Answer:
A. not wearing goggles when breaking a rock with a hammer
Explanation:
You could get extremely hurt if you are not wearing goggles while doing lab work.
The action that reflects irresponsible lab safety behavior is not wearing goggles when breaking a rock with a hammer. Thus, the correct option for this question is A.
What are Lab safety behaviors?Lab safety behaviors may be defined as those actions and habits that are persistently taken by individuals in order to maintain discipline and safety on their own. Some of the lab safety behaviors are as follows:
Avoid skin and eye contact with all chemicals by wearing gloves and goggles.Follow an accurate protocol during an experiment. Beware of all safety showers, eye washers, and fire extinguishers. Avoid eating, drinking, and unnecessary talking in the lab.Never smell or inhale laboratory chemicals.Some of the lab safety behaviors also include not shaking hands with your lab partner after a successful experiment, not sharing findings and recordings with the general public, etc. This is because these are some private sources of information.
Therefore, the action that reflects irresponsible lab safety behavior is not wearing goggles when breaking a rock with a hammer. Thus, the correct option for this question is A.
To learn more about Lab safety behaviors, refer to the link:
https://brainly.com/question/8430576
#SPJ2
3. Trees, bananas, skateboards and pancakes are all solids. They have
atoms that are closely packed together and don't move around very
much. Solids also have definite shape, mass and volume. "Definite"
means that it doesn't easily change. When you pour cereal into a bowl,
the pieces of cereal don't change shape. But when you pour milk into a
bowl, the milk takes the shape of the bowl. That's because cereal is a
solid.
A
Which of the following is an example of a solid?
A. applesauce
Corange juice
B. watermelon
D. berry smoothie
Answer:
B. Watermelon
Explanation:
Watermelon is the only option with a definite shape that wouldn't change if you put it in a bowl
Which statement best describes liquid water and water vapor at equilibrium?
A. Liquid water stops entering the gas phase.
O B. The concentration of liquid water equals the concentration of
water vapor.
C. The concentrations of liquid water and water vapor are stable.
D. The concentration of liquid water is zero.
C. The concentrations of liquid water and water vapor are stable. it describes the fact that liquid water and water vapor are at equilibrium.
EquilibriumAn equilibrium is achieved when no more water vapor can enter into the gas phase from the liquid water during evaporation process. This happens when a saturation is attained between liquid water and the vapor phase.Hence, option (c) is correct. The concentration of liquid water and water vapor will become stable.
Learn more about water vapor:
https://brainly.com/question/17259832
How is gold related to suns life cycle?
Answer: Gold is shiny and bright just like the sun. Gold is yellow.
Explanation:
Image by e2020
In the diagram, the lines dividing the parking spaces are parallel. What must be true about 1 and 22? What theorem
supports your conclusion?
A. 21 and 22 are supplementary; alternate exterior angles theorem
B. 21 22; alternate exterior angles theorem
C. 21 and 22 are supplementary; consecutive exterior angles theorem
D. Z1 Z2; consecutive exterior angles theorem
Mark this and return
Save and Exit
Next
Submit
Answer:
B. ∠1 ≅ ∠2; alternate interior angles theorem
Explanation:
Assume the diagram is like the one below.
The blue lines are parallel, and the red line is a transversal.
∠s 1 and 2 are between the parallel lines but on opposite sides of the transversal.
They are alternate interior angles.
Pairs of alternate interior angles are congruent.
A. is wrong. Alternate interior angles are congruent.
C. is wrong. Consecutive exterior angles are outside the parallel lines and on the same side of the transversal. They are like the two angles marked with a blue x. They are supplementary.
D is wrong. Consecutive exterior angles are supplementary.
I just need the answer please to both if you can
Answer:
No.4 is B No.5 is d
Explanation:
Answer:
Q 4: d
Explanation: this is all I can answer
What is the key building block of living tissue and ecosystems?
Hope u can help!
Answer:
Your answer is cells. Hope this helps!
A weather forecast shows 35 m/h on the weather map. Which weather component does this number represent?
A.Humidity
B. Precipitation
C.Wind direction
D.Wind speed
Answer:
D. Wind Speed
Explanation:
When the question brings up 35 m/h, the m/h stands for Miles per Hour. What option can you measure the miles per hour. Here's a hint, it applies to cars as well when cops give your parents speeding tickets. Miles per Hour = Speed. So, you are measuring the wind speed.
Consider a system of four gases. The equilibrium concentration of each product is 2.3 M and the equilibrium concentrations of the reactants are equal. The equilibrium is shown here:
A + B C + D K = 2.6
What is the equilibrium concentration of gas A?
Answer:
The equilibrium concentration of gas A is 1.43 M
Explanation:
Here we have the reaction expressed as follows;
A + B → C + D and
The formula for equilibrium constant is therefore presented as follows;
[tex]K = \frac{[C]\times [D]}{[A]\times [B]}[/tex]
Where:
[C] = [D] = 2.3 M
[A] = [B]
K = 2.6
Hence, we have;
[tex]2.6 = \frac{2.3\times 2.3}{[A]\times [A]} = \frac{5.29}{[A]^2}[/tex]
[tex][A]^2= \frac{5.29}{2.6} = 2.03[/tex]
[A] = 1.43 M
The equilibrium concentration of gas A = 1.43 M.
Answer:
The equilibrium concentration of gas A = 1.43 M
Explanation:
First set up the equilibrium expression:
[tex]K = \frac{[C]\times [D]}{[A]\times [B]}[/tex]
The problem states that each product has a concentration of 2.3M at equilibrium, and that k=2.6
We also know that [A] and [B] are the same.
Since we are solving for [A] I'm going to change [A][B] to A²
[tex]2.6 =\frac{2.3^2}{A^2}[/tex]
Now we just need to solve for A²
A² = 5.29 / 2.6
A² = 2.0346
A = √2.0346
A = 1.43
Therefore, the equilibrium concentration of gas A = 1.43 M.
The addition of heat causes the individual particles of a solid to
Answer:
Move rapidly or move fast and farther apart. Hope this helps.
Answer: vibrate more rapidly
Explanation:
How many Liters are in 17.3 moles of Iron?
Answer:
There are 0.12269 Liters of Iron
Explanation:
First, by means of the molecular weight equation, the grams of iron corresponding to 17.3 moles can be calculated:
[tex]MW=\frac{mass(grams)}{moles}[/tex]
[tex]mass=MW*moles=55.845\frac{g}{mol} *17.3mol=966.119 g[/tex]
Then using the density equation the iron milliters are calculated:
[tex]d=\frac{mass(g)}{volume(mL)}[/tex]
[tex]volume=\frac{mass}{density}=\frac{966.119g}{7.874\frac{g}{mL} } =122.69 mL[/tex]
Milliliters to liters are converted:
122.69 mL = 0.12269 L of Iron.
Answer:
[tex]V_{Fe}=0.125L[/tex]
Explanation:
Hello,
In this case, given the moles of iron, we need to use it atomic mass (55.845 g/mol) and density (7.874 g/cm³) in order to firstly convert from moles to grams and secondly from grams to cubic centimetres:
[tex]V_{Fe}=17.6molFe\times \frac{55.845gFe}{1molFe}*\frac{1cm^3}{7.874gFe}=124.8cm^3[/tex]
Finally, we obtain the volume in litres by:
[tex]V_{Fe}=124.8cm^3*\frac{1L}{1000cm^3} \\\\V_{Fe}=0.125L[/tex]
Best regards.
Adding concentrated
sulfuric acid to sugar
What reaction is this?
Answer:
Dehydration of Sugar
Explanation:
Identifying Ways Rocks Change in the Rock Cycle Cycle of a rock. Arrows point from one stage to the next. Stage A, small, brown granules, to Compaction and cementation or Stage C. Arrow labeled Heat and pressure from Stage C to B, larger gray rocks. Arrow labeled Melting from Stage B to Magma. Arrow labeled Cooling from Magma to Igneous Rock. Arrow labeled Melting from Igneous Rock to Magma. Stage D arrows from Igneous Rock to Stage A, from Stage B to A, and from Stage C to A. Using the drop-down menus, label the parts of the rock cycle.
A- sediment, sedimentary rock, or metamorphic rock
B- sediment, sedimentary rock, or metamorphic rock
C- sediment, sedimentary rock or metamorphic rock
D- compaction and cementation, heat and pressure, or weathering and erosion
Answer:
sediment, metamorphic rock, sedimentary rock, weathering and erosion
Explanation:
for edge 2020
hope this helps
HAVE A GREAT DAY : )
Sediment, sedimentary rock, or metamorphic rock are the parts of the rock cycle. Therefore, the correct option is option A.
What are sedimentary rock, and metamorphic rock?Sedimentary rocks are created by the aggregation or deposition of organic or mineral particles at the Earth's surface, following by cementation. Sedimentation refers to the mechanisms that lead these grains to settle in situ.
Any of a family of rocks formed by the modification of pre - existing rocks in reaction to changing environmental circumstances, such as temperature, pressure, or mechanical stress, as well as the addition or deletion of chemical components is metamorphic rock. Sediment, sedimentary rock, or metamorphic rock are the parts of the rock cycle.
Therefore, the correct option is option A.
To know more about rock, here:
https://brainly.com/question/29767269
#SPJ2
How can the motion of atoms in the solid state of most substances be described?
Answer:
The molecules in a solid are stuck in a specific structure or arrangement of atoms. The atoms still vibrate and the electrons fly around in their orbitals, but the entire atom will not change its position.
An ideal gas, such as helium, is in a sealed container made of hard steel. If the container is heated, what would happen to the gas trapped inside the container?
Group of answer choices
The volume of the gas will decrease
The pressure of the gas will increase
The volume of the gas will increase
The pressure of the gas will decrease
Answer:
The correct answer is The pressure of the gas will increase
The volume of the gas will increase
Explanation:
Step 1: Data given
The gas in a container is heated, this means the temperature increases
Suppose we start with a temperature of 100 K and a pressure of 1 atm and a volume of 1L
Step 2:
V1/T1= V2/T2
⇒V1 = the initial volume = 1L
⇒T1 = the initial temperature = 100 K
⇒V2 = the new volume = TO BE DETERMINED
⇒T2 = the increased temperature = 200 K
1/100 = V2 / 200
V2 = 2 L
This means when the temperature increases, the volume will increase
P1/T1 = P2/T2
⇒P1 = the initial pressure = 1 atm
⇒T1 = the initial temperature = 100 K
⇒P2 = the new pressure = TO BE DETERMINED
⇒T2 = the increased temperature = 200 K
1/100 = P2 / 200
P2 = 2 atm
This means when the temperature increases, the pressure will increase
The correct answer is The pressure of the gas will increase
The volume of the gas will increase
What slows down heat energy from escaping the Earth?
Answer:
Greenhouse gases such as carbon dioxide and water vapor make an atmosphere around the earth and make less heat escape
Explanation:
Which is usually associated with a faster reaction rate?
A. diluting a solution of the reactants
B. adding modeling clay to the reactants
C. removing heat energy from the reactants
D. using a solid with a high surface area in the reactants
Answer:
D. using a solid with a high surface area in the reactants, is your correct answer.
Explanation:
Using a solid with a high surface area in the reactants is usually associated with a higher reaction rate.
A gas was held at a constant temperature in a closed system. The initial
pressure of the gas was 1.20 atm, while its initial volume was 2.30 L. The
final volume of the gas was 1.50 L. What was the final pressure of the gas
to the nearest hundredth of an atmosphere?*
Answer:
1.84 atm
Explanation:
P2=V1P1/V2
Temp is irrelevant because it is constant, so all you have to do is rearrange the ideal gas law.
You can check this by knowing P and V at constant T have an inverse relationship and therefore makes this the correct answer.
- Hope that helps! Please let me know if you need further explanation.
What does X represent for this transmutation?
96242Cm + X→ 98245Cf + 01n
gamma
+10e
24He
−10e
Answer:
24He
Explanation:
When a nuclide is bombarded with alpha particles, we notice an increase in its mass and charge since an alpha particle has a mass of four and a charge of +2. recall that nuclear equations must be balanced. That is, the masses and charges on the left hand six and the right hand side of the nuclear reaction equation must be exactly the same.
Looking at the nuclear reaction at hand, the total mass on the left hand side has to be 246 while the total charge on the left hand side of the equation will be 98. Coming over to the right hand side, the total masses are also found to be the same as a neutron with no charge and a mass of 1 is produced. Hence the nuclear reaction equation is balanced when an alpha particle (helium nucleus) is substituted for X in the equation.
Answer:
24HE
I took the test!
Two objects, labeled A and B, are the same size. Object A has a density of 1.21 g/cm3. Object B has a density of 1.37 g/cm3. Both are placed in a beaker of water. Which will float higher in the water?
Answer:
object a will float higher because it has less density.
Explanation:
Answer:
object a will float higher because it has less density.
Explanation:
A curved piece of glass or other transparent material that is used to refract light is called a (an) _____.
A) mirror
B) lens
C) reflector
D) optical fiber
Answer:
Lens
A curved piece of glass or other transparent material that is used to refract light.
Explanation:
u got ig?
A curved piece of glass or other transparent material that is used to refract light is called a lens. The correct option is B).
What are lenses?A curved piece of transparent material, such as glass, that bends light is called a lens. A lens's shape and the object's position both affect the kind of image it produces.
The center of a concave lens is thinner than the edges. Bent glass is defined as glass that has been curved or bent into a convex or concave shape. The desired shape is created by gently heating the glass until it becomes pliable, then molding it into that shape.
Light is refracted through lenses. When a light beam enters a lens, it is refracted; then, when it leaves the lens, it is refracted once more.
Therefore, the correct option is the B) lens.
To learn more about the lens, refer to the link:
https://brainly.com/question/766997
#SPJ2
Why would the pressure of a sample of gas at a constant volume fall .10 atm?
Answer:
As the temperature of a sample of gas falls from 45.0ºC to 30.0ºC, its pressure falls to 300.
Explanation:
Why were scientists surprised to find coal in the arctic?
Answer:
coal is made from compressed plant matter and how exactly did plants grow on the surface of an ocean. (as there is no land mass beneath the arctic.)
Explanation:
it would be like finding a fly in an ice cube to simplify it.
They were surprised to find coal in arctic because ordinarily coal was supposed to be found in warm or hot environments and not cold region like the arctic.
The arctic is located at the far northern part of the world which is characterized by its extreme cold weather.
A limited vegetation of plants such as grasses, mosses and lichens are found in this region irrespective of the extreme cold weather through out the year.
Coal is a type of fuel gotten from fossils and deposits of plant vegetation.
Scientist has discovered that continents do move over time through a process called continental drift. This is the reason why limited vegetaion is found in the arctic leading to the formation of coal.
Learn more here:
https://brainly.com/question/22647554
I AM GIVING BRAINLIEST PLEASEE HELPPPP I NEED HELPPPPPP PLEAEEEEEE
63.2 g of BaCl 2 are dissolved in enough water to make a 634 mL solution. What is the molarity?
Answer:
0.479 M or mol/L
Explanation:
So Molarity is moles/litres of solution...often written as M=mol/L
So here we are given grams of BaCl2 which we have to convert to moles. To convert to moles of BaCl2 we have to divide 63.2 g BaCl2 by molar mass of BaCl2 which is 208.23 g/mol so you get 63.2/208.23 = 0.3035 moles of BaCl2
Second step is converting the 634mL to litres by simply dividing by 1000 because we know 1 litre has 1000ml so 634/1000 = 0.634L
Now we just plug these guys in our molarity formula M=mol/L
M= 0.3035/0.634 = 0.479 M or mol/L
Answer:
Interestingly enough, I'm not getting
0.0341% w/v
either. Here's why.
Start by calculating the percent composition of chlorine,
Cl
, in calcium chloride, This will help you calculate the mass of chloride anions,
Cl
−
, present in your sample.
To do that, use the molar mass of calcium chloride, the molar mass of elemental chlorine, and the fact that
1
mole of calcium chloride contains
2
moles of chlorine atoms.
2
×
35.453
g mol
−
1
110.98
g mol
−
1
⋅
100
%
=
63.89% Cl
This means that for every
100 g
of calcium chloride, you get
63.89 g
of chlorine.
As you know, the mass of an ion is approximately equal to the mass of the neutral atom, so you can say that for every
100 g
of calcium chloride, you get
63.89 g
of chloride anions,
Cl
−
.
This implies that your sample contains
0.543
g CaCl
2
⋅
63.89 g Cl
−
100
g CaCl
2
=
0.3469 g Cl
−
Now, in order to find the mass by volume percent concentration of chloride anions in the resulting solution, you must determine the mass of chloride anions present in
100 mL
of this solution.
Since you know that
500 mL
of solution contain
0.3469 g
of chloride anions, you can say that
100 mL
of solution will contain
100
mL solution
⋅
0.3469 g Cl
−
500
mL solution
=
0.06938 g Cl
−
Therefore, you can say that the mass by volume percent concentration of chloride anions will be
% m/v = 0.069% Cl
−
−−−−−−−−−−−−−−−−−−−
I'll leave the answer rounded to two sig figs, but keep in mind that you have one significant figure for the volume of the solution.
.
Explanation:
Which of these structures are found in plant cells but not animal cells?
A. Gogi apparatus
B. mitochondria
C. lysosomes
D. cell wall
Answer:
A
Explanation:
Answer:c
Explanation:
Which of the following best describes the main function of the nervous system?
To deliver nutrients and other essential materials to cells and remove waste products
To break down the nutrients found in food so that they can be used by all cells in the body
To produce the chemical signals that allow parts of the body to communicate over long distances
To coordinate all other body systems so that they can function together to maintain homeostasis
balance the following equation:
!!!!
Answer:
CaC2 + 2H2O > C2H2 + Ca(OH)2
Explanation:
Count the amounts of Ca, C, H, and O, all separately on both sides.
Ca: 1 Ca: 1
C: 2 C:2
H: 2 H: 4
O: 1 O: 2
Now, your goal is to get both sides equal to each other by adding a 2 in front of H2O.
18. Which statement best describes the balanced chemical equation?
Answer:
It is endothermic and entropy increases.
Explanation:
What is the purpose of the part of the male reproductive system that is
highlighted below?
A. Mixes sperm and semen
B. Creates the fluid in semen
C. Manufactures sperm cells
D. Stores sperm cells until they mature
O
Answer:
A
Explanation:
Unlike the female reproductive system, the most parts of the male reproductive system are located outside the body. The mentioned part in the given diagram is urethra and it Mixes sperm and semen. The correct option is A.
What is male Reproductive system?The male reproductive system includes the testes, scrotum, spermatic ducts, male accessory glands and phallus. All these organs work together to produce sperms, the male gamete, male sex hormones and other components of semen.
The phallus and urethra are the parts of both the reproductive and urinary systems. Scrotum, seminal vesicles, vas deferens, testicles and prostate constitute all the remaining male reproductive system.
The urethra is a tube like structure which is the region included in the urinary tract that takes the urine from the bladder where the semen is ejaculated.
Thus the correct option is A.
To know more about male reproductive system, visit;
https://brainly.com/question/940283
#SPJ7
Which resulted from the study of chemistry?
A) Alchemy to turn base metals into noble metals
B) the understanding of earth, air, fire, and water as the basic components of matter.
C) discovering the role of oxygen in combustion
D) a supernatural, mystical view of the world
Referencing the reasoning you used from #1, explain the difference between objects that feel hot and those that
feel "cold".
Answer:
The temperature of the cold water is lower than the warm one. So, when we put the hand in the warm from the cold water, our hand will absorb heat, causing the hand to feel hot. Thus, we can conclude that the more heat it absorbs, the more hotter it is. Whereas the more heat it releases, the colder it is.
