What is the reason for the increase and decrease size of the moon and write down in a paragraph.

Answer:

[tex]v=1.24\times 10^8\ m/s[/tex]

Explanation:

Given that,

The refractive index of benzene is 2.419

We need to find the speed of light in benzene. The ratio of speed of light in vacuum to the speed of light in the medium equals the refractive index. So,

[tex]n=\dfrac{c}{v}\\\\v=\dfrac{c}{n}\\\\v=\dfrac{3\times 10^8}{2.419}\\\\v=1.24\times 10^8\ m/s[/tex]

So, the speed of light in bezene is [tex]1.24\times 10^8\ m/s[/tex].

Answer:

Power factor = 0.87 (Approx)

Explanation:

Given:

Load = 1 Kw = 1000 watt

Current (I) = 5 A

Supply (V) = 230 V

Find:

Power factor.

Computation:

Power factor = watts / (V)(I)

Power factor = 1,000 / (230)(5)

Power factor = 1,000 / (1,150)

Power factor = 0.8695

Power factor = 0.87 (Approx)

Answer:

a. to the west.

Explanation:

An electron in a magnetic field always experience a force that tends to change its direction of motion through the magnetic field. According to Lorentz left hand rule (which is the opposite of Lorentz right hand rule for a positive charge), the left hand is used to represent the motion of an electron in a magnetic field. Hold out the left hand with the fingers held out parallel to the palm, and the thumb held at right angle to the other fingers. If the thumb represents the motion of the electron though the field, and the other fingers represent the direction of the field, then the palm will push in the direction of the force on the particle.

In this case, if we point the thumb (which shows the direction we shot the electron) to the south (towards your body), with the palm (shows the direction of the force) facing up to the roof, then the fingers (the direction of the field) will point west.

Answer:

Explanation:

A) Vair = 1.3 L

B) Volume is not reasonable

Explanation:

A)

Assume

m to be total mass of the man

mp be the mass of the man that pulled out of the water

m1 be the mass above the water with the empty lung

m2 be the mass above the water with full lung

wp be the weight that the buoyant force opposes as a result of the air.

Va be the volume of air inside man's lungs

Fb be the buoyant force due to the air in the lung

given;

m = 78.5 kg

m1 = 3.2% × 78.5 = 2.5 kg

m2 = 4.85% × 78.5 = 3.8kg

But, mp = m2- m1

mp = 3.8 - 2.5

mp = 1.3kg

So using

Archimedes principle, the relation for formula for buoyant force as;

Fb = (m_displaced water)g = (ρ_water × V_air × g)

Where ρ_water is density of water = 1000 kg/m³

Thus;

Fb = wp = 1.3× 9.81

Fb = 12.7N

But

Fb = (ρ_water × V_air × g)

So

Vair = Fb/(ρ_water × × g)

Vair = 12.7/(1000 × 9.81)

V_air = 1.3 × 10^(-3) m³

convert to litres

1 m³ = 1000 L

Thus;

V_air = 1.3× 10^(-3) × 1000

V_air = 1.3 L

But since the average lung capacity of an adult human being is about 6-7litres of air.

Thus, the calculated lung volume is not reasonable

Explanation:

Answer:

Torque = 0.012 N.m

Explanation:

We are given;

Mass of wheel;m = 750 g = 0.75 kg

Radius of wheel;r = 25 cm = 0.25 m

Final angular velocity; ω_f = 0

Initial angular velocity; ω_i = 220 rpm

Time taken;t = 45 seconds

Converting 220 rpm to rad/s we have;

220 × 2π/60 = 22π/3 rad/s

Equation of rotational motion is;

ω_f = ω_i + αt

Where α is angular acceleration

Making α the subject, we have;

α = (ω_f - ω_i)/t

α = (0 - 22π/3)/45

α = -0.512 rad/s²

The formula for the Moment of inertia is given as;

I = ½mr²

I = (1/2) × 0.75 × 0.25²

I = 0.0234375 kg.m²

Formula for torque is;

Torque = Iα

For α, we will take the absolute value as the negative sign denotes decrease in acceleration.

Thus;

Torque = 0.0234375 × 0.512

Torque = 0.012 N.m

Answer:

ΔT = 1ºC , 2ºCand 3ºC

Explanation:

In this exercise they indicate the specific heat of lithium

let's calculate the temperature increase as a function of the heat introduced

          Q = m [tex]c_{e}[/tex] ΔT

          ΔT = Q / m c_{e}

calculate

 for Q = 3.5 J

         ΔT = 3.5 / (1 3.5)

         ΔT = 1ºC

For Q = 7.0 J

         ΔT = 7 / (1 3.5)

         ΔT = 2ºC

for Q = 10.5 J

         ΔD = 10.5 / (1 3.5)

         ΔT = 3ºC

we see that this is a straight line, see attached

Answer:

Check your router connections then restart your router.

Explanation:

Answer:

Check your router connections then restart your router.

Explanation:

Most internet access comes from routers so the problem is most likely the router.

Answer:

A. We have that radius r = 4.00m intensity I = 8.00 W/m^

total power = power/ Area ( 4πr2)= 8.00 w/m^2( 4π ( 4.00 m)2=1607.68 W

b) I = total power/ 4πr2= 8.00 W/m2 ( 4.00 m/ 9.5 m)2= 1.418 W/m2

c) E = total power x time= 1607 . 68 W x 1s= 1607.68 J

Answer:

total current = 12.417 A

so it will not fuse as current is less than 15 A

Explanation:

given data

toaster = 1140-W

blender = 270-W

lamp = 80-W

voltage = 120 V

solution

we know that current is express as

current = power ÷ voltage   ......................1

here voltage is same in all three device

so

current by toaster is

I = [tex]\frac{1140}{120}[/tex]

I = 9.5 A

and

current by blender

I = [tex]\frac{270}{120}[/tex]

I = 2.25 A

and

current by lamp is

I = [tex]\frac{80}{120}[/tex]

I = 0.667 A

so here device in parallel so

total current is = 9.5 A + 2.25 A + 0.667 A

total current = 12.417 A

so it will not fuse as current is less than 15 A

Answer:

The frequency will change by a factor of 0.4

Explanation:

T = 2(pi)*sqrt(L/g)

Since g(moon) = (1/6)g(earth), the period would change by sqrt[1/(1/6)] = sqrt(6) ~ 2.5 times longer on the moon. Since the period & frequency are inverses, the frequency would be 1/2.5 or 0.4 times shorter on the moon.

Answer:

63 cm

Explanation:

Mathematically;

The focal length of a double convex lens is given as;

1/f = (n-1)[1/R1 + 1/R2]

where n is the refractive index of the medium given as 1.52

R1 and R2 represents radius of curvature which are given as 60cm and 72cm respectively.

Plugging these values into the equation, we have:

1/f = (1.52-1)[1/60 + 1/72)

1/f = 0.0158

f = 1/0.0158

f = 63.29cm which is approximately 63cm

1. The ocean water collects back in the ocean.

2. Condensation is the process by which water vapor in the air is changed into liquid water. Condensation is crucial to the water cycle because it is responsible for the formation of clouds.

3. an excessive amount of water flowing from downslope along earths surface

4. A.Evaporation occurs when water is warmed by the sun.

5. The water returns into the ocean by the water cycle . It evaporates , then it condensates , then it participates ( Rains ) and then goes back into the ocean.

Hope this answer correct ✌️

Answer:

The dispersion is [tex]D = 2.01220 *10^{5} \ rad/m[/tex]

Explanation:

From the question we are told that

    The wavelength of the light is  [tex]\lambda = 550 \ = 550 *10^{-9} \ n[/tex]

    The width of the grating is[tex]k = 1\ cm = 0.01 \ m[/tex]

    The  number of slit is  N =  1000 slits

    The order of the maxima is  m =  2

Generally the spacing between the slit is mathematically represented as

         [tex]d = \frac{k}{N}[/tex]

substituting values

        [tex]d = \frac{ 0.01}{1000}[/tex]

       [tex]d = 1.0 *10^{-5} \ m[/tex]

Generally the condition for constructive interference is

       [tex]d\ sin(\theta ) = m * \lambda[/tex]

substituting values

      [tex]1.0 *10^{-5} sin (\theta) = 2 * 550 *10^{-9}[/tex]

       [tex]\theta = sin^{-1} [\frac{ 2 * 550 *10^{-9}}{ 1.0 *10^{-5}} ][/tex]

      [tex]\theta = 6.315^o[/tex]

Generally the dispersion is mathematically represented as

           [tex]D = \frac{ m }{d cos(\theta )}[/tex]

substituting values

          [tex]D = \frac{ 2 }{ 1.0 *10^{-5} cos(6.315 )}[/tex]

           [tex]D = 2.01220 *10^{5} \ rad/m[/tex]

Answer:

If the magnet is moved, the galvanometer needle will deflect, showing that current is flowing through the coil which will increase total induced electromotive force

Explanation:

galvanometer is an instrument that can detect and measure small current in an electrical circuit.

If the magnet is moved, the galvanometer needle will deflect, showing that current is flowing through the coil. If it is move in a way into the coil,the needle deflect in that way and if it move in another way, it will deflect in the other way.

The total induced emf is equal to the emf induced in each loop by the changing magnetic flux, then multiplied by the number of loops and an increase in the number of loops will cause increase in the total induced emf.

Answer:

Here,

v (final velocity) = 0

u (initial velocity) = u

a = ?

s = 1m

t = 0.4s

using the first equation of motion,

0 = u + 0.4a

= -0.4a = u

using the second equation of motion:

1 = 0.4u + 0.08a

from the bold equation

1 = 0.4(-0.4a) + 0.08a

1 = -0.16a + 0.08a

1 = -0.08a

a = -1/0.08

a = -100/8

a = -12.5 m/s/s

please make me brainly, i am 1 brainly away from the next rank

Answer:

(a) 1.47 x 10⁴ V/m

(b) 1.28 x 10⁻⁷C/m²

(c) 3.9 x 10⁻¹²F

(d) 9.75 x 10⁻¹¹C

Explanation:

(a) For a parallel plate capacitor, the electric field E between the plates is given by;

E = V / d               -----------(i)

Where;

V = potential difference applied to the plates

d = distance between these plates

From the question;

V = 25.0V

d = 1.70mm = 0.0017m

Substitute these values into equation (i) as follows;

E = 25.0 / 0.0017

E = 1.47 x 10⁴ V/m

(c) The capacitance of the capacitor is given by

C = Aε₀ / d

Where

C = capacitance

A = Area of the plates = 7.60cm² = 0.00076m²

ε₀ = permittivity of free space =  8.85 x 10⁻¹²F/m

d = 1.70mm = 0.0017m

C = 0.00076 x  8.85 x 10⁻¹² / 0.0017

C = 3.9 x 10⁻¹²F

(d) The charge, Q, on each plate can be found as follows;

Q = C V

Q =  3.9 x 10⁻¹² x 25.0

Q = 9.75 x 10⁻¹¹C

Now since we have found other quantities, it is way easier to find the surface charge density.

(b) The surface charge density, σ, is the ratio of the charge Q on each plate to the area A of the plates. i.e

σ = Q / A

σ = 9.75 x 10⁻¹¹ /  0.00076

σ = 1.28 x 10⁻⁷C/m²

Answer:

-0.24diopters

Explanation:

The lens is intended that makes an object at infinity appear to be 4.2 m away, so do=infinity, dI = - 4.2m (minus sign because image is on same side of lens as object)

So 1/do +1/di = 1/f

1/infinity + 1/-4.2 = 1/f

1/f = 1/-4.2 = -0.24diopters

Answer: her rotational kinetic energy increases

Answer:

The energy of one of its photons is 1.391 x 10⁻¹⁸ J

Explanation:

Given;

wavelength of the UVC light, λ = 142.9 nm = 142.9 x 10⁻⁹ m

The energy of one photon of the UVC light is given by;

E = hf

where;

h is Planck's constant = 6.626 x 10⁻³⁴ J/s

f is frequency of the light

f = c / λ

where;

c is speed of light = 3 x 10⁸ m/s

λ  is wavelength

substitute in the value of f into the main equation;

E = hf

[tex]E = \frac{hc}{\lambda} \\\\E = \frac{6.626*10^{-34} *3*10^{8}}{142.9*10^{-9}} \\\\E = 1.391*10^{-18} \ J[/tex]

Therefore, the energy of one of its photons is 1.391 x 10⁻¹⁸ J

Answer: The correct answer for this question is letter (B) The electromagnetic waves reach Earth, while the mechanical waves do not. The sun generates both mechanical and electromagnetic waves. Space, between the sun and the earth is a nearly vacuum. So mechanical wave can not spread out in the vacuum.

Hope this helps!

Answer:

The electromagnetic waves reach Earth, while the mechanical waves do not

Answer:

Resistance of each bulb = 360 ohms

Explanation:

Let each bulb have a resistance r .

Since, even after removing one of the bulbs, the circuit is closed and the other bulbs glow. Therfore, the bulbs are connected in Parallel connection.

[tex] \frac{1}{r(equivalent)} = \frac{1}{r1} + \frac{1}{r2} + + + + \frac{1}{r15} [/tex]

[tex] \frac{1}{r(equivalent)} = \frac{15}{r} [/tex]

R(equivalent) = r/15

Now, As per Ohms Law :

V = I * R(equivalent)

120 V = 5 A * r/15

r = 360 ohms

Answer:

This means that mercury has a higher or faster expansion rate than glass

Explanation:

This is because When a container expands, the reservoir in the glass expands at the same rate as the glass. Thus, if there is something in a glass and both expand at the same rate, they have no change - but if the contents expand faster, they will fill the container to a higher level, and if the contents expand slower, they will fill the container to a lower level (relative to the new size of the container).

Answer:

Matter's resistance to a change in motion is called INERTIA and is directly proportional to the mass of an object.

Explanation:

Answer;

A)S(t)=96t-16t² +432

B)it will take 9 seconds for the ball to reach the ground.

C)864feet

Explanation:

We were given an initial height of 432 feet.

And v(t)= 96-32t

A) we are to Find​ s(t), the function giving the height of the ball at time t

The position, or heigth, is the integrative of the velocity. So

S(t)= ∫(96-32)dt

S(t)=96t-16t² +K

S(t)=96t-16t² +432

In which the constant of integration K is the initial height, so K= 432

b) we need to know how long will the ball take to reach the​ ground

This is t when S(t)= 0

S(t)=96t-16t² +432

-16t² +96t +432=0

This is quadratic equation, if you solve using factorization method we have

t= -3 or t= 9

Therefore, , t is the instant of time and it must be a positive value.

So it will take 9 seconds for the ball to reach the ground.

C)V=s/t

Velocity= distance/ time

=96=s/9sec

S=96×9

=864feet

By applying the integrations,

(a) [tex]S = 96t-16t^2+432[/tex]

(b) Time will be "t = 9".

(c) Height will be "576"

Given:

Height,

Initial velocity,

According to the question,

(a)

Integrate v:

Initial Condition,

→ [tex]S = 96t-16t^2+432[/tex]

(b)

Hits the ground when,

→ [tex]0=96t-16t^2+432[/tex]

→ [tex]t =9[/tex]

(c)

Maximum height when,

→ [tex]0 = 96-32 t[/tex]

→ [tex]t = 3[/tex]

Now,

→ [tex]S = 96\times 3-16\times 3^2+432[/tex]

      [tex]= 576[/tex]

Thus the answer above is correct.

Learn more:

https://brainly.com/question/16105731

Complete Question

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .

Part A. Calculate  the coil's self-inductance.

Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.

Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf from a to b or from b to a?

Answer:

Part A  

       [tex]L = 0.000863 \ H[/tex]

Part B  

       [tex]\epsilon = 0.863 \ V[/tex]

Part C

    From terminal a to terminal b

Explanation:

From the question we are told that

      The  number of turns is  [tex]N = 590 \ turns[/tex]

      The cross-sectional area is  [tex]A = 6.20 cm^2 = 6.20 *10^{-4} \ m[/tex]

      The  radius is [tex]r = 5.0 \ cm = 0.05 \ m[/tex]

Generally the coils self -inductance is mathematically represented as

              [tex]L = \frac{ \mu_o N^2 A }{2 \pi * r }[/tex]

Where [tex]\mu_o[/tex] is the permeability of  free space with value [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]

substituting values

             [tex]L = \frac{ 4\pi * 10^{-7} * 590^2 6.20 *10^{-4} }{2 \pi * 0.05 }[/tex]

             [tex]L = \frac{ 2 * 10^{-7} * 590^2 6.20 *10^{-4} }{ 0.05 }[/tex]

             [tex]L = 0.000863 \ H[/tex]

Considering the Part B

      Initial current is [tex]I_1 = 5.00 \ A[/tex]

      Current at time t is [tex]I_t = 3.0 \ A[/tex]

       The  time taken is  [tex]\Delta t = 3.00 ms = 0.003 \ s[/tex]

The self-induced emf is mathematically evaluated as

          [tex]\epsilon = L * \frac{\Delta I}{ \Delta t }[/tex]          

=>         [tex]\epsilon = L * \frac{ I_1 - I_t }{ \Delta t }[/tex]

substituting values

             [tex]\epsilon = 0.000863 * \frac{ 5- 2 }{ 0.003 }[/tex]  

             [tex]\epsilon = 0.863 \ V[/tex]

The direction of the induced emf is  from a to b because according to Lenz's law the induced emf moves in the same direction as the current

This question involves the concepts of the self-inductance, induced emf, and Lenz's Law

A. The coil's self-inductance is "0.863 mH".

B. The self-induced emf in the coil is "0.58 volts".

C. The direction of the induced emf is "from b to a".

A.

The self-inductance of the coil is given by the following formula:

[tex]L=\frac{\mu_oN^2A}{2\pi r}[/tex]

where,

L = self-inductance = ?

[tex]\mu_o[/tex] = permeability of free space = 4π x 10⁻⁷ N/A²

N = No. of turns = 590

A = Cross-sectional area = 6.2 cm² = 6.2 x 10⁻⁴ m²

r = radius = 5 cm = 0.05 m

Therefore,

[tex]L=\frac{(4\pi\ x\ 10^{-7}\ N/A^2)(590)^2(6.2\ x\ 10^{-4}\ m^2)}{2\pi(0.05\ m)}[/tex]

L = 0.863 x 10⁻³ H = 0.863 mH

B.

The self-induced emf is given by the following formula:

[tex]E=L\frac{\Delta I}{\Delta t}\\\\[/tex]

where,

E = self-induced emf = ?

ΔI = change in current = 2 A

Δt = change in time = 3 ms = 0.003 s

Therefore,

[tex]E=(0.000863\ H)\frac{2\ A}{0.003\ s}[/tex]

E = 0.58 volts

C.

According to Lenz's Law, the direction of the induced emf always opposes the change in flux that causes it. Hence, the direction of the induced emf will be from b to a.

Learn more about Lenz's Law here:

https://brainly.com/question/12876458?referrer=searchResults

Answer:

D. A convex lens in air

Explanation:

This is because the air tight plastic under water will reflect light rays in the same manner as a convex lens

Explanation:

According to Ohms Law :

V = I * R

(A) R (Resistance) = 0.022 / 0.75 = 0.03 Ohms

Also,

[tex]r = \alpha \frac{length}{area} = \alpha \frac{5.8}{3.14 \times 0.001 \times 0.001} [/tex]

(B)

[tex] \alpha(resistivity) = 1.62 \times {10}^{ - 8} [/tex]

Drift speed is missing. It is given as;

1.7 × 10^(-5) m/s

A) R = 0.0293 ohms

B) ρ = 1.589 × 10^(-8)

C) n = 8.8 × 10^(28) electrons

This is about finding, resistance and resistivity.

Length; L = 5.8 m

Diameter; d = 2mm = 0.002 m

Radius; r = d/2 = 0.001 m

Voltage; V = 22 mv = 0.022 V

Current; I = 750 mA = 0.75 A

Area; A = πr² = 0.001²π

Drift speed; v_d = 1.7 × 10^(-5) m/s

R = V/I

R = 0.022/0.75

R = 0.0293 ohms

ρ = RA/L

ρ = (0.0293 × 0.001²π)/5.8

ρ = 1.589 × 10^(-8)

J = n•e•v_d

Where;

J = I/A = 0.75/0.001²π A/m² = 238732.44 A/m²

e is charge on an electron = 1.6 × 10^(-19) C

v_d = 1.7 × 10^(-5) m/s

n is number of free electrons per unit volume

Thus;

238732.44 = n(1.6 × 10^(-19) × 1.7 × 10^(-5))

238732.44 = (2.72 × 10^(-24))n

n = 238732.44/(2.72 × 10^(-24))

n = 8.8 × 10^(28)

Read more at; brainly.com/question/17005119

Answer: Speed = [tex]3.10^{-31}[/tex] m/s

Explanation: Like in classical physics, when external net force is zero, relativistic momentum is conserved, i.e.:

[tex]p_{f} = p_{i}[/tex]

Relativistic momentum is calculated as:

p = [tex]\frac{mu}{\sqrt{1-\frac{u^{2}}{c^{2}} } }[/tex]

where:

m is rest mass

u is velocity relative to an observer

c is light speed, which is constant (c=[tex]3.10^{8}[/tex]m/s)

Initial momentum is zero, then:

[tex]p_{f}[/tex] = 0

[tex]p_{1}-p_{2}[/tex] = 0

[tex]p_{1} = p_{2}[/tex]

To find speed of the heavier fragment:

[tex]\frac{mu_{1}}{\sqrt{1-\frac{u^{2}_{1}}{c^{2}} } }=\frac{mu_{2}}{\sqrt{1-\frac{u^{2}_{2}}{c^{2}} } }[/tex]

[tex]\frac{1.86.10^{-27}u_{1}}{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } }=\frac{3.10^{-28}.0.844.3.10^{8}}{\sqrt{1-\frac{(0.844c)^{2}}{c^{2}} } }[/tex]

[tex]\frac{1.86.10^{-27}u_{1}}{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } }=1.42.10^{-19}[/tex]

[tex]1.86.10^{-27}u_{1} = 1.42.10^{-19}.{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } }[/tex]

[tex](1.86.10^{-27}u_{1})^{2} = (1.42.10^{-19}.{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } })^{2}[/tex]

[tex]3.46.10^{-54}.u_{1}^{2} = 2.02.10^{-38}.(1-\frac{u_{1}^{2}}{9.10^{16}} )[/tex]

[tex]3.46.10^{-54}.u_{1}^{2} = 2.02.10^{-38} -[2.02.10^{-38}(\frac{u_{1}^{2}}{9.10^{16}} )][/tex]

[tex]3.46.10^{-54}.u_{1}^{2} = 2.02.10^{-38} -2.24.10^{-23}.u^{2}_{1}[/tex]

[tex]3.46.10^{-54}.u_{1}^{2}+2.24.10^{-23}.u^{2}_{1} = 2.02.10^{-38}[/tex]

[tex]2.24.10^{-23}.u^{2}_{1} = 2.02.10^{-38}[/tex]

[tex]u^{2}_{1} = \frac{2.02.10^{-38}}{2.24.10^{-23}}[/tex]

[tex]u_{1} = \sqrt{9.02.10^{-62}}[/tex]

[tex]u_{1} = 3.10^{-31}[/tex]

The speed of the heavier fragment is [tex]u_{1} = 3.10^{-31}[/tex]m/s.

Answer:

8.1 m

Explanation:

Convert km/h to m/s.

45 km/h × (1000 m/km) × (1 h / 3600 s) = 12.5 m/s

Distance = speed × time

d = (12.5 m/s) (0.65 s)

d = 8.125 m

Explanation:

(a) Given that,

Area of a parallel plate capacitor, [tex]A=1.8\ cm^2=1.8\times 10^{-4}\ m^2[/tex]

The separation between the plates of a capacitor, [tex]d=0.01\ mm = 10^{-5}\ m[/tex]

The dielectric constant of, k = 2.1

When a dielectric constant is inserted between parallel plate capacitor, the capacitance is given by :

[tex]C=\dfrac{k\epsilon_o A}{d}[/tex]

Putting all the values we get :

[tex]C=\dfrac{2.1\times 8.85\times 10^{-12}\times 1.8\times 10^{-4}}{0.01\times 10^{-3}}\\\\C=3.345\times 10^{-10}\ F\\\\C=334.5\ pF[/tex]

(b) We know that the Teflon has dielectric strength of 60 MV/m, [tex]E=60\times 10^6\ V/m[/tex]

The voltage difference between the plates at this critical voltage is given by :

[tex]V=Ed\\\\V=60\times 10^6\times 0.01\times 10^{-3} \\\\V=600\ V[/tex]

or

V = 0.6 kV

We have that the Capacitance and potential difference is mathematically given as



Question Parameters:

having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm

having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.

a)

Generally the equation for the Capacitance  is mathematically given as

[tex]C=\frac{ke_0A}{d}\\\\Therefore\\\\C=\frac{2.1*1.80e-4*8.85e12}{0.01e-3}\\\\[/tex]

C=334.68pF

b)

Generally the equation for the Capacitance  is mathematically given as

[tex]Vmax=\frac{Q}{C}[/tex]

Where

Q is the charge on the plates, and hence not given

Therefore, maximum potential difference is

[tex]Vmax=\frac{Q}{334.68pF}[/tex]

For more information on potential difference visit

https://brainly.com/question/14883923