When a monochromatic light of wavelength 433 nm incident on a double slit of slit separation 6 µm, there are 5 interference fringes in its central maximum. How many interference fringes will be in the central maximum of a light of wavelength 632.9 nm for the same double slit?

Answer:

K.E = 5.53 eV = 8.85 x 10⁻¹⁹ J

Explanation:

First we calculate the energy of photon:

E = hc/λ

where,

E = Energy of Photon = ?

h = Plank's Constant = 6.626 x 10⁻³⁴ J.s

c = speed of light = 3 x 10⁸ m/s

λ = wavelength = 120 nm = 1.2 x 10⁻⁷ m

Therefore,

E = (6.626 x 10⁻³⁴ J.s)(3 x 10⁸ m/s)/(1.2 x 10⁻⁷ m)

E = (16.565 x 10⁻¹⁹ J)(1 eV/1.6 x 10⁻¹⁹ J)

E = 10.35 eV

Now, from Einstein's Photoelectric equation we know that:

Energy of Photon = Work Function + K.E of Electron

10.35 eV = 4.82 eV + K.E

K.E = 10.35 eV - 4.82 eV

K.E = 5.53 eV = 8.85 x 10⁻¹⁹ J

The maximum kinetic energy of the ejected photoelectrons will be "8.85 × 10⁻¹⁹ J".

According to the question,

Speed of light, c = 3 × 10⁸ m/s

Wavelength, λ = 120 nm or,

                        = 1.2 × 10⁻⁷ m

Plank's Constant, h = 6.626 × 10⁻³⁴ J.s

Now,

The energy of photon will be:

→ E = [tex]\frac{hc}{\lambda}[/tex]

By substituting the values,

     = [tex]\frac{6.626\times 10^{-34}\times 3\times 20^8}{1.2\times 10^{-7}}[/tex]

     = [tex]\frac{16.565\times 10^{-19}}{\frac{1 \ eV}{1.6\times 10^{-19}} }[/tex]

     = 10.35 eV

By using Einstein's Photoelectric equation,  

Energy of Photon = Work function + K.E

                   10.35 = 4.82 + K.E

                       K.E = 10.35 - 4.82

                             = 5.53 eV or,

                             = 8.85 × 10⁻¹⁹ J

Thus the response above is correct.

Find out more information about Kinetic energy here:

https://brainly.com/question/25959744

Answer:

(A). 1620 watt.

(B).0.8885.

Explanation:

So, we are given the following data or parameters or information which is going to assist or help us in solving this particular Question or problem. So, we have;

Current = 9.35A, direct current at a potential difference of 195 V, frequency of the inverter = 60 Hz alternating current, alternating current with Vmax = 166V and Imax = 19.5A.

(A). The rms power is produced by the inverter = (19.5 /2 ) × 166 = 1620 watt(approximately).

(B). the rms values to find the power efficiency Pout/Pin of the inverter.

P(in) = 195 × 9.35 = 1823.3 watt.

Thus, the rms values to find the power efficiency Pout/Pin of the inverter = 1620/1823.3 = 0.88852324146441793 = 0.8885.

Answer:

0.35 m³/s

Explanation:

When the pipe's depth is 0.4 m, the area of the circular segment is:

A = ½ R² (θ − sin θ)

The depth of the water is:

h = R (1 − cos(θ/2))

Solving for θ:

0.4 = 0.5 (1 − cos(θ/2))

0.8 = 1 − cos(θ/2)

cos(θ/2) = 0.2

θ/2 = acos(0.2)

θ = 2 acos(0.2)

θ ≈ 2.74 rad

The area is therefore:

A = ½ (0.5 m)² (2.74 − sin 2.74)

A = 0.338 m²

The cross-sectional area when the pipe is full is:

A = π (0.5 m)²

A = 0.785 m²

The flow velocity is constant:

v = v

Q / A = Q / A

(0.15 m³/s) / (0.338 m²) = Q / (0.785 m²)

Q = 0.35 m³/s

Answer:

Upper plate Q/3

Lower plate 2Q/3

Explanation:

See attached file

Answer:

Explanation:

The force experienced by the moving electron in the magnetic field is expressed as F = qvBsinθ where;

q is the charge on the electron

v is the velocity of the electron

B is the magnetic field strength

θ is the angle that the velocity of the electron make with the magnetic field.

Given parameters

F =  1.40*10⁻¹⁶ N

q = 1.6*10⁻¹⁹C

v = 3.94*10³m/s

B = 1.23T

Required

Angle that the velocity of the electron make with the magnetic field

Substituting the given parameters into the formula:

1.40*10⁻¹⁶ =  1.6*10⁻¹⁹ * 3.94*10³ * 1.23 * sinθ

1.40*10⁻¹⁶ = 7.75392 * 10⁻¹⁹⁺³sinθ

1.40*10⁻¹⁶ = 7.75392 * 10⁻¹⁶sinθ

sinθ = 1.40*10⁻¹⁶/7.75392 * 10⁻¹⁶

sinθ = 1.40/7.75392

sinθ = 0.1806

θ = sin⁻¹0.1806

θ₁ = 10.4⁰

Since sinθ is positive in the 1st and 2nd quadrant, θ₂ = 180-θ₁

θ₂ = 180-10.4

θ₂ = 169.6⁰

Hence, the angle that the velocity of the electron make with the magnetic field are 10.4⁰ and 169.6⁰

Answer:

your question answer is 22°

Answer:

TOTAL INTERNAL REFLECTION

Explanation:

Retraction is defined as the change in the direction of light rays as it moves from less dense medium to a denser medium.

For us to have a critical angle, the ray must be passing from the denser medium to the less dense medium. As the angle of refraction in the less dense medium is increasing, the angle of incidence in the less dense medium also increases. A point will reach when the refracted ray will be parallel to the interface i.e angle of refraction is 90°, the angle of incidence at this point is known as the critical angle. If the angle of refraction keeps increasing further, it will get to a point when the refracted ray becomes reflected into the denser medium. At this stage we say that the ray is internally reflected and this is the point when the angle of incidence is greater than the critical angle.

Hence it can be concluded that the process that occurs when the angle of incidence is greater than the critical angle is called TOTAL INTERNAL REFLECTION

Answer:

The movement of energy and matter in a system differs from one system to another. On the other hand, in open system both the matter and energy move into and out of the system. Therefore, matter and energy in a system naturally change over time will decrease in entropy.

Explanation:

Answer:

Decrease in entropy

Explanation:

Various systems which exist in nature possess energy and matter that move through these system continuously. The movement of energy and matter in a system differs from one system to another.

In a closed system for example, only energy flows in and out of the system while matter does not enter or leave the system.

On the other hand, in open system both the matter and energy move into and out of the system.

Answer:

she need to use 20 cm thick

Explanation:

given data

wants the attic insulated = R-30

purchased = 10 cm thick

solution

as per given we can say that

10 cm is for the R 15

but she want for R 30

so  

R 30 thickness = [tex]\frac{30}{15} \times 10[/tex]  

R 30 thickness = 20 cm

so she need to use 20 cm thick

Answer:

Atoms are the particles that all matter is made from. When two or more kinds of atoms combine, they form pure elements

The answer is option A

Answer:

its molecues

Explanation:

Answer:

E. Coefficient of linear expansion

Explanation:

Change in Velocity = final velocity - initial velocity

Change in velocity = 30km/h - (- 45km/h )

= 75 km/h due west

Answer:

Explanation:

Given data:

power rating of the heater P= 1010 W

voltage of the heater V= 115 volts

current taken by the heater I= ?

We can apply the power formula to solve for the current in the heater

i.e P= IV

Making I the current subject of formula we have

I= P/V

Substituting our given data into the expression for I we have

I=1010/115= 8.78 A

Answer:

The time taken is  [tex]\Delta t = 1.5 \ s[/tex]

Explanation:

From the question we are told that

   The mass of the ball is  [tex]m = 1.25 \ kg[/tex]

    The time taken to make the first complete revolution is  t= 3.60 s

    The displacement of the first complete revolution is  [tex]\theta = 1 rev = 2 \pi \ radian[/tex]

Generally the displacement for one  complete revolution is mathematically represented as

       [tex]\theta = w_i t + \frac{1}{2} * \alpha * t^2[/tex]

Now given that the stone started from rest [tex]w_i = 0 \ rad / s[/tex]

     [tex]2 \pi =0 + 0.5* \alpha *(3.60)^2[/tex]

     [tex]\alpha = 0.9698 \ s[/tex]

Now the displacement for two  complete revolution is

         [tex]\theta_2 = 2 * 2\pi[/tex]

         [tex]\theta_2 = 4\pi[/tex]

Generally the displacement for two complete revolution is mathematically represented as  

     [tex]4 \pi = 0 + 0.5 * 0.9698 * t^2[/tex]

=>   [tex]t^2 = 25.9187[/tex]

=>   [tex]t= 5.1 \ s[/tex]

So

 The  time taken to complete the next oscillation is mathematically evaluated as

     [tex]\Delta t = t_2 - t[/tex]

substituting values

      [tex]\Delta t = 5.1 - 3.60[/tex]

     [tex]\Delta t = 1.5 \ s[/tex]

The time for the ball to complete the next revolution is 1.5 s.

The given parameters;

The constant angular acceleration of the ball is calculated as follows;

[tex]\theta = \omega t \ + \ \frac{1}{2} \alpha t^2\\\\2\pi = 0 \ + \ 0.5(3.6)^2 \alpha\\\\2\pi = 6.48 \alpha \\\\\alpha = \frac{2 \pi }{6.48} \\\\\alpha = 0.97 \ rad/s^2[/tex]

The time to complete the next revolution is calculated as follows;

[tex]4\pi = 0 + \frac{1}{2} (0.97)t^2\\\\8\pi = 0.97t^2\\\\t^2 = \frac{8\pi }{0.97} \\\\t^2 = 25.91\\\\t = \sqrt{ 25.91} \\\\t = 5.1 \ s[/tex]

[tex]\Delta t = 5.1 \ s \ - \ 3.6 \ s \\\\\Delta t = 1.5 \ s[/tex]

Thus, the time for the ball to complete the next revolution is 1.5 s.

Learn more here:https://brainly.com/question/20738528

Answer:

0.99Hz

Explanation:

Using F= -mx ( spring force)

At equilibrium the gravitational force will be balanced by the spring force so mg= kx

K= mg/ 0.25 N/m

But

Frequency f= 1/2pi √g/0.25

Frequency is 0.99Hz

The block is pulled down slightly and released so, Frequency of oscillation is 3.15 Hz

What information do we have?

Length starched = 2.5 cm

F = Kx

We know that

F = mg

So,

mg = Kx

K/m = g/x

[tex]f=\frac{1}{2\pi}\sqrt{\frac{g}{x} }\\f=\frac{1}{2\pi}\sqrt{\frac{9.8}{0.025} }[/tex]

Frequency of oscillation = 3.15 Hz

Find out more information about 'Oscillation'.

https://brainly.com/question/16016711?referrer=searchResults

Answer:

50 cm long

When 35cm long wrench is compared to 50cm long wrench, we find that the 50cm long wrench produces more turning effect of force because it has longer distance between fulcrum and line of action of force. At conclusion, the more the turning effect of force the more it is easy to unscrew bolts.

Answer:

129900

Explanation:

Given that

Mass of the particle, m = 1 g = 1*10^-3 kg

Speed of the particle, u = ½c

Speed of light, c = 3*10^8

To solve this, we will use the formula

p = ymu, where

y = √[1 - (u²/c²)]

Let's solve for y, first. We have

y = √[1 - (1.5*10^8²/3*10^8²)]

y = √(1 - ½²)

y = √(1 - ¼)

y = √0.75

y = 0.8660, using our newly gotten y, we use it to solve the final equation

p = ymu

p = 0.866 * 1*10^-3 * 1.5*10^8

p = 129900 kgm/s

thus, we have found that the momentum of the particle is 129900 kgm/s

Answer:

se the principle of induction.

place the two metallic spheres together,  now we bring the positively charged bar closer to the first sphere.

The charge that was induced in the sphere is distributed as infirm as possible,

At this time I separate the spheres and move the bar away, by separating the spheres the excess positive

Explanation:

For this exercise we will use that the electric charge is not created, it is not destroyed and charges of the same sign repel.

Let's use the principle of induction. We place the two metallic spheres together, one in front of the other, now we bring the positively charged bar closer to the first sphere.

Here the positive charge of the bar repels the positive charge of the sphere, but as this is mocil it moves as far away as possible, until the negative charge that remains neutralizes the positive charge of the bar.

The charge that was induced in the sphere is distributed as infirm as possible, most of it in the furthest sphere, since the Coulomb force decreases.

At this time I separate the spheres and move the bar away, by separating the spheres the excess positive charge in the last sphere cannot be neutralized, therefore this sphere remains with a positive charge.

Answer:

T = 80√3 N ≈ 139 N

W = 160 N

Explanation:

Sum of forces on B in the x direction:

∑F = ma

80 N sin 60° − T sin 30° = 0

T = 80 N sin 60° / sin 30°

T = 80√3 N

T ≈ 139 N

Sum of forces on B in the y direction:

∑F = ma

80 N cos 60° + T cos 30° − W = 0

W = 80 N cos 60° + T cos 30°

W = 40 N + 120 N

W = 160 N

Answer:

There is no induced current on the coil.

Explanation:

Current is induced in a coil or a circuit, when there is a break of flux linkage. A break in flux linkage is caused by a changing magnetic field, and must be achieved by a relative motion between the coil and the magnet. Holding the magnet above the center of the coil will cause no changing magnetic filed since there is no relative motion between the coil and the magnet.

Answer:

A) 0.4 mA

B) 0.03 mA

Explanation:

Given that

voltage source, V = 120 V

to solve this question, we would be using the very basic Ohms Law, that voltage is proportional to the current and the resistance passing through the circuit, if temperature is constant.

mathematically, Ohms Law, V = IR

V = Voltage

I = Current

R = Resistance

from question a, we were given 300kΩ, substituting this value of resistance in the equation, we have

120 = I * 300*10^3 Ω

making I the subject of the formula,

I = 120 / 300000

I = 0.0004 A

I = 0.4 mA

Question said, currents above 10 mA causes involuntary muscle contraction, this current is way below 10 mA, so nothing happens.

B, we have Resistance, R = 4000kΩ

Substituting like in part A, we have

120 = I * 4000*10^3 Ω

I = 120 / 4000000

I = 0.00003 A

I = 0.03 mA

This also means nothing happens, because 0.03 mA is very much lesser compared to in the 10 mA

The current through a person will be:

a) 0.4 mA

b) 0.03 mA

Given:

Voltage, V = 120 V

It states that the voltage or potential difference between two points is directly proportional to the current or electricity passing through the resistance, and directly proportional to the resistance of the circuit.

Ohms Law, V = I*R

where,

V = Voltage

I = Current

R = Resistance

a)

Given: Resistance=  300kΩ

[tex]120 = I * 300*10^3 ohm\\\\I = 120 / 300000\\\\I = 0.0004 A[/tex]

Thus, current will be, I = 0.4 mA

b)

Given: R = 4000kΩ

[tex]120 = I * 4000*10^3 ohm\\\\I = 120 / 4000000\\\\I = 0.00003 A[/tex]

Thus, current will be, I = 0.03 mA

From calculations, we observe that nothing happens, because 0.03 mA is very much lesser compared to in the 10 mA.

Find more information about Current here:

brainly.com/question/24858512

Answer:

The distance is [tex]D = 2.6 \ m[/tex]

Explanation:

From the question we are told that

    The wavelength of the light is  [tex]\lambda = 476.1 \ nm = 476.1 *10^{-9} \ m[/tex]

      The  distance between the slit is  [tex]d = 0.29 \ mm = 0.29 *10^{-3} \ m[/tex]

       The  between the first and second dark fringes is  [tex]y = 4.2 \ mm = 4.2 *10^{-3} \ m[/tex]

Generally  fringe width is mathematically represented as

       [tex]y = \frac{\lambda * D }{d}[/tex]

Where D is the distance of the slit to the screen

   Hence

        [tex]D = \frac{y * d}{\lambda }[/tex]

substituting values

       [tex]D = \frac{ 4.2 *10^{-3} * 0.29 *10^{-3}}{ 476.1 *10^{-9} }[/tex]

        [tex]D = 2.6 \ m[/tex]

Explanation:

Using Equations of Motion :

[tex]s = ut + \frac{1}{2} g {t}^{2} [/tex]

Height = 0 * 4 + 4.9 * 16

Height = 78.4 m

Answer:

(a) 10 s

(b) 30 m/s

(c) 150 m

Explanation:

The motorist's position at time t is:

x = 15t

The officer's position at time t is:

x = ½ (3) t² = 1.5 t²

(a) When they have the same position, the time is:

15t = 1.5 t²

t = 0 or 10 s

(b) The officer's speed is:

v = 3t

v = 30 m/s

(c) The position is:

x = 15t = 150 m

Answer:

1) a block going down a slope

2) a) W = ΔU + ΔK + ΔE, b) W = ΔE, c)  W = ΔK, d) ΔU = ΔK

Explanation:

In this exercise you are asked to give an example of various types of systems

1) a system where work is transformed into internal energy is a system with friction, for example a block going down a slope in this case work is done during the descent, which is transformed in part kinetic energy, in part power energy and partly internal energy that is represented by an increase in the temperature of the block.

2)

a) rolling a ball uphill

In this case we have an increase in potential energy, if there is a change in speed, the kinetic energy also increases, if the change in speed is zero, there is no change in kinetic energy and there is a change in internal energy due to the stationary rec in the point of contact

 W = ΔU + ΔK + ΔE

b) in this system work is transformed into internal energy

      W = ΔE

c) There is no friction here, therefore the work is transformed into kinetic energy

    W = ΔK

d) if you assume that there is no friction with the air, the potential energy is transformed into kinetic energy

      ΔU = ΔK

Answer:

a)  A = 1.99 μm , b) λ = 0.4134 m , c)  v = 57.2 m / s , d)   s = - 1,946 nm ,

e)      v_max = 1,739 mm / s

Explanation:

A sound wave has the general expression

           s = s₀ sin (kx - wt)

where s is the displacement, s₀ the amplitude of the wave, k the wave vector and w the angular velocity, in this exercise the expression given is

           s = 1.99 sin (15.2 x - 869 t)

a) the amplitude of the wave is

        A = s₀

        A = 1.99 μm

b) wave spectrum is

      k = 2π /λ

in the equation k = 15.2 m⁻¹

      λ = 2π / k

      λ = 2π / 15.2

     λ = 0.4134 m

c) the speed of the wave is given by the relation

       v = λ f

angular velocity and frequency are related

       w = 2π f

        f = w / 2π

        f = 869 / 2π

        f = 138.3 Hz

        v = 0.4134 138.3

         v = 57.2 m / s

d) To find the instantaneous velocity, we substitute the given distance and time into the equation

       s = 1.99 sin (15.2 0.0509 - 869 2.94 10⁻³)

       s = 1.99 sin (0.77368 - 2.55486)

remember that trigonometry functions must be in radians

       s = 1.99 (-0.98895)

       s = - 1,946 nm

The negative sign indicates that it shifts to the left

e) the speed of the oscillating part is

           v = ds / dt)

           v = - s₀(-w) cos (kx -wt)

the maximum speed occurs when the cosines is 1

           v_maximo = s₀w

           v_maximum = 1.99 869

           v_maximo = 1739.31 μm / s

let's reduce to mm / s

          v_maxio = 1739.31 miuy / s (1 mm / 103 mu)

          v_max = 1,739 mm / s

a) A is = 1.99 μm , b) λ is = 0.4134 m , c) v is = 57.2 m / s , d) s is = - 1,946 nm, e) v_max is = 1,739 mm / s

When A sound wave has the general expression is:

Then, s = s₀ sin (kx - wt)

Now, where s is the displacement, Then, s₀ is the amplitude of the wave, k the wave vector, and w the angular velocity, Now, in this exercise the expression given is

s is = 1.99 sin (15.2 x - 869 t)

a) When the amplitude of the wave is

A is = s₀

Thus, A = 1.99 μm

b) When the wave spectrum is

k is = 2π /λ

Now, in the equation k = 15.2 m⁻¹

Then, λ = 2π / k

After that, λ = 2π / 15.2

Thus, λ = 0.4134 m

c) When the speed of the wave is given by the relation is:

Then, v = λ f

Now, the angular velocity and frequency are related is:

w is = 2π f

Then, f = w / 2π

After that, f = 869 / 2π

Now, f = 138.3 Hz

Then, v = 0.4134 138.3

Thus, v = 57.2 m / s

d) Now, To find the instantaneous velocity, When we substitute the given distance and time into the equation

Then, s = 1.99 sin (15.2 0.0509 - 869 2.94 10⁻³)

After that, s = 1.99 sin (0.77368 - 2.55486)

Then remember that trigonometry functions must be in radians

After that, s = 1.99 (-0.98895)

Thus, s = - 1,946 nm

When The negative sign indicates that it shifts to the left

e) When the speed of the oscillating part is

Then, v = ds / dt)

Now, v = - s₀(-w) cos (kx -wt)

When the maximum speed occurs when the cosines is 1

Then, v_maximo = s₀w

After that, v_maximum = 1.99 869

v_maximo = 1739.31 μm / s

Now, let's reduce to mm / s

Then, v_maxio = 1739.31 miuy / s (1 mm / 103 mu)

Therefore, v_max = 1,739 mm / s

Finf more informmation about Wavelength here:

https://brainly.com/question/6352445

Answer:

entropy

Explanation:

Answer:

The magnetic field is 0.0857 T.

Explanation:

The electrons orbit the magnetic field with a centripetal force equal to

F = [tex]\frac{mv^{2} }{r}[/tex]

also, the force on an electron in a magnetic field is gotten as

F = Bqv

equating this two equations give

[tex]\frac{mv^{2} }{r}[/tex] = Bqv

mv/r = Bq

where m is the mass of the electron = 9.11 x 10^-31 kg

v is the the linear speed of the electron

B is the magnetic field on the electron

r is the radius of the orbital movement

q is the charge on an electron = 1.602 x 10^-19 C

but, the linear speed v = ωr

where ω is the angular speed of the electron

substituting into equation above, we have

mωr/r = Bq

which reduces to

mω = Bq

finally, w know that the angular speed is related to the frequency of the electron by

ω = 2πf

we then finally have

2mπf = Bq

where f is the frequency emitted by the electron = 2.4 GHz = 2.4 x 10^9 Hz

substituting values into the equation, we have

2 x 9.11 x 10^-31 x 3.142 x 2.4 x 10^9 = B x 1.602 x 10^-19

B = (1.3734 x 10^-20)/(1.602 x 10^-19) = 0.0857 T

= 85.7 mT

Answer:

7.86×10⁻⁷ m

Explanation:

Using,

v = λf.................. Equation 1

Where v = velocity of electromagnetic wave, λ = wave length, f = frequency.

make λ the subject of the equation

λ = v/f............... Equation 2

Note: All electromagnetic  wave have the same speed which is 3×10⁸ m/s.

Given: f = 3.818×10¹⁴ Hz

Constant: v = 3×10⁸ m/s

Substitute these values into equation 2

λ  =  3×10⁸/3.818×10¹⁴

λ  = 7.86×10⁻⁷ m

Hence the wavelength of the electromagnetic radiation is  7.86×10⁻⁷ m

The wavelength of this electromagnetic radiation is equal to [tex]7.86 \times 10^{-7} \;meters[/tex]

Given the following data:

Scientific data:

Velocity of an electromagnetic radiation = [tex]3 \times 10^8\;m/s[/tex]

To determine the wavelength of this electromagnetic radiation:

Mathematically, the wavelength of an electromagnetic radiation is calculated by using the formula;

[tex]Wavelength = \frac{Speed }{frequency}[/tex]

Substituting the given parameters into the formula, we have;

[tex]Wavelength = \frac{3 \times 10^8}{3.818\times 10^{14}}[/tex]

Wavelength = [tex]7.86 \times 10^{-7} \;meters[/tex]

Read more wavelength on here: https://brainly.com/question/6352445

Explanation:

Pressure is the same for both plungers.

P = P

F / A = F / A

F / (¼ π d²) = F / (¼ π d²)

F / d² = F / d²

5 N / (0.05 m)² = F / (1 m)²

F = 2000 N

None of the options are correct.