Explanation:
False, it is oppisite the shorter the wavelength the more energy it carries.
A person pushes down on a lever with a force of 100 N. At the other end of the lever, a force of 200 N lifts a heavy object. What is the mechanical advantage of the lever?
A. 1/2, because the object will be lifted half the distance
B. -1, because the direction changes
C. 2, because the output force is twice the input force
D. 1, because the same amount of work is done
Answer:
Explanation:
C 200÷100=2
Output ÷ Input= MA
If there is "waste" energy, does the Law of Conservation of Energy still apply?
Explanation:
Yes, the law of conservation of energy still applies even if there is waste energy.
The waste energy are the transformation products of energy from one form to another.
According to the law of conservation of energy "energy is neither created nor destroyed by transformed from one form to another in a system".
But of then times, energy is lost as heat or sound within a system.
If we take into account these waste energy, we can see that energy is indeed conserved. The sum total of the energy generated and those produced will be the same if we factor in other forms in which the energy has been transformed into."45 meters north" is an example of
Answer:
Displacement
Explanation:
The quantity 45m north is a typical example of displacement.
Displacement is the distance traveled by a body in a specific direction. Displacement is a vector quantity with both magnitude and direction.
When we are specifying the displacement of a body, the direction must be indicated accurately. Therefore, the quantity given is displacementTwo metal bricks are held off the edge of a balcony from the same height above the ground. The bricks are the same size but one is made of Titanium (density of 4.5 g/cm%) and one is made of Lead (density of 11.3 g/cm3) so the Lead is about twice as heavy as the Titanium. The time it takes the bricks to reach the ground will be:________.
a. less but not necessarily half as long for the heavier brick
b. about half as long for the lighter brick
c. less but not necessarily half as long for the lighter brick
d. about half as long for the heavier brick
e. about the same time for both bricks
Answer:
e.
Explanation:
Assuming that the air resistance is neglectable, both bricks are only accelerated by gravity, which produces a constant acceleration on both bricks, which is the same, according Newton's 2nd Law, as we can see below:[tex]F_{g} = m*g = m*a (1)[/tex]⇒a = g = 9.8m/s² (pointing downward)Since acceleration is constant, if both fall from the same height, we can apply the following kinematic equation:[tex]\Delta y = v_{o} * t - \frac{1}{2} *g*t^{2} (2)[/tex]
Since both bricks are held off the edge, the initial speed is zero, so (2) reduces to the following equation:[tex]h =\frac{1}{2} *g*t^{2} (3)[/tex]
Since h (the height of the balcony) is the same, we conclude that both bricks hit ground at exactly the same time.If the air resistance is not negligible, due both bricks have zero initial speed, and have the same shape, they will be affected by the drag force in similar way, so they will reach the ground at approximately the same time.Which of the physical variables listed below will change when you change the area of the capacitor plates (while keeping the battery connected).
a. Capacitance
b. Charge on the plates
c. Voltage across the plates
d. Net electric field between the plates
e. Energy stored in the capacitor
Answer:
a. Capacitance
b. Charge on the plates
e. Energy stored in the capacitor
Explanation:
Let A be the area of the capacitor plate
The capacitance of a capacitor is given as;
[tex]C = \frac{Q}{V} = \frac{\epsilon _0 A}{d} \\\\[/tex]
where;
V is the potential difference between the plates
The charge on the plates is given as;
[tex]Q = \frac{V\epsilon _0 A}{d}[/tex]
The energy stored in the capacitor is given as;
[tex]E = \frac{1}{2} CV^2\\\\E = \frac{1}{2} (\frac{\epsilon _0 A}{d} )V^2[/tex]
Thus, the physical variables listed that will change include;
a. Capacitance
b. Charge on the plates
e. Energy stored in the capacitor
A vertical piston-cylinder device contains a gas at a pressure of 100 kPa. The piston has a mass of 10 kg and a diameter for 14 cm. Pressure of the gas is to be increased by placing some weights on the piston. Determine the local atmospheric pressure and the mass of the weights that will doublethe pressure of the gas inside the cylinder.
Answer:
the local atmospheric pressure is 93.63 kPa
the mass of the weights is 156.9 kg
Explanation:
Given that;
Initial pressure of gas = 100 kPa
mass of piston = 10 kg and diameter = 14 cm = 0.14 m
g = 9.81 m/s²
Now,
P_gas = P_atm + P_piston
100 = P_atm + P_piston --------- let this equation 1
P_piston = M_piston × g / A = (10 × 9.81) / π/4×d²
P_piston = 98.1 / (π/4×( 0.14 )²)
P_piston = 98.1 / 0.01539 = 6374,269 Pa = 6.37 kPa
now, from equation 1
100 = P_atm + P_piston
we substitute
100 = P_atm + 6.37
P_atm = 100 - 6.37
P_atm = 93.63 kPa
Therefore, the local atmospheric pressure is 93.63 kPa
Now for pressure of the gas in the cylinder ⇒ 2×initial pressure
Pgas_2 = 2 × 100 = 200 kPa
Pgas_2 = P_atm + P_piston + P_weight
Pgas_2 = P_gas + P_weight
we substitute
200 kPa = 100 kPa + P_weight
P_weight = 200 kPa - 100 kPa
P_weight = 100 kPa = 100,000 Pa
Also;
P_weight = M×g / A
100,000 Pa = ( M × 9.81 ) / (π/4 × (0.14)²)
100,000 × 0.01539 = M × 9.81
1539 = M × 9.81
M = 1539 / 9.81
M = 156.9 kg
Therefore, the mass of the weights is 156.9 kg
As waves crash into rock along the shoreline, particles of sand, shell, and other materials in the ocean water loosen tiny bits of sediment from the rock. As the waves recede, they carry the sediment away. In this scenario, which process represents weathering, and which process represents erosion?
Answer:
WEATHERING is represented by the scenario (As waves crash into rock along the shoreline, particles of sand, shell, and other materials in the ocean water loosen tiny bits of sediment from the rock).
Erosion is represented by the scenario (As the waves recede, they carry the sediment away).
Explanation:
A wave is a disturbance which travels through a medium and transfers energy from one point to another. When wind blows over a water body like the ocean, ocean waves are formed. As the generated energy from the wind is transported through the water by the waves, the can hit against rocks on the shores leading to its break down with time. WEATHERING occurs when tiny bit of sediments from rocks are loosened due to the impact of ocean waves.
Erosion can be described as the wearing away of the earth's surface due to the impact of wind, rainfall ( water) or waves. There are different types of erosion which is classified according it's cause of formation.
Wave erosion occurs when sediments such as sand, shell and other materials are carried to the shoreline by ocean waves. This erodes the shore over time as the sediments act like sandpapers.
Car À moves at a speed of 8m/s for 43 seconds. Car B moves at a speed of 7 m/s for 50 seconds. Which car traveled a longer distance
Please show working
Distance = (speed) x (time)
Car A: Distance = (8 m/s) x (43 s) = 344 meters
Car B: Distance = (7 m/s) x (50 s) = 350 meters
350 meters is a longer distance than 344 meters.
Car-B traveled a longer distance than Car-A did.
Answer:
[tex]\boxed {\boxed {\sf Car \ B : 350 \ meters }}[/tex]
Explanation:
Distance is equal to the product of speed and time.
[tex]d=s*t[/tex]
1. Car A
Car A has a speed of 8 meters per second and travels for 43 seconds.
[tex]s= 8 \ m/s \\t= 43 \ s[/tex]
Substitute the values into the formula.
[tex]d= 8 \ m/s *43 \ s[/tex]
Multiply and note that the seconds will cancel out.
[tex]d= 8 \ m*43= 344 \ m[/tex]
2. Car B
Car B has a speed of 7 meters per second and travels for 50 seconds.
[tex]s= 7 \ m/s \\t= 50 \ s[/tex]
Substitute the values in and multiply.
[tex]d= 7 \ m/s * 50 \ s[/tex]
[tex]d= 7 \ m * 50 = 350 \ m[/tex]
350 meters is a longer distance than 344 meters, so Car B traveled the longer distance.
A mass m is gently placed on the end of a freely hanging spring. The mass then falls 33 cm before it stops and begins to rise. What is the frequency of the oscillation
Answer:
Explanation:
The mass falls by .33 m before it begins to rise . At that point loss of potential energy is equal to gain of elastic energy .
1/2 k x² = mgx
.5 x k x .33² = m x 9.8 x .33
k / m = 59.4
frequency of oscillation = [tex]\frac{1}{2\pi} \times\sqrt{\frac{k}{m} }[/tex]
= [tex]\frac{1}{2\pi} \times\sqrt{59.4}[/tex]
= 1.22 per second .
Consider a swimmer that swims a complete round-trip lap of a 50 m long pool in 100 seconds. The swimmer's... average speed is 0 m/s and average velocity is 0 m/s. average speed is 0.5 m/s and average velocity is 0.5 m/s. average speed is 1 m/s and average velocity is 0 m/s. average speed is 0 m/s and average velocity is 1 m/s.What is the swimmers average speed and average velocity?
Answer:
average speed is 1 m/s and average velocity is 0 m/s.
Explanation:
Given that :
Length of round trip = 50 m
Time taken = 100 seconds
The average speed :
Total distance / total time taken
Length of complete round trip :
(50 + 50) m, total. Distance = 100 m
100 / 100 = 1m/s
The average velocity :
Total Displacement / total time taken
Total Displacement of round trip = end point - start point = 0
0 / 100 = 0
Average speed is 1 m/s and average velocity is 0 m/s.
The average speed is defined as the ratio of distance to time. Speed is a scalar quantity hence it does not take direction into account while velocity is a vector quantity hence it takes direction into account.
The speed is obtained from;
Speed = Distance/time = 2(50 m)/100 s = 1 m/s.
The velocity is 0 m/s since it is complete round-trip lap.
Learn more about speed: https://brainly.com/question/7359669
A sinusoidal wave is traveling on a string with speed 19.3 cm/s. The displacement of the particles of the string at x = 6.0 cm is found to vary with time according to the equation y = (2.6 cm) sin[1.8 - (5.8 s-1)t]. The linear density of the string is 5.0 g/cm. What are (a) the frequency and (b) the wavelength of the wave? If the wave equation is of the form
Answer:
Explanation:
equation of wave is given by the following equation
y = (2.6 cm) sin[1.8 - (5.8 s-1)t].
Comparing it with standard form of wave
y = A sin ( ωt - kx )
we get
ω = 5.8
2πn = 5.8
n = .92 per second
kx = 1.8
k x 6 = 1.8
k = 0.3
[tex]\frac{2\pi}{\lambda}[/tex] = 0.3
λ = 20.9 cm
One disadvantage to experimental research is that experimental conditions do not always reflect reality.
Please select the best answer from the choices provided
T
F
Answer:
It's true I took the test on Edge.
Explanation:
Answer:
True
Explanation:
Got it right on edg
When the bowling ball has fallen halfway down the building (height = 20 m), it has a speed of 19.8 m/s.
How much potential energy does the bowling ball have?
How much kinetic energy does the bowling ball have?
How much total energy (potential + kinetic) does the bowling ball have?
Of the bowling ball’s total energy, is more in the form of potential or kinetic energy?
Answer:
I think the answer is 19.8 potential energy
Explanation:
NONE.
An 8.00 kg mass moving east at 15.4 m/s on a frictionless horizontal surface collides with a 10.0 kg object that is initially at rest. After the collision, the 8.00 kg object moves south at 3.90 m/s. (a) What is the velocity of the 10.0 kg object after the collision
Answer:
9.3m/s
Explanation:
Based on the law of conservation of momentum
Sum of momentum before collision = sum of momentum after collision
m1u1 +m2u2 = m1v1+m2v2
m1 = 8kg
u1 = 15.4m/s
m2 = 10kg
u2 = 0m/s(at rest)
v1 = 3.9m/s
Required
v2.
Substitute
8(15.4)+10(0) = 8(3.9)+10v2
123.2=31.2+10v2
123.2-31.2 = 10v2
92 = 10v2
v2 = 92/10
v2 = 9.2m/s
Hence the velocity of the 10.0 kg object after the collision is 9.2m/s
An RC car is carrying a tiny slingshot with a spring constant of 85 N/m at 0.2 m off the ground at 5.6 m/s. The sling shot is pulled back 3.5 cm from a relaxed state and shoots a 25 g steel pellet in the same direction the car is moving. What is the velocity of the steel pellet relative to the ground as it leaves the sling shot
Answer:
The velocity of the steel pellet relative to the ground when it leaves the sling shot is approximately 5.960 meters per second.
Explanation:
Let suppose that RC car-slingshot-steelpellet is a conservative system, that is, that non-conservative forces (i.e. friction, air viscosity) can be neglected. The velocity of the steel pellet can be found by means of the Principle of Energy Conservation and under the consideration that change in gravitational potential energy is negligible and that the RC car travels at constant velocity:
[tex]\frac{1}{2}\cdot (m_{C}+m_{P})\cdot v_{o}^{2} + \frac{1}{2}\cdot k\cdot x^{2} = \frac{1}{2}\cdot m_{C}\cdot v_{o}^{2} + \frac{1}{2}\cdot m_{P}\cdot v^{2}[/tex]
[tex]\frac{1}{2}\cdot m_{P}\cdot v_{o}^{2} + \frac{1}{2}\cdot k\cdot x^{2} = \frac{1}{2}\cdot m_{P}\cdot v^{2}[/tex]
[tex]m_{P}\cdot v_{o}^{2} + k\cdot x^{2} = m_{P}\cdot v^{2}[/tex]
[tex]v^{2} = v_{o}^{2} + \frac{k}{m_{P}}\cdot x^{2}[/tex]
[tex]v = \sqrt{v_{o}^{2}+\frac{k}{m_{P}}\cdot x^{2} }[/tex] (1)
Where:
[tex]v_{o}[/tex] - Initial velocity of the steel pellet, measured in meters per second.
[tex]v[/tex] - Final velocity of the steel pellet, measured in meters per second.
[tex]k[/tex] - Spring constant, measured in newtons per meter.
[tex]m_{P}[/tex] - Mass of the steel pellet, measured in kilograms.
[tex]m_{C}[/tex] - Mass of the RC car, measured in kilograms.
[tex]x[/tex] - Initial deformation of the spring, measured in meters.
If we know that [tex]v_{o} = 5.6\,\frac{m}{s}[/tex], [tex]k = 85\,\frac{N}{m}[/tex], [tex]m_{P} = 0.025\,kg[/tex] and [tex]x = 0.035\,m[/tex], then the velocity of the steel pellet relative to the ground when it leaves the sling shot is:
[tex]v = \sqrt{\left(5.6\,\frac{m}{s} \right)^{2}+\frac{\left(85\,\frac{N}{m} \right)\cdot (0.035\,m)^{2}}{0.025\,kg} }[/tex]
[tex]v \approx 5.960\,\frac{m}{s}[/tex]
The velocity of the steel pellet relative to the ground when it leaves the sling shot is approximately 5.960 meters per second.
It has been argued that power plants should make use of off-peak hours (such as late at night) to generate mechanical energy and store it until it is needed during peak load times, such as the middle of the day. One suggestion has been to store the energy in large flywheels spinning on nearly frictionless ball-bearings. Consider a flywheel made of iron, with a density of 7800 kg/m^3 , in the shape of a uniform disk with a thickness of 11.3 cm.
Required:
a. What would the diameter of such a disk need to be if it is to store an amount of kinetic energy of 14.1 MJ when spinning at an angular velocity of 93.0 rpm about an axis perpendicular to the disk at its center?
b. What would be the centripetal acceleration of a point on its rim when spinning at this rate?
Answer:
Explanation:
kinetic energy = 14.1 MJ = 14.1 x 10⁶ J
Let radius of flywheel be r .
volume of flywheel = π r² x t where t is thickness
= 3.14 x r² x .113 m³
= .04 r² m³
mass = volume x density
= .04 r² x 7800 = 312.73 r²kg
moment of inertia I = 1 / 2 mass x radius²
= .5 x 312.73 r² x r²
= 156.37 r⁴ kg m²
angular velocity ω = 2π x 93/60
= 9.734 rad /s
kinetic energy = 1/2 Iω² where ω is angular velocity
= .5 x 156.37 r⁴ x 9.734²
= 7408.08 r⁴
Given
7408.08 r⁴ = 14.1 x 10⁶
r⁴ = .19 x 10⁴
r = .66 x 10
= 6.60 m .
Diameter = 13.2 m
b )
centripetal acceleration of a point on its rim = ω² r
= 9.734² x 6.6
= 625.35 m /s²
take a picture of an object in your house, describe the
energy stores and transfers that happen with it. You can be as imaginative as you wish
with the object (choose something unusual), but the stores you identify and transfers
that happen must be real.
pls give me ideas of what to take a photo of for this I'm really stuck :(
what is the direction of the third force that would cause the box to remain stationary on the ramp ?
An arrow pointing from the bottom of the ramp to the top, I assume it would be friction.
Two children, each with a mass of 25.4 kg, are at fixed locations on a merry-go-round (a disk that spins about an axis perpendicular to the disk and through its center). One child is 0.78 m from the center of the merry-go-round, and the other is near the outer edge, 3.14 m from the center. With the merry-go-round rotating at a constant angular speed, the child near the edge is moving with translational speed of 11.5 m/s.
a. What is the angular speed of each child?
b. Through what angular distance does each child move in 5.0 s?
c. Through what distance in meters does each child move in 5.0 s?
d. What is the centripetal force experienced by each child as he or she holds on?
e. Which child has a more difficult time holding on?
Answer:
a) ω₁ = ω₂ = 3.7 rad/sec
b) Δθ₁ = Δθ₂ = 18.5 rad
c) d₁ = 14.5 m d₂ = 57.5 m
d) Fc1 = 273.9 N Fc2 = 1069.8 N
e) The boy near the outer edge.
Explanation:
a)
Since the merry-go-round is a rigid body, any point on it rotates at the same angular speed.However, linear speeds of points at different distances from the center, are different.Applying the definition of angular velocity, and the definition of angle, we can write the following relationship between the angular and linear speeds:[tex]v = \omega*r (1)[/tex]
Since we know the value of v for the child near the outer edge, and the value of r for this point, we can find the value of the angular speed, as follows:[tex]\omega = \frac{v_{out} }{r_{out} } = \frac{11.5m/s}{3.14m} = 3.7 rad/sec (2)[/tex]
As we have already said, ωout = ωin = 3.7 rad/secb)
Since the angular speed is the same for both childs, the angle rotated in the same time, will be the same for both also.Applying the definition of angular speed, as the rate of change of the angle rotated with respect to time, we can find the angle rotated (in radians) as follows:[tex]\Delta \theta = \omega * t = 3.7 rad/sec* 5.0 sec = 18.5 rad (3)[/tex]⇒ Δθ₁ = Δθ₂ = 18.5 rad.
c)
The linear distance traveled by each child, will be related with the linear speed of them.Knowing the value of the angular speed, and the distance from each boy to the center, we can apply (1) in order to get the linear speeds, as follows:[tex]v_{inn} = \omega * r_{inn} = 3.7 rad/sec * 0.78 m = 2.9 m/s (4)[/tex]
vout is a given of the problem ⇒ vout = 11. 5 m/s
Applying the definition of linear velocity, we can find the distance traveled by each child, as follows:[tex]d_{inn} = v_{inn} * t = 2.9m/s* 5.0 s = 14.5 m (5)[/tex]
[tex]d_{out} = v_{out} * t = 11.5 m/s* 5.0 s = 57.5 m (6)[/tex]
d)
The centripetal force experienced by each child is the force that keeps them on a circular movement, and can be written as follows:[tex]F_{c} = m*\frac{v^{2}}{r} (7)[/tex]
Replacing by the values of vin and rin, since m is a given, we can find Fcin (the force on the boy closer to the center) as follows:[tex]F_{cin} = m*\frac{v_{in}^{2}}{r_{in}} = 25.4 kg* \frac{(2.9m/s)^{2} }{0.78m} = 273.9 N (8)[/tex]
In the same way, we get Fcout (the force on the boy near the outer edge):[tex]F_{cout} = m*\frac{v_{out}^{2}}{r_{out}} = 25.4 kg* \frac{(11.5m/s)^{2} }{3.14m} = 1069.8 N (9)[/tex]
e)
The centripetal force that keeps the boys in a circular movement, is not a different type of force, and in this case, is given by the static friction force.The maximum friction force is given by the product of the coefficient of static friction times the normal force.Since the boys are not accelerated in the vertical direction, the normal force is equal and opposite to the force due to gravity, which is the weight.As both boys have the same mass, the normal force is also equal.This means that for both childs, the maximum possible static friction force, is the same, and given by the following expression:[tex]F_{frs} = \mu_{s} * m* g (10)[/tex]If this force is greater than the centripetal force, the boy will be able to hold on.So, as the centripetal force is greater for the boy close to the outer edge, he will have a more difficult time holding on.A stone is dropped from the top of a high cliff with zero initial velocity. In which system is the net momentum zero as the stone falls freely
Answer:
A system that includes the stone and the earth.
Explanation:
If the system of being dropped from the height of the cliff consists of just the stone alone, then it means that its momentum will certainly undergo changes as it falls freely. However, If the system is now expanded to include not only the stone but also the Earth, then it implies that the momentum of the stone which is in the downward direction will be equal and opposite to the momentum of the Earth in the upwards direction towards the stone. Therefore, the momentum will cancel out and net momentum will be zero.
A system of stone and earth can result to a net zero momentum.
Conservation of linear momentum
The principle of conservation of linear momentum states that the sum of the initial momentum is equal to the sum of final momentum.
[tex]m_1u_1 + m_2 u_2 = m_1v_1 + m_2 v_2[/tex]
A system that consists a linear system of stone and earth can result to a net zero momentum.
Thus, a system of stone and earth can result to a net zero momentum.
Learn more about conservation of momentum here: https://brainly.com/question/7538238
a wooden block is cut into two pieces, one with three times the mass of the other. a depression is made in both faces of the cut so that a fire cracker can be placed in it and the block is reassembled. the reassembled block is set on rough surface and the fuse is lit. when the fire cracker explodes, the two blocks separate. what is the ratio of distances traveled by blocks?
Answer:
1/9
Explanation:
Let A denote the bigger piece and let B denote the smaller piece.
We are told that one with three times the mass of the other.
Therefore, we have;
M_a = 3M_b
Firecracker is placed in the block and it explodes and thus, momentum is conserved.
Thus;
V_ai = V_bi = 0
Where V_ai is initial velocity of piece A and V_bi is initial velocity of piece B.
Since initial momentum equals final momentum, we have;
P_i = P_f
Thus;
0 = (M_a × V_af) + (M_b × V_bf)
Since M_a = 3M_b, we have;
(3M_b × V_af) + (M_b × Vbf) = 0
Making V_af the subject, we have;
V_af = -⅓V_bf
The kinetic energy gained by each block during the explosion will later be lost due to the negative work done by friction. Thus;
W_f = -½M_b•(v_bf)²
Now, let's express the work is in terms of the force and the distance.
Thus;
W_f = F_f × Δx × cos 180°
Frictional force is also expressed as μmg
Thus;
W_f = -μM_b × g × Δx
Earlier, we saw that;
W_f = -½M_b•(v_bf)²
Thus;
-½M_b•(v_bf)²= -μM_b × g × Δx
Δx = (v_bf)²/2μg
Let the distance travelled by block A be Δx_a and that travelled by B be Δx_b
Thus;
Δx_a/Δx_b = ((v_ba)²/2μg)/((v_bf)²/2μg)
Δx_a/Δx_b = ((v_af)²/((v_bf)²)
Δx_a/Δx_b = (-⅓V_bf)²/(V_bf)²
Δx_a/Δx_b = 1/9
What Coulombs discovered almost 300
years ago
Answer:
ummm hehe this is my time to shine
Explanation:
MERICIA!!!!!!!!!!!!!!!!!!!!!!!
Which of the following is a mixture?
a air
biron
Chydrogen
d nickel
Answer:
it will option option A hope it helps
One of the disadvantages of experimental research is that __________.
A.
it isn’t easily replicated
B.
it doesn’t often reflect reality
C.
the results aren’t generalizable
D.
conditions are not controllable
Please select the best answer from the choices provided
Answer:
B
Explanation:
What kind of scattering (Rayleigh, Mie, or non-selective) would you expect to be most important when radiation of the specified wavelength encounters the following natural or anthropogenic particles?
Slides 16-31, Lecture 2 ought to help - slides 19, 24, and 31 are key.
Wavelength O2 molecules Smoke particles Cloud droplets Rain droplets
(size 10^-10 m) (size 0.3 (μm) (20 μm) (size 3 mm)
550 nm
11 μm
1600 nm
1 cm
Solution :
1. Rayleigh scattering takes place when the particle size is smaller than the wavelength (λ).
2. Mie scattering takes place when particle size is nearly equal to the wavelength (λ).
3. Non-selective scatter takes place when particle size in greater than the wavelength (λ).
We have the sizes of different particles :
[tex]$O_2 \rightarrow 10^{10} \ m $[/tex]
Smoke particles [tex]$\rightarrow 3 \times 10^{-7} \ m$[/tex]
Cloud droplets [tex]$\rightarrow 2 \times 10^{-5} \ m$[/tex]
Rain droplets [tex]$\rightarrow 3 \times 10^{-3} \ m$[/tex]
Wavelength [tex]$ O_2 $[/tex] Smoke particles Cloud droplets Rain droplets
[tex]$10^{-10} \ m$[/tex] [tex]$ 3 \times 10^{-7} \ m$[/tex] [tex]$ 2 \times 10^{-5} \ m$[/tex] [tex]$ 3 \times 10^{-3} \ m$[/tex]
[tex]$5500 \times 10^{-4} \ m$[/tex] Rayleigh Non-selective Non-selective Non-selective
[tex]$11 \times 10^{-6} \ m $[/tex] Rayleigh Rayleigh Non-selective Non-selective
[tex]$1600 \times 10^{-10} \ m $[/tex] Rayleigh Non-selective Non-selective Non-selective
[tex]$10^{-2} \ m $[/tex] Rayleigh Rayleigh Rayleigh Mie
A truck travelling down the street suddenly brakes, applying a 14 N force over 3.5 seconds. What was the impulse over the given time.
Answer:
49 Ns
Explanation:
Given data
Force= 14N
time = 3.5seconds
Applying the expression for impulse
P= Ft
substitute
P=14*3.5
P=49 Ns
Hence the impulse is 49 Ns
How could a change in straight line motion due to unbalanced forces be predicted from an understanding of inertia?
Answer:
If the force goes in the direction of movement, the speed must increase and if the net force goes in the opposite direction, the speed must decrease.
Explanation:
The principle of inertia or Newton's first law states that every body remains static or with constant velocity if there is no net force acting on it.
Based on this principle, if we have a net force, the velocity of the body changes by having an unbalanced force acting.
If the force goes in the direction of movement, the speed must increase and if the net force goes in the opposite direction, the speed must decrease.
In which number are the zeros not significant?
100.0
O 0.0003
O 4.00005
O 1.0004
Answer:
0.0003
Explanation:
In the rules of Sig Figs, all zeros before with decimals are not sigificant. I.E. 0.00000000000000009. Despite how many 0's there are, only the 9 is significant. Zeros before a number is not significant. In 100, only the one is signficant in 100. with a dot at the end, the one and the two zeros are significant. hope this helps.
Answers:
the second option
Explanation:
A 500 kg wrecking ball is knocking down a wall. When it is pulled back to its highest point, it is at a height of 6.2 m. When it hits the wall, it is moving at 3.1 m/s. How high is the wrecking ball when it hits the wall? (Show your work and follow all of the steps of the GUESS method. Check your answer after you submit the form - it's in the feedback for this question.) |
Which of the following is a vector quantity?
speed
distance
acceleration
