The change in enthalpy of an incompressible substance with a density of 1000 kg/m³ that is isothermally compressed from 100 to 1000 kPa is 0 kJ/kg.
What is enthalpy?Enthalpy is a measure of the total energy of a thermodynamic system. In addition, it incorporates the energy that is supplied to the system as heat, as well as any energy that is used as work. Enthalpy is represented by the symbol H and is usually calculated in units of joules (J).
What is an incompressible substance?An incompressible substance is one that cannot be compressed or compressed to a significant degree. Liquids are examples of such materials. They are often described as having a constant density because, unlike gases, they do not easily change in volume in response to pressure or temperature changes. Therefore, the change in enthalpy is 0 kJ/kg.
Learn more about Enthalpy here: https://brainly.com/question/16985375.
#SPJ11
a solid plastic cylinder of radius 2.33 cm and length 6.30 cm. find the net charge of this cylinder, in nc (nanocoulombs), if it carries a uniform volumetric charge density of 540 nc/m3 throughout the whole volume of the plastic.
The net charge of a solid plastic cylinder of radius 2.33 cm and length 6.30 cm, carrying a uniform volumetric charge density of 540 nc/m3, is equal to 0.0583 nC (nanocoulombs)
To determine the net charge of a cylinder, the formula Q =ρV has to be used where Q is the net charge, ρ is the uniform volumetric charge density, and V is the volume of the cylinder.
ρ is given as 540 nc/m³.
V is calculated using the formula
V = πr²h
where r is the radius and h is the length.
π is approximated to be 3.14.
h is given as 6.30cm
r is 2.33cm
so the calculation for V becomes;
V = πr²h
V = 3.14 x 2.33² x 6.3
V = 108.02 cm³ or 108.02 x 10⁻⁶ m³.
Substitute the values of Q and V into the equation and solve for Q:
Q = ρVQ = 540 nc/m³ x 108.02 x 10⁻⁶ m³
Q = 0.0583 nc (to 3 decimal places)
Therefore the net charge of this cylinder, in nc (nanocoulombs) is 0.0583nc.
Learn more about net charge at https://brainly.com/question/26036371
#SPJ11
what device is used to shunt transient current to ground in the event of an indirect lightning strike?
In the event of an indirect lightning strike, a Surge Protection Device (SPD) is used for shunting transient current to the ground. An SPD is a protective device that limits the voltage supplied to an electrical system by either blocking or shorting to ground any unwanted voltages above a safe threshold. This can help protect against damage from transient current, a short, high-energy burst of electricity.
A surge protector is an electrical device that protects electronic devices from power surges and other electrical disturbances. The device will shield the equipment that is plugged into it from the spikes that are present in an electrical supply.The term “surge protector” is frequently used in reference to a category of products that is also known as a “transient voltage suppressor.” This name provides insight into how these devices work. They suppress transient voltage, which is a sudden surge of voltage that is brief in nature
.How do surge protectors work?
Surge protectors work by preventing transient voltage spikes from reaching sensitive electrical equipment. These devices typically consist of a metal oxide varistor, which is a component that is used to divert any unwanted voltage away from sensitive electronics and toward a grounded element.The varistor is connected to a metal oxide varistor, which is responsible for conducting the unwanted voltage away from the equipment and toward the ground. Surge protectors will reduce voltage to a safe level by grounding the unwanted voltage. Surge protectors are used to protecting a wide range of electronic devices, including computers, audio equipment, and video equipment.
For more details go through the link: https://brainly.com/question/30869810
#SPJ11
Transient current refers to an electrical current that flows for a brief period. Transient currents are caused by temporary changes in voltage, such as those caused by electrical discharges, power outages, and other events. Surge currents are another name for transient currents, and they are often used interchangeably.
A lightning strike is an electrical discharge from the atmosphere to the earth's surface. Thunderstorms, which are associated with lightning, are the most frequent natural cause of the electrical discharge. A lightning bolt can produce extremely high voltages and currents, posing a significant threat to electrical systems and the people who operate them.
A surge protector is a device that is intended to protect electrical devices from voltage spikes, surges, and other power fluctuations. Surge protectors work by shunting transient currents to the ground in the event of an indirect lightning strike. They can also be used to safeguard against other types of power surges, such as those caused by power outages, grid switching, and other issues. Surge protectors are often utilized in industrial and commercial settings, as well as in homes.
For more information regarding this topic, you can click the below link
https://brainly.com/question/1100341
#SPJ11
In outer space will a liquid in a beaker exert a pressure on the bottom or on the sides of a beaker?
Answer:
Yo dude, if you had a beaker of liquid in outer space, it wouldn't push down on the bottom or the sides of the beaker like it would on Earth. In space, there's no gravity to make the liquid settle down, so it forms a round shape because of surface tension. So basically, the liquid would just float around in a ball inside the beaker. If you moved the beaker around, the liquid would just roll around with it like a bouncy ball.
When a ball bounces against a wall there will be large change in velocity in short period of time. This means the ____ is large, hence the net ___ must be proportionately large as well.
A change in velocity in short period of time means the acceleration is large, hence the net force must be proportionately large as well.
What is a force?A force is a physical quantity that induces a body to undergo an alteration in speed, direction of motion, or shape. A force can be classified as a push or a pull. When forces are equal, the forces are balanced and the object is not moving. Otherwise, if the forces are not equal, making it unbalanced will not give the object any movement.
The force that induces the change in the speed or direction of an object is referred to as a net force. The net force is equal to the product of the mass of the object and its acceleration. Newton (N) is the unit of measurement for force.
When a ball bounces against a wall, there will be a large change in velocity in a short period of time. This means the acceleration is large, hence the net force must be proportionately large as well.
Learn more about acceleration here: https://brainly.com/question/26408808
#SPJ11
A sandbag is dropped from a balloon which is ascending vertically at a constant speed of 6 m/s.
If the bag is released with the same upward velocity of 6 m/s when t = 0 and hits the ground when t = 8 s, determine the speed of the bag as it hits the ground and the altitude of the balloon at this instant.
The speed of the bag as it hits the ground is -47.2 m/s and the altitude of the balloon at this instant is 245.6 m.
At t = 0, the sandbag is released with an upward velocity of 6 m/s. Since the balloon is ascending vertically at a constant speed of 6 m/s, the sandbag will be accelerating downwards due to the force of gravity.
Using the equation of motion v = u + at, we can calculate the speed of the sandbag at the time it hits the ground (t = 8 s). We can calculate the velocity by substituting u = 6 m/s, a = -9.8 m/s2 (acceleration due to gravity), and t = 8 s. This gives us a velocity of -47.2 m/s.
At the instant the sandbag hits the ground, the altitude of the balloon can be calculated using the equation s = ut + 1/2at2. We can calculate the altitude by substituting u = 6 m/s, a = -9.8 m/s2, and t = 8 s. This gives us an altitude of 245.6 m.
Therefore, the speed of the bag as it hits the ground is -47.2 m/s and the altitude of the balloon at this instant is 245.6 m.
To learn more about speed follow
https://brainly.com/question/14691279
#SPJ11
The straight section of the line in figure 10 can be used to calculate the useful power output of the kettle explain how
Using the line's straight segment in figure 10, it is possible to determine the usable power output of the kettle.
The period that the kettle is heating the water up until it reaches boiling point is depicted by the straight segment of the line in figure 10. Both the power input to the kettle and the rate of energy transfer to the water remain constant throughout this period. Hence, by dividing the energy that was transmitted to the water during this period by the whole amount of time, the usable power output of the kettle can be determined. The straight section's slope, which reflects the rate of energy transfer, and horizontal distance, which indicates the elapsed time, may be used to calculate this. The energy transmitted is calculated by dividing the rate of energy transmission by the amount of time.
learn more about power here:
https://brainly.com/question/22285866
#SPJ4
the maximum energy of photoelectrons from aluminium is 2.3 ev for radiation of 2000 a and 0.90 ev for radiation of 3130 a. use this data to calculate plancks constant and the work function of aluminium
The maximum energy of photoelectrons from aluminium is 2.3 eV for radiation of 2000 Å and 0.90 eV for radiation of 3130 Å.
To calculate Planck's constant and the work function of aluminium, we need to use the equation:
h = E2 - E1/ λ2 - λ1
Where h is Planck's constant, E1 and E2 are the maximum energy of photoelectrons for each wavelength, and λ1 and λ2 are the wavelengths.
Using the given data, we have:
h = (2.3 - 0.90) / (2000 - 3130)
Therefore, h = -1.4 eV / -930 Å, which simplifies to h = 0.0015 eVÅ.
The work function of aluminium is equal to the maximum energy of the photoelectrons for the longest wavelength, in this case, 0.90 eV. Therefore, the work function of aluminium is 0.90 eV.
Learn more about photoelectrons at brainly.com/question/16772624
#SPJ11
which of the following includes all common types of radioactive decay? a. atomic number, beta particle emission, electron capture B. alpha particle emission, beta particle emission, half-life C. alpha particle emission, beta particle emission, radioactive parent isotope D. alpha particle emission, beta particle emission, electron capture E. alpha particle emission, stable daughter, electron capture
Alpha particle emission, beta particle emission, and electron capture are all common types of radioactive decay.The correct answer is D.
They are common types of radioactive decay's because:
Alpha particle emission involves the emission of an alpha particle (a helium nucleus) from the nucleus of an atom. This reduces the atomic number by 2 and the mass number by 4.Beta particle emission involves the emission of a beta particle (an electron or a positron) from the nucleus of an atom. This changes a neutron to a proton or a proton to a neutron, respectively, and may increase or decrease the atomic number by 1.Electron capture involves the capture of an electron by the nucleus of an atom, which changes a proton to a neutron and decreases the atomic number by 1.Option D includes all of these types of radioactive decay (alpha particle emission, beta particle emission, and electron capture), so it is the correct answer
To learn more about radioactive decay:
https://brainly.com/question/11117468
#SPJ11
Complete the following sentence.
A diameter is also a...
Answer:
A diameter is also a double of radius
When the price of radios decreases 5%, quantity demanded increases 5%. The price elasticity of demand for radios is ________ and total revenue from radio sales will ________.
Price elasticity of demand for radios is 1 and total revenue from radio sales will remain constant.
Price elasticity of demand is calculated as the percentage change in quantity demanded divided by the percentage change in price. Using this formula, we can calculate the price elasticity of demand for radios as follows:
Price elasticity of demand = (percentage change in quantity demanded) / (percentage change in price)
Given that when the price of radios decreases by 5%, quantity demanded increases by 5%.So, the percentage change in quantity demanded = 5% and the percentage change in price = -5%. (Because price has decreased by 5%.)Price elasticity of demand = (5% / -5%) = -1.The negative sign indicates that the demand is elastic. However, the question asks for a positive value, so we take the absolute value of -1.Price elasticity of demand = 1.
Therefore, the price elasticity of demand for radios is 1.When the price elasticity of demand is equal to 1, it means that the demand is unit elastic. This implies that the percentage change in quantity demanded is equal to the percentage change in price. If the price of radios decreases by 5% and the quantity demanded increases by 5%, it means that the total revenue from radio sales will remain constant. In other words, the increase in quantity demanded is exactly offset by the decrease in price, resulting in the same total revenue.
More price elasticity: https://brainly.com/question/22716533
#SPJ11
Which of the following is an example of potential energy?A .A vibrating pendulum at its maximum displacement from its mean positionB. A body at rest from some height from the ground.C. A wound clock spring.D. A vibrating pendulum when it is just passing through its mean position
The best example that shows the potential energy is a body at rest from some height from the ground, thus the correct answer is option b.
Potential energy is defined as the energy stored by an object or system in a position that can contribute to doing work when released. It is the stored energy of an object or system.
In this case, the body at rest has potential energy because of its height above the ground. As it falls, the potential energy is converted to kinetic energy.
Option A describes kinetic energy as the vibrating pendulum at its maximum displacement, and option D describes a momentary state of rest in a pendulum's motion, which does not involve potential energy. Option C describes the potential energy stored in a wound clock spring, but it possesses elastic potential energy.
Thus, the body at rest has potential energy because of its height above the ground. Thus, option b is correct.
Learn more about Potential energy here:
https://brainly.com/question/14427111
#SPJ11
You are the process engineer at Corvallis Automobiles Inc., and you have received an order to turn a cylindrical bar on an engine lathe to the dimensions specified in Fig. 1. For this order you will use cylindrical bar stock that is 48-inches long and 4-inches in diameter. The 48-inch length bar will be chucked in the lathe and supported at the opposite end using a live center. You are planning to complete the operation in one pass using a cutting speed of 400 ft./min. and a feed of 0.010 in./rev. Determine the following: a) The required depth of cut (in inches) b) The material removal rate (in cubic inches per minute)
c) The time required to complete the cutting pass (in minutes)
a. the depth of cut is 0.625 inches.
b. the material removal rate is 0.003125 cubic inches per minute.
c. the time required to complete the cutting pass is 20 minutes.
How do we calculate?a) The required depth of cut can be determined by :
DOC = (4 in - 2.75 in)/2 = 0.625 in
Therefore, the depth of cut is 0.625 inches.
b) The material removal rate can be found by applying:
MRR = DOC x Width of cut x Feed rate
assuming we are using a standard carbide insert tool with a width of cut of 0.5 inches.
MRR = 0.625 in x 0.5 in x 0.010 in/rev = 0.003125 cubic inches per minute
c) The time required to complete the cutting pass is determined by:
Time = Length of cut / (Cutting speed x Width of cut x Feed rate)
Time = 48 in / (400 ft/min x (0.5 in) x (0.010 in/rev) x (1/12 ft/in)) = 20 minutes
Learn more about material removal rate at: https://brainly.com/question/13106351
#SPJ1
Acceleration due to gravity is 9.8 m/s2 on the surface of Earth, and at orbits 200 miles above the surface of Earth, where the space shuttle orbits, the acceleration is
Acceleration due to gravity is 9.8 m/s2 on the surface of Earth, and at orbits 200 miles above the surface of Earth, where the space shuttle orbits, the acceleration is 8.78 m/s².
What is gravitational force?The reason for this difference in acceleration is that the gravitational force on an object is inversely proportional to the square of the distance between them.
Thus, the further an object is from the Earth's surface, the weaker the gravitational force acting on it. This is why objects in orbit around the Earth experience less acceleration due to gravity than objects on the surface of the Earth.
To know more about gravitational force:
https://brainly.com/question/3009841
#SPJ11
at what angle above the horizon is the sun when light reflecting off a smooth lake is polarized most strongly?
The sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.
When unpolarized light reflects off a smooth surface, such as a lake, it becomes polarized in a direction perpendicular to the surface. The angle at which this polarization is strongest is known as the Brewster angle, and can be calculated using the formula:
θB = arctan(n2/n1)
where θB is the Brewster angle, n1 is the index of refraction of the medium the light is coming from, and n2 is the index of refraction of the medium the light is entering.
For water, the index of refraction is approximately 1.33, and for air it is approximately 1.00. Plugging these values into the formula, we get:
θB = arctan(1.33/1.00) = 53.1 degrees
However, this is the angle at which the light is reflected off the surface in a direction perpendicular to the surface. To find the angle above the horizon at which the light is polarized most strongly, we need to subtract 90 degrees from the Brewster angle:
37 degrees = 90 degrees - 53.1 degrees
Therefore, the sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.
For more similar questions on Brewster angle:
brainly.com/question/29428422
#SPJ11
two cars approach an ice-covered intersection. one car, of mass 1.27 103 kg, is initially traveling north at 11.6 m/s. the other car, of mass 1.70 103 kg, is initially traveling east at 11.6 m/s. the cars reach the intersection at the same instant, collide, and move off coupled together. find the velocity of the center of mass of the two-car system just after the collision.
The center of mass of the two-car system can be found by taking the weighted average of the velocities of the two cars.
The velocity of the center of mass is the average of the two cars' velocities, weighted by their masses. The velocity of the center of mass is:
Velocity of Center of Mass = (1.27 x 103 kg x 11.6 m/s + 1.70 x 103 kg x 11.6 m/s) / (1.27 x 103 kg + 1.70 x 103 kg) = 11.60 m/s.
Read more about the topic velocity:
https://brainly.com/question/80295?source=archive
#SPJ11
A resistor is constructed by shaping a material of resistivity p into a hollow cylinder of length L and with inner and outer radii ra and rb, respectively (Fig. P27.66). In use, the application of a potential difference between the ends of the cylinder produces a current parallel to the axis, (a) Find a general expression for the resistance of such a device in terms of L, p, ra, and rb. (b) Obtain a numerical value for. R when L = 4.00 cm, ra = 0.500 cm, rb = 1.20 cm, and p = 3.50 times 105 Ohm m. (c) Now suppose that the potential difference is applied between the inner and outer surfaces so that the resulting current flows radially outward. Find a general expression for the resistance of the device in terms of L, p, Figure P27.66 ra, and rb. (d) Calculate the value of R, using the parameter values given in part (b).
Explanation:
Refer to pic...........
when a 2.75-kg fan, having blades 18.5 cm long, is turned off, its angular speed decreases uniformly from 10.0 rad/s to 6.30 rad/s in 5.00 s. (a) what is the magnitude of the angular acceleration of the fan?
The angular acceleration of the fan is 0.740 rad/s^2,
Angular acceleration which represents the rate at which the angular velocity changes over time. The unit used to measure angular acceleration is radians per square second (rad/s2), according to the International System of Units. The Greek alphabet symbol alpha (α) is used to denote angular acceleration.
To calculate the angular acceleration of the fan, the formula α = Δω/Δt is used. Here, α represents angular acceleration, Δω represents the change in angular speed, and Δt represents the change in time.
In this scenario, Δω is equal to 10.0 - 6.30 = 3.70 rad/s, and Δt is equal to 5.00 s. By substituting these values into the formula, we obtain α = 3.70/5.00 = 0.740 rad/s^2.
To gain more knowledge about angular acceleration, refer to brainly.com/question/21278452.
#SPJ11
Running on a treadmill is slightly easier than running outside because there is no drag force to work against. Suppose a 60 kg runner completes a 5.0 km race in 22 minutes. Determine the drag force on the runner during the race. Suppose that the cross section area of the runner is 0.72 m2 and the density of air is 1.2 kg/m3.I know how to get the drag force, but have no idea how to get the drag coefficient, in order to plug into the equation! I found the velocity in m/s, then went to find the force using F=1/2(density of air)(velocity^2)(drag coefficient)(cross section area) but don't know what to use for the drag coefficient.
Running on a treadmill is slightly easier than running outside because there is no drag force to work against. Suppose a 60 kg runner completes a 5.0 km race in 22 minutes. The drag force on the runner during the race is 13.4 N.
Running on a treadmill is slightly easier than running outside because there is no drag force to work against. Drag force is a form of air resistance that acts on objects moving through air. When a runner is running on a treadmill, there is no drag force to work against.
In order to calculate the drag force on the runner during the race, we need to determine the drag coefficient. The drag coefficient is a dimensionless number that represents the ratio of drag force to dynamic pressure. It is affected by the shape and size of the object as well as the fluid (air) it is moving through. Generally, a higher drag coefficient means that more force is required to move the object.
To calculate the drag coefficient, we can use the following formula: Cd = Fd / (1/2 * ρ * v2 * A), where Fd is the drag force, ρ is the density of the air, v is the velocity of the object, and A is the cross-sectional area of the object.
For our example, we are given a runner that is 60 kg and completed a 5 km race in 22 minutes. The velocity of the runner can be calculated by v = d/t, where d is the distance traveled and t is the time taken. This gives us a velocity of 8.3 m/s. The density of the air is given to be 1.2 kg/m3 and the cross-sectional area is 0.72 m2.
Plugging these values into the formula gives us a drag coefficient of 0.385. This means that for every 1 unit of dynamic pressure, the drag force is 0.385. We can now calculate the drag force on the runner by multiplying the drag coefficient by 1/2 * ρ * v2 * A. In this case, the drag force is 13.4 N.
In conclusion, the drag force on the runner during the race is 13.4 N. This was calculated by determining the drag coefficient using the formula Cd = Fd / (1/2 * ρ * v2 * A) and then multiplying it by 1/2 * ρ * v2 * A.
For more such questions on Drag force.
https://brainly.com/question/12774964#
#SPJ11
a bar magnet falls under the influence of gravity along the axis of a long copper tube. if air resistance is negligible, will there be a force to oppose the descent of the magnet? if so, will the magnet reach a terminal velocity? explain.
A bar magnet falls under the influence of gravity along the axis of a long copper tube. If air resistance is negligible, there will be a force to oppose the descent of the magnet. The magnet will reach a terminal velocity. Here's why:
If the magnet falls down a copper tube under the influence of gravity, it generates an electric current that opposes the magnetic field that was created. As a result, a magnetic force is created, which opposes the fall of the magnet. As a result, there is a force opposing the descent of the magnet.The magnet will reach a terminal velocity due to the drag created by the copper tube.
As the magnet falls, it encounters the resistive forces of the copper tube, causing it to slow down. As the speed decreases, the resistive forces decrease until the drag force is equivalent to the force of gravity. The magnet then reaches a steady state called the terminal velocity. This is a state in which the magnet continues to fall, but at a steady pace since the resistive forces are balanced by the gravitational forces.
Learn more about magnetic force: https://brainly.com/question/29252577
#SPJ11
A horizontal force of magnitude 35.0N pushes a block of mass 4.00kg across a floor where the coefficient of kinetic friction is 0.600. (a) how much work is done by the applied force on the block-floor system when the block slides through a displacement of 3.00m across the floor? (b) during that displacement the thermal energy if the block increases by 40.0J. what is the increase in thermal energy of the floor? (c) what is the increase in the kinetic energy of the block?
Answer to following (a) , (b) and (c) question are: 63.00 J, 40.0 J, 63.00 J
(a) The work done by the applied force on the block-floor system when the block slides through a displacement of 3.00m across the floor can be calculated by multiplying the applied force (35.0 N) and the displacement (3.00 m), with a coefficient of kinetic friction (0.600) for the system. Thus, the work done is 35.0N * 3.00m * 0.600 = 63.00 J.
(b) The increase in the thermal energy of the floor during the displacement of 3.00m is equal to the thermal energy of the block (40.0 J), since the total thermal energy of the block-floor system remains constant. Therefore, the increase in thermal energy of the floor is 40.0 J.
(c) The increase in the kinetic energy of the block is equal to the work done by the applied force, i.e., 63.00 J.
To know more about "coefficient of kinetic friction" refer here:
https://brainly.com/question/13754413#
#SPJ11
determine whether each geologic feature is being caused by tensional, compressional, or shear stresses by analyzing the directions of the forces being applied.
In any case, the type of force that is responsible for creating a particular geological feature depends on the direction and magnitude of the forces that are acting on it.
Geological features are landforms that are made up of natural formations. A wide variety of geological features exist in nature, including mountains, valleys, canyons, caves, and others.
There are a variety of geological features that can be created as a result of tensional, compressional, or shear stresses.
Let's take a closer look at each type of stress:
Tensional: Tensional forces act to pull rocks apart. This can result in the formation of fault-block mountains, valleys, and rifts.
Compressional: Compressional forces act to push rocks together. This can lead to the creation of mountain ranges, folded mountains, and plateaus.
Shear Stresses: Shear stresses act to twist or bend rocks. This can result in the formation of faults, folds, and other geological features.
The forces that create geological features are typically produced by the movement of tectonic plates beneath the earth's surface.
When two tectonic plates come together, they can create compressional forces. When they move apart, they can create tensional forces.
When they slide past each other, they can create shear stresses. Other forces can also play a role, such as erosion or the buildup of sediment over time.
To know more about Geological features:https://brainly.com/question/19925491
#SPJ11
how many electrons are there in a 30.0 cm length of 12-gauge copper wire (diameter 2.05 mm )? express your answer using two significant figures.
There are 7.86 x 10²³ electrons in a 30.0 cm length of 12-gauge copper wire with a diameter of 2.05 mm.
To calculate the number of electrons in a 30.0 cm length of 12-gauge copper wire (diameter 2.05 mm), you can use the following equation:
n = ρV / m
where:
n is the number of electrons.ρ is the density of copper (8.96 g/cm³).V is the volume of the wire. m is the mass of one copper atom.To find the volume of the wire, you need to use the equation for the volume of a cylinder:
V = πr²hWhere:
r is the radius of the wire (1.025 mm). h is the length of the wire (30.0 cm).Therefore, V = π(1.025 mm)²(30.0 cm) = 9.30 cm³The mass of one copper atom is 63.55 g/mol or 1.054 x 10⁻²² g. To find m, you need to use Avogadro's number (6.02 x 10^23 atoms/mol):m = (63.55 g/mol) / (6.02 x 10^23 atoms/mol) = 1.055 x 10⁻²² g
Now, you can plug in the values:
n = (8.96 g/cm³)(9.30 cm³) / (1.055 x 10⁻²² g) = 7.86 x 10²³ electrons
Therefore, there are 7.86 x 10²³ electrons in a 30.0 cm length of 12-gauge copper wire with a diameter of 2.05 mm. This should be rounded to 2 significant figures, so the final answer is 7.9 x 10²³ electrons.
Learn more about electrons: https://brainly.com/question/26084288
#SPJ11
Physics Help Requested Suppose our experimenter repeats his experiment on a planet more massive than Earth, where the acceleration due to gravity is g=30 m/s2. When he releases the ball from chin height without giving it a push, how will the ball's behavior differ from its behavior on Earth? Ignore friction and air resistance. (Select all that apply.)a. It will take more time to return to the point from which it was released.b. It will smash his face. Its mass will be greater.c. It will take less time to return to the point from which it was released. d, It will stop well short of his face.
On a planet with more massive gravity, such as [tex]g = 30 \ m/s^2[/tex], the ball released from chin height will take less time to return to the point from which it was released, due to the increased acceleration due to gravity.
It will take less time to return to the point from which it was released. The acceleration due to gravity is much stronger on this planet, so the ball will accelerate faster as it falls toward the ground. This means that it will reach its lowest point more quickly and then rise back up to its starting point more quickly as well.
Also, the mass of the ball is not affected by the strength of the gravitational acceleration on the planet.
Learn more about acceleration:
https://brainly.com/question/460763
#SPJ11
a 0.400 kg mass hangs from a string with a length of 0.9 m, forming a conical pendulum. the period of the pendulum in a perfect circle is 1.4 s. what is the angle of the pendulum?
A 0.400 kg mass hangs from a string with a length of 0.9 m, forming a conical pendulum. the period of the pendulum in a perfect circle is 1.4 s then the angle of pendulum is 14.68°.
Given:
Mass of the object = 0.4kg
Length of string = 0.9m
Period of conical pendulum = 1.4s
The angle of pendulum is calculated by using this formula :
T = 2π(r/g)1/2
where, T is the time period of the circular motion g is acceleration due to gravity r is radius of the circle
Let us assume, Angle made by the string with the vertical axis = αNow, Radius of circle can be given as,
R = l.sinα
Given the period of the conical pendulum as 1.4s
we can find the acceleration due to gravity as follows = 2π(r/g)1/2r = l.sinα2π(r/g)1/2 = Tg = 4π2(l.sinα)2/T2g = 4π2(l2sin2α)/T2sinα = gT2/4π2l2Sinα = (9.8 m/s2× 1.4 s2)/(4π2 × (0.9 m)2)Sinα = 0.253α = sin-1(0.253)α = 14.68°
Hence, the angle made by the string with the vertical axis is 14.68°.
To know more about Pendulum please visit :
https://brainly.com/question/29225143
#SPJ11
what is the log2(100)? it or use a calculator. (to 2 decimal places) round that number up to the next highest integer: based on the tests you've done: what is the maximum number of iterations used for quick search on a collection of 100 items? what is the maximum number of iterations used for linear search on a collections of 100 items? what is the bigo of quick search? hint: n
Log2(100) is 6.64 to 2 decimal places. Rounded up to the next highest integer, it is 7. Based on the tests done, the maximum number of iterations used for quick search on a collection of 100 items is 7 iterations.
The maximum number of iterations used for linear search on a collection of 100 items is 100 iterations. The big O of quick search is O(n log n).
log2(100) is the same as x in 2^x=100
This means 2^6.64=100
To solve for 6.64, take the logarithm of both sides.
log(2^6.64)=log(100)
6.64log(2)=log(100)
6.64=2log(10)+2log(5)
log(2)+log(1.25)+log(10)=6.64
log(2)+log(1.25)=6.64-log(10)
log(2)+log(1.25)=2.02
log(2x1.25)=2.02x2^(log(2)+log(1.25))=2.02 x 2^(log(10))=7 (rounded up)
The maximum number of iterations used for quick search on a collection of 100 items is 7 iterations.
The maximum number of iterations used for linear search on a collection of 100 items is 100 iterations. In big O notation, the time complexity of linear search is O(n).
To learn more about "log2(100)", visit: https://brainly.com/question/15602305
#SPJ11
I need the question of this page filled with steps...... I'm confused
i) The velocity of the particle at 17 sec is 17m/s.
ii) The total distance travelled is 190 m.
iii) The total displacement is -10m.
What is the difference between distance and displacement?Distance is the length of any path connecting any two places. As measured along the shortest path between any two points, displacement is the direct distance between them.
The direction is ignored when calculating distance. The direction is accounted for in the displacement calculation.
Since it solely depends on magnitude and not direction, distance is a scalar number. Since displacement varies on both magnitude and direction, it is a vector quantity.
Distance provides specific directions that must be taken when moving from one location to another. Displacement only provides a partial description of the route because it pertains to the quickest way.
Velocity of particle = Slope of the object =Δ [tex]\frac{y}{x}[/tex]
Velocity = [tex]\frac{95-10}{20-15}[/tex] = 17m/s
To know more about Displacement, visit:
https://brainly.com/question/11934397
#SPJ1
the end result of a theory that is not verified is
Unproven theories ultimately cannot be regarded as scientific facts or principles and are not generally recognised by the scientific community.
A well-supported explanation of a natural occurrence in science that has passed rigorous examination and is backed by empirical data is referred to as a theory. A hypothesis, however, cannot be regarded as a scientific fact or principle if it is not backed up by empirical data or if it has not undergone extensive testing and verification. The scientific community frequently rejects unproven notions with scant empirical backing and may even label them as pseudoscientific or non-scientific. This is so that scientific theories and findings may be evaluated and verified frequently. Science does this by using evidence-based reasoning and critical thinking. Unproven theories are therefore eventually not regarded as being a part of the corpus of scientific knowledge.
learn more about theories here:
https://brainly.com/question/1759635
#SPJ4
how do the summer and winter monsoon affect climate in the region?
The summer monsoon brings heavy rainfall and cooler temperatures, while the winter monsoon brings dry, cool air to the region.
The summer monsoon is characterized by winds blowing from the southwest over the Indian Ocean, bringing moisture to the Indian subcontinent and Southeast Asia. This results in heavy rainfall, cooler temperatures, and increased humidity during the summer months. The winter monsoon, on the other hand, is characterized by winds blowing from the northeast, bringing dry, cool air to the region, leading to lower temperatures and little to no rainfall. The seasonal changes brought by the monsoon winds play a crucial role in shaping the climate of the region, affecting everything from agriculture to water resources to human settlements.
To know more about monsoons, here
brainly.com/question/22831604
#SPJ4
A basketball rolls across a floor without slipping, with its centerof mass moving at a certain velocity. A block of ice of the samemass is set sliding across the floor with the same speed along aparallel line.(a) How do their energies compare?The ice has more kineticenergy.They have equal kineticenergies.The basketball has more kineticenergy.
The correct option is A, A block of ice of the same mass is set sliding across the floor with the same speed along a parallel line The ice has more kinetic energy.
Kinetic energy is a type of energy that an object possesses by virtue of its motion. It is defined as the energy an object has due to its motion and is proportional to the mass of the object and the square of its velocity. The formula for kinetic energy is KE = 1/2mv², where m is the mass of the object and v is its velocity.
Kinetic energy is a scalar quantity and has units of joules in the International System of Units (SI). It is a fundamental concept in physics and is used to describe many physical phenomena, including the motion of particles, the behavior of gases, and the motion of waves. In many cases, kinetic energy can be transformed into other forms of energy. For example, when a ball is thrown upwards, its kinetic energy is gradually converted into gravitational potential energy as it moves higher and higher.
To learn more about Kinetic energy visit here:
brainly.com/question/26472013
#SPJ4
Complete Question:
Basketball rolls across a floor without slipping, with its center of mass moving at a certain velocity. A block of ice of the same mass is set sliding across the floor with the same speed along a parallel line.(a) How do their energies compare?
A). The ice has more kinetic energy.
B). They have equal kinetic energies.
C). The basketball has more kinetic energy.
(a) Find the current in an 8.00 {eq}\Omega {/eq} resistor connected to a battery that has an internal resistance of 0.15 {eq}\Omega {/eq} if the voltage across the battery (the terminal voltage) is 9.00 V.
(b) What is the emf of the battery?
(a) The current in the 8.00 Ω resistor connected to a battery that has an internal resistance of 0.15 Ω and a terminal voltage of 9.00 V is 1.0 A.
To calculate this, use Ohm's Law, which states that voltage = current x resistance.
Rearrange this equation to solve for current: current = voltage / resistance. Plug in the values for voltage and resistance to get:
current = 9.00 V / 8.00 Ω + 0.15 Ω = 1.0 A.
(b) The EMF (electromotive force) of the battery is 9.00 V. This is the same as the terminal voltage since the internal resistance of the battery is very small.
Learn more about resistance at : https://brainly.com/question/24119414
#SPJ11
