Answer:
a magnified and erect virtual is found to be formed.
1. A 5 Ohm resistor is connected to a 9 Volt battery. How many Joules of thermal energy are produced in 7 minutes?
2. The current in a flashlight powered by 4.5 Volts is 0.5 A. What is the power delivered to the flashlight?
3. If the flashlight in the previous problem is left on for 3 minutes, how much electric energy is delivered to the bulb?
4. A 50 Ohm resistance causes a current of 5 milliamps to flow through a circuit connected to a battery. What is the power in the circuit?
5. How many Joules of electric energy are delivered to a 60 Watt lightbulb if the bulb is left on for 2.5 hours?
Answer:
Question 1: 189 joules
Question 2: 2.25 watts
Question 3: 405 joules
Question 4: 0.00125 watts
Question 5: 450000 joules
Explanation:
question 1:
Volt=1.5v
Resistance =5 ohms
Time=7 minutes
Time=7 x 60
Time=420 seconds
Current =voltage ➗ resistance
Current =1.5 ➗ 5
Current =0.3 amps
Energy=current x voltage x time
Energy=0.3 x 1.5 x 420
Energy =189 joules
Question 2:
Current =0.5 amps
Voltage =4.5v
Power=current x voltage
Power=0.5 x 4.5
Power=2.25 watts
Question 3:
Current=0.5 amps
Voltage=4.5v
Time =3 minutes
Time =3x60
Time =180 seconds
Energy=current x voltage x time
Energy=0.5 x 4.5 x 180
Energy =405 joules
Question 4:
Resistance=50 ohms
Current =5 milliamps
Current =5/1000
Current =0.005 amps
Power =current x current x resistance
Power=0.005 x 0.005 x 50
Power=0.00125 watts
Question 5:
Power =50 watts
Time=2.5 hour
Time=2.5 x 60 x 60
Time =9000 seconds
Energy=power x time
Energy=50x9000
Energy=450000 joules
1. You are playing with a jump rope that is tied at both ends. You untie one end, hold it taut and wiggle the end up and down sinusoidally with frequency 2.00Hz and amplitude 0.075m. At time t=0, the end has a maximum positive displacement and is instantaneously at rest. Assume no wave bounces back from the far end to change the pattern. What is the equation for the displacement of the wave? What is the displacement at a point 3.00m from the end .
Answer:
[tex]f(x=3.00m)=0.075mcos(\frac{2\pi(2.00Hz)}{v}(3.00m))[/tex]
Explanation:
To find the equation of the wave you use the general equation for a wave, given by:
[tex]f(x)=Acos(k x-\omega t)[/tex]
A: amplitude of the wave = 0.075m
k: wave number
you select a cosine function because for x=0 and t= 0 you get a maximum displacement.
To find the displacement of the wave for x=0 you can consider that the form of the wave is independent of time t.
Then, you calculate k:
[tex]k=\frac{\omega}{v}=\frac{2\pi f}{v}[/tex]
Thus, you need the value of the speed of the wave (you only have the frequency f), in order to calculate f(x), for x=3.00m:
[tex]f(x=3.00m)=0.075mcos(\frac{2\pi(2.00Hz)}{v}(3.00m))[/tex]
Although science strives for objectivity by basing conclusions and explanations on data gathered during scientific investigations,
some subjectivity still exists in science, since it is a human endeavor. What beneficial qualities exist in scientific processes,
methods, and knowledge as a result of science being a human endeavor?
A. bias and favoritism
B.
creativity and discovery
C. inaccuracies and errors
D.
all of these
Answer: creativity and discovery
Explanation: i got it right on study island .
Answer:
CREATIVITY AND DISCOVERY
Explanation:
STUDY ISLAND
Two pulleys, one with a radius 2R and one with a radius of R, are welded together and can rotate about the same axis. A block is suspended from a string that is wrapped around the small disk and unwinds without slipping as the block descends a distance H and reaches a certain final speed. If the string with the block at the other end were wrapped around the larger disk, how would the final speed of the block change?
Answer:
speed will double
Explanation:
Tangential velocity is given by
v=wr
where r is radius and w is rotational velocity. When r is increased to 2R, keeping roational velocity constant, the tangential velocity doubles. Hence unwinding will take place at a twice the rate and the final velocity will be double
A possible means for making an airplane invisible to radar is to coat the plane with an antireflective polymer. If radar waves have a wavelength of 2.92 cm and the index of refraction of the polymer is n = 1.30, how thick (in cm) would you make the coating? (Assume that the index of refraction of the plane is higher than that of the coating. Also assume that the radar waves are normal to the surface of the coating. Give the minimum thickness that would make the airplane invisible to radar.)
Answer:
The thickness is [tex]t = 0.5615 \ cm[/tex]
Explanation:
From the question we are told that
The wavelength of the of the rader waves is [tex]\lambda = 2.92 \ cm[/tex]
The index of refraction of the polymer is [tex]n = 1.30[/tex]
The thickness is mathematically represented as
[tex]t = \frac{\lambda }{4 n }[/tex]
Substituting values
[tex]t = \frac{2.92}{4 * 1.30 }[/tex]
[tex]t = 0.5615 \ cm[/tex]
A 50 Ohm resistance causes a current of 5 milliamps to flow through a circuit connected to a battery. What is the power in the circuit?
Answer:0.00125 watts
Explanation:
resistance=50 ohms
Current=5 milliamps
Current=5/1000 amps
Current=0.005 amps
Power=(current)^2 x (resistance)
Power=(0.005)^2 x 50
Power=0.000025 x 50
Power=0.00125 watts
Answer:
if a circuit is powered by 100v and has an overall resistance of 50 ohms 2 amps flows through the circuit
Explanation:
Which of the following BEST summarizes the relationship between groups and culture and critical thinking?
Answer:
Groups and culture helps in influencing our values,ethics and beliefs. This influence should always be questioned through the process of thinking critically.
This best summarizes the relationship between groups and culture and critical thinking.
Which of the following characteristics of Earth's crust is likely to contribute to geological events?
A. can be broken into many plates
B. has has uniform thickness throughout
C. cysts on top of the solid rock of the lower mantle
D. is composed of a single layer that surrounds Earth
Answer:A
Explanation:
The crust Of The earth's has plates boundaries,when the layers that forms to boundaries glide on each other, vibrations occur which are known as earthquakes
Answer:
A) Can be Broken Into Many Plates
plzzz help will mark the brainliest
During an earthquake, _______ travels through the Earth's interior as _______ waves.
Answer:
During an earthquake, seismic waves travels through the Earth's interior as body or p waves.
Explanation:
If neither of the bold words look familiar from your lesson feel free to ignore this answer
In this circuit the battery provides 3 V, the resistance R1 is 7 Ω, and R2 is 5 Ω. What is the current through resistor R2? Give your answer in units of Amps. An Amp is 1 Coulomb of charge flowing through a cross-sectional area of the wire per second - that's a lot of charge per second and will warm up a typical wire quite a bit! Most devices have circuits with larger resistors - kLaTeX: \OmegaΩ (103 LaTeX: \OmegaΩ) and MLaTeX: \OmegaΩ (106 LaTeX: \OmegaΩ) are common.
Answer:
The current pass the [tex]R_2[/tex] is [tex]I = 0.25 A[/tex]
Explanation:
The diagram for this question is shown on the first uploaded image
From the question we are told that
The voltage is [tex]V = 3V[/tex]
The first resistance is [tex]R_1 = 7 \Omega[/tex]
The second resistance is [tex]R_2 = 5 \Omega[/tex]
Since the resistors are connected in series their equivalent resistance is
[tex]R_{eq} = R_1 +R_2[/tex]
Substituting values
[tex]R_{eq} = 7 + 5[/tex]
[tex]R_{eq} = 12 \Omega[/tex]
Since the resistance are connected in serie the current passing through the circuit is the same current passing through [tex]R_2[/tex] which is mathematically evaluated as
[tex]I = \frac{V}{R_{eq}}[/tex]
Substituting values
[tex]I = \frac{3}{12}[/tex]
[tex]I = 0.25 A[/tex]
What is an independent variable?
A. A variable that is intentionally changed during an experiment
B. A variable that depends on the experimental variable
C. A variable that is not used in an experiment
D. A variable that is unknown during the experiment
Answer:
The answer is A
Explanation:
Independent variables don't have to depend on other factors of the experiment because they're independent
Answer:
A.
Explanation:
Independent variables don't have to depend on other factors of the experiment because they're independent.
Q8.(10 points) a)When you cough,the radius of your trachea (windpipe) decreases,affecting the speed of the air in the trachea. If 0 r is the normal radius of the trachea, the relationship between the speed S of the air and the radius r of the trachea during a cough is given by a function of the form 2 0 S r ar r r ( ) ( ) = − , where a is positive constant. Find the radius r for which the speed of the air is greatest
Answer:
[tex]\bf{r=\frac{2r_o}{3}}[/tex] is greatest
Explanation:
Given:
[tex]S(r)=ar^2(r_{o}-r)[/tex]
[tex]\frac{ds}{dr}=2ar(r_{o}-r)+ar^2(-1)[/tex]
[tex]\frac{ds}{dr}=2ar_{o}-2ar^2-ar^2[/tex]
[tex]\frac{ds}{dr}=2ar_{o}-3ar^2[/tex]
Substitute [tex]\frac{ds}{dr} = 0[/tex], so
[tex]2ar_{o}-3ar^2=0[/tex]
Then, get the common value from the equation.
[tex]ra(2r_{o}-3r) = 0[/tex]
[tex]\bf{r=0}\\r=\frac{2r_{o}}{3}[/tex]
[tex](\frac{d^2s}{dr^2})_{r=0}=2ar_{o}-6ar[/tex]
[tex](\frac{d^2s}{dr^2})_{r=0}=2ar_{o} >0\;and, \\(\frac{d^2s}{dr^2})_{r}=\frac{2r_o}{3} <0[/tex]
So, the speed of the air is greatest.
[tex]\bf{r=\frac{2r_o}{3}}\;is\;greatest[/tex]
During the process of mountain building, earthquakes sometimes occur along continental-continental convergent boundaries. Which statement best describes the motion of the plates along these boundaries that causes the earthquakes?
The plates push apart from each other with no subduction.
Subduction occurs with the less-dense plate sinking below the other plate.
Subduction occurs with the more-dense plate sinking below the other plate.
The plates smash together with no subduction.
Answer:
The correct answer is The plates smash together with no subduction. I just took this on Edge. Glad I could help!
The statement best describes the motion of the plates along these boundaries that causes the earthquakes is that The plates smash together with no subduction
For better understanding let's explain what the answer means
it is said that the meeting point of two tectonic plates will causea convergent plate boundary to be formed. one of the converging plates will move under the other as it is known as subductionFrom the above we can therefore say that the answer The statement best describes the motion of the plates along these boundaries that causes the earthquakes is that The plates smash together with no subduction, is correct
Learn more motion of the plates along these boundaries from:
https://brainly.com/question/23731885
I need some help!!!!!!!!!
Answer:
The Object will immediately begin moving toward the left
Explanation:
Because the force of thirteen is greater than ten and applied to the opposite side
A large boulder falls from an underwater ledge and crashes on the floor of the ocean. A pod of dolphins is 800 meters away. Determine how long it takes for the sound of the crash to reach the dolphins.
0.5 sec
0.3 sec
2.3 sec
1.9 sec
Answer:
0.5
Explanation:
Answer:
0.539
Explanation:
An athlete is working out in the weight room. He steadily holds 50 kilograms above his head for 10 seconds. Which statement is true about this situation?
Answer:
Answer: the true statement form the given statements is “the athletes is not doing any work because he does not move weight”
Explanation:
The athlete isn’t doing any work because he doesn’t move the weight is the correct statement.
What is Work? Work is the energy transferred to or from an object via the application of force along a displacement.Work = Force x Displacement.How to solve this Problem?The weight of an object given is 50kgsThe time of holding an object given is 10 secondsWe need to justify the statements
Here ,
There is no displacement that means displacement is zero.If displacement is zero then work done will also be zeroHence there is no work done by the athlete
Therefore ,The athlete isn’t doing any work because he doesn’t move the weight is the correct statement
Learn more about Work done here
https://brainly.com/question/25573309
#SPJ2
Is mercury (the planet) rocky or gaseous(meaning relating to or having the characteristics of a gas.)
Answer:
Mercury is rocky
Explanation:
Answer:
Rocky
Explanation:
It has no atmosphere so it cannot hold gas.
Air is matter which backs best support the statement
Answer: A. Balloons can be filled with air.
C. Air has mass.
Explanation:
Learn more https://brainly.com/question/3238218
Balloons are able to be filled with air and air has mass.
You are designing an optical fiber scope for directing light into a confined area. You want to keep light within the fiber. Based on the specifications, you know that the greatest angle that the light will make with the horizontal is no greater than 25⁰. Assuming you will be using the scope in the body which has the same index of refraction of water (n = 1.33). What is the minimum index of refraction n2 required for the design to be functional?
Answer:
Explanation:
For entry of light into tube of unknown refractive index
sin ( 90 - 25 ) / sinr = μ , μ is the refractive index of the tube , r is angle of refraction in the medium of tube
r = 90 - C where C is critical angle between μ and body medium in which tube will be inserted.
sin ( 90 - 25 ) / sin( 90 - C) = μ
sin65 / cos C = μ
sinC = 1.33 / μ , where 1.33 is the refractive index of body liquid.
From these equations
sin65 / cos C = 1.33 / sinC
TanC = 1.33 / sin65
TanC = 1.33 / .9063
TanC = 1.4675
C= 56°
sinC = 1.33 / μ
μ = 1.33 / sinC
= 1.33 / sin56
= 1.33 / .829
μ = 1.6 Ans
Describe at least two different objects that you think are magnetic and why do you think this objects are magnetic
Answer:
Magnetic letters Screws and bolts
Explanation:Magnetic letters have to be magnetic so they can stick to things like walls and fridges. Screws and bolts are magnetic becaus they become easier to to screw onto things since the tool that you use to screw it in is also magnetic.
Answer:
File cabins and nails/screw,
Explanation:
Because they are ferromagnetic this means that they can be magnetized. Magnetic objects are made of metal and metals do attract magnet.
a girl pushes an 18.15 kg wagon with a force of 3.63 N. what is the acceleration?
A. 0.06 m/s2
B. 5 m/s2
C. 0.2 m/s2
Answer:0.2 m/s^2
Explanation:
mass=18.15kg
Force=3.63N
Acceleration=force ➗ mass
Acceleration=3.63 ➗ 18.15
Acceleration=0.2 m/s^2
A girl pushes a wagon of mass 18.15 kg with a force of 3.63 N, so the acceleration of the wagon will be 0.2 m/s².
What is acceleration?In mechanics, acceleration is the measure of how rapidly an object's velocity changes over time. Accelerations as a vector quantity. An object's acceleration depends on the direction of the net force exerted on it.
A vector quantity, acceleration, is something that has both a magnitude and a direction. As a vector quantity, velocity is also. The ratio of the velocity vector change over a time interval to that interval is the definition of acceleration.
Mass, m =18.15 kg
Force, f = 3.63 N
Force = m × a
a= f / m
a =3.63 / 18.15
a = 0.2 m/s²
Hence, the acceleration of the wagon will be 0.2 m/s².
To get more information about acceleration :
https://brainly.com/question/12550364
#SPJ2
Mutations that neither benefit nor harm the organisms have blanks effect on the organisms survival
Answer:
I would say that the mutation has no effect on the organism, as it doesn't help or harm it.
hope this helps :)
During last year’s diving competition, the divers always pull their
limbs in and curl up their bodies when they do flips. Just before
entering the water, they fully extend their limbs to enter straight down
as shown.
Explain the effect of both actions on their angular velocities and
kinetic energy (support your answer with working). Also explain the
effect on their angular momentum.
Answer:
The divers pull in their limbs and curl up their bodies because doing so decreases their moment of inertia and increases their angular velocity
Explanation:
The conservation of angular momentum states that in a rotational system, the initial angular momentum is equal to the final angular momentum if no torque acts on it.
Angular momentum is equal to the product of the moment of inertia about its axis and the angular velocity
Angular momentum = Iω[tex]\\[/tex]
where I = moment of inertial = mass x [tex]radius^{2}[/tex]
I = m[tex]r^{2}[/tex]
angular momentum = m[tex]r^{2}[/tex]ω
since angular momentum is constant, one can see that decreasing the radius of rotation about the body by curling in the limb will cause the moment of inertia to decrease and the angular velocity to increase.
NB: mass of the body is constant.
A pipe branches symmetrically into two legs of length L, and the whole system rotates with angular speed ω around its axis of symmetry. Each branch is inclined at angle α to the axis of rotation. Liquid enters the pipe steadily, with zero angular momentum, at volume flow rate Q. The pipe diameter, D, is much smaller than L. Obtain an expression for the external torque required to turn the pipe. What additional torque would be required to impart angular acceleration ω_ ?
Answer:
Check the explanation
Explanation:
Kindly check the attached images below to see the step by step explanation to the question above.
What happens if you move a magnet near a could of wire
Answer:
The wire would stick to the magnet????????????????????????
Explanation:
A 50 Ohm resistance causes a current of 5 milliamps to flow through a circuit connected to a battery. What is the power in the circuit?
Answer:0.00125 watts
Explanation:
resistance=50 ohms
Current=5 milliamps
Current=5/1000 milliamps
Current =0.005 amps
power=(current)^2 x (resistance)
Power=(0.005)^2 x 50
Power=0.005 x 0.005 x 50
Power=0.00125 watts
The power in the circuit is 1.25 mW.
What is Ohm's law?
Ohm's law states that the current through a conductor between two points is directly proportional to the voltage across the two points, provided the temperature and other physical conditions remain constant.
In other words, the current (I) in a circuit is equal to the voltage (V) divided by the resistance (R):
I = V/R.
This relationship is often written as V = IR or R = V/I. Ohm's law is named after Georg Simon Ohm, a German physicist who first formulated the relationship in the early 19th century.
Here in the Question,
Using Ohm's law, we can find the voltage in the circuit as:
V = IR
V = (5 mA)(50 Ω) = 0.25 V
Using the formula for power, we can find the power in the circuit as:
P = IV
P = (5 mA)(0.25 V) = 0.00125 W or 1.25 mW
Therefore, the power in the circuit is 1.25 mW.
To learn more about Coulomb's law click:
brainly.com/question/28040775
#SPJ3
A brick is dropped from a high scaffold. a. What is its velocity after 4.0s ?
b. How far does the brick fall during this time ?
Answer:
A: 1.962
B: 3.924
Explanation:
g = G *M /R^2
g = 9.807*M/R^2 the gravitational constant of ground level on earth is about 9.807
g = 9.807*5lbs/R^2 the average brick is about 5 pounds.
g = 9.807*5*10^2. I'm assuming the height is around ten feet to help you out.
with these numbers plugged in you get an acceleration of 0.4905 a final velocity after 4 seconds 1.962. It's height fallen after 4 seconds is 3.924.
( M = whatever the brick weighs it's not specified in the question)
(R = the distance from the ground or how high the scaffold is)
(hopefully you can just plug your numbers in there hope this helps)
In this experiment, you need to examine the idea of thermal energy transfer. Using a controlled experiment, what might a good question about the variables that affect thermal energy transfer be? Thermal energy transfer depends on many properties, but limit your question to only two.
Answer:
We shall consider two properties:
1. Temperature difference
2. Thermal conductivity of the material
Use a cylindrical rod of a given material (say steel) which is insulated around its circumference.
One end of the rod is dipped in a large reservoir of water at 100 deg.C and the other end is dipped in water (with known volume) at 40 deg. C. The cold water if stored in a cylinder which is insulated on all sides. A thermometer reads the temperature of the cold water as a function of time.
This experiment will show that
(a) heat flows from a region of high temperature to a region of lower temperature.
(b) The thermal energy of a body increases when heat is added to it, and its temperature will rise.
(c) The thermal conductivity of water determines how quickly its temperature will rise. If mercury replaces water in the cold cylinder, its temperature will rise at a different rate because its thermal conductivity is different.
Explanation:
An electromagnet requires 3 things. Select the 3 components below.
A. battery
B. iron core
C. solenoid
D. heat
E. insulator
F. resistance
Answer:
A. Battery
B. Iron Core
C. Solenoid
