Magnetic resonance imaging needs a magnetic field strength of 1.5 T. The solenoid is 1.8 m long and 75 cm in diameter. It is tightly wound with a single layer of 1.50-mm-diameter superconducting wire.
What current is needed?

Answers

Answer 1

Answer:

The current needed is 1790.26 A

Explanation:

Given;

magnitude of magnetic field, B = 1.5 T

length of the solenoid, L = 1.8 m

diameter of the solenoid, d = 75 cm = 0.75 m

The magnetic field is given by;

[tex]B = \frac{\mu_o NI }{L}[/tex]

Where;

μ₀ is permeability of free space = 4π x 10⁻⁷ m/A

I is current in the solenoid

N is the number of turns, calculated as;

[tex]N = \frac{Length \ of\ solenoid}{diameter \ of \ wire} \\\\N = \frac{1.8}{1.5*10^{-3}} =1200 \ turns[/tex]

The current needed is calculated as;

[tex]I = \frac{BL}{\mu_o N} \\\\I = \frac{1.5 *1.8}{4\pi *10^{-7} *1200} \\\\I = 1790.26 \ A[/tex]

Therefore, the current needed is 1790.26 A.

Answer 2

Answer:

I = 1790.5 A

Explanation:

The magnetic field due to a solenoid is given by the following formula:

B = μ₀NI/L

where,

B = Magnetic Field Required = 1.5 T

μ₀ = 4π x 10⁻⁷ T/A.m

L = length of Solenoid = 1.8 m

I = Current needed = ?

N = No. of turns = L/diameter of wire = 1.8 m/1.5 x 10⁻³ m = 1200

Therefore,

1.5 T = (4π x 10⁻⁷ T/A.m)(1200)(I)/1.8 m

I = (1.5 T)(1.8 m)/(1200)(4π x 10⁻⁷ T/A.m)

I = 1790.5 A


Related Questions

"A light beam incident on a diffraction grating consists of waves with two different wavelengths. The separation of the two first order lines is great if"

Answers

Answer:

A light beam incident on a diffraction grating consists of waves with two different wavelengths. The separation of the two first order lines is great if

the dispersion is great

A front wheel drive car starts from rest and accelerates to the right. Knowing that the tires do not slip on the road, what is the direction of the friction force the road applies to the front tires

Answers

Answer:

static friction acting opposite to the direction of travel

Explanation:

Because the Frictional force of the front wheels act to oppose the spinning, so, For the front wheels to roll without slipping, the friction must be static friction pointing in the direction of travel of the car.

Explanation:

The distance from the Sun to Earth is approximately 149,600,000 km. The distance from the Sun to Venus is approximately 108,200,000 km. The elongation angle αα is the angle formed between the line of sight from Earth to the Sun and the line of sight from Earth to Venus. Suppose that the elongation angle for Venus is 10∘.10 ∘. Use this information to find the possible distances between Earth and Venus.

Answers

Answer:

335206922km

Explanation:

Pls see attached file

In a physics lab, Asha is given a 11.5 kg uniform rectangular plate with edge lengths 62.9 cm by 46.9 cm . Her lab instructor requires her to rotate the plate about an axis perpendicular to its plane and passing through one of its corners, and then prepare a report on the project. For her report, Asha needs the plate's moment of inertia ???? with respect to given rotation axis. Calculate ???? .

Answers

Answer:

6.9kgm²

Explanation:

For an axis through the center of the rectangle, I = m[(w²+L²)/12

Using the parallel axis theorem, the added value of I = mR² = m[(w²/4 + L²/4]

Adding the 2 expressions,

I = (m/3)*(w²+L²)

I =6.95 kg∙m²

Some stove tops are smooth ceramic for easy cleaning. If the ceramic is 0.630 cm thick and heat conduction occurs through an area of 1.45 ✕ 10−2 m2 at a rate of 500 J/s, what is the temperature difference across it (in °C)? Ceramic has the same thermal conductivity as glass and concrete brick.

Answers

Answer:

The temperature difference [tex]\Delta T = 258.6 \ ^ o\ C[/tex]

Explanation:

From the question we are told that

   The  thickness is [tex]\Delta x = 0.630 cm = 0.0063 m[/tex]

    The  area is  [tex]A = 1.45 *10^{-2 } \ m^2[/tex]

     The rate is  [tex]P = 500 J/s[/tex]

       The  thermal conductivity is  [tex]\sigma = 0.84J[\cdot s \cdot m \cdot ^oC ][/tex]

Generally the rate heat conduction mathematically represented as

       [tex]P = \sigma * A * \frac{\Delta T}{\Delta x }[/tex]

=>    [tex]\Delta T = \frac{P * \Delta x }{\sigma * A }[/tex]

=>     [tex]\Delta T = \frac{ 500 * 0.00630 }{ 0.84 * 1.45 *10^{-2} }[/tex]

=>    [tex]\Delta T = 258.6 \ ^ o\ C[/tex]

Which of these cannot be a resistor in a series or parallel circuit?
A)switch
B) battery
C) light bulb
D) all of these are resistors

Answers

Answer:

it is going to D. all of these are resistors

Copper Pot A copper pot with a mass of 2 kg is sitting at room temperature (20°C). If 200 g of boiling water (100°C) are put in the pot, after a few minutes the water and the pot come to the same temperature. What temperature is this in °C?

Answers

Answer:

The final temperature is 61.65 °C

Explanation:

mass of copper pot [tex]m_{c}[/tex] = 2 kg

temperature of copper pot [tex]T_{c}[/tex] = 20 °C  (the pot will be in thermal equilibrium with the room)

specific heat capacity of copper [tex]C_{c}[/tex]= 385 J/kg-°C

The heat content of the copper pot = [tex]m_{c}[/tex][tex]C_{c}[/tex][tex]T_{c}[/tex] = 2 x 385 x 20 = 15400 J

mass of boiling water [tex]m_{w}[/tex] = 200 g = 0.2 kg

temperature of boiling water [tex]T_{w}[/tex] = 100 °C

specific heat capacity of water [tex]C_{w}[/tex] = 4182 J/kg-°C

The heat content of the water = [tex]m_{w}[/tex][tex]C_{w}[/tex][tex]T_{w}[/tex] = 0.2 x 4182 x 100 = 83640 J

The total heat content of the water and copper mix [tex]H_{T}[/tex] = 15400 + 83640 = 99040 J

This same heat is evenly distributed between the water and copper mass to achieve thermal equilibrium, therefore we use the equation

[tex]H_{T}[/tex] =   [tex]m_{c}[/tex][tex]C_{c}[/tex][tex]T_{f}[/tex] + [tex]m_{w}[/tex][tex]C_{w}[/tex]

where [tex]T_{f}[/tex] is the final temperature of the water and the copper

substituting values, we have

99040 = (2 x 385 x [tex]T_{f}[/tex]) + (0.2 x 4182 x

99040 = 770[tex]T_{f}[/tex] + 836.4

99040 = 1606.4[tex]T_{f}[/tex]

[tex]T_{f}[/tex] = 99040/1606.4 = 61.65 °C

A polarized laser beam of intensity 285 W/m2 shines on an ideal polarizer. The angle between the polarization direction of the laser beam and the polarizing axis of the polarizer is 16.0 ∘. What is the intensity of the light that emerges from the polarizer?

Answers

Answer:

The intensity is  [tex]I_1 = 263.35 \ W/m^2[/tex]

Explanation:

From the question we are told that

    The intensity of the beam is  [tex]I = 285\ W/m^2[/tex]

    The  angle is [tex]\theta = 16^o[/tex]

The  intensity of the light that emerges from the polarizer is mathematically represented by Malus' law as

        [tex]I_1 = I * cos^2 (\theta )[/tex]

substituting values

        [tex]I_1 = 285 * [cos(16)]^2[/tex]

substituting  values

        [tex]I_1 = 285 * [cos(16)]^2[/tex]

        [tex]I_1 = 263.35 \ W/m^2[/tex]

If this is the only water being used in your house, how fast is the water moving through your house's water supply line, which has a diameter of 0.021 m (about 3/4 of an inch)?

Answers

Answer:

0.273m/s

Explanation:

first find out the meaning of 0.90×10−4m3/s

literally, that is 0.9x6 = 5.4m3/s = 3•5.4m/s or 16.2 m/s

1.5 gal/min = 0.00009464 m³/s, perhaps that is what you mean?

cross-sectional area of pipe is πr² = 0.0105²π = 0.0003464 m²

so you have a a flow of 0.00009464 m³/s flowing through an area of 0.0003464 m²

they divide to 0.00009464 m³/s / 0.0003464 m² = 0.273 m/s

A lamp has the shape of a parabola when viewed from the side. The lamp is centimeters wide and centimeters deep. How far is the light source from the bottom of the lamp if the light source is placed at the focus

Answers

The question is not complete so i have attached it.

Answer:

The light source is 2 cm from the bottom of the lamp

Explanation:

From the attached image, we can see that the parabola opens up with its vertex at the origin.

Now, the standard form of equation for a parabola is:

x² = 4ay

Looking at the parabola in the attachment, the top right edge of the lamp has a coordinate of (12,18)

Thus, we have;

12² = 4a(18)

144 = 72a

a = 144/72

a = 2

Looking at the parabola again, the line of symmetry is at x = 0

Thus, axis of symmetry is at x = 0.

Thus, focus is at (0, 2)

So, if the light source is placed at the focus, the distance of the light source from the bottom of the lamp is 2 cm

The distance of the light source from the bottom of the lamp is 2 cm.

The given parameters;

the top right edge of the lamp has a coordinate of (12,18)

Apply standard parabola equation to determine the distance of the light source from the bottom of the lamp;

[tex]x^2 = 4ay\\\\12^2 = 4a(18)\\\\144 = 72 a\\\\a = \frac{144}{72} \\\\a = 2 \ cm[/tex]

Thus, the distance of the light source from the bottom of the lamp is 2 cm.

"Your question is not complete, it seems to be missing the following information";

the top right edge of the lamp has a coordinate of (12,18)

Learn more here:https://brainly.com/question/14459938

Discuss the phase change condition due to reflection of light from a surface. Summarize equations of interference for thin film.

Answers

Answer:

if this surface has a higher index than in the medium where the light travels, the reflected wave has a phase change of 180º

Explanation:

When a ray of light falls on a surface if this surface has a higher index than in the medium where the light travels, the reflected wave has a phase change of 180º this can be explained by Newton's third law, the light when arriving pushes the atoms of the medium that is more dense, and these atoms respond with a force of equal magnitude, but in the opposite direction.

When the fractional index is lower than that of the medium where the reflacted beam travels, notice a change in phase.

Also, when light penetrates the medium, it modifies its wavelength

              λ = λ₀ / n

We take these two aspects into account, the condition for contributory interference is

            d sin θ = (m + 1/2) λ

for destructive interference we have

            d sin θ = m λ

in general this phenomenon is observed at 90º

           2 d = (m +1/2) λ° / n

          2nd = (m + ½) λ₀

The target variable is the speed of light v in the glass, which you can determine from the index of refraction n of the glass. Which equations will you use to find n and v?

Answers

Answer:

n= speed of light in vacuum/ speed of light in the other medium.

Explanation:

If light is moving from medium 1 into medium 2 where medium 1 is vacuum (approximated to mean air) and we are required to find the velocity of light; then we can confidently write;

n= speed of light in vacuum/ speed of light in the other medium.

Hence;

n= c/v

Where;

n= refractive index of the material

c= speed of light in vacuum

v = speed of light in another medium.

Note that the refractive index is the amount by which a transparent medium decreases the speed of light.

In 8,450 seconds, the number of radioactive nuclei decreases to 1/16 of the number present initially. What is the half-life (in s) of the material

Answers

Answer:

2113 seconds

Explanation:

The general decay equation is given as [tex]N = N_0e^{-\lambda t} \\\\[/tex], then;

[tex]\dfrac{N}{N_0} = e^{-\lambda t} \\[/tex] where;

[tex]N/N_0[/tex] is the fraction of the radioactive substance present = 1/16

[tex]\lambda[/tex] is the decay constant

t is the time taken for decay to occur = 8,450s

Before we can find the half life of the material, we need to get the decay constant first.

Substituting the given values into the formula above, we will have;

[tex]\frac{1}{16} = e^{-\lambda(8450)} \\\\Taking\ ln\ of \both \ sides\\\\ln(\frac{1}{16} ) = ln(e^{-\lambda(8450)}) \\\\\\ln (\frac{1}{16} ) = -8450 \lambda\\\\\lambda = \frac{-2.7726}{-8450}\\ \\\lambda = 0.000328[/tex]

Half life f the material is expressed as [tex]t_{1/2} = \frac{0.693}{\lambda}[/tex]

[tex]t_{1/2} = \frac{0.693}{0.000328}[/tex]

[tex]t_{1/2} = 2,112.8 secs[/tex]

Hence, the half life of the material is approximately 2113 seconds

How does a negative ion differ from an uncharged atom of the same
element?
O A. The ion has a greater number of protons.
B. The ion has fewer protons.
O C. The ion has a greater number of electrons.
O D. The ion has fewer neutrons.​

Answers

Answer:

C if it is a negitive ion it has more electrons because protons determine what element it is

A spark is generated in an automobile spark plug when there is an electric potential of 3000 V across the electrode gap. If 60 W of power is generated in a single spark that delivers a total charge of 3 nC, how long does it take for the spark to travel across the gap?
A. 50 ns
B. 75 ns
C. 125 ns
D. 150 ns
E. 225 ns 5

Answers

Answer:

The correct option is  d

Explanation:

From the question we are told that

     The  electric potential is  [tex]V = 3000 \ V[/tex]

      The  power is  [tex]P = 60 \ W[/tex]

      The  charge delivered is  [tex]q = 3nC = 3.0 *10^{-9} \ C[/tex]

Generally the power generated is mathematically represented as

         [tex]P = I V[/tex]

=>      [tex]I = \frac{P}{V }[/tex]

=>       [tex]I = \frac{60 }{3000 }[/tex]

=>     [tex]I = 0.02 \ A[/tex]

This  current flow is mathematically represented as

           [tex]I = \frac{q -q_o}{\Delta t }[/tex]

Where [tex]q_o[/tex] is the charge delivered at t=0 s which is 0s

     So

             [tex]0.02 = \frac{ (3.0 *10^{-9}) -0 }{t - 0 }[/tex]

               [tex]t = 1.50 *10^{-7 } \ s[/tex]

               [tex]t = 150 *10^{-9 } \ s[/tex]

Specular reflection occurs where the light ray in the glass strikes the reflector. If no light is to enter the water, we require that there be reflection only. Which phenomenon prevents the light from entering the water?

Answers

Answer:

The critical angle phenomenon.

Explanation:

Critical angle in optics is the smallest angle of incidence of a wave, that will give total reflection of the wave. This phenomenon occurs at the boundary of two medium, where light will normally move from one medium to another.

To prevent light from entering the water, the angle of incidence of the light incident on the water must exceed the critical angle.

A string is stretched and fixed at both ends, 200 cm apart. If the density of the string is 0.015 g/cm, and its tension is 600 N, what is the fundamental frequency

Answers

Answer:

f₀ = 158.12 Hertz

Explanation:

The fundamental frequency of the string  f₀ is expressed as f₀ = V/4L where V is the speed experienced by the string.

[tex]V = \sqrt{\frac{T}{\mu} }[/tex] where T is the tension in the string and  [tex]\mu[/tex] is the density of the string

Given T = 600N and [tex]\mu[/tex] = 0.015 g/cm  = 0.0015kg/m

[tex]V = \sqrt{\frac{600}{0.0015} }\\ \\V = \sqrt{400,000}\\ \\V = 632.46m/s[/tex]

The next is to get the length L of the string. Since the string is stretched and fixed at both ends, 200 cm apart, then the length of the string in metres is 2m.

L = 2m

Substituting the derived values into the formula f₀ = V/2L

f₀ = 632.46/2(2)

f₀ = 632.46/4

f₀ = 158.12 Hertz

Hence the fundamental frequency of the string is 158.12 Hertz

A step-down transformer is used for recharging the batteries of portable devices. The turns ratio N2/N1 for a particular transformer used in a CD player is 2:29. When used with 120-V (rms) household service, the transformer draws an rms current of 180 mA.
Find the rms output voltage of the transformer

Answers

Answer:

8.28 V

Explanation:

Using,

N2/N1 = V2/V1.................. Equation 1

Where N2/N1 = Turn ratio of the transformer, V1 = primary/input voltage, V2 = output/secondary voltage

make V2 the subject of the equation

V2 = (N2/N1)V1............ Equation 2

Given: N2/N1 = 2:29 = 2/29, V1 = 120 V

Substitute these values into equation 2

V2 = (2/29)120

V2 = 8.28 V

Hence the rms output voltage of the transformer = 8.28 V

Alpha particles (charge = +2e, mass = 6.68 × 10-27 kg) are accelerated in a cyclotron to a final orbit radius of 0.30 m. The magnetic field in the cyclotron is 0.80 T. The period of the circular motion of the alpha particles is closest to: A. 0.25 μs B. 0.16 μs C. 0.49 μs D. 0.40 μs E. 0.33 μs

Answers

Answer:

Option B: T ≈ 0.16 μs

Explanation:

We are given;

Mass; m = 6.68 × 10^(-27) kg

Magnetic field;B = 0.80 T

Charge;q = 2e

Now, e is the charge on an electron and it has a value of 1.6 × 10^(-19) C

So, q = 2 × 1.6 × 10^(-19)

q = 3.2 × 10^(-19) C

The period of the circular motion of the alpha particles moving along a in the presence of the magnetic field is given by;

T = 2πm/qB

Where ;

m, q and B are as stated earlier.

Plugging in the relevant values, we have;

T = (2π × 6.68 × 10^(-27))/(3.2 × 10^(-19) × 0.8)

T = 0.16395 × 10^(-6) s

This can also be written as;

T ≈ 0.16 μs

2. The nuclear model of the atom held that
a. electrons were randomly spread through "a sphere of uniform positive
electrification."
b. matter was made of tiny electrically charged particles that were smaller than the
atom
C. matter was made of tiny, indivisible particles.
d. the atom had a dense, positively charged nucleus.​

Answers

Answer:

the atom had a dense, positively charged nucleus.​

Explanation:

Ernest Rutherford, based on the experiment carried out by two of his graduate students, established the authenticity of the nuclear model of the atom.

According to the nuclear model, an atom is made up of a dense positive core called the nucleus. Electrons are found to move round this nucleus in orbits. This is akin to the movement of the planets round the sun in the solar system.

An LR circuit consists of a 35-mH inductor, a resistance of 12 ohms, an 18-V battery, and a switch. What is the current 5.0 ms after the switch is closed

Answers

Answer:

Current, I = 1.23 A

Explanation:

Given that,

Inductance, L = 35 mH

Resistance, R = 12 ohms

Potential difference, V = 18 V

We need to find current 5 ms after the switch is closed. Current in LR circuit is given by :

[tex]I=I_o(1-e^{-t/\tau })[/tex] ....(1)

Here,

[tex]I_o[/tex] is final current

[tex]I_o=\dfrac{V}{R}\\\\I_o=\dfrac{18}{12}=1.5\ A[/tex]

[tex]\tau[/tex] is time constant

[tex]\tau=\dfrac{L}{R}\\\\\tau=\dfrac{35\times 10^{-3}}{12}\\\\\tau=0.00291\ s[/tex]

So, equation (1) becomes :

[tex]I=1.5\times (1-e^{-5\times 10^{-3}/0.00291})\\\\I=1.23\ A[/tex]

So, after 5 ms the current in the circuit is 1.23 A.

An 1,820 W toaster, a 1,420 W electric frying pan, and a 55 W lamp are plugged into the same outlet in a 15 A, 120 V circuit. (The three devices are in parallel when plugged into the same socket.)

Required:
a. What current is drawn by each device?
b. Will this combination blow the 15-A fuse?

Answers

Answer:

toaster- 15.1A

electric frying pan- 11.8 A

lamp- 0.5 A

b) The combination will blow the fuse.

Explanation:

When devices are connected in parallel, the potential difference across each of the devices is the same but the current through each is different. Hence;

V= 120 V

Power= IV

For the toaster;

I= 1820/120 = 15.1 A

For the electric frying pan;

I= 1420/120 = 11.8 A

For the lamp;

55/120 = 0.5 A

Total current = 15.1 +11.8 + 0.5 = 27.4 A

The combination will blow the fuse.

Explanation:    

step one:

Given data

power of toaster= 1,820 W  

power of electric frying pan= 1,420 W  

power of lamp= 55 W  

current of the outlet= 15 A

voltage of outlet = 120 V

step two

since all  three appliances are connected in parallel to the socket outlet, they will use the same voltage of 120 V and the currents will be different across each appliance,

Hence the current across the Toaster will be I₁

using P=I₁V we have

I₁= P/V

I₁= 1820/120 =  15.16 A

A. The current drawn by each device

the current across the  electric frying pan will be I₂

using P=I₂V we have

I₂= P/V

I₂= 1420/120 =  11.83 A

the current across the   lamp will be I₃

using P=I₃V we have

I₃= P/V

I₃= 55/120 =  0.45 A

therefore the total current drawn by all appliances will be

Total current = I₁+I₂+I₃= 15.16 +11.83+ 0.45= 27.44

B.  Will this combination blow the 15-A fuse?

27.44 A > 15 A by 45% ...and this will make fuse to blow

zeugen and yardang differences​

Answers

Answer:

Yardangs are formed on vertical strata while zeugen on horizontal strata. ... Yardangs are formed on vertical hard/soft layers of rock, while zeugen (this is its plural form) are formed on horizontal bands of hard/soft rocks giving it a more mushroom-like shape. The Great Sphinx of Giza has been sculpted in a yardang

A long straight solenoid has 800 turns. When the current in the solenoid is 2.90 amperes the average flux through each turn is 3.25×10−3Wb.
A. What is the inductance of the coil?
B. What must be the magnitude fo the rate of change of the current (di/dt) in order for the self-induced emf to equal 7.50 mV?

Answers

Answer:

Explanation:

Relation between flux and inductance is as follows

φ = Li

where φ is flux associated with induction of inductance L when a current i flows through it

putting the values

3.25 x 10⁻³ x 800 = L x 2.9

L = .9 H

for induced emf in an induction , the relation is

emf induced = L di / dt

Putting the values

7.5 x 10⁻³ = .9 x di / dt

di / dt = 8.33 x 10⁻³ A / s

(a) The self inductance of the solenoid is 0.897 H.

(b) The magnitude of the rate of change of the current is 0.00836 A/s.

The given parameters;

number of turns, N = 800 turnscurrent in the solenoid, I = 2.9 flux through the solenoid, Ф = 3.25 x 10⁻³ Wb

The self inductance of the solenoid is calculated as follows;

[tex]emf = \frac{d\phi}{dt}\\\\emf = \frac{Ldi}{dt} \\\\d\phi = Ldi\\\\\phi = BA\\\\NBA = LI\\\\L = \frac{NBA}{I} \\\\L = \frac{N\phi}{I} \\\\L = \frac{800 \times 3.25\times 10^{-3}}{2.9} \\\\L = 0.897 \ H\\\\[/tex]

The magnitude of the rate of change of the current is calculated as follows;

[tex]emf = L \frac{di}{dt} \\\\\frac{di}{dt} \ = \frac{emf}{L} \\\\\frac{di}{dt} = \frac{7.5 \times 10^{-3}}{0.897} \\\\\frac{di}{dt} = 0.00836 \ A/s[/tex]

Learn more here:https://brainly.com/question/17086348

g Calculate the maximum wavelength of light that will cause the photoelectric effect for potassium. Potassium has work function 2.29 eV = 3.67 x 10–19 J.

Answers

Answer:

λ = 5.4196 10⁻⁷m,  λ = 541.96 nm    this is green ligh

Explanation:

The photoelectric effect was explained by Eintein assuming that the light was made up of particles called photons and these collided with the electrons taking them out of the material.

 

                     K = h f -Ф

where K is the kinetic energy of the ejected electrons, hf is the energy of the light quanta and fi is the work function of the material.

The speed of light is related to wavelength and frequency

                   c = λ / f

                  f = c /λ

we substitute

                K = h c / λ - Φ

for the case that they ask us the kinetic energy of the electons is zero (K = 0)

                 h c / λ = Ф

                λ = h c / Ф

we calculate

                 λ = 6.63 10⁻³⁴  3 10⁸ / 3.67 10⁻¹⁸

                 λ = 5.4196 10⁻⁷m

let's take nm

                lam = 541.96 nm

this is green light

Calculate the wavelength of light that has its third minimum at an angle of 30.0º when falling on double slits separated by 3.00 µm.

Answers

Answer:

λ = 428.6 nm

Explanation:

Hello,

In this case, we must remember that the Young's double slit experiment is described by the expression :

d sin θ = m λ

For constructive interference , and:

d sin θ = (m + ½) λ          

For destructive interference , whereas d accounts for the distance between the slits, λ for the wavelength and m for an integer that describes the order of interference . Thus, for the given angle 30º, the distance between the slits is 3.00 μm or 3.00 10⁻⁶ m and the order of interference is 3; we therefore use the destructive interference equation  to compute the wavelength as shown below:

λ = 3x10⁻⁶ sin (30) / (3 +1/2)

λ = 4.286 10⁻⁷ m

Or in manometers:

λ = 428.6 nm

Best regards.

A current of 5 A is flowing in a 20 mH inductor. The energy stored in the magnetic field of this inductor is:_______

a. 1J.
b. 0.50J.
c. 0.25J.
d. 0.
e. dependent upon the resistance of the inductor.

Answers

Answer:

C. 0.25J

Explanation:

Energy stored in the magnetic field of the inductor is expressed as E = 1/2LI² where;

L is the inductance

I is the current flowing in the inductor

Given parameters

L = 20mH = 20×10^-3H

I = 5A

Required

Energy stored in the magnetic field.

E = 1/2 × 20×10^-3 × 5²

E = 1/2 × 20×10^-3 × 25

E = 10×10^-3 × 25

E = 0.01 × 25

E = 0.25Joules.

Hence the energy stored in the magnetic field of this inductor is 0.25Joules

Determine the value of the current in the solenoid so that the magnetic field at the center of the loop is zero tesla. Justify your answer.

Answers

Answer:

I will explain the concept of magnetic field and how it can be calculated.

Explanation:

The formula for magnetic field at the center of a loop is given as

B = μ[tex]_{o}[/tex]I / 2R

where B is the magnetic field

R is the radius of the loop

I is the current

and μ[tex]_{o}[/tex] is the magnetic permeability of free space which is a constant 4π × [tex]10^{-7}[/tex] newtons/ampere²

If the magnetic field at the center of the loop is 0, then μ[tex]_{o}[/tex]I = 0

I = 0 which means there will be no current flow in the loop.

If the rods with diameters and lengths listed below are made of the same material, which will undergo the largest percentage length change given the same applied force along its length?a. d, 3L b. 3d, L c. 2d, 2L d. 4d, L

Answers

Answer:

The highest percentage of change corresponds to the thinnest rod, the correct answer is a

Explanation:

For this exercise we are asked to change the length of the bar by the action of a force applied along its length, in this case we focus on the expression of longitudinal elasticity

               F / A = Y ΔL/L

where F / A is the force per unit length, ΔL / L is the fraction of the change in length, and Y is Young's modulus.

In this case the bars are made of the same material by which Young's modulus is the same for all

              ΔL / L = (F / A) / Y

the area of ​​the bar is the area of ​​a circle

               A = π r² = π d² / 4

               A = π / 4 d²

we substitute

              ΔL / L = (F / Y) 4 /πd²

changing length

               ΔL = (F / Y 4 /π) L / d²

The amount between paracentesis are all constant in this exercise, let's look for the longitudinal change

a) values ​​given d and 3L

               ΔL = cte 3L / d²

               ΔL = cte L /d²  3

To find the percentage, we must divide the change in magnitude by its value and multiply by 100.

                ΔL/L % = [(F /Y  4/π 1/d²) 3L ] / 3L 100

                ΔL/L  % = cte 100%

 

b) 3d and L value, we repeat the same process as in part a

               ΔL = cte L / 9d²

               ΔL = cte L / d² 1/9

               ΔL / L% = cte 100/9

               ΔL / L% = cte 11%

   

c) 2d and 2L value

               ΔL = (cte L / d ½ )/ 2L

               ΔL/L% = cte 100/4

               ΔL/L% = cte 25%

d) value 4d and L

               ΔL = cte L / d² 1/16

                ΔL/L % = cte 100/16

                ΔL/L % = cte 6.25%

   

The highest percentage of change corresponds to the thinnest rod, the correct answer is a

A box is sliding down an incline tilted at a 12° angle above horizontal. The box is initially sliding down the incline at a speed of 1.5 m/s. The coefficient of kinetic friction between the box and the incline is 0.34. How far does the box slide down the incline before coming to rest?

Answers

Answer:

The box will cover a distance of 0.9199m before coming to rest

Explanation:

We are given;

Angle of tilt; θ = 12°

Speed of sliding down; u = 1.5 m/s

Coefficient of kinetic friction; μ = 0.34

We are told that the box is sliding down an incline tilted at a 12° angle above horizontal.

Thus,

The components of the weight of the block would be;

Fx = mg sinθ = mg sin 12

Fy = mg cosθ = mg cos 12

For, the normal force on the block, it will be counter balanced by the Y component of weight of block and so we have;

Normal force; Fn = mg cos 12

Now formula for the frictional force would be given by;

Ff = μmg cos 12

So, Ff = 0.34mg cos 12

So, the net force along the inclined plane is;

Fnet = Fx - Ff

Fnet = mg sin 12 - 0.34mg cos 12

Where Fnet = mass x acceleration.

Thus;

ma = mg sin 12 - 0.34mg cos 12

m will cancel out to give;

a = g sin 12 - 0.34g cos 12

a = 9.81(0.2079) - 0.34(9.81 × 0.9781)

a = -1.223 m/s²

According to Newton's equation of motion, we have;

(v² - u²) = 2as

s = (v² - u²)/2a

Final velocity is zero. Thus;

s = (0² - 1.5²)/(2 × -1.223)

s = -2.25/-2.446

s = 0.9199 m

Thus, the box will cover 0.9199m before coming to rest

Other Questions
you move left 2 units and right 9 units. you end at (4,5). where did you start? Buenas tardes amigos me llamo Elena pls answerbrainiest guaranteed what is the number if 4 is subtracted from the sum of one fourth of 5 times of 8 and 10 The vast majority of socialists favored:A. Violent revolution of the governmentB. Slow progress through regular political meansC. Separation from the governmentD. Making changes through non-governmental methods The standard entropy of a substance refers to its entropy at:__________.a. absolute zero and 1 bar b. 0C and 1 bar c. 25 C and 1 bar d. 25 C and 0 bar July 1 Purchased merchandise from Boden Company for $6,300 under credit terms of 2/15, n/30, FOB shipping point, invoice dated July 1.2 Sold merchandise to Creek Co. for $1,000 under credit terms of 2/10, n/60, FOB shipping point, invoice dated July 2. The merchandise had cost S567.3 Paid $115 cash for freight charges on the purchase of July 1.8 Sold merchandise that had cost $2, 100 for $2, 500 cash.9 Purchased merchandise from Light Co. for $2, 700 under credit terms of 2/15, n/60, FOB destination, invoice dated July 9.11 Received a $700 credit memorandum from Light Co. for the return of part of the merchandise purchased on July 9.12 Received the balance due from Creek Co. for the invoice dated July 2, net of the discount.16 Paid the balance due to Boden Company within the discount period.19 Sold merchandise that cost $1,000 to Art Co. for $1, 500 under credit terms of 2/15, n/60, FOB shipping point, invoice dated July 19.21 Issued a $250 credit memorandum to Art Co. for an allowance on goods sold on July 19.24 Paid Leight Co. the balance due after deducting the discount.30 Received the balance due from Art Co. for the invoice dated July 19, net of discount.31 Sold merchandise that cost $5, 600 to Creek Co. for $7, 500 under credit terms of 2/10, n/60, FOB shipping point, invoice dated July 31.Required:Prepare journal entries to record the above merchandising transactions of Blink Company, which applies the perpetual inventory system. how many are 4 raised to 3 ??? Luz, who is skydiving, is traveling at terminal velocity with her body parallel to the ground. She then changes her body position to feet first toward the ground. What happens to her motion? She will continue to fall at the same terminal velocity because gravity has not changed. She will slow down because the air resistance will increase and be greater than gravity. She will speed up because air resistance will decrease and be less than gravity. She will begin to fall in free fall because she will have no air resistance acting on her. Based on the data table below, which number would be the BEST choice for the top number of the scale on the vertical axis of a scatter plot showing this data? (PLZ HELP ME UNDERSTAND AND ANSWER THIS:) Read these lines from the poem "Women" and answer the question. Without knowing a page Of it Themselves. How does the poet use the word page in these lines?(A) connotatively, to suggest a type of life experience (B) denotatively, to indicate the parts of a book Drag the tiles to the correct boxes to complete the pairs.The tables show proportional relationships between x and y. Match each table with its constant of proportionality.1 104 20215142 208 404302833012 60645312415 Given that = n M R T, rearrange the equation to solve for V what is the study of the world Which line from President Reagans Address at Moscow State University is a fact? -Democracy is the standard by which governments are measured. -Throughout the world, free markets are the model for growth. -The key is freedomfreedom of thought, freedom of information, freedom of communication. -Every four years the American people choose a new president, and 1988 is one of those years. On a frictionless air track, a 0.30 kg glider moving at 0.40m/s to the right collides with a stationary 0.80kg glider moving at 0.15 m/s to the left. The collision is cushioned by a bumper made of perfectly elastic spring steel. a. What is the velocity of each glider after the collision? b. What is the minimum amount of total kinetic energy during the collision? c. Where is the missing energy? Because of higher gasoline prices, firms using gasoline intensively in the production or distribution of their goods have experienced:_______. The owner of a property creates a deed, leaving the name of the grantee blank, and puts it in a drawer, where it is forgotten for several years. One day, a visitor finds the deed, fills in his name as grantee, and attempts to record it. However, the owner will probably have no trouble disputing the validity of the deed because if the cost of a notebook is 2x-3 express the cost of five books Find x - y subtracted from 0.1. -y-x2. x-y3. -x + y