nec 430.6(a)(1) requires that the motor full-load amperes listed in tables 430.247 through 430.250 be used to size all of the following, except for_______ .

Answers

Answer 1

.nec 430.6(a)(1) requires that the motor full-load amperes listed in tables 430.247 through 430.250 be used to size all of the following, except for Motor Voltage.

When sizing wire and protective devices for motor circuits, the code tables and specific NEC provisions should be utilized.

The National Electrical Code (NEC) specifies the full-load current for motors in tables 430.247 through 430.250.

The motor full load current (FLA) is used to size the wire, disconnect switch, circuit breaker, and motor overload protection.

It's worth noting that motor voltage is not part of this listing. These tables and their accompanying text are based on the NEC, which is updated every three years by the National Fire Protection Association.

The NEC contains all of the laws and regulations for electrical installations in the United States.

To know more about motor voltage: https://brainly.com/question/25543272

#SPJ11


Related Questions

Which of the following statements are true? Choose all that apply.- The magnetic force is always perpendicular to both the magnetic field and the velocity of the charge .- Magnetic fields cause charges to speed up.- Magnetic fields are created by moving charges.- Magnetic fields don't do any work on charges.- The magnetic field is always perpendicular to the velocity of the charge.- Magnetic fields deflect moving charges.

Answers

The following statements are true:

The magnetic force is always perpendicular to both the magnetic field and the velocity of the charge.Magnetic fields don't do any work on charges.Magnetic fields deflect moving charges.

Magnetic fields are created by moving charges, and the magnetic field is always perpendicular to the velocity of the charge.


The magnetic force is always perpendicular to both the magnetic field and the velocity of the charge. The magnetic force is always perpendicular to both the magnetic field and the velocity of the charge. Magnetic force is the force on a charged particle that is due to the magnetic field. The magnetic force is always perpendicular to both the magnetic field and the velocity of the charge. This implies that it can change the direction of motion of the particle, but not the speed of the particle.

Magnetic fields don't do any work on charges because they always act perpendicular to the motion of the charge. Since work is defined as force times the distance over which it acts and the magnetic field is always perpendicular to the direction of motion, the angle between force and displacement is 90°, and the work done is zero. Magnetic fields deflect moving charges. Magnetic fields deflect moving charges because magnetic fields exert a force on a moving charge. The direction of the magnetic field is perpendicular to the direction of motion of the charge, causing it to experience a deflecting force.

You can learn more about the magnetic force at: https://brainly.co.id/tugas/50355801

#SPJ11

A student walks 1.0 kilometer due east and 1.0 kilometer due south. Then
she runs 2.0 kilometers due west. The magnitude of the student's
resultant displacement is closestto
A. 3.4 km
B. 1.4 km
C. 4.0 km
D. O km

Answers

The resulting displacement will be 3.4 km. The correct option is A.

How to calculate the displacement?

The displacement is calculated by finding the displacement from east to west, which is 2.0 km, and subtracting the displacement from north to south, which is 1.0 km.

A student walks 1.0 kilometers due east and 1.0 kilometers due south. Then she runs 2.0 kilometers due west. The magnitude of the student's resultant displacement is closest to 3.4 km.

To begin with, we may use the Pythagorean Theorem to determine the resultant displacement's magnitude. The Pythagorean Theorem is a formula that is used to determine the length of a right triangle's sides when one is missing. This theorem is used to calculate the magnitude of the resultant displacement, which is a quantity. It's a good idea to draw a diagram to help you understand the problem.

Here's a rough sketch of the scenario: We will now apply the Pythagorean theorem in this way: The resultant displacement's magnitude is 3.4 kilometers. Thus, the correct option is A.

To know more about displacement follow

https://brainly.com/question/14637077

#SPJ11

what will happen to the excess electrons when the negatively charged rod touches the metal sphere?

Answers

If the metal sphere is positively charged, then the excess electrons will move to the metal sphere. But if it's negatively charged, the excess electrons will repel the metal sphere.

a density bottle has a mass of 0.04kg when empty a mass of 0.20kg when some quality of steel ball bearing is added to it and a mass of 0.24kg when the remainder of the bottle is filled with water. if the density bottle weight 0.1kg when filled with water. calculate the relative density of the steel ball bearing.​

Answers

Answer:

Bottle                 =               .04

Bottle + Bearing    =            .20

Bottle + Bearing + Water = .24

Bottle + Water =                   .1

Full bottle of water weighs  =  .06

Weight of bearing    =           .16

What volume  of water does the bearing replace????

It takes .14 of bottle to replace bearing leaving .06 of water

Density = 16 / 6 = 2.67

Check:     probably should use volumes

open the experiment file containing your pressure-temperature data. make sure that your graph displays temperature on the horizontal axis. if the relationship between pressure and temperature appears to be linear, fit a line to your data. if not, take the necessary steps to obtain a linear relationship. 2. is it correct to state that the pressure is proportional to the celsius temperature; i.e., does a doubling of the temperature produce a doubling of the pressure? if not, then manipulate your graph (logger pro) or use your equation to determine the celsius temperature at which the pressure of a gas should drop to zero. your instructor may guide you in this process. compare your experimental value to the accepted value for this temperature. 3. write a statement relating pressure to the absolute temperature of a gas.

Answers

The absolute temperature is determined by the Kelvin scale, which is the sum of the Celsius temperature and 273.15.

What is a temperature scale?

A temperature scale is a system used to measure and quantify the degree of hotness or coldness of an object or substance. It defines a set of numerical values that correspond to specific temperatures, which can be used to compare temperatures and measure changes in temperature over time.

To open the experiment file containing your pressure-temperature data, first launch the Logger Pro software. From there, you can access your file and adjust the graph's axes accordingly. If the data appears to follow a linear relationship, then fit a line to the data by clicking on the Linear Fit option from the Analyze menu. If the data does not appear to follow a linear relationship, take the necessary steps to adjust the graph and obtain a linear relationship.



It is not correct to state that the pressure is proportional to the Celsius temperature. Pressure increases as temperature increases, but it is not a linear relationship. To find the temperature at which the pressure of a gas should drop to zero, you can either manipulate the graph or use the equation to determine the Celsius temperature. Once you have obtained the temperature, compare it to the accepted value for this temperature.



The pressure of a gas is proportional to the absolute temperature of a gas. The absolute temperature is determined by the Kelvin scale, which is the sum of the Celsius temperature and 273.15.


To learn more about the temperature scale follow

https://brainly.com/question/14035602

#SPJ11

What happens to the conductive properties of wood when it gets very hot?
A. It will change from being a good insulator to becoming a good conductor.
B. It will continue to remain a good conductor.
C. It will continue to remain a good insulator.
D. It will change from being a good conductor to becoming a good insulator.

Answers

Wood will still be an effective insulator. when the temperature of the wood reaches an extreme level.

Compared to materials like metals, marble, glass, and concrete, wood has a low thermal conductivity (high capacity to absorb heat). The axial direction of thermal conductivity is highest, and it rises with density and moisture content, making light, dry woods better insulators.

Insulators are substances that hinder the easy passage of electricity. Plastic, wood, and rubber are among the most insulating nonmetal materials.

Typically, wood has a perpendicular to the grain heat conductivity of between 0.1 and 0.2 W/mK.

It begins to pyrolyze when the temperature rises. Either the materials' internal structure retains the decomposition products, or they release them as gases. When gaseous substances interact with oxygen and each other, a lot of heat is produced. This additional heat promotes pyrolysis and combustion reactions.

Learn more about Insulator here:

https://brainly.com/question/2619275

#SPJ4

the three bins represent three important properties of stars. What are the items that we must measure in orrder to determine each property into the three bins.
Luminosity ________
Surface Temperature________ Mass________

Answers

To determine each property in the three bins, certain items must be measured. The luminosity, surface temperature, and mass are the three important properties of the stars represented by three bins.

The measurement for each property is as follows:

For luminosity: To measure luminosity, we must measure the total amount of energy a star emits in all wavelengths.

For surface temperature: Surface temperature is determined by analyzing the spectrum of light emitted by the star.

The spectrum shows a rainbow of colors, and some colors will be more intense than others. These colors can be used to estimate the temperature of the star's surface.

For mass: Mass is calculated using observations of how the star interacts with its surroundings. Astronomers observe the gravitational effect that a star has on other objects around it. The mass of a star can be estimated using this method.

Stars are gigantic balls of burning gas that light up the sky and heat up planets around them. The sun is a star, for example.

Some stars are smaller and some are larger, but all of them share the same basic structure. The enormous nuclear furnace at the center of every star produces heat and light through fusion.

Stars are made up of mostly hydrogen and helium, but they contain small amounts of other elements. They are classified into three categories based on their luminosity, surface temperature, and mass.

To learn more about stars:https://brainly.com/question/13018254

#SPJ11

Select the correct location on the image.
The image shows the visible light spectrum received from a star. Which three parts of the spectrum show the presence of elements in the star’s atmosphere?

Answers

The visible light spectrum is the range of wavelengths the human eye can detect, ranging from 380 to 700 nanometers.

What are visible light examples?

People think of the sun, light bulbs, candles, and flames when they think of light, but visible light originates from many sources and in many hues. Other visible light sources include television and computer displays, glow sticks, and pyrotechnics.

This is why this area of the electromagnetic spectrum is known as the visible spectrum or colour spectrum. It primarily comprises of seven colours: violet, blue, green, yellow, orange, and red.

Learn more about visible light spectrum

brainly.com/question/18704022

#SPJ1

Answer:

It is the three spots where there are lines. Between 400 and 500(the two lines), between 600 and 700(the two lines), and the one line between 700 and 800.

write an expression for the magnitude of the force, f, exerted on the firefighter by the pole. answer in terms of the variables from the problem statement as well as g for the acceleration due to gravity.

Answers

The expression for the magnitude of the force exerted on the firefighter by the pole can be expressed as  F = mg + ma.  

Where m is the mass of the firefighter,

g is the acceleration due to gravity, and

a is the acceleration of the pole

In order to find an expression for the magnitude of the force, F, exerted on the firefighter by the pole, we need to consider the forces acting on the firefighter.

According to Newton's second law of motion, the force acting on an object is equal to its mass multiplied by its acceleration. In this case, the forces acting on the firefighter are the gravitational force, which is pulling the firefighter downwards with a force of mg, and the force exerted on the firefighter by the pole, which is pushing the firefighter upwards with a force of ma. Therefore, the total force acting on the firefighter is given by the sum of these two forces, which is: F = mg + ma

Thus, this expression gives us the magnitude of the force exerted on the firefighter by the pole. Here, m is the mass of the firefighter, g is the acceleration due to gravity, and a is the acceleration of the pole. if the pole is not accelerating (i.e., if a = 0), then the expression reduces to F = mg, which is the gravitational force acting on the firefighter.

To know more about Magnitude please visit :

https://brainly.com/question/30337362

#SPJ11

Why is this wrong? Can anybody please help me thanks!

Answers

Answer:

[tex]\boxed{5427N}[/tex]

Explanation:

We use the well-known equation:

[tex]F=m\cdot a[/tex]

where:

[tex]F=[/tex] Force (Newton)[tex]m=[/tex] mass [tex](kg)[/tex][tex]a=[/tex] acceleration (m/s^2)

so, we can rewrite the equation like this:

[tex]F= (810kg)(6.7m/s^2)\\F=5427N[/tex]

So, taking into account the statement as seen in the image, your answer must be correct.

[tex]\text{-B$\mathfrak{randon}$VN}[/tex]

When using compass orientation, migrating animals make use of _____.a. memories from previous trips with parentsb. familiar landmarks and olfactory cuesc. the north and south polesd. the sun, stars, and Earth's magnetic field

Answers

When using compass orientation, migrating animals make use of the sun, stars, and Earth's magnetic field to navigate. So, option d is correct option.

Compass orientation in migrating animals is the process of using the sun, stars, and Earth's magnetic field to navigate. Migrating animals use a variety of techniques to navigate, depending on their species and environment.

Some animals use the position of the sun, stars, and Earth's magnetic field as their primary means of orientation when migrating. This is known as compass orientation.

Compass orientation is a technique that relies on environmental cues, such as the position of the sun and stars, to determine direction. Some animals can use the Earth's magnetic field to navigate as well. This is known as magnetic orientation.

Magnetic orientation is used by some species of birds and fish, as well as certain insects and reptiles. Other animals use landmarks and olfactory cues to navigate.

These animals rely on visual or chemical markers in the environment to orient themselves. This technique is known as piloting. Piloting is used by animals such as rodents, bats, and some species of birds. Animals that use piloting must be able to remember and recognize the landmarks they use as cues to navigate.

Finally, some animals use memories from previous trips with parents to navigate. This technique is known as true navigation. True navigation requires animals to have a highly developed sense of spatial awareness and memory. True navigation is used by animals such as sea turtles and some species of birds.

All of these techniques require different cognitive abilities and sensory mechanisms, but they allow animals to navigate over long distances to reach their desired destinations.

for similar question on magnetic field to navigate.

https://brainly.com/question/22986969

#SPJ11

Milk with a density of 970 kg/m ∧ 3 is transported on a level road in a 9−m long, 3−m diameter cylindrical tanker. The tanker is completely filled with milk, i.e., no air space in the tank. If the truck is accelerating from a stop signal at 7.0 m/s ∧ 2 to the left, determine the pressure difference between the maximum and minimum pressures in the tank. Depict on the figure the location of the minimum and maximum pressures in the tank.

Answers

ΔP = (970 kg/m^3)(7.0 m/s^2)(4.26 m) = 29,852 Pascal. Therefore, the pressure difference between the maximum and minimum pressures in the tank is 29,852 Pa. The minimum pressure occurs at the bottom of the tank, while the maximum pressure occurs at the top of the tank.

The pressure difference between the maximum and minimum pressures in the tank can be calculated using the equation for pressure:

P = ρgh

where P is the pressure, ρ is the density of the milk, g is the acceleration due to gravity, and h is the height of the liquid column. Since the tanker is cylindrical and completely filled with milk, the height of the liquid column can be determined using the formula for the volume of a cylinder:

V = πr^2h

where V is the volume of the milk, r is the radius of the tanker (which is half of the diameter), and h is the height of the milk column. Solving for h, we get:

h = V / (πr^2)

The volume of the milk can be determined using the formula for the volume of a cylinder:

V = πr^2h

where r is the radius of the tanker (which is half of the diameter), and h is the length of the tanker. Substituting the given values, we get:

V = π(3/2)^2(9) = 31.8 m^3

The height of the liquid column is:

h = V / (πr^2) = 31.8 / (π(3/2)^2) = 4.26 m

The pressure difference between the maximum and minimum pressures in the tank can be calculated using the formula:

ΔP = ρgh

where ΔP is the pressure difference, ρ is the density of the milk, g is the acceleration due to gravity, and h is the height of the liquid column. Substituting the given values, we get:

ΔP = (970 kg/m^3)(7.0 m/s^2)(4.26 m) = 29,852 Pa

Therefore, the pressure difference between the maximum and minimum pressures in the tank is 29,852 Pa. The minimum pressure occurs at the bottom of the tank, while the maximum pressure occurs at the top of the tank.

For more such questions on Pressure

https://brainly.com/question/20492463

#SPJ11

A motorcyclist starts from rest and reaches a speed of 6m/s after travelling with constant acceleration for 3s. What is his acceleration?

Answers

As given, the motorcyclist starts from rest and reaches a speed of 6 m/s

after traveling with uniform acceleration for 3 seconds.

Here, initial velocity u=0

Final velocity v=6 m/s

Time t=3 sec.

Let the acceleration of the motorcycle be a.

On using the equation of motion, v=u+at

6=0+3×a

Or 3a=6

Or a=63

Or a=2 m/s2

→Therefore, the acceleration in a motorcycle is 2 m/s2.←

a compacted sample of hma contains 5.1 percent asphalt by weight of total mix, and the bulk density of the hma specimen is 2455kg/m3. the specific gravity of aggregate and the asphalt binder are 2.735 and 1.022, respectively. determine the vma, vtm, and vfa, neglect-ing absorption. draw sketch and write out full equations used. no sketch and missing full equations written out, minus -5 points. fyi, following solution is not solved completely as above solution requirement.

Answers

The void in mineral aggregate (VMA) is -12.35%, the void in total mix (VTM) is 0.000990 and the voids filled with asphalt (VFA) is -12.35%.

To determine the VMA, VTM, and VFA neglecting absorption, we need to calculate the following:

[tex]VMA = [(Gmb - Gsb) / Gmb] \times 100[/tex]

[tex]VTM = Gmb / ρb[/tex]

[tex]VFA = [(Gmb - Ga) / Gmb] \times 100[/tex]

Where, Gmb = bulk specific gravity of the compacted specimen of HMA.

Gsb = bulk specific gravity of the aggregate in the HMA specimen.

ρb = bulk density of the HMA specimen

Ga = apparent specific gravity of the aggregate in the HMA specimen.

Substitute the given values we get:

[tex]Gmb = 2.435, Gsb = 2.735, \rho b = 2455\  kg/m^3[/tex],

[tex]Ga = (Gmb \times Gsa) / (5.1 + 0.049 (Gmb - 2.435)) = (2.435 \times 2.735) / (5.1 + 0.049 (2.435 - 2.435)) = 2.449[/tex]

By substituting these values in the above formula, we get:

[tex]VMA = [(2.435 - 2.735) / 2.435] \times 100 = -12.35[/tex]%

[tex]VTM = 2.435 / 2455 = 0.000990[/tex]

[tex]VFA = [(2.435 - 2.735) / 2.435] \times 100 = -12.35[/tex]%

Hence, VMA = -12.35%, VTM = 0.000990, VFA = -12.35%.

The minus sign indicates that the voids are insufficient. Therefore, the mix is unstable.

Learn more about specific gravity:

https://brainly.com/question/20422535

#SPJ11

in theory, a single earthquake should have only one magnitude. true or false?

Answers

True. Earthquakes should have only one magnitude, but in practice, different measurement methods and aftershocks can result in some level of uncertainty and multiple values.

The magnitude of an earthquake is a measure of the amount of energy released during a seismic event. Theoretically, a single earthquake should only have one magnitude, which is determined by analyzing the amplitude of the seismic waves recorded on seismographs. However, in practice, different methods of measurement or different seismic stations can yield slightly different magnitude values, resulting in some level of uncertainty in the reported magnitude. Furthermore, earthquakes can cause aftershocks, which are smaller seismic events that occur after the main earthquake. These aftershocks can have their own magnitudes, which are typically smaller than the main earthquake but can still cause damage and contribute to the overall seismic activity in the region.

learn more about aftershocks here:

https://brainly.com/question/6843834

#SPJ4

an object starts from rest at when the object moves in the x direction with positive velocity after the instantaneous velocity and average velocity are related by (a) (b) (c) (d) can be larger than, smaller than, or equal to

Answers

When an object starts from rest, and it moves in the x direction with a positive velocity, the instantaneous velocity and average velocity are related by the inequality d) "can be larger than, smaller than, or equal to."

The rate at which an object moves in a given direction is known as velocity. It is a vector quantity that has a magnitude and a direction. For example, if an object moves 10 meters to the north in 5 seconds, the velocity is 2 m/s northward.Average velocity and instantaneous velocityInstantaneous velocity is the velocity of an object at a particular instant or point in time. In other words, it's the speed of an object at a specific moment. The average velocity is the total displacement divided by the total time taken for the motion. In other words, it is the total distance covered in a given direction over a specific time period.

The instantaneous velocity and average velocity are related by the inequality that can be larger than, smaller than, or equal to. The instantaneous velocity represents the velocity at a particular moment or point in time, while the average velocity represents the average velocity over a specified time period. The instantaneous velocity and average velocity can be different because the instantaneous velocity is the velocity at a specific moment, whereas the average velocity is the average of all the velocities over a given period of time. Therefore, the instantaneous velocity and average velocity are related by the inequality d) "can be larger than, smaller than, or equal to."

More on velocity: https://brainly.com/question/15721950

#SPJ11

Assume the motions and currents mentioned are along the x axis and fields are in the y direction.
(a) Does an electric field exert a force on a stationary charged object?
YesNo
(b) Does a magnetic field do so?
YesNo
(c) Does an electric field exert a force on a moving charged object?
YesNo
(d) Does a magnetic field do so?
YesNo
(e) Does an electric field exert a force on a straight current-carrying wire?
YesNo
(f) Does a magnetic field do so?
YesNo
(g) Does an electric field exert a force on a beam of moving electrons?
YesNo
(h) Does a magnetic field do so?
YesNo

Answers

(a) Yes, an electric field can exert a force on a stationary charged object. A stationary charged object will experience a force in the direction of the electric field due to the Coulombic interaction between the charges.

(b) No, a magnetic field does not exert a force on a stationary charged object. A stationary charged object does not experience a force due to a magnetic field unless it is moving.

(c) Yes, an electric field can exert a force on a moving charged object. A moving charged object will experience a force perpendicular to its velocity and the electric field direction, known as the Lorentz force.

(d) Yes, a magnetic field can exert a force on a moving charged object. A moving charged object in a magnetic field will experience a force perpendicular to both its velocity and the magnetic field direction, also known as the Lorentz force.

(e) Yes, an electric field can exert a force on a straight current-carrying wire. The electric field exerts a force on the charges in the wire, causing them to move, which results in a net force on the wire.

(f) Yes, a magnetic field can exert a force on a straight current-carrying wire. The magnetic field exerts a force on the moving charges in the wire, resulting in a net force on the wire.

(g) Yes, an electric field can exert a force on a beam of moving electrons. The electric field exerts a force on the electrons, causing them to accelerate or decelerate depending on the direction of the field.

(h) Yes, a magnetic field can exert a force on a beam of moving electrons. The magnetic field exerts a force on the moving electrons, causing them to experience a deflecting force perpendicular to their velocity and the magnetic field direction.

To learn more about electric field refer to:

brainly.com/question/15800304

#SPJ4

a waterbed heater uses 450 w of power. it is on 35 % of the time, off 65 % . part a what is the annual cost of electricity at a billing rate of $0.13 per kwhr ? express your answer using two significant figures.

Answers

The annual cost of electricity at a billing rate of $0.13 per kWhr for a waterbed heater that uses 450 W of power is $36.51.

What is the usage of the waterbed heater in a day?

For the calculation of the energy consumed, one must know the energy consumed by the heater per day. The energy consumed in one day can be calculated by multiplying the power consumed by the hours the heater is used. The power consumed by the heater is 450 W.

The heater is used 35% of the time and is off 65% of the time. The percentage of time the heater is used is calculated using the formula:

Percentage of time the heater is used = (Time heater is on/Total time) × 100

Percentage of time the heater is used = (35/100) × 100

Percentage of time the heater is used = 35%

The percentage of time the heater is off is calculated using the formula:

Percentage of time the heater is off = (Time heater is off/Total time) × 100

Percentage of time the heater is off = (65/100) × 100

Percentage of time the heater is off = 65%

Thus, the heater is used for 8.4 hours per day (i.e., 24 hours × 35%) and is off for 15.6 hours per day (i.e., 24 hours × 65%).

The energy consumed per day can be calculated by multiplying the power consumed by the time the heater is on. Energy consumed per day = Power consumed × Time heater is on

Energy consumed per day = 450 W × 8.4 hours

Energy consumed per day = 3780 Wh

Energy consumed per day = 3.78 kWh

The annual cost of electricity can be calculated by multiplying the energy consumed per year by the cost of electricity per kWh.

Annual cost of electricity = Energy consumed per year × Cost of electricity per kWh

Annual cost of electricity = 3.78 kWh × $0.13/kWh

Annual cost of electricity = $0.4914/day

Annual cost of electricity = $179.31/year

Hence, the annual cost of electricity at a billing rate of $0.13 per kWhr for a waterbed heater that uses 450 W of power is $36.51.

Learn more about Power here:

https://brainly.com/question/27442707

#SPJ11

C. Demonstrate the effect of simple machines on work.
Simple machines make work.
but not
Explain which simple machine(s) you can use in each situation and how
it will help make work easier:
1. Putting a motorcycle into the back of a trailer.
2. Lifting a flag to the top of the flagpole.
3. Moving dirt from the front yard to the backyard.
4. Attaching two boards together.
5. Splitting a log in half.
6. Cutting paper.
7. Lifting a car to change the tire.
8. Moving from the bottom floor of the house to the top floor.
9. Opening a can of peaches.
10. Cutting a piece of cheese.

Answers

Putting a motorcycle into the back of a trailer: A ramp is a simple machine that can be used to make this task easier. By placing a ramp at the back of the trailer, the motorcycle can be rolled up the ramp instead of being lifted manually.

The Explanation of the simple machines to be used

Lifting a flag to the top of the flagpole: A pulley is a simple machine that can be used to make this task easier. By attaching a pulley to the top of the flagpole and another pulley at ground level, a rope can be run through the pulleys, allowing the flag to be lifted with less force.

Moving dirt from the front yard to the backyard: A wheelbarrow is a simple machine that can be used to make this task easier. By loading dirt into the wheelbarrow and pushing it, the person doing the work can move more dirt with less effort.

Attaching two boards together: A screw is a simple machine that can be used to make this task easier. By using a screwdriver to turn a screw into one board and then into the other, the boards can be securely attached with less effort.

Splitting a log in half: A wedge is a simple machine that can be used to make this task easier. By positioning a wedge at the center of the log and hitting it with a mallet or hammer, the log can be split into two pieces with less force.

Cutting paper: Scissors are a simple machine that can be used to make this task easier. By using the scissors' blades to apply force to the paper, the person cutting can apply less force than if they were tearing the paper by hand.

Lifting a car to change the tire: A jack is a simple machine that can be used to make this task easier. By placing the jack under the car and using a handle to lift the car off the ground, the person changing the tire can exert less force than if they were trying to lift the car manually.

Moving from the bottom floor of the house to the top floor: Stairs are a simple machine that can be used to make this task easier. By using the inclined plane formed by the stairs, the person climbing the stairs can expend less effort than if they were climbing a straight ladder.

Opening a can of peaches: A can opener is a simple machine that can be used to make this task easier. By using the can opener's sharp blade to cut through the can lid, the person opening the can can apply less force than if they were trying to pry the lid off by hand.

Cutting a piece of cheese: A knife is a simple machine that can be used to make this task easier. By using the knife's sharp edge to cut through the cheese, the person cutting can apply less force than if they were trying to tear the cheese by hand.

Read more about simple machines here:

https://brainly.com/question/28750066

#SPJ1

A simple machine is an expression used to basically describe a tool that helps make work easier.

What are examples of simple machines?

A simple machine is a mechanical device that changes the direction or magnitude of a force such that things can be lifted with less effort.

For example, a lever system like a crane could be used to put a motorcycle into the back of a trailer; or to lift a flag to the top of the flagpole. While, an inclined plane, such as a ramp, can be used to move dirt from the front yard to the backyard. And a screw can be used to attach two boards together.

A wedge, on the other hand, can be used to split a log in half.  A pair of scissors, which is a type of lever, can be used for cutting paper. Meanwhile, a hydraulic jack could be used for lifting a car to change the tire.

A can opener, which is also a type of wedge can be used for opening a can of peaches. And then, lastly, a knife, which is a type of wedge, is ideal for cutting a piece of cheese.

You can learn more about simple machines here https://brainly.com/question/14696504

#SPJ1

In the context of research evidence from the study conducted by Williams and McCririe, which of the following operates when a person picks up information critical to catching an object
both central and peripheral vision

Answers

In the context of research evidence from the study conducted by Williams and McCririe, both central and peripheral vision operate when a person picks up information critical to catching an object.

What is vision?

Vision is the sense that allows us to recognize and understand the physical world around us. Our brains then receive this information and convert it into the pictures that we see with our eyes.

Vision is the term used to describe the ability to see things with our eyes, such as color, form, and movement.

In the context of research evidence from the study conducted by Williams and McCririe, both central and peripheral vision operate when a person picks up information critical to catching an object.

Their research found that peripheral vision was essential to athletes performing in certain sports such as cricket, soccer, and baseball.

Peripheral vision, as well as central vision, are critical components of efficient eye tracking and hand-eye coordination.

Learn more about vision here:

https://brainly.com/question/4269555

#SPJ11

Somewhat paradoxically, new parents report _____ marital satisfaction and _____ love for each other. less; more.

Answers

Somewhat paradoxically, new parents report less marital satisfaction and more love for each other. This statement may seem contradictory at first glance, but it is entirely reasonable when we examine it more closely.

Marriage satisfaction refers to the degree of satisfaction that a person derives from being in a relationship with their partner. It is essential to comprehend that the satisfaction levels may fluctuate over time, and external factors such as parenthood may influence the levels.

Parenthood, on the other hand, is characterized by the arrival of a new member into the family. As a result, new parents are required to balance and divide their time between their relationship and their child. This task is challenging and can take a significant toll on the couple's relationship, resulting in reduced marital satisfaction levels.On the other hand, the arrival of a new baby also brings an immense amount of joy and love into the couple's life.

The couple's love and affection for each other may intensify due to the shared experience of bringing a new life into the world. As a result, new parents may report more love for each other despite a decrease in marital satisfaction levels.In conclusion, new parents may report less marital satisfaction but more love for each other due to the challenges and demands of parenthood. Despite the challenges, parenthood may also bring an immense amount of love and joy into the couple's life.

for such more questions on paradoxically

https://brainly.com/question/31218828

#SPJ11

A falling object experiment is performed to determine the acceleration due to gravity on an unknown planet (not the Earth) from photographic data of the falling object.
At time = 0 seconds, the object's displacement is 0 m.
At time = 0.4 seconds, the object's displacement is 1.5 m.
From the above information, calculate the value of the acceleration due to gravity on the unknown planet.

Answers

18.75 m/s² is the acceleration brought on by gravity on the unidentified planet.

What type of acceleration does an item have when it falls naturally under the influence of gravity?

9.8 m/s2 is the acceleration caused by gravity at or close to the surface of the Earth. The force of gravity causes items to fall towards the ground.

The acceleration brought on by gravity on the unidentified planet may be calculated using the equation of motion for a falling object:

d = 1/2 * g * t²

where d is the object's displacement, g is the acceleration brought on by gravity, and t is the passing of time.

This equation can be changed in order to account for g:

g = 2 * d / t²

Plugging in the given values:

d = 1.5 m

t = 0.4 s

g = 2 * 1.5 m / (0.4 s)²

g = 18.75 m/s²

To know more about acceleration visit:-

https://brainly.com/question/30660316

#SPJ1

True or False: For a given water velocity (distance traveled per unit time), the greater the cross sectional area of a stream channel, the lower will be the stream flow (discharge: volume of water per unit time).

Answers

For a given water velocity (distance traveled per unit time), the greater the cross-sectional area of a stream channel, the lower will be the stream flow (discharge: volume of water per unit time)" is a false statement.

What is Stream discharge?

Stream discharge is measured by the volume of water flowing per unit of time, which is calculated by multiplying the stream's cross-sectional area (flow width × flow depth) by its water velocity. As a result, the given statement is false.

According to the formula, an increase in the cross-sectional area of the stream will cause a rise in the stream flow (discharge: volume of water per unit time) because it is multiplied by the velocity. So, for a given water velocity, the greater the cross-sectional area of a stream channel, the higher the stream flow (discharge: volume of water per unit time) will be.

Learn more about Stream discharge here:

https://brainly.com/question/8282980

#SPJ11

We can test our stellar ages and models for the birth, evolution, and death of stars by determining if our observations of the metallicity within each component of the galaxy match our predictions. On the basis of how the life cycles of stars affect the composition of interstellar gas with time, rank the expected metallicities of the following components of our galaxy in order from lowest to highest.halo, bulge, thin disk

Answers

The rank order of expected metallicities, from lowest to highest, is Halo, Bulge, and Thin Disk.

The expected metallicities of the components of our galaxy, ranked from lowest to highest, are as follows:

1. Halo: The halo is the oldest component of our galaxy, consisting of old stars and globular clusters. It formed early in the galaxy's history when interstellar gas had low metallicity. Therefore, the halo is expected to have the lowest metallicity among the three components.

2. Bulge: The bulge is the central, densely packed region of the galaxy. It contains a mix of old and intermediate-age stars. The bulge formed through a combination of both primordial gas collapse and subsequent mergers.

3. Thin Disk: The thin disk is the relatively young and dynamically active component of our galaxy. It contains most of the young stars, star-forming regions, and open clusters.

The thin disk formed more recently from gas with a higher metallicity due to previous generations of star formation. As a result, the thin disk is expected to have the highest metallicity among the three components.

Know more about metallicity:

https://brainly.com/question/29404080

#SPj12

suppose that you drop a solid iron ball and a hollow iron ball, both the exact same diameter, from the same height at the same time. aristotle would predict that

Answers

If you drop a solid iron ball and a hollow iron ball of the same diameter from the same height at the same time, Aristotle's prediction would be that the solid iron ball will fall faster than the hollow iron ball.

Aristotle and gravity law

Aristotle, who lived in ancient Greece, believed that heavier objects would fall faster than lighter ones. This was a commonly held belief at the time, but it has since been proven incorrect through scientific experiments.

In reality, when dropped from the same height at the same time, both the solid iron ball and the hollow iron ball of the same diameter would fall at the same rate, neglecting air resistance. This is because the rate at which an object falls is determined by its mass and the force of gravity acting on it, which are the same for both balls.

This was first demonstrated by Galileo Galilei in the late 16th century through his famous experiment involving dropping objects from the Leaning Tower of Pisa. He showed that objects of different masses would fall at the same rate in a vacuum and that air resistance was the primary factor that caused objects to fall at different rates in the real world.

In summary, Aristotle would have predicted that the solid iron ball would fall faster than the hollow iron ball, but this prediction has been shown to be incorrect by scientific experiments.

More on Aristotle can be found here: https://brainly.com/question/5399979

#SPJ1

What is the cause of dispersion of white light as it passes through a prism?

Answers

When white light passes through a prism, it is refracted, or bent, by the prism's surface, because the refractive index of the prism is different for different wavelengths of light.

Because of this variation in the refractive index, the different colors of light that make up white light (red, orange, yellow, green, blue, indigo, and violet) are refracted by different amounts, separating them into a spectrum of colors. This effect is known as dispersion.

The degree of refraction of each color is determined by its wavelength, with shorter wavelengths being bent more than longer wavelengths. This is why the colors are separated, with violet light being refracted the most, followed by blue, green, yellow, orange, and red.

To learn more about dispersion  refer to:

brainly.com/question/30687707

#SPJ4

in one cycle a heat engine absorbs 480 j from a high-temperature reservoir and expels 320 j to a low-temperature reservoir. if the efficiency of this engine is 56% of the efficiency of a carnot engine, what is the ratio of the low temperature to the high temperature in the carnot engine?

Answers

The ratio of the low temperature to high temperature of the Carnot engine is 2.38.

What is the efficiency of Carnot engine?

The efficiency of the Carnot engine can be defined as the ratio of network done per cycle by the engine to the heat energy absorbed by the engine per cycle by the working substance from the source.


Efficiency = 1 - (Tlow/Thigh)


Heat absorbed by engine = 480J

Heat expelled by engine = 320J

Efficiency of the engine = 56% of efficiency of Carnot engine

The ratio of low temperature to high temperature in the Carnot engine.

Let's assume the efficiency of the Carnot engine is 'ηc' = 1 - T₂/T₁

Where, T₂ = Low temperature and T₁ = High temperature

To calculate the efficiency of the engine given, η = (Q1 - Q2)/Q1

η = (480 - 320)/480

η = 160/480

η = 1/3

η = 33.33%

Now, η = 56% × ηc

0.56ηc = 1/3ηc = (1/3)/0.56 = 0.58

As we already know, ηc = 1 - T₂/T₁

T₂/T₁ = 1 - ηc

T₂/T₁ = 1 - 0.58

T₂/T₁ = 0.42

T₁/T₂ = 1/0.42

T₁/T₂ = 2.38

Therefore, the ratio of low temperature to high temperature in the given Carnot engine with an efficiency of 56% will be about 2.38.

Learn more about Carnot engine here:

https://brainly.com/question/14680478


#SPJ11

The half life of a radioactive substance is 5 hours. If 5g of the substance is left after 20 hours, determine the original mass of the substance​

Answers

Answer:

The original mass of the substance was 10g.

Explanation:

The half-life of a radioactive substance is the amount of time it takes for half of the substance to decay. In this case, the half-life is 5 hours.

We can use the half-life formula to find the original mass of the substance:

N = N0 * (1/2)^(t/T)

where:

---N0 is the initial mass of the substance

---N is the remaining mass of the substance after time t

---T is the half-life of the substance

We know that after 20 hours, only half of the substance remains:

N = N0 * (1/2)^(20/5) = 0.5 * N0

If we solve for N0, we get:

N0 = N / 0.5 = 5g / 0.5 = 10g

Therefore, the original mass of the substance was 10g.

a student pulls a 1500 kg suitcase along a flat sidewalk. if the cord on the suitcase breaks when the force is greater than 50n, what is the maximum acceleration that the student can achieve with the suitcase?

Answers

The maximum acceleration that the student can achieve with the 1500 kg suitcase is 50N/1500kg = 0.033 m/s2.

Acceleration is the change in velocity per unit time. Acceleration is a vector quantity that has both magnitude and direction. Acceleration is divided into deceleration acceleration and acceleration acceleration. Acceleration decreases meaning the direction of acceleration is opposite to the direction of velocity.


To calculate the maximum acceleration, we can use the following equation:
Force = Mass x Acceleration. Therefore, 50N = 1500kg x Acceleration

Solving for Acceleration, we get 50N/1500kg = 0.033 m/s2.

Learn more about acceleration : brainly.com/question/20595261

#SPJ11

an unsaturated parcel of air has a temperature of -5c at an elevation of 3000 meters. the parcel, remaining unsaturated, sinks all the way to the surface. what is the temperature of the parcel when it reaches the surface?

Answers

The temperature of the unsaturated parcel of air when it reaches the surface will be higher than -5°C. As the parcel descends, it will expand, which increases the air's internal energy and causes the temperature to rise. The amount of temperature rise depends on the rate of descent, which is determined by the parcel's buoyancy and surrounding air density.


In general, the temperature increase of an unsaturated parcel of air is approximately 0.65°C per 100 m of descent. For a parcel descending from 3000 m elevation to the surface, the temperature increase will be approximately 19.5°C (0.65°C/100 m * 3000 m). Therefore, the temperature of the unsaturated parcel of air when it reaches the surface will be approximately 14.5°C (19.5°C + -5°C).


The temperature of the unsaturated parcel of air when it reaches the surface after descending from an elevation of 3000 meters is +11°C.

What is the unsaturated parcel of air?

In meteorology, an unsaturated parcel of air refers to a parcel of air that has a relative humidity that is less than 100 percent. If the temperature of the unsaturated parcel of air is lower than the dew point temperature, the relative humidity of the parcel of air is decreased as the temperature of the air rises. In this case, since the parcel is unsaturated, we can make the assumption that the lapse rate is dry and equal to 10°C/km or 1°C/100 meters. Calculating the temperature of the unsaturated parcel when it reaches the surface can use the dry adiabatic lapse rate to determine the temperature of the unsaturated parcel of air when it reaches the surface. Since the lapse rate is dry and the parcel is unsaturated, the dry adiabatic lapse rate is used in the calculation. The formula used in this calculation is: T = T_0 + (dry adiabatic lapse rate × altitude)where T = temperature, T_0 = initial temperature, and altitude = elevation temperature of the unsaturated parcel of air at an elevation of 3000 meters is -5°C. Using the dry adiabatic lapse rate of 1°C/100 meters, we get: Altitude = 3000 meters Dry adiabatic lapse rate = 1°C/100 metersInitial temperature (T_0) = -5°CT = -5°C + (1°C/100 meters × 3000 meters)T = -5°C + 30°CT = 25°CAfter descending to the surface, the temperature of the unsaturated parcel of air is +11°C, according to the above calculation.

For more information follow the link: https://brainly.com/question/11464844

#SPJ11

Other Questions
Which contributed most to imperialistic actions taken by the United States in the late 19th and early 20th century? growth of industryconstruction of railroadstreaties with other countriesdevelopment of national pride the speed of an airplane is 275 mi/h relative to the air. the wind is blowing due north with a speed of 35 mi/h. in what direction should the airplane head in order to arrive at a point due west of its location? (round your answer to two decimal places.) The country of ____ is a volcanic plateau built of basaltic lava erupted from a hot spot underlying the Mid-Atlantic Ridge in the North Atlantic Ocean. which statement correctly analyzes how the passages work together to develop a central idea?analyzing the development of a central idea True or False? The Labor Market is the institution by which workers and employers come together to engage in the production of output. if a stimulus was applied in the middle of a nerve roughly halfway between the cell body and the axon terminal, would the resulting action potentials travel only from the stimulus point to the axon terminal? You are the main speaker for your in an inter-school debate competition on the mention The home has more influence on the child than the school" Write a debate speech. When solving the equation 3(x-2)=-12, what is a possible first step? *1)Distributing the 3 into each term of the parenthesis.2)She could either divide by 3 or distribute 3 into the parenthesis3)Adding 2 to each side of the equation4) Subtracting 2 on each side of the equation5) Dividing each side of the equation by 36)none of the answer choices tell what the first step could be. The interjection eh is a _______ used primarily by Canadians.A) juggernautB) kowtowC) shibbolethD) nabob standards promulgated by the fasb are most likely to be adhered to by which of the following governmental units? 5 paragraph about systemic racism in education (High school +) 4 facts about it and real life cases with an example of my topic (MLA CITATION) the export license application and information network (elain) is an electronic service that enables exporters to Most exposures and outcomes used in correlational studies are in the form of:A. Individual dataB. Aggregate dataC. Average dataD. Relative data how many different player nationalities were included in the confirmed squads by the uefa champions league teams which qualified for the knockout stage of the uefa champions league on february 2nd, 2023 ? a very long straight wire carries current 32 a. in the middle of the wire a right-angle bend is made. the bend forms an arc of a circle of radius 14 cm, as show. determine the magnetic field at the center of the arc. How does this legislation address the need to equip these new soldiers? Work out x. Area=194Please help due in 2 hourss T/F a buffer overflow attack abuses a program's lack of length limitations on the data it receives before storing the input in memory, which can lead to arbitrary code execution. Which of the following is concerned with monitoring estimates of present performance and predictions of future performance?Select one:a. Content validityb. Predictive validityc. Concurrent validityd. Construct validity Which of the following best describes the possible outcome of creating a tafree banking zone in a country?OA. International investors will avoid that zoneOB. International investors will be attracted to that zoneOC. Government regulations may be lifted in other countriesOD. The local economy will suffer as tax income decreases