true/false. documentation is a reference guide that describes the features of the program, designed for the user.

Answer:

The plate thickness required at the base of the tank is approximately 6.6 mm.

Explanation:

To estimate the plate thickness required at the base of the tank, we need to determine the maximum pressure that the tank will experience at the base. The pressure can be calculated using the formula:

P = ρgh

where P is pressure, ρ is the density of the liquid, g is the acceleration due to gravity, and h is the height of the liquid above the base of the tank.

Assuming a density of 1.5 g/cm³ for concentrated nitric acid, the pressure at the base of the tank can be calculated as:

P = 1.5 x 9.81 x 16 = 235.44 kPa

To determine the plate thickness required, we can use the formula for the hoop stress in a cylindrical vessel:

σ = PD/2t

where σ is the stress, P is the pressure, D is the diameter of the vessel, and t is the thickness of the vessel wall.

Rearranging the formula to solve for t, we get:

t = PD/2σ

Assuming a diameter of 6 m and a design stress of 90 N/mm², the plate thickness required at the base of the tank can be calculated as:

t = (235.44 x 6 x 1000) / (2 x 90 x π) ≈ 6.6 mm

Therefore, the plate thickness required at the base of the tank is approximately 6.6 mm.

Answer:

To determine the plate thickness required at the base of the tank, we can use the following formula:

t = (PD)/(2SE - 0.2P)

where:

t = plate thickness

P = design pressure

D = inside diameter of the tank

S = allowable design stress for aluminum

E = joint efficiency factor

Since the tank will contain concentrated nitric acid, which is a hazardous material, it is subject to specific design and safety regulations that require a detailed engineering analysis. Therefore, we will assume a design pressure of 2.5 psi for this calculation, which is a typical value for atmospheric storage tanks.

The joint efficiency factor for welded aluminum is typically 0.70 to 0.85, depending on the welding procedure and inspection method used. For this calculation, we will assume a joint efficiency factor of 0.80.

Plugging in the given values, we get:

t = (2.56)/(2900.80 - 0.22.5)

t = 0.0682 m

Therefore, the plate thickness required at the base of the tank is approximately 0.0682 m, or 68.2 mm

For procedures, arguments are substituted exactly as entered, without checking for memory, registers, or literals.

What are procedures?

Procedures, often known as routines, subroutines, or methods, are a type of subroutine that encapsulates a group of instructions that can be reused. They are often used in programming to break down a big program into smaller, more manageable pieces. In a program, procedures allow the programmer to avoid the repetition of the same code.The parameters in a procedure are substituted exactly as entered, without checking for memory, registers, or literals. Procedures are included in the code as a group of instructions that execute a specific task.

They're like mini-programs inside a bigger one. They can take input from other parts of the program and/or provide results to other parts of the program, but the code inside the procedure is typically self-contained.

Learn more about  arguments and argument passing:https://brainly.com/question/30364739

#SPJ11

The following is used to process and display browser database application forms, reports, and queries: Web Application Server (WAS) is a server that uses web application server technology to deliver web-based applications.

It is a program that manages user requests for web pages and is responsible for generating content that is returned to the user's browser. A Web Application Server is responsible for translating browser requests into database queries that generate the desired output in the form of web pages. A web application server's primary purpose is to deliver web pages that are dynamically generated.

When web users request information from a database via an application, the web application server will interact with the database on the user's behalf. The following are some of the features of web application servers: Database connectivity support is provided. Session management is supported.

Security authentication and authorization for users is provided. Processing of complex business logic is supported. Support for multiple languages is provided. Logging and auditing capabilities are provided in a web application server. A web application server's core responsibility is to provide a runtime environment for web applications. It enables developers to create and deploy applications that can be accessed via the web.

For more such questions on Web Application Server

https://brainly.com/question/26281028

#SPJ11

The given problem is asking for the formulas of x(t) and y(t) that could represent the parametric curve (x(t), y(t)).

What is parametric curve?

Parametric curve is the curve that is defined by equations of the form [tex]x=f(t)[/tex] , [tex]y=g(t)[/tex] where t is the parameter.

So, for a given value of t, x and y coordinates can be found by plugging in that value of t. Different values of t will give different points on the curve.

To find the formulas for x(t) and y(t), the following steps can be used:

Step 1: Identify the shape of the curve. Based on the shape of the curve, we can come up with the equation of the curve.

Step 2: Break the curve into x(t) and y(t) components.

Step 3: Choose a parameter to represent the curve. Typically, we use t as the parameter.

Step 4: Determine the x(t) and y(t) components of the curve based on the chosen parameter.

Step 5: Write the equations of x(t) and y(t).

The equations can be simple linear equations or more complex nonlinear equations.

For example, consider a circular path. The equation of a circle can be represented as [tex](x-a)^2+(y-b)^2=r^2[/tex]

Where a and b represent the coordinates of the center of the circle, and r is the radius of the circle.

To find x(t) and y(t), we can rewrite the equation of the circle as: [tex]x=a+r cos(t)[/tex] and [tex]y=b+r sin(t)[/tex]

where t is the parameter.

So, for different values of t, we can get different points on the circle.

Learn more about Parametric curve here:

https://brainly.com/question/30482587

#SPJ11

When Zara has already pinged the static IP address of the web server and it appears to be online, the next thing she should look at is: Ensure that DNS for the domain is configured correctly.

What is DNS?

DNS (Domain Name System) is a service that converts domain names into IP addresses. The domain name system maps domain names to IP addresses, allowing people to access websites and other online services with familiar, easy-to-remember names instead of IP addresses. DNS maps domain names to IP addresses, enabling web browsers to connect to internet resources. DNS is an important part of the internet's infrastructure, and it is essential for online communication. So, when Zara has already pinged the static IP address of the web server and it appears to be online, the next thing she should look at is ensuring that DNS for the domain is configured correctly.

Hi there, To help troubleshoot the issue Zara is having accessing her company's website through her web browser, she should check that the DNS for the domain is configured correctly. This can be done by pinging the domain name and verifying that the DNS server is responding with the correct IP address. Next, she should ensure that the server's NTP settings are correct, as this will ensure that the server's time is set correctly and that the time-sensitive tasks, such as session authentication, are running properly.

After that, she should verify that the DHCP settings are correct on the server. This will help ensure that the server is assigning the correct IP addresses and the web server will be accessible. Finally, she should check that the LDAP server is also online, as this will ensure that the server can authenticate users who attempt to access the website. I hope this helps!

Zara is having trouble accessing her company's website through her web browser : https://brainly.com/question/17305523  

#SPJ11

The resources should have more capacity at the beginning.

Resources are the things that are available to help us to complete a task. In the context of project management, resources may include people, equipment, materials, money, and time. It is important to manage these resources effectively to ensure that the project is completed on time and within budget.

Capacity refers to the amount of work that a resource is capable of doing. For example, the capacity of a worker might be determined by the number of hours that they can work per day or the amount of work that they can complete within a given period of time. It is important to consider the capacity of resources when planning a project so that you can allocate them effectively.

The resources should have more capacity at the beginning. This is because, at the beginning of a project, there is a lot of work to be done and many resources are needed. As the project progresses, the amount of work decreases, so fewer resources are needed. Therefore, having more capacity at the beginning ensures that there are enough resources to complete the work efficiently and on time.

To learn more about "resource capacity": brainly.com/question/29313227

#SPJ11

Goal Seek is used in Excel to determine the value that a certain cell needs to be changed to in order to reach a specific goal, by altering the value of another cell that is related to the goal cell through a formula or calculation.

When you use Goal Seek, you select a cell that contains a formula and specify the value that you want that formula to return by changing the value in another cell. Excel then uses a trial-and-error approach to determine the value that needs to be entered into the input cell to achieve the desired result.

For example, you might use Goal Seek to determine how much you need to save each month in order to reach a specific savings goal by a certain date. You would set the savings goal as the cell to be changed, and the monthly savings amount as the input cell to be adjusted until the goal is met.

Learn more about Goal Seek https://brainly.com/question/30404127

#SPJ11

The phase of the SDLC where a detailed plan for programmers to follow is generated and a proposed system is documented using flowcharts and data-flow diagrams is the Design phase.

The System Development Life Cycle (SDLC) is a process used by IT professionals to design, create, test, and maintain software. The SDLC process has a significant impact on the productivity of businesses and how software applications are created. During the Design phase, the software’s comprehensive technical requirements are documented. The development team is tasked with developing a plan for how to meet those technical requirements, and the program’s architectural design is created. It is the stage in the software development process where the software's architecture and specifications are established.Flowcharts and data-flow diagrams are used to document the program's architecture and technical requirements.

Learn more about SDLC: https://brainly.com/question/15696694

#SPJ11

An organization must include the following technical standards: operating systems, databases, programming languages, development tools, and servers that are used with each technology stack.

To use a technology stack for software development, an organization needs to include the following technical standards:

Operating System - A technology stack requires a specific operating system, as it is dependent on the underlying system that is used. An organization should choose the operating system that is most suitable for its needs.

Databases - It is important to select a database that supports the specific technology stack. For example, for Java-based technologies, Oracle is a commonly used database.

Programming Languages - Programming languages are an important aspect of a technology stack, and the organization should choose the language that is best suited for its needs.

Development Tools - An organization must choose development tools that support the specific technology stack that is being used. These tools should be easy to use and provide support for debugging and testing.

Servers - A technology stack requires specific servers to run on. An organization must choose the server that is most suitable for its needs, such as Apache Tomcat for Java-based technologies.

In conclusion, to use a technology stack for software development, an organization must include the following technical standards: operating systems, databases, programming languages, development tools, and servers that are used with each technology stack.

To know more about technology stack:https://brainly.com/question/23504399

#SPJ11

Flow conditions refer to the physical properties of a liquid or gas that affect its behavior in a given environment. In river hydraulics, flow conditions are described by the velocity, depth, and gradient of the water in a given reach.

In order to understand the hydraulic behavior of a reach, it is important to identify and describe the flow conditions that exist within it. Existing conditions that may influence hydraulic behavior include the water depth, water velocity, channel width, channel slope, and channel roughness. These factors influence the velocity and turbulence of the water, which in turn affect sediment transport and erosion.

High velocities and turbulence can increase erosion and sediment transport, while low velocities and turbulence can lead to sediment deposition and channel widening. Channel slope also influences the flow conditions, as it affects the velocity and depth of the water as it moves downstream. Steep slopes can lead to high velocities and rapid changes in water depth, while gentle slopes allow for more uniform flow conditions.

Learn more about Flow conditions here:

https://brainly.com/question/17247223

#SPJ11

Energy saved = 21,900 kWh per year

Fuel Saved = 730 liters

Let's dive deeper into the details below.

One can save energy in various ways, such as walking up a floor instead of taking the elevator, walking, or riding a bike for an hour a day instead of driving a car. Here are some ways in which energy can be saved:

1. Turning off lights and electronics when they're not in use

2. Using energy-efficient light bulbs

3. Reducing water usage

4. Using public transportation, biking, or walking instead of driving a car

5. Installing a programmable thermostat

6. Purchasing energy-efficient appliances

7. Using natural light to save energy

8. Properly insulating homes to save energy

9. Upgrading to energy-efficient windows and doors

10. Planting trees and shrubs to shade your home and keep it cool during the summer.

11. Weatherizing your home to keep heat in during the winter.

Assumptions: Let's assume that there are three floors in a building, and each floor has five rooms, and each room has four tube lights (40 watts each) that run for ten hours each day. Now, if we replace these tube lights with LED lights, which consume ten watts each, we can save 30*5*4*40 = 60,000 watts per day.

It will be equal to 60 kWh per day or 21,900 kWh per year.

Assumptions: Let's assume that you drive 20 km every day, and your car's average fuel consumption is 10 km per liter of petrol. If you ride a bicycle instead of driving a car for one hour each day, you can save 20/10 = 2 liters of petrol per day.

It will be equal to 730 liters of petrol per year.

Learn more about energy.

brainly.com/question/1932868

#SPJ11

The volume of the region outside the cone phi = pi /4 and inside the sphere rho = 4 cos phi is 32π/3.

The volume of the region outside the cone phi = pi /4 and inside the sphere rho = 4 cos phi, using spherical coordinates is determined as follows:

Volume is expressed in terms of integrals in Cartesian coordinates by a triple integral. A similar integration is conducted for volume determination in spherical coordinates. Let's determine the limits for ρ, θ, and φ for the given region, as given below:

For φ, the limits range from 0 to π/4
For ρ, the limits range from 0 to 4cos(φ)
For θ, the limits range from 0 to 2π

The volume V of the region R enclosed by the cone and the sphere is given by:

[tex]V = ∭R ρ^2 sin(φ)dρdθdφ[/tex]

Here,[tex]ρ^2 sin(φ)[/tex] represents the element of volume in spherical coordinates. It is equivalent to the Jacobian determinant |J|.

So volume V is given by:

[tex]V = ∫02π ∫0π/4 ∫04cos(φ) ρ^2 sin(φ)dρdφdθ[/tex]

Integrating with respect to ρ, we get

Hence, the volume of the region outside the cone phi = pi /4 and inside the sphere rho = 4 cos phi is 32π/3.

To know more about Volume: https://brainly.com/question/14197390

#SPJ11

The exact volume of the region outside the cone phi = pi /4 and inside the sphere rho = 4 cos phi is (56/3) π.

The formula for finding the volume of the region outside the cone phi = pi /4 and inside the sphere rho = 4 cos phi in spherical coordinates is given by:

V = ∫∫∫ ρ2 sin φ dρ dθ dφ

Here, we have to integrate over the region phi ≤ pi /4 and 0 ≤ θ ≤ 2 pi.

To calculate this, first we need to find the bounds of ρ. The cone phi = pi /4 means that 0 ≤ φ ≤ pi /4. The sphere is given by ρ = 4 cos φ. So the bounds of ρ are 0 ≤ ρ ≤ 4 cos φ.Therefore, the integral becomes:

V = ∫∫∫ ρ2 sin φ dρ dθ dφ

V = ∫0^(2π) ∫0^(π/4) ∫0^(4 cos φ) ρ2 sin φ dρ dφ dθ

V = 32/3 (cos³ φ) |0^(π/4) × θ |0^(2π)= 32/3 [(cos³(π/4)) − (cos³(0))] × (2π)And, cos(π/4) = √2/2, cos(0) = 1.

Thus, the volume is

V = 32/3 [(√2/2)³ − 1³] × (2π)= (64/3 − 8/3) π= (56/3) π.

The exact volume of the region outside the cone phi = pi /4 and inside the sphere rho = 4 cos phi is (56/3) π.

To learn more about "VOLUME OF THE REGION": brainly.com/question/28762310

#SPJ11

The ways of arranging the storage so that you can meet the specifications set by your boss:

The first method for organizing a storage system is RAID. It is one of the most reliable methods for protecting data from hard drive failure. The RAID system uses several hard drives and combines them into a single volume. Data is then written across the drives, thus ensuring that if one fails, there is no data loss.A backup is an excellent method to safeguard data against potential loss due to hardware or software failure. Your storage system should have a routine backup schedule that backs up critical data regularly. The use of cloud storage is increasing in popularity. Cloud storage is a great way to safeguard data against loss due to hardware or software failure.

Learn more about RAID: https://brainly.com/question/28963056

#SPJ11

The first step in the digital signature process where Mike sends a message to Sophie is to create a hash of the message using a secure algorithm.

A digital signature is a method of verifying the authenticity and integrity of digital data or documents. Digital signatures are used to guarantee that the data hasn't been tampered with and to prove who generated it. The digital signature process follows these steps:

The sender hashes the message using a secure algorithm. The sender encrypts the hash using his or her own private key to generate the digital signature. The message and the digital signature are sent to the receiver. The receiver decrypts the digital signature using the sender's public key.

The receiver hashes the received message using the same hash function used by the sender. The receiver compares the two hashes to verify that they are the same. If the hashes match, it confirms that the message has not been tampered with and that the sender is legitimate.

For more such questions on digital signature

https://brainly.com/question/29809712

#SPJ11

At higher engine speeds, and when engine load is high enough, the secondary intake ducts are opened by butterfly valves, reducing restriction and increasing airflow and torque.

What are butterfly valves?
Butterfly valves are a type of valve that consists of a circular disc or plate mounted on a rod or shaft that is positioned in the center of a pipe or duct. The disc can be rotated within the pipe or duct to either partially or completely block the flow of fluid or gas passing through the system.


In an internal combustion engine, the intake system is responsible for supplying the engine with air for combustion. The primary intake ducts are designed to provide air at low to mid-range engine speeds and loads. However, at higher engine speeds and higher loads, the primary intake ducts can become restrictive and limit the amount of air that can enter the engine, reducing performance.

To overcome this limitation, some engines are designed with secondary intake ducts that can provide additional air at higher engine speeds and loads. These secondary ducts are typically smaller in size and are controlled by butterfly valves that can open or close as needed.

When the engine speed and load are low, the butterfly valves remain closed, and the air flows through the primary ducts only. However, as the engine speed and load increase, the butterfly valves open, allowing additional air to flow through the secondary ducts and into the engine. This increases the volume of air available for combustion, which results in increased torque and performance.

Overall, the use of secondary intake ducts with butterfly valves is a way to improve engine performance without sacrificing fuel efficiency or emissions. By providing additional air only when needed, the engine can operate more efficiently and effectively across a wide range of speeds and loads.

To know more about torque visit:
https://brainly.com/question/29024338
#SPJ1

The given statement " Windows Remote Desktop, formerly called Microsoft Terminal Services (mstsc), is the most secure way of remotely connecting to another Windows systems and, as a result, it is used most often by system administrators." is false. While Windows Remote Desktop is a commonly used method of remote connection for system administrators, it is not necessarily the most secure way to remotely connect to another Windows system.

There are other methods, such as Virtual Private Network (VPN) connections and Secure Shell (SSH) connections, that are considered more secure. Additionally, the security of a remote connection can depend on how it is configured and used, so it is important to take appropriate security measures regardless of the remote connection method being used.

You can learn more about Windows Remote Desktop at

https://brainly.com/question/11158930

#SPJ11

An oscilloscope is a type of electronic measurement tool used to visualise and assess electrical changes and waveforms.

An oscilloscope is a flexible electronic measurement tool that can be used in a variety of applications to see and measure electrical signals. It is frequently used in a variety of industries that involve the analysis of electrical circuits and systems, including electronic engineering, telecommunications, medicine, and many more. An oscilloscope shows signals as a voltage against time graph, enabling users to inspect waveforms and quantify crucial elements including amplitude, frequency, and phase. Oscilloscopes are crucial instruments for designing, testing, and troubleshooting electronic systems because they can capture and analyse both analogue and digital signals. They range from small, handheld gadgets to premium tabletop ones with cutting-edge features and capabilities.

Learn more about "oscilloscope" here:

https://brainly.com/question/30809641

#SPJ4

The instrument you are describing is an oscilloscope, also known as an o-scope or scope.

It is a commonly used tool in electronics, telecommunications, and other fields that deal with electrical signals. The oscilloscope allows users to view the shape, frequency, and amplitude of electrical signals over time. It consists of a display screen, an input channel to connect the signal source, and controls to adjust the display settings and perform measurements. The waveform displayed on the screen is a graphical representation of the signal, with the vertical axis representing voltage and the horizontal axis representing time.

Find out more about electronics measurement instruments

brainly.com/question/30330612

#SPJ4

Question:-

Identify the following electronics measurement instrument, which is used to display and measure electrical variations and waveforms. This instrument works by amplifying and displaying electrical signals on a screen, allowing users to measure the amplitude, frequency, and other characteristics of the signal. Some models may also include additional features such as waveform analysis and data logging. What is the name of this instrument?

Horizontal components of reaction at A is 0 N

Vertical components of reaction at A is 3200 N

Reaction at B on the beam is 900 N.m

Lets solve the question in detail.

The horizontal and vertical components of reaction at A, as well as the magnitude of the reaction at B on the beam, can be determined with the given information. Let's start by calculating the reaction at point A:

The horizontal reaction at A = F1cos(90°) = 1200cos(90°) = 0 N
The vertical reaction at A = F1sin(90°) + F2sin(0°) = 1200sin(90°) + 2000sin(0°) = 3200 N

Now, let's calculate the reaction at B:
Reaction at B = F1sin(90°) + F2sin(90°) = 1200sin(90°) + 2000sin(90°) = 3200 N
Magnitude of the reaction at B = √[(1200sin(90°))2 + (2000sin(90°))2] = √[(1200)2 + (2000)2] = 900 N.m

Therefore, the horizontal components of reaction at A is 0 N, the vertical components of reaction at A is 3200 N, and the reaction at B on the beam is 900 N.m.

Learn more about components of reaction.

brainly.com/question/1443888

#SPJ11

If you encounter icing conditions during climb-out after takeoff and with the autopilot engaged, you can expect the autopilot to adjust the aircraft's pitch and power to maintain a constant airspeed, which may not be sufficient to prevent ice buildup on the wings and other critical surfaces.

In such a situation, it is essential to take immediate action to ensure the safety of the flight.

This may include turning off the autopilot and manually adjusting the pitch and power to maintain a safe speed and altitude, activating the aircraft's anti-icing systems, and communicating with air traffic control to request clearance to climb to a higher altitude or change your flight path to avoid the icing conditions.

Learn more about Autopilot at:

https://brainly.com/question/20372893

#SPJ1

Technical drawings employ both an engineering scale and an architect's scale to measure and display items and structures accurately. However, the measurement increments between them vary.

ĵ Numbers on architect scales move incrementally from right to left as well as left to right. The scale those numbers represent is indicated by a whole number or fraction to the left or right of the number line. ĵ Numbers on engineer scales move progressively from left to right.

When designing a structure, architects take the needs and specifications of the client into account. In accordance with the architect's plans, engineers develop the building's plumbing, electrical, and structural systems.

To know more about architect's visit:-

https://brainly.com/question/28425067

#SPJ1

Yes, the job can be performed on the 20 hp lathe given the provided values and using Table 20.2 to obtain the appropriate unit horsepower value.

First, we need to find the actual horsepower available from the lathe, taking into account its efficiency. To do this, multiply the lathe's horsepower by its efficiency: 20 hp * 0.92 = 18.4 hp.

Next, we'll use Table 20.2 to find the appropriate unit horsepower value for alloy steel with a hardness of 325 HB. In this case, the unit horsepower is 5.8 hp/in³/min.

Now, we need to calculate the material removal rate (MRR). MRR is given by the formula: MRR = Cutting Speed * Feed * Depth of Cut. In our case, MRR = 375 ft/min * 0.030 in/rev * 0.150 in = 1.6875 in³/min.

Finally, we need to determine the required horsepower for the operation. To do this, multiply the unit horsepower by the MRR: Required Horsepower = 5.8 hp/in³/min * 1.6875 in³/min = 9.7875 hp.

Since the actually available horsepower from the lathe (18.4 hp) is greater than the required horsepower for the operation (9.7875 hp), the job can be performed on the 20 hp lathe.

Learn more about horsepower at:

https://brainly.com/question/14783214

#SPJ11

It is challenging(difficult) to pass on winding and curving roads.

Winding and curving roads often obstruct the driver's view of what lies ahead. This reduced visibility can make it difficult to anticipate oncoming traffic, pedestrians, or obstacles, increasing the risk of accidents if attempting to pass.

In terms of Uncertain Road Conditions, the nature of winding and curving roads can lead to varying road conditions. These conditions might include sharp turns, uneven surfaces, narrow lanes, and potential hazards around corners. Passing in such conditions can lead to loss of control or collisions.

Read more about winding  here:

https://brainly.com/question/34171500

#SPJ2

The rate of heat transfer by convection is approximately 2.01 kW.

The rate of heat transfer by convection (kW) when the convective heat transfer coefficient is 7.2 W/Km²,

the surface area is 16 m²,

the surface temperature is 317 K, and

the surrounding temperature is 429 K is approximately 2.01 kW.

Let's see how to obtain this result. Basically, we have to find the rate of heat transfer by convection, which is given by this equation:

[tex]q = hA(Ts − T∞)[/tex]

where q is the rate of heat transfer by convection,

h is the convective heat transfer coefficient,

A is the surface area,

Ts is the surface temperature, and

T∞ is the surrounding temperature.

Now, substitute the given values and compute the result:

[tex]q = (7.2 W/Km^2) × (16 m^2) × (317 K − 429 K)q ≈ - 2.01 kW[/tex]

Therefore, the rate of heat transfer by convection is approximately 2.01 kW.

To know more about convection:https://brainly.com/question/9382711

#SPJ11

Classes that serve one another or serve a purpose can be in a **package** (option D).

In Java, a package is a mechanism for organizing a collection of classes that are related to one another. Packages are used to prevent naming collisions, to enable efficient access control, and to provide an architecture for building reusable components.

Packages also aid in the organization of large systems by allowing related classes to be grouped together. Packages are an essential element of the Java programming language's design and are frequently used in Java development. Thus option D is the correct answer.

You can learn more about Java at

https://brainly.com/question/25458754

#SPJ11

The greatest amount of oil pollution comes from the large oil tanker accidents near ports and in rivers. The correct answer is option c.

Considering the various ways in which oil pollution can reach the North American oceans, the greatest amount of oil pollution comes from large oil tanker accidents near ports and in rivers. The oil tanker accidents occur because of the breaking of oil tankers while they are transporting oil to different countries through the ocean water.

The oil pollution results in severe damage to the aquatic life of the oceans. It is the largest cause of water pollution, which is why measures are taken by different environmental organizations to prevent oil pollution from reaching the oceans, leading to severe consequences on a global scale. The other sources of oil pollution are also harmful to the aquatic life, but the impact of large oil tanker accidents near ports and in rivers is greater than other sources.

Learn more about oil pollution here: https://brainly.com/question/28674739

#SPJ11

The groups which are rigid body are:

A bowling ball

A bowling ball

The group which system of rigid bodies:

A system of gears

A slider block system

A construction excavator's arm

The group which are system of non rigid bodies are:

A fishing pole

A diving board

A mechanical spring

A rigid body can be defined as state or condition whereby a body does not change shape. In order words, the distance between the two points on the body does not change when a body is being subjected to by an external force

Learn more about rigid bodies:

brainly.com/question/4057530

#SPJ12

Critical-thinking abilities link and arrange concepts. They are classified into three types: analysis, inference, and assessment. or count 0 to SIZE - 1 step 1

What is a case based approach?

Students are engaged in discussion of particular scenarios that approximate or are generally real-world examples while using a case-based method. This technique is learner-centered, with participants interacting intensely as they gain their knowledge and work as a group to investigate the case.

A crucial instance case focuses on a one-of-a-kind scenario with no specified aim. For example, a veteran suffering from severe PTSD may be examined in order to uncover strategies to alleviate his condition. Ethics play an important role in the case study process, and the majority of case studies require ethical approval.

Learn more about Critical-thinking

https://brainly.com/question/12980631

#SPJ1

When testing a four-wheel drive electronic component, the technician will use a scan tool to pull codes, and then a multimeter to diagnose any codes found.

A multimeter is an electronic measuring instrument that combines various measurement functions in one unit. A typical multimeter can measure voltage, current, and resistance. Analog multimeters have a microammeter whose pointer moves over a scale calibrated for all the various measurements that can be taken; digital instruments display digits on a screen; and, if equipped, an audio output for continuity and an auxiliary transducer input for temperature or capacitance measurement are also available. The multimeter's main purpose is to determine whether the electrical components and circuits are working correctly. To do so, the multimeter uses probes, which are the leads or wires connected to the tool. The black lead is connected to the COM (common) jack on the multimeter, while the red lead is connected to the VΩmA jack. When diagnosing codes found using a scan tool, it is important to use a multimeter to accurately diagnose the cause of the problem.

To learn more about Multimeter :

https://brainly.com/question/29838675

#SPJ11

Here is the required method in the U6_L2_Activity_Three class called `numDivisible` with two parameters: an integer value, num, followed by an array of int values. public static int numDivisible(int num, int[] arr){int count = 0;for (int i = 0; i < arr.length; i++) {if (arr[i] % num == 0) {count++;}}return count;}

The above method returns the number of elements in the array that are divisible by num. To test the above method, we can use the runner class which can take the inputs and display the output. Here is the required code for the runner class. It will ask the user for the inputs and then use the above-defined method to display the output.import java.util.*;public class Runner {public static void main(String[] args) {Scanner scan = new Scanner(System.in);int num = 0;System.out.println("Enter a value for num:");num = scan.nextInt();System.out.println("Enter array length:");int len = scan.nextInt();int[] arr = new int[len];System.out.println("Enter values:");for (int i = 0; i < len; i++) {arr[i] = scan.nextInt();}System.out.println("Num divisible by " + num + ": " + U6_L2_Activity_Three.numDivisible(num, arr));}}Note that the above code does not contain a main method to your code in the U6_L2_Activity_Three.java file or it will not be scored correctly.

In the U6_L2_Activity_Three class : https://brainly.com/question/30257619

#SPJ11