Which of the following happens to a molecule of an object when the object is heated? (1 point)

Answers

Answer 1

Answer:

They get more energy, so they vibrate!

Explanation:


Related Questions

Typical "hard" water contains about 2.0 x 10–3 mol of Ca2+ per liter. Calculate the maximum concentration of fluoride ion that could be present in hard water. Assume fluoride is the only anion present that will precipitate calcium ion.

Answers

Answer:

[tex][F^-]_{max}=4x10{-3}\frac{molF^-}{L}[/tex]

Explanation:

Hello,

In this case, for the described situation, we infer that calcium reacts with fluoride ions to yield insoluble calcium fluoride as shown below:

[tex]Ca^{+2}(aq)+2F^-(aq)\rightleftharpoons CaF_2(s)[/tex]

Which is typically an equilibrium reaction, since calcium fluoride is able to come back to the ions. In such a way, since the maximum amount is computed via stoichiometry, we can see a 1:2 mole ratio between the ions, therefore, the required maximum amount of fluoride ions in the "hard" water (assuming no other ions) turns out:

[tex][F^-]_{max}=2.0x10^{-3}\frac{molCa^{2+}}{L}*\frac{2molF^-}{1molCa^{2+}} \\[/tex]

[tex][F^-]_{max}=4x10{-3}\frac{molF^-}{L}[/tex]

Best regards.

How many kg/hr of steam are produced by a 50HP boiler?

Answers

Answer:

Explanation:

50 HP = 50 x 746 watt

= 37300 watt

= 37300 J /s

heat produced in one hour = 60 x 60 x 37300 J

= 134280 x 10³ J

latent heat of vaporization = 2260 x 10³ J / kg .

for evaporation of water of mass 1 kg , 2260 x 10³ J of heat is required .

kg of water being evaporated by boiler per hour

= 134280 x 10³ / 2260 x 10³

= 59.41 kg

rate of production of steam

= 59.41 kg / hr .

During which phase do the centromeres split, allowing the two linked chromatids to separate?

Answers

Answer:

Anaphase

Explanation:

The centromere splits during the anaphase of the cell division. Thus, allowing the two linked chromatids to separate.

A typical chromosome is made up of two sister chromatids joined together by a structure known as the centromere. During cell division - at the metaphase stage - the chromosomes align at the equator of the cell, forming the metaphase plate. The spindle from the opposing ends of the cell engages each chromosome at the kinetochore of the centromere.

At the anaphase stage, the centromere splits, leading to the separation of the sister chromatids of each chromosome. The sister chromatids of the same then start migrating in the opposite direction as a result of the shortening of the spindle fiber.

Methanol liquid burns readily in air. One way to represent this equilibrium is: 2 CO2(g) + 4 H2O(g)2 CH3OH(l) + 3 O2(g) We could also write this reaction three other ways, listed below. The equilibrium constants for all of the reactions are related. Write the equilibrium constant for each new reaction in terms of K, the equilibrium constant for the reaction above. 1) CH3OH(l) + 3/2 O2(g) CO2(g) + 2 H2O(g) K1 = 2) CO2(g) + 2 H2O(g) CH3OH(l) + 3/2 O2(g) K2 = 3) 2 CH3OH(l) + 3 O2(g) 2 CO2(g) + 4 H2O(g)

Answers

Answer:

Answers are in the explanation

Explanation:

It is possible to obtain K of equilibrium of related reactions knowing the laws:

A + B ⇄ C K₁

C ⇄ A + B K = 1 /K₁

The inverse reaction has the inverse K equilibrium

2A + 2B ⇄ 2C K = K₁²

The multiplication of the coefficients of reaction produce a k powered to the number you are multiplying the coefficients

For the reaction:

2 CO2(g) + 4 H2O(g) ⇄ 2 CH3OH(l) + 3 O2(g) K

1) CH3OH(l) + 3/2 O2(g) ⇄ CO2(g) + 2 H2O(g)

This is the inverse reaction but also the coefficients are dividing in the half, that means:

[tex]K_1 = \frac{1}{k^{1/2}} = (1/K)^{1/2}[/tex]

2) CO2(g) + 2 H2O(g) ⇄ CH3OH(l) + 3/2 O2(g)

Here,the only change is the coefficients are the half of the original reaction:

[tex]K_2 = K^{1/2}[/tex]

3) 2CH3OH(l) + 3 O2(g) ⇄ 2 CO2(g) + 4 H2O(g)

This is the inverse reaction. Thus, you have the inverse K of equilibrium:

[tex]K_3 = \frac{1}{K}[/tex]

Calculate ΔS∘rxn for the balanced chemical equation 2H2S(g)+3O2(g)→2H2O(g)+2SO2(g) Express the entropy change to four significant figures and include the appropriate units.

Answers

Answer:

-170.65

188.8+ 256.8-205.8-(2x205.2)

-170.65 is the entropy change.

What is Entropy Change?

Entropy trade is the phenomenon that is the measure of change of disorder or randomness in a thermodynamic gadget. It is associated with the conversion of heat or enthalpy completed in work. A thermodynamic device that has extra randomness means it has high entropy.

Subtract the sum of the absolute entropies of the reactants from the sum of the absolute entropies of the products, each extended by using their suitable stoichiometric coefficients, to reap ΔS° for the reaction.

Learn more about entropy change here: https://brainly.com/question/14257064

#SPJ2

A microwave oven heats by radiating food with microwave radiation, which is absorbed by the food and converted to heat. If the radiation wavelength is 12.5 cm, how many photons of this radiation would be required to heat a container with 0.250 L of water from a temperature of 20.0oC to a temperature of 99oC

Answers

Answer:

The total photons required for this radiation = 5.1938 × 10²⁸ photons

Explanation:

Given that:

A microwave oven heats by radiating food with microwave radiation, which is absorbed by the food and converted to heat.

If the radiation wavelength is 12.5 cm,

density of water = 1g/cm³

volume of the container = 0.250 L = 250 cm³

density = mass/volume

mass of the water = density × volume

mass of the water =  1g/cm³  × 250 cm³

mass of the water = 250 g

specific heat capacity of water = 4.182 J/g°C

The change in temperature was from 20.0° C to 99° C

ΔT =( 99 -20.0)° C

ΔT = 79.0° C

The heat absorbed in the process is calculated by using the formula,

q = mcΔT

q = 250 g × 4.182 J/g°C ×  79.0° C

q = 82594.5 Joules

Recall that the radiation wavelength λ = 12.5 cm = 0.125 m

The amount of energy of one photon of the radiation wavelength is determined by using the formula:

E = hv  

since v = c/λ

E = hc/λ

where;

h = Planck's constant = 6.626 × 10⁻³⁴ J.s

c = velocity of light = 3.0 × 10⁸ m/s

E = (6.626 × 10⁻³⁴ J.s × 3.0 × 10⁸ m/s)/ 0.125 m

E = 1.59024⁻²⁴ Joules

The total photons required for this radiation = total heat energy/energy of radiation

The total photons required for this radiation = 82594.5 Joules/1.59024⁻²⁴ Joules

The total photons required for this radiation = 5.1938 × 10²⁸ photons

Which part of an atom is mostly empty space?
A. nucleus
B. proton cloud
C. electron cloud
D. neutron

Answers

Answer:

C. Electron cloud

the electron is around 1/2000 times the size of the proton.

If you imagine the proton a a marble in the middle of a football field, the electrons will revolve around the last row

Zinc is used as a coating for steel to protect the steel from environmental corrosion. If a piece of steel is submerged in an electrolysis bath for 24 minutes with a current of 6.5 Amps, how many grams of zinc will be plated out? The molecular weight of Zn is 65.38, and Zn+2 + 2e– → Zn. Question 7 options: A) 3.17 g of Zn B) 1.09 g of Zn C) 6.34 g of Zn D) 12.68 g of Zn

Answers

Answer:

A) 3.17 g of Zn

Explanation:

Let's consider the reduction of Zn(II) that occurs in an electrolysis bath.

Zn⁺²(aq) + 2e⁻ → Zn(s)

We can establish the following relations:

1 min = 60 s1 A = 1 C/sThe charge of 1 mole of electrons is 96,468 C (Faraday's constant).When 2 moles of electrons circulate, 1 mole of Zn is deposited.The molar mass of Zn is 65.38 g/mol

The mass of Zn deposited under these conditions is:

[tex]24min \times \frac{60s}{1min} \times \frac{6.5C}{s} \times \frac{1mol\ e^{-} }{96,468C} \times \frac{1molZn}{2mol\ e^{-}} \times \frac{65.38g}{1molZn} = 3.17 g[/tex]

Answer:

A.) 3.17

Explanation:

I got it right in class!

Hope this Helps!! :))

The solubility of calcium oxalate, CaC2O4, in pure water is 4.8 × 10‑5 moles per liter. Cal­culate the value of Ksp for silver carbonate from this data.

Answers

Answer:

2.3 × 10⁻⁹

Explanation:

Step 1: Write the reaction for the solution of calcium oxalate

CaC₂O₄(s) ⇄ Ca²⁺(aq) + C₂O₄²⁻(aq)

Step 2: Make an ICE chart

We can relate the molar solubility (S) with the solubility product constant (Ksp) through an ICE chart.

        CaC₂O₄(s) ⇄ Ca²⁺(aq) + C₂O₄²⁻(aq)

I                                0                 0

C                              +S               +S

E                                S                 S

The solubility product constant is:

Ksp = [Ca²⁺] × [C₂O₄²⁻] = S² = (4.8 × 10⁻⁵)² = 2.3 × 10⁻⁹

The substance formed on addition of water to an aldehyde or ketone is called a hydrate or a/an:_______
A) vicinal diol
B) geminal diol
C) acetal
D) ketal

Answers

Answer:

B) geminal diol

Explanation:

Hello,

In this case, considering the attached picture, you can see that the substance resulting from the hydrolysis of an aldehyde or a ketone is a geminal diol since the two hydroxyl groups are in the same carbon. Such hydrolysis could be carried out in either acidic or basic conditions depending upon the equilibrium constant.

Regards.

At a certain temperature the equilibrium constant, Kc, equals 0.110 for the reaction: 2 ICl (g) ⇌ I2 (g) +Cl2 (g) What is the equilibrium concentration of ICl if 0.750 mol of I2 and 0.750 mol of Cl2 are initially mixed in a 1.00-L flask?

Answers

Answer:

The equilibrium concentration of ICl is 2.26 M

Explanation:

Chemical equilibrium is a state in which no changes are observed as time passes, despite the fact that the substances present continue to react. This is because chemical equilibrium is established when the forward and reverse reaction take place simultaneously at the same rate.

For the study of chemical equilibrium, the so-called equilibrium constant Kc is useful. Being:

aA + bB ⇔ cC + dD

the equilibrium constant Kc is:

[tex]Kc=\frac{[C]^{c} *[D]^{d} }{[A]^{a}*[B]^{b} }[/tex]

That is, the constant Kc is equal to the multiplication of the concentrations of the products raised to their stoichiometric coefficients by the multiplication of the concentrations of the reactants also raised to their stoichiometric coefficients.

For the reaction:

2 ICl (g) ⇌ I₂ (g) +Cl₂ (g)

the constant Kc is:

[tex]Kc=\frac{[I_{2} ]*[Cl_{2} ]}{[ICl]^{2} }[/tex]

Being Kc =0.110 and the concentration being the amount of moles of solute that appear dissolved in each liter of the mixture and being calculated by dividing the moles of the solute by the liters of the solution:

[tex][I_{2} ]=\frac{0.750 moles}{1 L} =0.750 \frac{moles}{L}[/tex][tex][Cl_{2} ]=\frac{0.750 moles}{1 L} =0.750 \frac{moles}{L}[/tex]

and replacing in the constant we get:

[tex]0.110=\frac{0.750*0.750}{[ICl]^{2} }[/tex]

Solving, you get the ICl concentration at equilibrium:

[tex][ICl]^{2} =\frac{0.750*0.750}{0.110 }[/tex]

[tex][ICl] =\sqrt{\frac{0.750*0.750}{0.110 }}[/tex]

[ICl]= 2.26 M

The equilibrium concentration of ICl is 2.26 M



If you have 2.4L of SO2 gas (at STP) how many moles of sulfur dioxide do you have?

Answers

Answer:

0.107 mole of SO2.

Explanation:

1 mole of a gas occupy 22.4 L at standard temperature and pressure (STP).

With the above information, we can simply calculate the number of mole of SO2 that will occupy 2.4 L at STP.

This can be obtained as follow:

22.4 L contains 1 mole of SO2.

Therefore, 2.4 L will contain = 2.4/22.4 = 0.107 mole of SO2.

Therefore, 0.107 mole of SO2 is present in 2.4 L at STP.

what is the colour before and after when bromine reacts with chlorine ??​

Answers

ANSWER

I need great answers

EXPLANATION

please rate my answer as great

Calculate the pH of a solution formed by mixing 250.0 mL of 0.15 M NH4Cl with 200.0 mL of 0.12 M NH3. The Kb for NH3 is 1.8 × 10-5.

Answers

Answer:

The pH of the solution is 9.06.

Explanation:

The reaction of the dissociation of NH₃ in water is:

NH₃(aq) + H₂O(l)  ⇄  NH₄⁺(aq) + OH⁻(aq)     (1)

[NH₃] - x                     [NH₄⁺] + x     x  

The concentration of NH₃ and NH₄⁺ is:

[tex] [NH_{3}] = \frac{n_{NH_{3}}}{V_{T}} = \frac{C_{i}_{(NH_{3})}*Vi_{NH_{3}}}{V_{NH_{3}} + V_{NH_{4}^{+}}} = \frac{0.12 M*0.2 L}{0.2 L + 0.25 L} = 0.053 M [/tex]

[tex] [NH_{4}^{+}] = \frac{C_{i}_{(NH_{4}^{+})*V_{NH_{4}^{+}}}}{V_{NH_{3}} + V_{NH_{4}^{+}}} = \frac{0.15 M*0.25 L}{0.2 L + 0.25 L} = 0.083 M [/tex]

From equation (1) we have:

[tex]Kb = \frac{[NH_{4}^{+}][OH^{-}]}{[NH_{3}]}[/tex]

[tex] 1.8 \cdot 10^{-5} = \frac{(0.083 + x)*x}{0.053 - x} [/tex]

[tex] 1.8 \cdot 10^{-5}(0.053 - x) - (0.083 + x)*x = 0 [/tex]

By solving the above equation for x we have:

x =  1.15x10⁻⁵ = [OH⁻]

The pH of the solution is:

[tex] pOH = -log([OH^{-}]) = -log(1.15 \cdot 10^{-5}) = 4.94 [/tex]

[tex] pH = 14 - pOH = 14 - 4.94 = 9.06 [/tex]

Therefore, the pH of the solution is 9.06.

I hope it helps you!

A chemist prepares a solution of sodium chloride by measuring out 25.4 grams of sodium chloride into a 100. mL volumetric flask and filling the flask to the mark with water. Calculate the concentration in mol/L of the chemist's sodium chloride solution. Be sure your answer has the correct number of significant digits.

Answers

Answer:

The concentration in mol/L =  4.342 mol/L

Explanation:

Given that :

mass of sodium chloride = 25.4 grams

Volume of the volumetric flask = 100 mL

We all know that the molar mass of sodium chloride NaCl = 58.5 g/mol

and number of moles = mass/molar mass

The number of moles of sodium chloride = 25.4 g/58.5 g/mol

The number of moles of sodium chloride = 0.434188 mol

The concentration in mol/L = number of mol/ volume of the solution

The concentration in mol/L = 0.434188 mol/ 100 × 10⁻³ L

The concentration in mol/L =  4.34188 mol/L

The concentration in mol/L =  4.342 mol/L

plsssss help!!! Deep Space 1 was a spacecraft powered by an engine that gave off xenon particles to change velocity. It had a mass of 500 kg. Which expression can be used to find the spacecraft’s acceleration if its engine created a net force of 0.10 N? A) 0.10 N 500 kg B) 500 kg · 0.10 N C) 500 kg 0.10 N D) 500 kg + 0.10 N

Answers

Answer:

Spacecraft’s acceleration (a) = 0.10 N / 500 kg

Explanation:

Given:

Mass of Spacecraft (M) = 500 Kg

Force generate by engine (F) = 0.10 N

Find:

Spacecraft’s acceleration (a)

Computation:

F = Ma

0.10 = 500 (a)

a = 0.10 / 500

Spacecraft’s acceleration (a) = 0.10 N / 500 kg

The expression which can be used to find the spacecraft’s acceleration if its engine created a net force of 0.10 N is  0.10 N/500Kg.

We know that force is the product of the mass a body and its acceleration. The result of motion is the action of an unbalanced force. We have the following information;

Mass of the spacecraft = 500 kg

Force on the engine =  0.10 N

From Newton's law;

F = ma

F = force

m = mass

a = acceleration

a = F/m

acceleration = 0.10 N/500Kg

Learn more: https://brainly.com/question/8592296

Find the density if the volume is 15 mL and the mass is 8.6 g. (5 pts)
Find the volume if the density is 2.6 g/mL and the mass is 9.7 g.(5 pts)
Find the mass if the density is 1.6 g/cm3 and the volume is 4.1 cm3 (5 pts)
Find the density if the initial volume of water is 12.8 mL, the final volume is 24.6 mL and the mass of the object is 4.3 g. Make a drawing to show the water displacement using a graduated cylinder. (gdoc, gdraw)

Answers

Answer:

[tex]\large \boxed{\text{0.57 g/mL; 3.7 mL; 6.6 g; 0.366 g/mL}}[/tex]

Explanation:

1. Density from mass and volume

[tex]\text{Density} = \dfrac{\text{mass}}{\text{volume}}\\\\\rho = \dfrac{m}{V}\\\\\rho = \dfrac{\text{8.6 g}}{\text{15 mL}} = \text{0.57 g/mL}\\\text{The density is $\large \boxed{\textbf{0.57 g/mL}}$}[/tex]

2. Volume from density and mass

[tex]V = \text{9.7 g}\times\dfrac{\text{1 mL}}{\text{2.6 g}} = \text{3.7 mL}\\\\\text{The volume is $\large \boxed{\textbf{3.7 mL}}$}[/tex]

3. Mass from density and volume

[tex]\text{Mass} = \text{4.1 cm}^{3} \times \dfrac{\text{1.6 g}}{\text{1 cm}^{3}} = \textbf{6.6 g}\\\\\text{The mass is $\large \boxed{\textbf{6.6 g}}$}[/tex]

4. Density by displacement

Volume of water + object = 24.6 mL

Volume of water                = 12.8 mL

Volume of object               = 11.8 mL

[tex]\rho = \dfrac{\text{4.3 g}}{\text{11.8 mL}} = \text{0.36 g/mL}\\\text{The density is $\large \boxed{\textbf{0.36 g/mL}}$}[/tex]

Your drawing showing water displacement using a graduated cylinder should resemble the figure below.

 

For a sample of stomach acid that is 2.02×10−2 M in HCl, how many moles of HCl are in 14.6 mL of the stomach acid?

Answers

Answer:

0.0002949 moles

Explanation:

Concentration = 2.02×10−2 M

Volume = 14.6 mL = 0.0146 L (Upon converting to litres)

Number of moles = ?

These variables are related by the fllowing equation;

Concentration = Number of moles / Volume

Number of moles = Concentration * Volume

Number of moles = 2.02×10−2 * 0.0146 = 0.0002949 moles

Which gas will have the most collisions between its particles?

Answers

Answer:

The gas is Methane at 340K

Aqueous ammonia is added to a mixture of silver chloride and water. Given that Kf for the reaction between Ag+ and NH3 is large, which of the following are true?
A) The free ions are favored over the complex ion.
B) The complex ion is favored over solid silver chloride.
C) The free Ag+ ion is unstable.
D) More silver chloride will precipitate.

Answers

Answer:

B) The complex ion is favored over solid silver chloride

C) The free Ag+ ion is unstable.

Explanation:

Hello,

In this case, since the dissociation of solid silver chloride occurs at equilibrium with a neglectable solubility product (very small Ksp), which means that the solid tends to remain undissolved:

[tex]AgCl(s)\rightleftharpoons Ag^+(aq)+Cl^-(aq)[/tex]

By the addition of ammonia, the following reaction is favored:

[tex]Ag^+(aq)+2NH_3(aq)\rightleftharpoons [Ag(NH_3)_2]^+(aq)[/tex]

Which has a large equilibrium constant, which means that the formation of the complex is assured. In such a way, by addition of more ammonia, more complex will be formed, therefore B) The complex ion is favored over solid silver chloride is true. Moreover, C) The free Ag+ ion is unstable, since they tend to form the complex once they are formed by the solid silver chloride so it readily reacts.

Best regards.

If 11.2 g of naphthalene, C10H8, is dissolved in 107.8 g of chloroform, CHCl3, what is the molality of the solution

Answers

Answer:

CHC12

Explanation:

i am not really sure i am onna do a quick research 4 u tho

For an ideal gas condition, what is the mass (g) of N2 if the pressure is 2.0 atm, the volume is 25 mL and the temperature is 290 Kelvin.

Answers

Answer:

THE MASS OF NITROGEN GAS IN THIS CONDITIONS IS 0.0589 g

Explanation:

In an ideal condition

PV = nRT or PV = MRT/ MM where:

M = mass = unknown

MM =molar mass = 28 g/mol

P = pressure = 2 atm

V = volume = 25 mL = 0.025 L

R = gas constant = 0.082 L atm/mol K

T = temperature = 290 K

n = number of moles

The gas in the question is nitrogen gas

Molar mass of nitrogen gas = 14 * 2 = 28 g/mol

Then equating the variables and solving for M, we have

M = PV MM/ RT

M = 2 * 0.025 * 28 / 0.082 * 290

M = 1.4 / 23.78

M = 0.0589 g

The mass of the nitrogen gas at ideal conditions of 2 atm, 25 mL volume and 290 K temperature is 0.0589 g

The electrolysis of molten AlCl 3 for 2.50 hr with an electrical current of 15.0 A produces ________ g of aluminum metal.

Answers

Can we actually get more information

The mole is a counting number that allows scientists to describe how individual molecules and atoms react. If one mole of atoms or molecules is equal to 6.022 x 10^32 atoms or molecules, how many molecules are in 23.45 g sample of copper (II) hydroxide, Cu(OH)2? Express your answer to the correct number of significant figures. (MM of Cu(OH)2 is 97.562g/mol. Be sure to show all steps completed to arrive at the answer.

Answers

Answer:

[tex]\large \boxed{1.503 \times 10^{23}\text{ molecules of Cu(OH)}_{2}}$}[/tex]

Explanation:

You must calculate the moles of Cu(OH)₂, then convert to molecules of Cu(OH)₂.

1. Moles of Cu(OH)₂[tex]\text{Moles of Cu(OH)}_{2} = \text{24.35 g Cu(OH)}_{2} \times \dfrac{\text{1 mol Cu(OH)}_{2}}{\text{97.562 g Cu(OH)}_{2}} = \text{0.2496 mol Cu(OH)}_{2}[/tex]

2. Molecules of Cu(OH)₂[tex]\text{No. of molecules} = \text{0.2496 mol Cu(OH)}_{2} \times \dfrac{6.022 \times 10^{23}\text{ molecules Cu(OH)}_{2}}{\text{1 mol Cu(OH)}_{2}}\\\\= \mathbf{1.503 \times 10^{23}}\textbf{ molecules Cu(OH)}_{2}\\\text{There are $\large \boxed{\mathbf{1.503 \times 10^{23}}\textbf{ molecules of Cu(OH)}_{2}}$}[/tex]

The number of molecules of copper (II) hydroxide in 23.45 g sample has been [tex]\rm \bold {1.45\;\times\;10^2^3}[/tex].

According to the Avogadro number, the number of molecules in a mole of atom has been equivalent to the Avogadro constant. The value of Avogadro constant has been [tex]\rm 6.023\;\times\;10^2^3[/tex].

The moles of a compound has been given as:

[tex]\rm Moles=\dfrac{Mass}{Molar\;mass}[/tex]

The moles in 23.45 g copper (II) hydroxide has been:

[tex]\rm Moles=\dfrac{23.45}{97.562} \\Moles=0.24\;mol[/tex]

The moles of copper (II) hydroxide has been 0.24 mol.

The number of molecules in 0.24 mol sample has been driven by:

[tex]\rm 1\;mol=6.023\;\times\;10^2^3\;molecules\\0.24\;mol=0.24\;\times\;10^2^3\;molecules\\0.24\;mol=1.45\;\times\;10^2^3\;molecules[/tex]

The number of molecules of copper (II) hydroxide in 23.45 g sample has been [tex]\rm \bold {1.45\;\times\;10^2^3}[/tex].

For more information about molecules in a mole of sample, refer to the link:

https://brainly.com/question/24577356

Automotive air bags inflate when sodium azide decomposes explosively to its constituent elements: 2NaN3 (s) → 2Na (s) + 3N2 (g) How many grams of sodium azide are required to produce 30.5 g of nitroge

Answers

Answer:

NaN3 = 47.2 g

Explanation:

Given:

2 NaN3 ⇒ 2 Na  + 3 N2

Find:

Amount of NaN3

Computation:

N2 moles = Product of N2 / molar mass of N2

N2 moles =30.5/28

N2 moles = 1.0893

2NaN3 makes 3(N2 )

So,

NaN3 moles = (2/3) moles of N2  

NaN3 moles = ( 2/3) × 1.0893

NaN3 moles = = 0.7262

NaN3 mass = 0.7262 x 65

NaN3 = 47.2 g

Answer:

NaN3 = 47.2 g

Explanation:

Given:

2 NaN3 ⇒ 2 Na  + 3 N2

Find:

Amount of NaN3

Computation:

N2 moles = Product of N2 / molar mass of N2

N2 moles =30.5/28

N2 moles = 1.0893

2NaN3 makes 3(N2 )

So,

NaN3 moles = (2/3) moles of N2  

NaN3 moles = ( 2/3) × 1.0893

NaN3 moles = = 0.7262

NaN3 mass = 0.7262 x 65

NaN3 = 47.2 g

Explanation:

1.) A sample of neon gas at a pressure of 0.646 atm and a temperature of 242 °C, occupies a volume of 515 mL. If the gas is cooled at constant pressure until its volume is 407 mL, the temperature of the gas sample will be ________°C.
2.) A sample of argon gas at a pressure of 0.633 atm and a temperature of 261 °C, occupies a volume of 694 mL. If the gas is heated at constant pressure until its volume is 796 mL, the temperature of the gas sample will be___________°C.
3.) 0.962 mol sample of carbon dioxide gas at a temperature of 20.0 °C is found to occupy a volume of 21.5 liters. The pressure of this gas sample ismm ____________ Hg.

Answers

Answer:1 )T2=134°C   2) T2=339.48°C. 3)

P=817.59 mmHg.

Explanation:

1.Given ;

pressure, P1 of neon gas = 0.646 atm

temperature, T1 =242oC + 273=515oC

Volume, V1 =515ml

Volume V2= 407ml

temperature , T 2= ?

Solution;

And at constant pressure, the volume cools at V2=407 mL at T2=?

From ideal gas equation, PV=nRT

V/T=constant

therefore

V1/V2=T1/T2 = T2=(V2 xT1)/V1

T2=(407 mL x 515 K)/515 mL= 407K.

T2= 407K -273= 134°C.   recall 0°C=273 K)

2..Given ;

pressure, P1 of neon gas = 0.633 atm

temperature, T1 =261oC + 273=534oC

Volume, V1 =694ml

Volume V2= 796ml

temperature , T 2= ?

Solution;

And at constant pressure, the volume expands  at V2=796mL at T2=?

From ideal gas equation, PV=nRT

V/T=constant

therefore

V1/V2=T1/T2 = T2=(V2 xT1)/V1

T2=(796 mL x 534 K)/694mL= 612.48K.

T2= 612.48K -273= 339.48°C. recall 0°C=273 K

3

Given;

moles of CO2= n=0.962 mol,

temperature T=20°C=20+273 K =293 K,

volume V=21.5 L,

gas constant R at L·mmHg/mol·K= 62.3637 L mmHg mol^-1 K^-1

Using  ideal gas equation PV=nRT

P=nRT/V

P=(0.962 mol)x(62.3637mmHg mol^-1 K^-1)x(293 K)/(21.5L)

P=817.59 mmHg.

Ammonium phosphate is an important ingredient in many fertilizers. It can be made by reacting phosphoric acid with ammonia . What mass of ammonium phosphate is produced by the reaction of of ammonia?

Answers

Answer:

The mass of ammonium phosphate produced is 14.3g

Explanation:

Full question contains: "What mass of ammonium phosphate is produced by the reaction of 4.9g of ammonia"

Ammonium phosphate ((NH₄)₃PO₄) can be produced by the reaction of phosphoric acid (H₃PO₄) with ammonia (NH₃) as follows:

H₃PO₄ + 3NH₃ → (NH₄)₃PO₄

Where 1 mole of phosphoric acid reacts with 3 moles of ammonia producing 1 mole of ammonium phosphate.

To know how many grams of ammonium phosphate we need to find moles of ammonia that react, and, with the chemical equation we can find moles of ammonium phosphate and its mass as follows:

Moles ammonia (Molar mass: 17.031g/mol):

4.9g × (1mol / 17.031g) = 0.288 moles of ammonia you have in 4.9g

Moles of ammonium phosphate (149.09g/mol) and its mass:

As 0.288 moles of NH₃ are reacting and 3 moles of ammonia produce 1 mole of ammonium phosphate, moles produced are:

Moles (NH₄)₃PO₄:

0.288 moles NH₃ ₓ (1 mol (NH₄)₃PO₄  / 3 mol NH₃) = 0.0959 moles (NH₄)₃PO₄

These moles are, in grams:

0.0959 moles (NH₄)₃PO₄ ₓ (149.09g / mol) = 14.3g ammonium phosphate.

The mass of ammonium phosphate produced is 14.3g

clacium hydroxide is slightly soluable in water about 1 gram will dissolve in 1 liter what are the spectator ions in the reaction ions in the reaction of such a dilute solution of calcium hydroxide with hydrochloric acid

Answers

Answer:

Ca²⁺ and Cl⁻

Explanation:

In a chemical reaction, spectator ions are ions that are not involved in the reaction, that means are the same before and after the reaction.

In water, calcium hydroxide, Ca(OH)₂ is dissociated in Ca²⁺ and OH⁻. Also, hydrochloric acid, HCl, dissociates in H⁺ and Cl⁻. The reaction is:

Ca²⁺ + 2OH⁻ + 2H⁺ + 2Cl⁻ → 2H₂O + Ca²⁺ + 2Cl⁻

The ions that react are H⁺ and OH⁻ (Acid and base producing water)

And the ions that are not reacting, spectator ions, are:

Ca²⁺ and Cl⁻

Calculate the concentration of H3O+ in a solution that contains 5.5 × 10-5 M OH- at 25°C. Identify the solution as acidic, basic, or neutral.

Answers

Explanation:

To calculate [H3O+] in the solution we must first find the pH from the [ OH-]

That's

pH + pOH = 14

pH = 14 - pOH

To calculate the pOH we use the formula

pOH = - log [OH-]

And [OH-] = 5.5 × 10^-5 M

So we have

pOH = - log 5.5 × 10^ - 5

pOH = 4.26

Since we've found the pOH we can now find the pH

That's

pH = 14 - 4.26

pH = 9.74

Now we can find the concentration of H3O+ in the solution using the formula

pH = - log H3O+

9.74 = - log H3O+

Find the antilog of both sides

H3O+ = 1.8 × 10^ - 10 M

The solution is basic since it's pH lies in the basic region.

Hope this helps you

Amino acids can be synthesized by reductive amination. Draw the structure of the organic compound that you would use to synthesize serine.

Answers

Answer:

Following are the answer to this question:

Explanation:

For the reductive amination of its carbonyl group, amino acids could be synthesized by reducing ammunition, which can be synthesized in the given attachment file:

please find the attachment:

Other Questions
One way to punctuate a compound sentence correctly is to join the two independent clauses with a comma. a semicolon. a comma and a subordinating conjunction. a semicolon and a coordinating conjunction.Which contains an independent clause? Because the tragic fumble was scored by the visiting team in the last minute. When the player, in an extraordinary move, went charging down the field. As the uproar from the delirious fans exploded jubilantly through the stadium. While the team made their play, the frenzied crowd cheered them to victory. What information is needed to investigate and describe a region by its geographic characteristics? find the total area of the prism Select the correct answer.Which state of matter is highly compressible, is made of particles moving independently of each other, and is present in large quantities near Earths surface?A. solidB. liquidC. gasD. plasma The divine rights of kings is best described as a belief that According to the lecture video on building dynamic charts, which of the following Excel functions are used in the "Refers to:" formula in Name Manager? A) SUMIF B) COUNTIF C) OFFSET D) COUNT find the slope between (0, 6) and (-3,9) Currently Baldwin is paying a dividend of $1.10 (per share). If this dividend stayed the same, but the stock price rose by 10% what would be the dividend yield Anna hired Juan to act as her sales agent in her auto dealership. However, Anna has instructed Juan not to enter into any sales contracts before she has had a chance to review the transaction. One day, Juan entered into a sales contract with William without informing Anna first. Has Juan created a contract with William that is binding on Anna in this situation? what is the discriminant and how many solutions? Explain the major events in Lincolns presidency and his actions / impact on the Civil War if z and (z+50) are supplement of each other find the value of z If the product of two matrices is AB=1/-3/5 over 2/5/7, what are the dimensions of Matrix B if A is a 2x3 matrix? Solve the system by substitution.y = -2y =5x + 40 Kaliska is jumping rope. The vertical height of the center of her rope off the ground R(t)R(t)R, left parenthesis, t, right parenthesis (in \text{cm}cmstart text, c, m, end text) as a function of time ttt (in seconds) can be modeled by a sinusoidal expression of the form a\cdot\cos(b\cdot t)+dacos(bt)+da, dot, cosine, left parenthesis, b, dot, t, right parenthesis, plus, d. At t=0t=0t, equals, 0, when she starts jumping, her rope is 0\text{ cm}0 cm0, start text, space, c, m, end text off the ground, which is the minimum. After \dfrac{\pi}{12} 12 start fraction, pi, divided by, 12, end fraction seconds, it reaches a height of 60\text{ cm}60 cm60, start text, space, c, m, end text from the ground, which is half of its maximum height Please answer ASAP!!plssss please solve this fast. Can I have your number? Find the exact value of cos A in simplest radical form. Select the correct answer. Whats the significance to scientists of finding a new, unknown fossil? A. It allows scientists to formulate new theories. B. It enables scientists to better differentiate among the various species. C. It proves that theres an unlimited supply of fossils to be unearthed. D. It provides evidence of links between evolutionary species. E. It provides scientists with a reason to continue their research.