Explanation:
Yes, the law of conservation of energy still applies even if there is waste energy.
The waste energy are the transformation products of energy from one form to another.
According to the law of conservation of energy "energy is neither created nor destroyed by transformed from one form to another in a system".
But of then times, energy is lost as heat or sound within a system.
If we take into account these waste energy, we can see that energy is indeed conserved. The sum total of the energy generated and those produced will be the same if we factor in other forms in which the energy has been transformed into.Why does it rain more in West Ferris than in East Ferris? Explain your answer.
Answer:
This idea helps students explain why more rain forms over West Ferris than East Ferris. ... Therefore, when students explain that water vapor condenses higher in the atmosphere, they are actually explaining that water vapor condenses high in the troposphere, which is relatively low in the atmosphere.
Explanation:
Plz mark me brainliest thank u> have a good day
How do you calculate area when pressure and force are given to you
Answer:
This is my answer
Explanation:
First convert 150 kPa to Pa:
150 × 1,000 = 150,000.
Next substitute the values into the equation:
force normal to a surface area = pressure × area of that surface.
force = 150,000 × 180.
force = 27,000,000 N.
1.First convert 150kPato Pa:
2.150 x 1,000 + 150,000
3.next substitute the values into the equations:
4.force normal to a surface area =pressure x area of that surface.
5.force=150,000 x 180.
6.force = 27,000,000N.
can i have brainliest please
What energy store is in the torch
BEFORE it gets switched on?
Answer:
Chemical energy
Explanation:
The energy in the torch is stored as chemical energy before the torch gets switch on.
The chemical energy energy in the battery of cell will power the cell and allows it to produce light.
Chemical energy is a form of potential energy. The electrolytes within the battery are capable of producing electric current. So the chemical energy is transformed into electrical energy which is used to produce the light of the torch.Fluids
A = 2804 cm3 B = 2862 cm2 C = 2916 cm3
Three separate fluids, A, B, and C have been selected at random and each initially fills a 3000 cm3 volume at atmospheric pressure. A gage pressure of 6 x 107 N/m2 is then applied to each fluid. The final volume is given below. Determine which fluids were selected from the given list.
Acetone E = 0.92 GPa Glycerin E = 4.35 GP
Water E = 2.15 GPa Mercury E = 28.5 GPa
Benzene E = 1.05 GPa Sulfuric Acid E = 3.0 GPa
Ethyl Alcohol E = 1.06 GPa Gasoline E = 1.3 GPa
Petrol E = 1.45 GPa Seawater E = 2.34 GPa
Answer:
Explanation:
Fluid A :
Δ V = Change in volume = (3000 - 2804) x 10⁻⁶ m³ = 196 x 10⁻⁶ m³
volume strain = Δ V / V = 196 x 10⁻⁶ / 3000 x 10⁻⁶
= .06533
Δ P = increase in pressure = 6 x 10⁷ Pa
E = Δ P / volume strain = 6 x 10⁷ / .06533 = 91.84 x 10⁷ Pa = .92 GPa .
It is Acetone .
Fluid B :
Δ V = Change in volume = (3000 - 2862) x 10⁻⁶ m³ = 138 x 10⁻⁶ m³
volume strain = Δ V / V = 138 x 10⁻⁶ / 3000 x 10⁻⁶
= .046
Δ P = increase in pressure = 6 x 10⁷ Pa
E = Δ P / volume strain = 6 x 10⁷ / .046 = 130.43 x 10⁷ Pa = 1.3 GPa .
It is Gasoline .
Fluid C :
Δ V = Change in volume = (3000 - 2916) x 10⁻⁶ m³ = 84 x 10⁻⁶ m³
volume strain = Δ V / V = 84 x 10⁻⁶ / 3000 x 10⁻⁶
= .028
Δ P = increase in pressure = 6 x 10⁷ Pa
E = Δ P / volume strain = 6 x 10⁷ / .028 = 214.28 x 10⁷ Pa = 2.14 GPa .
It is Water .
While investigating Kirchhoff's Laws, you begin observing a blackbody, such as a star, from Earth using advanced technology that can analyze spectra. While pointing it at the star with nothing between you and the star, you observe a full spectrum. You come back and repeat this same experiment a year later using the same star, except this time you observe an absorption spectrum. What is the most likely explanation for this
Answer:
the second time there is a gas between you and the star,
Explanation:
When you observe the star for the first time you do not have a given between you and the star, therefore you observe the emission spectrum of the same that is formed by lines of different intensity and position that indicate the type and percentage of the atoms that make up the star.
When you observe the same phenomenon for the second time there is a gas between you and the star, this gas absorbs the wavelengths of the star that has the same energies and the atomisms and molecular gas, therefore these lines are not observed by seeing a series of dark bands,
The information obtained from the two spectra is the same, the type of atoms that make up the star
calculate ine gravitational potential energy of the ball using pe=m×g×h.(use g=9.8 n/kg)
A 4.0-kilogram ball held 1.5 meters above the floor has ________ joules of potential energy
Answer:
58.8J
Explanation:
Given parameters;
Mass of ball = 4kg
Height above the floor = 1.5m
g = 9.8n/kg
Unknown:
Potential energy = ?
Solution:
The potential energy of a body is the energy due to the position of the body.
It is mathematically expressed as:
Potential energy = mass x acceleration due to gravity x height
Potential energy = 4 x 9.8 x 1.5 = 58.8J
Scientists believe that the boundary stratum between the Cretaceous and Paleogene was caused by an asteroid. What evidence is most consistent with this theory?
Answer:
Because there was fewer fossils
Explanation:
Answer:
Actually the answer is "The stratum contains iridium.".
Explanation:
A particle with charge Q and mass M has instantaneous speed uy when it is at a position where the electric potential is V. At a later time, the particle has moved a distance R away to a position where the electric potential is V2 ) Which of the following equations can be used to find the speed uz of the particle at the new position?
a. 1/2M(μ2^2-μ1^2)=Q (v1-v2)
b. 1/2M(μ2^2-μ1^2)^2=Q(v1-v2)
c. 1/2Mμ2^2=Qv1
d. 1/2Mμ2^2=1/4πx0 (Q^2/R)
Answer:
A
Explanation:
Ke = 1/2 MV^2
7. If the impact of the golf club on the ball in the previous question occurs over a time of 2 x 10 seconds, what
force does the ball experience to accelerate from rest to 73 m/s?
Answer:
3.65 x mass
Explanation:
Given parameters:
Time = 20s
Initial velocity = 0m/s
Final velocity = 73m/s
Unknown:
Force the ball experience = ?
Solution:
To solve this problem, we apply the equation from newton's second law of motion:
F = m [tex]\frac{v - u}{t}[/tex]
m is the mass
v is the final velocity
u is the initial velocity
t is the time taken
So;
F = m ([tex]\frac{73 - 0}{20}[/tex] ) = 3.65 x mass
Required
Momentum
The magnitude of the momentum of an object is 64 kg*m/s. If the velocity of the
object is doubled, what will be the magnitude of the momentum of the object? *
32 kg*m/s
64 kg*m/s
128 kg*m/s
256 kg*m/s
Answer:
C) 128 kg*m/s
Explanation:
When you double something you multiply it by 2 most of the time. 64*2=128 or you can add it 64+64=128. Hope this helps.
Two 90.0-kilogram people are separated by 3.00 meters. What is the magnitude of the gravitational force that one person exerts on the other?
Answer:
the magnitude of gravitational force is 6 x 10⁻⁸ N.
Explanation:
Given;
mass of the two people, m₁ and m₂ = 90 kg
distance between them, r = 3.0 m
The magnitude of gravitational force exerted by one person on another is calculated as;
[tex]F = \frac{Gm_1m_2}{r^2} \\\\[/tex]
where;
G is gravitational constant = 6.67 x 10⁻¹¹ Nm²/kg²
[tex]F = \frac{Gm_1m_2}{r^2} \\\\F = \frac{6.67\times 10^{-11} \times \ 90 \ \times \ 90}{3^2} \\\\F = 6\times 10^{-8} \ N[/tex]
Therefore, the magnitude of gravitational force is 6 x 10⁻⁸ N.
6 A test of a driver's perception/reaction time is being conducted on a special testing track with level, wet pavement and a driving speed of 50 mi/h. When the driver is sober, a stop can be made just in time to avoid hitting an object that is first visible 385 ft ahead. After a few drinks under exactly the same conditions, the driver fails to stop in time and strikes the object at a speed of 30 mi/h. Determine the driver's perception/reaction time before and after drinking. (Assume practical stopping distance.)
Answer:
a. 10.5 s b. 6.6 s
Explanation:
a. The driver's perception/reaction time before drinking.
To find the driver's perception time before drinking, we first find his deceleration from
v² = u² + 2as where u = initial speed of driver = 50 mi/h = 50 × 1609 m/3600 s = 22.35 m/s, v = final speed of driver = 0 m/s (since he stops), a = deceleration of driver and s = distance moved by driver = 385 ft = 385 × 0.3048 m = 117.35 m
So, a = v² - u²/2s
substituting the values of the variables into the equation, we have
a = v² - u²/2s
a = (0 m/s)² - (22.35 m/s)²/2(117.35 m)
a = - 499.52 m²/s²/234.7 m
a = -2.13 m/s²
Using a = (v - u)/t where u = initial speed of driver = 50 mi/h = 50 × 1609 m/3600 s = 22.35 m/s, v = final speed of driver = 0 m/s (since he stops), a = deceleration of driver = -2.13 m/s² and t = reaction time
So, t = (v - u)/a
Substituting the values of the variables into the equation, we have
t = (0 m/s - 22.35 m/s)/-2.13 m/s²
t = - 22.35 m/s/-2.13 m/s²
t = 10.5 s
b. The driver's perception/reaction time after drinking.
To find the driver's perception time after drinking, we first find his deceleration from
v² = u² + 2as where u = initial speed of driver = 50 mi/h = 50 × 1609 m/3600 s = 22.35 m/s, v = final speed of driver = 30 mi/h = 30 × 1609 m/3600 s = 13.41 m/s, a = deceleration of driver and s = distance moved by driver = 385 ft = 385 × 0.3048 m = 117.35 m
So, a = v² - u²/2s
substituting the values of the variables into the equation, we have
a = v² - u²/2s
a = (13.41 m/s)² - (22.35 m/s)²/2(117.35 m)
a = 179.83 m²/s² - 499.52 m²/s²/234.7 m
a = -319.69 m²/s² ÷ 234.7 m
a = -1.36 m/s²
Using a = (v - u)/t where u = initial speed of driver = 50 mi/h = 50 × 1609 m/3600 s = 22.35 m/s, v = final speed of driver = 30 mi/h = 30 × 1609 m/3600 s = 13.41 m/s, a = deceleration of driver = -1.36 m/s² and t = reaction time
So, t = (v - u)/a
Substituting the values of the variables into the equation, we have
t = (13.41 m/s - 22.35 m/s)/-1.36 m/s²
t = - 8.94 m/s/-1.36 m/s²
t = 6.6 s
2.19 The drag characteristics of a blimp traveling at 4 m/s are to be studied by experiments in a water tunnel. The prototype is 20 m in diameter and 110 m long. The model is one-twentieth scale. What velocity must the model have for dynamic similarity
Answer:
[tex]Vm=0.894m/s[/tex]
Explanation:
From the question we are told that
Velocity if travel [tex]v=4m/s[/tex]
Diameter of prototype [tex]d_1=20m[/tex] and [tex]d_2=110m[/tex]
Scale ratio=[tex]\frac{1}{20}[/tex]
Generally Velocity of of the model using Froud's model is mathematically given as
[tex]Fm=Fp[/tex]
[tex]\frac{Vm}{\sqrt{Lmg}} =\frac{Vp}{\sqrt{Lpg}}[/tex]
[tex]Vm=Vp*\frac{Vp}{\sqrt{Lpg} }[/tex]
[tex]Vm=4*\frac{1}{\sqrt{20}}[/tex]
[tex]Vm=0.894m/s[/tex]
* Psychology
Match the types of psychoactive drugs to their functions,
depressants
stimulants
amphetamines
hallucinogens
to excite neural activity and temporarily
elevate awareness
to increase dopamine activity and produce
schizophrenic-like paranoid symptoms
>
to inhibit the function of the central nervous
system and neural activity
to distort perceptions and effects on thinking
Answer:
See explanation below
Explanation:
Psychoactive drugs are drugs that affect the central nervous system. They alter cognitive function by changing mood and consciousness.
Examples;
Depressants: Inhibit the function of the central nervous system and neural activity.
Stimulants: Excite neural activity and temporarily elevate awareness.
Amphetamines: Increase dopamine activity and produce schizophrenic-like symptoms.
Hallucinogens: Distort perceptions and effects on thinking.
A drug is any substance that alters how the body functions.
What is a drug?A drug is any substance that alters how the body functions. There are different types of drugs that affect different parts of the body.
We shall now explain the following classifications of drugs;
depressants - to inhibit the function of the central nervousstimulants - elevate awarenesshallucinogens - to distort perceptions and effects on thinkingamphetamines - schizophrenic-like paranoid symptomsLearn more about drugs: https://brainly.com/question/6022349
12. A bag weighing 20 N CARRIED horizontally a distance of 35 m, How much
work is done on the bag in Joules? (Do not put units with your answer.) W=Fd *
Your answer
13. A child performs 10J of work in lifting a box 1 m in 2 seconds. How much
power did the child apply to the box? (Do not include units with your answer.)
P=W/t *
Your answer
Answer:
Explanation:
Well they told you the exact formula to use. Work is the force multiplied by the distance through which its applied.
W = (20N)(35m)
= 700 Joules
13.) Power is the amount of work done over the time through which the work is being done.
P = W/t
= 10J/2s
= 5J/s
I don’t even understand anyone help please.
Answer:
a) A:170572.5 J
C: 55794.9J
b) 170572.5 J
c) 41.4413265306m
d) 2.7455874717m/s
Explanation:
a) Kinetic energy = 0.5*m*v²
KE at A = 0.5*420*28.5² = 170572.5 J
KE at C = 0.5*420*16.3² = 55794.9 J
b) Mechanical energy is the total kinetic energy plus potential energy at a point on the system. There is no potential energy at A.
ANSWER: 170572.5 J
c) v²=u²+2as
28.5²=2(9.8)s
812.25/19.6=s
s=41.4413265306m
d) h=height from part c, r=radius of loop
v²=u²+2as
v²=gr or a=v²/r
Ei=Ef
mgh=0.5mv²+mg(2r)
gh=0.5v²+2gr
h=0.5r+2r
h=5/2r
r=2/5h=(2/5)(41.4413265306)=16.5765306122
F=ma
mg=m(v²/r)
g=v²/r
v²=(9.8)(16.5765306122)
v=√162.45
=12.7455874717m/s
An electric range has a constant current of 10 A entering the positive voltage terminal with a voltage of 110 V. The range is operated for two hours, (a) Find the charge in coulombs that passes through the range, (b) Find the power absorbed by the range, (c) If electric energy costs 12 cents per kilowatt-hour, determine the cost of operating the range for two hours.
Answer:
A. 72000 C
B. 1100 W
C. 26.4 cents.
Explanation:
From the question given above, the following data were obtained:
Current (I) = 10 A
Voltage (V) = 110 V
Time (t) = 2 h
A. Determination of the charge.
We'll begin by converting 2 h to seconds. This can be obtained as follow:
1 h = 3600 s
Therefore,
2 h = 2 h × 3600 s / 1 h
2 h = 7200 s
Thus, 2 h is equivalent to 7200 s.
Finally, we shall determine the charge. This can be obtained as follow:
Current (I) = 10 A
Time (t) = 7200 s
Charge (Q) =?
Q = It
Q = 10 × 7200
Q = 72000 C
B. Determination of the power.
Current (I) = 10 A
Voltage (V) = 110 V
Power (P) =?
P = IV
P = 10 × 110
P = 1100 W
C. Determination of the cost of operation.
We'll begin by converting 1100 W to KW. This can be obtained as follow:
1000 W = 1 KW
Therefore,
1100 W = 1100 W × 1 KW / 1000 W
1100 W = 1.1 KW
Thus, 1100 W is equivalent to 1.1 KW
Next, we shall determine the energy consumption of the range. This can be obtained as follow:
Power (P) = 1.1 KW
Time (t) = 2 h
Energy (E) =?
E = Pt
E = 1.1 × 2
E = 2.2 KWh
Finally, we shall determine the cost of operation. This can be obtained as follow:
1 KWh cost 12 cents.
Therefore, 2.2 KWh will cost = 2.2 × 12
= 26.4 cents.
Thus, the cost of operating the range for 2 h is 26.4 cents.
The pickup truck has a changing velocity because the pickup truck
A.can accelerate faster than the other two vehicles
B.is traveling in the opposite direction from the other two vehicles
C.is traveling on a curve in the road
D.needs a large amount of force to move
please get right i need awnser today
Answer:
C. Is traveling on a curve in the road
Hope this helps :3
The pick up truck has a changing velocity because, it is travelling on a curve in the road. A change in direction results in its change in velocity because, velocity is a vector quantity.
What is velocity ?Velocity is a physical quantity that measures the distance covered by an object per unit time. It is a vector quantity, thus having magnitude as well direction.
The rate of change in velocity is called acceleration of the object. Like velocity, acceleration also is a vector quantity. Thus, a change in magnitude or direction or change in both for velocity make the object to accelerate.
Here, all the three vehicles are travelling with the same velocity. But, the truck is moving to a curve on the road. The curvature in the path will make a change in its velocity.
Find more on velocity:
https://brainly.com/question/16379705
#SPJ6
The image related with this question is attached below:
When monochromatic light passes through the interface between two unknown materials at an angle θ where 0∘<θ<90∘, no changes in the direction of propagation of light are observed. What can be said about the two materials? Check all that apply. View Available Hint(s) Check all that apply. The two materials have matching indexes of refraction. The second material through which light propagates has a lower index of refraction. The second material through which light propagates has a higher index of refraction. The two materials are identical.
Answer:
the correct one is the first, the refractive index of the two materials must be the same
Explanation:
When a beam of light passes through two materials, it must comply with the law of refraction
n₁ sin θ₁ = n₂ sin θ₂
where n₁ and n₂ are the refractive indices of each medium.
In this case, it indicates that the light does not change direction, so the input and output angle of the interface must be the same,
θ₁ = θ₂ = θ
substituting
n₁ = n₂
therefore the refractive index of the two materials must be the same
When reviewing the answers, the correct one is the first
A daredevil is attempting to jump his motorcycle over a line of buses parked end to end by driving up a ramp of 64.8 degrees at a speed of 25.4 m/s. What would be the largest number of buses he can clear if the top of the takeoff ramp is at the same height as the bus tops and the buses are 10.0 m long
Answer: he can only make it over 5 buses
Explanation:
Given the data in the question;
we know that range is expressed as;
R = (V₀²sin2∅₀)/g
V₀ is the initial velocity( 25.4 m/s), ∅₀ is the angle of projection( 64.8°), g is acceleration due to gravity( 9.8 m/s²),
so we substitute
R = ((25.4)²sin2(64.8))/9.8
R = 50.7 m
now, them number of buses will be;
n = R / bus length
given that bus length is 10.0 m
we substitute
n = 50.7 m / 10.0
n = 5.07 ≈ 5
Therefore, he can only make it over 5 buses
What is displacement?
a. The distance an object travels.
b. The distance between the starting point and the ending point of an object's
journey.
C. The amount of time it takes an object to travel to a destination.
d. The path in which an object travels.
Answer:
displacement is the distance between the starting point and the ending point of an object's journey
state four law of photoelectric effect
Answer:
LAW 1 : For a given metal and frequency, the number of photoelectrons emitted is directly proportional to the intensity of the incident radiation.
---------------------------------------------
LAW 2: For a given metal, there exists a certain frequency below which the photoelectric emission does not take place. This frequency is called threshold frequency.
-----------------------------------------------
LAW 3: For a frequency greater than the threshold frequency, the kinetic energy of photoelectrons is dependent upon frequency or wavelength but not on the intensity of light.
-----------------------------------------------
LAW 4: Photoelectric emission is an instantaneous process. The time lag between incidence of radiations and emission of electron is 10^-9 seconds.
Explanation:
Answer:
LAW 1 : For a given metal and frequency, the number of photoelectrons emitted is directly proportional to the intensity of the incident radiation. ... LAW 4: Photoelectric emission is an instantaneous process.
What is average acceleration due to gravity on Earth for a 2000 kg boulder, in proper SI units?
Answer:
9.8m/s²
Explanation:
The average acceleration due to gravity on Earth for a 2000kg boulder is 9.8m/s².
Every object on earth is accelerated towards the center by a rate of change of velocity with time value of 9.8m/s².
The acceleration due to gravity on earth is a constant value from places to places.
For other planetary bodies, the value varies and it differs.
But on earth every object is accelerated at 9.8m/s².
a graduated cylinder.measures 15.3 mL. Convert this measurement to DaL
Answers:
A. 0.0153
B. 0.00153
C. 0.000153
D. 0.153
Answer:
0.000153DaL
Explanation:
We have been given:
15.3mL to convert to DaL
DaL is a unit of volume which indicates a decaliter.
This implies that;
1 Da L = 1 x 10²L
So:
1 mL = 1 x 10⁻³L
So 15.3mL will give 15.3 x 10⁻³L
So;
1 x 10²L = 1 DaL
15.3 x 10⁻³L will give [tex]\frac{15.3 x 10^{-3} }{1 x 10^{2} }[/tex] = 15.3 x 10⁻⁵DaL
Therefore, this is 0.000153DaL
Sam heaves a 16lb shot straight upward, giving it a constant upward acceleration from rest of 35 m/s^2 for 64.0 cm. He releases it 2.20m above the ground. You may ignore air resistance.
(a) What is the speed of the shot when Sam releases it?
(b) How high above the ground does it go?
(c ) How much time does he have to get out of its way before it returns to the height of the top of his head, 1.83 m above the ground?
Answer:
6.69 m/s
4.483 m
1.42s
Explanation:
Given that:
Initial Velocity, u = 0
Final velocity, v =?
Acceleration, a = 35m/s²
1.) using the relation :
v² = u² + 2as
v² = 0 + 2(35) * 64*10^-2m
v² = 70 * 0.64
v = sqrt(44.8)
v = 6.693
v = 6.69 m/s
B.) height from the ground, h0 = 2.2
How high ball went , h:
Using :
v² = u² + 2as
Upward motion, g = - ve
0 = 6.69² + 2(-9.8)*(h - 2.2)
0= 6.69² - 19.6(h - 2.2)
44.7561 + 43.12 - 19.6h = 0
19.6h = 44.7561 - 43.12
h = 87.8761 / 19.6
h = 4.483 m
C.)
vt - 0.5gt² = h - h0
6.69t - 0.5(9.8)t²
6.69t - 4.9t² = 1.83 - 2.2
-4.9t² + 6.69t + 0.37 = 0
Using the quadratic equation solver :
Taking the positive root:
1.4185 = 1.42s
On a low-friction track, a 0.66-kg cart initially going at 1.85 m/s to the right collides with a cart of unknown inertia initially going at 2.17 m/s to the left. After the collision, the 0.66-kg cart is going at 1.32 m/s to the left, and the cart of unknown inertia is going at 3.22 m/s to the right. The collision takes 0.010 s.
What is the unknown inertia?
What is the average acceleration of the heavier cart?
What is the average acceleration of the lighter cart?
Answer:
(a) the unknown inertia is 0.388 kg
(b) the average acceleration of the heavier cart is 317 m/s²
(c) the average acceleration of the lighter cart is 539 m/s²
Explanation:
Given;
mass of the first cart, m₁ = 0.66 kg
initial speed of the first cart, u₁ = 1.85 m/s
let the mass of the cart with unknown inertia be m₂
initial velocity of the second cart, u₂ = 2.17 m/s to the left
velocity of the first cart after collision, v₁ = 1.32 m/s to the left
velocity of the second cart after collision, v₂ = 3.22 m/s
time of collision, t = 0.010 s
(a) What is the unknown inertia?
Apply the principle of conservation of linear momentum, to determine the unknown inertia.
let leftward direction be negative direction
let rightward direction be positive direction
m₁u₁ + m₂u₂ = m₁v₁ + m₂v₂
0.66(1.85) + m₂(-2.17) = 0.66(-1.32) + m₂(3.22)
1.221 - 2.17m₂ = -0.8712 + 3.22m₂
1.221 + 0.8712 = 3.22m₂ + 2.17m₂
2.0922 = 5.39m₂
m₂ = 2.0922 / 5.39
m₂ = 0.388 kg
The unknown inertia is 0.388 kg
(b) the average acceleration of the heavier cart
the heavier cart has a mass of 0.66 kg
[tex]a = \frac{v_1 - u_1}{t} \\\\a = \frac{-1.32 - 1.85}{0.01} \\\\a = -317 \ m/s^2\\\\|a| = 317 \ m/s^2[/tex]
(c) the average acceleration of the lighter cart;
the lighter cart has a mass of 0.388 kg
[tex]a = \frac{v_2 - u_2}{t} \\\\a = \frac{3.22 - (-2.17)}{0.01} \\\\a =\frac{3.22 \ +\ 2.17}{0.01} \\\\a= 539\ m/s^2[/tex]
Under what conditions will a moving 0.030 kg marble and a moving 2.43 kg rock have the same kinetic energy
Answer:
To have the same kinetic energy the speed of the marble must be 9 times the speed of rock.
Explanation:
The general formula of kinetic energy is given as follows:
[tex]K.E = \frac{1}{2}mv^{2}[/tex]
where,
K.E = Kinetic Energy
m = mass of the object
v = speed of the object
So, for the marble and rock to have same kinetic energy, we can write:
[tex]K.E_{marble} = K.E_{rock}\\\\\frac{1}{2}m_{marble}v_{marble}^{2} = \frac{1}{2}m_{rock}v_{rock}^{2}\\\\(0.03\ kg)v_{marble}^{2} = (2.43\ kg)v_{rock}^{2}\\\\taking\ square\ root\ on\ both\ sides:\\v_{marble} = \sqrt{\frac{2.43\ kg}{0.03\ kg}}v_{rock}\\\\v_{marble} = 9\ v_{rock}[/tex]
Hence, to have the same kinetic energy the speed of the marble must be 9 times the speed of rock.
The tub of a washer goes into its spin-dry cycle, starting from rest and reaching an angular speed of 4.0 rev/s in 9.0 s. At this point, the person doing the laundry opens the lid, and a safety switch turns off the washer. The tub slows to rest in 15.0 s. Through how many revolutions does the tub turn during this 24 s interval
Answer:
48 rev
Explanation:
a) we can calculate the distance covered by the tube using the formula:
θ = (ω + ωo)t/2
where ω is the final angular speed, θ is the distance covered, t is the time taken, ωo is the initial angular speed.
Firstly, we calculate the distance covered from 0 to 9 s then from 9s to 24 s.
within 9s, the tub runs from rest (0) to 4 rev/s, hence:
t = 9s, wo = 0, w = 4 rev/s = (4 * 2π) rad/s = 8π rad/s. Hence:
θ = (ω + ωo)t/2 = (0 + 8π)9 / 2 = 36π rad
θ = 36π rad = (36π)/2π rev = 18 rev
Also, within 15 s, the tub runs from 4 rev/s to rest, hence:
t = 15 s, wo = 4 rev/s = 8π rad/s, w = 0 rad/s. Hence:
θ = (ω + ωo)t/2 = (8π + 0)15 / 2 = 60π rad
θ = 60π rad = (60π)/2π rev = 30 rev
Therefore the total revolutions by the tube during 24 s interval = 30 rev + 18 rev = 48 rev
A circus tightrope walker weighing 800 N is standing in the middle of a 15 meter long cable stretched between two posts. The cable was originally horizontal. The lowest point of the cable is now at his feet and is 30 cm below the horizontal. Assume the cable is massless. What is the tension in the cable
Answer:
T = 10010 N
Explanation:
To solve this problem we must use the translational equilibrium relation, let's set a reference frame
X axis
Fₓ-Fₓ = 0
Fₓ = Fₓ
whereby the horizontal components of the tension in the cable cancel
Y Axis
[tex]F_{y} + F_{y} - W =0[/tex]
2[tex]F_{y}[/tex] = W
let's use trigonometry to find the angles
tan θ = y / x
θ = tan⁻¹ (0.30 / 0.50 L)
θ = tan⁻¹ (0.30 / 0.50 15)
θ = 2.29º
the components of stress are
F_{y} = T sin θ
we substitute
2 T sin θ = W
T = W / 2sin θ
T = [tex]\frac{ 800}{ 2sin 2.29}[/tex]
T = 10010 N
As a laudably skeptical physics student, you want to test Coulomb's law. For this purpose, you set up a measurement in which a proton and an electron are situated 865 nm from each other and you study the forces that the particles exert on each other. As expected, the predictions of Coulomb's law are well confirmed. You find that the forces are attractive and the magnitude of each force is:______
Answer:
force F = 1.66 × [tex]10^{-13}[/tex] N
Explanation:
given data
proton and an electron = 865 nm
solution
we get here force that is express as
force F = k q1 q2 ÷ r² ......................1
put here value and we get
force F = 9 × [tex]10^{9}[/tex] × [tex]\frac{1.6\times (10^{-19})^{2}}{865 \times (10^{-9})^{2}}[/tex]
force F = 1.66 × [tex]10^{-13}[/tex] N
