Answer:
True or False
Explanation:
Because.....
easy 50% chance you are right
a 1010 W radiant heater is constructed to operate at 115 V. (a) What is the current in the heater when the unit is operating?
Answer:
8.78 AmpsExplanation:
Given data:
power rating of the heater P= 1010 W
voltage of the heater V= 115 volts
current taken by the heater I= ?
We can apply the power formula to solve for the current in the heater
i.e P= IV
Making I the current subject of formula we have
I= P/V
Substituting our given data into the expression for I we have
I=1010/115= 8.78 A
Hence the current when the unit/heater is operating is 8.78 Ampwhat is the average flow rate in of gasoline to the engine of a plane flying at 700 km/h if it averages 100.0 km/l
Answer:
1.94cm³/s
Explanation:
1L = 1000cm³
Ihr = 3600s
So
Using
Average flow rate
Fr= 1L/100Km x 700Km/1hr x 1hr/3600s x 1000cm³/ 1L
= 1.94cm³/s
A bungee cord with a spring constant of 800 StartFraction N over m EndFraction stretches 6 meters at its greatest displacement. How much elastic potential energy does the bungee cord have? The bungee cord has J of elastic potential energy.
Explanation:
EE = ½ kx²
EE = ½ (800 N/m) (6 m)²
EE = 14,400 J
Answer:
14,400 J
Explanation:
Its the answer
A semi-circular loop consisting of one turn of wire is place in the x-y plane. A constant magnetic field B=1.7T points along the negative z-axis(into the page), and a current I=0.7A flows counterclockwisefrom the positive z-axis. The net magnetic force on the circular section of the loop points in what direction? What is the net magnetice force on the circular section of the loop?
Answer:
The direction of net magnetic force on the circular section of the loop is in the positive y-axis
The net magnetic force on the circular section of the loop is 3.74 N
Explanation:
The magnetic field strength [tex]B[/tex] = 1.7 T
the current [tex]I[/tex] = 0.7 A
The diameter of the loop = 2 m
the length of the circular section of the semi-circular loop [tex]l[/tex] = πd/2
==> [tex]l[/tex] = (3.142 x 2)/2 = 3.142 m
The force on the semi-circular is given as
F = [tex]BIl[/tex] sin ∅
but the loop is perpendicular to the field, therefore
sin ∅ = sin 90° = 1
F = 1.7 x 0.7 x 3.142 x 1 = 3.74 N
The right hand rule states that "if the fingers of the right hand are held parallel to each other in the direction of the magnetic field, and the thumb is held at right angle to the other fingers in the direction of the flow of current. The palm will push in the direction of the magnetic force on the conductor".
According to the right hand rule, the direction of net magnetic force on the circular section of the loop is in the positive y-axis
An electrostatic paint sprayer contains a metal sphere at an electric potential of 25.0 kV with respect to an electrically grounded object. Positively charged paint droplets are repelled away from the paint sprayer's positively charged sphere and towards the grounded object. What charge must a 0.168-mg drop of paint have so that it will arrive at the object with a speed of 18.8 m/s
Answer:
The charge is [tex]Q = 2.177 *10^{-9} \ C[/tex]
Explanation:
From the question we are told that
The electric potential is [tex]V = 25.0 \ kV = 25.0 *10^{3}\ V[/tex]
The mass of the drop is [tex]m = 0.168 \ m g = 0.168 *10^{-3} \ g = 0.168 *10^{-6}\ kg[/tex]
The speed is [tex]v = 18.8 \ m/s[/tex]
Generally the charge on the paint drop due to the electric potential which will give it the speed stated in the question is mathematically represented as
[tex]Q = \frac{m v^2 }{ 2 * V }[/tex]
Substituting values
[tex]Q = \frac{0.168 *10^{-6} (18)^2 }{ 2 * 25*10^3 }[/tex]
[tex]Q = 2.177 *10^{-9} \ C[/tex]
3. Which of the following accurately describes circuits?
O A. In a parallel circuit, the same amount of current flows through each part of the circuit
O B. In a series circuit, the amount of current passing through each part of the circuit may vary
O C. In a series circuit, the current can flow through only one path from start to finish
O D. In a parallel circuit, there's only one path for the current to travel.
Answer:
Option (c)
Explanation:
In a Series circuit, as the components are connected end-to-end ,the current can flow through only one path from start to finish.
(C.) is the only correct statement in the list of choices.
In a series circuit, the current can flow through only one path from start to finish.
Two football teams, the Raiders and the 49ers are engaged in a tug-of-war. The Raiders are pulling with a force of 5000N. Which of the following is an accurate statement?
A. The tension in the rope depends on whether or not the teams are in equilibrium.
B. The 49ers are pulling with a force of more than 5000N because of course they’d be winning.
C. The 49ers are pulling with a force of 5000N.
D. The tension in the rope is 10,000N.
E. None of these statements are true.
Answer:
E. None of these statements are true.
Explanation:
We can't say the exact or approximate amount of tension on the rope, since we do know for sure from the statement who is winning.
for A, the tension on the rope does not depend on if both teams pull are in equilibrium.
for B, the 49ers would be pulling with a force more than 5000 N, if they were winning. The problem is that we can't say with all confidence that they'd be winning.
for C, we don't know how much tension exists on the rope, and its direction, so we can't work out how much tension the 49ers are pulling the rope with.
for D, just as for C above, we can't work out how much tension there is on the rope, since we do not know how much force the 49ers are pulling with.
we go with option E.
A mechanic wants to unscrew some bolts. She has two wrenches available: one is 35 cm long, and one is 50 cm long. Which wrench makes her job easier and why?
Answer:
50 cm long
When 35cm long wrench is compared to 50cm long wrench, we find that the 50cm long wrench produces more turning effect of force because it has longer distance between fulcrum and line of action of force. At conclusion, the more the turning effect of force the more it is easy to unscrew bolts.
Consider a wire of a circular cross-section with a radius of R = 3.17 mm. The magnitude of the current density is modeled as J = cr2 = 9.00 ✕ 106 A/m4 r2. What is the current (in A) through the inner section of the wire from the center to r = 0.5R?
Answer:
The current is [tex]I = 8.9 *10^{-5} \ A[/tex]
Explanation:
From the question we are told that
The radius is [tex]r = 3.17 \ mm = 3.17 *10^{-3} \ m[/tex]
The current density is [tex]J = c\cdot r^2 = 9.00*10^{6} \ A/m^4 \cdot r^2[/tex]
The distance we are considering is [tex]r = 0.5 R = 0.001585[/tex]
Generally current density is mathematically represented as
[tex]J = \frac{I}{A }[/tex]
Where A is the cross-sectional area represented as
[tex]A = \pi r^2[/tex]
=> [tex]J = \frac{I}{\pi r^2 }[/tex]
=> [tex]I = J * (\pi r^2 )[/tex]
Now the change in current per unit length is mathematically evaluated as
[tex]dI = 2 J * \pi r dr[/tex]
Now to obtain the current (in A) through the inner section of the wire from the center to r = 0.5R we integrate dI from the 0 (center) to point 0.5R as follows
[tex]I = 2\pi \int\limits^{0.5 R}_{0} {( 9.0*10^6A/m^4) * r^2 * r} \, dr[/tex]
[tex]I = 2\pi * 9.0*10^{6} \int\limits^{0.001585}_{0} {r^3} \, dr[/tex]
[tex]I = 2\pi *(9.0*10^{6}) [\frac{r^4}{4} ] | \left 0.001585} \atop 0}} \right.[/tex]
[tex]I = 2\pi *(9.0*10^{6}) [ \frac{0.001585^4}{4} ][/tex]
substituting values
[tex]I = 2 * 3.142 * 9.00 *10^6 * [ \frac{0.001585^4}{4} ][/tex]
[tex]I = 8.9 *10^{-5} \ A[/tex]
A sinusoidal sound wave moves through a medium and is described by the displacement wave function s(x, t) = 1.99 cos(15.2x − 869t) where s is in micrometers, x is in meters, and t is in seconds. (a) Find the amplitude of this wave. µm (b) Find the wavelength of this wave. cm (c) Find the speed of this wave. m/s (d) Determine the instantaneous displacement from equilibrium of the elements of the medium at the position x = 0.050 9 m at t = 2.94 ms. µm (e) Determine the maximum speed of a element's oscillatory motion. mm/s
Answer:
a) A = 1.99 μm , b) λ = 0.4134 m , c) v = 57.2 m / s , d) s = - 1,946 nm ,
e) v_max = 1,739 mm / s
Explanation:
A sound wave has the general expression
s = s₀ sin (kx - wt)
where s is the displacement, s₀ the amplitude of the wave, k the wave vector and w the angular velocity, in this exercise the expression given is
s = 1.99 sin (15.2 x - 869 t)
a) the amplitude of the wave is
A = s₀
A = 1.99 μm
b) wave spectrum is
k = 2π /λ
in the equation k = 15.2 m⁻¹
λ = 2π / k
λ = 2π / 15.2
λ = 0.4134 m
c) the speed of the wave is given by the relation
v = λ f
angular velocity and frequency are related
w = 2π f
f = w / 2π
f = 869 / 2π
f = 138.3 Hz
v = 0.4134 138.3
v = 57.2 m / s
d) To find the instantaneous velocity, we substitute the given distance and time into the equation
s = 1.99 sin (15.2 0.0509 - 869 2.94 10⁻³)
s = 1.99 sin (0.77368 - 2.55486)
remember that trigonometry functions must be in radians
s = 1.99 (-0.98895)
s = - 1,946 nm
The negative sign indicates that it shifts to the left
e) the speed of the oscillating part is
v = ds / dt)
v = - s₀(-w) cos (kx -wt)
the maximum speed occurs when the cosines is 1
v_maximo = s₀w
v_maximum = 1.99 869
v_maximo = 1739.31 μm / s
let's reduce to mm / s
v_maxio = 1739.31 miuy / s (1 mm / 103 mu)
v_max = 1,739 mm / s
a) A is = 1.99 μm , b) λ is = 0.4134 m , c) v is = 57.2 m / s , d) s is = - 1,946 nm, e) v_max is = 1,739 mm / s
Calculation of Wavelength
When A sound wave has the general expression is:
Then, s = s₀ sin (kx - wt)
Now, where s is the displacement, Then, s₀ is the amplitude of the wave, k the wave vector, and w the angular velocity, Now, in this exercise the expression given is
s is = 1.99 sin (15.2 x - 869 t)
a) When the amplitude of the wave is
A is = s₀
Thus, A = 1.99 μm
b) When the wave spectrum is
k is = 2π /λ
Now, in the equation k = 15.2 m⁻¹
Then, λ = 2π / k
After that, λ = 2π / 15.2
Thus, λ = 0.4134 m
c) When the speed of the wave is given by the relation is:
Then, v = λ f
Now, the angular velocity and frequency are related is:
w is = 2π f
Then, f = w / 2π
After that, f = 869 / 2π
Now, f = 138.3 Hz
Then, v = 0.4134 138.3
Thus, v = 57.2 m / s
d) Now, To find the instantaneous velocity, When we substitute the given distance and time into the equation
Then, s = 1.99 sin (15.2 0.0509 - 869 2.94 10⁻³)
After that, s = 1.99 sin (0.77368 - 2.55486)
Then remember that trigonometry functions must be in radians
After that, s = 1.99 (-0.98895)
Thus, s = - 1,946 nm
When The negative sign indicates that it shifts to the left
e) When the speed of the oscillating part is
Then, v = ds / dt)
Now, v = - s₀(-w) cos (kx -wt)
When the maximum speed occurs when the cosines is 1
Then, v_maximo = s₀w
After that, v_maximum = 1.99 869
v_maximo = 1739.31 μm / s
Now, let's reduce to mm / s
Then, v_maxio = 1739.31 miuy / s (1 mm / 103 mu)
Therefore, v_max = 1,739 mm / s
Finf more informmation about Wavelength here:
https://brainly.com/question/6352445
The ceiling of your lecture hall is probably covered with acoustic tile, which has small holes separated by about 6.1 mm. Using light with a wavelength of 578 nm, how far could you be from this tile and still resolve these holes
Answer:
8.65x10^3m
Explanation:
See attached file
A stationary coil is in a magnetic field that is changing with time. Does the emf induced in the coil depend
Answer:
Explanation:
The e.m.f induced in the coil depend on the following :
(a) No. of turns in the coil
(b) Cross-sectional Area of the coil
(c) Magnitude of Magnetic field
(d) Angular velocity of the coil
In a two-slit experiment, the slit separation is 3.34 ⋅ 10 − 5 m. The interference pattern is created on a screen that is 3.30 m away from the slits. If the 7th bright fringe on the screen is 29.0 cm away from the central fringe, what is the wavelength of the light?
Answer:
The wavelength is [tex]\lambda = 419 \ nm[/tex]
Explanation:
From the question we are told that
The distance of separation is [tex]d = 3.34 *10^{-5} \ m[/tex]
The distance of the screen is [tex]D = 3.30 \ m[/tex]
The order of the fringe is n = 7
The distance of separation of fringes is y = 29.0 cm = 0.29 m
Generally the wavelength of the light is mathematically represented as
[tex]\lambda = \frac{y * d }{ n * D}[/tex]
substituting values
[tex]\lambda = \frac{0.29 * 3.34*10^{-5} }{ 7 * 3.30}[/tex]
[tex]\lambda = 4.19*10^{-7}\ m[/tex]
[tex]\lambda = 419 \ nm[/tex]
Equipotential lines are lines with equal electric potential (for example, all the points with an electric potential of 5.0 V). Using the plot tool that comes with voltmeter (pencil icon) make two equipotential lines at r = 0.5 m and r = 1.5 m. Enable electric field vectors in the simulation. Put an electric field sensor at different points on the equipotential line and note the direction of the electric field vector. What can you conclude about the direction of the electric field vector in relation to the equipotential lines?
The direction for each field vector is perpendicular to equipotential lines.
Take a snapshot of the simulation showing equipotential lines and paste to a word document.
....................
Suppose you observed the equation for a traveling wave to be y(x, t) = A cos(kx − ????t), where its amplitude of oscillations was 0.15 m, its wavelength was two meters, and the period was 2/15 s. If a point on the wave at a specific time has a displacement of 0.12 m, what is the transverse speed of that point?
Answer:
15m/sExplanation:
The equation for a traveling wave as expressed as y(x, t) = A cos(kx − [tex]\omega[/tex]t) where An is the amplitude f oscillation, [tex]\omega[/tex] is the angular velocity and x is the horizontal displacement and y is the vertical displacement.
From the formula; [tex]k =\frac{2\pi x}{\lambda} \ and \ \omega = 2 \pi f[/tex] where;
[tex]\lambda \ is\ the \ wavelength \ and\ f \ is\ the\ frequency[/tex]
Before we can get the transverse speed, we need to get the frequency and the wavelength.
frequency = 1/period
Given period = 2/15 s
Frequency = [tex]\frac{1}{(2/15)}[/tex]
frequency = 1 * 15/2
frequency f = 15/2 Hertz
Given wavelength [tex]\lambda[/tex] = 2m
Transverse speed [tex]v = f \lambda[/tex]
[tex]v = 15/2 * 2\\\\v = 30/2\\\\v = 15m/s[/tex]
Hence, the transverse speed at that point is 15m/s
A single-slit diffraction pattern is formed on a distant screen. Assuming the angles involved are small, by what factor will the width of the central bright spot on the screen change if the slit width is doubled
Answer:
y ’= y / 2
thus when the slit width is doubled the pattern width is halved
Explanation:
The diffraction of a slit is given by the expressions
a sin θ = m λ
where a is the width of the slit, λ is the wavelength and m is an integer that determines the order of diffraction.
sin θ = m λ / a
If this equation
a ’= 2 a
we substitute
2 a sin θ'= m λ
sin θ'= (m λ / a) 1/2
sin θ ’= sin θ / 2
We can use trigonometry to find the width
tan θ = y / L
as the angle is small
tan θ = sin θ / cos θ = sin θ
sin θ = y / L
we substitute
y ’/ L = y/L 1/2
y ’= y / 2
thus when the slit width is doubled the pattern width is halved
A metal sphere A of radius a is charged to potential V. What will be its potential if it is enclosed by a spherical conducting shell B of radius b and the two are connected by a wire?
Answer:
The potential will be Va/b
Explanation:
So Let sphere A charged Q to potential V.
so, V= KQ/a. ....(1
Thus, spherical shell B is connected to the sphere A by a wire, so all charge always reside on the outer surface.
therefore, potential will be ,
V ′ = KQ/b = Va/b... That is from .....(1), KQ=Va]
If you wanted to make your own lenses for a telescope, what features of a lens do you think would affect the images that you can see
Answer:
Therefore the characteristics to be found are:
* the focal length must be large and the focal length of the eyepiece must be small
* The diameter of the objective lens should be as large as possible, to be able to collect small without need from light
* The system must be configured to the far sight tip,
Explanation:
The length of the telescope is
L = f_ocular + f_objetive
the magnification of the telescope is
m = - f_objective / f_ocular
These are the two equations that describe the behavior of the telescope. Therefore the characteristics to be found are:
* the focal length must be large and the focal length of the eyepiece must be small
* The diameter of the objective lens should be as large as possible, to be able to collect small without need from light
* The system must be configured to the far sight tip,
How much heat is required to convert 5.0 kg of ice from a temperature of - 20 0C to water at a temperature of 205 0F
Answer:
Explanation:
To convert from °C to °F , the formula is
( F-32 ) / 9 = C / 5
F is reading fahrenheit scale and C is in centigrade scale .
F = 205 , C = ?
(205 - 32) / 9 = C / 5
C = 96°C approx .
Let us calculate the heat required .
Total heat required = heat required to heat up the ice at - 20 °C to 0°C + heat required to melt the ice + heat required to heat up the water at 0°C to
96°C.
= 5 x 2.04 x (20-0) + 5 x 336 + 5 x ( 96-0 ) x 4.2 kJ .
= 204 + 1680 + 2016
= 3900 kJ .
You want the current amplitude through a 0.450 mH inductor (part of the circuitry for a radio receiver) to be 1.50 mA when a sinusoidal voltage with an amplitude of 13.0 V is applied across the inductor. What frequency is required?
Answer:
3.067MHzExplanation:
The formula for calculating the voltage across an inductor is expressed as
[tex]V_l = IX_l\\\\Since\ X_l = 2\pi fL\\V_l = I(2\pi fL)[/tex]
Given parameters
current amplitude I = 1.50mA = 1.5*10⁻³A
inductance L = 0.450mH = 0.450*10⁻³H
Voltage across the inductor [tex]V_l[/tex] = 13.0V
Required
frequency f
Substituting the given parametres into the formula, we have;
[tex]V_l = I(2\pi fL)\\\\13 = 1.50*10^{-3}(2*3.14*f*0.450*10^{-3})\\\\13 = 4.239*10^{-6}f\\\\f = \frac{13}{4.239*10^{-6}} \\\\f = 3,066,761 Hertz\\\\f = 3.067MHz[/tex]
Hence, the frequency required is 3.067MHz
Two blocks A and B have a weight of 11 lb and 5 lb , respectively. They are resting on the incline for which the coefficients of static friction are μA = 0.16 and μB = 0.23. Determine the incline angle θ for which both blocks begin to slide. Also find the required stretch or compression in the connecting spring for this to occur. The spring has a stiffness of k = 2.1 lb/ft .
Answer:
[tex]\theta=10.20^{\circ}[/tex]
[tex]\Delta l=0.10 ft[/tex]
Explanation:
First of all, we analyze the system of blocks before starting to move.
[tex]\Sum F_{x}=P_{A}sin(\theta)+P_{B}sin(\theta)-F_{fA}-F_{fB}=0[/tex]
[tex]\Sum F_{x}=11sin(\theta)+5sin(\theta)-0.16N_{A}-0.23N_{B}=0[/tex]
[tex]11sin(\theta)+5sin(\theta)-0.16P_{A}cos(\theta)-0.23P_{B}cos(\theta)=0[/tex]
[tex]11sin(\theta)+5sin(\theta)-0.16*11cos(\theta)-0.23*5cos(\theta)=0[/tex]
[tex]11sin(\theta)+5sin(\theta)-0.16*11cos(\theta)-0.23*5cos(\theta)=0[/tex]
[tex]16sin(\theta)-2.91cos(\theta)=0[/tex]
[tex]tan(\theta)=0.18[/tex]
[tex]\theta=arctan(0.18)[/tex]
[tex]\theta=10.20^{\circ}[/tex]
Hence, the incline angle θ for which both blocks begin to slide is 10.20°.
Now, if we do a free body diagram of block A we have that after the block moves, the spring force must be taken into account.
[tex]P_{A}sin(\theta)-F_{fA}-F_{spring}=0[/tex]
Where:
[tex]F_{spring} = k\Delta l=2.1\Delta l[/tex]
[tex]P_{A}sin(\theta)-0.16*11cos(\theta)-2.1\Delta l=0[/tex]
[tex]\Delta l=\frac{11sin(\theta)-0.16*11cos(\theta)}{2.1}[/tex]
[tex]\Delta l=0.10 ft[/tex]
Therefore, the required stretch or compression in the connecting spring is 0.10 ft.
I hope it helps you!
(a) The inclined angle for which both blocks begin to slide is 10.3⁰.
(b) The compression of the spring is 0.22 ft.
The given parameters;
mass of block A, = 11 lbmass of block B, = 5 lbcoefficient of static friction for A, = 0.16coefficient of static friction for B, = 0.23 spring constant, k = 2.1 lb/ftThe normal force on block A and B:
[tex]F_n_A = m_Agcos \ \theta\\\\F_n_B = m_Bgcos \ \theta[/tex]
The frictional force on block A and B:
[tex]F_f_A = \mu_s_AF_n_A \\\\F_f_B = \mu_s_BF_n_A[/tex]
The net force on the blocks when they starts sliding;
[tex](m_Ag sin \theta+ m_Bgsin\theta) - (F_f_A + F_f_B) = 0\\\\m_Ag sin \theta+ m_Bgsin\theta = F_f_A + F_f_B\\\\m_Ag sin \theta+ m_Bgsin\theta = \mu_Am_Agcos\theta \ + \ \mu_Bm_Bgcos\theta\\\\gsin\theta(m_A + m_B) = gcos\theta (\mu_Am_A + \mu_Bm_B)\\\\\frac{sin\theta}{cos \theta} = \frac{\mu_Am_A\ + \ \mu_Bm_B}{m_A\ + \ m_B} \\\\tan\theta = \frac{(0.16\times 11) \ + \ (0.23 \times 5)}{11 + 5} \\\\tan\theta = 0.1819\\\\\theta = tan^{-1}(0.1819)\\\\\theta = 10.3 \ ^0[/tex]
The change in the energy of the blocks is the work done in compressing the spring;
[tex]\Delta E = W\\\\F_A (sin \theta )d- \mu F_n d= \frac{1}{2} kd^2\\\\F_A sin\theta \ - \ \mu F_A cos\theta = \frac{1}{2} kd\\\\d = \frac{2F_A(sin\theta - \mu cos \theta) }{k} \\\\d = \frac{2\times 11(sin \ 10.3\ - \ 0.16\times cos \ 10.3) }{2.1} \\\\d = 0.22 \ ft[/tex]
Learn more here:https://brainly.com/question/16892315
Electrons are accelerated through a voltage difference of 270 kV inside a high voltage accelerator tube. What is the final kinetic energy of the electrons?
Each electron winds up with kinetic energy of
(270 keV)
plus
(whatever KE it had when it started accelerating).
Question 18(Multiple Choice Worth 2 polnis)
When riding your skateboard you crash into a curb, the skateboard stops, and you continue moving forward. Which law of
motion is being described in this scenario?
O Law of Universal Gravitation
o Newton's Second Law of Motion
o Law of Conservation of Energy
o Newton's First Law of Motion
The metal wire in an incandescent lightbulb glows when the light is switched on and stops glowing when it is switched off. This simple
process is which kind of a change?
OA a physical change
OB. a chemical change
OC. a nuclear change
OD
an ionic change
B. A chemical change
Explanation:
I'm guessing ?
The difference between a DC and an AC generator is that
a. the DC generator has one unbroken slip ring.
b. the AC generator has one unbroken slip ring
c. the DC generator has one slip ring splitin two halves.
d. the AC generator has one slip ring split in two halves.
e The DC generator has twounbroken sip rings
Answer:
The AC generator has one unbroken slip ring
Explanation:
In physics, the application of electromagnetic induction can be seen in generators and dynamos. Electromagnetic induction is the process of generating electricity using magnets. It found applications in generators and the types of generator they found application is in AC and DC generator.
An AC generator is also called a Dynamo. A DC generator contains what is called a SPLIT RING fixed to the end of the coil which can be separated and coupled back according to the name "split". An AC generator also called a Dynamo makes use of a SLIP ring which cannot be divided into two. It comes as an entity. The presence of this rings is what differentiates a DC generator from an AC generator.
We can replace split rings with slip rings when converting a DC generator to an AC generator and vice versa.
It can therefore be concluded that the difference between a DC and an AC generator is that the AC generator has one unbroken slip ring.
An airplane flies 1,592 miles east from Phoenix, Arizona, to Atlanta, Georgia, in 3.68 hours.
What is the average velocity of the airplane? Round your answer to the nearest whole number.
Answer:
433
Explanation:
The advantage of a hydraulic lever is A : it transforms a small force acting over a large distance into a large force acting over a small distance. B : it transforms a small force acting over a small distance into a large force acting over a large distance. C : it allows you to exert a larger force with less work. D : it transforms a large force acting over a large distance into a small force acting over a small distance. E : it transforms a large force acting over a small distance into a small force acting over a large distance.
Answer:
A) it transforms a small force acting over a large distance into a large force acting over a small distance.
Explanation:
The hydraulic lever works based on Pascal's law of transmission of pressure through a fluid. In the hydraulic lever, the pressure transmitted is the same.
Pressure transmitted P = F/A
where F is the force applied
and A is the area over which the force is applied.
This pressure can be manipulated on the input end as a small force applied over a small area, and then be transmitted to the output end as a large force over a large area.
F/A = f/a
where the left side of the equation is for the output, and the right side is for the input.
The volume of the displaced fluid will be the same on both ends of the hydraulic lever. Since we know that
volume V = (area A) x (distance d)
this means that the the piston on the input smaller area of the hydraulic lever will travel a greater distance, while the piston on the larger output area of the lever will travel a small distance.
From all these, we can see that the advantage of a hydraulic lever is that it transforms a small force acting over a large distance into a large force acting over a small distance.
A car moving at 36 m/s passes a stationary police car whose siren has a frequency of 500 Hz. What is the change in the frequency (in Hz) heard by an observer in the moving car as he passes the police car? (The speed of sound in air is 343 m/s.)
Answer:
Change in the frequency (in Hz) = 104.96 Hz
Explanation:
Given:
Speed of sound in air (v) = 343 m/s
Speed of car (v1) 36 m/s
Frequency(f) = 500 Hz
Find:
Change in the frequency (in Hz)
Computation:
Frequency hear by the observer(before)(f1) = [f(v+v1)] / v
Frequency hear by the observer(f1) = [500(343+36)] / 343
Frequency hear by the observer(f1) = 552.48 Hz
Frequency hear by the observer(after)(f2) = [f(v-v1)] / v
Frequency hear by the observer(f2) = [500(343-36)] / 343
Frequency hear by the observer(f2) = 447.52 Hz
Change in the frequency (in Hz) = f1 - f2
Change in the frequency (in Hz) = 552.48 Hz - 447.52 Hz
Change in the frequency (in Hz) = 104.96 Hz
You perform a double‑slit experiment in order to measure the wavelength of the new laser that you received for your birthday. You set your slit spacing at 1.11 mm and place your screen 8.63 m from the slits. Then, you illuminate the slits with your new toy and find on the screen that the tenth bright fringe is 4.71 cm away from the central bright fringe (counted as the zeroth bright fringe). What is your laser's wavelength lambda expressed in nanometers?
Answer:
λ = 605.80 nm
Explanation:
These double-slit experiments the equation for constructive interference is
d sin θ = m λ
where d is the distance between the slits, λ the wavelength of light and m an integer that determines the order of interference.
In this case, the distance between the slits is d = 1.11 mm = 1.11 10⁻³ m, the distance to the screen is L = 8.63 m, the range number m = 10 and ay = 4.71 cm
Let's use trigonometry to find the angle
tan θ = y / L
as the angles are very small
tan θ = sin θ / cos θ = sin θ
we substitute
sin θ = y / L
we substitute in the first equation
d y / L = m λ
λ = d y / m L
let's calculate
λ = 1.11 10⁻³ 4.71 10⁻²/ (10 8.63)
λ = 6.05805 10⁻⁷ m
let's reduce to nm
λ = 6.05805 10⁻⁷ m (10⁹ nm / 1m)
λ = 605.80 nm
With the same block-spring system from above, imagine doubling the displacement of the block to start the motion. By what factor would the following change?
A. Kinetic energy when passing through the equilibrium position.
B. Speed when passing through the equilibrium position.
Answer:
A) K / K₀ = 4 b) v / v₀ = 4
Explanation:
A) For this exercise we can use the conservation of mechanical energy
in the problem it indicates that the displacement was doubled (x = 2xo)
starting point. At the position of maximum displacement
Em₀ = Ke = ½ k (2x₀)²
final point. In the equilibrium position
[tex]Em_{f}[/tex] = K = ½ m v²
Em₀ = Em_{f}
½ k 4 x₀² = K
(½ K x₀²) = K₀
K = 4 K₀
K / K₀ = 4
B) the speed value
½ k 4 x₀² = ½ m v²
v = 4 (k / m) x₀
if we call
v₀ = k / m x₀
v = 4 v₀
v / v₀ = 4
