Use the nuclear decay reaction in the picture to answer the following question.

i. How does the reaction demonstrate the laws of conservation of charge and conservation of nucleon number?


ii. What is the binding energy of one mole of atomic mass: 234, number of proton: 90, Thorium if the mass defect is 1.908 g/mol?

Answer:

Explanation:

Adding sugar

Answer:

[tex]V_2=583.3mL[/tex]

Explanation:

Hello,

In this case, for the given constant amount and pressure of the, we apply the Charles' law which allows us to understand the volume-pressure behavior as a directly proportional relationship:

[tex]\frac{V_1}{T_1} =\frac{V_2}{T_2}[/tex]

Thus, since we need to compute the volume after the temperature increase (which must be expressed in absolute Kelvins), we obtain V2 as:

[tex]V_2=\frac{V_1T_2}{T_1} =\frac{350.0mL*(227+273.15)K}{(27+273.15)K}\\ \\V_2=583.3mL[/tex]

Best regards.

Answer:

In the case of Mount Pinatubo, the result was a measurable cooling of the Earth's surface for a period of almost two years. Because they scatter and absorb incoming sunlight, aerosol particles exert a cooling effect on the Earth's surface.

Explanation:

Temperature measures the average kinetic energy of particles of the substances. Therefore, the Mt. Pinatubo eruption result in global temperatures dropping almost two degrees.

Temperature is used to measure degree or intensity of heat of a particular substance. Temperature is measured by an instrument called thermometer.

Temperature can be measured in degree Celsius °c, Kelvin k or in Fahrenheit. Temperature is a physical quantity. Heat always flow from higher temperature source to lower temperature source.

We can convert these units of temperature into one another. The relationship between degree Celsius and Fahrenheit can be expressed as:

°C={5(°F-32)}÷9

The Mt. Pinatubo eruption result in global temperatures dropping almost two degrees because they scatter and absorb incoming sunlight, aerosol particles exert a cooling effect on the Earth's temperature.

Therefore, the Mt. Pinatubo eruption result in global temperatures dropping almost two degrees.

To know more about temperature, here:

https://brainly.com/question/13694966

#SPJ6

Answer:

0.2M

Explanation:

Step 1:

Data obtained from the question.

Volume of acid (Va) = 100mL

Molarity of the acid (Ma) = 0.026 M

Volume of base (Vb) = 13mL

Molarity of the base (Mb) =..?

Step 2:

The balanced equation for the reaction. This is given below:

HCl + KOH —> KCl + H2O

From the balanced equation above,

The mole ratio of the acid (nA) = 1

The mole ratio of the base (nB) = 1

Step 3:

Determination of the molarity of the base, KOH. This can be obtained as follow:

MaVa/MbVb = nA/nB

0.026 x100 / Mb x 13 = 1

Cross multiply to express in linear form

Mb x 13 = 0.026 x 100

Divide both side by 13

Mb = 0.026 x 100 / 13

Mb = 0.2M

Therefore, the molarity of the base, KOH is 0.2M

Answer:

0.2M

Explanation:

KOH(aq) + HCl(aq) ⇒  KCl(aq) + H2O(l)

We express the moles of analyte (HCl) and titrant based (KOH) on their molar concentration:

M1 * V1 = M2 * V2

The molarity of the solution is calculated with the following equation:

M2 = V1 x M1 / ​​V2

Where:

V2 = valued sample volume

V1 = volume of titrant consumed (measured with the burette)

M1 = concentration of titrant solution

M2 = concentration of sample

M2 = 100mL * 0.026M / 13mL = 0.2M

Answer:

400 mL

Explanation:

Boyle's Law: [tex]P_1*V_1 = P_2*V_2[/tex]

Let x = the resulting volume

350 (200) = 700 (x)

x = 400 mL

Answer:

- 7 carbon atoms.

- 14 hydrogen atoms.

- 1 oxygen atom.

Explanation:

Hello,

In this case, for the given compound, heptanone, whose chemical formula is:

[tex]CH_3COCH_2CH_2CH_2CH_2CH_3[/tex]

We can write the molecular formula showing the present atoms of each element:

[tex]C_7H_{14}O[/tex]

In such a way we have:

- 7 carbon atoms.

- 14 hydrogen atoms.

- 1 oxygen atom.

Best regards.

Answer:

Explanation:

A crystal of table salt (NaCl) is dissolved in water. Which of the following statements explains why the dissolved salt does not recrystallize as long as the temperature and the amount of water stay constant?

Na+ and Cl- ions lose their charges in the water.

Water molecules surround the Na+ and Cl- ions.

Na+ and Cl- ions leave the water through vaporization.

Water molecules chemically react with the Na+ and Cl- ions.

Your answer: -

Answer: B - Water molecules surround the Na+ and Cl- ions.

Answer:

SO₂: 0.39atm

O₂: 3.645atm

Explanation:

Based on the reaction:

2 SO₂(g) + O₂(g) → 2 SO₃(g)

2 moles of sulfur dioxide react per mole of oxygen to produce 2 moles of sulfur trioxide.

When the reaction occurs an comes to equilbrium, the partial pressure of each gas is:

SO₂: 1.3atm - 2X

O₂: 4.1atm -X

SO₃: 2X

Where X is the reaction coordinate.

As pressure at equilibrium of SO₃ is 0.91 atm:

0.91atm = 2X

Thus: X = 0.455atm.

Replacing, pressures at equilibrium of the gases are:

SO₂: 1.3atm - 2×0.455atm = 0.39 atm

O₂: 4.1atm -0.455atm = 3.645 atm

Answer:

204g of NH3

Explanation:

The balanced equation for the reaction is given below:

N2 + 3H2 —> 2NH3

Next, we shall determine the number of mole NH3 produced by reacting 6moles of N2. This is illustrated below:

From the balanced equation above,

1 mole of N2 reacted to produce 2 moles of NH3.

Therefore, 6 moles of N2 will react to produce = 6 x 2 = 12 moles of NH3.

Finally, we shall convert 12 moles of NH3 to grams. This is illustrated below:

Number of mole of NH3 = 12 moles.

Molar mass of NH3 = 14 + (3x1) = 17g/mol

Mass of NH3 =..?

Mass = mole x molar mass

Mass of NH3 = 12 x 17

Mass of NH3 = 204g.

Therefore, 204g of NH3 will be produced from the reaction.

Answer:

A niche is more than a physical place; it's a species' role in a specific place and it can change from habitat to habitat.                  

Explanation:

Niche: In biology, the term "niche" is described as a process through which different organisms tends to fit-in into a specific ecosystem or an ecological community. However, a niche is considered as the "evolutionary result" of a specific species behavioral, morphological, and physiological adaptations associated with its surroundings.

Habitat: In biology, the term "habitat" is described as an environmental or ecological area that is being inhabited by a specific species of plants, animals, or other organisms.

Therefore, a niche is entirely different from a habitat because an organism's niche tends to explain every different aspect of its life whereas its habitat explains the place it lives.

Answer:

C. cooler than both the crust and the core

Explanation:

It is observed that at the mantle, temperatures range from estimatedly 200 °C (392 °F) around the upper boundary with the crust to approximately 4,000 °C (7,230 °F) at the core-mantle boundary.

So we can say the mantle is cooler than both the crust and the core.

Answer:

Metamorphic rocks are formed from pre-existing rock and sediment materials. They are formed when igneous, sedimentary, or other pre-existing metamorphic rocks are exposed to the heat and pressure as well as super-heated mineral-rich fluids. They are compacted together to form a new rock altogether. Metamorphism does not include the melting or liquefaction of the pre-existing rock. Instead, it compacts them and crushes them, pushing them together at extreme heat and pressure to form a new rock altogether composed of sedimentary, igneous, and other metamorphic rock. It's the rock hybrid of the geologic world.

Metamorphism is similar to when you squish playdough together, it doesn't form a new playdough color (unless you REALLY mixed that poor playdough together). It forms an amalgamation of different colors and patterns made from the other rock.

Taken from a paper I once wrote I explained this again:

"Metamorphic rocks are formed when pre-existing rocks and their minerals are compressed and altered by Earth’s internal processes; interior pressure, temperature (heat), and chemical reactions. The minerals and pre-existing rock necessary for the creation of metamorphic rock must then also be located deep underground if such processes are expected to make an impact and create a metamorphic rock."

Due to prokaryote

Explanation:

Answer:

1000 K

Explanation:

Given data

We can find the temperature of carbon dioxide using the ideal gas equation.

[tex]P \times V = n \times R \times T\\T = \frac{P \times V}{n \times R} = \frac{0.8210atm \times 50L}{0.5mol \times \frac{0.08206atm.L}{mol.K} }=1000 K[/tex]

The temperature of the gas is 1000 K.

Answer:

400 kPa

Explanation:

Please see the step-by-step solution in the picture attached below.

Hope this answer can help you. Have a nice day!

Answer:

400 kPa

The answer is right since its from ck12

Answer:

See explanation below

Explanation:

To do aflow diagram for extraction of these two components of a sample, we need to analize both reagents so we can make a great diagram and separate both reagents.

First, let's see the acid. The 2-chlorobenzoic acid is a relativel strong acid, so, in order to separate this from a sample we need to use a base to do so. However, it's very important the use of the base here, we cannot use any base to do it, for the main reason that the sample has other component, and this component may react too with the base and the separation will not be succesfull. So, as the chlorobenzoic acid is a relatively strong acid, if we use a strong base such as NaOH, this will react with the acid, but it will also react with the 1,4-dichlorobenzene forming a Sn2 product and a salt like this.

C₆H₄Cl₂ + NaOH ---------> C₆H₅OCl + NaCl

This is the reason which we cannot use NaOH, because it's a strong base that may react with other compounds in the sample.

To solve this, we can use a weak base such as NaHCO₃. This weak base has the strength enough to react with the benzoic acid, but not strong enough to react with the dichlorobenzene.

So, the first step is dissolve the sample in an organic solvent like ether. The next step is mixing the sample with NaHCO₃. This will cause the layer to divide into two layers. One aqueous layer that will have the product of the acid with the base, and an organic layer with the dichlobenzene. Afterward, we just need to use a strong acid like HCl, but dilluted in the aqueous layer to regenerate the acid, and in the organic layer, just heat the solution til the whole solvent evaporates completely.

The flow diagram is below in the attached picture.

Answer:

Specific Immune Response

Explanation:

A specific immune response identifies the pathogen which then allows it to produce antibodies that protect against that SPECIFIC pathogen.

Answer:

Explanation:

Answer:

Explanation:

N₂       + 3H₂     =     2 NH₃

1 vol                         2 vol

786 liters               1572 liters

786 liters of dinitrogen will result in the production of 1572 liters of ammonia

volume of ammonia V₁ = 1572 liters

temperature T₁ = 222 + 273 = 495 K

pressure = .35 atm

We shall find this volume at NTP

volume V₂ = ?

pressure = 1 atm

temperature T₂ = 273

[tex]\frac{P_1V_1}{T_1} =\frac{P_2V_2}{T_2}[/tex]

[tex]\frac{.35\times 1572}{495} =\frac{1\times V_2}{ 273 }[/tex]

[tex]V_2 =303.44[/tex] liter .

mol weight of ammonia = 17

At NTP mass of 22.4 liter of ammonia will have mass of 17 gm

mass of 303.44 liter of ammonia will be equal to (303.44 x 17) / 22.4 gm

= 230.28 gm

=.23 kg / sec .

Rate of production of ammonia = .23 kg /s .

Answer:

A chemical reaction is a process in which one or more substances, also called reactants, are converted to one or more different substances, known as products. ... A chemical reaction rearranges the constituent atoms of the reactants to create different substances as products.

Explanation:

Hopefully this is what you needed

Answer:

[tex]m_{NH_3}=4.25kgNH_3[/tex]

Explanation:

Hello,

In this case, for the production of ammonium nitrate we shall consider the following chemical reaction:

[tex]NH_3+HNO_3\rightarrow NH_4NO_3[/tex]

Hence, since the molar mass of ammonium nitrate is 80 g/mol and the molar mass of ammonia is 17 g/mol, we could compute the required mass of ammonia to produce 20 kg of ammonium nitrate  by using kilo-based units:

[tex]m_{NH_3}=20kgNH_4NO_3*\frac{1kmol}{80kgNH_4NO_3}*\frac{1kmolNH_3}{1kmolNH_4NO_3}*\frac{17kgNH_3}{1kmolNH_3} \\\\m_{NH_3}=4.25kgNH_3[/tex]

Best regards.

Answer:

.00352mol/L

Explanation:

molarity (concentration) = number of moles / volume of solvent (in L)

M = .99g / 56.108‬g/mol / .5L

M = .0176mol / .5L

M = .00352mol/L

Answer:

Check the explanation

Explanation:

1)

Atomic number of Se = 34

So, number of proton = 34

use:

charge = number of proton - number of electron

-2 = 34 - number of electron

number of electron = 36

number of neutron = mass number - atomic number

= 78 - 34

= 44

Answer:

44

34

36

2)

number of proton = mass number - number of neutron

= 65 - 36

= 29

29 is atomic number for Cu

use:

charge = number of proton - number of electron

+1 = 29 - number of electron

number of electron = 28

Answer:

Cu

29

28

3)

Atomic number is 36 for Kr

use:

charge = number of proton - number of electron

= 36 - 36

= 0

use:

mass number = number of proton + number of neutron

= 36 + 42

= 78

Answer:

Kr

78

0

Answer:

127 grams of carbon dioxide

Explanation:

We need to determine the chemical equation first. Butane has a chemical formula of [tex]C_4H_{10}[/tex], oxygen is [tex]O_2[/tex], carbon dioxide is [tex]CO_2[/tex], and water is [tex]H_2O[/tex]. The reactants are butane and oxygen and the products are carbon dioxide and water. So we write:

[tex]C_4H_{10}+O_2[/tex] ⇒ [tex]CO_2+H_2O[/tex]

But remember! We need to balance this. Currently, there are 4 carbon atoms (C), 10 hydrogen atoms (H), and 2 oxygen atoms (O) on the left, while there are 1 carbon atom (C), 2 hydrogen atoms (H), and 3 oxygen atoms (O) on the right. Let's place a coefficient of 4 in front of the carbon dioxide and a coefficient of 5 on the water, so that we have equal numbers of carbon and hydrogen atoms on each side:

[tex]C_4H_{10}+O_2[/tex] ⇒ [tex]4CO_2+5H_2O[/tex]

However, we need to ensure that there are equal numbers of O atoms, as well. On the left, we have 2 and on the right we have 13, so let's put a coefficient of 6.5 on the oxygen:

[tex]C_4H_{10}+6.5O_2[/tex] ⇒ [tex]4CO_2+5H_2O[/tex]

Finally, multiply everything by 2 to get whole number coefficients:

[tex]2C_4H_{10}+13O_2[/tex] ⇒ [tex]8CO_2+10H_2O[/tex]

Ah, now we can actually get to the problem!

We need to determine the limiting reactant, so let's convert the 42 g of butane and 150 g of oxygen into moles of any product, say, carbon dioxide. To convert to moles, we need to find the molar mass of each compound.

The molar mass of butane is 4 * 12.01 + 10 * 1.01 = 58.14 g/mol, while the molar mass of oxygen is 2 * 16 = 32 g/mol. We can now set up the equations:

[tex]42 gC_4H_{10}*\frac{1molC_4H_{10}}{58.14gC_4H_{10}} *\frac{8molCO_2}{2molC_4H_{10}} =2.8896molCO_2[/tex]

[tex]150 gO_2*\frac{1molO_2}{32gO_2} *\frac{8molCO_2}{13molO_2} =2.8846molCO_2[/tex]

Clearly, we see that 2.8846 < 2.8896, which means that oxygen is the limiting reactant. In other words, the most products can be made when the oxygen is all used up.

Now let's finally convert moles of carbon dioxide into grams by multiplying by its molar mass, which is 12.01 + 2 * 16 = 44.01 g/mol:

[tex]2.8846molCO_2*\frac{44.01gCO_2}{1molCO_2} =127gCO_2[/tex]

Notice that we have 3 significant figures because we had 3 significant figures at the start with 150. grams of oxygen.

~ an aesthetics lover

Answer:

The correct answer is 7.8 percent.

Explanation:

As mentioned in the given question, the absorbance (A) of the sample solution is 1.07. To find the concentration of aspirin, Beer's law is used, that is, A = ebc

Here, e is the extinction coefficient, which is equal to 139.322 M^-1cm^-1 as per the standard value for salicylic acid, b is the pathlength, which is equivalent to 1 cm. Now putting the values we get,  

A = ebc

c = A / (eb)

c = 1.07 / (139.322 × 1)

c = 0.00768 M

Now to determine the percent salicylic acid in the sample, there is a need to compare the value of concentration determined with the concentration of aspirin given initially.  

0.02 grams is the initial concentration of aspirin mentioned in the question. The molar mass of aspirin is 240 g/mol.  

Therefore, the moles of aspirin will be,  

0.02 / 240 = 8.33 × 10^-5 moles  

The final volume of the diluted solution given is 10 ml or 0.01 liters.  

The molarity of aspirin in the diluted solution will be,  

c1 = 8.33 × 10^-5 / 0.01 = 8.33 × 10^-3 M or 0.00833 M

Now, the percent of salicylic acid in the product will be,  

c1 - c / c1 × 100

(0.00833 - 0.00768) / 0.00833 × 100 = 7.8 %

Absorbance is directly proportional to the concentration of the solution. The absorbance can be calculated if the molar absorptivity, path length, and concentration of the absorbing species are known.

The percent of salicylic acid in the solution is 7.8%

Given that:

Absorbance of the solution is = 1.07

Path length = 1 cm.

Applying Beer's Law,

A = ε b c

where,

c = concentration, A = absorbance, ε = constant, and b = path length

Now, putting the values in above equation

c = [tex]\dfrac{\text{A}}{\text {(e b)}}[/tex]

c = [tex]\dfrac{1.07}{139.32 \times 1}[/tex]        ( ε = 139.32)

c = 0.00768 M

Now, to calculate the percent of the salicylic acid in the solution, we will compare the given concentration of the aspirin.

As we know:

Given mass of aspirin = 0.02 g

Molar mass of aspririn = 240

Number of moles of aspirin = 0.02 / 240 = 8.33 x 10⁻⁵

Now, the molarity of aspirin is:

[tex]\text{Molarity}&= \dfrac{8.33 \times 10^{-5}}{0.01}\\\\\text{Molarity}&= 8.33 \times 10^{-5}[/tex]

Now, the percent of the salicylic acid is:

[tex]\dfrac{\text {C}_1 - \text C}{\text {C}_1 \times 100}[/tex]

[tex]\dfrac{(0.00833 - 0.00768)}{0.00833 \times 100}[/tex]

Percent of Salicyclic acid = 7.8%.

Thus, the percentage of the salicylic acid in the given solution is 7.8%.

To know more about Absorbance, refer to the following link:

https://brainly.com/question/17062521

Answer:

The results will be similar.

Answer:

D) 7.5 grams

Explanation:

Hello,

In this case, since the percent yield is defined by:

[tex]Y=\frac{m^{actual}}{m^{theoretical}} *100\%[/tex]

In such a way, since the percent yield is up to 25% and the expected or theoretical amount is 30 g of the product, the actual yield of the reaction is:

[tex]m^{actual}=\frac{Y*m^{theoretical}}{100\%} =\frac{25\%*30g}{100\%} \\\\m^{actual}=7.5g[/tex]

Therefore the answer is D) 7.5 grams.

Best regards.