The energy stored in the capacitor is calculated as 630150 J. The ratio between the energy density per unit mass of the 9.0 kg capacitor system and the 130,000 J/kg of the truck's battery is 70.17
The formula to calculate the energy stored in a capacitor is expressed by the formula:
E = (1/2)CV²
where E is energy, C is capacitance, and V is voltage.
The question mentions that the capacitor is fully charged to 13.8 V. Therefore, the energy stored in the capacitor is given by the formula:
[tex]E = (1/2)CV^2 \\= (1/2)\times (500 F)\times {(13.8 V)}^2\\= 630150 J[/tex]
The ratio between the energy density per unit mass of the 9.0 kg capacitor system and the 130,000 J/kg of the truck's battery can be computed by dividing the energy density of the capacitor system by the energy density of the truck's battery.
We know that energy density = energy / mass of the system.
Thus, the formula to calculate the ratio is:
[tex]Ratio = \dfrac{energy density per unit mass of capacitor system}{ energy density per unit mass of truck's battery}\\Ratio= \dfrac{630150 J / 9 kg}{ 130,000 J / 1 kg}= 70.017[/tex]
Therefore, the ratio of energy density per unit mass of the capacitor system to that of the truck's battery is 70.017.
To know more about capacitor, kindly click the below link:
https://brainly.com/question/29100869
#SPJ11
all but which condition must be present for the calvin cycle reactions to occur?
All but option A: the plant is exposed to light condition must be present for the Calvin cycle reactions to occur.
What is the Calvin cycle?The Calvin cycle is the biochemical process that takes place in the chloroplasts of plants, in which carbon dioxide is fixed into glucose molecules. This process involves several enzymes and molecules, but the energy needed to power the process comes from ATP and NADPH, which are produced during the light-dependent reactions that take place in the thylakoid membranes of the chloroplasts.
Therefore, light is required for the Calvin cycle to occur since it is the source of the energy that drives the reaction. However, all parts of the plant do not need to be exposed to light for the Calvin cycle to occur. Only the chloroplasts, which are found in the mesophyll cells of the plant, need to be exposed to light for photosynthesis to occur.
Learn more about Calvin cycle from
https://brainly.com/question/920840
#SPJ1
See full question below
all but which condition must be present for the calvin cycle reactions to occur?
The plant is exposed to light
water is not involved in any of the reactions
light energy is converted into chemical energy
provide the electrons needed to reduce NADP
a uniform meter stick is in static rotational equilibrium when a mass of 220 g is suspended from the 5 cm mark, a mass of 120 g is suspended from the 90 cm mark, and the support stand is placed at the 40 cm mark. what is the mass of the meter stick?
The meter stick is in static rotational equilibrium, which means that the sum of the clockwise torques must equal the sum of the counterclockwise torques. The torque is equal to the force multiplied by the distance from the support point, so we can set up the equation:
CW Torque (5 cm mark): 220 g x 5 cm = 1100 g-cm
CW Torque (90 cm mark): 120 g x 90 cm = 10,800 g-cm
CCW Torque (40 cm mark): M x 40 cm = M x 40 cm
1100 g-cm + 10,800 g-cm = M x 40 cm
M = (1100 + 10,800) / 40 = 250 g
Therefore, the mass of the meter stick is 250 g.
Rotational equilibrium refers to the condition in which an object is motionless and still rotating. The condition occurs when the net torque on an object is equal to zero.
Read more about the topic of rotational equilibrium:
rainly.com/question/31142588
#SPJ11
A car’s cooling system contains 25 kg of water. What is the increased change in temperature of the water if 872. 0 kJ of thermal energy is added?
When 872.0 kJ of thermal energy are injected, the temperature of the 25 kg of water in the car's cooling system changes by 35.0 degrees Celsius.
Water's specific heat capacity (J/(gK), or 4,180 J/ (kgK). Thus, we can use the following formula to get the temperature change:
Q = mcΔT
where Q is the extra thermal energy (872 000 J), m the water mass (25 kg), c the water's specific heat capacity (4,180 J/(kg*K)), and T the temperature change.
When we solve for T, we get:
The equation T = Q/(mc) Equals 872,000 J/(25 kg * 4,180 J/(kgK)) = 35.0 °C.
When 872.0 kJ of thermal energy are injected, the temperature of the 25 kg of water in the car's cooling system changes by 35.0 degrees Celsius.
learn more about energy here:
https://brainly.com/question/1932868
#SPJ4
You stand 3.5 m in front of a large mirror, and your little sister stands 2.0 m directly in front of you. At what distance should you focus your camera if you want to take a picture of your sister in the mirror?
Answer:
D = 3.5 m to mirror
d = 1.50 m from mirror to sister
Total distance from camera to sister = d + D = 5.0 m
One object is placed on each shelf in the image above (W, X, Y, Z). The four objects have the same mass, 2.0 kg. Match each object to its potential energy.
Object W 7.84 J 15.7 J 13.4 J 0 J 23.5 J 5.62
Object X
Object Y
Object Z
Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7J and 23.5J, for better understand we have to know the meaning of potential energy.
What is Potential Energy?Potential energy in physics is the energy that an item retains as a result of its location in relation to other objects, internal tensions, electric charge, or other elements. Potential energy develops in systems having components whose configurations, or relative positions, determine the amount of the forces they apply to one another.
Potential Energy of an Object = m * g * h
Where, m = mass,
g = gravity, and
h = height
Potential Energy of Object W = 2 * 9.8 * 0
= 0 J
Potential Energy of Object X = 2 * 9.8 * 0.4
= 7.84 J
Potential Energy of Object Y = 2 * 9.8 * 0.8
= 15.68 J
≈ 15.7 J
Potential Energy of Object Z = 2 * 9.8 * 1.2
= 23.5 J
Therefore, Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7 J and 23.5 J.
To Learn more about Potential Energy, visit:
https://brainly.com/question/1242059
#SPJ1
what factor does not determine how much gravitational potential energy is in an object-earth system?
The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass.
An object-earth system is a system in which an object interacts with the earth by exerting a force of attraction. The object's energy is derived from the work done by gravitational forces when the object is moved away from the earth's surface.
An object in an object-earth system's gravitational potential energy is the work done by gravitational forces on the object when it is moved from a lower position to a higher one in the object-earth system. The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass. The gravitational potential energy of an object in the earth-object system is determined by the distance between the object and the earth's surface. The gravitational potential energy of an object increases as the distance between it and the earth's surface increases.
Learn more about the gravitational potential at brainly.com/question/19768887
#SPJ11
After You Read
1. Give an example in which the distance you travel is different from your
displacement.
The example in which the distance you travel is different from your
displacement will be "Suppose a person starts at point A and walks 5 meters to point B, and then turns around and walks back to point A, covering another 5 meters. The distance traveled by the person is the total length of the path traveled, which is 10 meters (5 meters + 5 meters).
However, the displacement of the person is the change in position from the starting point to the ending point, which is zero. So the distance traveled is different from the displacement, as the person ends up at the same position where they started, despite covering a total distance of 10 meters.
What is displacement?Displacement is a verb that denotes movement or displacement of an object. The definition of displacement is the modification of an object's position.
The term "displacement" refers to a shift in an object's position. It is a vector quantity with a magnitude and direction. The symbol for it is an arrow pointing from the initial location to the ending place. For instance, if an object shifts from location A to position B, its position changes.
Learn more about displacement on:
https://brainly.com/question/14422259
#SPJ1
Find the volume of the solid obtained by rotating the region in the first quadrant bounded by the curves x = 0, y = 1, x = y^7 about the line y = 1. Volume =______
The volume of the solid obtained by rotating the region in the first quadrant bounded by the curves x = 0, y = 1, x = y^7 about the line y = 1 is 0.
To determine the volume of the solid obtained by rotating the region in the first quadrant bounded by the curves x = 0, y = 1, x = y^7 about the line y = 1, we need to use a specific integral formula.
The volume of the solid is calculated by multiplying the area of the cross-section of the solid, which is perpendicular to the axis of rotation, with the distance traveled by the center of mass of the cross-section. And, when this product is summed up across the length of the solid, we get the volume of the solid.
To solve the given problem, the area of the cross-section of the solid is [tex]\pi (r)^2[/tex], where r is the distance from the line y = 1 to the curve [tex]x = y^7[/tex]. Since the cross-section is a circle, we know the area of the cross-section can be represented by the equation of a circle with radius r, which is [tex]\pi (r)^2[/tex].
To find the value of r, we will equate [tex]x = y^7[/tex] to the line y = 1. By solving for y, we get: [tex]y = 1^{1/7} = 1[/tex].
Hence, r = 1 - 1 = 0.
We can now compute the volume of the solid using the integral formula:
[tex]V =\int_0^1 \pi (r)^2 dy\\V = \int_0^1 \pi (0)^2 dy\\V = \int_0^1 0 dy\\V = 0[/tex]
Learn more about volume of the solid here:
https://brainly.com/question/24259805
#SPJ11
A block of weight w = 25.0 N sits on a frictionless inclined plane, which makes an angle 8 = 29.0° with respect to the horizontal, as shown in the figure. (Figure 1) A force of magnitude F = 12.1 N, applied parallel to the incline, is just sufficient to pull the block up the plane at constant speed.
Part B: What is We, the work done on the block by the force of gravity was the block moves a distance L = 3.40 m up the incline?
Part C. What is Wf the work done on the block by the applied force F as the block moves a distance L = 3.40 mm up the incline? Express your answer in Joules
a) The net Work done is zero. b) The work done on the block by the applied force F as the block moves a distance L is -41.2 J. c) The work done on the block by the applied force F as the block moves a distance L is 41.2 J.
Given:
Weight of the block (w) = 25.0 N
Distance moved by the block (d) = 3.40 m
The angle of the inclined plane (θ) = 29.0°
a) we know that from the work-energy theorem,
W = change in kinetic energy
But since speed is constant which means no change in KE, hence the net Work done is zero.
b) W = -mgy
W = -25 × (3.10 × sin29°)
W = -41.2 J
Therefore, the work done on the block by the force of gravity is -41.2 J.
c) The work done on the block by the applied force F as the block moves a distance L = 3.10m up the incline is,
W = Fd
W = 12.1 × 3.1
W = 41.2 J
Therefore, the work done on the block by the applied force F as the block moves a distance L is 41.2 J.
To know more about the work done:
https://brainly.com/question/26622905
#SPJ12
What is gravity for Galileo?
Galileo famously observed that objects of different masses fall to Earth at the same rate, regardless of their mass. This observation led him to conclude that gravity was a universal force of attraction between any two objects with mass.
Galileo Galilei was an Italian astronomer, physicist, and mathematician who contributed greatly to the development of modern science. His contributions to physics include the creation of the scientific method and his work on the principles of motion and gravity.
Galileo was one of the first scientists to study gravity. He observed that objects of different weights would fall at the same rate when dropped from the same height. This led him to conclude that gravity is a constant force that acts upon all objects equally, regardless of their weight or composition.
Galileo's work on gravity laid the foundation for the later development of Sir Isaac Newton's theory of gravity. Newton built on Galileo's findings and formulated the law of universal gravitation, which states that every object in the universe attracts every other object with a force that is proportional to their masses and inversely proportional to the square of the distance between them.
Learn more about Galileo at https://brainly.com/question/4966012
#SPJ11
if the average arterial pressure at your heart is a typical 100 mmhg , what is the average arterial pressure in your hands when they are held at your side? assume your hands are 60 cm below your heart.
The average arterial pressure in your hands when they are held at your side is 47.5 mmHg.
The average arterial pressure in your hands when they are held at your side can be determined using the hydrostatic pressure formula, which is a function of height, gravity, and density. When the hands are held at the side, they are 60 cm below the heart, which means they are at a distance of 0.6 m.
The hydrostatic pressure formula is given by
P = ρgh
Where,
P is the pressure, ρ is the density, g is the acceleration due to gravity, and h is the height. We can assume that the density of blood is constant, and we can take the value of g to be 9.81 m/s², the standard acceleration due to gravity.
Therefore, the pressure at the heart is 100 mmHg, or 100/760 = 0.131 atm. The pressure in the hands can be calculated as follows:
P = ρghP = (1.06 × 10³ kg/m³) × (9.81 m/s²) × (0.6 m)
P = 6.26 × 10³ N/m²
P = 6.26 × 10³ Pa
P = 47.5 mmHg
Therefore, the average arterial pressure in the hands when they are held at the side is 47.5 mmHg.
Learn more about hydrostatic pressure at https://brainly.com/question/28206120
#SPJ11
T/F the construction of psychological profiles is a process of mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones.
The statement the construction of psychological profiles is a process of mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones is TRUE.
Psychological profiling is a technique used by law enforcement agencies to identify the characteristics of an offender based on their behavior patterns, motives, and other psychological traits. It is a process of creating a psychological profile of an offender by analyzing the crime scene, victimology, and other evidence related to the crime.
This profile is then compared with the profiles of previously solved crimes to identify potential suspects or patterns that can be used to solve unsolved crimes. The process involves mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones.
The psychological profile is based on the assumption that an offender's behavior is consistent across different crimes and that it reflects their personality traits and motivations. This technique has been used successfully in many high-profile cases and has helped law enforcement agencies to identify and apprehend serial offenders.
To know more about psychological profiles, refer here:
https://brainly.com/question/30398442#
#SPJ11
Hominin remains have been found at sites throughout Africa, Europe, and Asia. Below are five of these fossil sites and their main finds. Place them in order from the oldest (earliest in fossil record = most ka) to the youngest (most recent in fossil record = least ka).
1. Omo Kibish: incomplete fossil skull (oldest)
2. Herto: a skull intermediate between H. heidelbergensis and modern H. sapiens
3. Klasies River: fragmentary hominin remains
4. Tianyuan Cave: modern human maniple and femur (youngest)
Hominin remains have been found at sites throughout Africa, Europe, and Asia. Below are five of these fossil sites and their main finds. The correct order of the given hominin fossil sites from oldest to youngest is Omo kibish, Klasies river, Herto, and Tianyuan cave.
Omo kibish is incomplete fossil skull (oldest)The oldest fossil site on the list is Omo kibish in Ethiopia, which is dated to around 195,000 years ago. The site has a partial skull, lower jawbone, and a few other fragments of the skull. Klasies river is fragmentary hominin remains Klasies river Mouth in South Africa is dated back to around 120,000 years ago. The site contains human fossils along with the remains of other animals.
Herto is a skull intermediate between H. heidelbergensis and modern H. sapiens, Herto Bouri in Ethiopia, dated to around 160,000 years ago. The site contains 3 complete hominid skulls which were much more modern than expected for their age. The skulls were similar to Homo sapiens, but with some differences. Tianyuan cave is modern human maniple and femur (youngest). Tianyuan cave in China, dated to around 40,000 years ago, contains one of the earliest modern human fossils. A complete set of human teeth and bones from a foot, leg, and hand were found at this site.
Learn more about hominin at:
https://brainly.com/question/30791663
#SPJ11
what do you think might be causing the fluids in the lava lamp to move?
The fluid movement in a lava lamp is caused by the heat generated from the lamp's light bulb, which causes the wax or oil to rise and fall.
A lava lamp contains two fluids of different densities that do not mix. The fluids heat up as a result of the lamp's light bulb, causing them to expand and become less dense. The wax or oil floats up when it becomes less dense than the fluid that surrounds it, creating a globe at the top of the lamp.
The fluid is then cooled by the environment and becomes more dense, causing the wax to sink back to the bottom. This constant motion cycle creates the flowing effect seen in a lava lamp.
The heat from the light bulb causes the fluid to expand, and as it does, it becomes less dense than the surrounding fluid, causing it to float. When the fluid cools, it becomes denser and settles back down to the bottom. This cyclic motion creates the soothing flow of a lava lamp.
For more such questions on lava lamp, click on:
https://brainly.com/question/30542979
#SPJ11
Need help on my homework! Thanks.
Answer: Noble Gases (Blue)
what is the interference if: distance between a and b is 10mu distance between b and c is 15mu observed double crossover rate is: 0.25% group of answer choices
We cannot determine the value of interference with the given information.
The interference can be determined using the following formula:
interference = (observed double crossover rate - expected double crossover rate) ÷ (1 - expected double crossover rate).
The expected double crossover rate can be calculated using the formula:
expected double crossover rate = (distance AB × distance BC) ÷ total distance (AB + BC + AC).
Given:
Distance between A and B is 10mu;
Distance between B and C is 15mu;
Observed double crossover rate is 0.25%.
Therefore,
Distance AB = 10mu;
Distance BC = 15mu;
Total distance = AB + BC + AC
Expected double crossover rate = (10 × 15) ÷ (10 + 15 + AC)
expected double crossover rate = 150 ÷ (AC + 25)
The observed double crossover rate is 0.25%.
Therefore, the observed double crossover rate = 0.25% = 0.0025.
Interference = (observed double crossover rate - expected double crossover rate) ÷ (1 - expected double crossover rate)=
[0.0025 - (150 / (AC + 25))] ÷ [1 - (150 / (AC + 25))]
what is the interference if: distance between a and b is 10mu distance between b and c is 15mu observed double crossover rate is: 0.25%
To learn more about interference:https://brainly.com/question/16098226
#SPJ11
A small cube of iron is observed under a microscope. The edge of the cube is 5.00×10 cm long. Find (a) the mass of the cube and (b) the number of iron atoms in the cube The molar mass of iron is 55.9g/mol, and its density is 7.86g/cm³.
Answer:
Explanation:
a) The mass of the cube can be calculated using the equation Mass = Volume x Density. The volume of the cube can be calculated as (5.00×10 cm)^3 = 125 cm³. Substituting this volume into the equation gives Mass = 125 cm³ x 7.86 g/cm³ = 983.5 g.
b) The number of iron atoms in the cube can be calculated using Avogadro's number (6.02 x 10^23 atoms/mol). The number of moles can be calculated using the molar mass of iron, 55.9 g/mol. Thus, the number of moles can be calculated as 983.5 g / 55.9 g/mol = 17.61 moles. Multiplying this by Avogadro's number gives the number of iron atoms in the cube as 1.07 x 10^24 atoms.
Suppose you are constructing a 95% confidence interval for the mean of a single sample, whose population standard deviation is known to be σ = 5. You calculate the sample size with some specified width (error) E. (a) Reducing your confidence level to 80%, and reducing your original width (error) E by a third ( 1 3 ), how much bigger will the new sample size be compared to the first sample size above? (Hint: find the scaled size using algebra). b) Suppose instead that your increase the sample size by a factor of 10 and you allow the confidence level to be 85%, how will the width (error) have scaled in size compared to the original width (error) E?
The sample size with some specified width error by reducing the confidence level to 80% is 3 times the original sample size and the width error which have been scaled in size compared to the original width error is by a factor of 10.
What is the sample size?When reducing the confidence level to 80% and the original width (error) E by a third, the new sample size will be 3 times the original size. To calculate this, use the formula n = (zα/2 / E)² × σ2.
If the original confidence level was 95%, then the original zα/2 = 1.96. If the new confidence level is 80%, then the new zα/2 = 1.282.
The original error was E, and the new error is 1/3 E. By substituting these values into the formula, we get n = (1.282 / (1/3 E))² × σ2. This simplifies to n = 3 × (1.96 / E)² × σ2, which is 3 times the original sample size.
If the original confidence level was 95%, then the original zα/2 = 1.96.
If the new confidence level is 85%, then the new zα/2 = 1.44.
The original error was E, and the new error is 10E.
By substituting these values into the formula, we get n = (1.44 / (10E))² × σ2.
This simplifies to n = (1.96 / E)² × σ2, which is 10 times the original sample size.
Therefore, the width (error) will have scaled in size by a factor of 10 compared to the original width (error) E.
Learn more about Sample size here:
https://brainly.com/question/25894237
#SPJ11
An electric lamp consumes 60 watts at 220 volts. How many dry cells of EMF 1. 5 volt and internal resistance 1 ohm are required to glow the lamp?
We must figure out the total voltage and current required to generate 60 watts of electricity in order to calculate the number of dry cells necessary to light the bulb.
Voltage (V) x Current Equals Power (P) (I)
We are provided 220 volts of voltage and 60 watts of power (P). Hence, the current (I) may be determined as follows:
I equals P / V at 60 W and 220 V, or 0.273 A.
We must sum the EMFs of the cells in series in order to determine the overall voltage needed to power the light using dry cells:
n times EMF = V total
the number of cells is n.
Since the EMF of each cell is 1.5 volts, the total voltage needed may be written as follows:
1.5 n V total
learn more about electricity here:
https://brainly.com/question/8971780
#SPJ4
In the context of the motor control process related to the speed-accuracy trade-off, the _____ phase of movement includes the beginning of limb movement in the direction of a target.
In the context of the motor control process related to the speed-accuracy trade-off, the initiation phase of movement includes the beginning of limb movement in the direction of a target.
What is motor control?Motor control is the ability to regulate and coordinate motor skills to achieve a desired outcome. The central nervous system (CNS) is in charge of regulating these skills. The CNS is divided into two parts: the peripheral nervous system (PNS) and the central nervous system (CNS). Motor skills are regulated by both parts of the nervous system. The CNS, on the other hand, is more involved in higher-level motor control.
A motor control system can be divided into three stages: planning, initiation, and execution. When the central nervous system processes the desired movement, it activates the motor program in the initiation stage, which produces the motor command sent to the muscles. Movement is initiated by the initiation stage. Following that, the movement is executed to meet the task's requirements. The motor program adjusts movement by making corrections based on previous trials and feedback. Therefore, the initiation phase is critical in the context of the motor control process related to the speed-accuracy trade-off.
Learn more about Motor control here:
https://brainly.com/question/29769703
#SPJ11
the range of frequencies on the electromagnetic spectrum called by?
The range of frequencies on the electromagnetic spectrum is known as the electromagnetic spectrum.
The spectrum ranges from radio waves, microwaves, infrared waves, visible light, ultraviolet rays, x-rays, and gamma rays. Each type of wave has a specific frequency range, ranging from hertz (Hz) to exahertz (EHz). The lowest frequency waves, such as radio waves, range from 3 kHz to 300 GHz, while the highest frequency waves, such as gamma rays, range from 300 GHz to 3 EHz.
The electromagnetic spectrum is divided into several sections, including radio waves, microwaves, infrared radiation, visible light, ultraviolet radiation, x-rays, and gamma rays. Each type of wave has its own properties and uses in different applications. Radio waves are used for communication, microwaves are used in satellite communication and imaging, infrared radiation is used in medical imaging, visible light is used to see our environment, ultraviolet radiation is used in sun protection and sterilization, x-rays are used in medical imaging and treatment, and gamma rays are used in medical treatment and research.
for such more question on electromagnetic spectrum
https://brainly.com/question/13803241
#SPJ11
calculate the fluid force on one side of a 5ft by 5ft square plate if the plate is at the bottom of a pool filled with water to a depth of 8ft and, a. lying flat on its 5ft by 5ft face. b. resting vertically on a 5 ft edge c. resting on a 5 ft edge and tilted at 45 degrees to the bottom of the pool.
The fluid force on one side of the 5ft by 5ft plate lying flat on its 5ft by 5ft face, we can use the equation F = ρghA and the F = 1,945,000 N.
What is the fluid force?Since the plate is at the bottom of the pool and the pool is filled with water to a depth of 8ft, h = 8ft and the area of the plate A = 5ft × 5ft = 25ft².
There F is the fluid force, ρ is the density of the fluid, g is the acceleration due to gravity, h is the depth of the fluid, and A is the area of the plate.
Therefore, the fluid force on one side of the plate is:
F = ρghA = 1000kg/m³ × 9.81m/s² × 8ft × 25ft² = 1,945,000 N.
To calculate the fluid force on one side of the plate resting vertically on a 5 ft edge, we can use the same equation as above but with an area equal to the length of the plate multiplied by the depth of the pool (8ft):
F = ρghA = 1000kg/m³ × 9.81m/s² × 8ft × 5ft = 392,000 N.
To calculate the fluid force on one side of the plate resting on a 5ft edge and tilted at 45 degrees to the bottom of the pool, we can use the same equation as above but with an area equal to the length of the plate multiplied by the depth of the pool multiplied by the cosine of the angle of the plate:
F = ρghA = 1000kg/m³ × 9.81m/s² × 8ft × 5ft × cos(45) = 283,200 N.
Read more about the force here:
https://brainly.com/question/12785175
#SPJ11
A slingshot sends a stone vertically upward from a height of 20 feet above a pool of
water. The starting speed of the stone is 90 feet per second. Its distance in feet, d.
above the water is given by the equation:
d-20+90t-16t^2, where t is the time in seconds after the launch.
Drag statements to the table to show what each coordinate labeled on the graph
represents in this problem situation.
the height of the stone when it is launched
the time when the stone hits the water
the time when the stone is launched the maximum height of the stone
the time when the stone reaches its maximum height
Coordinate
A
the height of the stone when it hits the water
What the Coordinate Represents
DRAG AND DROP
AN ITEM HERE
DRAG AND DROP
AN ITEM HERE
DRAG AND DROP
DRAG AND DROP
Coordinate , A - the height of the stone when it hits the water. A slingshot sends a stone vertically upward from a height of 20 feet above a pool of water.
What the Coordinate Represents?The coordinate A represents the height of the stone when it hits the water. When the stone hits the water, its height above the water surface is zero.
So, we can set the expression for the stone's height equal to zero and solve for t to find the time when the stone hits the water. The height of the stone when it is launched is given as 20 feet, which is a fixed value in this problem.
The time when the stone is launched is also a fixed value, which is zero. The maximum height of the stone is the highest point the stone reaches above its initial height of 20 feet. The time when the stone reaches its maximum height is the time at which the vertical velocity of the stone becomes zero.
To know more about vertical velocity , visit :
https://brainly.com/question/11679227
#SPJ1
what would happen to the gravitational force between the sun and sirius, another main sequence star, if the mass of sirius were to triple?
Answer:
It would triple.
Explanation:
By Newtown's law of universal gravitation, the ration is 1:1
when an electron releases energy what form does it take?
Answer:
Light energy
Explanation:
When an electron releases or absorbs energy, it goes into an "exited state" which means it goes into a lower or higher energy level respectively. This will radiate light energy.
a missile of mass 1.20 102 kg is fired from a plane of mass 4.80 103 kg initially moving at a speed of 3.25 102 m/s. if the speed of the missile relative to the plane is 1.06 103 m/s, what is the final velocity of the plane?
The final velocity of the plane after a missile of mass 1.20 102 kg is fired from the plane is 0.255 m/s.
To find the final velocity of the plane when a missile of mass 1.20 x 10² kg is fired from a plane of mass 4.80 x 10³ kg initially moving at a speed of 3.25 x 10² m/s, and the speed of the missile relative to the plane is 1.06 x 10³ m/s, we can use the conservation of momentum.The initial momentum of the system is given by:
m1v1 + m2v2 = (m1 + m2)vf
where m1 = mass of missile, m2 = mass of the plane, v1 = velocity of the missile, v2 = velocity of the plane, and vf = final velocity of the system
Substituting the given values, we get:(1.20 x 10² kg) (1.06 x 10³ m/s) + (4.80 x 10³ kg) (3.25 x 10² m/s) = (1.20 x 10² kg + 4.80 x 10³ kg) vf
Simplifying, we get:1284 = (5.04 x 10³ kg) vf
Therefore, vf = 1284 / (5.04 x 10³ kg) = 0.255 m/s. So, the final velocity of the plane is 0.255 m/s.
More on velocity: https://brainly.com/question/20038545
#SPJ11
4. write all of the proper subset relations that are possible using the sets of numbers n, z, q, and r
The proper subset relations that are possible using the sets of numbers n, z, q, and r are:
n ⊆ z, q, and rz ⊆ n, q, and rq ⊆ n, z, and rr ⊆ n, z, and qAn improper subset comprises every element of the original set, while a valid subset only contains a fraction of the original set's numbers. A subset of a set A that is not equal to A is a proper subset of A. In other words, if B is a proper subset of A, then A has at least one element that is not in B but all of B's elements are in A.
Learn more about proper subset at brainly.com/question/17514113
#SPJ11
what's the correct answer.
The coordinated functions of the Nervous, Endocrine, and Reproductive systems are:
D. CerebrumN. Wernicke's AreaF. Occipital LobeH. HypothalamusJ. ThalamusH. HypothalamusC. CerebellumL. Superior ColliculusA. AmygdalaM. Pineal GlandWhat are coordinated functions?Coordinated functions refer to the integration and communication between different organs, systems, and tissues in the body to achieve a common goal or purpose. In biological terms, coordinated functions often involve multiple physiological systems working together to maintain homeostasis, respond to stimuli, or carry out complex behaviors or processes.
Examples of coordinated functions include the regulation of blood glucose levels by the pancreas and liver, the coordination of movement by the nervous and musculoskeletal systems, and the release of hormones by the endocrine system to control various physiological processes.
Learn more on coordinated functions here: https://brainly.com/question/15686131
#SPJ1
The question is:
"COORDINATED FUNCTIONS OF THE NERVOUS, ENDOCRINE, AND REPRODUCTIVE SYSTEMS"
Directions: Identify the part of the brain that is involved in each situation below. Write only the letter of your answer.
A. Amygdala
B. Brocka's Area
C. Cerebellum
D. Cerebrum
E. Hippocampus
F. Occipital Lobe
G. Hippocampus
H. Hypothalamus
I. Inferior Colliculus.
J. Thalamus
K. Pons
L Superior Colliculus
M. Pineal Gland
N. Wernicke's Area
O. Pituitary Gland
1. "My heart tells me that you are the one. I love you so much!"
2. "IAOCEVOY! I don't know what that means. It's all Greek to me!"
3. "Chartreuse, Olive,Turquoise, and Mint are all shades of green."
4. "Janna always wakes up at 4 in the morning, regardless of whether she uses an alarm clock or not."
5. "I don't remember the way going to Myla's house. Can you accompany me there?"
6. Jenny's mother is about to give birth, she complains about contraction and pain usually when the baby is kicking
7. "Anthony is a very skilled dancer. He just won the school hip hop dance competition last week."
8. "As Nica was walking on the road she readily moved to the side for she heard an incoming ambulance"
9. "Elsa loves making faces whenever she talks to her friends."
10. "Ryan usually talks about how happy his high school days were to his grandchildren."
true or false? a faraday bag stops any electromagnetic emanations from passing into or out of the bag, preventing a mobile device from communicating with the outside world. true false
True. A Faraday bag (also known as an electromagnetic bag) is a container made from metal or a special material that blocks any electromagnetic emanations from passing into or out of the bag, preventing a mobile device from communicating with the outside world.
This is because Faraday bags are electromagnetic bags that are designed to isolate electronic devices from external electromagnetic influence. They are also known as radiofrequency shielding bags, Faraday cage bags, signal blocker bags, or electromagnetic pulse (EMP) bags.
What are Faraday bags?
Faraday bags are made of a combination of metal or metal-coated fabrics that are designed to block electromagnetic signals from entering or leaving the bag. They are usually used to keep mobile devices such as smartphones and tablets from communicating with the outside world, especially in situations where an individual is worried about their privacy or security. They are also used by law enforcement agencies to prevent suspects from remotely wiping or deleting evidence on their devices.
How do Faraday bags work?
Faraday bags work by using a principle known as the Faraday effect, which states that any electric field in a conductor is shielded from the conductor's interior by the presence of an electric field. Faraday bags use this principle to block incoming and outgoing signals by creating an electrically conductive enclosure around the device. This means that when a mobile device is placed inside a Faraday bag, the bag acts as a Faraday cage, which shields the device from electromagnetic radiation. As a result, the device cannot communicate with the outside world.
For further details about Faraday bag, click on the below link:
https://brainly.com/question/23083952
#SPJ11
Which method will NOT reduce reactivity of observation?a) observe through a one-way observation window b) tell the person you are observing his/her behaviorc) wait until the person you are observing is accustomed to your presenced) use participant observers
One of the methods which will not reduce reactivity of observation is telling the person you are observing his/her behaviour. Correct option is B.
A practical, utilitarian approach, behavioral observation focuses on the plainly discernible ways in which the client engages with his or her surroundings. Behavioural observation can be used as a standalone technique or casually as a component of an interview, a test, or both.
Waiting until the subjects of the observation are used to the observer is one method to reduce reactivity. Another option is to have the observer document the actions without the subjects being aware of the observation.
The act of observation modifies in some manner the situation in which a participant is being observed. Within an experimental setting, reactivity is viewed as a threat to internal validity because the change in behaviour is not due to the experimental manipulation. Best choice is B.
To know more about observations:
https://brainly.com/question/30454101
#SPJ4
