if the variable capacitor in an fm receiver ranges from 10.9 pf to 16.4 pf , what inductor should be used to make an lc circuit whose resonant frequency spans the fm band?

Answers

Answer 1

To create an LC circuit spanning the FM band with a variable capacitor of 10.9-16.4 pF, use the formula L = 1/(4π²f²C).

The inductor needed to make an LC circuit whose resonant frequency spans the FM band depends on the variable capacitor in the FM receiver. In your case, the variable capacitor ranges from 10.9 pF to 16.4 pF. To determine the inductor needed for the LC circuit, you can use the following formula:

L = (1/ (4π² * f² * C))

Where:

"L" is the inductor. "f" is the frequency of the LC circuit. "C" is the capacitor.

For example, if you set the variable capacitor to 10.9 pF, the inductor needed to make an LC circuit whose resonant frequency spans the FM band would be:

L = (1/ (4π² * f² * 10.9 pF))

Learn more about circuit: https://brainly.com/question/29255502

#SPJ11


Related Questions

what is the minimum angular velocity (in rpm ) for swinging a bucket of water in a vertical circle without spilling any? the distance from the handle to the bottom of the bucket is 35 cm . express your answer in revolutions per minute.

Answers

The minimum angular velocity (in rpm) for swinging a bucket of water in a vertical circle without spilling any is 5.56 rpm.

The minimum angular velocity (in rpm) for swinging a bucket of water in a vertical circle without spilling any is given by the formula; Vmin=√g/R

where:

Vmin = minimum angular velocity (in rpm)g = acceleration due to gravity (9.81 m/s²)R = radius of the circular path or distance from the handle to the bottom of the bucket (35 cm)

To express the answer in revolutions per minute, the radius of the circle must be converted to meters;R = 35 cm = 0.35 m

Substituting the values given above into the formula;

Vmin=√g/R Vmin=√9.81/0.35 Vmin = 5.56 rpm

Therefore, the minimum angular velocity (in rpm) for swinging a bucket of water in a vertical circle without spilling any is 5.56 rpm.

Learn more about velocity: https://brainly.com/question/25749514

#SPJ11

write an expression for the magnitude of the force, f, exerted on the firefighter by the pole. answer in terms of the variables from the problem statement as well as g for the acceleration due to gravity.

Answers

The expression for the magnitude of the force exerted on the firefighter by the pole can be expressed as  F = mg + ma.  

Where m is the mass of the firefighter,

g is the acceleration due to gravity, and

a is the acceleration of the pole

In order to find an expression for the magnitude of the force, F, exerted on the firefighter by the pole, we need to consider the forces acting on the firefighter.

According to Newton's second law of motion, the force acting on an object is equal to its mass multiplied by its acceleration. In this case, the forces acting on the firefighter are the gravitational force, which is pulling the firefighter downwards with a force of mg, and the force exerted on the firefighter by the pole, which is pushing the firefighter upwards with a force of ma. Therefore, the total force acting on the firefighter is given by the sum of these two forces, which is: F = mg + ma

Thus, this expression gives us the magnitude of the force exerted on the firefighter by the pole. Here, m is the mass of the firefighter, g is the acceleration due to gravity, and a is the acceleration of the pole. if the pole is not accelerating (i.e., if a = 0), then the expression reduces to F = mg, which is the gravitational force acting on the firefighter.

To know more about Magnitude please visit :

https://brainly.com/question/30337362

#SPJ11

charge q1 is distance s from the negative plate of a parallel-plate capacitor. charge is distance 2s from the negative plate. what is the ratio of their potential energies?

Answers

The electric potential energy, U, of two point charges is given by the equation, U = kq1q2/r where k is Coulomb's constant, q1 and q2 are the charges and r is the distance between the two charges. Now, let's solve the question using this equation. There are two charges, q1 and q2, and a parallel plate capacitor between them. The distance of q1 from the negative plate is s, and the distance of q2 from the negative plate is 2s. The charges have the same magnitude of charge, so let's assume q1 = q2 = q. Using the formula mentioned earlier, we get U1= kq^2/sU2= kq^2/2s. Therefore, the ratio of their potential energies is U2/U1= kq^2/2s / kq^2/sU2/U1= (kq^2/2s) × (s/kq^2)U2/U1= 1/2.

Therefore, the ratio of their potential energies is 1:2.

For more information regarding this topic, you can click the below link

https://brainly.com/question/14306881

#SPJ11

The half life of a radioactive substance is 5 hours. If 5g of the substance is left after 20 hours, determine the original mass of the substance​

Answers

Answer:

The original mass of the substance was 10g.

Explanation:

The half-life of a radioactive substance is the amount of time it takes for half of the substance to decay. In this case, the half-life is 5 hours.

We can use the half-life formula to find the original mass of the substance:

N = N0 * (1/2)^(t/T)

where:

---N0 is the initial mass of the substance

---N is the remaining mass of the substance after time t

---T is the half-life of the substance

We know that after 20 hours, only half of the substance remains:

N = N0 * (1/2)^(20/5) = 0.5 * N0

If we solve for N0, we get:

N0 = N / 0.5 = 5g / 0.5 = 10g

Therefore, the original mass of the substance was 10g.

a student pulls a 1500 kg suitcase along a flat sidewalk. if the cord on the suitcase breaks when the force is greater than 50n, what is the maximum acceleration that the student can achieve with the suitcase?

Answers

The maximum acceleration that the student can achieve with the 1500 kg suitcase is 50N/1500kg = 0.033 m/s2.

Acceleration is the change in velocity per unit time. Acceleration is a vector quantity that has both magnitude and direction. Acceleration is divided into deceleration acceleration and acceleration acceleration. Acceleration decreases meaning the direction of acceleration is opposite to the direction of velocity.


To calculate the maximum acceleration, we can use the following equation:
Force = Mass x Acceleration. Therefore, 50N = 1500kg x Acceleration

Solving for Acceleration, we get 50N/1500kg = 0.033 m/s2.

Learn more about acceleration : brainly.com/question/20595261

#SPJ11

when one stationary object is replaced by another stationary object, the change between the two objects maybe perceived as the movement of a single object. this creates?

Answers

When one stationary object is replaced by another stationary object, the change between the two objects maybe perceived as the movement of a single object. This creates an optical illusion.

An optical illusion is defined as a visual phenomenon in which the information gathered by the eye is processed in a way that results in a false perception of reality or the visual impression of seeing something that is not present or incorrectly perceiving it. It is a misinterpretation of a visual stimulus caused by the brain's ability to misjudge sensory information.

It can happen when visual information is processed in the brain, and it can create an impression of movement that isn't there. This phenomenon occurs when an object is moving or when the eyes are moving around, but it can also happen when the object being looked at is stationary.

When one stationary object is replaced by another stationary object, the change between the two objects maybe perceived as the movement of a single object. This creates an optical illusion because the visual system is misled into thinking that the object is moving.

The brain continues to process visual information even when the object is stationary, creating the impression that the object is moving. This is why an optical illusion can be used to make a stationary object appear to move or to make a moving object appear to be stationary.

Learn more about optical illusion: https://brainly.com/question/3260067

#SPJ11

suppose your planet at 1 meter from the basketball represents a distance of 4 x 107 km (-0.3 al) from the star. the next closest star to the sun is 4 x 1013 km away. how far away from the model star/planet would you have to be for the distances in the system to be to scale? express your answer in meters and kilometers.

Answers

Answer: The model star/planet would have to be 1,000 km away from the next closest star.

Explanation:
We need to find out the distance required for the distances in the system to be in scale.

Let's use the proportion to solve the problem:

1 m/4 × 10⁷ km = x/4 × 10¹³ km

Where x is the distance required for the distances in the system to be in scale.

Cross-multiply: 4 × 10¹³ km × 1 m = 4 × 10⁷ km × x

Simplify: 4 × 10¹³ m = 4 × 10⁷ x

Divide both sides by 4 × 10⁷ :1 × 10⁶ = x

Therefore, the distance required for the distances in the system to be in scale is 1 × 10⁶ m or 1,000 km.

So the model star/planet would have to be 1,000 km away from the next closest star.

Learn more about distance here

https://brainly.com/question/26550516

#SPJ11

A typical neutron star has a mass of about 1.5Msun and a radius of 10 kilometers Calculate the average density of a neutron star. Express your answer in kilograms per cubic centimeter to two significant figures.

Answers

The average density of the neutron star that has a mass of about 1.5Msun and a radius of 10 kilometers rounded off to two significant figures is 5.9 × 10¹⁴ kg/cm³

The average density of a neutron star can be calculated using the following formula;`d = (3M)/(4πr³)`where `d` is the average density of the neutron star, `M` is the mass of the neutron star, and `r` is the radius of the neutron star.Using the given values in the formula, we get;`d = (3 × 1.5 × 1.989 × 10³⁰)/(4π × (10 × 10³)³)` = 5.9 × 10¹⁷ kg/m³To convert kg/m³ to kg/cm³, we can use the following conversion factor;1 m³ = 10⁶ cm³Therefore,1 kg/m³ = 10⁻³ kg/cm³So, the average density of the neutron star in kg/cm³ is;`d = (5.9 × 10¹⁷) × (10⁻³)` = 5.9 × 10¹⁴ kg/cm³Therefore, the average density of the neutron star is 5.9 × 10¹⁴ kg/cm³ (rounded to two significant figures).Answer: 5.9 × 10¹⁴ kg/cm³.

More on density: https://brainly.com/question/15700804

#SPJ11

Which of the following correctly compares the Sun's energy generation process to the energy generation process in human-built nuclear power plants?
Both processes involve nuclear fusion, but the Sun fuses hydrogen while nuclear power plants fuse uranium.
The Sun generates energy by fusing small nuclei into larger ones, while our power plants generate energy by the fission (splitting) of large nuclei.
The Sun generates energy through nuclear reactions while nuclear power plants generate energy through chemical reactions.
The Sun generates energy through fission while nuclear power plants generate energy through fusion.

Answers

The correct comparison of the energy generation processes is "The Sun generates energy by fusing small nuclei into larger ones, while our power plants generate energy by the fission (splitting) of large nuclei". Thus, the correct options are A and B.

What is Nuclear power?

Nuclear reactions involve the alteration of an atom's nucleus in both cases. Nuclear power plants and the sun both use energy generated by these nuclear reactions to produce electricity. The difference is in the type of nuclear reaction that takes place.

In the Sun, nuclear fusion is the process by which atomic nuclei of low atomic number fuse to form a heavier nucleus with the release of energy. The energy produced in this way is what makes the Sun so hot and bright. In a nuclear power plant, nuclear fission is the process by which the nucleus of an atom is split into two smaller nuclei.

The energy that is released in the process is used to heat water, creating steam that drives a turbine, which in turn drives a generator to produce electricity.

Therefore, the correct options are A and B.

Learn more about Nuclear power here:

https://brainly.com/question/18769119

#SPJ11

At a given pressure, a substance in the saturated vapor phase will be at a ______ temperature than a superheated vapor.

Answers

At a given pressure, a substance in the saturated vapor phase will be at a lower temperature than a superheated vapor.

What is a saturated vapor phase?

Saturated vapor refers to the state of a material in which it contains a maximum quantity of vapor that is uniformly blended with the liquid or solid state of the same chemical composition at a specified temperature and pressure.

What is a superheated vapor?

A superheated vapor is a vapor that is heated beyond its boiling point or saturation temperature for its pressure. As a result, it will not condense back into a liquid phase until it has cooled sufficiently. As a result, it's simply vapor, with no liquid portion to it.

What happens when pressure remains constant and the temperature of a substance rises?

According to Charles's law, if the pressure of a gas is kept constant, the volume of the gas varies directly with the temperature. If pressure remains constant and temperature increases, the volume of a substance expands, indicating that molecules are gaining energy and colliding with one another more frequently. As a result, the kinetic energy of the system increases. When a substance is in a superheated vapor state, it is at a higher temperature than when it is in a saturated vapor state at the same pressure.

Learn more about saturated vapor phase here: https://brainly.com/question/13407628

#SPJ11

a rock is thrown upward with a velocity of 12 meters per second from the top of a 42 meter high cliff, and it misses the cliff on the way back down. when will the rock be 12 meters from ground level?

Answers

The rock will be 12 meters from the ground level after it has been thrown upward with a velocity of 12 meters per second from the top of the 42 meter high cliff for a total of 3.5 seconds.

What is the cliff?

The cliff is the height that generally has the highest height and it can be mountains, stones, buildings.

This is because the total time taken for the rock to fall back down will be the same as the total time taken for the rock to reach the top of the cliff. The equation used to calculate this is: time = distance / velocity. Therefore:

Time = 42 meters (cliff height) / 12 meters per second (velocity) = 3.5 seconds.

So, the rock will be 12 meters from the ground level after 3.5 seconds.

Read more about cliff here:

https://brainly.com/question/22789028

#SPJ11

How does a nuclear power plant produce electricity?

Responses

Quickly moving neutrons coming out of the reaction create a gas which turns a turbine that produces electricity.
Quickly moving neutrons coming out of the reaction create a gas which turns a turbine that produces electricity.

Quickly moving neutrons coming out of the reaction are slowed down by water. The water heats up and turns into steam. The steam turns the turbine and produces electricity.
Quickly moving neutrons coming out of the reaction are slowed down by water. The water heats up and turns into steam. The steam turns the turbine and produces electricity.

Quickly moving neutrons coming out of nuclear reactions are used to turn turbines that produce electricity.
Quickly moving neutrons coming out of nuclear reactions are used to turn turbines that produce electricity.

Quickly moving neutrons give their kinetic energy to the surrounding water. The water's energy is then used to turn turbines and produce electricity.

Answers

Water slows down neutrons that are leaving nuclear processes quickly. As the water warms up, steam is produced. Electricity is generated by the turbine that the steam turns.

Nuclear power plantA facility that uses nuclear reactions to produce electricity is known as a nuclear power plant. Nuclear fission—the splitting of an atom's nucleus—is used in these reactions to release a significant quantity of energy.Nuclear fission is started at a nuclear power plant's reactor core by blasting the fuel, which is typically uranium-235 or plutonium-239, with neutrons. The heat produced by the fuel's fission is utilized to boil water into steam. To generate electricity, the steam powers a turbine, which in turn powers a generator.The reactor core is encased in a substantial, protective vessel known as the reactor vessel in order to prevent the uncontrolled emission of radioactive particles.

learn more about electricity here

https://brainly.com/question/776932

#SPJ1

A battery-powered toy car pushes a stuffed rabbit across the floor.Part ADraw a free-body diagram for a car (assume that it is moving from left to the right).Draw the force vectors with their tails at the dot. The orientation of your vectors will be graded. The exact length of your vectors will not be graded but the relative length of one to the other will be graded.Part BDraw a free-body diagram for a rabbit.Draw the force vectors with their tails at the dot. The orientation of your vectors will be graded. The exact length of your vectors will not be graded but the relative length of one to the other will be graded.

Answers

Part A: Thrust acts on the right in the direction of motion. Gravity acts downward.

Part B:  The direction of air resistance is opposite to the direction of motion, which is shown towards the left. Gravity acts downwards.

Part A:

A free-body diagram for a car is as follows:

The direction of friction is opposite to the direction of motion, which is shown towards the left.
The diagram shows three forces acting on the toy car that is battery-powered, which is as follows:
The force due to friction is labeled as [tex]f_K[/tex].

The force of thrust is labeled as [tex]f_T[/tex]. The force of gravity is labeled as [tex]f_g[/tex].
Part B:

A free-body diagram for a rabbit is as follows:
The diagram shows three forces acting on the stuffed rabbit that is being pushed by a toy car that is battery-powered, which is as follows:

The direction of friction is opposite to the direction of motion, which is shown towards the right.
The force due to friction is labeled as [tex]f_K[/tex]. The force due to air resistance is labeled as fair. The force of gravity is labeled as [tex]f_g[/tex].
For similar question on Gravity

https://brainly.com/question/557206

#SPJ11

Select the correct location on the image.
The image shows the visible light spectrum received from a star. Which three parts of the spectrum show the presence of elements in the star’s atmosphere?

Answers

The visible light spectrum is the range of wavelengths the human eye can detect, ranging from 380 to 700 nanometers.

What are visible light examples?

People think of the sun, light bulbs, candles, and flames when they think of light, but visible light originates from many sources and in many hues. Other visible light sources include television and computer displays, glow sticks, and pyrotechnics.

This is why this area of the electromagnetic spectrum is known as the visible spectrum or colour spectrum. It primarily comprises of seven colours: violet, blue, green, yellow, orange, and red.

Learn more about visible light spectrum

brainly.com/question/18704022

#SPJ1

Answer:

It is the three spots where there are lines. Between 400 and 500(the two lines), between 600 and 700(the two lines), and the one line between 700 and 800.

hydroelectric, wind, geothermal, and parabolic solar collection all rely on spinning turbines (connected to a generator) to produce electricity. explain how each provides the force to do so.

Answers

Hydroelectric energy is generated by capturing the energy of flowing water. As water flows through a turbine, the blades of the turbine spin and generate electricity.

How does the different energies provide force?

Wind energy is generated by capturing the kinetic energy of the wind. As wind passes through the turbine, the blades spin and generate electricity.

Geothermal energy is generated by harnessing the natural heat of the Earth’s core. Heat from the Earth’s core is used to generate steam, which is then used to spin a turbine and generate electricity.

Parabolic solar collection is a method of collecting the sun’s energy using large reflective mirrors. The mirrors focus the sunlight onto a central point, which is then used to spin a turbine and generate electricity.

Thus, all of these power sources rely on spinning turbines connected to a generator to produce electricity.

Read more about Electricity here:

https://brainly.com/question/158098

#SPJ11

why can't we fall safely with the help of parachute towards the moon?​

Answers

Answer:

The Moon has no atmosphere so there is no drag on the capsule to slow its descent; parachutes will not work. Lunar landing vehicles were equipped with rocket engines that were fired by the pilot to provide lift — thrust in the opposite direction of descent — during the rapid descent to the Moon's surface.

The moon does not harbor any appreciable atmosphere. Therefore no parachute, no matter how large, will operate properly on the moon. Air is required in order to inflate the parachute and slow down the descending object. Remember geologist Harrison Schmidt, the ONLY scientist to visit the moon? He was one of the last two people to ever touch the lunar surface. (Apollo 17). He demonstrated what would happen when two objects of different masses were dropped simultaneously from about five feet above the moon’s surface. He dropped a hammer and a feather. They fell at the same rate and hit the surface at exactly the same instant! There was no atmosphere to cause the feather to flutter. Note: Careful observers may notice that in videos of the the descending Apollo Lunar Lander (“The Eagle has landed”) lunar dust is kicked up by the craft’s engines. The dust moves out in straight lines, not in billowing clouds! PROOF that the film was made in the airless void of the moon and NOT in some clandestine film studio on Earth. No moon landing hoax!

what happens after the helium flash in the core of a star?

Answers

After the helium flash in a star, the core quickly heats up and expands.

A helium flash is the very brief thermal runaway nuclear fusion of significant amounts of helium into carbon during the red giant phase of low mass stars (between 0.8 solar masses (M) and 2.0 M). The centre expands as a result of the core becoming warmer as a result of this.

Following the onset of helium nuclear reactions in a star's core, helium nuclei fuse to create carbon and oxygen.

Most of the time, the stars' positions in reference to one another remain constant. Convergence between Orion and Taurus is ongoing. Ursa Minor is never far from Draco. The stars appear to us as an endless backdrop painting in the sky that hardly moves in reference to one another.

To know more about stars:

https://brainly.com/question/29572549

#SPJ4

4. Once the child in the sample problem reaches the bottom of the hill,
she continues sliding along flat; snow-covered ground until she comes
to a stop. If her acceleration during this time is -0.392 m/s², how long
does it take her to travel from the bottom of the hill to her stopping
point?

Answers

Answer:

8.04 seconds

Explanation:

Assuming that the child starts from rest at the bottom of the hill and travels until she comes to a stop, we can use the following kinematic equation:

v_f^2 = v_i^2 + 2ad

where v_f is the final velocity (which is zero since the child comes to a stop), v_i is the initial velocity (which is the velocity at the bottom of the hill), a is the acceleration (-0.392 m/s²), and d is the distance traveled.

We can solve for d:

d = (v_f^2 - v_i^2) / (2a)

= (0 - v_i^2) / (2-0.392)

= v_i^2 / 0.784

Since the child is sliding along flat snow-covered ground, there is no change in elevation, so we can use the distance traveled from the bottom of the hill to the stopping point as the distance d.

To find the time it takes for the child to travel this distance, we can use the following kinematic equation:

d = v_it + 0.5a*t^2

where t is the time and all other variables are as previously defined.

Substituting the expression for d obtained above, we get:

v_i^2 / 0.784 = v_it + 0.5(-0.392)*t^2

Solving for t, we get:

t = (2 * v_i) / 0.392

We still need to find the value of v_i, the initial velocity of the child at the bottom of the hill. To do so, we can use conservation of energy. The child starts at rest at the top of the hill, so all the initial energy is potential energy. At the bottom of the hill, all the potential energy has been converted to kinetic energy. Assuming no energy is lost to friction, we can equate these two energies:

mgh = 0.5mv_i^2

where m is the mass of the child, g is the acceleration due to gravity (9.8 m/s²), and h is the height of the hill.

Solving for v_i, we get:

v_i = √(2gh)

Substituting this expression for v_i into the expression for t obtained earlier, we get:

t = (2 * √(2gh)) / 0.392

Plugging in the values of g, h, and a, we get:

t = (2 * √(29.820)) / 0.392 = 8.04 seconds

A student walks 1.0 kilometer due east and 1.0 kilometer due south. Then
she runs 2.0 kilometers due west. The magnitude of the student's
resultant displacement is closestto
A. 3.4 km
B. 1.4 km
C. 4.0 km
D. O km

Answers

The resulting displacement will be 3.4 km. The correct option is A.

How to calculate the displacement?

The displacement is calculated by finding the displacement from east to west, which is 2.0 km, and subtracting the displacement from north to south, which is 1.0 km.

A student walks 1.0 kilometers due east and 1.0 kilometers due south. Then she runs 2.0 kilometers due west. The magnitude of the student's resultant displacement is closest to 3.4 km.

To begin with, we may use the Pythagorean Theorem to determine the resultant displacement's magnitude. The Pythagorean Theorem is a formula that is used to determine the length of a right triangle's sides when one is missing. This theorem is used to calculate the magnitude of the resultant displacement, which is a quantity. It's a good idea to draw a diagram to help you understand the problem.

Here's a rough sketch of the scenario: We will now apply the Pythagorean theorem in this way: The resultant displacement's magnitude is 3.4 kilometers. Thus, the correct option is A.

To know more about displacement follow

https://brainly.com/question/14637077

#SPJ11

Help asaaap it's about doppler effect

Answers

The frequency that the bad guy hear is 12000 hz when the police car is moving with speed of 80m/s.

Frequencyfo=fs(vvov), where fo is the observed frequency, fs is the source frequency, v is the speed of sound, vo is the observer's speed, the top sign indicates the observer is approaching the source, and the bottom sign indicates the observer is leaving the source.Equation fo=800(80-65) fo = 12000 after substituting the variablesThe apparent change in frequency of a wave as a result of an observer moving with respect to the wave source is known as the Doppler effect or Doppler shift. It bears the name of the Austrian physicist Christian Doppler, who first described the phenomenon in 1842.

For more information on doppler effect kindly visit to

https://brainly.com/question/15318474

#SPJ1

as a source of blackbody radiation becomes hotter, the peak in its radiation spectrum moves from the visible to the ultraviolet and beyond. does this imply that the object can no longer be seen by the unaided human eye

Answers

Yes, it is correct that when the source of blackbody radiation becomes hotter, the peak in its radiation spectrum shifts from the visible to the ultraviolet and beyond. Blackbody radiation is electromagnetic radiation emitted from a blackbody or perfect absorber. This is due to the fact that hotter objects emit shorter wavelengths of electromagnetic radiation, which correspond to higher energy photons. Therefore, when an object gets hot enough to emit mostly ultraviolet or X-ray radiation, it will no longer be visible to the unaided human eye because the human eye can only detect radiation within the visible spectrum of about 400 nm (violet) and 700 nm (red). Therefore, a blackbody that emits radiation beyond this range will no longer be seen by the unaided human eye.

For more information regarding this topic, you can click the below link

https://brainly.com/question/893656

#SPJ11

The electric flux through a spherical surface is4.3×104 N⋅m2/C. What is the net charge enclosed by the surface? The net charge enclosed by the surface isμC. The electric flux through a cubical box34 cmon a side is7.5×103 N⋅m2/C. What is the total charge enclosed by the box? The total charge enclosed by the box isμC

Answers

For the electric flux through a spherical surface is 4.3 x 10⁴ N⋅m²/C, then the net charge enclosed by the surface is μC, and for the electric flux through a cubical box 34 cm on a side is 7.5 x 10³ N⋅m²/C, the total charge enclosed by the box is μC.

The electric flux through a spherical surface is 4.3 x 10⁴ N⋅m²/C.

The net charge is Electric Flux = Charge / Surface Area,

so the net charge enclosed is 4.3 x 10⁴ / (4πr²) where r is the radius of the sphere.

Therefore, the net charge enclosed by the surface is μC.

The electric flux through a cubical box 34 cm on a side is 7.5 x 10³ N⋅m²/C.

The total charge is Electric Flux = Charge / Surface Area,

so the total charge enclosed is 7.5 x 10³ / (6a²)

where a is the length of one side of the cube.

Therefore, the total charge enclosed by the box is μC.

Learn more about electric flux here:

https://brainly.com/question/2664005

#SPJ11

Given the definition of EER, find the EER of an 8000 Btu/hour air conditioner that requires a power input of 1500 W. Express your answer numerically in British thermal units per hour per watt. EER = __________(Btu/hour)/W

Answers

EER is defined as the Energy Efficiency Ratio which is the ratio of cooling capacity in BTU/hr to the power input in watts.

The EER of the given 8000 Btu/h air conditioner is 5.33 Btu/hour per watt.

In the case of the given 8000 Btu/h air conditioner that requires a power input of 1500 W, the EER can be calculated as follows:

EER = (cooling capacity in Btu/hr) / (power input in watts)

EER = 8000 Btu/hour / 1500 W = 5.33 Btu/hour per wat.

Energy efficiency ratio (EER) is used in the USA and is defined as the system output in Btu/h per watt of electrical energy.

Coefficient of performance (COP) is the equivalent measure using SI units, which is widely used in the UK. A COP of 1.0 equates to an EER of 3.4.

To know more about power:https://brainly.com/question/11569624

#SPJ11

what state of matter is rutherfordium in while at room temperature

Answers

Rutherfordium is a synthetic element with the atomic number 104 and symbol Rf. As a synthetic element, it is not found naturally on Earth and is produced through nuclear reactions in laboratories.

Rutherfordium is a member of the transition metals group and is expected to have similar physical and chemical properties to its neighboring elements in the periodic table. However, due to its radioactive nature and short half-life, its physical properties are difficult to determine.

While there is no experimental data available on the state of matter of rutherfordium at room temperature, it is expected to be a solid metal, similar to other transition metals, such as copper or nickel.

To learn more about matter refer to:

brainly.com/question/28591826

#SPJ4

in one cycle a heat engine absorbs 480 j from a high-temperature reservoir and expels 320 j to a low-temperature reservoir. if the efficiency of this engine is 56% of the efficiency of a carnot engine, what is the ratio of the low temperature to the high temperature in the carnot engine?

Answers

The ratio of the low temperature to high temperature of the Carnot engine is 2.38.

What is the efficiency of Carnot engine?

The efficiency of the Carnot engine can be defined as the ratio of network done per cycle by the engine to the heat energy absorbed by the engine per cycle by the working substance from the source.


Efficiency = 1 - (Tlow/Thigh)


Heat absorbed by engine = 480J

Heat expelled by engine = 320J

Efficiency of the engine = 56% of efficiency of Carnot engine

The ratio of low temperature to high temperature in the Carnot engine.

Let's assume the efficiency of the Carnot engine is 'ηc' = 1 - T₂/T₁

Where, T₂ = Low temperature and T₁ = High temperature

To calculate the efficiency of the engine given, η = (Q1 - Q2)/Q1

η = (480 - 320)/480

η = 160/480

η = 1/3

η = 33.33%

Now, η = 56% × ηc

0.56ηc = 1/3ηc = (1/3)/0.56 = 0.58

As we already know, ηc = 1 - T₂/T₁

T₂/T₁ = 1 - ηc

T₂/T₁ = 1 - 0.58

T₂/T₁ = 0.42

T₁/T₂ = 1/0.42

T₁/T₂ = 2.38

Therefore, the ratio of low temperature to high temperature in the given Carnot engine with an efficiency of 56% will be about 2.38.

Learn more about Carnot engine here:

https://brainly.com/question/14680478


#SPJ11

A student must analyze data collected from an experiment in which a block of mass 2M traveling with a speed vo collides with a block of mass M that is initially at rest. After the collision, the two blocks stick together. Which of the following applications of the equation for the conservation of momentum represent the initial and final momentum of the system for a completely inelastic collision between the blocks? Justify your selection. Select two answers. A. 2Mo = 3Muf, because the blocks stick together after the collision.
B. 3Mvo = 3MUf, because the blocks stick together after the collision. C. 2MVo = 2MU + Muf, because the blocks stick together after the collision. D. 2MVo = M0o + 3 Muf, because the blocks do not stick together after the collision.

Answers

A student must analyze data collected from an experiment in which a block of mass 2M traveling with a speed vo collides with a block of mass M that is initially at rest. After the collision, the two blocks stick together. Thus, the correct options are A and B.

What is Momentum?

The initial momentum of the system = the momentum of block 1 = (2M)vo. The final momentum of the system = the momentum of the combined blocks = (2M + M)uf = 3Muf. Therefore, the correct applications of the equation for the conservation of momentum that represent the initial and final momentum of the system for a completely inelastic collision between the blocks are:

2Mo = 3Muf, because the blocks stick together after the collision. 3Mvo = 3MUf, because the blocks stick together after the collision.

Therefore, the correct options are A and B.

Learn more about Momentum here:

https://brainly.com/question/30677308

#SPJ11

Discuss three applications of the effects of surface tension.​

Answers

1. Surface tension: is the property of the liquid by virtue of which the free surface of liquid at rest tends to have minimum surface area and as such it behaves as if covered with a stretched membrane.

2. Effect of Surface tension:
Surface tension of soap solution is less, it can spread over large areas and wash clothes more effectively, since the dirt particles stick to the soap molecules.
In soldering, addition of flux reduces the surface tension of molten tin. Hence, it spreads.
Antiseptics like dettol have low surface tension, so that they spread faster.
Surface tension prevents water from passing through the pores of an umbrella.
A duck is able to float on water as its feathers secrete oil that lowers the surface tension of water.

in the heliocentric model of the solar system, one planet passing another in its orbit gives rise to ...

Answers

In the heliocentric model of the solar system, one planet passing another in its orbit gives rise to gravitational forces.

It can also lead to an alteration in the planets' orbits. This is due to the gravitational forces produced by the interaction between the planets. A heliocentric model is a model of the solar system in which the sun is at the center and the planets orbit it. This model was first proposed by Nicolaus Copernicus, a Polish astronomer in the 16th century. He proposed this model after observing that it better explained the motions of the planets than the previous geocentric model, in which Earth was at the center and everything else revolved around it. An orbit gives rise to the gravitational force that causes a planet to continue to travel in a circle around the sun. It is also responsible for the gravitational pull between planets, which affects their orbits. A planet passing another planet in its orbit can also cause some gravitational perturbations in its orbit. This can lead to an alteration in the planets' orbits or cause their orbits to change slightly over time. The heliocentric model is currently the widely accepted theory of how our solar system is arranged. It states that the planets orbit the sun, which is a massive ball of hot gas at the center of the solar system. The sun's gravity is what keeps the planets in their orbits.

Learn more about the heliocentric model  at brainly.com/question/19757858

#SPJ4

When using compass orientation, migrating animals make use of _____.a. memories from previous trips with parentsb. familiar landmarks and olfactory cuesc. the north and south polesd. the sun, stars, and Earth's magnetic field

Answers

When using compass orientation, migrating animals make use of the sun, stars, and Earth's magnetic field to navigate. So, option d is correct option.

Compass orientation in migrating animals is the process of using the sun, stars, and Earth's magnetic field to navigate. Migrating animals use a variety of techniques to navigate, depending on their species and environment.

Some animals use the position of the sun, stars, and Earth's magnetic field as their primary means of orientation when migrating. This is known as compass orientation.

Compass orientation is a technique that relies on environmental cues, such as the position of the sun and stars, to determine direction. Some animals can use the Earth's magnetic field to navigate as well. This is known as magnetic orientation.

Magnetic orientation is used by some species of birds and fish, as well as certain insects and reptiles. Other animals use landmarks and olfactory cues to navigate.

These animals rely on visual or chemical markers in the environment to orient themselves. This technique is known as piloting. Piloting is used by animals such as rodents, bats, and some species of birds. Animals that use piloting must be able to remember and recognize the landmarks they use as cues to navigate.

Finally, some animals use memories from previous trips with parents to navigate. This technique is known as true navigation. True navigation requires animals to have a highly developed sense of spatial awareness and memory. True navigation is used by animals such as sea turtles and some species of birds.

All of these techniques require different cognitive abilities and sensory mechanisms, but they allow animals to navigate over long distances to reach their desired destinations.

for similar question on magnetic field to navigate.

https://brainly.com/question/22986969

#SPJ11

why is a polarized filter helpful to a photographer? A. it transmits all light

Answers

Answer:

It blocks some light, but not all.

Explanation:

The point of polarization is to get the light to travel in a single plane. The light waves occur in a single plane. The direction of the vibration of the waves is the same. With two polarized filters, it is possible to block out nearly all the light.

Other Questions
true or false? pre-employment drug testing, now a relatively common practice in health care recruiting, can help screen out people who might be prone to workplace violence. When a mineral breaks along a weekly bonded plane it is called A fertile valley has farms and a small town. The valley is surrounded by hills, but these hills are not good for farming or living. Over time, the town expands.How will the towns growth most likely affect the availability of farmland in the valley?1. The availability of farmland will decrease. 2. The availability of farmland may increase or decrease.3. The availability of farmland will remain unchanged.4. The availability of farmland will increase. When firms restructure their operations to decrease production costs, the aggregate supply curve, the price level, and real output will change in which of the following ways? Aggregate Supply Curve / Price Level / Real OutputShift to the left Increase IncreaseShift to the left Increase No changeShift to the right Increase IncreaseShift to the right Decrease IncreaseShift to the right Decrease Decrease When using compass orientation, migrating animals make use of _____.a. memories from previous trips with parentsb. familiar landmarks and olfactory cuesc. the north and south polesd. the sun, stars, and Earth's magnetic field Angela compro un terreno rectangular que tiene un perimetro de 10x - 28aSi el ancho del terreno es 2x - 4a Cual es la expresin que muestra la medida del largo del terreno? According to research on intergenerational relationships, in which of the following ways is an adult child most likely to be similar to his or her parents?Select one:A. In gender rolesB. In politicsC. In lifestyleD. In work orientation A student takes a multiple-choice test that has 10 questions. Each question has four choices. The student guesses randomly at each answer. Round the answers to three decimal places Part 1 of2 (a) Find P(5) P(5)- Part 2 of2 (b) Find P(More than 3) P(More than 3) Solve for x,using the tangent lines.X42x = [?]can someone pls help explain how they got the answer? im having a hard time understanding, ty :) you are computing a confidence interval for the difference in 2 population proportions. which of the following could be negative? select all.OP1Op 1 - 2Standard errorCritical valueLower bound of the confidence intervalUpper bound of the confidence interval A school has 1800 pupils. 55% of the pupils are girls. 30% of the girlsand 70% of the boys travel by bus. a) How may girls travel by bus? b) How many boys travel by bus?c) What percentage of the pupils travel by bus? a semiannual coupon bond with a coupon rate of 9% and face value of $1000 trades at $900. it matures in 15 years. what is its yield to maturity (ytm)? Mr. Lowe is a network administrator who plans on purchasing a switch that will be the part of a network for a new fast-growing fast food joint named Momos & More (M&M). The team at M&M has specifically told Mr. Lower that even though the current need of the network is two fiber-optic connections, it is planning on a significant expansion in the coming years. This expansion will include a fiber-topic connectivity to every desktop in the organization. Analyze what Mr. Lowe should do in this situation.a. Order a switch with the current demand numberb. order switches that allow upgradeable interfacesc. order media convertorsd. use APC ferrules 93. Electricity Usage The graph showsthe daily megawatts of electricity usedon a record-breaking summer day inSacramento, California.(a) Is this the graph of a function?(b) What is the domain?(c) Estimate the number of megawattsused at 8 A.M.(d) At what time was the most electric-ity used? the least electricity?(e) Call this function f. What is f(12)?Interpret this answer.(f) During what time intervals is usageincreasing? decreasing? an american politician and attorney who is the 49th and current vice president of the us. she is the first female and first african american vp, who is she? Describe the evolution of the Auschwitz concentration camps in 3-5 sentences we are too late . The train. _________ (leaving) Determine the total amount of money that was utilized on fuel in June 2022 a student pulls a 1500 kg suitcase along a flat sidewalk. if the cord on the suitcase breaks when the force is greater than 50n, what is the maximum acceleration that the student can achieve with the suitcase? What is first-strand synthesis of cDNA?