Answer:
a. Rockwell 3. hardness
b. Instron 2. stress vs strain
c. Charpy 1. impact strength
d. Fatigue 4. Endurance Limit
e. Brinell 3. hardness
f. Izod 1. impact strength
Explanation:
Izod and Charpy are the impact strength testing procedure of a material in which a heavy hammer is attached to an arm is released to impact on the test specimen. In Izod test the specimen with v-notch is held vertical with the notch facing outward while in Charpy test the specimen is supported horizontally with notch facing inward to the impacting hammer.
Instron testing system does universal testing of the material which gradually applies the load recording all the stresses and the corresponding strains until the material fails.
Fatigue is the property of a material due to which it fails under the repeated cyclic loading by the initiation and propagation of cracks. The property of a material resist failure subjected to infinite number of repeated cyclic loads below a certain stress limit.
Rockwell and Brinell are the hardness testing methods. In Rockwell test an intender ball is firstly pressed against the specimen using minor load for a certain time and then a major load is pressed against it for a certain time. After the intender is removed the depth of impression on the surface is measured while in case of Brinell hardness we apply only one load against the intender ball for a certain time and after its removal the radius of impression is measured.
số bit của pic 16f887
Answer:
what does it mean
Explanation:
sorry
plz write in English
A mechanic claims to have developed a car engine that runs on water instead of gasoline. What is your response to this claim?
The claim will be impractical. The reason behind this is provided below throughout the explanation segment.
Inside the same combustion chamber, fresh water can't be pressurized even more than fuel as well as air. Consequently, the cylinder does not burn due to a problem with the compressor.To accomplish the development processes, a machine requires any sort of combustible which might cause combustion as well as create a tremendous quantity of power.
Thus, the idea of using water instead of petroleum appears unworkable throughout traditional engines.
Learn more:
https://brainly.com/question/4067583
Uses of P-N junction
Answer:
Explanation:
Two that come to mind:
a semiconductor diode is essentially a PN junctiona transistor is made of two pn junctions.which type of clectrical circuit is represented by this diagram?
Answer:
parallel
Explanation:
All components in this circuit are tied in parallel. Each component experiences the same voltage from one terminal to the other. It is a parallel circuit.
an atom that gained an electron is called
Answer:
Hey mate......
Explanation:
This is ur answer.....
When an atom gains/loses an electron, the atom becomes charged, and is called an ion.Hope it helps!
Brainliest pls!
Follow me :)
What is the following diagram called?
Answer:
flow chart
Explanation:
it's a flow chart right ? don't know the explanation cause I am not even sure I am right
2 Air enters the compressor of a cold air-standard Brayton cycle at 100 kPa, 300 K, with a mass flow rate of 6 kg/s. The compressor pressure ratio is 10, and the turbine inlet temperature is 1400 K. The turbine and compressor each have isentropic efficiencies of 80%. For k 5 1.4, calculate (a) the thermal efficiency of the cycle. (b) the back work ratio. (c) the net power developed, in kW. (d) the rates of exergy destruction in the compressor and turbine, respectively, each in kW, for T0 5 300 K.
if a person is injured at the hospital during a natural disaster a correct action to take is
Rafel knows that lessons learned is a valuable aid to future projects. When should he and his team address
lessons learned on a project?
Select an answer:
Add lessons learned as a topic in status meetings
Review past lessons learned so a new one does not have to be created,
Create lessons learned at the end of the project.
Brainstorm lessons learned at the beginning of a project
Answer: Create lessons learned at the end of the project.
Explanation:
Lessons learned are the experiences that are gotten from a project which should be taken into account for the future projects. Lesson learned are created at the end of the project.
The main objective of the lessons learned is that they show both the positive experience and the negative experience of a project and this will help the future projects that will be undertaken.
A technician wants to implement a dual factor authentication system that will enable the organization to authorize access to sensitive systems on a need-to-know basis. What should be implemented during the authorization stage?
Answer: Biometrics
Explanation:
Dual factor authentication refers to an electronic authentication method whereby a user will only be granted an access to an application or a website after the user has successfully been able to present two pieces of evidence which then grants access to the application or website.
Since the technician wants to implement a dual factor authentication system, the biometrics should be implemented during the authorization stage.
Biometrics refers to the body measurements and the calculations that are related to the characteristics of humans. Biometric authentication is used as a form of identification.
Why is logging done during drilling?
Answer:
Logging while drilling (LWD) is a technique of conveying well logging tools into the well borehole downhole as part of the bottom hole assembly (BHA). ... In these situations, the LWD measurement ensures that some measurement of the subsurface is captured in the event that wireline operations are not possible
Magnetic particle testing can be done only on metals that can be magnetized.
True or false
. Bơm kiểu piston tác dụng đơn có áp suất p=0,64 Mpa và lưu lượng Q=3,5 l/s. Xác định tốc độ quay của trục bơm và công suất của bơm nếu biết đường kính piston D=150 mm; bán kính tay quay R=60 mm; hiệu suất thể tích của bơm là 0=0,94; hiệu suất chung của bơm b=0,80.
Answer:
not understand language
Explain the 11 sections that a typical bill of quantity is divided into
Answer:
The main sections included in the bill of quantities are Form of Tender, Information, Requirements, Pricing schedule, Provisional sums, and Day works.
A bird is flying in air. It is stretching its wings all along the sky and is flying in a certain direction Flying a bird is an example of: a. Composition of vector b. Collinear vector c. Addition of vector d. Multiplication of vector
Answer:
a. Composition of Vector.
Explanation:
When a bird flies in the air, it stretches its wings into air and this movement helps it move in a certain direction. This is an example of composition of vector. Air strikes the wings in opposite direction and bird wing movement helps it move against the wind.
You toss two coins. If you get heads with the first coin, you stop. If you get tails, you toss it again. The second coin is tossed regardless. What is the ratio of heads to tails?
Answer:
1:1
Explanation:
A coin has either a head or tail.
Thus, probability of head = ½
Probability of tail = ½
The first coin is tossed twice and probability of head or tail on both tosses is still ½. Thus, they will have a ratio 1:1.
The second coin is still tossed regardless and thus continuously and so should have same ratio of 1:1.
Therefore, the ratio of the both of them must, also be 1:1.
A steam turbine generator unit is used to produce electricity, where steam enters the turbine with a velocity of 30 m/s and enthalpy (internal energy) of 3348 kJ/kg. The 1 steam leaves the turbine as a mixture of vapor and liquid having a velocity of 60 m/s and an enthalpy of 2550 kJ/kg. The flow through the turbine is adiabatic, and changes in elevation are negligible. Determine the work output from the turbine, if the mass flow rate is 5kg/s.
Answer:
3.983 MW
Explanation:
Given that:
At the inlet:
Velocity (v₁) = 30 m/s
Enthalpy (h₁) = 3348 kJ/kg
At the outlet:
Velocity (v₂) = 60 m/s
Enthalpy (h₂) = 2550 kJ/kg
Mass flow rate (m) = m₁ = m₂ = 5kg/s
According to the steady flow energy equation:
[tex]Q+ m_1 (h_1 + \dfrac{v_1^2}{2000}+ \dfrac{gz_1}{1000} )= m_2(h_2+\dfrac{v_2^2}{2000}+\dfrac{gz_2}{1000})+W_{shaft}[/tex]
Since the elevation (z) is negligible and flow via the turbine is adiabatic:
Then,
Q = 0 and z₁ = z₂
∴
[tex]W_{shaft} = (mh_1-mh_2) + (\dfrac{mv_1^2-mv_2^2}{2000})[/tex]
[tex]W_{shaft} = ((5*3348) -(5*2550)) + (\dfrac{(5*(30)^2)-(5*(60)^2)}{2000})[/tex]
[tex]W_{shaft} = (16740-12750) + (\dfrac{4500-18000}{2000})[/tex]
[tex]W_{shaft} = (16740-12750) + (-6.75)[/tex]
[tex]W_{shaft} = 3983.25 \ kW[/tex]
[tex]\mathbf{W_{shaft} = 3.983 \ MW}[/tex]
anxiety: a. is never normal. b. is common of many psychological disorders c. is identical to fear d. is a modern development, unlikely to have roots in human history
Answer:
B
Explanation:
Anxiety is very common especially nowadays but it's especially common in psychological disorders
If a corporation is socially responsible, it will develop and implement a sustainability plan and communicate it to stakeholders.
True
False
Answer:
True
Explanation:
All big companies are pretty much required in today's day and ages to complete these reports whether they truly believe it.
What is the following diagram called?
Answer:
business
Explanation:
because shopping has great income
Answer:
is ur question right
Explanation:
is ur question right
is ur question right
True or false: You can create a network with two computers.
Answer
True
beacuse thye want them to hav egoood and thye wn thme tto
Answer:
I don't understand the question
what is the best book for mechanic of materials?
Answer:
As per my experience Egor Popov is one the best book for mechanics of materials.
Explanation:
hope this helps
Which of the following conditions were present in over 80% of paddling fatalities from 1995-2000?
Answer:
80% of the people that were killed weren't wearing a safety flotation device ( in correct terminology Personal Flotation Device, or PFD )
Explanation:
Hence they drowned due to the lack of safety.
The condition present in over 80% of paddling fatalities is that the victims were said to be not wearing a personal flotation device (PFD).
What is paddling in the sea?The act of paddling is known to be a sport or something one can do for fun or for games.
Conclusively, a lot of paddling fatalities 1995-2000 was due to the fact that the people who were engage in the sport or act were not putting on a personal flotation device (PFD) and this can lead to death or drowning.
Learn more about paddling fatalities from
https://brainly.com/question/3787626
Consider the following lines of Python:
>>> x = input()
>? 12
>>> x + “abc”
What is the output?
Answer:
I don't know
............................
The output will be an error message since the input() function in Python always takes input as a string, even if the entered value is an integer like 12.
Here,
It cannot directly concatenate a string with an integer.
In order to fix this, we need to convert the input string into an integer using the int() function,
```
x = int(input())
x = x + "abc" # this will give an error message
```If we fix the code, the correct output will be:
`>>> x = int(input())`
`12`
`>>> x + "abc"`
`TypeError: unsupported operand type(s) for +: 'int' and 'str'`
Know more about python,
https://brainly.com/question/11288191
#SPJ4
You are given a pot of hot tea (350 mL) at a temperature of 85°C and a quantity of ice at -12°C. Determine the absolute minimum amount of ice you can add to the hot tea so that at equilibrium you have iced tea (ie. a very, very small amount of ice and some water). You can assume tea has the same density (1.00 g/mL) and specific heat (4190 J/kgK) as liquid water. The heat of fusion of H2O is 3.33x10^5 J/kg. The specific heat of ice is 2090 J/kgK.
Answer:
348 g
Explanation:
The heat gained by the ice equals the heat lost by the hot tea.
Also, since we require a very, very small amount of ice and some water, to still have some ice, the temperature of the hot tea has to decrease to the melting point of ice which is 0°C. So, the final temperature of the mixture is 0 °C.
So, mc(T - T') + mL = -MC(T - T") where m = mass of ice, c = specific heat of ice = 2090 J/kgK., T = final temperature of mixture = 0 °C, T' = initial temperature of ice = -12 °C, L = heat of fusion of H2O = 3.33 × 10⁵ J/kg, M = mass of hot tea = ρV where ρ = density of tea = 1.00 g/mL and V = volume of hot tea = 350 mL. So, M = ρV = 1.00 g/mL × 350 mL = 350 g = 0.350 kg, C = specific heat of tea = 4190 J/kgK and T" = initial temperature of tea = 85 °C.
Making m subject of the formula, we have
mc(T - T') + mL = -MC(T - T")
m[c(T - T') + L] = -MC(T - T")
m = -MC(T - T")/[c(T - T') + L]
substituting the values of the variables into the equation, we have
m = -MC(T - T")/[c(T - T') + L]
m = -0.350 kg × 4190 J/kgK(0 °C - 85 °C.)/[2090 J/kgK(0 °C. - (-12 °C)) + 3.33 × 10⁵ J/kg]
m = -1466.5 J/kK(- 85 °C)/[2090 J/kgK(0 °C + 12 °C)) + 3.33 × 10⁵ J/kg]
m = 124652.5 J/[2090 J/kgK(12 °C) + 3.33 × 10⁵ J/kg]
m = 124652.5 J/[25080 J/kg + 3.33 × 10⁵ J/kg]
m = 124652.5 J/358080 J/kg
m = 0.3481 kg
m = 348.1 g
m ≅ 348 g
So, the minimum amount of ice to be added is 348 g.
biến tần là gì trong công nghiệp
Nguồn điện là một yêu cầu thiết yếu của các ngành công nghiệp. Biến tần là một thiết bị độc lập có chức năng chuyển đổi điện áp một chiều thành điện áp xoay chiều. Biến tần đảm bảo rằng việc cung cấp điện không bị gián đoạn và liên tục. ... Các ngành công nghiệp yêu cầu sử dụng bộ nghịch lưu công nghiệp để hoạt động liên tục của các hoạt động trong ngành.
Work to be performed can come from the work package level of the work breakdown structure as well as other sources. Which of these is NOT a source of authorized work to be performed?
a. Scope creep
b. Defect repairs
c. Preventive actions
d. Corrective actions
A project is meant to achieve clearly defined goals within present constraints
The correct option for the source of work in a project which is NOT a source of authorized work to be performed is option (a)
a. Scope creep
The reason for the selecting the above option is as follows;
In project management, alongside work planned in a work package, authorized work to be performed can come from;
The repairing of defects found in completed work and which is a requirement for the project to be approvePreventive actions, that are meant to mitigate factors that affect the project timeline and costCorrective actions which include actions meant to rectify parts of the project that produce an error outcomeA scope creep, however, is generally is due to the inclusion of the end
users of the project at a time that is behind schedule, insufficient analysis of
the requirements, and project complexity underestimation. and consists of
changes made after a project has commenced
A scope creep therefore, changes the amount of work to be done which
therefore alters the project timeline, and due to project, budgetary, and
end user constraints, CANNOT be a source of authorized work to be
performed
The correct option for the source that is NOT a authorized work to be performed is option a. Scope creep
Learn more about scope creep here:
https://brainly.com/question/14061926
Troy must keep track of the amount of refrigerant he uses from a 50-pound cylinder to ensure that accurate
records are kept. He used 13 pounds on a systein for Ms. Jones and 9 pounds on a system for a commercial
client. How many pounds should he have left in the cylinder?
tof
Troy should have
pounds of refrigerant left in the cylinder.
baon naid Thamar basic
محمود احمد مجد
12
اهداء ما در
Answer:
Amount of gas still in cylinder = 28 pound
Explanation:
Given:
Amount of gas in cylinder = 50 pound
Amount of gas used in Ms. Jones system = 13 pound
Amount of gas used in client system = 9 pound
Find:
Amount of gas still in cylinder
Computation:
Amount of gas still in cylinder = Amount of gas in cylinder - Amount of gas used in Ms. Jones system - Amount of gas used in client system
Amount of gas still in cylinder = 50 - 13 - 9
Amount of gas still in cylinder = 28 pound
Functional and nonfunctional requirements documents are used to _____.
define the financial budget of a system
define the purpose of a system
facilitate communication between the users and a system
help exercise control over the inner workings of the firm.
Answer:
Non-functional requirements when defined and executed well will help to make the system easy to use and enhance the performance
Explanation:
