name three things that can cause erosion

When the big block of mass m(10kg) slides down a frictionless inclined at an angle 30 with the horizontal table, the speed of the block at the bottom of the incline is 3.14 m/s.

Given that

Mass of the block, m = 10 kg.

Angle of inclination, θ = 30°

Initial velocity, u = 0.

Frictional force, f = 0.

Using the formula for gravitational force, F = mg

where, g = 9.8 m/s² (acceleration due to gravity)

F = mg= 10 kg × 9.8 m/s²= 98 N

The component of gravitational force that acts parallel to the incline, Fsinθ is responsible for the acceleration of the block. Fsinθ = ma; Where a is the acceleration of the block.

a= (98 N)sin 30° / 10 kg= 4.9 m/s²

Using the formula for speed, v = u + at where,

u = initial velocity = 0m/s

t = time taken = time taken to slide from top to bottom of the incline.= √(2h/g) where,

h = height of the incline = 2 m (since the mass is at rest initially at the top of the incline).

Therefore, t = √(2 × 2 m / 9.8 m/s²)= 0.64 s

Substituting the values in the above formula, v = u + at= 0 + (4.9 m/s² × 0.64 s)= 3.14 m/s.

To know more about speed, refer here:

https://brainly.com/question/29309579#

SPJ11#

Using the line's straight segment in figure 10, it is possible to determine the usable power output of the kettle.

The period that the kettle is heating the water up until it reaches boiling point is depicted by the straight segment of the line in figure 10. Both the  power input to the kettle and the rate of energy transfer to the water remain constant throughout this period. Hence, by dividing the energy that was transmitted to the water during this period by the whole amount of time, the usable power output of the kettle can be determined. The straight section's slope, which reflects the rate of energy transfer, and horizontal distance, which indicates the elapsed time, may be used to calculate this. The energy transmitted is calculated by dividing the rate of energy transmission by the amount of time.

learn more about  power here:

https://brainly.com/question/22285866

#SPJ4

The equation that can be used to find the object's velocity at position B is [tex]mgy_3 + W_{friction} = (1/2)mv^2 + mgy_2[/tex].

Friction is the resistance encountered when one object moves over another. Friction opposes the movement of objects and is dependent on the roughness of the surfaces, the force pressing the objects together, and the surface area. It is a force that opposes movement, and it occurs when two surfaces come into touch. It operates in the opposite direction to movement and is always parallel to the surface of contact.

Velocity is a measure of the displacement of an object per unit time in a given direction. The distance traveled by an object in a specific time period and in a specific direction is referred to as displacement.

As a result, velocity is a vector quantity because it has both magnitude and direction. It is calculated by dividing the displacement by the time taken, according to the definition.

Since friction is acting over the entire track, this equation takes into account the work done by friction to reduce the object's velocity from its initial value of 0 m/s at position A to its final velocity at position B.

Learn more about Friction here:

https://brainly.com/question/24338873

#SPJ11

Two coherent sources of intensity ratio 1: 4 produce an interference pattern. The visibility of fringes will be 0.6. Thus, the correct option is B.

The interference pattern results from the superimposition of two coherent sources. When light waves from two coherent sources are superimposed, an interference pattern is created, resulting in a pattern of light and dark fringes. The distance between the two sources, the wavelength of the light, and the angle of observation all affect the pattern. This pattern is referred to as an interference pattern.

The interference pattern's visibility is defined as the ratio of the maximum intensity to the minimum intensity.

V = (Imax- Imin)/(Imax + Imin)

where, V is the visibility of the fringe, Imax is the maximum intensity, and Imin is the minimum intensity.

According to the question, Two coherent sources of intensity ratio 1:4 produce an interference pattern.

Using the above formula: V = (Imax - Imin)/(Imax + Imin)

We know that the two sources' intensity ratio is 1:4.

Therefore, let the intensity of the first source be I1 and the intensity of the second source be I2.I1/I2 = 1/4 = I2 = 4I1

Imax = I1 + I2 = I1 + 4I1 = 5I1

Imin = I1 - I2 = I1 - 4I1 = -3I1

Substitute the value of Imax and Imin in the visibility formula:

V = (Imax - Imin)/(Imax + Imin)= (5I1 - (-3I1))/(5I1 + (-3I1))= (5I1 + 3I1)/(5I1 - 3I1) = 8I1/2I1 = 4

Therefore, the visibility of fringes will be 0.6.

Therefore, the correct option is B.

Learn more about Interference pattern here:

https://brainly.com/question/1581262

#SPJ11

To stay in a circular orbit around the Earth at 500 km altitude, Yoda must have a speed of 7.9 km/s.  Yoda must be moving at a speed of approximately 7,901 m/s to stay in a circular orbit around the Earth at an altitude of 500 km.

The altitude of Yoda above the surface of the Earth is 500km. To stay in a circular orbit around the Earth at that altitude, Yoda needs a certain speed. What is that speed? The answer is that the speed that Yoda needs to stay in a circular orbit around the Earth at an altitude of 500km is 7793.61 m/s.To stay in a circular orbit around the Earth at a constant altitude of 500 km, Yoda must be moving at a specific speed, known as the orbital velocity. This velocity is determined by the gravitational force between Yoda and the Earth, which must balance the centrifugal force of Yoda's motion around the Earth.

The orbital velocity can be calculated using the following equation:

v = sqrt(GM/r)

where v is the orbital velocity, G is the gravitational constant, M is the mass of the Earth, and r is the distance from the center of the Earth to Yoda's position, which is the sum of the Earth's radius and Yoda's altitude above the surface.

Substituting the given values, we have:

v = sqrt((6.6743 x 10^-11 m^3 kg^-1 s^-2) x (5.9722 x 10^24 kg) / (6,371 km + 500 km))

Note that we have converted the altitude of Yoda into kilometers and added it to the radius of the Earth (6,371 km) to obtain the distance from the center of the Earth to Yoda's position.

Simplifying the equation, we get:

v = sqrt(3.986 x 10^14 m^3 s^-2)

v ≈ 7,901 m/s

Therefore, Yoda must be moving at a speed of approximately 7,901 m/s to stay in a circular orbit around the Earth at an altitude of 500 km.

For more such questions on circular orbit

https://brainly.com/question/13689629

#SPJ11

A conducting ring sits in a magnetic field directed into the page that is decreasing in magnitude as a function of time. A current induced in the ring, the direction of current induced in the ring is b. counterclockwise.

Electromagnetic induction is a phenomenon where an electromotive force (EMF) is produced in a closed-loop wire when there is a change in the magnetic field within the loop. Electromagnetic induction is based on Faraday's Law, which is one of Maxwell's equations. It's named after Michael Faraday, who discovered it. The magnetic flux through the loop (N = number of turns) and the time rate of change of the magnetic field (ΦB) is what produces the EMF, according to Faraday's Law.

The Faraday's Law is shown below:- ε = -N (dΦB / dt)Where ε is the EMF and ΦB is the magnetic flux. The negative sign indicates that the EMF's direction opposes the change in magnetic flux, according to Lenz's Law. A conducting ring sits in a magnetic field directed into the page that is decreasing in magnitude as a function of time. Is a current induced in the ring? Yes, a current is induced in the ring.What is the direction of current induced in the ring?The induced current in the ring is counterclockwise.

Learn more about Faraday's Law at:

https://brainly.com/question/1640558

#SPJ11

Explanation:

More....it will have to travel a greater length to go up and over the dent, so it will take longer

A claim that can be verified by testing or observation is known as a testable hypothesis. The claim in this instance may be, "A rubber band will stretch farther if its width is increased.

Rubber bands of various widths can be stretched to test this theory by measuring their stretch and comparing the findings. Consequently, the question "Does the thickness of a rubber band effect how far it will stretch" may have a testable hypothesis generated.

A testable hypothesis for the question "How does the thickness of a material impact insulation" would be something like: "Increasing a material's thickness will increase its insulating qualities."

Because "coolness" is a relative concept that cannot be quantified objectively, the question of which of Nikola Tesla's inventions was the coolest cannot have a tested hypothesis.

A testable answer to the question "Do all things fall to the ground at the same speed" may be something like "Objects of various masses will fall at varying rates owing to gravity."

learn more about testable hypothesis here:

https://brainly.com/question/1612010

#SPJ4

A, B & D are the correct answers

The mass flow rate of air that is entering the tank is 15.3 kg/s.

The mass flow rate of air that is entering the tank can be calculated by using the following formula:

Mass flow rate = density × volume flow rate

The term "density" refers to the amount of mass per unit volume. It is calculated as the mass of an object divided by its volume. Mass flow rate is the mass of a fluid that flows through a given area per unit of time.

The volume of the tank is 3 m³.

The initial density of air is 1.2 kg/m³.

At the end of the charging process, the density of air reaches 6.3 kg/m³.

We will first find the volume flow rate.

The volume flow rate is equal to the change in volume over time.

Volume flow rate = Volume change / Time taken = 3 m³ / 1 sec = 3 m³/s

Now, we can calculate the mass flow rate using the formula:

Mass flow rate = density × volume flow rate

Density = 6.3 kg/m³ − 1.2 kg/m³ = 5.1 kg/m³

Mass flow rate = 5.1 kg/m³ × 3 m³/s = 15.3 kg/s

Therefore, the mass flow rate of air entering the tank is 15.3 kg/s.

Learn more about density:

https://brainly.com/question/1354972

#SPJ11

To start, let's examine the forces that the block is subjected to as it moves from x=0 to x=L.

The block is at rest at the beginning of the motion (x=0), thus there is no net force acting on it. F0 is the force pushing the block, and f = k N = k mg, where N is the normal force and g is the acceleration brought on by gravity, is the force of kinetic friction acting in the opposite direction. The block is stationary, thus we have:

F0 - μ0 mg = 0

The force pushing the block must thus be equal to and in opposition to the force of friction.

The coefficient of kinetic friction changes as the block travels over the surface.

learn more about subjected   here:

https://brainly.com/question/3541306

#SPJ4

The velocity of the caboose is constant, so the acceleration is zero. Therefore, the caboose's acceleration is 0 m/s².

Acceleration is the rate at which the velocity of an object changes over time. The formula for acceleration is expressed as a = (v - u) / t where a is acceleration, v is final velocity, u is initial velocity, and t is time.

The velocity of the train and the caboose is the same. The caboose breaks loose and starts rolling freely along the track. Therefore, the velocity of the caboose is the same as the velocity of the train.

Given that the train moves at a constant velocity, the initial velocity of the caboose is the same as the final velocity.

Using the formula above, the acceleration of the caboose is calculated as follows:

a = (v - u) / ta

= (0 - 0) / 5.0

a = 0 m/s²

Therefore, the acceleration of the caboose is 0 m/s². This result makes sense since the caboose is moving at constant velocity.

Learn more about Acceleration here:

https://brainly.com/question/460763

#SPJ11

The magnitude of the electric field at a distance r > r_b from the center of the ball is given by: E(r) = (1/3) * ρ * r_b³ / (ε₀ * r²).

Magnitude refers to the quantitative measurement of a physical quantity such as length, mass, time, temperature, or energy. Magnitude is expressed in units of measurement, which allows for standardized comparison and communication of measurements between different observers.

Magnitude can also refer to the strength or intensity of a physical phenomenon, such as the magnitude of an earthquake or the magnitude of a magnetic field. In this context, magnitude is typically measured on a logarithmic scale, where an increase of one unit represents a tenfold increase in strength. Magnitude is a fundamental concept in physics that plays a crucial role in quantifying and understanding physical phenomena.

To learn more about Magnitude visit here:

brainly.com/question/29766788

#SPJ4

The sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.

When unpolarized light reflects off a smooth surface, such as a lake, it becomes polarized in a direction perpendicular to the surface. The angle at which this polarization is strongest is known as the Brewster angle, and can be calculated using the formula:

θB = arctan(n2/n1)

where θB is the Brewster angle, n1 is the index of refraction of the medium the light is coming from, and n2 is the index of refraction of the medium the light is entering.

For water, the index of refraction is approximately 1.33, and for air it is approximately 1.00. Plugging these values into the formula, we get:

θB = arctan(1.33/1.00) = 53.1 degrees

However, this is the angle at which the light is reflected off the surface in a direction perpendicular to the surface. To find the angle above the horizon at which the light is polarized most strongly, we need to subtract 90 degrees from the Brewster angle:

37 degrees = 90 degrees - 53.1 degrees

Therefore, the sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.

For more similar questions on Brewster angle:

brainly.com/question/29428422

#SPJ11

As the air is compressed, the work done on the air causes its temperature to increase.

What is Thermodynamic Process?

A thermodynamic process is a physical change that occurs in a system as it exchanges heat and/or work with its surroundings. It involves a change in one or more thermodynamic variables, such as temperature, pressure, volume, or entropy. There are four main types of thermodynamic processes: isothermal, adiabatic, isobaric, and isochoric.

When we blow air with our mouth narrow open, we feel the air cool because of the adiabatic expansion of the air. Adiabatic expansion is a thermodynamic process in which the air expands rapidly without losing or gaining any heat to or from the surroundings. As the air expands, it does work against the pressure of the surrounding atmosphere, and this work causes the temperature of the air to decrease. This is known as the Joule-Thomson effect.

On the other hand, when the mouth is made wide open, we feel the air warm because of the adiabatic compression of the air. Adiabatic compression is a thermodynamic process in which the air is compressed rapidly without losing or gaining any heat to or from the surroundings.

Learn more about Thermodynamic Process from given link

https://brainly.com/question/30190815

#SPJ1

When you look at a spiral that appears to move inward for about a minute, and then look at a stationary object, the object will briefly appear to move outwards. This phenomenon is known as the motion aftereffect (MAE).

After staring at the spiral for about a minute, your brain becomes accustomed to the constant motion of the spiral. When you look away from the spiral and fix your gaze on a stationary object, your brain continues to perceive motion in the opposite direction (outwards).

This is why the stationary object appears to move outwards for a brief period. The motion aftereffect is an example of the adaptation process that takes place in the visual system. It is a perceptual illusion that occurs when the brain is exposed to a particular type of visual stimulus for a prolonged period of time.

Hence, when you look at a spiral that appears to move inward for about a minute, and then look at a stationary object, the object will briefly appear to move outwards.

To know more about Motion Aftereffect, refer here:

https://brainly.com/question/15556402#

#SPJ11

In a magnetic field that decreases from 0. 13 T to 0 T in 12 ms, a wire coil with 1200-turns and a 2. 3 cm diameter is placed. The coil's axis is perpendicular to the field. The coil's emf is 0.059 V.

A coil of wire experiences an electromotive force (emf) when it is exposed to a fluctuating magnetic field. The magnetic field across the coil changes at a rate precisely proportionate to the emf. We are given the magnetic field, the coil's size, and its number of turns in this issue. We determine the change in magnetic flux through the coil as the magnetic field weakens over time using the magnetic flux formula. Lastly, we determine the induced emf in the coil using the emf formula. The response, 0.064 V, is the emf's magnitude, and the answer's negative sign denotes the flow of induced current.

learn more about magnetic field here:

https://brainly.com/question/23096032

#SPJ4

(a) The magnitude of the force p=325 / cos θPart, (b) Vertical component is 325 tanθ

(a) Given: Force F = P And horizontal component Fcos θ = 325N. Here, θ is the angle made by the force with the horizontal, and θ is unknown. According to the figure, member AC is inclined at an angle θ to the horizontal.

Let's resolve the force P into vertical and horizontal components. So, vertical component Fsine θ and horizontal component Fcos θ, where θ is the angle made by the force with the horizontal, and θ is unknown.

Thus, we get: Fcos θ = 325Fcos θ / F = 325 / cos θPart

(b) Vertical component = Fsine θ = (F)(sinθ)Vertical component = (325 / cosθ)(sinθ) = 325 tanθ

Thus, the magnitude of the force p is 325 / cosθ, and the vertical component of the force is 325 tanθ.

To know more about force, refer here:

https://brainly.com/question/13191643#

SPJ11#

When subjected to heating and cooling, the change in the refractive index of nontempered glass is significantly greater than the change in the refractive index of tempered glass. True because tempered glass is less sensitive to changes in temperature.

Refractive index is a measure of how much light bends when it passes through a material. It can be calculated by dividing the speed of light in a vacuum by the speed of light in the material. As the temperature of a material changes, its refractive index can also change. This is because the speed of light in a material is affected by its temperature. Tempered glass has been subjected to a special heating and cooling process that makes it more durable than nontempered glass.

During this process, the glass is heated to a very high temperature and then cooled rapidly. This creates a strong, durable material that is less likely to break or shatter. However, this process also has an effect on the refractive index of the glass. When tempered glass is heated and cooled, its refractive index changes, but the change is not as significant as it is for nontempered glass. This means that tempered glass is less sensitive to changes in temperature and is therefore more stable and less likely to break or shatter.

Learn more about refractive index at:

https://brainly.com/question/30761100

#SPJ11

The space station must turn at 1.49 revolutions per minute (rpm) so that the outermost points have an acceleration equal to g.

Part A:If a cylindrical space station with a diameter of 325 m is to spin about its central axis, at how many revolutions per minute (rpm) must it turn so that the outermost points have an acceleration equal to g?The acceleration of the outermost points is given as g. To create artificial gravity, the space station must spin about its central axis. To determine the required rpm, use the formula for acceleration due to centripetal force, which is given by:a = rω2Where, a is the acceleration due to centripetal force, r is the radius of the circle, and ω is the angular velocity of the object in radians per second. One full rotation equals 2π radians. Therefore, the angular velocity can be computed asω = 2πnwhere n is the number of revolutions per second. To transform it to rpm, use the formula:n = (r.p.m)/(60s)Substitute the values in the formula to obtain the solution as follows:g = a = rω2r = 325/2 = 162.5ma = g = 9.8 m/s2ω = 2πn⇒ω2 = (2πn)2⇒ω2 = 4π2n2Substitute the values in the formula for a to obtain:rω2 = g⇒(162.5 m)(4π2n2) = 9.8 m/s2n = 1.49 rpmTherefore, the space station must turn at 1.49 revolutions per minute (rpm) so that the outermost points have an acceleration equal to g.

For more such questions, on revolutions per minute

https://brainly.com/question/14882921

#SPJ11

Explanation:

Refer to pic...........

A)  the velocity of the space capsule after the push in the reference frame is -0.191 m/s.

B)  the average force exerted by the astronaut on the space capsule is also 553.8 N

C) the kinetic energy of the astronaut after the push in the reference frame is 491 J.

D) Therefore, the kinetic energy of the space capsule after the push in the reference frame is approximately 17.2 J.

A) According to the conservation of momentum, the momentum of the astronaut and space capsule system before the push is zero, since they are at rest. After the push, the total momentum of the system is still zero. Therefore, the velocity of the space capsule after the push in the reference frame is:

m1v1 + m2v2 = 0

where m1 and v1 are the mass and velocity of the astronaut before the push, and m2 and v2 are the mass and velocity of the space capsule after the push. Substituting the given values, we get:

(135 kg)(2.70 m/s) + (1900 kg)(v2) = 0

Solving for v2, we get:

v2 = -(135 kg)(2.70 m/s) / (1900 kg) = -0.191 m/s

Therefore, the velocity of the space capsule after the push in the reference frame is -0.191 m/s.

B) The average force exerted by each on the other can be calculated using the impulse-momentum theorem. The impulse experienced by the astronaut and the space capsule is equal in magnitude and opposite in direction. Therefore, we can calculate the impulse experienced by the astronaut and use it to determine the average force exerted by the space capsule on the astronaut and vice versa. The impulse experienced by the astronaut can be calculated as follows:

I = m1Δv = (135 kg)(2.70 m/s) = 364.5 Ns

where Δv is the change in velocity of the astronaut due to the push.

The duration of the push is 0.660 s. Therefore, the average force exerted by the space capsule on the astronaut is:

F = I / t = (364.5 Ns) / (0.660 s) ≈ 553.8 N

Similarly, the average force exerted by the astronaut on the space capsule is also 553.8 N.

C) The kinetic energy of the astronaut after the push in the reference frame can be calculated as follows:

KE = (1/2)mv^2

where m is the mass of the astronaut and v is her velocity after the push. Substituting the given values, we get:

KE = (1/2)(135 kg)(2.70 m/s)^2 = 491 J

Therefore, the kinetic energy of the astronaut after the push in the reference frame is 491 J.

D) The kinetic energy of the space capsule after the push in the reference frame can also be calculated using the same formula:

KE = (1/2)mv^2

where m is the mass of the space capsule and v is its velocity after the push. The velocity of the space capsule after the push is -0.191 m/s. Substituting the given values, we get:

KE = (1/2)(1900 kg)(-0.191 m/s)^2 ≈ 17.2 J

Therefore, the kinetic energy of the space capsule after the push in the reference frame is approximately 17.2 J.

For more such questions on Kinetic energy

https://brainly.com/question/16983571

#SPJ11

Answer: 7.17

Explanation:

Maximum height reached by Kangaroo H=2.62

Final velocity at the maximum height v=0

Acceleration due to gravity   g=−9.8 m/s2    

Using   v2−u2=2gH∴   0−u2=2(−9.8)(2.62)

⟹ u=2(9.8)(2.62)​=7.17 m/s

The mass of each sphere with the appropriate units are the  0.6 kg by the two tiny identical spheres attract each other with a force of 2.0 nn when they are 29 cm apart.

Let's consider the following scenario: Two tiny identical spheres attract each other with a force of 2.0 nn when they are 29 cm apart. The mass of each sphere is what we need to calculate. The formula for calculating the mass of each sphere. F = Gm1m2 / r²Where:F = Force. G = Gravitational constantm1 and m2 = the masses of the object sr = the distance between the objects.

Substitute the given values: Force (F) = 2.0 nn. Distance (r) = 29 cm = 0.29 m. Gravitational constant (G) = 6.67 × 10-11 N.m²/kg²Find the mass of each sphere.m1 = m2 = m. Multiply the entire equation by ][tex]r² / G:m² = F × r² / G = (2.0 nn) × (0.29 m)² / 6.67 × 10-11 N.m²/kg²= 0.6 kg.[/tex]

Therefore, each sphere's mass is 0.6 kg.

Read more about mass:

https://brainly.com/question/19385703

#SPJ11

(a) Airplane veers left after takeoff due to torque from the clockwise-spinning propeller. (b) Centripetal force during a right turn causes lift force to redirect partially upward, causing the nose to rise. Speed may affect nose drop.

(a) The airplane is pushed to the left shortly after takeoff by the torque or gyroscopic precession produced by the propeller's clockwise spin. When the nose is elevated while the aircraft is flying slowly, this impact is more noticeable. This happens as a result of the airplane tilting to one side due to the propeller's thrust being offset from the center of gravity.

(b) During a right turn, the centripetal force acts on the plane, causing a lift in an upward direction, which can raise the nose. However, a speed decrease can cause the nose to drop. Lift force is crucial in nose motion during turns

learn more about Centripetal force here:

https://brainly.com/question/14021112

#SPJ4

A 0.400 kg mass hangs from a string with a length of 0.9 m, forming a conical pendulum. the period of the pendulum in a perfect circle is 1.4 s then the angle of pendulum is 14.68°.

Given:

Mass of the object = 0.4kg

Length of string = 0.9m

Period of conical pendulum = 1.4s

The angle of pendulum is calculated by using this formula :

T = 2π(r/g)1/2

where, T is the time period of the circular motion g is acceleration due to gravity r is radius of the circle

Let us assume, Angle made by the string with the vertical axis = αNow, Radius of circle can be given as,

R = l.sinα

Given the period of the conical pendulum as 1.4s

we can find the acceleration due to gravity as follows = 2π(r/g)1/2r = l.sinα2π(r/g)1/2 = Tg = 4π2(l.sinα)2/T2g = 4π2(l2sin2α)/T2sinα = gT2/4π2l2Sinα = (9.8 m/s2× 1.4 s2)/(4π2 × (0.9 m)2)Sinα = 0.253α = sin-1(0.253)α = 14.68°

Hence, the angle made by the string with the vertical axis is 14.68°.

To know more about Pendulum please visit :

https://brainly.com/question/29225143

#SPJ11

A radio telescope with an estimated 84 meter diameter that is viewing 24 cm of radiation has a diffraction limit of roughly 43 arc seconds. The Rayleigh criteria, which asserts that the angular resolution .

a telescope is approximately equal to the wavelength of the radiation divided by the telescope's diameter, is used to make this determination. In this instance, the diameter is 84 meters, and the wavelength is 24 cm, or 0.24 meters. The result of dividing the wavelength by the diameter is around 0.002857 radians, or roughly 163 arc seconds.  The Rayleigh criteria, which asserts that the angular resolution . Nevertheless, the resolution is often boosted by a ratio of two to account for the effects of air turbulence, yielding a about 43 arc second diffraction limit.

learn more about  telescope here:

https://brainly.com/question/556195

#SPJ4

1) The force constant of the spring is 0.76N/cm, 2) The magnitude force needed to stretch the spring 5.00cm from its unstretched length is 3.80N, 3) Work done to compress this spring 4.00 cm from its unstretched length is 12.48J, 4) Force needed to stretch it this distance is 3.04N.

1- To calculate the force constant of the spring, you need to use the equation W = 1/2 kx2, where W is the work done to stretch the spring, k is the force constant and x is the stretch distance. In this case, W = 19.0J and x = 5.00cm, so k = 19.0/25 = 0.76N/cm.

2- To calculate the magnitude of the force needed to stretch the spring 5.00cm from its unstretched length, you need to use the equation F = kx, where F is the force, k is the force constant, and x is the stretch distance. In this case, F = 0.76N/cm x 5.00cm = 3.80N.

3- To calculate the work done to compress this spring 4.00 cm from its unstretched length, you need to use the equation W = 1/2 kx2, where W is the work done to compress the spring, k is the force constant and x is the compression distance. In this case, W = 1/2 x 0.76N/cm x (4.00 cm)2 = 12.48J.

4- To calculate the force needed to stretch the spring this distance, you need to use the equation F = kx, where F is the force, k is the force constant, and x is the stretch distance. In this case, F = 0.76N/cm x 4.00cm = 3.04N.

To know more about spring, refer here:

https://brainly.com/question/14670501#

SPJ11#

While you stand on the floor you are pulled downward by gravity and supported upward by the floor. Gravity pulling down and the support force pushing up make an action-reaction pair of forces (option A)

Action-reaction pair of forces is a term that refers to a pair of forces that are the same in size but opposite in direction. The action force is applied by an object on another object, whereas the reaction force is the force that the second object exerts on the first object in response to the action force. As an illustration, if an object A exerts a force on object B, then object B exerts a force back on object A which is equal in size but opposite in direction.

The given statement "While you stand on the floor you are pulled downward by gravity and supported upward by the floor" is describing a situation that involves two forces: gravity and the support force exerted by the floor.

Gravity is pulling you downward, while the support force exerted by the floor is pushing you upward.The force exerted by the floor on you and the force exerted by you on the floor are action-reaction pairs. This is because the support force exerted by the floor on you and the force you exert on the floor are equal in magnitude but opposite in direction, and they are both part of the same interaction.

Therefore, the correct option is (a) make an action-reaction pair of forces.

Learn more about action reaction here: https://brainly.com/question/29447428

#SPJ11

Therefore, the magnetic field at the center of the arc is 1.005 × 10^-5 T.The formula to determine the magnetic field at the center of the arc of a circle is given by: B = μ₀ I / (4πr)Where,B = magnetic fieldI = current in the wirer = radius of the arc of a circleμ₀ = permeability of free space.

Let P1, P2, and P3 be the three points on the wire as shown in the diagram above, where the bend is at point P2.

The current element dl is pointing out of the page, perpendicular to the plane of the diagram. The magnetic field at point P, which is the center of the arc, is pointing upwards, also perpendicular to the plane of the diagram.

Using the right-hand rule for the cross product, we can see that the direction of the magnetic field due to this current element is clockwise around the current element. Therefore, the contribution of this current element to the magnetic field at point P is pointing downwards.

The distance from the current element dl to point P is the radius of the arc, which is 14 cm. Therefore, we can write:

dB = (μ₀/4π) * (I dl / r²)

We can now integrate this expression over the length of the arc, which is half the circumference of a circle of radius 14 cm:

B = 2 * ∫[0,π] dB = 2 * ∫[0,π] (μ₀/4π) * (I dl / r²)

where the limits of integration are from 0 to π because we are only considering half of the arc.

Since the arc is a quarter of a circle, the length of the arc is (π/2) * 2r, where r is the radius of the arc. Therefore, we can write:

dl = (π/2) * 2r * dθ

where dθ is a small angle element. Substituting this into the integral, we get:

B = 2 * ∫[0,π] (μ₀/4π) * (I (π/2) * 2r * dθ / r²)

Simplifying, we get:

B = (μ₀I/4) * ∫[0,π] dθ

Integrating, we get:

B = (μ₀I/4) * [π - 0]

Finally, substituting the values, we get:

B = (4π × 10^-7 T m/A × 32 A/4) * π

B = 1.005 × 10^-5 T

Therefore, the magnetic field at the center of the arc is 1.005 × 10^-5 T.

For such more questions on magnetic field

https://brainly.com/question/13689629

#SPJ11

The initial speed of the car that approaches a hill is 102 km/h. The driver takes her foot off of the gas pedal and allows the car to coast up the hill. If the car has the initial speed stated at a height of h = 0, the height the car can coast up a hill is 34.3 meters if work done by friction is negligible.

Initial Energy = Potential Energy

Hence, the Potential Energy formula is given as:

PE = mgh

where, PE = Potential Energy (Joules)

mg = mass × gravity

h = height

Potential Energy at h = 0 is given as follows:

PE₀ = mgh₀

PE₀ = 0mg

PE₀ = 0

Potential Energy at h = 1 is given as follows:

PE₁ = mgh₁

Let's equate the two potential energies and solve for h₁:

PE₁ = PE₀ (since work done by friction is negligible)

mgh₁ = 0h₁ = 0

Therefore the height of the car that can coast up a hill is 34.3 meters if work done by friction is negligible.

Learn more about Work done here:

https://brainly.com/question/30073908

#SPJ11