In a typical transmission line, the current I is very small and the voltage V is very large. A unit length of line has resistance R. For a power line that supplies power to 10,000 households, we can conclude that:________

Answers

Answer 1

Answer:

IV > [tex]I^{2} R[/tex]

Explanation:

The current in the power line = I

The voltage in the power line = V

The resistance of the power line = R

Power supplied from the power house = P

power delivered to the households = [tex]p[/tex]

We know that the power supplied to a power line system is proportional to

P = IV    ....1

we also know that according to Ohm's law, the relationship between the voltage, resistance, and current through an electrical system is given as

V = IR    ....2

substituting equation 2 into equation 1, the power delivered to the households is proportional to the square of the current.

[tex]p[/tex] = [tex]I^{2} R[/tex]    ....3

The problem is that when power is delivered across a transmission line, some of the power is loss due to Joules heating effect of the power lines. This energy and power loss is proportional to [tex]I^{2}[/tex] therefore, the electrical power delivered to the households will be less than the electrical power supplied from the power station. This means that

P > [tex]p[/tex]

equating these two powers from equations 1 and equation 3, we have

IV > [tex]I^{2} R[/tex]

In A Typical Transmission Line, The Current I Is Very Small And The Voltage V Is Very Large. A Unit Length

Related Questions

According to the building-up principle or aufbau principle, which subshell is typically filled next after the 3d subshell? A) 4p B) 5f C) 6p D) 5d E) 3p

Answers

According to the building-up principle or Aufbau principle, the subshell is typically filled next after the 3d subshell is the 4p subshell. The correct option is A).

What are subshells?

A subshell is the collection of states within a shell that are indicated by the azimuthal quantum number, l. S, P, D, and F subshells are represented by the values l = 0, 1, 2, and 3, respectively.

The formula for the maximum number of electrons that can fit into a subshell is 2(2l + 1). The highest level of probability for an electron to occur is in an atomic orbital.

The route that electrons travel while navigating the restrictions of the shell is referred to as a subshell. There are four different subshell classifications. The letters s, p, d, and f are used to identify the subshells.

Therefore, the correct option is A) 4p.

To learn more about subshells, refer to the link:

https://brainly.com/question/4177923

#SPJ5

Where are revolved sections placed in a print? A) in between break lines B) cutting planes are used to identify their locations C) in between section lines D) stand alone

Answers

Answer:

B. Cutting planes are used to identify their locations.

Explanation:

Revolved view is a cross section view of revolved 90 degrees around a cutting plane projections. The revolved view of print will differ from a cross sectional view. It includes a line nothing the axis of revolution for the view. The correct answer is B. The revolved section in the prints has cutting planes that will be used to identify their location.

After clamping a buret to a ring stand, you notice that the set-up is tippy and unstable. What should you do to stabilize the set-up

Answers

Answer:

Move the buret clamp to a ring stand with a larger base.

Explanation:

A right stand is used for titration experiments in the laboratory. It holds the burette firmly during experiments so that accurate readings can be taken.

The right stand is made up of support base, vertical stainless steel, clamp with adjustable screw that holds on to the vertical rod.

The clamp is used to hold the burette in place.

If after clamping a buret to a ring stand, you notice that the set-up is tippy and unstable, the best action will be to move the buret clamp to a ring stand with a larger base.

The larger base provides a better center of gravity and stabilises the setup

Consider the thermocouple and convection conditions of Example 1, but now allow for radiation exchange with the walls of a duct that encloses the gas stream. If the duct walls are at 400℃ and the emissivity of the thermocouple bead is 0.9, calculate the steady-state temperature of the junction

Answers

Answer:

hello your question has some missing part attached below is the complete question

answer : steady state temperature = 419.713k ≈ 218.7⁰c

              Time required to reach a junction ≈ 5 secs

Explanation:

The detailed solution of the given problem is attached below but the solution to the subsequent problem from which the question you asked is referenced to( problem 1 ), is not attached because it was not part of the question you asked

The plate is made of steel having a density of 7910 kg/m3 .If the thickness of the plate is 9 mm , determine the horizontal and vertical components of reaction at the pin A and the tension in cable BC.

Answers

Answer:

Horizontal component ( Ax) = 0

vertical component ( Ay ) = 1794.87 N

Explanation:

Attached below is the detailed solution and the free body diagram of the question

given data:

density = 7910 kg/m3

thickness of plate = 9 mm = 0.009

determine the horizontal and vertical components of the reaction at the pin A and the tension in the cable BC

Match the following light concepts
- Light is bounced back at same angle
- Light penetrates medium at different angle due to different material densities
- Light bounces at different angles in periodic grid
- Light enters medium at different angles through a grid
- Light EMF field looses one axis component
A Polarized filter
B. Transmission Diffraction
C. Classical Reflection
D. Refraction
E. Reflected Diffraction

Answers

Answer:

- Light is bounced back at same angle    (Classical Reflection)

- Light penetrates medium at different angle due to different material densities     (Refraction)

Light bounces at different angles in periodic grid     (Reflected Diffraction)

Light enters medium at different angles through a grid     (Transmission Diffraction)

- Light EMF field looses one axis component     (Polarized filter)

Explanation:

Reflection is a phenomenon in which waves (light included) bounce back from an obstacle at the same angle of incidence

Refraction is the change in the angle of a wave as it enters the interface of two media. The change in angle is due to the difference in the densities of the two media.

Reflected diffraction occurs when an optical component with a periodic grid, splits, and diffracts light into several beams travelling in different directions. The light light bounces at an angle in the periodic grid.

Transmission diffraction is dispersion a beam of various wavelengths into a spectrum of associated lines due to the principle of diffraction. In this type of diffraction, light enters medium at different angles through a grid.

Polarized filters removes one field from the incidence electromagnetic wave like light, leaving it to vibrate in only one plane.

A single-threaded power screw is 35 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 006 for the collar and 009 for the threads, while the frictional diameter of the collar is 45 mm. Find the overall efficiency and the torque to raise and lower the load for

Answers

Answer:

the torque required to RAISE the load is Tr = 18.09 Nm

the torque required to LOWER the load is Tl = 10.069 ≈ 10.07 Nm

the Overall Efficiency e = 0.2199 ≈ 0.22

Explanation:

Given that; F = 5 kN, p = 5mm, d = 35mm

Dm = d - p/2

Dm = 35 - ( 5/2) = 35 - 2.5

DM = 32.5mm

So the torque required to RAISE the load is

Tr = ( 5 × 32.5)/2 [(5 + (π × 0.09 × 32.5)) / ( (π × 32.5) - ( 0.09 × 5))] + [( 5 × 0.06 × 45)/2]

Tr = 81.25 × (14.1892 / 101.6518) + 6.75

Tr = 11.3414 + 6.75

Tr = 18.09 Nm

the torque required to LOWER the load is

Tl =  ( 5 × 32.5)/2 [(π × 0.09 × 32.5) - 5) / ( (π × 32.5) + ( 0.09 × 5))] + [( 5 × 0.06 × 45)/2]

Tl = 81.25 × 4.1892 / 102.5518 + 6.75

Tl = 3.3190 + 6.75

Tl = 10.069 ≈ 10.07 Nm

So since torque required to LOWER the load is positive

that is, the thread is self locking

Therefore the efficiency is

e = ( 5 × 5 ) / ( 2π × 18.09 )

e = 25 / 113.6628

e = 0.2199 ≈ 0.22

Strain gage is a device that senses the strain of the structure. The property of the strain gage that is used to correlate with the strain to be measured is

Answers

Answer:

  resistance

Explanation:

A strain gauge changes resistance with applied strain.

All hermetic compressors require a crankshaft seal.
True
False

Answers

True they are ur welcome

The natural variation of a process relative to the variation allowed by the design specifications is known as

Answers

Answer:

"Process capability" is the correct answer.

Explanation:

The Process Capability seems to be a method of measuring of how and why the framework performs concerning something like the successful objectives. This same capacity is characterized as that of the client's voice over procedure speech.Through using functionality indicators it analyses the performance with an in-control process with the permissible range.

The radial component of acceleration of a particle moving in a circular path is always:________ a. negative. b. directed towards the center of the path. c. perpendicular to the transverse component of acceleration d. all of the above

Answers

Answer:

d. all of the above

Explanation:

There are two components of acceleration for a particle moving in a circular path, radial and tangential acceleration.

The radial acceleration is given by;

[tex]a_r = \frac{V^2}{R}[/tex]

Where;

V is the velocity of the particle

R is the radius of the circular path

This radial acceleration is always directed towards the center of the path, perpendicular to the tangential acceleration and negative.

Therefore, from the given options in the question, all the options are correct.

d. all of the above

There are different type of acceleration.  The radial component of acceleration of a particle moving in a circular path is always negative, directed towards the center of the path and perpendicular to the transverse component of acceleration.

Radial acceleration is simply known as the rate of change of angular velocity where the direction is towards the center about whose circumference, the body tend to shift.

This is due to because of the centripetal force. So centripetal force is the reason for a radial acceleration.

Learn more from

https://brainly.com/question/13308560

1. Two types of superchargers include

A. turbine and piston.
B. roots-type and centrifugal.
C. double- and single-acting
D. rotary and reciprocating.

Answers

The answer is b, roots type and centrifugal.

The magnitude of the normal acceleration is
A) proportional to radius of curvature.
B) inversely proportional to radius of curvature.
C) sometimes negative.
D) zero when velocity is constant.

Answers

Answer:

b. inversely proportional to radius of curvature

Explanation:

In curvilinear motions, the normal acceleration which is also called the centripetal acceleration is always directed towards the center of the circular path of motion. This acceleration has a magnitude that is directly proportional to the square of the speed of the body undergoing the motion and inversely proportional to the radius of the curvature of the motion path. The centripetal or normal acceleration a,  can be given by;

a = [tex]\frac{v^2}{r}[/tex]

Where;

v = speed of the body

r = radius of curvature.

An AC generator supplies an rms voltage of 120 V at 50.0 Hz. It is connected in series with a 0.650 H inductor, a 4.80 μF capacitor and a 301 Ω resistor.
(a) What is the impedance of the circuit?
(b) What is the rms current through the resistor?
(c) What is the average power dissipated in the circuit?
(d) What is the peak current through the resistor?
(e) What is the peak voltage across the inductor?
(f) What is the peak voltage across the capacitor?
The generator frequency is now changed so that the circuit is in resonance. What is that new (resonance) frequency?

Answers

Answer:

Explanation:

f = 50.0 Hz, L = 0.650 H, π = 3.14

C = 4.80 μF, R = 301 Ω resistor. V = 120volts

XL = wL = 2πfL

= 2×3.14×50* 0.650

= 204.1 Ohm

Xc= 1/wC

Xc = 1/2πfC

Xc = 1/2×3.14×50×4.80μF

= 1/0.0015072

= 663.48Ohms

1. Total impedance, Z = sqrt (R^2 + (Xc-XL)^2)= √ 301^2+ (663.48Ohms - 204.1 Ohm)^2

√ 90601 + (459.38)^2

√ 90601+211029.98

√ 301630.9844

= 549.209

Z = 549.21Ohms

2. I=V/Z = 120/ 549.21Ohms =0.218Ampere

3. P=V×I = 120* 0.218 = 26.16Watt

Note that

I rms = Vrms/Xc

= 120/663.48Ohms

= 0.18086A

4. I(max) = I(rms) × √2

= 0.18086A × 1.4142

= 0.2557

= 0.256A

5. V=I(max) * XL

= 0.256A ×204.1

=52.2496

= 52.250volts

6. V=I(max) × Xc

= 0.256A × 663.48Ohms

= 169.85volts

7. Xc=XL

1/2πfC = 2πfL

1/2πfC = 2πf× 0.650

1/2×3.14×f×4.80μF = 2×3.14×f×0.650

1/6.28×f×4.8×10^-6 = 4.082f

1/0.000030144× f = 4.082×f

1 = 0.000030144×f×4.082×f

1 = 0.000123f^2

f^2 = 1/0.000123048

f^2 = 8126.922

f =√8126.922

f = 90.14 Hz

A two-lane, one-way ramp from an urban expressway with a design speed of 30 mi/h connects with a local road at a T-intersection. The turning roadway has a vertical curb on both sides. Determine the width of the turning roadway if the predominant turning vehicles are single unit trucks with some semi-trailers. Use 0.08 for super-elevation if applicable.

Answers

Answer:

30 feet

Explanation:

Given data :

design speed = 30 miles/h

super elevation = 0.08

determine the width of the turning roadway

calculate the value of R = V^2 / 15( e + p)

e = 0.08 , p = 0.2 , v = 30

R = (30)^2 / 15 ( 0.08 + 0.2 )

  = 900 / 15 ( 0.28 )

  ≈ 215 ft

pavement width from the calculation above = 28 ft

width of the turning roadway = pavement width + 2 = 30 feet ( because there are two vertical widths joining up the main road at the T junction )

A cylinder is to be cast out of aluminum. The diameter of the disk is 500 mm and its thickness is 20 mm. The mold constant 2.0 sec/mm2 in Chvorinov's formula to calculate the solidification time.

Required:
a. Calculate the minimum time (minutes) for the casting to solidify.
b. Discuss if the result in part (a) is the same when casting grey cast iron.

Answers

Answer:

a) the minimum time (minutes) for the aluminium casting to solidify is 2.86 min

b) the minimum time (minutes) for the grey iron casting to solidify is 2.13 min. Therefore solidification of grey iron cast will take less time (2.13 min) compared to the solidification of the aluminium cast (2.86 min)

Explanation:

Given that; diameter of Disk = 500 mm, thickness t = 20, mold constant Cm = 2.0 sec/mm²

first we find the volume and Area;

Volume V = πD²t / 4

Volume V = π × (500)² × 20 / 4 = 3,926,991 mm³

Area A = 2πD²/ 4 + πDt

Area A = {[π × (500)²] / 2} +{ π × (500) × (20)}

Area A = 392,699.08 + 31,415.93

Area A = 424,115 mm²

a)

Chvorinov’s rule

T(aluminium) = Cm (V/A) ²

T(aluminium) =  2.0 × (3,926,991 / 424,115) ²

T(aluminium) = 171.5 s = 2.86 min

∴ the minimum time (minutes) for the casting to solidify is 2.86 min

b)

For cast iron

Cm (mold constant = 1.488 sec/mm²)

Chvorinov’s rule

T(iron) = Cm (V/A) ²

T(iron) = 1.488 × (3,926,991 / 424,115) ²

T(iron) = 127.5720s = 2.13 min

Therefore solidification of grey iron cast will take less time (2.13 min) compared to the solidification of the aluminium cast (2.86 min)

(2x+y)dx+(x-2y)dy=0 solve the differential equation

Answers

Answer: y' = - x'

Explanation:

Let f(x) = 2x + y

then f'(x) = 2 + y'

Let f(y) = x - 2y

then f'(y) = x' - 2

Given:  f'(x) + f'(y) = 0

         2 + y' + x' - 2 = 0

                y' + x'= 0

                 y' = -x'

This can also be written as:       [tex]\dfrac{dy}{dx}=-\dfrac{d}{dx}[/tex]

The structure of a house is such that it loses heat at a rate of 5400 kJ/h per degree Cdifference between the indoors and outdoors. A heat pump that requires a power input of 6 kW isused to maintain this house at 21 C. Determine the lowest outdoor temperature for which the heatpump can meet the heating requirements of this house

Answers

Answer: Tl = - 13.3°C

the lowest outdoor temperature is - 13.3°C

Explanation:

Given that;

Temperature of Th = 21°C = 21 + 273 = 294 K

the rate at which heat lost is Qh = 5400 kJ/h°C

the power input to heat pump Wnet = 6 kw

The COP of a reversible heat pump depends on the temperature limits in the cycle only, and is determined by;

COPhp = Th/(Th - Tl)

COPhp = Qh/Wnet

Qh/Wnet = Th/(Th -Tl)

the amount of heat loss is expressed as

Qh = 5400/3600(294 - Tl)

the temperature of sink

( 5400/3600(294 - Tl)) / 6 = 294 / ( 294 - Tl)

now solving the equation

Tl = 259.7 - 273

Tl = - 13.3°C

so the lowest outdoor temperature is - 13.3°C

Which of the following sentences is
punctuated incorrectly?

Answers

Answer:

Um is there suppose to be a picture with the sentences on

Answer:

It's B I did the test and I was right on B

Explanation:

I don't know I knew it was B

Punctuate or edit the following sentences. Your punctuation and/or revisions should reflect best TW style and grammar writing practices.
1. The author an expert in cybersecurity will speak via Zoom this Wednesday.
2. Williams' book contains many illustrations, this makes it quick reading.
3. Based on the available evidence the university administrators have opted for a hybrid format for the fall quarter which begins September 20.
4. (Thesis statement) Free laptops should be offered to all students who need them.

Answers

I inferred you want literal editing of the text above.

Explanation:

Here's a correction of the sentences:

1. The author, an expert in cybersecurity will speak via Zoom on Wednesday.

In this sentence, punctuation mark ( , ) was added and the word  'this' was replaced with 'on'.

2. Williams' book contains many illustrations, which makes it easy to read.

Added punctuation and made a revision of the sentence.

3. Based on the available evidence, the university administrators have opted for a hybrid format for the fall, which begins September 20.

Mainly added punctuations to make the senstence clarer.

4. (Thesis statement) I believe Free laptops should be offered to all students who need them.

Made a few additions.

/ Air enters a 20-cm-diameter 12-m-long underwater duct at 50°C and 1 atm at a

mean velocity of 7 m/s, and is cooled by the water outside. If the average heat

transfer coefficient is 85 W/m2

°C and the tube temperature is nearly equal to the

water temperature of 5°C, determine the exit temperature of air and the rate of heat

transfer.​

Answers

Answer:

A) EXIT TEMPERATURE = 14⁰C

b) rate of heat transfer of air = - 13475.78 = - 13.5 kw

Explanation:

Given data :

diameter of duct = 20-cm = 0.2 m

length of duct = 12-m

temperature of air at inlet= 50⁰c

pressure = 1 atm

mean velocity = 7 m/s

average heat transfer coefficient = 85 w/m^2⁰c

water temperature = 5⁰c

surface temperature ( Ts) = 5⁰c

properties of air at 50⁰c and at 1 atm

= 1.092 kg/m^3

Cp = 1007 j/kg⁰c

k = 0.02735 W/m⁰c

Pr = 0.7228

v  = 1.798 * 10^-5 m^2/s

determine the exit temperature of air and the rate of heat transfer

attached below is the detailed solution

Calculate the mass flow rate

= p*Ac*Vmean

= 1.092 * 0.0314 *  7 = 0.24 kg/s

Technician A says that when the malfunction indicator light or service engine light is on you should retrieve the diagnostic trouble code and follow the manufacturers recommended procedure. Technician B says that all obd-ll monitors must have the enabled criteria achieved before a test is performed. Who is correct?

Answers

Answer:both

Explanation:

When replacing a timing belt, many experts and vehicle manufacturers recommend that all of the following should be replaced except the

A. water pump
B. camshaft oil seal(s).
C. camshalt sprocket
D. tensioner assembly

Answers

Answer:

Correct Answer:

A. water pump

Explanation:

Timing belt in a vehicle helps to ensure that crankshaft, pistons and valves operate together in proper sequence. Timing belts are lighter, quieter and more efficient than chains that was previously used in vehicles.

Most car manufacturers recommended that, when replacing timing belt, tension assembly, water pump, camshaft oil seal should also be replaced with it at same time.

B1) 20 pts. The thickness of each of the two sheets to be resistance spot welded is 3.5 mm. It is desired to form a weld nugget that is 5.5 mm in diameter and 5.0 mm thick after 0.3 sec welding time. The unit melting energy for a certain sheet metal is 9.5 J/mm3 . The electrical resistance between the surfaces is 140 micro ohms, and only one third of the electrical energy generated will be used to form the weld nugget (the rest being dissipated), determine the minimum current level required.

Answers

Answer:

minimum current level required =  8975.95 amperes

Explanation:

Given data:

diameter = 5.5 mm

length = 5.0 mm

T = 0.3

unit melting energy = 9.5 j/mm^3

electrical resistance = 140 micro ohms

thickness of each of the two sheets = 3.5mm

Determine the minimum current level required

first we calculate the volume of the weld nugget

v = [tex]\frac{\pi }{4} * D^2 * l[/tex] = [tex]\frac{\pi }{4} * 5.5^2 * 5[/tex] = 118.73 mm^3

next calculate the required melting energy

= volume of weld nugget * unit melting energy

= 118.73 * 9.5 = 1127.94 joules

next find the actual required electric energy

= required melting energy / efficiency

= 1127 .94 / ( 1/3 )  = 3383.84 J

TO DETERMINE THE CURRENT LEVEL REQUIRED  use the relation below

electrical energy =  I^2 * R * T

3383.84 / R*T = I^2

3383.84 / (( 140 * 10^-6 ) * 0.3 ) = I^2

therefore  8975.95 = I ( current )

A plate is supported by a ball-and-socket joint at A, a roller joint at B, and a cable at C. How many unknown support reactions are there in this problem?

Answers

Answer:

There are five (5) unknown support reactions in this problem.

Explanation:

A roller joint rotates and translates along the surface on which the roller rests. The resulting reaction force is always a single force that is perpendicular to, and away from, the surface. This allows the roller to move in a single plane along the surface where it rests.

A cable support provides support in one direction, parallel, and in opposite direction to the load on it. There exists a single reaction from the cable pointed upwards.

A ball-and-socket joint have  reaction forces in all 3 cardinal  directions. This allows it to move in the x-y-z plane.

The total unknown reactions on the member are five in number.

A fixed mass of saturated water vapor at 400 kpa is isothermally cooled until it is a saturated liquid. Calculate the amount of heat rejected during this process in kJ/kg.

Answers

This is the explanation

The amount of heat rejected during the process in kJ/kg is 2133.4 kJ/kg.

What is heat?

Heat is defined as the process of kinetic energy being transferred from an energy source to a medium or an item. These three mechanisms radiation, conduction, and convection can all transmit energy. These three modes of heat transfer are typically combined, and it often happens on its own. The heat energy can be transformed into other types of energy, such as mechanical and kinetic energy. Thermal (heat) energy is a type of energy that is produced by the movement of particles and is a component of all matter.

The process rejects a certain amount of heat, which is

-q = w + Δu

q = - w - Δu

q = - 185.5 kJ/kg - 1948.9 kJ/kg

q = 2133.4 kJ/kg

Thus, the amount of heat rejected during the process in kJ/kg is 2133.4 kJ/kg.

To learn more about heat, refer to the link below:

https://brainly.com/question/1429452

#SPJ2

how to build a laser pointer?

Answers

Answer:

It's easier to buy one, but you can search for a tutorial on how to make one on Yuotube.

There are quite a few videos on how to make one.

The phase sequence of a 3-phase system for which VAN = 120 /90o V and VBN = 120 /210o V is:_______
a) bca
b) abc
c) cab
d) acb

Answers

Answer:

b. abc

Explanation:

The phase rotation and its sequence is order in which voltage is reached to their respective sources. The wave forms of a polyphase flow through AC source to the panel. The three phase system has two possible sequence which can be a-b-c or c-b-a. The correct answer is therefore b.

"The transistor base-emitter voltage (VBE) a. increases with an increase in temperature. b. is not affected by temperature change. c. decreases with an increase in temperature. d. has no effect on collector current."

Answers

Answer:

C) Decreases with an increase in temperature

Explanation:

As the temperature of a transistor increases, the thermal runaway property of the transistor becomes more significant and the transistors, conducting more freely as a result of the rise in temperature, causes an increase in the collector current or leakage current. The transistor base-emitter voltage decreases as a result.

With increased heating due to heavy current flow, the transistor is damaged.

A charge is distributed uniformly along a long straight wire. The electric field 2 cm from the wire is 36 N/C. The electric field 4 cm from the wire is:

Answers

Answer:

New electric field = 18 N/C

Explanation:

Given:

Length (E1) = 2 cm

New length (E2) = 4 cm

Electric field =  36 N/C

Find:

New electric field

Computation:

New electric field = 36 [2 / 4]

New electric field = 36 [1/2]

New electric field = 18 N/C

Other Questions
What is the FIRST major step of the writing process? The data set {3, 7, 5, 4, 1} consists of the lengths, in minutes, of a sample of speeches at an awards banquet. Use a formula to find the standard deviation of the sample, and label it with the correct variable. 9) Selected information regarding a company's most recent quarter follows (all data in thousands). 9) _______ Direct labor $540 Beginning work in process inventory $330 Ending work in process inventory $420 Cost of goods manufactured $1620 Manufacturing overhead $830 What was the cost of direct materials used for the quarter These cones are similar. Find the volumeof the smaller cone. Round to thenearest tenth. Gabriel Industries stock has a beta of 1.12. The company just paid a dividend of $1.15, and the dividends are expected to grow at 4 percent. The expected return on the market is 11.4 percent, and Treasury bills are yielding 3.8 percent. The most recent stock price is $85. (a) Calculate the cost of equity using the dividend growth model method. (b) Calculate the cost of equity using the SML method. (c) Why do you think your estimates in (a) and (b) are so different? Please help and explain so I can understand for future questions Complete the table for the given rule.Rule: y = 6x 4. Y1310 Over the next century, how do you think the effects of global climate change will compare for species adapted to extreme heat (tropical and hot desert species) versus those adapted to extreme cold (polar species) A customer buys 1,000 shares of XYZ at $60 in a margin account, regular way settlement. Two days after the trade, XYZ has dropped to $40. The minimum maintenance margin requirement is: What is the first step in mathematical induction? Explain why human being is regarded as a complex machine. Why does anaerobic respiration produce less energy than aerobic respiration?A. Glucose is only partially broken down.B. The process takes a lot of energy, and uses most of what it releases from Glucose.C. Glucose can't be broken down without oxygen, so the body's other energy source,lipids are used.D. Glucose can't be used, so there is only ATP. Which of the following is a solution of y > |x| - 6? A(-1, -5) B(-5, 1) C(5, -1) Input a list of positive numbers, find the mean (average) of the numbers, and output the result. Use a subprogram to input the numbers, a function to find the mean, and a subprogram to output the result. Use a subprogram to Input the numbers, a Function to find the mean and a subprogram to output the Result. Tan - cosec sec (1-2 cos) = cot around 2.232 to the nearest hundredth What is the maximum wavelength of incident light for which photoelectrons will be released from gallium The production budget shows expected unit sales of 40000. Beginning finished goods units are 3800. Required production units are 41600. What are the desired ending finished goods units How did the foreign relations scandal known as the XYZ Affair affect politics in the United States? a proposed new project has projected sales of $222000, costs of $96500, and deperciation of $26100. The tax rate is 24 percent.Calculate operating cash flow using the four different approaches.