Explanation:
Pressure is the same for both plungers.
P = P
F / A = F / A
F / (¼ π d²) = F / (¼ π d²)
F / d² = F / d²
5 N / (0.05 m)² = F / (1 m)²
F = 2000 N
None of the options are correct.
You have a lightweight spring whose unstretched length is 4.0 cm. First, you attach one end of the spring to the ceiling and hang a 1.8 g mass from it. This stretches the spring to a length of 5.2 cm . You then attach two small plastic beads to the opposite ends of the spring, lay the spring on a frictionless table, and give each plastic bead the same charge. This stretches the spring to a length of 4.8 cm .
Required:
What is the magnitude of the charge (in nC) on each bead?
Answer:
The magnitude of the charge is 54.9 nC.
Explanation:
The charge on each bead can be found using Coulomb's law:
[tex] F_{e} = \frac{k*q_{1}q_{2}}{r^{2}} [/tex]
Where:
q₁ and q₂ are the charges, q₁ = q₂
r: is the distance of spring stretching = 4.8x10⁻² m
[tex]F_{e}[/tex]: is the electrostatic force
[tex] F_{e} = \frac{k*q^{2}}{r^{2}} \rightarrow q = \sqrt{\frac{F_{e}}{k}}*r [/tex]
Now, we need to find [tex]F_{e}[/tex]. To do that we have that Fe is equal to the spring force ([tex]F_{k}[/tex]):
[tex] F_{e} = F_{k} = -kx [/tex]
Where:
k is the spring constant
x is the distance of the spring = 4.8 - 4.0 = 0.8 cm
The spring constant can be found by equaling the sping force and the weight force:
[tex] F_{k} = -W [/tex]
[tex] -k*x = -m*g [/tex]
where x is 5.2 - 4.0 = 1.2 cm, m = 1.8 g and g = 9.81 m/s²
[tex] k = \frac{mg}{x} = \frac{1.8 \cdot 10^{-3} kg*9.81 m/s^{2}}{1.2 \cdot 10^{-2} m} = 1.47 N/m [/tex]
Now, we can find the electrostatic force:
[tex] F_{e} = F_{k} = -kx = -1.47 N/m*0.8 \cdot 10^{-2} m = -0.0118 N [/tex]
And with the magnitude of the electrostatic force we can find the charge:
[tex]q = \sqrt{\frac{F_{e}}{k}}*r = \sqrt{\frac{0.0118 N}{9 \cdot 10^{9} Nm^{2}/C^{2}}}*4.8 \cdot 10^{-2} m = 54.9 \cdot 10^{-9} C = 54.9 nC[/tex]
Therefore, the magnitude of the charge is 54.9 nC.
I hope it helps you!
The magnitude of the charge (in nC) on each bead is equal to 55.21 nC.
Given the following data:
Original length = 4.0 cm to m = 0.04 mMass = 1.8 grams to kg = 0.0018New length = 5.2 cm to m = 0.052.Final length = 4.8 cm to m = 0.048 m.Extension, e = [tex]0.052 - 0.048[/tex] = 0.012 m
Scientific data:
Acceleration due to gravity = 9.8 [tex]m/s^2[/tex]Coulomb's constant = [tex]8.99 \times 10^9\; Nm^2/C^2[/tex]To calculate the magnitude of the charge (in nC) on each bead, we would apply Coulomb's law:
First of all, we would determine the spring constant of this lightweight spring by using this formula:
[tex]W = mg = Ke \\\\K=\frac{mg}{e} \\\\K=\frac{0.0018 \times 9.8}{0.012} \\\\K=\frac{0.01764}{0.012}[/tex]
Spring constant, K = 1.47 N/m.
For the electrostatic force:
[tex]F = ke\\\\F = 1.47 \times 0.08[/tex]
F = 0.01176 Newton.
Coulomb's law of electrostatic force.
Mathematically, the charge in an electric field is given by this formula:
[tex]q = \sqrt{\frac{F}{k} } \times r[/tex]
Substituting the given parameters into the formula, we have;
[tex]q = \sqrt{\frac{0.01176 }{8.99 \times 10^9} } \times 0.048\\\\q=\sqrt{1.3228 \times 10^{-12}} \times 0.048\\\\q=1.1502 \times 10^{-6} \times 0.048\\\\q= 5.521 \times 10^{-8}\;C[/tex]
Note: 1 nC = [tex]1 \times 10^{-9}\;C[/tex]
Charge, q = 55.21 nC.
Read more on electric field here: https://brainly.com/question/14372859
"Two waves of the same frequency have amplitudes 1.00 and 2.00. They interfere at a point where their phase difference is 60.0°. What is the resultant amplitude?"
Answer:
The resultant amplitude of the two waves is 2.65.
Explanation:
Given;
amplitude of the first wave, A₁ = 1
amplitude of the second wave, A₂ = 2
phase difference of the two amplitudes, θ = 60.0°.
The resultant amplitude of two waves after interference is given by;
[tex]A = \sqrt{A_1^2 + A_2^2 + 2A_1A_2Cos \theta} \\\\A = \sqrt{1^2 + 2^2 + 2(1)(2)Cos 60} \\\\A= 2.65[/tex]
Therefore, the resultant amplitude of the two waves is 2.65.
The resistor used in the procedures has a manufacturer's stated tolerance (percent error) of 5%. Did you results from Data Table agree with the manufacturer's statement? Explain.
Resistor Measured Resistance
100 99.1
Answer:
e% = 0.99% this value is within the 5% tolerance given by the manufacturer
Explanation:
Modern manufacturing methods establish a tolerance in order to guarantee homogeneous characteristics in their products, in the case of resistors the tolerance or error is given by
e% = | R_nominal - R_measured | / R_nominal 100
where R_nominal is the one written in the resistance in your barcode, R_measured is the real value read with a multimeter and e% is the tolerance also written in the resistors
let's apply this formula to our case
R_nominal = 10 kΩ = 10000 Ω
R_measured = 100 99 Ω
e% = | 10000 - 10099.1 | / 10000 100
e% = 0.99%
this value is within the 5% tolerance given by the manufacturer
The rectangular plate is tilted about its lower edge by a cable tensioned at a constant 600 N. Determine and plot the moment of this tension about the lower edge AB of the plate for the range 0 ≤ θ ≤ 90°
Answer:
Explanation:
From the figure , it is clear that moment of tension is balanced by moment of weight of plate about the line AB which is acting as axis . If W be the weight of plate ,
moment of tension about AB = moment of weight W about line AB
= W x 2.5 cosθ
moment of tension about AB = 2.5 W cosθ
here only variable is cosθ which changes when θ changes
So, moment of tension about AB varies according to cosθ.
When θ = 0
moment of tension about AB = 2.5 W x cos 0 = 2.5 W . It is the maximum value of moment of tension .
When θ = 90°
moment of tension about AB = 2.5 W cos 90 = 0
moment of tension about AB = 0
So graph of moment of tension about AB will vary according to graph of
cosθ . It has been shown in the file attached .
Find an analytic expression for p(V)p(V)p(V), the pressure as a function of volume, during the adiabatic expansion.
Answer:
In an adiabatic process we have
pV γ = const..
This explains that the pressure is a function of volume, p ( V ) ,
So can be written as:
p ( V ) × V γ = p 0 V γ 0 ,
or p ( V ) = p 0 V 0 / V γ
= p 0 V 0 / V ^(7 / 5)
An isolated system consists of two masses. The first, m1, has a mass of 1.90 kg, and is initially traveling to the east with a speed of 6.71 m/s. The second, m2, has a mass of 2.94 kg, and is initially traveling to the west with an unknown initial speed. The two masses collide head-on in a completely inelastic collision that stops them both. Calculate the initial kinetic energy of m2.
Answer:
m1v1=m2v2, v2=4.3m/s KE=(0.5)(2.94)(4.3)=6.2J
If mirror M2 in a Michelson interferometer is moved through 0.233 mm, a shift of 792 bright fringes occurs. What is the wavelength of the light producing the fringe pattern?
Answer:
The wavelength is [tex]\lambda = 589 nm[/tex]
Explanation:
From the question we are told that
The distance of the mirror shift is [tex]k = 0.233 \ mm = 0.233*10^{-3} \ m[/tex]
The number of fringe shift is n = 792
Generally the wavelength producing this fringes is mathematically represented as
[tex]\lambda = \frac{ 2 * k }{ n }[/tex]
substituting values
[tex]\lambda = \frac{ 2 * 0.233*10^{-3} }{ 792 }[/tex]
[tex]\lambda = 5.885 *10^{-7} \ m[/tex]
[tex]\lambda = 589 nm[/tex]
n ultraviolet light beam having a wavelength of 130 nm is incident on a molybdenum surface with a work function of 4.2 eV. How fast does the electron move away from the metal
Answer:
The speed of the electron is 1.371 x 10⁶ m/s.
Explanation:
Given;
wavelength of the ultraviolet light beam, λ = 130 nm = 130 x 10⁻⁹ m
the work function of the molybdenum surface, W₀ = 4.2 eV = 6.728 x 10⁻¹⁹ J
The energy of the incident light is given by;
E = hf
where;
h is Planck's constant = 6.626 x 10⁻³⁴ J/s
f = c / λ
[tex]E = \frac{hc}{\lambda} \\\\E = \frac{6.626*10^{-34} *3*10^{8}}{130*10^{-9}} \\\\E = 15.291*10^{-19} \ J[/tex]
Photo electric effect equation is given by;
E = W₀ + K.E
Where;
K.E is the kinetic energy of the emitted electron
K.E = E - W₀
K.E = 15.291 x 10⁻¹⁹ J - 6.728 x 10⁻¹⁹ J
K.E = 8.563 x 10⁻¹⁹ J
Kinetic energy of the emitted electron is given by;
K.E = ¹/₂mv²
where;
m is mass of the electron = 9.11 x 10⁻³¹ kg
v is the speed of the electron
[tex]v = \sqrt{\frac{2K.E}{m} } \\\\v = \sqrt{\frac{2*8.563*10^{-19}}{9.11*10^{-31}}}\\\\v = 1.371 *10^{6} \ m/s[/tex]
Therefore, the speed of the electron is 1.371 x 10⁶ m/s.
A mass m = 0.6 kg is released from rest at the top edge of a hemispherical bowl with radius = 1.1 meters. The mass then slides without friction down the inner surface toward the bottom of the bowl. At a certain point of its path the mass achieves a speed v = 3.57 m/s. At this point, what angle \theta\:θ ( in degrees) does the mass make with the top of the bowl?
Answer:
The angle is [tex]\theta = 36.24 ^o[/tex]
Explanation:
From the question we are told that
The mass is [tex]m = 0.6 \ kg[/tex]
The radius is [tex]r = 1.1 \ m[/tex]
The speed is [tex]v = 3.57 \ m /s[/tex]
According to the law of energy conservation
The potential energy of the mass at the top is equal to the kinetic energy at the bottom i.e
[tex]m * g * h = \frac{1}{2} * m * v^2[/tex]
=> [tex]h = \frac{1}{2 g } * v^2[/tex]
Here h is the vertical distance traveled by the mass which is also mathematically represented as
[tex]h = r * sin (\theta )[/tex]
So
[tex]\theta = sin ^{-1} [ \frac{1}{2* g* r } * v^2][/tex]
substituting values
[tex]\theta = sin ^{-1} [ \frac{1}{2* 9.8* 1.1 } * (3.57)^2][/tex]
[tex]\theta = 36.24 ^o[/tex]
Two protons, A and B, are next to an infinite plane of positive charge. Proton B is twice as far from the plane as proton A. Which proton has the larg
Answer:
They both have the same acceleration
You simultaneously shine two light beams, each of intensity I0, on an ideal polarizer. One beam is unpolarized, and the other beam is polarized at an angle of exactly 30.0∘ to the polarizing axis of the polarizer. Find the intensity of the light that emerges from the polarizer. Express your answer in term of I0 .
Answer:
The emerging intensity is equal to 0.75[tex]I_{o}[/tex]
Explanation:
The initial intensity of the light = [tex]I_{o}[/tex]
The angle of polarization β = 30°
We know that the polarized light intensity is related to the initial light intensity by
[tex]I[/tex] = [tex]I_{0} cos^{2}\beta[/tex]
where [tex]I[/tex] is the emerging polarized light intensity
inserting values gives
[tex]I[/tex] = [tex]I_{0} cos^{2}[/tex] 30°
[tex]cos^{2}[/tex] 30° = [tex](cos 30)^{2}[/tex] = [tex](\frac{\sqrt{3} }{2} )^{2}[/tex] = 0.75
[tex]I[/tex] = 0.75[tex]I_{o}[/tex]
A father and his young son get on a teeter-totter. The son sits 2 m fromthe center, but the father has to sit closer to balance. Where does the father have to sit to balance the teeter-totter if he weighs 4 times as much as his son?
Answer:
The distance of the father from the center is [tex]d_f = \frac{1}{2} \ m[/tex]
Explanation:
From the question we are told that
The distance of the son from the center is [tex]d_s = 2 \ m[/tex]
Let the mass of the son be [tex]m_s[/tex]
then the mass of the father is [tex]m_f = 4m_s[/tex]
Now for the teeter-totter to be balanced the torque due to the weight of the father must be equal to the torque due to the weight the son, this is mathematically represented as
[tex]\tau_s = \tau_f[/tex]
Where [tex]\tau_s[/tex] is the torque of the son which is mathematically represented as
[tex]\tau_ s = m_s * d_s * g[/tex]
while [tex]\tau_f[/tex] is the torque of the father which is mathematically represented as
[tex]\tau_f = m_f * d_f * g[/tex]
=> [tex]\tau_f = 4 m_s * d_f * g[/tex]
So
[tex]4 m_s * d_f * g = m_s * d_s * g[/tex]
substituting values
[tex]4 * d_f * = 2[/tex]
=> [tex]d_f = \frac{1}{2} \ m[/tex]
Sammy is 5 feet and 5.3 inches tall. What is Sammy's height in inches?
Answer:
[tex]\boxed{\sf 65.3 \ inches}[/tex]
Explanation:
1 foot = 12 inches
Sammy is 5 feet tall.
5 feet = ? inches
Multiply the feet value by 12 to find in inches.
5 × 12
= 60
Add 5.3 inches to 60 inches.
60 + 5.3
= 65.3
Distinguish between physical and chemical changes. Include examples in your explanations.
Answer:
Chemical changes are recognized when a substance changes its properties permanently and it cannot be the same substance as before.
Instead the physical changes implies that if you can return to the same substance through a reverse process.
Explanation:
A chemical change is, by example, a combustion, if a sheet of paper burns, its result is ashes, the ashes cannot go back to being a sheet of paper because its properties changed, heat energy was generated that changed matter permanently.
A physical change, by example, is that of freezing water, the water becomes ice, but this can easily become water again if the temperature is increased, its properties do not change and the chemistry of the substance does not change.
A chemical change takes place when a chemical reaction takes place, while when a matter changes forms but not the chemical identity then a physical change takes place.
• A product or a new compound formation takes place from a chemical change as the rearrangement of atoms takes place to produce novel chemical bonds.
• In a chemical change always a chemical reaction takes place.
• Some of the chemical changes examples are souring milk, burning wood, digesting food, mixing acid and base, cooking food, etc.
• In a physical change no new chemical species form.
• The changing of the state of a pure substance between liquid, gas, or solid is a physical change as there is no change in the identity of the matter.
• Some of the physical changes are melting of ice, tempering of steel, breaking a bottle, crumpling a sheet of aluminum foil, boiling water, and shredding paper.
Thus, a new substance is formed during a chemical change, while a physical change does not give rise to a new substance.
To know more about:
https://brainly.com/question/7279398
The Bohr model pictures a hydrogen atom in its ground state as a proton and an electron separated by the distance a0 = 0.529 × 10−10 m. The electric potential created by the electron at the position of the proton is
Answer:
E = -8.23 10⁻¹⁷ N / C
Explanation:
In the Bohr model, the electric potential for the ground state corresponding to the Bohr orbit is
E = k q₁ q₂ / r²
in this case
q₁ is the charge of the proton and q₂ the charge of the electron
E = - k e² / a₀²
let's calculate
E = - 9 10⁹ (1.6 10⁻¹⁹)² / (0.529 10⁻¹⁰)²
E = -8.23 10⁻¹⁷ N / C
Radio station WCCO in Minneapolis broadcasts at a frequency of 830 kHz. At a point some distance from the transmitter, the magnetic-field amplitude of the electromagnetic wave from WCCO is 4.82×10-11 T.A) Calculate the wavelength.B) Calculate the wave number.C) Calculate the angular frequency.
D) Calculate the electric-field amplitude.
Answer:
A
[tex]\lambda = 361.45 \ m[/tex]
B
[tex]k = 0.01739 \ rad/m[/tex]
C
[tex]w = 5.22 *10^{6} \ rad/s[/tex]
D
[tex]E = 0.01446 \ N/C[/tex]
Explanation:
From the question we are told that
The frequency is [tex]f = 83 0 \ kHz = 830 *10^{3} \ Hz[/tex]
The magnetic field amplitude is [tex]B = 4.82*10^{-11} \ T[/tex]
Generally wavelength is mathematically represented as
[tex]\lambda = \frac{c}{f}[/tex]
where c is the speed of light with value [tex]c = 3.0*10^{8} \ m/s[/tex]
=> [tex]\lambda = \frac{3.0*10^{8}}{ 830 *10^{3}}[/tex]
=> [tex]\lambda = 361.45 \ m[/tex]
Generally the wave number is mathematically represented as
[tex]k = \frac{2 \pi }{\lambda }[/tex]
=> [tex]k = \frac{2 * 3.142 }{ 361.45 }[/tex]
=> [tex]k = 0.01739 \ rad/m[/tex]
Generally the angular frequency is mathematically represented as
[tex]w = 2 * \pi * f[/tex]
=> [tex]w = 2 * 3.142 * 830*10^{3}[/tex]
=> [tex]w = 5.22 *10^{6} \ rad/s[/tex]
The the electric-field amplitude is mathematically represented as
[tex]E = B * c[/tex]
=> [tex]E = 4.82 *10^{-11} * 3.0*10^{8}[/tex]
=> [tex]E = 0.01446 \ N/C[/tex]
This question involves the concepts of wavelength, frequency, wave number, and electric field.
a) The wavelength is "361.44 m".
b) The wave number is "0.0028 m⁻¹".
c) The angular frequency is "5.22 x 10⁶ rad/s".
d) The electric field amplitude is "0.0145 N/C".
a)
The wavelength can be given by the following formula:
[tex]c=f\lambda[/tex]
where,
c = speed of light = 3 x 10⁸ m/s
f = frequency = 830 KHz = 8.3 x 10⁵ Hz
λ = wavelength = ?
Therefore,
[tex]3\ x\ 10^8\ m/s=(8.3\ x\ 10^5\ Hz)\lambda\\\\\lambda=\frac{3\ x\ 10^8\ m/s}{8.3\ x\ 10^5\ Hz}\\\\[/tex]
λ = 361.44 m
b)
The wave number can be given by the following formula:
[tex]wave\ number = \frac{1}{\lambda} = \frac{1}{361.44\ m}[/tex]
wave number = 0.0028 m⁻¹
c)
The angular frequency is given as follows:
[tex]\omega = 2\pi f = (2)(\pi)(8.3\ x\ 10^5\ Hz)[/tex]
ω = 5.22 x 10⁶ rad/s
d)
The electric field amplitude can be given by the following formula:
[tex]\frac{E}{B} = c\\\\c(B)=E\\\\E = (3\ x\ 10^8\ m/s)(4.82\ x\ 10^{-11}\ T)\\[/tex]
E = 0.0145 N/C
Learn more about wavelength and frequency here:
https://brainly.com/question/12924624?referrer=searchResults
A brick weighs 50.0 N, and measures 30.0 cm × 10.0 cm × 4.00 cm. What is the maximum pressure it can exert on a horizontal surface due to its weight?
Answer:
Pressure, P = 1250 Pa
Explanation:
Given that,
Weight of a brick, F = 50 N
Dimension of the brick is 30.0 cm × 10.0 cm × 4.00 cm
We need to find the maximum pressure it can exert on a horizontal surface due to its weight. Pressure is equal to the force acting per unit area. Pressure exerted is inversely proportional to the area of cross section. So, we need to minimize area. Taking to smaller dimensions.
A = 40 cm × 10 cm = 400 cm² = 0.04 m²
So,
Pressure,
[tex]P=\dfrac{50\ N}{0.04\ m^2}\\\\P=1250\ Pa[/tex]
So, the maximum pressure of 1250 Pa it can exert on a horizontal surface.
The maximum pressure it can exert on a horizontal surface due to its weight will be 1250 Pascal.
What is pressure?The force applied perpendicular to the surface of an item per unit area across which that force is spread is known as pressure. It is denoted by P.
The given data in the problem is;
W is the weight of a brick = 50 N
The dimension of the brick = 30.0 cm × 10.0 cm × 4.00 cm
A is the area,
The area is found as;
A=40 cm × 10 cm = 400 cm² = 0.04 m²
The pressure is the ratio of the force and area
[tex]\rm P = \frac{F}{A} \\\\ \rm P = \frac{50}{0.04} \\\\ \rm P =1250 \ Pascal[/tex]
Hence the maximum pressure it can exert on a horizontal surface due to its weight will be 1250 Pascal.
To learn more about the pressure refer to the link;
https://brainly.com/question/356585
A stone is dropped from the bridge, it takes 4s to reach the water. what's the height of the bridge?
Explanation:
Using Equations of Motion :
[tex]s = ut + \frac{1}{2} g {t}^{2} [/tex]
Height = 0 * 4 + 4.9 * 16
Height = 78.4 m
The cylinder is displaced 0.17 m downward from its equilibrium position and is released at time t = 0. Determine the displacement y and the velocity v when t = 3.1 s. The displacement and velocity are positive if downward, negative if upward. What is the magnitude of the maximum acceleration?
Complete Question
The image of this question is shown on the first uploaded image
Answer:
a
[tex]d =0.161 \ m[/tex]
b
[tex]v = - 0.054 \ m/s[/tex]
c
[tex]a = 6.12 \ m/s^2[/tex]
Explanation:
From the question we are told that
The maximum displacement is A = 0.17 m
The time considered is [tex]t = 3.1 \ s[/tex]
The spring constant is [tex]k = 137 \ N \cdot m[/tex]
The mass is [tex]m = 3.8 \ kg[/tex]
Generally given that the motion which the cylinder is undergoing is a simple harmonic motion , then the displacement is mathematically represented as
[tex]d = A cos (w t )[/tex]
Where [tex]w[/tex] is the angular frequency which is mathematically evaluated as
[tex]w = \sqrt{\frac{k}{m} }[/tex]
substituting values
[tex]w = \sqrt{\frac{137}{ 3.8} }[/tex]
[tex]w =6[/tex]
So the displacement is at t
[tex]d = 0.17 cos (6 * 3.1 )[/tex]
[tex]d =0.161 \ m[/tex]
Generally the velocity of a SHM(simple harmonic motion) is mathematically represented as
[tex]v = - Asin (wt)[/tex]
substituting values
[tex]v = - 0.17 sin ( 6 * 3.1 )[/tex]
[tex]v = - 0.054 \ m/s[/tex]
Generally the maximum acceleration is mathematically represented as
[tex]a = w^2 * A[/tex]
substituting values
[tex]a_{max} = 6^2 * (0.17)[/tex]
substituting values
[tex]a = 6^2 * (0.17)[/tex]
[tex]a = 6.12 \ m/s^2[/tex]
In a double-slit experiment the distance between slits is 5.0 mm and the slits are 1.4 m from the screen. Two interference patterns can be seen on the screen: one due to light of wavelength 450 nm, and the other due to light of wavelength 590 nm. What is the separation in meters on the screen between the m = 5 bright fringes of the two interference patterns?
Answer:
Δy = 1 10⁻⁴ m
Explanation:
In double-slit experiments the constructive interference pattern is described by the equation
d sin θ = m λ
In this case we have two wavelengths, so two separate patterns are observed, let's use trigonometry to find the angle
tan θ = y / L
as the angles are small,
tan θ = sin θ / cos θ = sin θ
substituting
sin θ = y / L
d y / L = m λ
y = m λ / d L
let's apply this formula for each wavelength
λ = 450 nm = 450 10⁻⁹ m
m = 5
d = 5.0 mm = 5.0 10⁻³ m
y₁ = 5 450 10⁻⁹ / (5 10⁻³ 1.4)
y₁ = 3.21 10⁻⁴ m
we repeat the calculation for lam = 590 nm = 590 10⁻⁹ m
y₂ = 5 590 10⁻⁹ / (5 10⁻³ 1.4)
y₂= 4.21 10⁻⁴ m
the separation of these two lines is
Δy = y₂ - y₁
Δy = (4.21 - 3.21) 10⁻⁴ m
Δy = 1 10⁻⁴ m
Question 2
A) A spring is compressed, resulting in its displacement to the right. What happens to the spring when it is released? (1 point)
The spring exerts a restoring force to the right and compresses even further
The spring exerts a restoring force to the left and returns to its equilibrium position
The spring exerts a restoring force to the right and returns to its equilibrium position
The spring exerts a restoring force to the left and stretches beyond its equilibrium position
1. Which example best describes a restoring force?
B) the force applied to restore a spring to its original length
2. A spring is compressed, resulting in its displacement to the right. What happens to the spring when it is released?
C) The spring exerts a restoring force to the left and returns to its equilibrium position.
3. A 2-N force is applied to a spring, and there is displacement of 0.4 m. How much would the spring be displaced if a 5-N force was applied?
D) 1 m
4. Hooke’s law is described mathematically using the formula Fsp=−kx. Which statement is correct about the spring force, Fsp?
D)It is a vector quantity.
5. What happens to the displacement vector when the spring constant has a higher value and the applied force remains constant?
A) It decreases in magnatude.
A 1.2-m length of wire centered on the origin carries a 20-A current directed in the positive y direction. Determine the magnetic field at the point x= 5.0m on x-axis.
a. 1.6 nt in the negative z direction
b. 1.6 nt in the positive z direction
c. 2.4 T in the positive z direction
d. 2.4 nt in the negative z direction
e. None of the above
Answer:
None of the above
Explanation:
The formula of the magnetic field of a point next to a wire with current is:
B = 2×10^(-7) × ( I /d)
I is the intensity of the current.
d is the distance between the wire and the point.
● B = 2*10^(-7) × (20/5) = 8 ×10^(-7) T
A metal sphere A of radius a is charged to potential V. What will be its potential if it is enclosed by a spherical conducting shell B of radius b and the two are connected by a wire?
Answer:
The potential will be Va/b
Explanation:
So Let sphere A charged Q to potential V.
so, V= KQ/a. ....(1
Thus, spherical shell B is connected to the sphere A by a wire, so all charge always reside on the outer surface.
therefore, potential will be ,
V ′ = KQ/b = Va/b... That is from .....(1), KQ=Va]
3. What conclusion can you make about the electric field strength between two parallel plates? Explain your answer referencing Photo 2.
Answer:
From the relation above we can conclude that the as the distance between the two plate increases the electric field strength decreases
Explanation:
I cannot find any attached photo, but we can proceed anyways theoretically.
The electric field strength (E) at any point in an electric field is the force experienced by a unit positive charge (Q) at that point
i.e
[tex]E=\frac{F}{Q}[/tex]
But the force F
[tex]F= \frac{kQ1Q2}{r^2}[/tex]
But the electric field intensity due to a point charge Q at a distance r meters away is given by
[tex]E= \frac{\frac{kQ1Q2}{r^2}}{Q} \\\\\E= \frac{Q1}{4\pi er^2 }[/tex]
From the relation above we can conclude that the as the distance between the two plate increases the electric field strength decreases
Without actually calculating any logarithms, determine which of the following intervals the sound intensity level of a sound with intensity 3.66×10^−4W/m^2 falls within?
a. 30 and 40
b. 40 and 50
c. 50 and 60
d. 60 and 70
e. 70 and 80
f. 80 and 90
g. 90 and 100
Answer:
f. 80 and 90
Explanation:
1 x 10⁻¹² W/m² sound intensity falls within 0 sound level
1 x 10⁻¹¹ W/m² sound intensity falls within 10 sound level
1 x 10⁻¹⁰ W/m² sound intensity falls within 20 sound level
1 x 10⁻⁹ W/m² sound intensity falls within 30 sound level
1 x 10⁻⁸ W/m² sound intensity falls within 40 sound level
1 x 10⁻⁷ W/m² sound intensity falls within 50 sound level
1 x 10⁻⁶ W/m² sound intensity falls within 60 sound level
1 x 10⁻⁵ W/m² sound intensity falls within 70 sound level
1 x 10⁻⁴ W/m² sound intensity falls within 80 sound level
1 x 10⁻³ W/m² sound intensity falls within 90 sound level
Given sound intensity (3.66 x 10⁻⁴ W/m²) falls with 1 x 10⁻⁴ W/m² of intensity which is within 80 and 90 sound level.
f. 80 and 90
Suppose we want to calculate the moment of inertia of a 56.5 kg skater, relative to a vertical axis through their center of mass.
Required:
a. First calculate the moment of inertia (in kg-m^2) when the skater has their arms pulled inward by assuming they are cylinder of radius 0.11 m.
b. Now calculate the moment of inertia of the skater (in kg-m^2) with their arms extended by assuming that each arm is 5% of the mass of their body. Assume the body is a cylinder of the same size, and the arms are 0.875 m long rods extending straight out from their body being rotated at the ends.
Answer:
a. 0.342 kg-m² b. 2.0728 kg-m²
Explanation:
a. Since the skater is assumed to be a cylinder, the moment of inertia of a cylinder is I = 1/2MR² where M = mass of cylinder and r = radius of cylinder. Now, here, M = 56.5 kg and r = 0.11 m
I = 1/2MR²
= 1/2 × 56.5 kg × (0.11 m)²
= 0.342 kgm²
So the moment of inertia of the skater is
b. Let the moment of inertia of each arm be I'. So the moment of inertia of each arm relative to the axis through the center of mass is (since they are long rods)
I' = 1/12ml² + mh² where m = mass of arm = 0.05M, l = length of arm = 0.875 m and h = distance of center of mass of the arm from the center of mass of the cylindrical body = R/2 + l/2 = (R + l)/2 = (0.11 m + 0.875 m)/2 = 0.985 m/2 = 0.4925 m
I' = 1/12 × 0.05 × 56.5 kg × (0.875 m)² + 0.05 × 56.5 kg × (0.4925 m)²
= 0.1802 kg-m² + 0.6852 kg-m²
= 0.8654 kg-m²
The total moment of inertia from both arms is thus I'' = 2I' = 1.7308 kg-m².
So, the moment of inertia of the skater with the arms extended is thus I₀ = I + I'' = 0.342 kg-m² + 1.7308 kg-m² = 2.0728 kg-m²
a) The moment of inertia as the skater pulled his/her arm inward by assuming he/she is a cylinder is 0.3418kg-m².
b) If the body of the skater is assumed to be a cylinder of the same size, and the arms are rods extending straight out from his/her body being rotated at the ends, the moment of inertia is 1.7495kg-m².
Given the data in the question;
Mass of skater; [tex]M = 56.5kg[/tex]
a)
When the skater has his arms pulled inward by assuming they are cylinder of radius; [tex]R = 0.11 m[/tex]
Moment of inertia; [tex]I = \ ?[/tex]
From Parallel axis theorem; Moment of Inertia for a cylindrical body is expressed:
[tex]I = \frac{1}{2}MR^2[/tex]
Where M is the mass and R is the radius
We substitute our given values into the equation
[tex]I = \frac{1}{2}\ *\ 56.5kg\ *\ (0.11m)^2\\\\I = \frac{1}{2}\ *\ 56.5kg\ *\ 0.0121m^2\\\\I = 0.3418kg.m^2[/tex]
Therefore, the moment of inertia as the skater pulled his/her arm inward by assuming he/she is a cylinder is 0.3418kg-m²
b)
With the skater's arms extended by assuming that each arm is 5% of the mass of their body
Mass of each arm; [tex]M_a = \frac{5}{100} * M = \frac{5}{100} * 56.5kg = 2.825kg[/tex]
Remaining mass; [tex]M_b = M - 2M_a = 56.5kg - 2(2.825kg) = 50.85kg[/tex]
Assume the body is a cylinder of the same size and the arms are 0.875 m long rods extending straight out from their body being rotated at the ends.
Length of arm; [tex]L = 0.875 m[/tex]
From Parallel axis theorem; Moment of Inertia about vertical axis is expressed as:
[tex]I = \frac{1}{2}M_bR^2 + \frac{2}{3}M_aL^2[/tex]
We substitute in our values
[tex]I = \frac{1}{2}*50.85kg*(0.11m)^2 + \frac{2}{3}*2.825kg*(0.875m)^2\\\\I = [\frac{1}{2}*50.85kg * 0.0121m^2] + [\frac{2}{3}*2.825kg*0.765625m^2]\\\\I = 0.3076kg.m^2 + 1.4419kg.m^2\\\\I = 1.7495kg.m^2[/tex]
Therefore, if the body of the skater is assumed to be a cylinder of the same size, and the arms are rods extending straight out from his/her body being rotated at the ends, the moment of inertia is 1.7495kg-m².
Learn more: https://brainly.com/question/6897330
please help !!!!!!!!!!
Answer:
Lighthouse 1 during the day will be warmer, lighthouse 2 during the night will be warmer.
Explanation:
As the paragraph stated land absorbs heat and heats up faster than water. So during the day the lighthouse farthest away from the water will be hotter. But then the converse is true also land losses heat faster than water at night. So the water retains the heat from the day better making the lighthouse by the water warmer at night.
g Can a rigid body experience any ACCELERATION when the resultant force acting on that rigid body is zero? Explain.Can a rigid body experience any ACCELERATION when the resultant force acting on that rigid body is zero? Explain.
Answer:
No, a rigid body cannot experience any acceleration when the resultant force acting on the body is zero.
Explanation:
If the net force on a body is zero, then it means that all the forces acting on the body are balanced and cancel out one another. This sate of equilibrium can be static equilibrium (like that of a rigid body), or dynamic equilibrium (that of a car moving with constant velocity)
For a body under this type of equilibrium,
ΣF = 0 ...1
where ΣF is the resultant force (total effective force due to all the forces acting on the body)
For a body to accelerate, there must be a force acting on it. The acceleration of a body is proportional to the force applied, for a constant mass of the body. The relationship between the net force and mass is given as
ΣF = ma ...2
where m is the mass of the body
a is the acceleration of the body
Substituting equation 2 into equation 1, we have
0 = ma
therefore,
a = 0
this means that if the resultant force acting on a rigid body is zero, then there won't be any force available to produce acceleration on the body.
A square coil of wire with 15 turns and an area of 0.40 m2 is placed parallel to a magnetic field of 0.75 T. The coil is flipped so its plane is perpendicular to the magnetic field in 0.050 s. What is the magnitude of the average induced emf
Answer:
The magnitude of the average induced emf is 90V
Explanation:
Given;
area of the square coil, A = 0.4 m²
number of turns, N = 15 turns
magnitude of the magnetic field, B = 0.75 T
time of change of magnetic field, t = 0.05 s
The magnitude of the average induced emf is given by;
E = -NAB/t
E = -(15 x 0.4 x 0.75) / 0.05
E = -90 V
|E| = 90 V
Therefore, the magnitude of the average induced emf is 90V
If Superman really had x-ray vision at 0.12 nm wavelength and a 4.1 mm pupil diameter, at what maximum altitude could he distinguish villains from heroes, assuming that he needs to resolve points separated by 5.4 cm to do this?
Answer:
Maximum altitude to see(L) = 1.47 × 10⁶ m (Approx)
Explanation:
Given:
wavelength (λ) = 0.12 nm = 0.12 × 10⁻⁹ m
Pupil Diameter (d) = 4.1 mm = 4 × 10⁻³ m
Separation distance (D) = 5.4 cm = 0.054 m
Find:
Maximum altitude to see(L)
Computation:
Resolving power = 1.22(λ / d)
D / L = 1.22(λ / d)
0.054 / L = 1.22 [(0.12 × 10⁻⁹) / (4 × 10⁻³ m)]
0.054 / L = 1.22 [0.03 × 10⁻⁶]
L = 0.054 / 1.22 [0.03 × 10⁻⁶]
L = 0.054 / [0.0366 × 10⁻⁶]
L = 1.47 × 10⁶
Maximum altitude to see(L) = 1.47 × 10⁶ m (Approx)
