The capacitance of the circuit (in f) is 2.31×10⁻⁵F for the rc circuit with a time constant of 5.35 s. if the total resistance in the circuit is 231.2 k.
What is the capacitance of the circuit?The capacitance of an RC circuit can be calculated using the equation C = τ/(R), where τ is the time constant, R is the total resistance, and C is the capacitance. For this RC circuit, the time constant is 5.35s and the total resistance is 231.2 k. Therefore, the capacitance is 5.35s/(231.2k) = 2.31×10⁻⁵F.
Time constant of the RC circuit, τ = 5.35s
Total resistance in the circuit, R = 231.2 kΩ = 231200 Ω
Capacitance of the circuit = ?
We know that, Time constant (τ) of a RC circuit = R × C.
where, R is the resistance in ohms, C is the capacitance in farads. Substitute the given values in the above equation:
τ = RC
5.35 s = R × C231200 Ω × C = 5.35 s
C = 5.35 s / 231200 Ω
C = 2.31 × 10⁻⁸ F.
Therefore, the capacitance of the circuit is 2.31 × 10⁻⁸ F.
Read more about circuit :
https://brainly.com/question/26064065
#SPJ11
determine whether each geologic feature is being caused by tensional, compressional, or shear stresses by analyzing the directions of the forces being applied.
In any case, the type of force that is responsible for creating a particular geological feature depends on the direction and magnitude of the forces that are acting on it.
Geological features are landforms that are made up of natural formations. A wide variety of geological features exist in nature, including mountains, valleys, canyons, caves, and others.
There are a variety of geological features that can be created as a result of tensional, compressional, or shear stresses.
Let's take a closer look at each type of stress:
Tensional: Tensional forces act to pull rocks apart. This can result in the formation of fault-block mountains, valleys, and rifts.
Compressional: Compressional forces act to push rocks together. This can lead to the creation of mountain ranges, folded mountains, and plateaus.
Shear Stresses: Shear stresses act to twist or bend rocks. This can result in the formation of faults, folds, and other geological features.
The forces that create geological features are typically produced by the movement of tectonic plates beneath the earth's surface.
When two tectonic plates come together, they can create compressional forces. When they move apart, they can create tensional forces.
When they slide past each other, they can create shear stresses. Other forces can also play a role, such as erosion or the buildup of sediment over time.
To know more about Geological features:https://brainly.com/question/19925491
#SPJ11
a particle's velocity is described by the function vx=kt2 , where vx is in m/s , t is in s , and k is a constant. the particle's position at t0=0s is x0 = -5.40 m . at t1 = 2.00 s , the particle is at x1 = 5.80 m .
A particle's velocity is described by the function vx=kt2 , where vx is in m/s , t is in s , and k is a constant. The particle's position at t0=0s is x0 = -5.40 m. At t1 = 2.00 s , the particle is at x1 = 5.80 m. The value of k is 2.80 m/s2.
The given equation describes the velocity of a particle in terms of a constant, k, and time, t. The velocity, vx, is given in m/s. The initial position of the particle at t0=0s is x0=-5.40 m, and at t1=2.00 s the particle is at x1=5.80 m. To find the value of the constant k, we can solve the equation for the change in velocity Δvx.
Δvx = vx1 – vx0 = k(t12 – t02)
Δvx = 5.80 – (-5.40) = 11.20 m/s
k = (11.20 m/s) / (2.002 s2) = 2.80 m/s2
Now that we have found the value of the constant k, we can use it to find the velocity of the particle at any time t. For example, at t2=4.00 s the velocity of the particle is vx2=11.20 m/s. This can be calculated using the equation vx2 = k(t22) = 2.80(4.002) = 11.20 m/s.
From the velocity equation, we can also calculate the position of the particle at any time t. The position of the particle at t2=4.00 s is x2= 11.20(4.00) = 44.80 m. We can also calculate the position of the particle at any other time t, by simply substituting in the corresponding value of t into the equation.
In conclusion, the equation vx = kt2 describes the velocity of a particle in terms of a constant, k, and time, t. Using this equation, we can calculate the velocity and position of the particle at any given time.
For more such questions on Velocity.
https://brainly.com/question/14528397#
#SPJ11
Complete Question:
A particle’s velocity is described by the function vx = [tex]kt^2m/s[/tex], where k is a constant and t is in s. The particle’s position at [tex]t_0[/tex] = 0s is [tex]x_0[/tex] = -5.40 m. At [tex]t_1[/tex] = 2.00 s, the particle is at [tex]x_1[/tex] = 5.80 m. Determine the value of the constant k. Be sure to include the proper units
A 2 kg object is released from rest near the surface of a planet such that its gravitational field is considered to be constant. The mass of the planet is unknown. The
object's speed after falling for 3 sis 75 m/s. Air resistance is considered to be negligible, Calculate the weight of the 2 kg object on the planet of unknown mass.
2N
B
25 N
50N
D
75 N
Imagine sitting on a merry-go-round and riding along as it spins. Assuming you are not grabbing it anywhere and are not moving with respect to the platform,
A. static friction (directed inwards) causes you to accelerate.
B. you are not accelerating because you aren't moving on the platform.
C. static friction (directed outwards) causes you to accelerate.
D. sliding friction makes you accelerate inwards.
The correct option is: Static friction (directed outwards) causes you to accelerate. (Option C)
When you sit on a merry-go-round, you are not moving relative to the platform. Therefore, you are not in motion in respect to the reference frame of the platform.
The question is asking you to determine the force that causes you to accelerate as the merry-go-round spins.
Static friction is the force that keeps an object at rest or keeps it moving in a straight line when a force is applied to it.
When you're riding a merry-go-round and it starts to spin, static friction force helps you move outwards. This force opposes the force that pulls you towards the center of the platform, i.e., centripetal force.
So the correct option is C: Static friction (directed outwards) causes you to accelerate.
To know more about "Static friction" refer here:
https://brainly.com/question/13828735#
#SPJ11
In outer space will a liquid in a beaker exert a pressure on the bottom or on the sides of a beaker?
Answer:
Yo dude, if you had a beaker of liquid in outer space, it wouldn't push down on the bottom or the sides of the beaker like it would on Earth. In space, there's no gravity to make the liquid settle down, so it forms a round shape because of surface tension. So basically, the liquid would just float around in a ball inside the beaker. If you moved the beaker around, the liquid would just roll around with it like a bouncy ball.
during a one-second period, air is added into a rigid tank. the volume of the tank is 3 m3 and the initial density of air is 1.2 kg/m3; at the end of the charging process, the density of air reaches 6.3 kg/m3. what is the mass flow rate of air that is entering the tank?
The mass flow rate of air that is entering the tank is 15.3 kg/s.
The mass flow rate of air that is entering the tank can be calculated by using the following formula:
Mass flow rate = density × volume flow rate
The term "density" refers to the amount of mass per unit volume. It is calculated as the mass of an object divided by its volume. Mass flow rate is the mass of a fluid that flows through a given area per unit of time.
The volume of the tank is 3 m³.
The initial density of air is 1.2 kg/m³.
At the end of the charging process, the density of air reaches 6.3 kg/m³.
We will first find the volume flow rate.
The volume flow rate is equal to the change in volume over time.
Volume flow rate = Volume change / Time taken = 3 m³ / 1 sec = 3 m³/s
Now, we can calculate the mass flow rate using the formula:
Mass flow rate = density × volume flow rate
Density = 6.3 kg/m³ − 1.2 kg/m³ = 5.1 kg/m³
Mass flow rate = 5.1 kg/m³ × 3 m³/s = 15.3 kg/s
Therefore, the mass flow rate of air entering the tank is 15.3 kg/s.
Learn more about density:
https://brainly.com/question/1354972
#SPJ11
The straight section of the line in figure 10 can be used to calculate the useful power output of the kettle explain how
Using the line's straight segment in figure 10, it is possible to determine the usable power output of the kettle.
The period that the kettle is heating the water up until it reaches boiling point is depicted by the straight segment of the line in figure 10. Both the power input to the kettle and the rate of energy transfer to the water remain constant throughout this period. Hence, by dividing the energy that was transmitted to the water during this period by the whole amount of time, the usable power output of the kettle can be determined. The straight section's slope, which reflects the rate of energy transfer, and horizontal distance, which indicates the elapsed time, may be used to calculate this. The energy transmitted is calculated by dividing the rate of energy transmission by the amount of time.
learn more about power here:
https://brainly.com/question/22285866
#SPJ4
for the given input voltage amplitude (200 mvpp), what is the maximum gain that this amplifier will be able to produce? show your calculation below.
The maximum gain of an amplifier that produces an output voltage amplitude of 50 Vpp with an input voltage amplitude of 200 mVpp is 25. The formula to calculate gain is output voltage amplitude divided by input voltage amplitude.
In this case, we are given an input voltage of 200 mVpp, so the maximum gain of this amplifier can be calculated as follows:
Gain = Output Voltage/Input Voltage = Output Voltage/200 mVpp
Therefore, the maximum gain of this amplifier is equal to the output voltage. In other words, the maximum gain of this amplifier is equal to the voltage output of the amplifier.
To calculate the output voltage of the amplifier, we need to know the supply voltage and the resistance of the load. Assuming the supply voltage is 5V and the load resistance is 10k ohms, the output voltage can be calculated as follows:
Output Voltage = Supply Voltage * Load Resistance / (Load Resistance + Output Resistance) = 5V * 10k ohms / (10k ohms + 10k ohms) = 5V
Therefore, the maximum gain of this amplifier is 5V/200 mVpp = 25.
To summarize, the maximum gain of this amplifier is 25, calculated by dividing the output voltage by the input voltage. The output voltage can be calculated by knowing the supply voltage and load resistance.
For more such questions on Maximum voltage gain.
https://brainly.com/question/31086456#
#SPJ11
a researcher is studying the distribution of auxin in roots and stems exposed to sunlight. he notices that more auxin collects in the sides of stems and roots that are not exposed to light. why?
The researcher's observation that more auxin collects in the sides of stems and roots that are not exposed to light is likely due to the phenomenon of phototropism.
In the process of phototropism, light influences the direction and rate of growth of plant cells. In particular, light induces the cells on one side of a stem or root to create less auxin than the cells on the shaded side. Less auxin is produced on the lighted side and more auxin is produced on the shaded side as a result. The hormone auxin is essential for controlling the growth and development of plants. Auxin generally promotes cell growth and elongation at greater concentrations while inhibiting cell elongation at lower concentrations. Since the cells on the lighted side of the stem or root will contain less auxin when there is light.
Learn more about auxin here:
https://brainly.com/question/21591280
#SPJ4
When a ball bounces against a wall there will be large change in velocity in short period of time. This means the ____ is large, hence the net ___ must be proportionately large as well.
A change in velocity in short period of time means the acceleration is large, hence the net force must be proportionately large as well.
What is a force?A force is a physical quantity that induces a body to undergo an alteration in speed, direction of motion, or shape. A force can be classified as a push or a pull. When forces are equal, the forces are balanced and the object is not moving. Otherwise, if the forces are not equal, making it unbalanced will not give the object any movement.
The force that induces the change in the speed or direction of an object is referred to as a net force. The net force is equal to the product of the mass of the object and its acceleration. Newton (N) is the unit of measurement for force.
When a ball bounces against a wall, there will be a large change in velocity in a short period of time. This means the acceleration is large, hence the net force must be proportionately large as well.
Learn more about acceleration here: https://brainly.com/question/26408808
#SPJ11
A resistor is constructed by shaping a material of resistivity p into a hollow cylinder of length L and with inner and outer radii ra and rb, respectively (Fig. P27.66). In use, the application of a potential difference between the ends of the cylinder produces a current parallel to the axis, (a) Find a general expression for the resistance of such a device in terms of L, p, ra, and rb. (b) Obtain a numerical value for. R when L = 4.00 cm, ra = 0.500 cm, rb = 1.20 cm, and p = 3.50 times 105 Ohm m. (c) Now suppose that the potential difference is applied between the inner and outer surfaces so that the resulting current flows radially outward. Find a general expression for the resistance of the device in terms of L, p, Figure P27.66 ra, and rb. (d) Calculate the value of R, using the parameter values given in part (b).
Explanation:
Refer to pic...........
the maximum energy of photoelectrons from aluminium is 2.3 ev for radiation of 2000 a and 0.90 ev for radiation of 3130 a. use this data to calculate plancks constant and the work function of aluminium
The maximum energy of photoelectrons from aluminium is 2.3 eV for radiation of 2000 Å and 0.90 eV for radiation of 3130 Å.
To calculate Planck's constant and the work function of aluminium, we need to use the equation:
h = E2 - E1/ λ2 - λ1
Where h is Planck's constant, E1 and E2 are the maximum energy of photoelectrons for each wavelength, and λ1 and λ2 are the wavelengths.
Using the given data, we have:
h = (2.3 - 0.90) / (2000 - 3130)
Therefore, h = -1.4 eV / -930 Å, which simplifies to h = 0.0015 eVÅ.
The work function of aluminium is equal to the maximum energy of the photoelectrons for the longest wavelength, in this case, 0.90 eV. Therefore, the work function of aluminium is 0.90 eV.
Learn more about photoelectrons at brainly.com/question/16772624
#SPJ11
A solar sailplane is going from Earth to Mars. Its sail is oriented to give a solar radiation force of FRad = 7.70 × 102 N. The gravitational force due to the Sun is 173 N and the gravitational force due to Earth is 1.00 × 102 N. All forces are in the plane formed by Earth, Sun, and sailplane. The mass of the sailplane is 14,900 kg. What is the magnitude of the acceleration on the sailplane? Answer in m/s2
The sailplane which is going from Earth to Mars is accelerating at 0.033 m/s² in the direction of solar radiation force.
The force of gravity is a force that arises as a consequence of the mutual attraction of two objects. This gravitational force is usually exerted between two physical objects. Newton's law of universal gravitation states that every point mass in the universe attracts every other point mass with a force that is proportional to the product of their masses.
Acceleration is the rate at which an object changes its speed or direction. Acceleration is a vector quantity that can be positive or negative. If the acceleration is negative, the object slows down. If the acceleration is positive, the object speeds up.
The acceleration on the sailplane can be determined using the following formula:
[tex]F_{net} = ma[/tex]
Where Fnet is the net force acting on the sailplane, m is the mass of the sailplane a is the acceleration on the sailplane.[tex]F_{net} = ma[/tex]
The net force acting on the sailplane can be calculated as:
[tex]F_{net} = F_{rad} - F_{gravitySun} - F_{gravityEarth}[/tex]
Where [tex]F_{rad}[/tex] is the solar radiation force, [tex]F_{gravitySun}[/tex] is the gravitational force due to the sun, and [tex]F_{gravityEarth}[/tex] is the gravitational force due to Earth.
Putting the given values in the above formula:
[tex]F_{net} = 7.70 \times 10^2 N - 173 N - 1.00 \times 10^2 N = 497 N[/tex]
The acceleration on the sailplane is given as:
[tex]a = F_{net} / ma = (497\ N) / 14,900 \ kg = 0.033 \ m/s^2[/tex]
The magnitude of the acceleration on the sailplane is 0.033 m/s² (rounded to three significant figures).
Learn more about Newton's law:
https://brainly.com/question/28171613
#SPJ11
Calculate the translational speed of a cylinder when it reaches the foot of an incline 7.20 m high. Assume it starts from rest and rolls without slipping.
Express your answer using three significant figures and include the appropriate units. Thank you!!
The translational speed of the cylinder when it reaches the foot of the incline is approximately 9.43 m/s.
We can use conservation of energy to solve this problem. The initial energy of the cylinder is all potential energy, and the final energy is all kinetic energy. The potential energy at the bottom of the incline is zero.
The potential energy of the cylinder at the top of the incline is given by:
PE = mgh
where m is the mass of the cylinder, g is the acceleration due to gravity, and h is the height of the incline. Substituting the given values, we get:
PE = (mass of cylinder) x (acceleration due to gravity) x (height of incline) = mgh
The kinetic energy of the cylinder at the bottom of the incline is given by:
KE = (1/2)mv^2
where v is the translational speed of the cylinder at the bottom of the incline.
According to the conservation of energy, the initial potential energy is equal to the final kinetic energy, so we can set these two expressions equal to each other:
mgh = (1/2)mv^2
We can cancel the mass of the cylinder from both sides, and solve for v:
v = sqrt(2gh)
Substituting the given values, we get:
v = sqrt(2 x 9.81 m/s^2 x 7.20 m) ≈ 9.43 m/s
Therefore, the translational speed of the cylinder when it reaches the foot of the incline is approximately 9.43 m/s.
For more such questions on Cylinder
https://brainly.com/question/23935577
#SPJ11
the end result of a theory that is not verified is
Unproven theories ultimately cannot be regarded as scientific facts or principles and are not generally recognised by the scientific community.
A well-supported explanation of a natural occurrence in science that has passed rigorous examination and is backed by empirical data is referred to as a theory. A hypothesis, however, cannot be regarded as a scientific fact or principle if it is not backed up by empirical data or if it has not undergone extensive testing and verification. The scientific community frequently rejects unproven notions with scant empirical backing and may even label them as pseudoscientific or non-scientific. This is so that scientific theories and findings may be evaluated and verified frequently. Science does this by using evidence-based reasoning and critical thinking. Unproven theories are therefore eventually not regarded as being a part of the corpus of scientific knowledge.
learn more about theories here:
https://brainly.com/question/1759635
#SPJ4
member bc exerts on member ac a force p directed along line bc. knowing that p must have a 325-n horizontal component, determine (a) the magnitude of the force p, (b) its vertical component.
(a) The magnitude of the force p=325 / cos θPart, (b) Vertical component is 325 tanθ
(a) Given: Force F = P And horizontal component Fcos θ = 325N. Here, θ is the angle made by the force with the horizontal, and θ is unknown. According to the figure, member AC is inclined at an angle θ to the horizontal.
Let's resolve the force P into vertical and horizontal components. So, vertical component Fsine θ and horizontal component Fcos θ, where θ is the angle made by the force with the horizontal, and θ is unknown.
Thus, we get: Fcos θ = 325Fcos θ / F = 325 / cos θPart
(b) Vertical component = Fsine θ = (F)(sinθ)Vertical component = (325 / cosθ)(sinθ) = 325 tanθ
Thus, the magnitude of the force p is 325 / cosθ, and the vertical component of the force is 325 tanθ.
To know more about force, refer here:
https://brainly.com/question/13191643#
SPJ11#
A horizontal force of magnitude 35.0N pushes a block of mass 4.00kg across a floor where the coefficient of kinetic friction is 0.600. (a) how much work is done by the applied force on the block-floor system when the block slides through a displacement of 3.00m across the floor? (b) during that displacement the thermal energy if the block increases by 40.0J. what is the increase in thermal energy of the floor? (c) what is the increase in the kinetic energy of the block?
Answer to following (a) , (b) and (c) question are: 63.00 J, 40.0 J, 63.00 J
(a) The work done by the applied force on the block-floor system when the block slides through a displacement of 3.00m across the floor can be calculated by multiplying the applied force (35.0 N) and the displacement (3.00 m), with a coefficient of kinetic friction (0.600) for the system. Thus, the work done is 35.0N * 3.00m * 0.600 = 63.00 J.
(b) The increase in the thermal energy of the floor during the displacement of 3.00m is equal to the thermal energy of the block (40.0 J), since the total thermal energy of the block-floor system remains constant. Therefore, the increase in thermal energy of the floor is 40.0 J.
(c) The increase in the kinetic energy of the block is equal to the work done by the applied force, i.e., 63.00 J.
To know more about "coefficient of kinetic friction" refer here:
https://brainly.com/question/13754413#
#SPJ11
Acceleration due to gravity is 9.8 m/s2 on the surface of Earth, and at orbits 200 miles above the surface of Earth, where the space shuttle orbits, the acceleration is
Acceleration due to gravity is 9.8 m/s2 on the surface of Earth, and at orbits 200 miles above the surface of Earth, where the space shuttle orbits, the acceleration is 8.78 m/s².
What is gravitational force?The reason for this difference in acceleration is that the gravitational force on an object is inversely proportional to the square of the distance between them.
Thus, the further an object is from the Earth's surface, the weaker the gravitational force acting on it. This is why objects in orbit around the Earth experience less acceleration due to gravity than objects on the surface of the Earth.
To know more about gravitational force:
https://brainly.com/question/3009841
#SPJ11
if two identical resistors are connected in series to a battery, does the battery have to supply more power or less power than when only one of the resistors is connected? explain
The battery has to supply more power when two resistors are connected in series than when only one resistor is connected. This is because the power dissipated in a series circuit is equal to the sum of the power dissipated in each resistor.
When two identical resistors are connected in series to a battery, the battery has to supply more power than when only one of the resistors is connected. This is because the resistors offer resistance, which results in the dissipation of energy as heat. The higher the resistance of a resistor, the more power it requires to operate.Resistors consume energy as they offer resistance to the flow of current. The power supplied by the battery is converted to heat energy in the resistor, and the amount of heat energy dissipated is determined by the resistance of the resistor. The greater the resistance of the resistor, the more power it requires to function.
As a result, when two identical resistors are connected in series to a battery, the battery has to supply more power than when only one of the resistors is connected, to produce the same current through the circuit. Therefore, if two resistors of equal value are connected in series, the total power dissipated is twice that of when a single resistor is connected.
Read more about resistors :
https://brainly.com/question/13606415
#SPJ11
You are the process engineer at Corvallis Automobiles Inc., and you have received an order to turn a cylindrical bar on an engine lathe to the dimensions specified in Fig. 1. For this order you will use cylindrical bar stock that is 48-inches long and 4-inches in diameter. The 48-inch length bar will be chucked in the lathe and supported at the opposite end using a live center. You are planning to complete the operation in one pass using a cutting speed of 400 ft./min. and a feed of 0.010 in./rev. Determine the following: a) The required depth of cut (in inches) b) The material removal rate (in cubic inches per minute)
c) The time required to complete the cutting pass (in minutes)
a. the depth of cut is 0.625 inches.
b. the material removal rate is 0.003125 cubic inches per minute.
c. the time required to complete the cutting pass is 20 minutes.
How do we calculate?a) The required depth of cut can be determined by :
DOC = (4 in - 2.75 in)/2 = 0.625 in
Therefore, the depth of cut is 0.625 inches.
b) The material removal rate can be found by applying:
MRR = DOC x Width of cut x Feed rate
assuming we are using a standard carbide insert tool with a width of cut of 0.5 inches.
MRR = 0.625 in x 0.5 in x 0.010 in/rev = 0.003125 cubic inches per minute
c) The time required to complete the cutting pass is determined by:
Time = Length of cut / (Cutting speed x Width of cut x Feed rate)
Time = 48 in / (400 ft/min x (0.5 in) x (0.010 in/rev) x (1/12 ft/in)) = 20 minutes
Learn more about material removal rate at: https://brainly.com/question/13106351
#SPJ1
a big block of mass m(10kg) slides down a frictionless inclined at an angle 30 with the horizontal table. initially the block is at the top of the incline at rest. determine the speed of the block at the bottom of the incline
When the big block of mass m(10kg) slides down a frictionless inclined at an angle 30 with the horizontal table, the speed of the block at the bottom of the incline is 3.14 m/s.
Given that
Mass of the block, m = 10 kg.
Angle of inclination, θ = 30°
Initial velocity, u = 0.
Frictional force, f = 0.
Using the formula for gravitational force, F = mg
where, g = 9.8 m/s² (acceleration due to gravity)
F = mg= 10 kg × 9.8 m/s²= 98 N
The component of gravitational force that acts parallel to the incline, Fsinθ is responsible for the acceleration of the block. Fsinθ = ma; Where a is the acceleration of the block.
a= (98 N)sin 30° / 10 kg= 4.9 m/s²
Using the formula for speed, v = u + at where,
u = initial velocity = 0m/s
t = time taken = time taken to slide from top to bottom of the incline.= √(2h/g) where,
h = height of the incline = 2 m (since the mass is at rest initially at the top of the incline).
Therefore, t = √(2 × 2 m / 9.8 m/s²)= 0.64 s
Substituting the values in the above formula, v = u + at= 0 + (4.9 m/s² × 0.64 s)= 3.14 m/s.
To know more about speed, refer here:
https://brainly.com/question/29309579#
SPJ11#
In which of the following cases does a car have a negative velocity and a positive acceleration? A car that is traveling in the ................. (A) -x direction at a constant 10 m/s. (B) - direction increasing in speed. (C) +x direction increasing in speed. (D) - direction decreasing in speed. (E) +x direction decreasing in speed.
In the case where the car is traveling in the -x direction and decreasing in speed, it has a negative velocity and a positive acceleration. Therefore, option D is the correct answer. In this case, the car is traveling in the - direction and decreasing in speed. Therefore, it has a negative velocity and a positive acceleration.
Let's discuss the given options one by one:
(A) In this case, the car is traveling in the -x direction at a constant speed. Therefore, it has a negative velocity and zero acceleration. This option is incorrect.
(B) In this case, the car is traveling in the - direction and increasing its speed. Therefore, it has a negative velocity and a positive acceleration. However, the given direction is not specified, and thus this option is not accurate.
(C) In this case, the car is traveling in the +x direction and increasing in speed. Therefore, it has a positive velocity and a positive acceleration. This option is incorrect.
(D) In this case, the car is traveling in the - direction and decreasing in speed. Therefore, it has a negative velocity and a positive acceleration. This option is correct.
(E) In this case, the car is traveling in the +x direction and decreasing in speed. Therefore, it has a positive velocity and a negative acceleration. This option is incorrect.
Therefore, Option D ( - direction decreasing in speed) is correct.
To know more about negative velocity and positive acceleration, refer here:
https://brainly.com/question/12015984#
#SPJ11
when a 2.75-kg fan, having blades 18.5 cm long, is turned off, its angular speed decreases uniformly from 10.0 rad/s to 6.30 rad/s in 5.00 s. (a) what is the magnitude of the angular acceleration of the fan?
The angular acceleration of the fan is 0.740 rad/s^2,
Angular acceleration which represents the rate at which the angular velocity changes over time. The unit used to measure angular acceleration is radians per square second (rad/s2), according to the International System of Units. The Greek alphabet symbol alpha (α) is used to denote angular acceleration.
To calculate the angular acceleration of the fan, the formula α = Δω/Δt is used. Here, α represents angular acceleration, Δω represents the change in angular speed, and Δt represents the change in time.
In this scenario, Δω is equal to 10.0 - 6.30 = 3.70 rad/s, and Δt is equal to 5.00 s. By substituting these values into the formula, we obtain α = 3.70/5.00 = 0.740 rad/s^2.
To gain more knowledge about angular acceleration, refer to brainly.com/question/21278452.
#SPJ11
An object starts at rest in position A on the track shown, then slides to position B. Friction acts on the object over the entire track. Which equation can you use to find the object's velocity at position B?
Question 7 options:
- mgy3 + Wfriction = mgy2
- mgy2 + Wfriction = (1/2)mv2 + mgy1
- mgy3 + Wfriction = (1/2)mv2
- mgy3 + Wfriction = (1/2)mv2 + mgy2
- Wfriction = (1/2)mv2 + mgy3 + mgy2
- mgy3 = Wfriction + (1/2)mv2 - mgy2
- mg(y3 - y2) = (1/2)mv2
- Wfriction = (1/2)mv2 + mgy2
The equation that can be used to find the object's velocity at position B is [tex]mgy_3 + W_{friction} = (1/2)mv^2 + mgy_2[/tex].
What is friction?Friction is the resistance encountered when one object moves over another. Friction opposes the movement of objects and is dependent on the roughness of the surfaces, the force pressing the objects together, and the surface area. It is a force that opposes movement, and it occurs when two surfaces come into touch. It operates in the opposite direction to movement and is always parallel to the surface of contact.
What is Velocity?Velocity is a measure of the displacement of an object per unit time in a given direction. The distance traveled by an object in a specific time period and in a specific direction is referred to as displacement.
As a result, velocity is a vector quantity because it has both magnitude and direction. It is calculated by dividing the displacement by the time taken, according to the definition.
Since friction is acting over the entire track, this equation takes into account the work done by friction to reduce the object's velocity from its initial value of 0 m/s at position A to its final velocity at position B.
Learn more about Friction here:
https://brainly.com/question/24338873
#SPJ11
Three identical conducting spheres are charged as follows. Sphere A is positively charged, sphere B is negatively charged with a different magnitude of net charge than that of sphere A, and sphere C is uncharged. Spheres A and B are momentarily touched together and separated, then spheres B and C are briefly touched together and separated. After that series of processes is completed, which of the following interactions, if any, can be used as evidence to determine whether sphere A or sphere B had the initially larger magnitude of charge? A Sphere C is repelled from sphere A. B Sphere C is repelled from sphere B. Sphere A is repelled from sphere B. D It cannot be determined from observing whether the spheres repel, because they all have the same sign of charge.
The answer is C. Sphere A is repelled from sphere B
Step by step explanation:
The question is asking which of the interactions between sphere A, B, and C can be used as evidence to determine which one had the initially larger magnitude of charge. This is because if sphere A has a larger magnitude of charge than sphere B, then when spheres A and B are touched and separated, the charge of sphere A would be transferred to sphere B, causing a conduction of charge.
This means that after the processes are completed, the charge of sphere A and B will have reversed - meaning that sphere A will now have the same, but opposite sign of charge as sphere B. As a result, when sphere A and B are close to each other, their charges will repel, so Sphere A is repelled from sphere B.
Learn more about "conduction and charge" at : https://brainly.com/question/893656
#SPJ11
A car has an intial velocity of 50 km hr after 5 h, its final velocity is 70 km hr. solve for the car acceleration
Answer:
4 km/hr^2
Explanation:
We can use the formula for acceleration:
a = (v_f - v_i) / t
where:
a = acceleration
v_f = final velocity
v_i = initial velocity
t = time taken
Substituting the given values, we get:
a = (70 km/hr - 50 km/hr) / 5 hr
a = 20 km/hr / 5 hr
a = 4 km/hr^2
Ceteris paribus, which of these events would cause both the equilibrium interest rate and the equilibrium quantity of investment to fall?
• A dcrease investor confidance
• A decrease in cosmetic income and wealth • A strengh of time preference
• A decrease in capital productivity
Ceteris paribus, a decrease in capital productivity is the event that would cause both the equilibrium interest rate and the equilibrium quantity of investment to fall. The correct answer is option C.
Ceteris paribus is a Latin expression that means "all other things being equal." Ceteris paribus is a model in which economists use to analyze the effect of one independent variable on a dependent variable while keeping all other independent variables constant. This implies that only one variable is allowed to change while all other variables are held constant at their current level or position.
Therefore, Ceteris paribus, an increase in investor confidence, an increase in cosmetic income and wealth, and a strength of time preference will not cause both the equilibrium interest rate and the equilibrium quantity of investment to fall. However, a decrease in capital productivity is an event that would cause both the equilibrium interest rate and the equilibrium quantity of investment to fall.
When capital productivity is low, firms are unable to produce goods and services efficiently, and as a result, the demand for investment falls. When the demand for investment falls, the equilibrium quantity of investment will also decrease, leading to a decrease in the equilibrium interest rate.
To know more about Ceteris paribus, refer here:
https://brainly.com/question/13864080#
#SPJ11
What two planets are coming together?
The two planets that are coming together are Saturn and Jupiter. On December 21st, 2020, the two planets will be at their closest point, an event known as the Great Conjunction.
To observe the Great Conjunction, look in the direction of the southwest sky shortly after sunset. The two planets will appear to be close together and will look like one bright star. Make sure to look for them with binoculars or a telescope if you can, as you'll get a better view.The Great Conjunction occurs because Saturn and Jupiter have different orbital periods. Jupiter completes its orbit around the Sun every 11.86 Earth years, while Saturn takes 29.5 Earth years. This means that their orbits don't intersect and they don't come this close together very often. The next time the two planets will come this close together will be in 2080, so be sure to take advantage of this rare opportunity to witness this event in 2020.For more questions on Great Conjunction
https://brainly.com/question/21950257
#SPJ11
three forces applied to a trunk that moves leftward by 3.010 m over a frictionless floor. The force magnitudes are F1 = 5.86 N, F2 = 9.180 N, and F3 = 3.850 N, and the indicated angle is θ = 67.8°. During the displacement, what is the net work done on the trunk by the three forces? (Note that there are other forces acting on the block, but we only care about the net work done by these three forces.) And by how much does the kinetic energy of the trunk increase (enter a positive value) or decrease (negative value)?
The kinetic energy of the trunk increases by ½ mvf² = ½ m(10.65 m/s)²= 71.44 J during the displacement.
Net work = ΔK
W = Fd cosθ
W1 = F1d cosθ = (5.86 N)(3.010 m) cos(67.8°) = 6.99 J
W2 = F2d cosθ = (9.180 N)(3.010 m) cos(67.8°) = 10.97 J
W3 = F3d cosθ = (3.850 N)(3.010 m) cos(67.8°) = 4.58 J
Net work = W1 + W2 + W3 = 6.99 J + 10.97 J + 4.58 J = 22.54 J
Therefore, the net work done on the trunk by the three forces is 22.54 J.
ΔK = ½ mvf² - ½ mvi²
Since the trunk moves a distance of 3.010 m and is initially at rest, we can use the equation:
vf² = 2ad
where a is the acceleration of the trunk, which is given by:
a = ΣF / m
where ΣF is the net force on the trunk, which we can find using:
ΣF = F1 + F2 + F3
ΣF = (5.86 N + 9.180 N + 3.850 N) = 18.89 N
Therefore, the acceleration of the trunk is:
a = ΣF / m = 18.89 N / m
Since the trunk moves leftward, the acceleration is also leftward, so we can use a negative value for a.
Substituting the values for a and d, we get:
vf² = -2(-18.89 N / m)(3.010 m) = 113.51 (m/s)²
Taking the square root, we get:
vf = 10.65 m/s
Therefore, the change in kinetic energy of the trunk is:
ΔK = ½ mvf² - ½ mvi² = ½ m(10.65 m/s)²- 0 = ½ mvf²
Kinetic energy is a type of energy that an object possesses by virtue of its motion. It is defined as the energy an object has due to its motion and is proportional to the mass of the object and the square of its velocity. The formula for kinetic energy is KE = 1/2mv^2, where m is the mass of the object and v is its velocity.
Kinetic energy is a scalar quantity and has units of joules in the International System of Units (SI). It is a fundamental concept in physics and is used to describe many physical phenomena, including the motion of particles, the behavior of gases, and the motion of waves. In many cases, kinetic energy can be transformed into other forms of energy. For example, when a ball is thrown upwards, its kinetic energy is gradually converted into gravitational potential energy as it moves higher and higher.
To learn more about Kinetic energy visit here:
brainly.com/question/26472013
#SPJ4
at what angle above the horizon is the sun when light reflecting off a smooth lake is polarized most strongly?
The sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.
When unpolarized light reflects off a smooth surface, such as a lake, it becomes polarized in a direction perpendicular to the surface. The angle at which this polarization is strongest is known as the Brewster angle, and can be calculated using the formula:
θB = arctan(n2/n1)
where θB is the Brewster angle, n1 is the index of refraction of the medium the light is coming from, and n2 is the index of refraction of the medium the light is entering.
For water, the index of refraction is approximately 1.33, and for air it is approximately 1.00. Plugging these values into the formula, we get:
θB = arctan(1.33/1.00) = 53.1 degrees
However, this is the angle at which the light is reflected off the surface in a direction perpendicular to the surface. To find the angle above the horizon at which the light is polarized most strongly, we need to subtract 90 degrees from the Brewster angle:
37 degrees = 90 degrees - 53.1 degrees
Therefore, the sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.
For more similar questions on Brewster angle:
brainly.com/question/29428422
#SPJ11
