Answer:
a) Pascal is a derived unit because it is derived from the unit of force and area
b)Mass is a fundamental quantity because it doesn't depends upon others physical quantity and made up of only one unit
c) unit of power is a derived unit because they are dependent quantities
D) unit of length is a fundamental unit because it cannot be expressed in terms of another quantity.
Which nucleus completes the following equation?
Please ignore the answer I chose, it might be wrong
Answer:
D. [tex]^{39}_{18} Ar[/tex]
Explanation:
The given nuclear equation is the beta decay of chorine in which an electron, known as a beta particle, is given off from within the nucleus due to the breakdown of a neutron within the nucleus into a proton and a beta particle, such that the atomic number is increased by 1 from 17 to 18, which is the atomic number or argon, Ar, as follows;
[tex]^{39}_{17}Cl \ \rightarrow \ ^0_{-1} e + \ ^{39}_{18} Ar[/tex]
A car generator turns at 400 rpm (revolutions per minute) when the engine is idling. It has a rectangular coil with 300 turns of dimensions 5.00 cm by 6.46 cm that rotates in an adjustable magnetic field. What is the field strength needed to produce a 24.0 V peak emf
Answer:
The field strength needed to produce a 24.0 V peak emf is 0.5913 T
Explanation:
From the formula for maximum emf of a generator,
[tex]emf_{max}= NAB\omega[/tex]
∴ [tex]B = \frac{emf_{max} }{NA\omega}[/tex]
Where N is the number of loops
A is cross section of loops
B is magnetic field strength
ω is the angular frequency of loops
From the question, [tex]emf_{max} = 24.0V[/tex]
N = 300 turns
A = l × b ( since it is a rectangular coil)
A = 6.46 cm × 5.00 cm
A = 0.0646 m × 0.05 m
A = 0.00323 m²
ω = 400 rpm = (400/60)×2π rad/s
ω = 41.8879 rad/s
Putting all the parameters into the formula
[tex]B = \frac{emf_{max} }{NA\omega}[/tex]
[tex]B = \frac{24.0}{300\times0.00323\times41.8879}[/tex]
[tex]B = 0.5913T[/tex]
Hence, the field strength needed to produce a 24.0 V peak emf is 0.5913 T
Non-ideal behavior for a gas is most likely to be observed under conditions of a) high pressure and low temperature. b) high temperature and high pressure. c) high temperature and low pressure. d) standard temperature and pressure. e) low temperature and low pressure.
Answer:
high temperature and low pressure
Explanation:
Real gases have intermolecular forces of attraction between them hence they can be liquified. However, gases approach ideal behavior at high temperature and low pressure.
According to the kinetic theory of gases, gases molecules move at incredibly high speeds and exhibit no intermolecular interaction because the gas molecules are isolated from each other.
At high temperature and low pressure, gas molecules are found to possess maximum kinetic energy. They move with a very high velocity and have minimal intermolecular interaction between them in accordance with the proposition of the kinetic theory of gases.
Which type of wires (copper, aluminum, or string) are ferromagnetic metals?
Answer:
Copper isn't ferromagnetic,
Aluminum isn't ferromagnetic,
String has a ferromagnetic property
So in conclusion:
The answer is strings :)
The direction of applied force has to be .............. to the distance in order to say work is done
Answer:
Parallel
Explanation:
The work done is defined as the force applied on an object and the displacement in the position of the object in the direction of force.
W = F s cos A
where, F is the force, s is the displacement and A is the angle between force and displacement.
When the angle between the force and the displacement is 90 degree, the work done is zero.
To get the maximum work the angle between the force and the displacement is 0 degree.
So, to get the work done by the force the angle between the force and displacement is 0 degree that means the force and displacement is parallel to each other.
A merry-go-round rotates with a centripetal acceleration of 18 m/s^2. If the outer horses are 9 m from the center of the ride. What is their velocity?
A. 12.7 m/s
B. 14.6 m/s
C. 16.3 m/s
D. 10.4 m/s
Answer:
A
Explanation:
a_c = v^2/r
v = sqrt*a_c × r*
v = sqrt * 18 × 9*
v = 9×sqrt *2*
v = 12. 7 m/s
Annie has a soccer ball and a cake ball she kicks each ball with the same Force the soccer ball accelerates at 3 m per second squared and the kickball accelerates at 5 m per second squared use Newton's law to describe why the kickball has a greater acceleration
Which of the following is a contact force?
A. applied
B. electromagnetic
C. nuclear
D. gravity
applied force is a contact force
Is velocity ratio of a machine affected by applying oil on it? Explain with reasons.
Answer:
when it comes to machines being Rusty oil is like the root loosener
why does balloon pop in the sun?
Answer:
The heat gives atoms/ particles in balloon more kinetic energy so they move further apart, increasing size and eventually popping balloon
^ very simple explanation
Explanation:
5. Which one of the following factors is directly proportional to density of liquid? (a) Temperature (b) Volume of liquid (c) Upthrust (d) Density of object
Answer:
A
The upthrust on a floating body is in upwards direction and is equal to the weight of the liquid displaced
B
The upthrust is directly proportional to the density of the liquid in which the solid is immersed
C
The upthrust is directly proportional to the volume of the fluid displaced by a solid
The upthrust acts on the body in upward direction at the center of buoyancy.
Upthrust is equal to the weight of liquid displaced by object and weight of liquid will depend on its density.
Upthrust is F=Vρg ,where V is the volume of liquid displaced and ρ is the density of fluid.
The total lateral pressure acting on an immersed object on one side is equal and in opposite direction to the total lateral pressure acting on the other side.
D=12000 m
T= 30min
V=?
Ayudenme en este ejercicio xfa
En m/min y en Km/h
Our Moon a. was a separate small planet before it was captured by the Earth's gravity. b. spun off the fast-spinning Earth during the early formation of the Solar System. c. coalesced from gas and dust in its current place next to the Earth. d. was formed by the collision of the Earth with a Mars-sized protoplanet.
Answer:
d. was formed by the collision of the Earth with a Mars-sized protoplanet.
According to the The giant-impact hypothesis the Moon was formed from the debris of a collision between the Earth and a Mars-sized protoplanet.
is there any machine that is 100% efficient? why?why not
Answer:
No, it's not there.
Explanation:
For a machine to be 100% efficient, it has to be with an output which is equal to its input. But machines have an out put less than an input, hence efficiency below 100%.
the atomic number of phosphorus is
Answer:
The atomic number of phosphorus is 15.
Explanation:
It’s found after Si(Silicon) and before S(sulphur)
1. explain the procedure undertaken if you have to measure the density of the contents of a milk carton. 2. two objects have the same mass. How about the density of the two objects?
To calculate the density of a substance, its mass and volume has to be determined. So that:
i. For the milk in the carton, its mass and volume should be known.
ii. For the two objects given in the question, their individual masses and volumes have to be determined.
Density of a substance (ρ) is the rate of the mass (m) of the substance to its volume (V). It is measure in kg/[tex]m^{3}[/tex].
i.e ρ = [tex]\frac{m}{V}[/tex]
The density of a substance can be determined once the mass and its volume have been accurately measured.
1. How to measure the density of the contents of a milk carton.
a. Determine the mass of the milk carton with its content.
b. Determine the mass of the milk carton when empty.
c. Subtract the mass of the milk carton when empty from the mass of the carton with its content. This will give the mass of the milk in the carton.
d. Using a beaker, measure the volume of the milk.
e. Divide the mass of the milk by its volume to determine its density.
2. How to measure the densities of two objects of equal mass.
a. Fill an Eureka's can or a beaker with sprout with water to its brim.
b. Slowly drop the mass into the beaker with water so as to collect the volume of the liquid displaced into another beaker.
c. The volume of the liquid displaced is the volume of the mass.
d. Divide the mass of the object by its volume to determine its density.
NB: These procedures are observed to determine the densities of the two object individually.
For more explanations, visit: https://brainly.com/question/17924956
A stone is thrown into a pond. Five waves were made from the same source in 10 seconds.
The frequency of the wave for the stone thrown in the pond is 0.5Hertz.
The question does not specify what to calculate but we can look for the frequency of the wave.
Frequency is the number of oscillations completed in one second. This is interpreted as:
x oscillations = 1second
If Five waves were made from the same source in 10 seconds for a stone that is thrown inside the pond, then:
5 oscillations = 10seconds
Divide both expressions to get x (the required frequency)
x/5 =1/10
Cross multiply
10x = 5
Divide both sides by 10
10x/10 = 5/10
x = 1/2
x = 0.5Hertz
Hence the frequency of the wave is 0.5Hertz.
NB: The period of the wave is simply the reciprocal of the frequency.
Learn more here: https://brainly.com/question/13728731
An empty cardboard box falls from a high platform. Through the use of special equipment it was found that the energy of the cardboard box at the top of the fall was more than the energy of the box at the bottom of the fall. Explain.
Answer:
The mechanical energy of the cardboard box, M.E. = K.E. + P.E.
Where;
P.E. = The potential energy of the cardboard box = m·g·h
K.E. = The kinetic energy of the cardboard box = (1/2)·m·v²
Where;
m = Mass of the cardboard box
g = The (constant) acceleration due to gravity ≈ 9.81 m/s²
h = The height of the cardboard box
v = The velocity of the cardboard box
At the top of the fall, where h = The height of the platform = [tex]h_{platform}[/tex], and v = 0 (the box is initially at rest at the top), the M.E. is given as follows;
[tex]M.E._{top}[/tex] = P.E. + K.E. = m·g·[tex]h_{platform}[/tex] + (1/2) × m × 0² = m·g·[tex]h_{platform}[/tex]
However, at the bottom of the fall, the height of the box, h = 0, the velocity of the box, v = 0, therefore, the total energy at the bottom, after the box comes to rest, [tex]M.E._{bottom}[/tex] = 0
Therefore;
The total energy of the box at the top of the fall, .[tex]M.E._{top}[/tex] = m·g·[tex]h_{platform}[/tex] was more than the total energy of the box at the bottom of the fall,
[tex]M.E._{bottom}[/tex] = 0
Explanation:
A bike travels at 3.0 m/s, and then accelerates to a speed of
8.5 m/s in a time of 2.5 seconds. The average acceleration of
the bike is
m/s2
The average acceleration of the bike is 2.2 m/s²
What is average acceleration?Acceleration, rate at which velocity changes with time, in terms of both speed and direction.
A point or an object moving in a straight line is accelerated if it speeds up or slows down.
According to the question,
Given, initial velocity, u=3.0m/s and final velocity v=8.5 m/s
Time = 2.5 seconds
If a be the acceleration.
a = [tex]\frac{v-u}{t}[/tex]
a = [tex]\frac{8.5 - 3.0}{2.5s}[/tex]
⟹ a=2.2 m/s²
So, The average acceleration of the bike is 2.2 m/s²
Learn more about average acceleration here:
https://brainly.com/question/2303856
#SPJ2
The mass of earth 6*10^24kg and radius is 400kg Now find the value of acceleration due to gravity when a object is 3600km from the earth surface
the force between the earth and the body which is at a distance r from the center of the earth is F. What must be this distance for the force to be doubled.
Answer:
Explanation:
The gravitational force between the earth and another body is F = -GM_em/r^2 r where G = 6.67 times 10^-11 Nm^2/kg^2 is the gravitational constant, M_e = 5.97 times 10^24 kg is the mass of the earth, m is the mass of the other body, and r is the position vector of the second body with respect to the centre of the earth.
difference between uniform motion and non uniform motion
Answer:
Uniform motion is a type of motion that is characterized as the motion of an object wherein the object moves in a straight line and its velocity remains unchanged along that line, regardless of the duration of time, as it occupies equal distances at equal time interval and Non-uniform motion is described as the motion of an object wherein the object moves at different speeds and does not cover the same distance at equal time intervals, regardless of the duration of the time interval.
Answer:
hope it's help you
Explanation:
In Uniform motion, the movement of a body is along the straight line with constant speed. In non uniform motion, the movement of a body is along the straight line with variable speed. In uniform motion, the body covers equal distance in an equal interval of time.
What is meant by the term wave front?
Explanation:
Wave front, imaginary surface representing corresponding points of a wave that vibrate in unison. ... Wave fronts for longitudinal and transverse waves may be surfaces of any configuration depending on the source, the medium, and the obstructions encountered.
The force exerted by the earth on a body is called ______of a body.
Answer:
The force exerted by the earth on a body is called gravitational of a body.
i think this is the answer
Answer:weight
Explanation:
why does a stone sink and a ship float
Answer:
A stone is more dense than water and the air in draft of the boat is less dense than water.
What is not one of the main uses of springs?
A. Bike suspension
B. The seasons
C. Clock making
D. Car suspension
Quick answer
Answer:
b. the seasons
Explanation:
Density of an object can be found by calculating mass divided by volume. If two objects have the same mass, but one has a greater volume, the object with more volume is less dense. Does water’s density change when it is frozen?
Answer:
yes, the density of ice is less than the density of water. Ice floats on water.
Explanation:
# Astronaut fells weightlessness in a spacecraft why?
Answer:
......... ........ ... .... .... . .. .......
.....
Explanation:
........mmmmmmmmmmm
What kind of circuit is the one shown below?
A. Series
B. Parallel
C. Open
D. Combination
That's a parallel circuit. (B)
When current from Point-A reaches the 3-way intersection just to the right of Point-B, it has to make a choice: Either turn left, go through B, and light the lower bulb, or go straight and light the upper bulb.
A circuit that has any "decision" points in it is a parallel circuit. What happens in the real world is: The current splits up. Some of the current that reaches the intersection turns left toward Point-B, and the rest of it goes straight up.
A series circuit is one in which there's only one possible path all the way around. There are no intersections of more than 2 roads, and no electron ever has to decide which way to flow.
An open circuit is one in which there's a break somewhere along the line and electrons can't jump across it. It's like a railroad where a big piece is cut out of the track somewhere. So no trains can travel on that route, and there's no current flowing anywhere in the circuit.
I'm not so sure about a "combination" circuit. I guess you could give that name to a complicated circuit that has some series parts and some parallel-parts. Personally, I'd call that a "series-parallel" circuit. But it really doesn't matter right now. Whatever the word means, the circuit in the picture is definitely not a "combination" circuit.
Answer:
B. Parallel Circuits
Explanation:
A parallel circuit is constructed by connecting the terminals of all the individual load devices so that the same value of voltage appears across each component. In a parallel circuit, charge divides up into separate branches such that there can be more current in one branch than there is in another.
hope i helped
differniate between Magnetic force and electrostatic force
Answer:
magnetic force:
i) It is exerted by a magnet.
ii)Magnetic forces are always normal to the direction of the velocity of the charge it acts upon.
Electrostatic force
i) It is exerted by electrically charged body.
ii)Electric force are independent of the direction the charge moves in.
✌✌✌✌
