Answer:
Umm.... because the spit that comes up of your mouth when you talk mixes with the air
Explanation:
4. The process of heating milk to kill microorganisms that cause spoilage and disease without affecting its nutritional value is called
A. Homogenization
B. Pasteurization
C. Boiling
D. Poaching
Answer:
I think the answer is C. Boiling but I'm not 100% sure.
A wedge would be best described as
A wheel and axle used to cTeate a rotary motion
A lever arm fixed to a shaft
A triangle shaped tool that functions as an inclined plane
A rectangular shaped tool that functions as a pulley
Answer:
A rectangular shaped tool that functions as a pulley.
Explanation:
i beleive
Determine the size of memory needed for CD recording of a piece of music, which lasts for 26 minutes, is done with a 20-bit Analog-to-Digital Converter (ADC) in stereo (2 channels), at the rate of 44.1 kSa/s, with the compression factor 6 (allow 10% error margin).
Answer: the size of memory needed for the CD recording is 28.7 MB
Explanation:
so in the case of stereo, the bitrate is;
⇒ 26 × 60 × 44.1 × 10³ × 2
= 137592 × 10³
for 10 bit
⇒ 137592 × 10³ × 10
= 1375920 × 10³ bits
now divide by 8 (convert to bytes)
⇒ (1375920 × 10³) / 8
= 171,990,000 BYTE
divide by 1000 (convert to kilobytes)
= 171,990,000 / 1000
= 171,990 KILOBYTES
now Given that, the compression ratio is 6
so
171,990 / 6
= 28665 KB
we know that. 1 MB = 1000 KB
x MB = 28665 KB
x MB = 28665 / 1000
⇒ 28.665 MB ≈ 28.7 MB
Therefore the size of memory needed for the CD recording is 28.7 MB
The purpose of pasteurizing milk is to A. Kill pathogens B. Break down milk fat C. Add vitamins and minerals D. Prevent spoilage by sunlight
Answer:
The answer is A
Explanation:
The correct answer is A
a cantilever beam 1.5m long has a square box cross section with the outer width and height being 100mm and a wall thickness of 8mm. the beam carries a uniform load of 6.5kN/m along the entire length and, in the same direction, a concentrated force of 4kN at the free end. (a) determine the max bending stress (b) determine the max transervse shear stress (c) determine the max shear stress in the beam
Answer:
a) 159.07 MPa
b) 10.45 MPa
c) 79.535 MPa
Explanation:
Given data :
length of cantilever beam = 1.5m
outer width and height = 100 mm
wall thickness = 8mm
uniform load carried by beam along entire length= 6.5 kN/m
concentrated force at free end = 4kN
first we determine these values :
Mmax = ( 6.5 *(1.5) * (1.5/2) + 4 * 1.5 ) = 13312.5 N.m
Vmax = ( 6.5 * (1.5) + 4 ) = 13750 N
A) determine max bending stress
б = [tex]\frac{MC}{I}[/tex] = [tex]\frac{13312.5 ( 0.112)}{1/12(0.1^4-0.084^4)}[/tex] = 159.07 MPa
B) Determine max transverse shear stress
attached below
ζ = 10.45 MPa
C) Determine max shear stress in the beam
This occurs at the top of the beam or at the centroidal axis
hence max stress in the beam = 159.07 / 2 = 79.535 MPa
attached below is the remaining solution
Five identical keys are suspended from a balance, which is held horizontally as shown. The two keys on the left are attached to the balance 6 cm from the pivot and the three keys on the right are attached 5 cm from the pivot. What will happen when the person lets go of the balance beam?
Answer:
movement in clockwise direction.
Explanation:
The following parameters or information are given from the question above, they are:
[1]. There are two identical keys, [2]. two out of the five keys are attached to 6cm from the pivot, [3]. three keys out of the five keys on the right are attached 5 cm.
Therefore, considering the moment of force, the two keys on the left = 2 × 6 = 12.
Also, considering the moment of force, the 3 keys on the right = 3 × 5 = 15.
Therefore, we have more weight on the right keys. So, in order to balance the force there must be movement in clockwise direction.
