Answer:
B
Explanation:
Write the properties of Non Metals and the families containig non Metals.
Non-Malleable and Ductile: Non-metals are very brittle, and cannot be rolled into wires or pounded into sheets. Conduction: They are poor conductors of heat and electricity. Luster: These have no metallic luster and do not reflect light.
Group 15, the nitrogen family, contains two nonmetals: nitrogen and phosphorus. These non-metals usually gain or share three electrons when reacting with atoms of other elements. Group 16, the oxygen family, contains three nonmetals: oxygen, sulfur, and selenium.
Elements: Nitrogen; Oxygen; Phosphorus; Selenium...
What do you think about the attached scenario?
A particle with charge Q and mass M has instantaneous speed uy when it is at a position where the electric potential is V. At a later time, the particle has moved a distance R away to a position where the electric potential is V2 ) Which of the following equations can be used to find the speed uz of the particle at the new position?
a. 1/2M(μ2^2-μ1^2)=Q (v1-v2)
b. 1/2M(μ2^2-μ1^2)^2=Q(v1-v2)
c. 1/2Mμ2^2=Qv1
d. 1/2Mμ2^2=1/4πx0 (Q^2/R)
Answer:
A
Explanation:
Ke = 1/2 MV^2
A sinusoidal wave is traveling on a string with speed 19.3 cm/s. The displacement of the particles of the string at x = 6.0 cm is found to vary with time according to the equation y = (2.6 cm) sin[1.8 - (5.8 s-1)t]. The linear density of the string is 5.0 g/cm. What are (a) the frequency and (b) the wavelength of the wave? If the wave equation is of the form
Answer:
Explanation:
equation of wave is given by the following equation
y = (2.6 cm) sin[1.8 - (5.8 s-1)t].
Comparing it with standard form of wave
y = A sin ( ωt - kx )
we get
ω = 5.8
2πn = 5.8
n = .92 per second
kx = 1.8
k x 6 = 1.8
k = 0.3
[tex]\frac{2\pi}{\lambda}[/tex] = 0.3
λ = 20.9 cm
take a picture of an object in your house, describe the
energy stores and transfers that happen with it. You can be as imaginative as you wish
with the object (choose something unusual), but the stores you identify and transfers
that happen must be real.
pls give me ideas of what to take a photo of for this I'm really stuck :(
An electric range has a constant current of 10 A entering the positive voltage terminal with a voltage of 110 V. The range is operated for two hours, (a) Find the charge in coulombs that passes through the range, (b) Find the power absorbed by the range, (c) If electric energy costs 12 cents per kilowatt-hour, determine the cost of operating the range for two hours.
Answer:
A. 72000 C
B. 1100 W
C. 26.4 cents.
Explanation:
From the question given above, the following data were obtained:
Current (I) = 10 A
Voltage (V) = 110 V
Time (t) = 2 h
A. Determination of the charge.
We'll begin by converting 2 h to seconds. This can be obtained as follow:
1 h = 3600 s
Therefore,
2 h = 2 h × 3600 s / 1 h
2 h = 7200 s
Thus, 2 h is equivalent to 7200 s.
Finally, we shall determine the charge. This can be obtained as follow:
Current (I) = 10 A
Time (t) = 7200 s
Charge (Q) =?
Q = It
Q = 10 × 7200
Q = 72000 C
B. Determination of the power.
Current (I) = 10 A
Voltage (V) = 110 V
Power (P) =?
P = IV
P = 10 × 110
P = 1100 W
C. Determination of the cost of operation.
We'll begin by converting 1100 W to KW. This can be obtained as follow:
1000 W = 1 KW
Therefore,
1100 W = 1100 W × 1 KW / 1000 W
1100 W = 1.1 KW
Thus, 1100 W is equivalent to 1.1 KW
Next, we shall determine the energy consumption of the range. This can be obtained as follow:
Power (P) = 1.1 KW
Time (t) = 2 h
Energy (E) =?
E = Pt
E = 1.1 × 2
E = 2.2 KWh
Finally, we shall determine the cost of operation. This can be obtained as follow:
1 KWh cost 12 cents.
Therefore, 2.2 KWh will cost = 2.2 × 12
= 26.4 cents.
Thus, the cost of operating the range for 2 h is 26.4 cents.
A car enters a 105-m radius flat curve on a rainy day when the coefficient of static friction between its tires and the road is 0.4. What is
the maximum speed which the car can travel around the curve without sliding
Static friction (magnitude Fs) keeps the car on the road, and is the only force acting on it parallel to the road. By Newton's second law,
Fs = m a = W a / g
(a = centripetal acceleration, m = mass, g = acceleration due to gravity)
We have
a = v ² / R
(v = tangential speed, R = radius of the curve)
so that
Fs = W v ² / (g R)
Solving for v gives
v = √(Fs g R / W)
Perpendicular to the road, the car is in equilibrium, so Newton's second law gives
N - W = 0
(N = normal force, W = weight)
so that
N = W
We're given a coefficient of static friction µ = 0.4, so
Fs = µ N = 0.4 W
Substitute this into the equation for v. The factors of W cancel, so we get
v = √((0.4 W) g R / W) = √(0.4 g R) = √(0.4 (9.80 m/s²) (105 m)) ≈ 20.3 m/s
If a cyclist travels 30 km in 2 h, What is her average speed?
Answer:
15km/h
Explanation:
→ Speed = Distance ÷ Time
30 ÷ 2 = 15km/h
Which of the following is a mixture?
a air
biron
Chydrogen
d nickel
Answer:
it will option option A hope it helps
1. (6x + 8)(5x - 8)
a. 30x2 + 49x + 20
2. (5x + 6(5x - 5)
b. 24x3 + 8x2 + 6x + 4
3. (6x + 3)(6x - 4)
c. 25x2 + 5x - 30
4. (6x + 5)(5x + 5)
d. 30x2 - 8x - 64
e. 36x2 - 6x - 1
5. (4x + 2) (6x2 - x + 2)
Answer:
form 1 question??????????
An RC car is carrying a tiny slingshot with a spring constant of 85 N/m at 0.2 m off the ground at 5.6 m/s. The sling shot is pulled back 3.5 cm from a relaxed state and shoots a 25 g steel pellet in the same direction the car is moving. What is the velocity of the steel pellet relative to the ground as it leaves the sling shot
Answer:
The velocity of the steel pellet relative to the ground when it leaves the sling shot is approximately 5.960 meters per second.
Explanation:
Let suppose that RC car-slingshot-steelpellet is a conservative system, that is, that non-conservative forces (i.e. friction, air viscosity) can be neglected. The velocity of the steel pellet can be found by means of the Principle of Energy Conservation and under the consideration that change in gravitational potential energy is negligible and that the RC car travels at constant velocity:
[tex]\frac{1}{2}\cdot (m_{C}+m_{P})\cdot v_{o}^{2} + \frac{1}{2}\cdot k\cdot x^{2} = \frac{1}{2}\cdot m_{C}\cdot v_{o}^{2} + \frac{1}{2}\cdot m_{P}\cdot v^{2}[/tex]
[tex]\frac{1}{2}\cdot m_{P}\cdot v_{o}^{2} + \frac{1}{2}\cdot k\cdot x^{2} = \frac{1}{2}\cdot m_{P}\cdot v^{2}[/tex]
[tex]m_{P}\cdot v_{o}^{2} + k\cdot x^{2} = m_{P}\cdot v^{2}[/tex]
[tex]v^{2} = v_{o}^{2} + \frac{k}{m_{P}}\cdot x^{2}[/tex]
[tex]v = \sqrt{v_{o}^{2}+\frac{k}{m_{P}}\cdot x^{2} }[/tex] (1)
Where:
[tex]v_{o}[/tex] - Initial velocity of the steel pellet, measured in meters per second.
[tex]v[/tex] - Final velocity of the steel pellet, measured in meters per second.
[tex]k[/tex] - Spring constant, measured in newtons per meter.
[tex]m_{P}[/tex] - Mass of the steel pellet, measured in kilograms.
[tex]m_{C}[/tex] - Mass of the RC car, measured in kilograms.
[tex]x[/tex] - Initial deformation of the spring, measured in meters.
If we know that [tex]v_{o} = 5.6\,\frac{m}{s}[/tex], [tex]k = 85\,\frac{N}{m}[/tex], [tex]m_{P} = 0.025\,kg[/tex] and [tex]x = 0.035\,m[/tex], then the velocity of the steel pellet relative to the ground when it leaves the sling shot is:
[tex]v = \sqrt{\left(5.6\,\frac{m}{s} \right)^{2}+\frac{\left(85\,\frac{N}{m} \right)\cdot (0.035\,m)^{2}}{0.025\,kg} }[/tex]
[tex]v \approx 5.960\,\frac{m}{s}[/tex]
The velocity of the steel pellet relative to the ground when it leaves the sling shot is approximately 5.960 meters per second.
calculate ine gravitational potential energy of the ball using pe=m×g×h.(use g=9.8 n/kg)
A 4.0-kilogram ball held 1.5 meters above the floor has ________ joules of potential energy
Answer:
58.8J
Explanation:
Given parameters;
Mass of ball = 4kg
Height above the floor = 1.5m
g = 9.8n/kg
Unknown:
Potential energy = ?
Solution:
The potential energy of a body is the energy due to the position of the body.
It is mathematically expressed as:
Potential energy = mass x acceleration due to gravity x height
Potential energy = 4 x 9.8 x 1.5 = 58.8J
Car À moves at a speed of 8m/s for 43 seconds. Car B moves at a speed of 7 m/s for 50 seconds. Which car traveled a longer distance
Please show working
Distance = (speed) x (time)
Car A: Distance = (8 m/s) x (43 s) = 344 meters
Car B: Distance = (7 m/s) x (50 s) = 350 meters
350 meters is a longer distance than 344 meters.
Car-B traveled a longer distance than Car-A did.
Answer:
[tex]\boxed {\boxed {\sf Car \ B : 350 \ meters }}[/tex]
Explanation:
Distance is equal to the product of speed and time.
[tex]d=s*t[/tex]
1. Car A
Car A has a speed of 8 meters per second and travels for 43 seconds.
[tex]s= 8 \ m/s \\t= 43 \ s[/tex]
Substitute the values into the formula.
[tex]d= 8 \ m/s *43 \ s[/tex]
Multiply and note that the seconds will cancel out.
[tex]d= 8 \ m*43= 344 \ m[/tex]
2. Car B
Car B has a speed of 7 meters per second and travels for 50 seconds.
[tex]s= 7 \ m/s \\t= 50 \ s[/tex]
Substitute the values in and multiply.
[tex]d= 7 \ m/s * 50 \ s[/tex]
[tex]d= 7 \ m * 50 = 350 \ m[/tex]
350 meters is a longer distance than 344 meters, so Car B traveled the longer distance.
Consider a swimmer that swims a complete round-trip lap of a 50 m long pool in 100 seconds. The swimmer's... average speed is 0 m/s and average velocity is 0 m/s. average speed is 0.5 m/s and average velocity is 0.5 m/s. average speed is 1 m/s and average velocity is 0 m/s. average speed is 0 m/s and average velocity is 1 m/s.What is the swimmers average speed and average velocity?
Answer:
average speed is 1 m/s and average velocity is 0 m/s.
Explanation:
Given that :
Length of round trip = 50 m
Time taken = 100 seconds
The average speed :
Total distance / total time taken
Length of complete round trip :
(50 + 50) m, total. Distance = 100 m
100 / 100 = 1m/s
The average velocity :
Total Displacement / total time taken
Total Displacement of round trip = end point - start point = 0
0 / 100 = 0
Average speed is 1 m/s and average velocity is 0 m/s.
The average speed is defined as the ratio of distance to time. Speed is a scalar quantity hence it does not take direction into account while velocity is a vector quantity hence it takes direction into account.
The speed is obtained from;
Speed = Distance/time = 2(50 m)/100 s = 1 m/s.
The velocity is 0 m/s since it is complete round-trip lap.
Learn more about speed: https://brainly.com/question/7359669
An 8.00 kg mass moving east at 15.4 m/s on a frictionless horizontal surface collides with a 10.0 kg object that is initially at rest. After the collision, the 8.00 kg object moves south at 3.90 m/s. (a) What is the velocity of the 10.0 kg object after the collision
Answer:
9.3m/s
Explanation:
Based on the law of conservation of momentum
Sum of momentum before collision = sum of momentum after collision
m1u1 +m2u2 = m1v1+m2v2
m1 = 8kg
u1 = 15.4m/s
m2 = 10kg
u2 = 0m/s(at rest)
v1 = 3.9m/s
Required
v2.
Substitute
8(15.4)+10(0) = 8(3.9)+10v2
123.2=31.2+10v2
123.2-31.2 = 10v2
92 = 10v2
v2 = 92/10
v2 = 9.2m/s
Hence the velocity of the 10.0 kg object after the collision is 9.2m/s
Does changing the height of point C affect the speed of the coaster car at point D?
Without friction, NO.
The speed at D depends only on the difference in height between A and D. Whatever happens between them doesn't matter.
The speed of the coaster car at point D will be affected if the height of point C is changed.
Potencial Energy:
It is the enrgy in a body due to the position of differnt part of the object or system.
As we increase the the hight of the car the potetial enrgy increase, the gravitational acceleration on car will be more due to the high of the point C.
Therefore, the speed of the coaster car at point D will be affected if the height of point C is changed.
To know more about speed of the coaster car,
https://brainly.com/question/9178285
As a laudably skeptical physics student, you want to test Coulomb's law. For this purpose, you set up a measurement in which a proton and an electron are situated 865 nm from each other and you study the forces that the particles exert on each other. As expected, the predictions of Coulomb's law are well confirmed. You find that the forces are attractive and the magnitude of each force is:______
Answer:
force F = 1.66 × [tex]10^{-13}[/tex] N
Explanation:
given data
proton and an electron = 865 nm
solution
we get here force that is express as
force F = k q1 q2 ÷ r² ......................1
put here value and we get
force F = 9 × [tex]10^{9}[/tex] × [tex]\frac{1.6\times (10^{-19})^{2}}{865 \times (10^{-9})^{2}}[/tex]
force F = 1.66 × [tex]10^{-13}[/tex] N
a wooden block is cut into two pieces, one with three times the mass of the other. a depression is made in both faces of the cut so that a fire cracker can be placed in it and the block is reassembled. the reassembled block is set on rough surface and the fuse is lit. when the fire cracker explodes, the two blocks separate. what is the ratio of distances traveled by blocks?
Answer:
1/9
Explanation:
Let A denote the bigger piece and let B denote the smaller piece.
We are told that one with three times the mass of the other.
Therefore, we have;
M_a = 3M_b
Firecracker is placed in the block and it explodes and thus, momentum is conserved.
Thus;
V_ai = V_bi = 0
Where V_ai is initial velocity of piece A and V_bi is initial velocity of piece B.
Since initial momentum equals final momentum, we have;
P_i = P_f
Thus;
0 = (M_a × V_af) + (M_b × V_bf)
Since M_a = 3M_b, we have;
(3M_b × V_af) + (M_b × Vbf) = 0
Making V_af the subject, we have;
V_af = -⅓V_bf
The kinetic energy gained by each block during the explosion will later be lost due to the negative work done by friction. Thus;
W_f = -½M_b•(v_bf)²
Now, let's express the work is in terms of the force and the distance.
Thus;
W_f = F_f × Δx × cos 180°
Frictional force is also expressed as μmg
Thus;
W_f = -μM_b × g × Δx
Earlier, we saw that;
W_f = -½M_b•(v_bf)²
Thus;
-½M_b•(v_bf)²= -μM_b × g × Δx
Δx = (v_bf)²/2μg
Let the distance travelled by block A be Δx_a and that travelled by B be Δx_b
Thus;
Δx_a/Δx_b = ((v_ba)²/2μg)/((v_bf)²/2μg)
Δx_a/Δx_b = ((v_af)²/((v_bf)²)
Δx_a/Δx_b = (-⅓V_bf)²/(V_bf)²
Δx_a/Δx_b = 1/9
