Observe and compare the forces acting on the turtle and the cat.
a turtle and a cat on the ground looking at each other and not moving
1. The forces are balanced on both animals because they are not moving.
2. The forces are unbalanced on both animals because they are not moving.
3. The forces are balanced on the turtle but unbalanced on the cat because it is heavier.
4. The forces are balanced on the cat but unbalanced on the turtle because the cat is larger.

Answer:

It would triple.

Explanation:

By Newtown's law of universal gravitation, the ration is 1:1

The tension in the right-hand side wire is 6525 N.

Given:

To find: Tension in the right-hand side wireWe know that the sum of forces acting in a vertical direction should be equal to 0 as there is no acceleration in the vertical direction. ∑Fv = 0In the horizontal direction, there are no forces acting on the system.

∑Fh = 0Now considering forces in the vertical direction: T1 + T2 = (Weight of scaffold + Weight of the box) gT1 + T2 = (180 + 580) x 9.8T1 + T2 = 7644 N1. From the diagram, we can see that the box is nearer to the left side. Hence, the tension force in the left wire is greater than the tension force in the right wire.

T1 > T22. Let's take moments about the right end of the scaffold as shown in the figure below.

Now, we can substitute the value of T2 in equation (1):

To find T2, we can substitute the value of T1 in equation (2):

Therefore, the tension in the right-hand side wire is 6525 N.

Learn more tension: https://brainly.com/question/4001686

#SPJ11

At the shop, Joselyn purchased 2700 grammes of salt water taffy.

To convert kilograms (kg) to grams (g), Joselyn would need to multiply the weight in kilograms by 1000. This is because there are 1000 grams in 1 kilogram. Therefore, to find out how many grams of salt water taffy Joselyn bought, she would need to multiply 2.7kg by 1000.

The correct answer is (B) Multiply by 1000.

Multiplying 2.7kg by 1000 gives:

2.7kg x 1000 = 2700g

So Joselyn bought 2700 grams of salt water taffy at the store.

To learn more about salt water refer to:

brainly.com/question/6829606

#SPJ4

When only one lightbulb blows out, an entire string of decorative lights goes out, which means that the lights in this string must be connected in series with one current pathway.

In a series circuit, the components are connected end to end in a single path, so the current flows through each component in turn. If one component, such as a lightbulb, fails, the circuit becomes incomplete, and the current cannot flow through any of the components downstream of the failed component. This results in all the lights in the series circuit going out when one lightbulb blows out.

In contrast, in a parallel circuit, the components are connected across multiple current pathways, so if one component fails, the current can still flow through the other components, and they will continue to function normally. Therefore, if one lightbulb blows out in a parallel circuit, the other lights will continue to work.

Learn more about the series circuit:

https://brainly.com/question/19865219

#SPJ11

Plants help to reduce water runoff and soil erosion, both of which affect the health of streams and rivers by impacting water quality.

Soil erosion increases the silt load in the water, which can smother living organisms, particularly plants and invertebrate species. Runoff water can carry pollutants, particularly pesticides, and herbicides from agricultural land.

Landscape 1 (streams cutting through small farms with a variety of crop types and natural vegetation buffers between the fields and the streams) would be the best quality, followed by Landscape 2 (a large floodplain area covered in lowland forests and swamps full of emergent vegetation, with small streams cutting through the area) and Landscape 3 (an urban housing development where the streams are surrounded by emergent vegetation).

Learn more about water quality at  brainly.com/question/20848502

#SPJ11

If the object in motion has some magnetic properties or contains a magnet, we can use another magnet to change its direction of motion by exerting a force on it through magnetic interaction. This principle is known as the Lorentz force.

Here's how we can set up the experiment:

Take a magnet and place it on a flat surface.

Take another magnet or the object with magnetic properties that is in motion.

Hold the magnet or the object in your hand and bring it close to the stationary magnet without touching it.

Move the magnet or the object towards the stationary magnet and observe its behavior.

If the magnet or the object has the same polarity as the stationary magnet, they will repel each other, and the motion of the object will be deflected in a direction away from the stationary magnet. If the magnet or the object has opposite polarity to the stationary magnet, they will attract each other, and the motion of the object will be deflected in a direction towards the stationary magnet.

Here's a diagram to help you visualize the setup:

                 N   S          N   S

       __________    __________

      |                       |  |                     |

      |   M1               |  |           M2     |

      |__________|  |__________|

              ( )                             ( )

               |                               |

        Motion              Stationary

        Object                 Magnet

In this diagram, M1 represents the motion object or magnet, and M2 represents the stationary magnet. The N and S represent the North and South poles of the magnets. The arrows indicate the direction of motion and the direction of the magnetic field.

As we move M1 towards M2, the magnetic interaction will exert a force on M1, causing it to change its direction of motion. The direction of deflection will depend on the polarity of the magnets.

Note: It's important to keep in mind that the magnetic force is only one of the many factors that can affect the motion of an object. Other factors such as friction, air resistance, and gravitational forces can also play a significant role.

To know more about  Motion visit :-

https://brainly.com/question/453639

#SPJ1

Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7J and 23.5J, for better understand we have to know the meaning of potential energy.

Potential energy in physics is the energy that an item retains as a result of its location in relation to other objects, internal tensions, electric charge, or other elements. Potential energy develops in systems having components whose configurations, or relative positions, determine the amount of the forces they apply to one another.

Potential Energy of an Object = m * g * h

Where, m = mass,

g = gravity, and

h = height

Potential Energy of Object W = 2 * 9.8 * 0

= 0 J

Potential Energy of Object X = 2 * 9.8 * 0.4

= 7.84 J

Potential Energy of Object Y = 2 * 9.8 * 0.8

= 15.68 J

≈ 15.7 J

Potential Energy of Object Z = 2 * 9.8 * 1.2

= 23.5 J

Therefore, Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7 J and 23.5 J.

To Learn more about Potential Energy, visit:

https://brainly.com/question/1242059

#SPJ1

For calculation of potential energy mass of the apple , average acceleration of the apple and height of apple is required.

For more information on kinetic and potential energy kindly visit to

https://brainly.com/question/11749818

#SPJ1

The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass.

An object-earth system is a system in which an object interacts with the earth by exerting a force of attraction. The object's energy is derived from the work done by gravitational forces when the object is moved away from the earth's surface.

An object in an object-earth system's gravitational potential energy is the work done by gravitational forces on the object when it is moved from a lower position to a higher one in the object-earth system. The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass. The gravitational potential energy of an object in the earth-object system is determined by the distance between the object and the earth's surface. The gravitational potential energy of an object increases as the distance between it and the earth's surface increases.

Learn more about the gravitational potential at brainly.com/question/19768887

#SPJ11

The Volumetric efficiency of the pump is the ratio of the actual capacity to the theoretical capacity of the pump.

Volumetric efficiency of the pump = Actual capacity of the pump / Theoretical capacity of the pump

Given Information

The provided information is,

Find

The theoretical capacity of the pump is given by the following formula,

Theoretical capacity of the pump = π/4 x d² x l x n

where:

For the given problem,

We need to find the diameter of the pump and length of the pump to calculate the theoretical capacity of the pump.

Now, we have the actual capacity of the pump.

As we don't have the diameter and length of the pump, it is impossible to calculate the theoretical capacity of the pump.

Hence, the Volumetric efficiency of the pump cannot be calculated.

Learn more about Volumetric efficiency: https://brainly.com/question/14783214

#SPJ11

The coordinated functions of the Nervous, Endocrine, and Reproductive systems are:

Coordinated functions refer to the integration and communication between different organs, systems, and tissues in the body to achieve a common goal or purpose. In biological terms, coordinated functions often involve multiple physiological systems working together to maintain homeostasis, respond to stimuli, or carry out complex behaviors or processes.

Examples of coordinated functions include the regulation of blood glucose levels by the pancreas and liver, the coordination of movement by the nervous and musculoskeletal systems, and the release of hormones by the endocrine system to control various physiological processes.

Learn more on coordinated functions here: https://brainly.com/question/15686131

#SPJ1

The question is:

"COORDINATED FUNCTIONS OF THE NERVOUS, ENDOCRINE, AND REPRODUCTIVE SYSTEMS"

Directions: Identify the part of the brain that is involved in each situation below. Write only the letter of your answer.

A. Amygdala

B. Brocka's Area

C. Cerebellum

D. Cerebrum

E. Hippocampus

F. Occipital Lobe

G. Hippocampus

H. Hypothalamus

I. Inferior Colliculus.

J. Thalamus

K. Pons

L Superior Colliculus

M. Pineal Gland

N. Wernicke's Area

O. Pituitary Gland

1. "My heart tells me that you are the one. I love you so much!"

2. "IAOCEVOY! I don't know what that means. It's all Greek to me!"

3. "Chartreuse, Olive,Turquoise, and Mint are all shades of green."

4. "Janna always wakes up at 4 in the morning, regardless of whether she uses an alarm clock or not."

5. "I don't remember the way going to Myla's house. Can you accompany me there?"

6. Jenny's mother is about to give birth, she complains about contraction and pain usually when the baby is kicking

7. "Anthony is a very skilled dancer. He just won the school hip hop dance competition last week."

8. "As Nica was walking on the road she readily moved to the side for she heard an incoming ambulance"

9. "Elsa loves making faces whenever she talks to her friends."

10. "Ryan usually talks about how happy his high school days were to his grandchildren."

The change in enthalpy of an incompressible substance with a density of 1000 kg/m³ that is isothermally compressed from 100 to 1000 kPa is 0 kJ/kg.

Enthalpy is a measure of the total energy of a thermodynamic system. In addition, it incorporates the energy that is supplied to the system as heat, as well as any energy that is used as work. Enthalpy is represented by the symbol H and is usually calculated in units of joules (J).

An incompressible substance is one that cannot be compressed or compressed to a significant degree. Liquids are examples of such materials. They are often described as having a constant density because, unlike gases, they do not easily change in volume in response to pressure or temperature changes. Therefore, the change in enthalpy is 0 kJ/kg.

Learn more about Enthalpy here: https://brainly.com/question/16985375.

#SPJ11

Coordinate , A - the height of the stone when it hits the water. A slingshot sends a stone vertically upward from a height of 20 feet above a pool of water.

The coordinate A represents the height of the stone when it hits the water. When the stone hits the water, its height above the water surface is zero.

So, we can set the expression for the stone's height equal to zero and solve for t to find the time when the stone hits the water. The height of the stone when it is launched is given as 20 feet, which is a fixed value in this problem.

The time when the stone is launched is also a fixed value, which is zero. The maximum height of the stone is the highest point the stone reaches above its initial height of 20 feet. The time when the stone reaches its maximum height is the time at which the vertical velocity of the stone becomes zero.

To know more about vertical velocity , visit :

https://brainly.com/question/11679227

#SPJ1

The angular acceleration of the blades  is 5.897 rad/s². It can be calculated using the formula α as the ratio of torque to moment of Inertia.

The torque is a rotational or twisting force. Angular acceleration is the rate at which the angular velocity of an object changes, measured in radians per second squared (rad/s²).

Given the torque and moment of inertia, we may utilize the following formula to find the angular acceleration of the blades:

[tex]\alpha= \dfrac{Torque}{Moment \; of \; inertia}\\\alpha= \dfrac{\tau}{I}[/tex]

where τ is the torque in newton-meters (N-m),I is the moment of inertia in kg-m², α is the angular acceleration in radians per second squared (rad/s²).

Rearranging the formula to solve for α gives:

[tex]\alpha=2.3/0.39\\=5.897 rad/s^2[/tex]

Therefore, the angular acceleration of the blades is 5.897 rad/s².

For further information about angular acceleration click on below link:

https://brainly.com/question/30238727

#SPJ11

The proper subset relations that are possible using the sets of numbers n, z, q, and r are:

An improper subset comprises every element of the original set, while a valid subset only contains a fraction of the original set's numbers. A subset of a set A that is not equal to A is a proper subset of A. In other words, if B is a proper subset of A, then A has at least one element that is not in B but all of B's elements are in A.

Learn more about proper subset at brainly.com/question/17514113

#SPJ11

The correct option is B, the areas labeled X, Y, and Z represent constructive interference in which waves strengthen each other.

Interference is a phenomenon that occurs when two or more waves interact with each other. In physics, waves can be described as a disturbance that travels through a medium, such as water or air. When two waves meet, they can either reinforce or cancel each other out, depending on their amplitudes and phases.

Constructive interference occurs when the peaks of two waves coincide, creating a larger amplitude than either wave alone. Destructive interference occurs when the peak of one wave coincides with the trough of another, resulting in a cancellation of the waves. Interference is a fundamental concept in many areas of physics, including optics, acoustics, and electromagnetism.

To learn more about Interference visit here:

brainly.com/question/16098226

#SPJ4

Complete Question:

The diagram shows monochromatic light passing through two openings.

What do the areas labeled X, Y, and Z represent?

A). constructive interference in which waves cancel each other out

B). constructive interference in which waves strengthen each other

C). destructive interference in which waves cancel each other out

D). destructive interference in which waves strengthen each other

If the whole picture plane is affected by aerial diffusion, it stops being an effective indicator of depth - this statement is true.

Aerial diffusion is the scattering of light by particles in the air. These particles cause distant objects to appear fainter and bluer than closer objects, leading to a decrease in visual clarity and the ability to perceive depth. Aerial diffusion can be utilized in painting and drawing to create an atmospheric perspective, which produces a sense of depth by making objects are that further away appear hazier and less distinct than those that are closer. However, if the entire picture plane is affected by aerial diffusion, this can make it difficult to distinguish between objects at different depths, which can result in a lack of clarity and depth perception in the painting or drawing.

A picture plane is a theoretical plane that corresponds to the surface of a painting or drawing. The picture plane is where the artist organizes and arranges the various elements of the composition to create a visual representation of a scene. The picture plane is where the viewer's eye interacts with the artwork, and where the illusion of depth and space is created. In this context, the picture plane is an important factor in the creation of depth and atmosphere in a painting or drawing.

Learn more about aerial diffusion:

https://brainly.com/question/1381101

#SPJ11

The electric field inside the wire is still about 2.27 V/m, even though the electron mobility is 4 times higher. This is because the resistance of the wire remains the same, and Ohm's law still applies. The higher conductivity only means that a higher current flows through the wire for the same voltage, but the electric field remains the same.

We can use Ohm's law to find the electric field inside the Nichrome wire:

V = IR

where

V = 1.7 volts (battery voltage)

I = current

R = resistance of the wire

The resistance of a wire can be calculated using the formula:

R = (ρL) / A

where

ρ = resistivity of the material

L = length of the wire

A = cross-sectional area of the wire

The resistivity of Nichrome is about 1.10 x 10^-6 Ωm, and the cross-sectional area of the wire can be calculated using the formula for the area of a circle:

A = πr^2

where

r = radius of the wire = 0.125 mm = 0.000125 m

So, A = π(0.000125 m)^2 = 4.91 x 10^-8 m^2

Substituting the values, we get:

R = (1.10 x 10^-6 Ωm)(0.75 m) / (4.91 x 10^-8 m^2)

R ≈ 0.017 Ω

Now we can find the current:

I = V / R

I = 1.7 volts / 0.017 Ω

I ≈ 100 amps

The electric field inside the wire can be calculated using the formula:

E = V / L

where

E = electric field

V = potential difference

L = length of the wire

Substituting the values, we get:

E = 1.7 volts / 0.75 m

E ≈ 2.27 volts/meter or 2.27 V/m

So the electric field inside the Nichrome wire is about 2.27 V/m.

Next, we can repeat the calculations for the wire with the higher electron mobility. Since the mobile electron density and the length and diameter of the wire are the same, the resistance of the wire will also be the same as before. However, the higher electron mobility means that the wire will have a higher conductivity, which in turn means that the current will be higher for the same voltage.

Let's assume that the electron mobility is 4 times higher than that of Nichrome. Since the resistivity of the material remains the same, the conductivity will be 4 times higher as well. Therefore, the current will be 4 times higher than before:

I = 4 x 100 amps = 400 amps

Using the same formula as before, the electric field inside the wire can be calculated:

E = V / L

E = 1.7 volts / 0.75 m

E ≈ 2.27 volts/meter or 2.27 V/m

So, the electric field inside the wire is still about 2.27 V/m, even though the electron mobility is 4 times higher. This is because the resistance of the wire remains the same, and Ohm's law still applies. The higher conductivity only means that a higher current flows through the wire for the same voltage, but the electric field remains the same.

For such more questions on Ohm's law

https://brainly.com/question/14634041

#SPJ11

The masses listed on the periodic table are not whole numbers because they represent the weighted average of all the naturally occurring isotopes of an element.

Isotopes are atoms of the same element that have different numbers of neutrons in their nuclei, resulting in slightly different masses. Since the abundance of each isotope in nature can vary, the weighted average takes into account the abundance of each isotope and their corresponding masses, resulting in a decimal value. For example, oxygen has three naturally occurring isotopes, with mass numbers of 16, 17, and 18.

The most abundant isotope is oxygen-16, but the other isotopes are also present in trace amounts, leading to a weighted average of 15.9994 amu (atomic mass units). This is why the mass listed on the periodic table for oxygen is 15.999, which is a rounded value of the weighted average.

To know more about isotopes , visit :

https://brainly.com/question/11680817

#SPJ1

The masses listed on the periodic table are not whole numbers because they represent the average atomic mass of all the naturally occurring isotopes of an element, taking into account their relative abundances.

What are isotopes ?

Isotopes are atoms of the same element that have different numbers of neutrons in their nucleus, which affects their atomic mass. Some isotopes of an element are more abundant than others, and their relative abundances are taken into account when calculating the average atomic mass.

For example, oxygen has three naturally occurring isotopes: oxygen-16, oxygen-17, and oxygen-18. Oxygen-16 is the most abundant isotope, making up about 99% of all oxygen atoms. Oxygen-17 and oxygen-18 are much less abundant, but they still contribute to the overall atomic mass of the element.

The atomic mass listed on the periodic table for oxygen (15.9994) is the weighted average of the atomic masses of all three isotopes, taking into account their relative abundances. This average is not a whole number because the isotopes have different atomic masses and abundances, and their contributions to the overall average are weighted accordingly.

To know more about Periodic table visit :-

https://brainly.com/question/1173237

#SPJ1

The Kuiper belt is a disk-like region between the outer planets and the Oort cloud. Thus, option A is correct

The Kuiper belt, also known as the trans-Neptunian region, is a doughnut-shaped region of space beyond Neptune that is home to an estimated 100,000 tiny, icy objects.

It is named after Dutch-American astronomer Gerard Kuiper, who first proposed its existence in 1951.

The belt ranges in distance from 30 to 50 astronomical units (AU) from the Sun, which is about 2.8 to 4.7 billion miles away.

The Kuiper belt objects are believed to be remnants from the formation of the solar system. They are small and mostly made up of ice and dust, similar to comets.

Some Kuiper belt objects, such as Pluto and Eris, are classified as dwarf planets.

Learn more about the Kuiper belt here:

https://brainly.com/question/3955749

#SPJ11

True. A Faraday bag (also known as an electromagnetic bag) is a container made from metal or a special material that blocks any electromagnetic emanations from passing into or out of the bag, preventing a mobile device from communicating with the outside world.

This is because Faraday bags are electromagnetic bags that are designed to isolate electronic devices from external electromagnetic influence. They are also known as radiofrequency shielding bags, Faraday cage bags, signal blocker bags, or electromagnetic pulse (EMP) bags.

What are Faraday bags?

Faraday bags are made of a combination of metal or metal-coated fabrics that are designed to block electromagnetic signals from entering or leaving the bag. They are usually used to keep mobile devices such as smartphones and tablets from communicating with the outside world, especially in situations where an individual is worried about their privacy or security. They are also used by law enforcement agencies to prevent suspects from remotely wiping or deleting evidence on their devices.

How do Faraday bags work?

Faraday bags work by using a principle known as the Faraday effect, which states that any electric field in a conductor is shielded from the conductor's interior by the presence of an electric field. Faraday bags use this principle to block incoming and outgoing signals by creating an electrically conductive enclosure around the device. This means that when a mobile device is placed inside a Faraday bag, the bag acts as a Faraday cage, which shields the device from electromagnetic radiation. As a result, the device cannot communicate with the outside world.

For further details about Faraday bag, click on the below link:

https://brainly.com/question/23083952

#SPJ11

The average arterial pressure in your hands when they are held at your side is 47.5 mmHg.

The average arterial pressure in your hands when they are held at your side can be determined using the hydrostatic pressure formula, which is a function of height, gravity, and density. When the hands are held at the side, they are 60 cm below the heart, which means they are at a distance of 0.6 m.

The hydrostatic pressure formula is given by

P = ρgh

Where,

P is the pressure, ρ is the density, g is the acceleration due to gravity, and h is the height. We can assume that the density of blood is constant, and we can take the value of g to be 9.81 m/s², the standard acceleration due to gravity.

Therefore, the pressure at the heart is 100 mmHg, or 100/760 = 0.131 atm. The pressure in the hands can be calculated as follows:

P = ρghP = (1.06 × 10³ kg/m³) × (9.81 m/s²) × (0.6 m)

P = 6.26 × 10³ N/m²

P = 6.26 × 10³ Pa

P = 47.5 mmHg

Therefore, the average arterial pressure in the hands when they are held at the side is 47.5 mmHg.

Learn more about hydrostatic pressure at https://brainly.com/question/28206120

#SPJ11

None of the answer options provided are correct as they all involve calculations that assume certain values for the pressure, volume, and temperature of the gas.

What is Constant Pressure?

Constant pressure is a thermodynamic process in which the pressure of a system remains constant during the process. This means that any change in volume or temperature of the system must be accompanied by a corresponding change in some other property, such as the amount of heat added or removed from the system.

Since the gas is compressed at a constant pressure, the work done on the system can be calculated as:

W = -PΔV

In this case, P is constant, so we have:

W = -P(V2 - V1)

W = -P(4 m^3 - 10 m^3)

W = -P(-6 m^3)

W = 6P m^3

Since we are not given any information about the type of gas or its properties, we cannot use the ideal gas law to calculate the pressure P. Therefore, we cannot determine the exact value of the work done on the system.

Learn more about Constant Pressure from given link

https://brainly.com/question/2139620

#SPJ1

The total work done on a particle is given by the formula:

W = (1/2)mvf^2 - (1/2)mvi^2

where m is the mass of the particle, vi is the initial velocity, and vf is the final velocity.

For vi = 5 m/s and vf = 2 m/s, the final velocity is less than the initial velocity, so the total work is positive.

For vi = -2 m/s and vf = -5 m/s, the final velocity is less than the initial velocity, so the total work is positive.

For vi = -5 m/s and vf = 2 m/s, the final velocity is greater than the initial velocity, so the total work is negative.

For vi = 5 m/s and vf = -2 m/s, the final velocity is greater than the initial velocity, so the total work is negative.

For vi = -5 m/s and vf = -2 m/s, the final velocity is less than the initial velocity, so the total work is positive.

Therefore, the total work done on the particle is positive for vi = 5 m/s and vf = 2 m/s, and for vi = -2 m/s and vf = -5 m/s.

In order for work to be done, there must be a displacement of the object in the direction of the force applied. If the force and displacement are perpendicular, then no work is done.

Work can be positive, negative, or zero, depending on the direction of the force and the displacement. Positive work is done when the force and the displacement are in the same direction, negative work is done when they are in opposite directions, and zero work is done when there is no displacement or when the force and displacement are perpendicular.

Work is a transfer of energy, and as such it can change the kinetic energy, potential energy, or both of an object.

To know more about Work visit :

https://brainly.com/question/18094932

#SPJ1

The speed of sound is found out to be 349.4 ms⁻¹ from the frequency of the seventh resonance heard when the water level is 217.75 cm below the top of the tube.

Frequency of wave:

v = nλ

where, v = speed of sound, n = frequency, λ = wavelength

Speed of sound:

v = frequency n × wavelength λ

Frequency, n = v/λ

Wavelength, λ = v/n

The 7th resonance frequency of the tuning fork is given by:

n = 7 × f

where, f is the frequency of the tuning fork

Speed of sound, v = nλ

Speed of sound, v = 7fλ

Speed of sound, v = 7 × 256 Hz × λ

λ = 1.3671 m

Distance travelled by the sound wave in the water column is L = h + l

where, h = length of the air column and l = length of water column where the resonance was heard.

L = h + l

L = 217.75 cm + 50 cm

L = 267.75 cm = 2.6775 m

Length of the air column, h = L - l

where, l = length of water column where the resonance was heard.

h = 2.6775 m - 0.5 m

h = 2.1775 m

Wavelength of sound wave in air column, λ₁ = 4h

λ₁ = 4 × 2.1775 m

λ₁ = 8.71 m

Frequency of the sound wave in air column is given by:

n = v/λ₁

n = 349.4 ms⁻¹ / 8.71 m

n = 40.112 Hz

The 7th resonance frequency of the tuning fork is given by:

n = 7 × f

40.112 Hz = 7 × f

Frequency of the tuning fork, f = 5.73 Hz.

Learn more about Frequency here:

https://brainly.com/question/14316711

#SPJ11

Star A's light will take longer to reach us.

The energy needed to heat the water and the copper tank to 55°C is 25,083,080 J.

Q = mCΔT

m = 150 kg (mass of water)

C = 4.18 J/g°C (specific heat capacity of water)

ΔT = 55°C - 15°C = 40°C (change in temperature)

Using the formula, we get:

[tex]Q_{water}[/tex] = mCΔT

[tex]Q_{water}[/tex] = (150 kg) x (4.18 J/g°C) x (40°C)

[tex]Q_{water}[/tex] = 25,080,000 J

m = 20 kg (mass of tank)

C = 0.385 J/g°C (specific heat capacity of copper)

ΔT = 55°C - 15°C = 40°C (change in temperature)

Using the formula, we get:

[tex]Q_{tank}[/tex] = mCΔT

[tex]Q_{tank}[/tex] = (20 kg) x (0.385 J/g°C) x (40°C)

[tex]Q_{tank}[/tex]= 3080 J

Finally, we can add the two energies together to get the total energy needed:

[tex]Q_{total}[/tex] = [tex]Q_{water}[/tex] [tex]+[/tex] [tex]Q_{tank}[/tex]

[tex]Q_{total}[/tex] [tex]= 25,080,000 J + 3080 J[/tex]

[tex]Q_{total}[/tex] [tex]= 25,083,080 J[/tex]

Energy is a fundamental concept that refers to the ability of a physical system to do work or cause a change. It is a scalar quantity that is measured in units of joules (J) in the International System of Units (SI). According to the law of conservation of energy, energy cannot be created or destroyed, but it can be transformed from one form to another. This means that the total amount of energy in a closed system remains constant.

Energy is a crucial concept in many areas of physics, including mechanics, thermodynamics, and electromagnetism. Understanding energy is essential for understanding how the physical world works, and it has numerous applications in technology and everyday life, from powering our homes and vehicles to the production of food and the functioning of our bodies.

To learn more about Energy visit here:

brainly.com/question/2409175

#SPJ4

The correct answer is option D.2 years

According to Kepler's Third Law of Planetary Motion, T² is proportional to r³, where T is the period of revolution of the planet and r is the distance between the planet and the star.

In order to solve for T,  

AU = 1

Astronomical Unit = the average distance between the Earth and the Sun = 149.6 million kilometres

Therefore, the planet is orbiting at a distance of 149.6 million kilometres from the star.

Substituting the values of r and solving for

T².T² ∝ r³T² ∝ (149.6)³T²

= (149.6)³T²

= 3.522 x 10¹²T

= √3.522 x 10^¹²T

= 1.87 x 10⁶ seconds

T = 31,100 minutes

T = 518 hours

T = 21.6 days

T = 2 years

Therefore, the orbital period of the planet with twice the mass of Earth orbiting at a distance of 1 AU from a star with the same mass as the Sun is 2 years.

To know more about Kepler's third law of planetary motion:

https://brainly.com/question/4978861

#SPJ11

The most appropriate option among the given options is C. A white dwarf is what most stars become when they die.What is a white dwarf?A white dwarf is a small, compact object that is the final stage of stellar evolution for most stars in the universe.

The star exhausts its fuel and begins to cool after it has used up all of the hydrogen fuel that powers its nuclear reactions. This phase of a star's evolution is referred to as a red giant. The star then sheds its outer layers of gas, exposing its core. The hot, glowing core of a star is exposed as a white dwarf once the outer layers have been ejected.What most stars become when they die is a white dwarf. This is one of the most fascinating phenomena in the universe, as well as one of the most intriguing. Furthermore, a white dwarf is a dense, compact object that is frequently composed of carbon and oxygen. It has no more nuclear fuel to burn, therefore it does not produce energy. As a result, it gradually fades away into the blackness of space, eventually turning into a black dwarf. However, it is believed that no black dwarfs have been observed yet.White dwarfs are not precursors to black holes or neutron stars, as those objects are formed from more massive stars that undergo different processes at the end of their lives. Brown dwarfs are also different objects, being failed stars that never achieved the temperature and pressure necessary for sustained nuclear fusion.

For more such questions one white dwarf

https://brainly.com/question/13914155

#SPJ11

. Additionally, Star 1 has prominent hydrogen lines, indicating a lower temperature than Star 2. Therefore, the statements can be sorted into the true and false bins as indicated above.

True: Star 1 has a longer lifetime than Star 2; Star 2 is bluer than Star 1; Star 2 has a lower mass than Star 1; Star 1 has prominent hydrogen lines.

False: Star 2 has a higher luminosity than Star 1; Star 2 is cooler than Star 1.

The spectra of the two main sequence stars illustrate some differences between the two stars. Star 1 is on the left and has a longer lifetime than Star 2, which is on the right. This is evident from the intensity axes that are not on the same scale. Star 2 has a lower mass than Star 1, is bluer than Star 1, and has a lower luminosity

for such more questions on hydrogen lines

https://brainly.com/question/30461609

#SPJ11