference frame

X axis

       Fₓ-Fₓ = 0

       Fₓ = Fₓ

whereby the horizontal components of the tension in the cable cancel

Y Axis  

        [tex]F_{y} + F_{y} - W =0[/tex]

        2[tex]F_{y}[/tex] = W

let's use trigonometry to find the angles

        tan θ = y / x

        θ = tan⁻¹ (0.30 / 0.50 L)

        θ = tan⁻¹ (0.30 / 0.50 15)

        θ = 2.29º

the components of stress are

         F_{y} = T sin θ

we substitute

       2 T sin θ = W

       T = W / 2sin θ

        T = [tex]\frac{ 800}{ 2sin 2.29}[/tex]

        T = 10010 N

Static friction (magnitude Fs) keeps the car on the road, and is the only force acting on it parallel to the road. By Newton's second law,

Fs = m a = W a / g

(a = centripetal acceleration, m = mass, g = acceleration due to gravity)

We have

a = v ² / R

(v = tangential speed, R = radius of the curve)

so that

Fs = W v ² / (g R)

Solving for v gives

v = √(Fs g R / W)

Perpendicular to the road, the car is in equilibrium, so Newton's second law gives

N - W = 0

(N = normal force, W = weight)

so that

N = W

We're given a coefficient of static friction µ = 0.4, so

Fs = µ N = 0.4 W

Substitute this into the equation for v. The factors of W cancel, so we get

v = √((0.4 W) g R / W) = √(0.4 g R) = √(0.4 (9.80 m/s²) (105 m)) ≈ 20.3 m/s

Answer:

force F = 1.66 × [tex]10^{-13}[/tex] N

Explanation:

given data

proton and an electron = 865 nm

solution

we get here force that is express as

force F = k q1 q2 ÷ r²      ......................1

put here value and we get

force F = 9 × [tex]10^{9}[/tex] × [tex]\frac{1.6\times (10^{-19})^{2}}{865 \times (10^{-9})^{2}}[/tex]    

force F = 1.66 × [tex]10^{-13}[/tex] N

Answer:

This idea helps students explain why more rain forms over West Ferris than East Ferris. ... Therefore, when students explain that water vapor condenses higher in the atmosphere, they are actually explaining that water vapor condenses high in the troposphere, which is relatively low in the atmosphere.

Explanation:

Plz mark me brainliest thank u> have a good day

Answer:I think it’s self monitoring sorry if wrong

Explanation:

Answer:

It self monitoring

Explanation:

I took the test

Answer:

Explanation:

Well they told you the exact formula to use. Work is the force multiplied by  the distance through which its applied.

W = (20N)(35m)

= 700 Joules

13.) Power is the amount of work done over the time through which the work is being done.

P = W/t

= 10J/2s

= 5J/s

Answer:

the magnitude of gravitational force is 6 x 10⁻⁸ N.

Explanation:

Given;

mass of the two people, m₁ and m₂ = 90 kg

distance between them, r = 3.0 m

The magnitude of gravitational force exerted by one person on another is calculated as;

[tex]F = \frac{Gm_1m_2}{r^2} \\\\[/tex]

where;

G is gravitational constant = 6.67 x 10⁻¹¹ Nm²/kg²

[tex]F = \frac{Gm_1m_2}{r^2} \\\\F = \frac{6.67\times 10^{-11} \times \ 90 \ \times \ 90}{3^2} \\\\F = 6\times 10^{-8} \ N[/tex]

Therefore, the magnitude of gravitational force is 6 x 10⁻⁸ N.