6.68x [tex]10^{-7}[/tex] [tex]m^{2}[/tex] is the minimum cross-sectional area required of a vertical steel cable from which is suspended a 280- kg chandelier mass, m, is equal to 280 kg; safety factor, 8.
Steel's tensile strength is P and its stress is force (f)/Area ( A)
A = F /P
A is equal to mg /8x tensile A.
280 x 9 . 8/ 8 X 500 X106 \s
A = 6.68x [tex]10^{-7}[/tex] [tex]m^{2}[/tex]
What is Tensile Strenth?
Stress, which is quantified as force per area, is the definition of tensile strength. Usually, it is expressed in terms of Pa or psi. Tensile modulus is an intense attribute, which means that the size of a test specimen has no bearing on its value. However, it also depends on other elements like the specimen's preparation, temperature, and the existence of surface flaws.
to know more about mass, visit to:-
https://brainly.com/question/19694949
#SPJ4
a car is traveling at 30 km per hour. a bug hits the windscreen and goes splat. which object experiences the greater force?
When a car is traveling at speed of 30 km per hour. a bug hits the windscreen and goes splat the bug's force on the windshield is equal to the windshield's force on the bug.
Why bug's force on the windshield is equal to the windshield's force on the bug?Bug's force on the windshield is equal to the windshield's force on the bug because the system bug-car maintains its overall momentum during the collision, the change in the car's momentum is equal to and opposes the change in the bug's momentum.
To know more about force visit
https://brainly.com/question/13191643
#SPJ4
An obiect drops from a cliff. If
The final velocity of the object after 5 seconds it was dropped is determined as 50 m/s.
What is the final velocity of the object after 5 seconds?The final velocity of the object after 5 seconds it was dropped is calculated by applying the following kinematic equation as shown below.
v = u + at
where;
u is the initial velocity of the objecta is the acceleration of the objectt is the time of motion of the objectDuring the vertical motion of an object, the vertical velocity of the object decreases as the object moves upwards and eventually becomes zero as the object reaches maximum height.
The vertical velocity of the object starts to increase again when the object start falling downwards and becomes maximum before the object hits the ground.
v = 0 + ( 10 m/s² ) ( 5 s )
v = 50 m/s
Learn more about final velocity here: https://brainly.com/question/25905661
#SPJ1
The complete question is below:
if the object falls from the cliff falls with a constant acceleration of 10 m/s2. Find its speed after 5 seconds it was dropped.
171) a force of 16.88 n is applied tangentially to a wheel of radius 0.340 m and gives rise to an angular 171) acceleration of 1.20 rad/s2. calculate the rotational inertia of the wheel.
The rotational inertia of the wheel which has a radius of 0.34 m is 4.782 kgm²
The force applied tangentially to the wheel = 16.88 N
The radius of the wheel = 0.340 m
The angular acceleration of the well = 1.20 rad /s²
The rotational inertia can be found using the formula,
I = F x r / α
where I is the rotational inertia
F is the force applied
r is the radius of the wheel
α is the angular acceleration
Let us substitute the known values in the above equation, we get
I = 16.88 x 0.34 / 1.20
= 5.7392 / 1.20
= 4.782 kgm²
Therefore, the rotational inertia is 4.782 kgm²
Learn more about the rotational inertia in
https://brainly.com/question/22513079
#SPJ4
newton's second law in 1 dimension: what magnitude net force is required to accelerate a 1200-kg car uniformly from 0 m/s to 27.0 m/s in 10.0 s?
The required force is F = 3240 N.
As a result,
1200 kg is the car's mass.
Initial speed of the vehicle, u = 0.
The car's final speed is 27 meters per second.
Thus we have to first calculate the acceleration and then substitutes its value in the force formula
Taking time, t = 10 s
F = m a, where a represents the vehicle's acceleration, is the formula for the required force.
a= v - u / t
thus a = 27 - 0/ 10
a = 27/ 10
F = 1200 X 27 / 10
F = 3240 N.
Therefore, this is the necessary solution.
To know more about force you may visit the link:
https://brainly.com/question/28875770
#SPJ4
What is the ke of an object that has a mass of 2kg and a velocity of 8m/s
The kinetic energy of the object is 64 joule.
What is kinetic energy?According to the definition of kinetic energy in physics, it is the amount of work that an item may accomplish while in motion.
As a scalar quantity, kinetic energy can only be fully defined by its magnitude. SI unit of kinetic energy is Joule.
Given that: mass of the object: m = 2 kg.
Velocity of the object: v = 8 m/s.
Hence, kinetic energy of it =1/2* mass* velocity^2
= 1/2*mv^2
= 1/2 × 2 × 8^2 joule
= 64 joule.
Hence the kinetic energy is 64 joule.
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ1
Hooke's law states that the restoring force of a spring is directly proportional to a small displacement. Students in physics class were conducting an experiment to determine the difference in displacement among various springs. They wanted to determine if displacement not only varied with mass but also with the type of spring used. The class tested twenty springs; they varied in length, circumference, and material. They used an assortment of masses as well. On some springs they used masses of 5g increments; on others, masses of 10g increments. After hanging the masses from each spring, they measured how far the springs stretched. The students concluded that thin, aluminum springs had greater displacement than short, thick, iron springs. How could the students improve the validity of the data in this experiment to better support their conclusion?.
The kind of spring should be held constant so as to improve the validity of the experiment.
What is Hooke's law?Hooke's law states that the force that acts on a spring is directly proportional to the extension of the spring as long as the elastic limit is not exceeded.
As such, we can now understand that we can only be able to talk about the Hooke's law if there is no way in which the material has passed the elastic limit of the material. In this case, we are told that the students just embarked on a kind of experiment and they want to be able to verify the validity of the Hooke's law.
We saw that the masses that were hanged were increased but the springs were also changed. This would not allow us to determine the force constant and the Hooke's law accurately.
Learn more about Hooke's law:https://brainly.com/question/29126957
#SPJ1
an airline employee tosses two suitcases in rapid succession, with a horizontal velocity of 7.2 ft/s, onto a 50-lb baggage carrier which is initially at rest. (a) knowing that the final velocity of the baggage carrier is 3.6 ft/s and that the first suitcase the employee tosses onto the carrier has a weight of 30 lb, determine the weight of the other suitcase. (b) what would be the final velocity of the carrier if the employee reverses the order in which he tosses the suitcases?
The weight of the second suitcase is approximately 54.7 lbs. To find the weight of the second suitcase, you can use the principle of conservation of momentum.
How to find weight of the suitcase ?The momentum of the first suitcase is given by its mass (30 lbs) multiplied by its velocity (7.2 ft/s):
P1 = m1 * v1
= 30 lbs * 7.2 ft/s
= 216 lbs*ft/s
The momentum of the second suitcase is given by its mass (m2) multiplied by its velocity (7.2 ft/s):
P2 = m2 * v2
= m2 * 7.2 ft/s
The momentum of the baggage carrier is given by its mass (50 lbs) multiplied by its velocity (3.6 ft/s):
P3 = m3 * v3
= 50 lbs * 3.6 ft/s
= 180 lbs*ft/s
The total momentum of the system after the suitcases are tossed onto the carrier is the sum of the momenta of the three objects:
Ptotal = P1 + P2 + P3
= 216 lbsft/s + m2 * 7.2 ft/s + 180 lbsft/s
Since the total momentum of the system before and after the suitcases are tossed onto the carrier must be the same, you can set the total momentum before the suitcases are tossed onto the carrier equal to the total momentum after the suitcases are tossed onto the carrier:
0 = 216 lbsft/s + m2 * 7.2 ft/s + 180 lbsft/s
Solving for m2, the mass of the second suitcase, you get:
m2 = (216 lbsft/s + 180 lbsft/s) / (7.2 ft/s)
= 396 lbs*ft/s / 7.2 ft/s
= 54.7 lbs
Therefore, the weight of the second suitcase is approximately 54.7 lbs.
To learn more about momentum refer :
https://brainly.com/question/1042017
#SPJ4
an airplane flies horizontally at a speed of 351 km/h and drops a crate that falls to the horizontal ground below. neglect air resistance.part (a) if the altitude of the plane was 580 m, then how far, horizontally in meters, did the crate move as it fell to the ground?
Refer to the attached photos. I would appreciate a rate :)
two identical waves are emitted from two sources. if destructive interference occurs at a point where the path length difference is 1 meter, what is a possible wavelength?
The essential prerequisite for destructive interference is a half-wavelength shift between the two waves.
Whenever two identical waves are superimposed in phase, constructive interference happens. When two identical waves are overlaid perfectly out of phase, destructive interference results.
What occurs when two waves interact destructively?Interference that is detrimental is what this is. The crest of one wave will exactly meet up with the trough of the second wave, and they will cancel each other out if the two waves (with the same amplitude) are moved by exactly half a wavelength when they combine.
Two waves must have the same amplitude traveling in opposing directions in order to interact destructively.
learn more about Interference refer
https://brainly.com/question/2166481
#SPJ4
a particular tuning fork generates sound waves at a frequency of 440-hz. if you are 10 meters away from the tuning fork, how many wavelengths are contained between you and the fork?
Number of wavelengths are less than 1 which contained between me and the tuning fork which generated a frequency of 440Hz.
The tuning fork has a design that joins the closures of two sticks. While the tuning fork is vibrated, the tuning fork more than once approaches and afterward creates some distance from one another. The vibration component is straightforward, so it creates a sound with a solitary recurrence well. It has been utilized since old to make hints of explicit frequencies.
We know that wavelength is given by the formula=speed/frequency,or
λ=c/v
Now,we have frequency(v)=440Hz,also we know that speed of sound in air is 340m/sec
=>λ=340/440
=>λ=0.772m
Here, we can see that λ=0.772m which shows that less than one wavelength are contained between me and fork.
Hence,count of wavelength is less than one.
To know more about tuning fork, visit here:
https://brainly.com/question/13032605
#SPJ4
in the photoelectric experiments the current (number of electrons emitted per unit time) is proportional to the intensity of light. can this result alone be used to distinguish between the classical and quantum theories
As we already know that intensity of light used is proportional to the no of electrons emitted per unit of time from the metal plate in the photoelectric effect and does not affect the energy of the emitted electrons and so the stopping potential of the photoelectric cell.
so, if we treat light as a packet of energy and follow quantum theory then it can only emit the electrons as energy is provided as a whole and there is no gap between the striking of photons and the emission of electrons from the metal plate but if we follow the classical theory of light being a wave than the intensity does not matter and no electron can be emitted as energy is provided in continuous form as energy can't be stored and used together.
know more about 'Photoelectric effect' here :
brainly.com/question/26465043
A car accelerates at a rate of 2.0 m/s2. If its original speed is 8.0 m/s, how many seconds will it take the car to reach a final speed of 28.0 m/s?(Prefered is using KWEPA method)
The answer is, time = 10 secs
Given:
Initial Velocity = = 8.0 m/s
Final Speed = = 28.0 m/s
Acceleration = a = ?
Required:
Time = t = ?
Formula:
2 = (28-8)/t
2 = 20/t
t = 20/2
t = 10 seconds
Learn more about acceleration here: https://brainly.com/question/460763
Which of these does a balanced chemical
equation show?
the speed of a reaction
elements created by a reaction
phase changes taking place during a
reaction
the number of atoms involved in a reaction
A balanced chemical reaction shows the element created by the reaction, phase changes during the reaction, and the number of atom involved in it.
What are balanced chemical equation?
A balanced chemical equation is a chemical equation in which the number of atoms for each element in the reaction are equal on both sides of the equation. This is important in chemistry because it ensures that mass is conserved in a chemical reaction. For example, the combustion of methane (CH4) can be represented by the following balanced chemical equation:
CH4 + 2O2 → CO2 + 2H2O
In this equation, there are 4 atoms of carbon (C) on the left side and 4 atoms of carbon on the right side, indicating that all of the carbon has been accounted for in the reaction. There are also 8 atoms of oxygen (O) on the left side and 8 atoms of oxygen on the right side, 4 atoms of hydrogen (H) on the left side and 4 atoms of hydrogen on the right side, and 4 atoms of oxygen (O) on the left side and 4 atoms of oxygen on the right side, indicating that all of the elements have been accounted for in the reaction.
To learn more about balanced chemical equations
https://brainly.com/question/26694427
#SPJ1
A 5.3 kg bowling ball begins rolling down a lane at the bowling alley at 6.6 m/s. When it strikes the pins, it is estimated to be moving at 4.0 m/s. What is the magnitude of energy that is lost due to friction?
The magnitude of energy that is lost due to friction is 73.7Joules.
What is energy ?In order to accomplish work and to produce heat and light, energy must be transferred to a body or to a physical system. Energy is the quantitative attribute that does this. Energy is a preserved resource; according to the rule of conservation of energy, energy can only be transformed from one form to another and cannot be created or destroyed.
Computers, vehicles, communications, state-of-the-art medical technology, and many other things are all powered by energy. The demand for dependable and economical energy is especially pressing for emerging countries. It can be beneficial and even life-saving.
Energy required by the body is the kinetic energy
Kinetic Energy = 1 / 2 mv²
m = mass
v = velocity
For the 5.3kg moving at 6.6m/s
kE = 1/2 * 5.3 * 6.6²
KE = 1/2 * 5.3 * 43.56
KE = 115.71Joules
for the 5.3kg moving at 4m/s
KE = 42 joules
Amount of energy lost
= 115.71Joules - 42 joules
= 73.7 joule
Thus, the amount of Energy lost is73.7Joules.
To learn more about energy, follow the link;
https://brainly.com/question/1932868
#SPJ1
how many molecules of water are in a collection of snowflakes with a mass of 5.00 mg?
A normal snowflake may contain 1,000,000,000,000,000,000, or one quintillion, water molecules.
How many molecules of water are in a snowflake?The variety of sizes and shapes of snowflakes is endless. A lot of them seem to be two-dimensional works of art. Others resemble a tangled collection of ice strands that are beginning to fall apart. While some may fall as multi-flake clusters, most arrive as single particles. The source of all of them is the same: clouds, which typically float at a height of at least one kilometer (0.6 miles).The air up there can get very chilly throughout the winter and will become more colder as you ascend. Those clouds must be below freezing for snowflakes to form. albeit not freezing. A cloud's moisture causes snowflakes to develop. A cloud cannot store enough water for anything to precipitate out if the air temperature is sufficiently low. A balance is therefore required. For this reason, the majority of flakes form at or just below freezing, or 0o Celsius (32o Fahrenheit). Cooler climates can produce snow, but the less moisture there is to form snowflakes the colder it gets.In reality, for a flake to develop, the air inside a cloud must be super-moisture-dense. Because of this, there is more water in the air than is ordinarily feasible. When a substance is supersaturated, the relative humidity might exceed 101 percent. This indicates that 1% more water than the air should be able to carry is present.A cloud will attempt to expel extra water vapor from the air if there is an excessive amount present. Some of that surplus has the potential to crystallize and flash freeze, after which it will slowly drift to the earth.To Learn more About snowflake refer to:
https://brainly.com/question/27563698
#SPJ1
Which choice below explains what is happening in a liquid as it turns into a gas?
a. The particles speed up and spread apart
b. The particles speed up and come closer together
c. The particles slow down and spread apart
d. The particles slow down and come closer together
a. The particles speed up and spread apart, in a liquid as it turns into a gas.
How do particles flow in gases and liquids?Particles in liquids are dispersed randomly across the container and are relatively near to one another. Due to the closer proximity of the particles, collisions between them happen more frequently than in gases even if particles are moving quickly in all directions.
What two characteristics separate liquid from gas?A liquid has a fixed shape and volume as opposed to a gas, which is how they differ from one another. While a liquid keeps a consistent volume, a gas adopts the shape of its container. Additionally, gas is more compressible than liquid. This implies that a gas can be compressed into a smaller area than a liquid.
Learn more about particles in liquid here:
brainly.com/question/11036539
#SPJ1
a watermelon explodes into three equal masses. one mass moves east at 15.0 m/s. if a second mass moves at a velocity of 10.0 m/s 45.0o s of e, what is the velocity of the third mass? (hint: the total momentum is zero, so how will your vector arrows add up?)
The velocity of third mass of watermelon is 3.12m/sec if it explodes into three equal masses.
We know that we need to conserve the momentum of watermelon in a certain direction.Also,we know that initial momentum of watermelon is zero,it means that according to law of conservation of momentum final momentum should be zero.
Now,initial momentum of watermelon=0Kg-m/sec
Alos,we know that momentum =mass× velocity
Now,suppose watermelon has mass m.When it explodes into three equal parts,then the mass of each watermelon pieces is m/3
=>So,final momentum of piece moving to east=(m/3)×15
Similarly final momentum of second and third piece are
(m/3)×10×1/√2 and (m/3) × v × (1/√2)
So,conserving momentum,we get
=>0=(m/3) × 15 +((m/3)×10×1/√2 ) + (m/3)×10×1/√2 )×v
=> - (15 + 10/√2) = (10/√2)×v
=> - (15√2 + 10) = 10v
=>v = (15√2 + 10)/10
=>v= -(21.21+10)/10
=>v= -31.21/10
=>v= -3.12m/sec
Here negative sign shows that mass will move opposite direction to first piece.
Hence, required velocity is 3.12m/sec.
To know more about velocity, visit here:
https://brainly.com/question/18084516
#SPJ4
to meet a u.s. postal service requirement, footwear must have a coefficient of static friction of 0.525 or more on a specified tile surface. a typical athletic shoe has a coefficient of 0.785. in an emergency, what is the minimum time interval in which a person starting from rest can move 2.85 m on a tile surface if she is wearing the following footwear?
A minimal time period is required to accelerate through x=3.00m because maximal static friction produces the force that creates maximum acceleration.
Explain what an acceleration is.acceleration is the rate of change in both direction and speed of velocity over time. When anything moves faster or slower in a straight line, it is said to have been accelerated. Because of direction is always shifting, motion on a circle accelerates even while the speed is constant.
A person moves by the help of frictional force, as a result of gtound reaction. So, the formula for frictional force is:
F = μR
where,
F = frictional force
μ = coefficient of friction
R = Normal Reaction = Weight of Body = W = mg
Therefore,
F = μmg
but, from Newton's 2nd Law of Motion:
F = ma
Comparing both equations, we get:
μmg = ma
a = μg ---------- equation (1)
Now, to calculate the distance moved by a body, we use 2nd equation of motion:
s = (Vi)(t) + (0.5)at²
using equation (1), we get:
s = (Vi)(t) + (0.5)μgt²
where,
s = distance moved by body
Vi = initial velocity of body
t = time taken to cover the distance
g = acceleration due to gravity
(a)
Vi = 0 m/s
g = 9.8 m/s²
s = 3.2 m
μ = 0.5
t = ?
Therefore,
3.2 m = (0 m/s)(t) + (0.5)(0.5)(9.8 m/s²)t²
t² = 3.2 m/(0.5)(0.5)(9.8 m/s²)
t = √1.30612 s²
t = 1.14 s
(a)
Vi = 0 m/s
g = 9.8 m/s²
s = 3.2 m
μ = 0.5
t = ?
Therefore,
3.2 m = (0 m/s)(t) + (0.5)(0.5)(9.8 m/s²)t²
t² = 3.2 m/(0.5)(0.5)(9.8 m/s²)
t = √1.30612 s²
t = 1.14 s
(a)
Vi = 0 m/s
g = 9.8 m/s²
s = 3.2 m
μ = 0.87
t = ?
Therefore,
3.2 m = (0 m/s)(t) + (0.5)(0.87)(9.8 m/s²)t²
t² = 3.2 m/(0.5)(0.87)(9.8 m/s²)
t = √0.75 s²
t = 0.87 s
What are acceleration and speed exactly?The rate of change in displacement is known as velocity. Acceleration is the rate at which speed changes. The fact that velocity contains both magnitude and orientation makes it a vector quantity. Acceleration is also a vector quantity since it is simply the rate during which velocity varies.
To know more about acceleration visit:
https://brainly.com/question/12550364
#SPJ4
light travels along the length of a 1500-nm-long nanostructure. when a peak of the wave is at one end of the nanostructure, is there a peak or a valley at the other end if the wavelength is (a) 500 nm and (b) 1000 nm?
If the light travels along the length of a 1500 nm , then
(a) if the wavelength is 500 nm then there will be a peak at other end .
(b) if the wavelength is 1000 nm then there will be a valley .
Wavelength is defined as the distance between two consecutive peaks or valleys .
given the length is = 1500 nm ;
we know that , the formula is L = nλ ;
Part (a) ;
for peak at other end ,
n should be a whole number ;
So , λ = 500 nm
n = 1500/500 = 3 ,
Part(b)
λ = 1000 nm ;
n = 1500/1000
= 1.5
Therefore , (a) There will be a peak at other end .
(b) There will not be a peak at other end .
Learn more about Wavelength here
https://brainly.com/question/19542918
#SPJ4
a current of 11 amps at 240 volts flows through an electric range. if it is user an average of 1 hour/day Calculate the kwhr used per week.
The kWh used per week by the electric range whose voltage and current is 240 V and 11 A respectively is 18.48 kWh.
What is electric kilowatt-hour (kWh)?
A kilowatt-hour is a unit of energy: one kilowatt of power for one hour. In terms of SI derived units with special names, it equals 3.6 megajoules (MJ).
To calculate the kWh per week of the electric range, we use the formula below.
Formula:
E = VIt/1000...............Equation 1Where:
E = Electric energy in kWh per week V = VoltageI = Currentt = Total timeFrom the question,
Given:
V = 240 VI = 11 ampst = 1 hour per day = 1×7 = 7 hours per weekSubstitute these values into equation 1
E = 240×11×7/1000E = 18.48 kWhHence, the kWh used per week is 18.48 kWh.
Learn more about electric kilowatt-hour (kWh) here: https://brainly.com/question/13494371
#SPJ1
197) a submarine in neutral buoyancy is 100 m below the surface of the water. what air pressure must 197) be supplied to remove water from the ballast tanks in order for the submarine to surface?
Air pressure must be supplied to remove water from the ballast tanks is 9.8*105 N/m^2.
Buoyancy is the upward force exerted by a liquid that opposes the weight of a partially or fully submerged object. In a liquid column, the pressure increases with depth due to the weight of the liquid above. Therefore, the pressure at the bottom of the liquid column is higher than the pressure at the top of the column. Similarly, the pressure at the bottom of an object immersed in liquid will be greater than at the top of the object. A pressure differential results in a net upward force on an object. The magnitude of the force is proportional to the pressure difference and corresponds to the weight of the liquid (as explained by Archimedes' principle). This is the displaced liquid that would otherwise occupy the underwater volume of the object.
We know that pressure below the surface of water is P1 = Po +hdg
pressure at the surface of water is P2 = Po
Then pressure difference is P = P1 -P2 = hdg
h = depth = 100 m
d = density of water = 1000 kg/m3
g = 9.8 m/s2
Then P = 100*1000*9.8 = 9.8*105 N/m^2
Learn more about Buoyancy here:
https://brainly.com/question/451053
#SPJ4
A monkey escaped at the zoo he was able to go 360 meters before the zookeeper caught him. If the monkey was traveling at rate of 18 mls how long was it between when he escaped and zookeeper caught him?
what is the equation describing the motion of a mass on the end of a spring which is stretched 8.8 cm from equilibrium and then released from rest, and whose period is 0.66 s ? assume that the displacement at the start of the motion is positive.
The equation for the motion of a mass on the end of a spring with a period of 0.66 seconds and a stretch of 8.8 cm from equilibrium is
y = (8.8cm)cos(3πt).
What is the mathematical formula for the mass's motion?Newton's second law, which states that the force acting on a body is equal to that force multiplied by the acceleration of the center of mass of that body, or F = ma, is the basic equation of motion in classical mechanics.
As we are aware, the SHM equation is as follows:
y = Acos(ωt)
Here, we are aware of
ω = 2π/T
Here it is
T = 0.66s
now that we
ω = 2π/0.66
ω = 3π
We now have
y = (8.8cm)cos(3πt).
To know more about mass visit:
https://brainly.com/question/14017869
#SPJ4
at what temperature, in kelvins, will atoms of a monatomic gas have an average kinetic energy equal to this needed electrical potential energy?
300 kelvin temperature, in kelvins, will atoms of a monatomic gas have an average kinetic energy equal to this needed electrical potential energy.
How do you define potential energy?Potential energy is a form of stored energy that is dependent on the relationship between different system components. When a spring is squeezed or extended, its potential energy increases. If a steel ball is lifted above the ground as opposed to falling to the ground, it has higher potential energy.
Our knowledge of the cosmos and how we fit into it depends on potential energy. In fact, potential energy and the labor necessary to move an item are determined by the position of the object in the universe. Everything we do has an impact on something's potential energy.
Briefing:KE=3/2KT
=6.21*10(-21)
=3/2*1.30*10(-23)*T
T=300 kelvin
To know more about Potential energy visit:
https://brainly.com/question/24284560
#SPJ4
Suppose a 15 N force is applied to the side of a 5.0 kg block that is sitting on a table. The block experiences a frictional force against the force that is applied.
a) What is the weight of the block (FG)?
b) What is the normal force on the block (FN)?
c) If the coefficient of kinetic friction is μk = .10, what is the frictional force on the block (Ff)?
d) What is the net force on the block?
e) What is the acceleration of the block from the net force?
Answer:
Explanation:
Fg = W = mg = (5.0 kg)(9.8 m/s²) = 49 N
Fnormal = W = 49 N
Ff = μFn = (0.10)(49 N) = 4.9 N
Fnet = 15 N - 4.9 N = 10.1 N
a = Fnet/m = (10.1N)/(5.0kg) = 2.02 m/s²
Which one of the following statements concerning electromagnetic waves is false?a. One form of electromagnetic radiation is visible light.b. All electromagnetic waves travel through a vacuum region at the speed of light.c. All electromagnetic waves are transverse waves.d. All electromagnetic waves have the same frequency.e. Electromagnetic waves can travel through solids, liquids, gases, and vacuumregions
Answer:
.Answer: d. All electromagnetic waves have the same frequency.
If you are holding a bucket steady by a rope with a tension force of 20 N, how much does the bucket weigh?
The weight of the bucket suspended by rope held in your hand is 20 N.
What is Newton's third law of motion?
Newton's third law of motion states that for every action there is an equal and opposite reaction. That is the force applied or exerted on an object is equal to the reaction of the object.
Mathematically, the formula for the Newton's third law of motion is given as;
Fa = Fb
where;
Fa is the applied force on the objectFb is the reaction experienced by the objectThe applied force and the reaction force are equal in magnitude but opposite in direction.
Thus, if the tension holding a bucket upward is 20 N, then there must be an equal and opposite force pushing the bucket downwards. The downward force of the bucket or the weight of the bucket must be equal to the tension holding the bucket upwards.
Learn more about weight here: https://brainly.com/question/2337612
#SPJ1
what is the isolation and initial evacuation distance for this material since it is on fire?
Answer:
Isolate spill or leak area for at least 100 meters (330 feet) in all directions. See Table 1 - . If tank, rail car or tank truck is involved in a fire, ISOLATE for 1600 meters (1 mile) in all directions; also, consider initial evacuation for 1600 meters (1 mile) in all directions.
a vertical spring has a spring constant of 100 n/m. when an object is attached to the bottom of the spring, the spring changes from its unstretched length of 0.50 to a length of 0.65 m. the magnitude of the weight of the object is
Answer: Hookes law states F=kX where F is the force applied, k is the spring constant, and X is the extension of the spring from its resting point.Substituting the values in, we get:F=100*(0.65-0.5)=100*0.15=15N
the moment of inertia of an object of mass m(a)m(a) is an intrinsic property of the object, (b) depends on the choice of axis of rotation, (c)(c) is proportional to mm regardless of the choice of axis, (d)(d) both (b)(b) and (c)(c) are correct.
Option (B)is correct
depends on the choice of axis of rotation
What does m in a moment of inertia mean?
Formula for Moment of Inertia
Moment of inertia is defined in general form as I = m r2,
where m is the sum of the product of the mass.
r is the separation from the rotational axis.
What elements affect inertia?
The position and orientation of the rotational axis affect a body's moment of inertia. It also depends on the body's size, shape, and how its mass is distributed around a particular axis. Q.
Learn more about Inertia
Visit
https://brainly.com/question/1358512
#SPJ4
