(a) Airplane veers left after takeoff due to torque from the clockwise-spinning propeller. (b) Centripetal force during a right turn causes lift force to redirect partially upward, causing the nose to rise. Speed may affect nose drop.
(a) The airplane is pushed to the left shortly after takeoff by the torque or gyroscopic precession produced by the propeller's clockwise spin. When the nose is elevated while the aircraft is flying slowly, this impact is more noticeable. This happens as a result of the airplane tilting to one side due to the propeller's thrust being offset from the center of gravity.
(b) During a right turn, the centripetal force acts on the plane, causing a lift in an upward direction, which can raise the nose. However, a speed decrease can cause the nose to drop. Lift force is crucial in nose motion during turns
learn more about Centripetal force here:
https://brainly.com/question/14021112
#SPJ4
What happens when thermal energy is removed from a substance?(1 point) Responses All substances will freeze. All substances will freeze. The substance loses potential energy. The substance loses potential energy. The substance’s atoms lose kinetic energy. The substance’s atoms lose kinetic energy. The substance’s particles speed up
imagine that earth was upright with no tilt. how would this affect the seasons?
Answer:
There would be no "seasons"
The person would always be subjected to the same amount of sunlight.
Since the earth is tilted at about 23 deg, a person at that latitude would be subjected to sunlight from overhead to sunlight that appears 46 deg N of vertical.
A 4.50kg crate is suspended from the end of a short vertical rope of negligible mass. An upward force F(t) is applied to the end of the rope, and the height of the crate above its initial position is given by y(t) = (2.80m/s )t +(0.61m/s^3 )t^3 What is the magnitude of the force F when 3.60s ?
We know that Fg = mg = 4.5 kg * 9.8 m/s² = 44.1 NTherefore, F(t) = F_net + Fg = 1.5525 N + 44.1 N = 45.6525 NThe magnitude of the force F when t = 3.60 s is 45.65 N.Given,The mass of the crate, m = 4.5 kgHeight of the crate above its initial position, y(t) = (2.80m/s )t + (0.61m/s³)t³Let F(t) be the force applied upward on the rope.The upward force F(t) acting on the crate = Weight of the crate - Tension in the ropeTension in the rope is because of the force applied upward.
Therefore,Tension in the rope, T = F(t) - mgWhere g is the acceleration due to gravity= 9.8 m/s²Let's differentiate the given height of the crate equation to obtain the velocity of the crate above its initial position, dy(t)/dt.dy(t)/dt = (2.80m/s) + 3(0.61m/s³)t²We can determine the velocity of the crate at t= 3.60s by substituting the value of t = 3.60s. dy(3.60s)/dt = (2.80m/s) + 3(0.61m/s³)(3.60s)² = 16.34 m/sFrom the equation of motion, v² = u² + 2asWhere v is the final velocity, u is the initial velocity, a is the acceleration, and s is the distance.The initial velocity, u = 0m/s.The distance traveled by the crate when the force is applied, s = (2.80m/s)t + (0.61m/s³)t³ = (2.80m/s)(3.60s) + (0.61m/s³)(3.60s)³ = 23.63 mThe acceleration, a = (v² - u²)/2s = (16.34m/s²)/47.26m = 0.345 m/s²The net force, F_net = maWhere m is the mass of the crate and a is the acceleration of the crate due to the applied force F(t).F_net = m * a = 4.5kg * 0.345m/s² = 1.5525 NThe net force F_net is the sum of the force applied upward F(t) and the weight of the crate Fg, F_net = F(t) - FgWe know that Fg = mg = 4.5 kg * 9.8 m/s² = 44.1 NTherefore, F(t) = F_net + Fg = 1.5525 N + 44.1 N = 45.6525 NThe magnitude of the force F when t = 3.60 s is 45.65 N.
For more questions on Force
https://brainly.com/question/15251816
#SPJ11
11- An object of mass 0.2 kg moves in a circular path. If it makes 3/4 revolution in 0.3 s and its displacement is 6 m, calculate: a) The radius of the circular path ?
We can use the kinematic equations for circular motion to solve this problem. The equation we will use is:
θ = (s / r)
where θ is the angle of rotation (in radians), s is the displacement, and r is the radius of the circular path.
In this case, the object makes 3/4 revolution, which is equivalent to an angle of rotation of:
θ = (3/4) x 2π radians = 1.5π radians
The displacement is given as 6 m.
Therefore, we can rearrange the equation to solve for the radius:r = s / θ
r = 6 m / (1.5π radians)
r ≈ 1.273 m
Therefore, the radius of the circular path is approximately 1.273 meters.
What is a path ?
A path is a route or way that someone or something follows to reach a destination or achieve a particular goal. It can be physical or abstract, and can refer to a variety of contexts such as travel, communication, decision-making, or personal development.
A physical sense, a path can refer to a trail, road, or sidewalk that people use to walk, cycle, or drive to a particular location. In computing, a path refers to the sequence of directories and that lead to a specific file or folder.
To know more about path visit :
https://brainly.com/question/27325244
#SPJ1
how many types of classifications are there for a lunar eclipse?
There are three types of lunar eclipses: total, partial, and penumbral.
During a total lunar eclipse, the moon is completely shadowed by the Earth, resulting in a reddish-brown color. In a partial lunar eclipse, only a portion of the moon is shadowed, while in a penumbral lunar eclipse, the moon passes through the Earth's outer shadow, resulting in a subtle darkening of the moon's surface. These classifications are based on the degree to which the moon passes through the Earth's shadow during the eclipse.
To know more about lunar eclipse, here
brainly.com/question/29775053
#SPJ4
focusing a camera changes the distance between the lens and the film. does the eye focus by changing the distance between the lens and the retina? explain your answer.
Focusing a camera changes the distance between the lens and the film. And the eye focus by changing the distance between the lens and the retina is true as, the eye does focus by changing the distance between the lens and the retina.
What is the effect of changing the distance?When we focus on an object, the curvature of the lens in our eye changes. This causes the light rays from the object to converge and focus on the retina, located at the back of the eye.
In order to focus on objects at different distances, our eye's lens must adjust its shape by changing its curvature, which changes the distance between the lens and the retina. This process is called accommodation.
The process of focusing the eye is similar to the process of focusing a camera. In a camera, changing the distance between the lens and the film allows for the object to be in focus. Similarly, in the eye, changing the distance between the lens and the retina allows for objects to be in focus.
Therefore, the eye focuses by changing the distance between the lens and the retina.
Read more about the retina:
https://brainly.com/question/28098895
#SPJ11
The temperature of a gas stream is to be measured by a thermocouple whose junction can be approximated as a 1.2-mm-diameter sphere. The properties of the junction are k = 35 W/m °C, rho= 8500 kg/m3 ,and Cp = 320 J/kg °C, and the heat transfer coefficient between the junction and the gas is h = 65 W/m2 °C. Determine how long it will take for the thermocouple to read %95 of the initial temperature difference.
It will take about 12.12 minutes for the thermocouple to read 95% of the initial temperature difference of the sphere. This is due to difference in temperature.
What is the time required to read 95% of initial temperature difference?
In order to determine how long it will take for the thermocouple to read 95% of the initial temperature difference, the following formula is used:
t = (rho × V × Cp)/(h × pi × D) × ln ((Tinitial - T∞) / (Tinitial - Tcutoff))
where, t = time (s), ρ = density (kg/m³), V = volume (m³), Cp = specific heat capacity (J/kg °C), h = heat transfer coefficient (W/m²°C), D = diameter (m), Tinitial = initial temperature (°C), T∞ = surrounding temperature (°C), Tcutoff = temperature at which the thermocouple reading is 95% of the initial temperature difference (°C).
Substituting the given values into the above formula:
t = (8500 kg/m³ × (4/3 × pi × (0.0006 m)³)) / (65 W/m2 °C × pi × 0.0012 m) × ln ((100 °C - 25 °C) / (100 °C - 95 °C))
t = 727.31 s or 12.12 minutes.
Therefore, it will take approximately 12.12 minutes for the thermocouple to read 95% of the initial temperature difference.
Learn more about Thermocouple here:
https://brainly.com/question/14555057
#SPJ11
Describes depolarizing vs nondepolarizing neuromuscular blockers
Acetylcholine and non-depolarizing blockers battle it out for receptors in order to function. They assist with surgery and mechanical ventilation. Depolarizing substances.
On the other hand, result in prolonged activation and consequent desensitisation of the receptors.
Non-depolarizing neuromuscular blockers (nNMBs) are given as adjuvant therapy in the management of critically sick patients as well as as primary therapy to facilitate endotracheal intubations. nNMBs (rocuronium, vecuronium, pancuronium, atracurium, cisatracurium, mivacurium) are primarily used during routine and emergency intubations to facilitate airway management and lower the risk of laryngeal injury. This activity describes the indications, mode of action, administration techniques, significant adverse effects, contraindications, monitoring, and toxicity of nNMBs so that healthcare professionals can guide patient therapy towards the best results possible during anaesthesia and other medical procedures where nNMBs are beneficial therapeutically.
Learn more about Depolarizing here:
https://brainly.com/question/25533751
#SPJ4
How is a uniform beam rotational equilibrium but not translational equilibrium?
A uniform beam can be in rotational equilibrium but not translational equilibrium if there is a force acting on the beam that causes a torque but does not cause any net force in any particular direction
Explanation - A uniform beam is rotational equilibrium but not translational equilibrium because in rotational equilibrium, the net torque acting on the object is equal to zero while in translational equilibrium, the net force acting on the object is equal to zero. Here, the following are the given information: Uniform beam It is rotational equilibrium It is not translational equilibriumWhen a uniform beam is placed on two supports, it is in rotational equilibrium because the forces acting on it are balanced. This means that the net torque acting on the beam is equal to zero. However, the beam is not in translational equilibrium because the forces acting on it are not balanced. This means that the net force acting on the beam is not equal to zero.The formula for torque is τ= rF sin θwhere τ is torque, r is the distance from the pivot point to the point where the force is applied, F is the force applied, and θ is the angle between the force and the line of action of the force.In order for the beam to be in rotational equilibrium, the sum of the torques acting on it must be equal to zero. Therefore, the torques acting on one side of the beam must be equal and opposite to the torques acting on the other side of the beam.
For more such questions on Force
https://brainly.com/question/15251816
#SPJ11
when the air is in geostrophic balance, it flows _______ to isobars _________ the boundary layer.
When the air is in geostrophic balance, it flows parallel to isobars and above the boundary layer.
Geostrophic balance is a state of balance between the pressure gradient force and the Coriolis force, where the pressure gradient force is directed from higher to lower pressure, and the Coriolis force is perpendicular to the direction of motion. In this state, the wind flows parallel to the isobars, with the pressure gradient force and the Coriolis force balancing each other out.
The boundary layer is the layer of air near the Earth's surface where friction between the air and the surface slows down the wind and causes it to flow in a more complex manner, with the wind direction changing with height. However, in the geostrophic flow regime, the wind flow is typically above the boundary layer and thus not affected by surface friction.
Therefore, in geostrophic balance, the wind flows parallel to isobars and above the boundary layer, with little to no effect from the Earth's surface.
Learn more about geostrophic balance here
brainly.com/question/28314662
#SPJ4
what is the acceleration of an object flying upward during free fall?
During free fall, an object is subject to the force of gravity and its acceleration is equal to the acceleration due to gravity (g), which is approximately 9.81 meters per second squared (m/s²) near the surface of the Earth.
If an object is flying upward during free fall, its acceleration will still be equal to -9.81 m/s² (note the negative sign indicating that the acceleration is downward). This is because the direction of the acceleration due to gravity is always toward the center of the Earth.
Even if an object is moving upward, it is still subject to the gravitational force, which causes it to decelerate until it reaches its highest point and then starts to fall back down.
To learn more about acceleration refer to:
brainly.com/question/30762941
#SPJ4
electrical current of flow occurs when a person or conducting object bridges the gap between live conductors and the ground or live conductors. True or False
The statement "electrical current of flow occurs when a person or conducting object bridges the gap between live conductors and the ground or live conductors." is true because when the gap between conductors and the ground is covered then current flows.
This happens when electricity is conducted through a circuit and creates a potential difference between two points.
This potential difference can cause electrons to move through the circuit and creates a current flow. When there is a gap or break in the circuit, electrons will attempt to fill the gap, creating a current of flow.
This current can cause injury or shock to anyone bridging the gap, so it is important to take precautions when dealing with live wires.
To know more about potential difference click on below link:
https://brainly.com/question/12198573#
#SPJ11
pls help 60 pts
screenshot, fill out, then screenshot . attach document to answer using the paperclip button
Answer:
Here you go, hope this helps you pass :)
Explanation:
You're welcome.
what device is used through ureteroscope to capture an inact calculus or fragments if fractured by laser
The device used through a ureteroscope to capture an intact calculus or fragments if fractured by laser is called a basket retrieval device.
A ureteroscope is a specialized tool that is used to examine and treat the inside of the ureter and kidney. It is made up of a long, thin tube with a camera and a light source at the end, which is inserted into the patient's urinary tract through the urethra. The physician will be able to examine the lining of the bladder, ureters, and kidneys during this examination.
A basket retrieval device is a specialized tool that is used during ureteroscopy, which is a minimally invasive surgical technique used to examine the inside of the urinary tract. It is used to remove kidney stones or any fragments that have been broken down by laser lithotripsy.The basket retrieval device works by capturing the stones or fragments with its metal "basket" and then removing them from the body. The physician will then be able to extract the stones or fragments by retracting the basket into the ureteroscope's working channel. The stones will be disposed of or sent to a lab for further testing.
More on ureteroscope: https://brainly.com/question/28170411
#SPJ11
what is the current in a counductor if 3.15*10^18 electrons pass a given point in the conductor in 10 seconds
The current in a counductor if 3.15*10^18 electrons pass a given point in the conductor in 10 seconds is 0.0504 amperes
Current calculation.
The current in a conductor is defined as the rate at which electric charge flows through it. The unit of current is amperes (A), which is defined as coulombs per second. One coulomb is equal to the charge on 6.24 × 10^18 electrons.
Given that 3.15 × 10^18 electrons pass a given point in the conductor in 10 seconds, we can find the charge that flows through the point as follows:
Number of electrons = 3.15 × 10^18
Charge on one electron = 1.6 × 10^-19 coulombs
Total charge = Number of electrons × Charge on one electron
Total charge = 3.15 × 10^18 × 1.6 × 10^-19
Total charge = 0.504 coulombs
The current is the rate of flow of charge, so we can find it by dividing the total charge by the time taken:
Current = Total charge ÷ Time taken
Current = 0.504 coulombs ÷ 10 seconds
Current = 0.0504 amperes (A)
Therefore, the current in the conductor is 0.0504 amperes, or 50.4 milliamperes (mA).
Learn more about current below.
https://brainly.com/question/24858512
#SPJ1
an electromagnetic wave is transporting energy in the positive y direction. at one point and one instant the magnetic field is in the positive x direction. the electric field at that point and instant points in the
Energy is being transported in the positive y direction by an electromagnetic wave. The magnetic field is in the positive x direction at one spot and one moment. At that precise moment, the electric field is oriented in the "negative z" direction.
The given electromagnetic wave is transporting energy in the positive y direction. At one point and one instant, the magnetic field is in the positive x direction. Now we have to find the direction of the electric field at that point and instant. According to the right-hand rule, when the magnetic field is directed towards the positive x-axis, the electric field will be directed downwards along the negative z-axis. Therefore, the electric field at that point and instant points in the negative z direction.
To know more about electromagnetic wave:https://brainly.com/question/75996
#SPJ11
A fisherman is holding a fishing rod with a large fish hanging from thee line. Identify the forces acting on the rod and describe the interaction partner of each.
In summary, when a fisherman is holding a fishing rod with a large fish hanging from the line, there are multiple forces acting on the rod. The external forces are the weight of the fish and the force of air resistance, while the internal forces are the tension in the fishing line and the force that the fisherman is exerting on the rod. The interaction partners of these forces are the fishing line, the rod, the fish, and the fisherman's hand.
When a fisherman is holding a fishing rod with a large fish hanging from the line, the following forces act on the rod:
- Tension force: This is the force that is pulling on the line that is attached to the fish. The line is creating a tension force in the rod as it tries to pull the rod downwards.
- Weight force: This is the force that is acting on the rod and the fish due to gravity. The weight force is directed downwards towards the earth.
- Normal force: This is the force that is exerted by the fisherman on the rod. The normal force acts perpendicular to the surface of the rod and prevents the rod from falling down.
The interaction partner of each force acting on the rod is as follows:
- Tension force: The interaction partner of the tension force is the fish. The line is pulling on the fish and the fish is exerting a force back on the line that is equal in magnitude and opposite in direction. This is the principle of Newton's third law of motion.
- Weight force: The interaction partner of the weight force is the earth. The earth is exerting a force back on the rod and the fish that is equal in magnitude and opposite in direction. This is also the principle of Newton's third law of motion.
- Normal force: The interaction partner of the normal force is the fisherman. The fisherman is holding the rod and is exerting a force on the rod that is perpendicular to its surface. This force prevents the rod from falling down and is equal in magnitude and opposite in direction to the weight force acting on the rod.
In summary, the forces acting on the rod when a fisherman is holding a fishing rod with a large fish hanging from the line are tension force, weight force, and normal force. The interaction partners of these forces are the fish, the earth, and the fisherman, respectively.
For more such questions on external forces
https://brainly.in/question/23859011
#SPJ11
for each charge, determine the direction of the magnetic force. for the last one, determine the direction of the magnetic field. the sign of the charge is given for each part.
For each charge, the direction of the magnetic force can be determined using the right-hand rule. For the last one, the direction of the magnetic field can be determined by observing the direction of the current.
The right-hand formula can be used to calculate the direction of the magnetic field for each charge. According to the formula, if you aim your right thumb in the direction of the charged particle's velocity and your fingers in the direction of the magnetic field, the way your hand confronts is the magnetic force direction.
To identify the direction of the magnetic field for the final charge, examine the direction of the current. The magnetic field is perpendicular to the current and can also be calculated with the right-hand formula.
Learn more about right-hand rule:
https://brainly.com/question/27332584
#SPJ4
what are two characteristics of net forces that are balanced
Balanced net forces have equal and opposing forces that cancel each other out and provide a net force of zero, which does not alter the motion of an item.
An object's velocity remains constant and motion is unaltered when the net forces acting on it are balanced. This indicates that the thing is either stationary or moving continuously. When the forces exerted on an item are opposing in direction and of equal magnitude, they are said to be balanced forces. The forces in this situation cancel one another out, leaving a net force of zero. This can happen when one force is applied to an item and that object applies an equal and opposite force in the opposite direction to another object. It can also happen when two or more forces are applied in opposing directions and of equal magnitude. Understanding equilibrium and stability in physics requires a knowledge of the idea of balanced forces.
learn more about Balanced net forces here:
https://brainly.com/question/29769471
#SPJ4
suppose that one particle of the flow approaches a plate of a capacitor. explain what happens to the other plate of the capacitor?
The other plate of the capacitor is induced with an opposite charge through electrostatic induction as the particle of the flow approaches one plate.
As the particle of the flow approaches one plate of the capacitor, it induces an opposite charge on the other plate of the capacitor through the process of electrostatic induction. The electric field produced by the charge on the approaching plate pushes the electrons on the other plate away from the approaching plate, resulting in an accumulation of charge of the opposite sign on the other plate.
This process continues until the potential difference between the plates becomes large enough to produce a discharge, after which the process of electrostatic induction ceases. The discharge may occur in the form of a spark or a breakdown of the dielectric material separating the plates, depending on the strength of the electric field and the dielectric strength of the material.
Overall, the other plate of the capacitor experiences a temporary polarization and a buildup of charge of the opposite sign due to the approaching particle.
To know more about capacitor, refer here:
https://brainly.com/question/30889004#
#SPJ11
The moment of inertia of a solid cylinder about its axis is given by 1/2MR 2 . If this cylinder rolls without slipping, the ratio of its rotational kinetic energy to its translational kinetic energy is:A. 1:1
B. 2:2
C. 1:2
D. 1:3
Answer:
I = 1/2 M R^2 moment of inertia
Translational energy due to rotation
Er = 1/2 I ω^2 = 1/2 M R^2 ω^2 = 1/2 M V^2 since V = R ω
Thus (A) the translational KE is equal to the rotational energy and
Ek = Er + Et for the total energy of the cylinder
the concentration of which component of the atmosphere varies the most?
The concentration of water vapor varies the most in the atmosphere.
The atmosphere is a thin layer of gas that surrounds the Earth. The atmosphere is composed of roughly 78% nitrogen and 21% oxygen, with trace amounts of other gases like argon and carbon dioxide. In addition, water vapor and aerosols are also present in the atmosphere.
Water vapor is the atmospheric component that fluctuates the most in concentration. It has a critical role in the planet's climate and is present in varying amounts in all parts of the atmosphere. Water vapor concentration is essential in the Earth's energy balance since it is a greenhouse gas that captures radiation from the sun and heats the planet's surface.
The amount of water vapor in the atmosphere can vary greatly depending on the temperature, location, and other environmental factors. Warm air can hold more water vapor than cold air, and areas with higher humidity can have more water vapor than arid regions. Overall, the concentration of water vapor in the atmosphere is constantly changing and fluctuating.
To learn more about water vapor, visit: https://brainly.com/question/1361830
#SPJ11
what is the potential difference across a capacitor after it has been discharging for a very long time?
The potential difference across a capacitor after it has been discharging for a very long time is 0 volts. This is because the capacitor is empty of charge, and thus has no potential difference between its two terminals.
A capacitor is a type of electrical component that stores energy in an electric field. The energy is stored in the form of electric charges on two conductive plates.
The plates are separated by an insulating material called a dielectric. The potential difference across a capacitor is proportional to the amount of charge stored on the plates.
What happens when a capacitor discharges?When a capacitor discharges, it loses the stored charge. This discharge occurs when the capacitor is connected to a circuit. The capacitor will then begin to discharge as the charges on the plates flow through the circuit.
The potential difference across the capacitor will decrease as the charges on the plates decrease.
The capacitor has been completely discharged and no longer has any potential difference.
Thus, the potential difference across a capacitor after it has been discharging for a very long time is zero.
Learn more about the potential difference here:
brainly.com/question/24142403
#SPJ11
2.1 [2] As more resistors are added in series, the equivalent resistance of the circuit approaches infinity. In contrast, as more resistors are added in parallel, the equivalent resistance a. approaches infinity b. approaches zero c. becomes zero d. approaches 1 Ω
2.2 [2] Kirchhoff's loop rule is equivalent to which of the following principles? a. conservation of charge b. conservation of energy c. conservation of mass d. conservation of force
2.1 As more resistors are added in parallel, the equivalent resistance approaches zero
2.2 Kirchhoff's loop rule is equivalent to the conservation of energy principle.
As more resistors are added in series, the equivalent resistance of the circuit approaches infinity. In contrast, as more resistors are added in parallel, the equivalent resistance approaches zero. This statement is TRUE. The equivalent resistance, Req, of a parallel combination of resistors is less than any of the resistors in the combination, while for a series combination it is equal to the sum of the resistances.
Kirchhoff's loop rule is equivalent to the conservation of energy principle. Kirchhoff's loop rule or Kirchhoff's voltage law (KVL) is a result of the conservation of energy principle. The principle of conservation of energy states that energy can neither be created nor destroyed, it can only be transformed from one form to another. In a closed loop, the total energy gained is equal to the total energy lost, according to the principle of conservation of energy.
Learn more about Kirchhoff's loop rule and equivalent resistance at : https://brainly.com/question/30580929
#SPJ11
greenhouse gases in the atmosphere selectively absorb radiation at what wavelength?
Answer:
They absorb radiation in the ultraviolet area - somewhat less than 4000 Angstroms or 400 mμ.
The reduction of the ozone layer in the upper atmosphere causes more of the shorter wavelengths to reach the surface of the earth and then to be reradiated at longer wavelengths causing global warming.
A survey was conducted at local colleges around Madison, Wisconsin to find out the average height of a college student. Of 692 students surveyed, 421 replied that they were over 6 feet tall. What is the standard error? Answer choices are rounded to the hundredths place.
A survey was conducted at local colleges around Madison where 692 students were surveyed, and 421 replied that they were over 6 feet tall showing a standard error of 0.0084 in the average height of a college student.
The standard error is given by the formula given below:
[tex]$$SE= {s}/{\sqrt{n}}$$[/tex]
Where s is the standard deviation,
n is the sample size.
Now let us find out the standard deviation by using the formula given below:
[tex]$$s=\sqrt{\frac{(421-271.17)^2+(271.17-270)^2}{692-1}}$$[/tex]
After calculating we get that the standard deviation s is equal to $0.2208$.
Now let us plug the value of the standard deviation s and sample size n into the formula for standard error:
[tex]$$SE={s}/{\sqrt{n}}$$[/tex]
On substituting the respective values, we get [tex]$$SE={0.2208}/{\sqrt{692}}$$[/tex]
On solving, we get that the standard error is equal to 0.0084
Therefore, the standard error is 0.0084.
Learn more about standard error: https://brainly.com/question/14467769
#SPJ11
Why is this wrong? Can anybody please help me thanks!
A resultant force of 5437 N would accelerate an 810 kg mass at 6.7 m/s². The answer that you have entered is 5427 and that is why it says incorrect.
What is a resultant force?A resultant force is the single force that represents the combined effect of two or more forces acting on an object. It is the net force that results from the vector sum of all the individual forces. The direction and magnitude of the resultant force determine the motion of the object, whether it is at rest, moving at a constant velocity, or accelerating.
To calculate the resultant force, we can use the formula:
Resultant force = mass x acceleration
Plugging in the given values, we get:
Resultant force = 810 kg x 6.7 m/s²
Resultant force = 5437 N
Therefore, a resultant force of 5437 N would accelerate an 810 kg mass at 6.7 m/s².
To find out more about resultant forces, visit:
https://brainly.com/question/16380983
#SPJ1
A car speeds up at a constant rate pf 4 m/s?. An identical car takes a right turn with 4 m radius at constant speed of 8 m/s. Which of the following statements is correct? A. The car speeding up experiences the greater net force. B. The car speeding up experiences zero net force. C. The car that is turning experiences the greater net force. D. The car that is turning experiences no net force.
The correct answer is the car that is turning experiences no net force.
What is a net force?A net force is the sum of all forces acting on an object, taking into account their magnitude and direction. If an object is not in equilibrium, it experiences a net force, which causes it to accelerate. In physics, a net force, often known as unbalanced force, is defined as the total sum of all forces that act on an object. If the forces acting on an object are balanced, meaning they are the same size but opposite in direction, the object will maintain a constant speed with no acceleration.
In this scenario, the car speeding up experiences the greater acceleration. The car that is turning, on the other hand, experiences no net force since the force acting on the car, the centripetal force, is equal to the force required to maintain its motion.
Therefore, the answer is option D. The car that is turning experiences no net force.
Learn more about net force here:
https://brainly.com/question/14361879
#SPJ11
ercury's perihelion slowly precesses around the sun by a bit less than 2 degrees per century. this precession can be fully accounted for by newton's theory of gravity, although general relativity also gives the same answer. group of answer choices true false
The statement is true. Mercury's precession can be fully accounted for by both Newton's theory of gravity and general relativity.
Newton's law of universal gravitation states that any two bodies in the universe are attracted to each other with a force that is directly proportional to the product of their masses and inversely proportional to the square of the distance between them. This force can explain why the perihelion of Mercury is slowly precessing around the sun. According to Einstein's general theory of relativity, gravity is caused by the curvature of space-time around a massive body, such as the sun. This curvature of space-time causes Mercury to precess around the sun.
Newton's theory of gravity and general relativity provide equivalent explanations for the precession of Mercury's perihelion, which is a phenomenon in celestial mechanics. The precession of Mercury's perihelion is the slow rotation of the planet's elliptical orbit around the Sun's perihelion (the point of closest approach).It is well-known that Mercury's perihelion rotates by 42.98 arcseconds per century, or 1.39 degrees per century. This is caused by the gravitational influence of other planets, such as Venus and Jupiter, which produce small changes in Mercury's orbit. However, when this is taken into account, a tiny residual effect remains that cannot be accounted for using Newton's theory of gravity. This additional precession, known as the anomalous precession, can only be explained by general relativity.
The statement "Mercury's perihelion slowly precesses around the sun by a bit less than 2 degrees per century. This precession can be fully accounted for by Newton's theory of gravity, although general relativity also gives the same answer." is true.
To know more about Newton's theory of gravity please visit :
https://brainly.com/question/11490572
#SPJ11
if the true stress - true plastic strain curve can be described by the hollomon equation , obtain the true strain at the onset of necking in terms of hollomon equation parameters
The true strain at the onset of necking can be obtained from the Hollomon equation as follows: true strain = (K/S)^(1/n).
Here, K is the strength coefficient, S is the stress, and n is the strain hardening exponent. Thus, given the values of these parameters, we can calculate the true strain at the onset of necking.
The Hollomon equation is a mathematical expression for the true stress-true strain curve that relates the true stress to the true strain in a material. It is expressed as follows: true stress = K(true strain)^n. Here, K is the strength coefficient and n is the strain hardening exponent.
The true strain at the onset of necking is the strain at which the material starts to deform plastically instead of elastically. This can be obtained from the Hollomon equation by rearranging it to the form true strain = (K/S)^(1/n). Thus, given the values of the parameters K, S, and n, we can calculate the true strain at the onset of necking.
To know more about elastically click on below link:
https://brainly.com/question/14450755#
#SPJ11
