A body with an initial velocity of 10m/s has an acceleration of 8m/s^2. Determine graphically the velocity after 5 seconds, & the distance travelled in that time. Verify your answer using the equations of motion.
Answers
Answer:
From the graph, at t = 5 seconds, the velocity = 50 m/s as shown also in the above table
Please find attached the graph
Explanation:
The initial velocity of the body = m/s
The acceleration of the body = 8 m/s²
The velocity after 5 seconds can be determined graphically and by calculation as follows;
Graphically, we have the data points which can be found by the straight line relation v = u + a×t,
Where ,
a = The slope = 8 m/s²
u = 10 m/s = The y-intercept
Which gives;
v = 10 + 8 × t
The following data can be calculated for various time t;
Time, t Velocity , v
0, 10
1, 18
2, 26
3, 34
4, 42
5, 50
6, 58
From the graph, at t = 5 seconds, the velocity = 50 m/s as shown also in the above table
Please find attached the graph
By calculation, we have;
v = u + a×t
Where;
v = The final velocity
u = The initial velocity = 10 m/s
a = The acceleration = 8 m/s²
t = The time = 5 seconds
v = 10 + 5× 8 = 50 m/s.
Related Questions
How much does the speed of a car increase if it accelerates
uniformly at 2.5 meters per second squared for 5 seconds?
Answers
Answer:
12.5 m/s
Explanation:
a = Δv / Δt
2.5 m/s² = Δv / 5 s
Δv = 12.5 m/s
What is the difference between virtual images produced by concave, plane, and convex mirrors?
What does the negative sign in the value of magnification produced by a mirror indicate about
an image?
Answers
Answer:
Explanation:
A concave mirror is a curved mirror that is coated outwards. The outer part of the mirror is always coated. The nature of image formed by an object placed in front of a concave mirror can be real or virtual depending on the distance of the object on the axis from the mirror. The only time the object produces a virtual image is when it is placed between the focus and the pole of the mirror. The virtual image formed is a "MAGNIFIED and upright image"
For a convex mirror, the inner part is always coated and the nature of the image formed by the object doesn't depend on the distance between the image and the mirror. No matter where the object is placed, the image formed will always be virtual, upright and DIMINISHED. This means that magnification is always less than 1.
For a plane mirror, the nature of the image produced by a plane mirror also virtual because it is always formed behind the mirror. The size of the image formed is always THE SAME as that of the object. This means that the magnification is always equal to 1.
a) In summary, the difference between virtual images produced by concave, plane, and convex mirrors is that virtual images produced by concave mirror are MAGNIFIED, virtual images produced by plane mirror are THE SAME SIZE as that of the object and virtual images produced by convex mirrors are always DIMINISHED.
b) Magnification is defined as the ratio of the image distance to the object distance. Mag = v/u
Note that object distances are always positive, hence it is only the image distance that can either be positive or negative which in turn affects the magnification causing it to be positive or negative.
Negative image distance shows that the image is virtual while positive image distance shows that the image is real.
A negative magnification therefore shows that the nature of the image is a virtual image.
A car is driving at 99 km/h, calculate the distance it travels in 70 minutes.
Give your answer in correct SI units rounded to 0 decimal places.
Answers
Answer:
The distance the car travels is 115500 m in S.I units
Explanation:
Distance d = vt where v = speed of the car and t = time taken to travel
Now v = 99 km/h. We now convert it to S.I units. So
v = 99 km/h = 99 × 1000 m/(1 × 3600 s)
v = 99000 m/3600 s
v = 27.5 m/s
The speed of the car is 27.5 m/s in S.I units
We now convert the time t = 70 minutes to seconds by multiplying it by 60.
So, t = 70 min = 70 × 60 s = 4200 s
The time taken to travel is 4200 s in S.I units
Now the distance, d = vt
d = 27.5 m/s × 4200 s
d = 115500 m
So, the distance the car travels is 115500 m in S.I units
what is space in detail?
Answers
Answer:
Space in the astronomy and cosmology space is 3 dimensional region and earth atmosphere end is called space.
Explanation:
Space is the everything of the top earth atmosphere moon, starts, milky way, black hole and GPS satellites an distant,space also called between stars,moon,planet.
Space is all the extends far in all directions, space is finite unbound space surface of the earth has finite are no beginning or not end.
Space contains there are three dimensions is called 3 D space,an space is to refer an interval during signal transmitted also used by the character, bytes, words and octets in digital signal.
space is that term can refer to various in science, communications and mathematics,and maintain orbits for responsible time, space is usually to begin at the lowest attitude satellites can maintain orbits.
space coordinates are uniquely define the location of any particular point and that continuum requires more than coordinates,and the number of dimensions and conventional space or digital communications during the signal represents logic is 0 words in a digital signal.
n this activity, you will answer questions based on these two scenarios. Scenario 1 It’s the week before final exams, and Alicia is looking forward to graduation. However, she knows the week will be stressful. In addition to studying hard for her exams, her manager at work called and asked her to work an additional 15 hours. Her softball coach scheduled double practices to prepare for state finals. Her aunt has asked her to babysit her niece a few hours each night. On top of all this, she wants to spend some much-needed quality time with her friends. Alicia wishes there were 86 hours in a day instead of 24. Scenario 2 A small nation's economy depends on oil. The country’s earnings have declined greatly because of a recent drop in oil prices. The government uses these earnings to provide free education to all citizens under the age of 25. The country also uses its earnings to provide free health care and to provide benefits for retirees. The government also uses part of its earnings to help a neighboring country recover from a natural disaster. The president of the country imagines how much he could help his citizens if there weren’t any budget restrictions. Part A What do Alicia and the president have in common?
Answers
Answer: Alicia and the president do not have enough of a particular resource. Alicia doesn’t have enough time, and the president doesn’t have enough money.
Explanation: This is Plato's sample answer.
64. A heart pacemaker fires 72 times a minute, each time a 25.0-nF capacitor is charged (by a battery in series with a resistor) to 0.632 of its full voltage. What is the value of the resistance
Answers
Answer:
=33 .3×10^6Ω
=33.3M Ω
Explanation:
We were told to calculate the Resistance value,
Given the heart pacemaker fires as 72 times a minute, which is the time constant
Then we can convert the pacemaker fires of 72 times a minute to seconds for unit consistency.
1 minutes= 60secs
Then ,Time constant τ=60secs/72=0.8333 seconds
Time constant τ can be calculated using the formula below
τ= RC
Where R= resistance
C = capacitance
Then making RESISTANCE subject of formula we have
R=τ/C
But Capacitance=25.0-nF = 25×10^25F
Substitute the values we have
R=0.833/25×10^25
=33 .3×10^6 Ω
But can still be converted to M Ω= 33.3M Ω
Therefore, the resistance is 33 .3×10^6 Ω or 33.3M Ω
NOTE: 1M= 10^6
The value of the resistance will be "3.33×10⁷ Ω".
Resistance based problem:According to the question,
Capacitor, C = 25.0 nF
60 sec - 72 fires
now,
Time for 1 fire,
[tex]t = \frac{60}{72}[/tex]
[tex]= \frac{5}{6} \ sec[/tex]
Now,
⇒ [tex]V = V_0 (1-e^{-\frac{t}{RC} })[/tex]
[tex]0.632 V_0=V_0(1-e^{\frac{-\frac{5}{6} }{R.25 n C} })[/tex]
[tex]e^{-\frac{1}{R\times 30\times 10^{-9}} } = 1-0.632 = 0.368[/tex]
[tex]= 2.72[/tex]
By taking "log" both sides,
⇒ [tex]ln \ e^{\frac{1}{R\times 30\times 10^{-9}} } = ln \ 2.72[/tex]
hence,
The Resistance be:
⇒ [tex]R = \frac{10^9}{30}[/tex]
[tex]= 3.33\times 10^7 \ \Omega[/tex]
Thus the above approach is right.
Find out more information about resistance here:
https://brainly.com/question/76343
what type of image is formed by a lens if m = -0.87
A. The image is larger than the object and the image is real
B. The image is smaller than the object and the object is real
C. The image is larger than the object and is virtual
D. The image is smaller than the object and is virtual
Answers
Answer:
B.
Explanation:
as there is a '-' sign before the magnification value, it forms a real image.
so the last two options get cancelled.
as the value of magnification is 0.87 ie. lesser than 1, we can say that the image is smaller.
The type of image is formed by a lens if m = -0.87 would be smaller than the object and the object is real
What is a lens?A lens is a transmissive optical tool that employs refraction to focus or disperse a light beam. The power of the lens is expressed in the dioptre which is the reciprocal of the focal length of the lens.
The image formation through the lens is calculated with the help of the lens formula given as follows
1/f = 1/v - 1/u
where f is the focal length of the lens
u is the distance of the object from the lens
v is the distance of the image formed from the
magnification (m) = size of image /size of the object
As given in the problem image is formed by a lens if m = -0.87
Thus, the negative sign represents that the image formed by the object is real, and the magnitude of the magnification is less than 1 this represents that size of the image is smaller than the size of the object.
Learn more about the lens from here
https://brainly.com/question/766997
#SPJ2
Compare diffusion of chlorine gas into air and into vaccuum. Explain your answer
Answers
Answer:
Diffusion depends among many other things also upon the concentration gradient of the diffusing substance.For example if there are two boxes with given particles first isolated from each other and if they are bought in contact, then there is a net diffusion of particles from a box with higher concentration of particles to box with lower concentration. And also diffusion rate depends at any instant directly on the concentration difference between them at that instant.Now the vaccum is equivalent to an empty box which means with this one leads to a maximum diffusion rate when bought in contact with a box with particles because there is maximum concentration difference.That is vaccum is empty ( except for energy perturbations and a small concentration of particles which will be zero for our purpose) and any bunch of particles will find least resistance to diffuse as just outside this bunch there is ‘0' concentration of the particles.
Can someone explain how the weight of the block is 10.26N, with reference to an appropriate law of motion?
Answers
this process is called parellelogram method of resolving vectors.
A hammer is used to hit a nail into a board. Which statement is correct about the forces at play between the nail and the hammer? The nail exerts an equal force on the hammer in the same direction. The nail exerts a much smaller force on the hammer in the opposite direction. The nail exerts an equal force on the hammer in the opposite direction. The nail exerts a much smaller force on the hammer in the same direction.
Answers
Answer:
The nail exerts an equal force on the hammer in the opposite direction.
Explanation:
The Newtons third law states that there is an equal an opposite reaction for every action. When hammer pushes the nail, the nail will push the hammer back in opposite direction. When the hammer hits a nail then nail will exert the equal and opposite force to the hammer. These both objects will exert force on each other in opposite directions.
Hello, I am BrotherEye
Answer:
Answers are
1. "The nail exerts an equal force on the hammer in the opposite direction."
2. "500 N"
3. "The iron piece exerts a force of 1 N on the magnet in the opposite direction."
4. "When mass moves closer to the point of rotation, rotational inertia decreases."
5. "The skater spins slower because his rotational inertia has increased."
Explanation:
A stone of 1 kg is thrown with a velocity of 40 m/s across the frozen surface of a lake and comes to rest after travelling a distance of 50 m. What is the force of friction between the stone and the ice? *
A)16 N
B)-4 N
C)-16 N
Answers
Answer:
C)-16 N
Explanation:
concepts used
force = mass* acceleration
equation of motion
[tex]v^2 = u^2 + 2as[/tex]
where v is the final velocity
u is the initial velocity
and s is the distance moved
______________________________________________
Given
mass = 1 kg
initial velocity (u) = 40m/s
final velocity (v) = 0 as stones comes to rest
distance moved by stone (s) = 50m
using [tex]v^2 = u^2 + 2as[/tex]
[tex]0 = 40^2 +2a*50\\=> -1600 = 100a\\=> a = -1600/100 = -16[/tex]
Thus, acceleration is -16 m/s^2
here acceleration is negative as force of friction is opposing the motion.
Force of friction = mass of stone * acceleration of stone
Force of friction = 1*-16 kgm/s^2 = -16N ( kgm/s^2 = 1 N)
Thus, option c -16N is correct choice.
1 point
40 The diagram below shows an electrical circuit made up of a cell and three loads. The
voltage established by the cell and the resistance of each load is marked on the
diagram. Select the current flowing through the 3-ohm load.
www
1 ohm
12V
2 ohms
WWW
3 ohms
www
A. 4 amps
B. 2 amps
C. 5 amps
D. 0.25 amps
SPS106 DOK 3
Answers
Answer:
Option B. 2 A.
Explanation:
The following data were obtained from the question:
Resistance 1 (R1) = 1 Ω
Resistance 2 (R2) = 2 Ω
Resistance 3 (R3) = 3 Ω
Potential difference (V) = 12 V.
Current through the 3 Ω (I3) =?
Next, we shall determine the total resistance of the circuit.
This can be obtained as follow:
Resistance 1 (R1) = 1 Ω
Resistance 2 (R2) = 2 Ω
Resistance 3 (R3) = 3 Ω
Total resistance (R) =.?
R = R1 + R2 + R3
R = 1 + 2 + 3
R = 6 Ω
Next, we shall determine the current flowing in the circuit.
This can be obtained as follow:
From ohm's law,
Voltage (V) = current (I) x resistance (R)
V = IR
Potential difference (V) = 12 V.
Resistance (R) = 6 Ω
Current (I) =?
V = IR
12 = I x 6
Divide both side by 6
I = 12/6
I = 2 A.
Since the circuit is in series connection, therefore, the same current will flow through each resistor.
Therefore, the current through the the 3 Ω load is 2 A.
A dog is 10 m from a cat, whose speeds are 6 and 5 m / s, respectively. What time does the dog require to catch the cat?
Answers
Answer:
10 seconds
Explanation:
because the cat is moving one m/s slower than the dog, the dog has a relative speed of 1 m/s. 10 meters would take 10 seconds for the dog to cover
A block is attached to the end of a spring. The block is then displaced from its equilibrium position and released. Subsequently, the block moves back and forth on a frictionless surface without any losses due to friction. Which one of the following statements concerning the total mechanical energy of the block-spring system this situation is true?
1. The total mechanical energy is dependent on the maximum displacement during the motion.
2. The total mechanical energy is at its maximum when the block is at its equilibrium position
3. The total mechanical energy is constant as the block moves back and forth.
4. The total mechanical energy is only dependent on the spring constant and the mass of the block.
Answers
Answer:
The correct option is;
3. The total mechanical energy is constant as the block moves back and forth
Explanation:
The total mechanical energy is the sum of the potential and kinetic energies of the system
For a system that is isolated from the effects of external forces, but being acted upon by the internal conservative forces within the system, the total mechanical energy is constant
For a black and spring system, we have total mechanical energy, E = 1/2×K×A².
Where;
K = Constant
A = The amplitude of motion
Therefore, where there is no loss to friction, with A, remaining constant, the total mechanical energy will be constant.
A cat stalks an unsuspecting mouse. The movement of the cat is shown in the following graph of the horizontal position, x, against time, t. What is the average speed of the cat between t = 2s and t = 6s?
Answers
Answer:
0.25 m/s
Explanation:
Average velocity = change in displacement / change in time
v = (1.5 m − 2.5 m) / (6 s − 2 s)
v = -0.25 m/s
The average speed is 0.25 m/s.
Answer:
0.25 m/s
Explanation:
khan academy
SHOW ADEQUATE WORKINGS IN THIS SECTION
12. Wale and Lekan of 55kg and 60kg respectively ran a race of 200m.
i. Calculate their work done in KJ
ii. If wale finished the race in 25secs while Lekan finished in 30secs, calculate their
power and who is more powerful out of these two. ( g = 10m/secs)
13. A machine has a velocity ratio of 5 and is 800
/0 efficient. If the machine is carrying a load
of 200kg, what will be effort applied?
Please help me answer anyone that you understand
Answers
Answer:
12 i. The work done by Wale = 107.910 kJ
The work done by Lekan = 117.720 kJ
Total work done = 225.36 kJ
ii. Wale's power = 4.3164 kW
Lekan's power = 3.924 kW
Wale has more power and is more powerful than Lekan
13. 313.92 N
Explanation:
i. The work done, W = Force, F × Distance moved by the force, D
The given parameters are
The mass of Wale = 55 kg
The mass of Lekan = 60 kg
The acceleration due to gravity, g =9.81 m/s²
The motion force of Wale and Lekan are;
Motion force of Wale = 9.81 × 55 = 539.55 N
Motion force of Lekan = 9.81 × 60 = 588.6 N
The work done by Wale = 539.55 × 200 = 107910 J = 107.910 kJ
The work done by Lekan= 588.6 × 200 = 117720 J = 117.720 kJ
107910 + 117720 =225630 J = 225.36 kJ
ii. Power = Work done/time
Wale finished the race in 25 s, therefore, his power = 107910/25 = 4316.4 W
Lekan finished the race in 30 s, therefore, his power = 117720/30 = 3924 W
Wale has more power and is more powerful than Lekan
13. The velocity ratio = 5
V. R. = Distance moved by effort/(Distance moved by load)
Efficiency = 80%
Work done by effort = x
Work done by machine = Efficiency × Work done by effort = 0.8 × x
Distance moved by effort, E = V. R. × Distance moved by load, D = 5 × D
Work done by effort = Force × Distance moved = 200×9.81× E
Work done by effort = 1962×E = 1962×E = 1962×5×D
Work done by machine = 1962 × D, when D = 1, we have;
0.8 × 1962×1 = 1569.6 J
Work done by effort = Force × Distance moved
Work done by effort = Force × 5×D = Force × 5 (D = 1)
From the principle of conservation of energy, we have;
Energy is neither created nor destroyed
Therefore
Work done by effort = Force × 5 = 1569.6 J
Force = 1569.6 /5 = 313.92 N.
A car is moving on straight highway with a speed of 108 km/h.
Answers
Answer:
5.3333 sec
Explanation:
initial speed: u = 108km/hr or 30 m/s
final speed: v = 0m/s
distance travelled: s = 80m
time the car took to stop: = t sec
[tex]v^{2} - u^{2}[/tex] = 2as,
a = ([tex]v^{2} - u^{2}[/tex])/2s
a = (0-900)/160
a = -5.625 [tex]ms^{-2}[/tex]
v = u + at,
t = (v - u)/a
t= (0 - 30)/(-5.625)
t = 5.3333 sec
A small cylinder is rolled along a ruler and completes two revolutions. The circumference is the distance around the outside of a circle. What is the circumference of the cylinder? A 4.4 cm B 5.2 cm C 8.8 cm D 10.2 cm
Answers
Answer; 4.4cm
Explanation: There is a ruler upon which the cylinder start from 1.4cm and reaches 10.2cm
distance traveled =10.2-1.4=8.8
since this cylinder is small so the linear distance can be approximately taked as rotational distance(as in case of point charge) so
2x2πxr =8.8
so the circumference will be 2πr=4.4cm
If the spring constant is 10 N/m and the spring is stretched 1 m, what is the Force?
Answers
Answer:
10N
Explanation:
Applying the Hooke law:
F = kx
F: Force
k: stiffness coefficient
x: stretched distance
F = 10N/m x 1m = 10N
The marginal cost curve
(a) Lies below the ATC curve when the ATC curve slopes upward.
(b) Intersects the AFC and ATC curves at their respective minimum points.
(c) Lies above the AVC curve when the AVC curve slopes downward.
(d) Intersects the AFC and AVC curves at their respective minimum points.
(e) Intersects the AVC and ATC curves at their respective minimum points
Answers
Answer:
c
Explanation:
The marginal cost curve image has been attached from which we can clearly, indicate that
ATC = average total cost
AFC = average fixed cost
AVC = average variable cost.
From the graph we can indicate that the marginal cost curve
(c) Lies above the AVC curve when the AVC curve slopes downward.
PLS HELP ME Define Derived Quantities ?
Answers
Derived Quantities
Explanation: Those physical quantities which are derived from fundamental quantities are called derived quantities and their units are called derived units. e.g., velocity, acceleration, force, work etc.
Answer:
These are quantities calculated from two or more measurements
Explanation:
They can't me measured directly.
They can only be computed.
They are calculated in PHYSICAL SCIENCE.
hope it helps.
what is a hypothesis reffered to as after being verified by a large number or independent experiments
Answers
Answer:
The hypothesis may or may not be true and needs to be tested. It might be the answer to the problem. Hence, it must be tested thoroughly. When these predictions are tested again and again in independent scientific experiments and gets verified, the hypothesis is converted into a scientific theory.
SCIENCE
1-1 FORCE
What is gravitational force?
(गुरुत्वाकर्षण बल भनेको के हो?"
Write two factors that affect gravitation, (गुरुत्वाकर्षणलाई असर
Write one effect of gravitation that is seen in the sea. (गुरुत्वा
What is gravitational constant? (गुरुत्वाकर्षण अचर भनेको हो ?
Write the value of gravitational constant? (गुरुत्वाकर्षण अचरक
What is gravity? (गुरुत्व बल के हो?)
Vrite two factors that affect ravity. (गुरुत्व बललाई असर गर्ने
-2 FORCE
What is acceleration due to gravity? (गुरुत्व प्रवेग के हो)
rite the value of g at the poles and in the equator of the
त उल
Answers
Answer:
is a force that attracts any two objects with a mass
If 5 complete oscillations of a sound wave pass through a point in 0.5 s and the speed of sound was recorded to be 10 m/s, then find the wavelength of the sound.
Answers
Answer:
λ = 2.5m
Explanation:
Given the following :
Speed of sound (v) = 10m/s
If 5 oscillations pass through a point in 0.5seconds;
Time taken (period) for 1 oscillation is :
Number of oscillations / total time taken
5 / 0.5 = 0.25 seconds
Wavelength, period and Velocity are related by the formula:
v = λ / T
λ = v * T
λ = 10 * 0.25
λ = 2.5 m
You have a cup with 50cm filled with water. How much pressure will the water act on the bottom of the cup? The density of water is 1000kg/m^3 and g = 10N/kg
Answers
Answer:
5000 N/m².
Explanation:
The following data were obtained from the question:
Density (d) = 1000 kg/m³
Acceleration due to gravity (g) = 10 N/kg
Height (h) = 50 cm = 50/100 = 0.5 m
Pressure (P) =.?
Pressure is related to density and height by the following equation:
P = dgh
Where
P is the pressure.
d is the density.
g is the acceleration due to gravity.
h is the height.
With the above formula, we can obtain the pressure at the bottom of the cup as follow:
P = dgh
P = 1000 x 10 x 0.5
P = 5000 N/m²
Therefore, the pressure at bottom of the cup is 5000 N/m².
A charge (uniform linear density = 8.8 nC/m) lies on a string that is stretched along an x axis from x = 0 to x = 3.1 m. Determine the magnitude of the electric field at x = 5.2 m on the x axis.
Answers
Answer:
answer= 73.1256 [tex]i[/tex]
Explanation:
The electric charge linear density is equal to 8.8 x[tex]10^{-9}[/tex]
the length of the string is 3.1m
The magnitude of the electric field at the length of the string equal to 5.2 meters can be calculated with the formula ;
- E = λ / 4πε₀ [ [tex]l[/tex] / α ( α +
Solution:
E = 8.8 x[tex]10^{-9}[/tex] / 4πε₀ [ 3.1/ 5.2( 5.2 + 3.1) ] [tex]i[/tex]
= 1018.0995 [0.07183] [tex]i[/tex]
= 73.1256 [tex]i[/tex]
Light travels at a speed of 2.998*108 m/s. Light takes approximately 3.25 minutes to travel from the Sun to reach a planet. Calculate the distance from the Sun to this planet in meters. Give your answer to 0 decimal places.
Answers
Answer:
585×10⁸ m
Explanation:
Distance = rate × time
d = (2.998×10⁸ m/s) (3.25 min) (60 s/min)
d = 585×10⁸ m
An electron and a proton are 6.5x10 ^ -11 m apart, find the magnitude of the electric and gravitational force between the two particles
Answers
Explanation:
The electric force is:
F = k q₁ q₂ / r²
F = (9×10⁹ Nm²/C²) (-1.6×10⁻¹⁹ C) (+1.6×10⁻¹⁹ C) / (6.5×10⁻¹¹ m)²
F = 5.4×10⁻⁸ N
The gravitational force is:
F = G m₁ m₂ / r²
F = (6.67×10⁻¹¹ Nm²/kg²) (9.11×10⁻³¹ kg) (1.67×10⁻²⁷ kg) / (6.5×10⁻¹¹ m)²
F = 2.40×10⁻⁴⁷ N
A 0.149 kg glider is moving to the right on a frictionless, horizontal air track with a speed of 0.710 m/s . It has a head-on collision with a 0.308 kg glider that is moving to the left with a speed of 2.27 m/s . Suppose the collision is elastic.1. Find the magnitude of the final velocity of the 0.157kg glider.
2. Find the magnitude of the final velocity of the 0.306kg glider.
Answers
Answer:
v1 = −2.201946 m/s ( to the left)
v2 = 0.7780534 m/s ( to the right)
Explanation:
Given the following :
Mass of first glider (m1) = 0.149kg
Initial Speed of first glider (u1) = 0.710 m/s
Mass of second glider (m2) = 0.308kg
Initial Speed of second glider (u2) = 2.27m/s
For elastic collision:
m1u1 + mu2u2 = m1v1 + m2v2
Where V1 and v2 = final velocities if the body after collision.
Taking right as positive ; left as negative
u1 = 0.710m/s ; u2 = - 2.27m/s
u1 - u2 = - (v1 - v2)
0.710 - - 2.27 = - v1 + v2
v2 - v1 = 2.98 - - - - (1)
From:
m1u1 + mu2u2 = m1v1 + m2v2
(0.149 * 0.710) + ( 0.308 * - 2.27) = (0.149 * v1) + (0.308 * v2)
0.10579 + (-0.69916) = 0.149 v1 + 0.308v2
−0.59337 = 0.149 v1 + 0.308v2
Dividing both sides by 0.149
v1 + 2.067v2 = −0.59337 - - - - - (2)
From (1)
v2 = 2.98 + v1
v1 + 2.067(2.98 + v1) = −0.59337
v1 + 6.16 + 2.067v1 = −0.59337
3.067v1 = −0.59337 - 6.16
3.067v1 = −6.75337
v1 = −6.75337 / 3.067
v1 = −2.201946 m/s ( to the left)
From v2 = 2.98 + v1
v2 = 2.98 + (-2.201946)
v2 = 0.7780534 m/s ( to the right)
One glass microscope slide is placed on top of another with their left edges in con- tact and a human hair under the right edge of the upper slide. As a result, a wedge of air exists between the slides. An interference pattern results when monochromatic light is incident on the wedge. What is observed at the left edge of the slides? a. A dark fringe b. A bright fringe c. Impossible to determine
Answers
Answer:
A dark fringe
