The ball's horizontal position in the air is
[tex]x=\left(27.5\dfrac{\rm m}{\rm s}\right)\cos38.5^\circ t[/tex]
It hits the wall when [tex]x=17.5\,\mathrm m[/tex], which happens at
[tex]17.5\,\mathrm m=\left(27.5\dfrac{\rm m}{\rm s}\right)\cos38.5^\circ t\implies t\approx0.813\,\mathrm s[/tex]
Meanwhile, the ball's vertical position is
[tex]y=\left(27.5\dfrac{\rm m}{\rm s}\right)\sin38.5^\circ t-\dfrac g2t^2[/tex]
where [tex]g[/tex] is the acceleration due to gravity, 9.80 m/s^2.
At the time the ball hits the wall, its vertical position (relative to its initial position) is
[tex]y=\left(27.5\dfrac{\rm m}{\rm s}\right)\sin38.5^\circ(0.813\,\mathrm s)-\dfrac g2(0.813\,\mathrm s)^2\approx\boxed{10.7\,\mathrm m}[/tex]
A particle moves along line segments from the origin to the points (1, 0, 0), (1, 5, 1), (0, 5, 1), and back to the origin under the influence of the force field. F(x, y, z)= z^2i + 4xyj + 5y^2kFind the work done.
Answer:
0 J
Explanation:
Since work done W = ∫F.dr and F(x, y, z)= z²i + 4xyj + 5y²k and dr = dxi + dyj + dzk
F.dr = (z²i + 4xyj + 5y²k).(dxi + dyj + dzk) = z²dx + 4xydy + 5y²dz
W = ∫F.dr = ∫z²dx + 4xydy + 5y²dz = z²x + 2xy² + 5y²z
We now evaluate the work done for the different regions
W₁ = work done from (0,0,0) to (1,0,0)
W₁ = {z²x + 2xy² + 5y²z}₀₀₀¹⁰⁰ = 0²(1) + 2(1)(0)² + 5(0)²(0) - [(0)²(0) + 2(0)(0)² + 5(0)²(0)] = 0 - 0 = 0 J
W₂ = work done from (1,0,0) to (1,5,1)
W₂ = {z²x + 2xy² + 5y²z}₁₀₀¹⁵¹ = (1)²(1) + 2(1)(5)² + 5(5)²(1) - [0²(1) + 2(1)(0)² + 5(0)²(0)] = 1 + 50 + 125 - 0 = 176 J
W₃ = work done from (1,5,1) to (0,5,1)
W₃ = {z²x + 2xy² + 5y²z}₁₅₁⁰⁵¹ = 1²(0) + 2(0)(5)² + 5(5)²(1) - [(1)²(1) + 2(1)(5)² + 5(5)²(1)] = 125 - (1 + 50 + 125) = 125 - 176 = -51 J
W₄ = work done from (0,5,1) to (0,0,0)
W₄ = {z²x + 2xy² + 5y²z}₁₅₁⁰⁰⁰ = (0)²(0) + 2(0)(0)² + 5(0)²(0) - [1²(0) + 2(0)(5)² + 5(5)²(1)] = 0 - 125 = -125 J
The total work done W is thus
W = W₁ + W₂ + W₃ + W₄
W = 0 J + 176 J - 51 J - 125 J
W = 176 J - 176 J
W = 0 J
The total work done equals 0 J
A 120-V rms voltage at 60.0 Hz is applied across an inductor, a capacitor, and a resistor in series. If the peak current in this circuit is 0.8484 A, what is the impedance of this circuit?
A) 200 Ω
B) 141 Ω
C) 20.4 Ω
D) 120 Ω
E) 100 Ω
Answer:A 200
Explanation:
Vp=1.41*Vrms
Vp=169.7 v
Z=Vp/Ip
Z=169.7/.8484
Z=200.03 ohm
A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .Part A. Calcualte the coil's self-inductance.Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf froma to b or from b to a?
Complete Question
A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .
Part A. Calculate the coil's self-inductance.
Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.
Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf from a to b or from b to a?
Answer:
Part A
[tex]L = 0.000863 \ H[/tex]
Part B
[tex]\epsilon = 0.863 \ V[/tex]
Part C
From terminal a to terminal b
Explanation:
From the question we are told that
The number of turns is [tex]N = 590 \ turns[/tex]
The cross-sectional area is [tex]A = 6.20 cm^2 = 6.20 *10^{-4} \ m[/tex]
The radius is [tex]r = 5.0 \ cm = 0.05 \ m[/tex]
Generally the coils self -inductance is mathematically represented as
[tex]L = \frac{ \mu_o N^2 A }{2 \pi * r }[/tex]
Where [tex]\mu_o[/tex] is the permeability of free space with value [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]
substituting values
[tex]L = \frac{ 4\pi * 10^{-7} * 590^2 6.20 *10^{-4} }{2 \pi * 0.05 }[/tex]
[tex]L = \frac{ 2 * 10^{-7} * 590^2 6.20 *10^{-4} }{ 0.05 }[/tex]
[tex]L = 0.000863 \ H[/tex]
Considering the Part B
Initial current is [tex]I_1 = 5.00 \ A[/tex]
Current at time t is [tex]I_t = 3.0 \ A[/tex]
The time taken is [tex]\Delta t = 3.00 ms = 0.003 \ s[/tex]
The self-induced emf is mathematically evaluated as
[tex]\epsilon = L * \frac{\Delta I}{ \Delta t }[/tex]
=> [tex]\epsilon = L * \frac{ I_1 - I_t }{ \Delta t }[/tex]
substituting values
[tex]\epsilon = 0.000863 * \frac{ 5- 2 }{ 0.003 }[/tex]
[tex]\epsilon = 0.863 \ V[/tex]
The direction of the induced emf is from a to b because according to Lenz's law the induced emf moves in the same direction as the current
This question involves the concepts of the self-inductance, induced emf, and Lenz's Law
A. The coil's self-inductance is "0.863 mH".
B. The self-induced emf in the coil is "0.58 volts".
C. The direction of the induced emf is "from b to a".
A.
The self-inductance of the coil is given by the following formula:
[tex]L=\frac{\mu_oN^2A}{2\pi r}[/tex]
where,
L = self-inductance = ?
[tex]\mu_o[/tex] = permeability of free space = 4π x 10⁻⁷ N/A²
N = No. of turns = 590
A = Cross-sectional area = 6.2 cm² = 6.2 x 10⁻⁴ m²
r = radius = 5 cm = 0.05 m
Therefore,
[tex]L=\frac{(4\pi\ x\ 10^{-7}\ N/A^2)(590)^2(6.2\ x\ 10^{-4}\ m^2)}{2\pi(0.05\ m)}[/tex]
L = 0.863 x 10⁻³ H = 0.863 mH
B.
The self-induced emf is given by the following formula:
[tex]E=L\frac{\Delta I}{\Delta t}\\\\[/tex]
where,
E = self-induced emf = ?
ΔI = change in current = 2 A
Δt = change in time = 3 ms = 0.003 s
Therefore,
[tex]E=(0.000863\ H)\frac{2\ A}{0.003\ s}[/tex]
E = 0.58 volts
C.
According to Lenz's Law, the direction of the induced emf always opposes the change in flux that causes it. Hence, the direction of the induced emf will be from b to a.
Learn more about Lenz's Law here:
https://brainly.com/question/12876458?referrer=searchResults
A string of holiday lights has 15 bulbs with equal resistances. If one of the bulbs
is removed, the other bulbs still glow. But when the entire string of bulbs is
connected to a 120-V outlet, the current through the bulbs is 5.0 A. What is the
resistance of each bulb?
Answer:
Resistance of each bulb = 360 ohms
Explanation:
Let each bulb have a resistance r .
Since, even after removing one of the bulbs, the circuit is closed and the other bulbs glow. Therfore, the bulbs are connected in Parallel connection.
[tex] \frac{1}{r(equivalent)} = \frac{1}{r1} + \frac{1}{r2} + + + + \frac{1}{r15} [/tex]
[tex] \frac{1}{r(equivalent)} = \frac{15}{r} [/tex]
R(equivalent) = r/15
Now, As per Ohms Law :
V = I * R(equivalent)
120 V = 5 A * r/15
r = 360 ohms
hat a 15 kg body is pulled along a horizontal fictional table by a force of 4N what is the acceleration of the body
Answer:
Acceleration of the body is:
[tex]a=0.27\,\,m/s^2[/tex]
Explanation:
Use Newton's second Law to solve for the acceleration:
[tex]F=m\,\,a\\a=\frac{F}{m} \\a=\frac{4\,N}{15\,\,kg} \\a=0.27\,\,m/s^2[/tex]
Warm blooded animals are homeothermic; that is, they maintain an approximately constant body temperature. (Forhumans it's about 37 oC.) When they are in an environment that is below their optimum temperature, they use energy derived from chemical reactions within their bodies to warm them up. One of the ways that animals lose energy to their environment is through radiation. Every object emits electromagnetic radiation that depends on its temperature. For very hot objects like the sun, that radiation is visible light. For cooler objects, like a house or a person, that radiation is in the infrared and is invisible. Nonetheless, it still carries energy. Other ways that energy is lost by a warm animal to a cool environment includes conduction (direct touching of a cooler object) and convection (cooler air moving and carrying thermal energy away). See Heat Transfer for a discussion of all three.
For this problem, we'll just consider how much energy an animal needs to burn (obtain from internal chemical reactions) in order to stay warm just from radiation losses. The rate at which an object loses energy through radiation is given by the Stefan-Boltzmann equation:
Rate of energy loss = AεσT4
where T is the absolute (Kelvin) temperature, A is the area of the object, ε is the emissivity (unitless and =1 for a perfect emitter, less for anything else), and σ is the Stefan-Boltzmann constant:
σ = 5.67 x 10-8 J/(s m2 K4)
Consider a patient trying to sleep naked in a cool room (55 oF = 13 oC). Assume that the person being considered is a perfect emitter and absorber of radiation (ε = 1), has a surface area of about 2.5 m2, and a mass of 80 kg.
a. A person emits thermal radiation at a rate corresponding to a temperature of 37 oC and absorbs radiation at a rate (from the air and walls) corresponding to a temperature of 13 oC. Calculate the individual's net rate of energy loss due to radiation (in Watts = Joules/second).
net rate of energy loss = Watts
b. Assume the patient produces no energy to keep warm. If they have a specific heat about equal to that of water (1 Cal/kg-oC) how much would their temperature fall in one hour? (1 Cal = 1kcal = 103 cal)
ΔT = oC
c. Given that the energy density of fat is about 9 Cal/g, how many grams of fat would the person have to utilize to maintain their body temperature in that environment for one hour?
amount of fat needed = g
Answer:
a) 360.7 J/s
b) 16.23 °C
c) 34.48 g
Explanation:
The mass of the person = 80 kg
The person is a perfect emitter, ε = 1
surface area of the person = 2.5 m^2
a) If he emits radiation at 37 °C, [tex]T_{out}[/tex] = 37 + 273 = 310 K
and receives radiation at 13 °C, [tex]T_{in}[/tex] = 13 + 273 = 286 K
Rate of energy loss E = Aεσ([tex]T^{4} _{out}[/tex] - [tex]T^{4} _{in}[/tex] )
where σ = 5.67 x 10^-8 J/(s m^2 K^4)
substituting values, we have
E = 2.5 x 1 x 5.67 x 10^-8 x ([tex]310^{4}[/tex] - [tex]286^{4}[/tex]) = 360.7 J/s
b) If they have specific heat about equal to that of water = 1 Cal/kg-°C
but 1 Cal = 1 kcal = 10^3 cal
specific heat of person is therefore = 10^3 cal/kg-°C
heat loss = 360.7 J/s = 360.7 x 3600 = 1298520 J/hr
heat lost in 1 hour = 1 x 1298520 = 1298520 J
This heat lost = mcΔT
where ΔT is the temperature fall
m is the mass
c is the specific heat equivalent to that of water
the specific heat is then = 10^3 cal/kg-°C
equating, we have
1298520 = 80 x 10^3 x ΔT
1298520 = 80000ΔT
ΔT = 1298520/80000 = 16.23 °C
c) 1298520 J = 1298520/4184 = 310.35 Cal
density of fat = 9 Cal/g
gram of fat = 310.35/9 = 34.48 g
A lamp in a child's Halloween costume flashes based on an RC discharge of a capacitor through its resistance. The effective duration of the flash is 0.220 s, during which it produces an average 0.520 W from an average 3.00 V.
A. How much charge moves through the lamp (C)?
B. Find the capacitance (F).
C. What is the resitance of the lamo?
Answer:
A. 0.0374C
B. 0.012F
C. 18 ohms
Explanation:
See attached file
A load of 1 kW takes a current of 5 A from a 230 V supply. Calculate the power factor.
Answer:
Power factor = 0.87 (Approx)
Explanation:
Given:
Load = 1 Kw = 1000 watt
Current (I) = 5 A
Supply (V) = 230 V
Find:
Power factor.
Computation:
Power factor = watts / (V)(I)
Power factor = 1,000 / (230)(5)
Power factor = 1,000 / (1,150)
Power factor = 0.8695
Power factor = 0.87 (Approx)
Two waves are traveling in the same direction along a stretched string. The waves are 45.0° out of phase. Each wave has an amplitude of 7.00 cm. Find the amplitude of the resultant wave.
Answer:
The amplitude of the resultant wave is 12.93 cm.
Explanation:
The amplitude of resultant of two waves, y₁ and y₂, is given as;
Y = y₁ + y₂
Let y₁ = A sin(kx - ωt)
Since the wave is out phase by φ, y₂ is given as;
y₂ = A sin(kx - ωt + φ)
Y = y₁ + y₂ = 2A Cos (φ / 2)sin(kx - ωt + φ/2 )
Given;
phase difference, φ = 45°
Amplitude, A = 7.00 cm
Y = 2(7) Cos (45 /2) sin(kx - ωt + 22.5° )
Y = 12.93 cm
Therefore, the amplitude of the resultant wave is 12.93 cm.
Which of
of
these
following material is
used as fuse material?
carbon,
silver
Copper
Aluminium
The provided question is not correct as, there is more than one options are correct, however the explaining every correct option -
Answer:
The correct answer are - silver, copper and aluminium all three used as fuse material.
Explanation:
A safety device in any electric circuit of that prevents the electric system in case of short circuit by breaking the connection of electric system or circuit termed as the Fuse or fuse element. Normally the fuse are made up of wire or element of material that are low in melting point and high in resistance.
Zinc, lead, tin, silver, copper, aluminium, and alloy of tin and alloy are used as fuse element or material for their low melting point and high resistance these are easily breaks the electric path in case of short circuit.
Find the average magnitude of the induced emf if the change in shape occurs in 0.125 ss and the local 0.504-TT magnetic field is perpendicular to the plane of the loop.
Complete Question
An emf is induced in a conducting loop of wire 1.12m long as its shape is.
changed from square to circular. Find the average magnitude of the induced emf if the change in shape occurs in 0.125 ss and the local 0.504-TT magnetic field is perpendicular to the plane of the loop.
Answer:
The induced emf is [tex]\epsilon = 0.0863 \ V[/tex]
Explanation:
From the question we are told that
The time taken is [tex]\Delta t = 0.125 \ s[/tex]
The magnitude of the magnetic field is B = 0.504 T
The length of the loop wire is [tex]l = 1.12 \ m[/tex]
Generally the circumference of the wire when in circular form is
[tex]C = 2 \pi r[/tex]
=> [tex]l = 2 \pi r[/tex]
=> [tex]r =[/tex][tex]\frac{l}{2 \pi}[/tex]
=> [tex]r =[/tex][tex]\frac{1.12}{2 * 3.142}[/tex]
=> [tex]r =[/tex][tex]0.1782 \ m[/tex]
Now the area of the wire as a circle is
[tex]A = \pi r^2[/tex]
=> [tex]A = 3.142 * (0.1782)^2[/tex]
=> [tex]A = 0.0998 \ m^2[/tex]
The length of one side of the square is
[tex]b = \frac{l}{4}[/tex]
[tex]b = \frac{1.12}{4}[/tex]
[tex]b = 0.28 \ m[/tex]
Now the area of the wire as a square is
[tex]A_s = b^2[/tex]
=> [tex]A_s =(0.28 )^2[/tex]
[tex]A_s = 0.0784 \ m^2[/tex]
Generally the induced emf is mathematically represented as
[tex]\epsilon = \frac{B * [A - A_s ]}{\Delta t }[/tex]
=> [tex]\epsilon = \frac{0.504 * [0.0998 - 0.0784 ]}{0.125 }[/tex]
=> [tex]\epsilon = 0.0863 \ V[/tex]
A horizontal circular platform rotates counterclockwise about its axis at the rate of 0.945 rad/s. You, with a mass of 69.7 kg, walk clockwise around the platform along its edge at the speed of 1.01 m/s with respect to the platform. Your 20.7 kg poodle also walks clockwise around the platform, but along a circle at half the platform's radius and at half your linear speed with respect to the platform. Your 17.7 kg mutt, on the other hand, sits still on the platform at a position that is 3/4 of the platform's radius from the center. Model the platform as a uniform disk with mass 93.1 kg and radius 1.93 m. Calculate the total angular momentum of the system.
Answer:
317.22
Explanation:
Given
Circular platform rotates ccw 93.1kg, radius 1.93 m, 0.945 rad/s
You 69.7kg, cw 1.01m/s, at r
Poodle 20.2 kg, cw 1.01/2 m/s, at r/2
Mutt 17.7 kg, 3r/4
You
Relative
ω = v/r
= 1.01/1.93
= 0.522
Actual
ω = 0.945 - 0.522
= 0.42
I = mr^2
= 69.7*1.93^2
= 259.6
L = Iω
= 259.6*0.42
= 109.4
Poodle
Relative
ω = (1.01/2)/(1.93/2)
= 0.5233
Actual
ω = 0.945- 0.5233
= 0.4217
I = m(r/2)^2
= 20.2*(1.93/2)^2
= 18.81
L = Iω
= 18.81*0.4217
= 7.93
Mutt
Actual
ω = 0.945
I = m(3r/4)^2
= 17.7(3*1.93/4)^2
= 37.08
L = Iω
= 37.08*0.945
= 35.04
Disk
I = mr^2/2
= 93.1(1.93)^2/2
= 173.39
L = Iω
= 173.39*0.945
= 163.85
Total
L = 109.4+ 7.93+ 36.04+ 163.85
= 317.22 kg m^2/s
A wire of 5.8m long, 2mm diameter carries 750ma current when 22mv potential difference is applied at its ends. if drift speed of electrons is found then:_________.
(a) The resistance R of the wire(b) The resistivity p, and(c) The number n of free electrons per unit volume.
Explanation:
According to Ohms Law :
V = I * R
(A) R (Resistance) = 0.022 / 0.75 = 0.03 Ohms
Also,
[tex]r = \alpha \frac{length}{area} = \alpha \frac{5.8}{3.14 \times 0.001 \times 0.001} [/tex]
(B)
[tex] \alpha(resistivity) = 1.62 \times {10}^{ - 8} [/tex]
Drift speed is missing. It is given as;
1.7 × 10^(-5) m/s
A) R = 0.0293 ohms
B) ρ = 1.589 × 10^(-8)
C) n = 8.8 × 10^(28) electrons
This is about finding, resistance and resistivity.
We are given;Length; L = 5.8 m
Diameter; d = 2mm = 0.002 m
Radius; r = d/2 = 0.001 m
Voltage; V = 22 mv = 0.022 V
Current; I = 750 mA = 0.75 A
Area; A = πr² = 0.001²π
Drift speed; v_d = 1.7 × 10^(-5) m/s
A) Formula for resistance is;R = V/I
R = 0.022/0.75
R = 0.0293 ohms
B) formula for resistivity is given by;ρ = RA/L
ρ = (0.0293 × 0.001²π)/5.8
ρ = 1.589 × 10^(-8)
C) Formula for current density is given by;J = n•e•v_d
Where;
J = I/A = 0.75/0.001²π A/m² = 238732.44 A/m²
e is charge on an electron = 1.6 × 10^(-19) C
v_d = 1.7 × 10^(-5) m/s
n is number of free electrons per unit volume
Thus;
238732.44 = n(1.6 × 10^(-19) × 1.7 × 10^(-5))
238732.44 = (2.72 × 10^(-24))n
n = 238732.44/(2.72 × 10^(-24))
n = 8.8 × 10^(28)
Read more at; brainly.com/question/17005119
If 50 mL of each of the liquids in the answer choices were poured into a 250 mL beaker, which layer would be directly above a small rubber ball with a density of 0.960 g/mL? A. sea water – density of 1.024 g/mL B. mineral oil – density of 0.910 g/mL C. distilled water – density of 1.0 g/mL D. petroleum oil – density of 0.820 g/mL
Answer:
B. mineral oil – density of 0.910 g/mL.
Explanation:
Hello,
In this case, since the density is known as the degree of compactness a body has (mass in the occupied volume), the higher the density, the higher the weight of the body, therefore, if submerged into a liquid it could float if less dense than the liquid or sink if more dense than the liquid.
In such a way, since the rubber is more dense than mineral (0.960 g/mL > 0.910 g/mL) oil but less dense than distilled water (0.960 g/mL < 1.0 g/mL) we can say that B. mineral oil – density of 0.910 g/mL is directly above it when submerged.
Best regards.
What will be the nature of the image formed from both a convex lens and a concave
lens of 20 centimeter focus distance, when the object is placed at a distance of
10 centimeters?
Answer:
Explanation:
Using the lens formula
1//f = 1/u+1/v
f is the focal length of the lens
u is the object distance
v is the image distance
For convex lens
The focal length of a convex lens is positive and the image distance can either be negative or positive.
Given f = 20cm and u = 10cm
1/v = 1/f - 1/u
1/v = 1/20-1/10
1/v = (1-2)/20
1/V = -1/20
v = -20/1
v = -20 cm
Since the image distance is negative, this shows that the nature of the image formed by the convex lens is a virtual image
For concave lens
The focal length of a concave lens is negative and the image distance is negative.
Given f = -20cm and u = 10cm
1/v = 1/f - 1/u
1/v = -1/20-1/10
1/v = (-1-2)/20
1/V = -3/20
v = -20/3
v = -6.67 cm
Since the image distance is negative, this shows that the nature of the image formed by the concave lens is a virtual image
Helium-neon laser light (λ = 6.33 × 10−7 m) is sent through a 0.30 mm-wide single slit. What is the width of the central maximum on a screen 1.0 m from the slit?
Answer:
The width is [tex]w_c = 0.00422 \ m[/tex]
Explanation:
From the question we are told that
The wavelength is [tex]\lambda = 6.33*10^{-7} \ m[/tex]
The width of the slit is [tex]d = 0.3\ mm = 0.3 *10^{-3} \ m[/tex]
The distance of the screen is [tex]D = 1.0 \ m[/tex]
Generally the central maximum is mathematically represented as
[tex]w_c = 2 * y[/tex]
Here y is the width of the first order maxima which is mathematically represented as
[tex]y = \frac{\lambda * D}{d}[/tex]
substituting values
[tex]y = \frac{6.33*10^{-7} * 1.0}{ 0.30}[/tex]
[tex]y = 0.00211 \ m[/tex]
So
[tex]w_c = 2 *0.00211[/tex]
[tex]w_c = 0.00422 \ m[/tex]
In a double‑slit interference experiment, the wavelength is lambda=487 nm , the slit separation is d=0.200 mm , and the screen is D=48.0 cm away from the slits. What is the linear distance Δx between the eighth order maximum and the fourth order maximum on the screen?
Answer:
Δx = 4.68 x 10⁻³ m = 4.68 mm
Explanation:
The distance between the consecutive maxima, in Young's Double Slit Experiment is given bu the following formula:
Δx = λD/d
So, the distance between the eighth order maximum and the fourth order maximum on the screen will be given as:
Δx = 4λD/d
where,
Δx = distance between eighth order maximum and fourth order maximum=?
λ = wavelength = 487 nm = 4.87 x 10⁻⁷ m
d = slit separation = 0.2 mm = 2 x 10⁻⁴ m
D = Distance between slits and screen = 48 cm = 0.48 m
Therefore,
Δx = (4)(4.87 x 10⁻⁷ m)(0.48 m)/(2 x 10⁻⁴ m)
Δx = 4.68 x 10⁻³ m = 4.68 mm
The four wheels of a car are connected to the car's body by spring assemblies that let the wheels move up and down over bumps and dips in the road. When a 68 kg (about 150 lb) person sits on the left front fender of a small car, this corner of the car dips by about 1.2 cm (about 1/2 in).
If we treat the spring assembly as a single spring, what is the approximate spring constant?
k= ____________
Answer:
The approximate spring constant is [tex]k = 55533.33 \ N/m[/tex]
Explanation:
From the question we are told that
The mass of the person is [tex]m = 68 \ kg[/tex]
The dip of the car is [tex]x = 1.2 \ cm = 0.012 \ m[/tex]
Generally according to hooks law
[tex]F = k * x[/tex]
here the force F is the weight of the person which is mathematically represented as
[tex]F = m * g[/tex]
=> [tex]m * g = k * x[/tex]
=> [tex]k = \frac{m * g }{x }[/tex]
=> [tex]k = \frac{68 * 9.8}{ 0.012}[/tex]
=> [tex]k = 55533.33 \ N/m[/tex]
An object on a level surface experiences a horizontal force of 12.7 N due to kinetic friction. The coefficient of kinetic friction is 0.42.
What is the mass of the object? (Express your answer to two significant figures)kg
Answer:
The mass of the object is 3.08 kg.
Explanation:
The horizontal force is12.7 N and the coefficient of the kinetic fraction are 0.42. Now we have to compute the mass of the object. Thus, use the below formula to find the mass of the object.
Let the mass of the object = m.
The coefficient of kinetic friction, n = 0.42
Therefore,
Force, F = n × mg
12.7 = 0.42 × 9.8 × m
m = 3.08 kg
The mass of the object is 3.08 kg.
How much energy is required to accelerate a spaceship with a rest mass of 121 metric tons to a speed of 0.509 c?
Answer
1.07E22 Joules
Explanation;
We know that mass expands by a factor
=>>1/√[1-(v/c)²]
But v= 0.509c
So
1/√(1 - 0.509²)
=>>> 1/√(1 - 0.2591)
= >> 1/√(0.7409) = 1.16
But given that 121 tons is rest mass so 121- 1.16= 119.84 tons is kinetic energy
And we know that rest mass-energy equivalence is 9 x 10^19 joules per ton.
So Multiplying by 119.84
Kinetic energy will be 1.07x 10^22 joules
A major strike-slip earthquake on the San Andreas fault in California will cause a catastrophic tsunami affecting residents of San Francisco.
a) true
b) false
Answer:
a) true
Explanation:
The san andres is a transform fault that forms boundary between the Pacific and the North Atlantic plate and this slip strike is characterized by the latex motion the fault runs in the length of the California state. This plate is widely estimated for the high magnitude of earthquakes and varies from 7.7 to 8.3 magnitude. They are capable of producing a deadly tsunami that can devastate the pacific northwest.Air flows through a converging-diverging nozzle/diffuser. A normal shock stands in the diverging section of the nozzle. Assuming isentropic flow, air as an ideal gas, and constant specific heats determine the state at several locations in the system. Solve using equations rather than with the tables.
Answer:
HELLO your question has some missing parts below are the missing parts
note: The specific heat ratio and gas constant for air are given as k=1.4 and R=0.287 kJ/kg-K respectively.
--Given Values--
Inlet Temperature: T1 (K) = 325
Inlet pressure: P1 (kPa) = 560
Inlet Velocity: V1 (m/s) = 97
Throat Area: A (cm^2) = 5.3
Pressure upstream of (before) shock: Px (kPa) = 207.2
Mach number at exit: M = 0.1
Answer: A) match number at inlet = 0.2683
B) stagnation temperature at inlet = 329.68 k
C) stagnation pressure = 588.73 kPa
D) ) Throat temperature = 274.73 k
Explanation:
Determining states at several locations in the system
A) match number at inlet
= V1 / C1 = 97/ 261.427 = 0.2683
C1 = sound velocity at inlet = [tex]\sqrt{K*R*T}[/tex] = [tex]\sqrt{1.4 *0.287*10^3}[/tex] = 361.427 m/s
v1 = inlet velocity = 97
B) stagnation temperature at inlet
= T1 + [tex]\frac{V1 ^2}{2Cp}[/tex] = 325 + [tex]\frac{97^2}{2 * 1.005*10^{-3} }[/tex]
stagnation temperature = 329.68 k
C) stagnation pressure
= [tex]p1 ( 1 + 0.2Ma^2 )^{3.5}[/tex]
Ma = match number at inlet = 0.2683
p1 = inlet pressure = 560
hence stagnation pressure = 588.73 kPa
D) Throat temperature
= [tex]\frac{Th}{T} = \frac{2}{k+1}[/tex]
Th = throat temperature
T = stagnation temp at inlet = 329.68 k
k = 1.4
make Th subject of the relation
Th = 329.68 * (2 / 2.4 ) = 274.73 k
During the spin cycle of your clothes washer, the tub rotates at a steady angular velocity of 31.7 rad/s. Find the angular displacement Δθ of the tub during a spin of 98.3 s, expressed both in radians and in revolutions.
Answer:
[tex]\Delta \theta = 3116.11\,rad[/tex] and [tex]\Delta \theta = 495.944\,rev[/tex]
Explanation:
The tub rotates at constant speed and the kinematic formula to describe the change in angular displacement ([tex]\Delta \theta[/tex]), measured in radians, is:
[tex]\Delta \theta = \omega \cdot \Delta t[/tex]
Where:
[tex]\omega[/tex] - Steady angular speed, measured in radians per second.
[tex]\Delta t[/tex] - Time, measured in seconds.
If [tex]\omega = 31.7\,\frac{rad}{s}[/tex] and [tex]\Delta t = 98.3\,s[/tex], then:
[tex]\Delta \theta = \left(31.7\,\frac{rad}{s} \right)\cdot (98.3\,s)[/tex]
[tex]\Delta \theta = 3116.11\,rad[/tex]
The change in angular displacement, measured in revolutions, is given by the following expression:
[tex]\Delta \theta = (3116.11\,rad)\cdot \left(\frac{1}{2\pi} \frac{rev}{rad} \right)[/tex]
[tex]\Delta \theta = 495.944\,rev[/tex]
A 70 kg man floats in freshwater with 3.2% of his volume above water when his lungs are empty, and 4.85% of his volume above water when his lungs are full.
Required:
a. Calculate the volume of air he inhales - called his lung capacity - in liters.
b. Does this lung volume seem reasonable?
Answer:
Explanation:
A) Vair = 1.3 L
B) Volume is not reasonable
Explanation:
A)
Assume
m to be total mass of the man
mp be the mass of the man that pulled out of the water
m1 be the mass above the water with the empty lung
m2 be the mass above the water with full lung
wp be the weight that the buoyant force opposes as a result of the air.
Va be the volume of air inside man's lungs
Fb be the buoyant force due to the air in the lung
given;
m = 78.5 kg
m1 = 3.2% × 78.5 = 2.5 kg
m2 = 4.85% × 78.5 = 3.8kg
But, mp = m2- m1
mp = 3.8 - 2.5
mp = 1.3kg
So using
Archimedes principle, the relation for formula for buoyant force as;
Fb = (m_displaced water)g = (ρ_water × V_air × g)
Where ρ_water is density of water = 1000 kg/m³
Thus;
Fb = wp = 1.3× 9.81
Fb = 12.7N
But
Fb = (ρ_water × V_air × g)
So
Vair = Fb/(ρ_water × × g)
Vair = 12.7/(1000 × 9.81)
V_air = 1.3 × 10^(-3) m³
convert to litres
1 m³ = 1000 L
Thus;
V_air = 1.3× 10^(-3) × 1000
V_air = 1.3 L
But since the average lung capacity of an adult human being is about 6-7litres of air.
Thus, the calculated lung volume is not reasonable
Explanation:
UVC light used in sterilizers, has wavelengths between 100 to 280 nm. If a certain UVC wave has a wavelength of 142.9 nm, what is the energy of one of its photons in J
Answer:
The energy of one of its photons is 1.391 x 10⁻¹⁸ J
Explanation:
Given;
wavelength of the UVC light, λ = 142.9 nm = 142.9 x 10⁻⁹ m
The energy of one photon of the UVC light is given by;
E = hf
where;
h is Planck's constant = 6.626 x 10⁻³⁴ J/s
f is frequency of the light
f = c / λ
where;
c is speed of light = 3 x 10⁸ m/s
λ is wavelength
substitute in the value of f into the main equation;
E = hf
[tex]E = \frac{hc}{\lambda} \\\\E = \frac{6.626*10^{-34} *3*10^{8}}{142.9*10^{-9}} \\\\E = 1.391*10^{-18} \ J[/tex]
Therefore, the energy of one of its photons is 1.391 x 10⁻¹⁸ J
g One of the harmonics in an open-closed tube has frequency of 500 Hz. The next harmonic has a frequency of 700 Hz. Assume that the speed of sound in this problem is 340 m/s. a. What is the length of the tube
Answer:
The length of the tube is 85 cm
Explanation:
Given;
speed of sound, v = 340 m/s
first harmonic of open-closed tube is given by;
N----->A , L= λ/₄
λ₁ = 4L
v = Fλ
F = v / λ
F₁ = v/4L
Second harmonic of open-closed tube is given by;
L = N-----N + N-----A, L = (³/₄)λ
[tex]\lambda = \frac{4L}{3}\\\\ F= \frac{v}{\lambda}\\\\F_2 = \frac{3v}{4L}[/tex]
Third harmonic of open-closed tube is given by;
L = N------N + N-----N + N-----A, L = (⁵/₄)λ
[tex]\lambda = \frac{4L}{5}\\\\ F= \frac{v}{\lambda}\\\\F_3 = \frac{5v}{4L}[/tex]
The difference between second harmonic and first harmonic;
[tex]F_2 -F_1 = \frac{3v}{4L} - \frac{v}{4L}\\\\F_2 -F_1 = \frac{2v}{4L} \\\\F_2 -F_1 =\frac{v}{2L}[/tex]
The difference between third harmonic and second harmonic;
[tex]F_3 -F_2 = \frac{5v}{4L} - \frac{3v}{4L}\\\\F_3 -F_2 = \frac{2v}{4L} \\\\F_3 -F_2 =\frac{v}{2L}[/tex]
Thus, the difference between successive harmonic of open-closed tube is
v / 2L.
[tex]700H_z- 500H_z= \frac{v}{2L} \\\\200 = \frac{v}{2L}\\\\L = \frac{v}{2*200} \\\\L = \frac{340}{2*200}\\\\L = 0.85 \ m\\\\L = 85 \ cm[/tex]
Therefore, the length of the tube is 85 cm
Sammy is 5 feet and 5.3 inches tall. What is Sammy's height in inches?
Answer:
[tex]\boxed{\sf 65.3 \ inches}[/tex]
Explanation:
1 foot = 12 inches
Sammy is 5 feet tall.
5 feet = ? inches
Multiply the feet value by 12 to find in inches.
5 × 12
= 60
Add 5.3 inches to 60 inches.
60 + 5.3
= 65.3
Suppose a 500 mb chart valid today at 12 Z indicates a large trough over the eastern US and a large ridge over the western US. An aircraft, flying in the vicinity of 18,000 ft altitude from west to east over the US at 12 Z today, will _____ altitude if the altimeter is not corrected. Group of answer choices
Answer:
An aircraft, flying in the vicinity of 18,000 ft altitude from west to east over the US at 12 Z today, will __LOSE___ altitude if the altimeter is not corrected
A 25 cm diameter circular saw blade spins at 3500 rpm. How fast would you have to push a straight hand saw to have the teeth move through the wood at the same rate as the circular saw teeth
Answer:
The answer is "45.79 m/s"
Explanation:
Given values:
diameter= 25 cm
w= 3500 rpm
Formula:
[tex]\boxed{v=w \times r} \ \ \ \ \ \ _{where} \ \ \ w = \frac{rad}{s} \ \ \ and \ \ \ r = meters[/tex]
Calculating r:
[tex]r= \frac{diameter}{2}[/tex]
[tex]=\frac{25}{2}\\\\=12.5 \ cm[/tex]
converting value into meters: [tex]12.5 \times 10^{-2} \ \ meter[/tex]
calculating w:
[tex]w= diameter \times \frac{2\pi}{60}\\[/tex]
[tex]= 3500 \times \frac{2\times 3.14}{60}\\\\= 3500 \times \frac{2\times 314}{6000}\\\\= 35 \times \frac{314}{30}\\\\= 35 \times \frac{314}{30}\\\\=\frac{10990}{30}\\\\=\frac{1099}{3}\\\\=366.33[/tex]
w= 366.33 [tex]\ \ \frac{rad}{s}[/tex]
Calculating v:
[tex]v= w\times r\\[/tex]
[tex]= 366.33 \times 12.5 \times 10^{-2}\\\\= 366.33 \times 12.5 \times 10^{-2}\\\\= 4579.125 \times 10^{-2}\\\\\boxed{=45.79 \ \ \frac{m}{s}}[/tex]
If two identical wires carrying a certain current in the same direction are placed parallel to each other, they will experience a force of repulsion.
a) true
b) false
Answer:
The answer is B. falseExplanation:
Current in the same direction
When current flow through to parallel conductors of a given length, when the current flows in the same direction
1. A force of attraction between the wires occurs and this tends to draw the wires inward
2. A magnetic field in the same direction is produced.
Current in opposite direction
when the current is in opposite direction
1. Force of repulsion between the two wires occurs, draws the wire outward
2. A magnetic field in opposite direction occurs
