Find the current ix in the circuit below using phasors and NODAL ANALYSIS. Note that the current source is a dependent source.
Answers
The current ix in the circuit using phasor and NODAL ANALYSIS is 7.69cps(4t+108.4⁰)A
How to determine the current?We should know that current involves the flow of electric charge.
The process is that the circuit must be converted to frequency domain.
This is to say that
20cos + 4t=20/0⁰ where w= 4 rad/s
The given parameters are
1H=lwl=j4
0.5H=jwl-j2
0.1F=1/jwl=j2.5
Now, the domain equivalent of the frequency is
20-V₁/10=V/j1.5+V₁-v/j4Taking the second node we have
2lₓ+V₁-V₂/j4=V₁/j2
On the other hand, L₁+V₁-V₂/j4=V₁/j2
At this point we have to simplify the expression to get
11V₁+15V₂=0 ............................(1)
This can be put into matrix form to get
[tex]\left[\begin{array}{ccc}1+j1.5&j2.5\\11&15\\\end{array}\right] \left[\begin{array}{ccc}V_{1} \\\\V_{2} \end{array}\right] =\left[\begin{array}{ccc}20\\\\0\end{array}\right][/tex]
Solve for the determinant
Δ[tex]\left[\begin{array}{ccc}1+j1.5&j2.5\\\\11&15\end{array}\right][/tex]= 15-j5
This implies that
Δ₁=[tex]\left[\begin{array}{ccc}1+j1.5&12.5\\\\0 &1.5\end{array}\right] =20[/tex]
Simplifying the expression to get
l₂=V₁/j2.5=18.97/18.73÷2.5/90=7.59/108.4⁰A
Therefore, when this is transformed we have
i₂=7.59cos(4t+108.7⁰)A
Learn more bout NODAL ANALYSIS on https://brainly.com/question/26099417
#SPJ1
Related Questions
Consider the following method. public static void addOneToEverything(int[] numbers) { for (int j = 0; j < numbers.length; j++) { numbers[j]++; } } Which of the following code segments, if any, can be used to replace the body of the method so that numbers will contain the same values? I. for (int num : numbers) { num++; } II. for (int num : numbers) { num[j]++; } III. for (int num : numbers) { numbers[num]++; } A I only B I and III only C II and III only D I, II, and III E None of the code segments will return an equivalent result. E None of the code segments will return an equivalent result
Answers
The code segments, if any, can be used to replace the body of the method so that numbers will contain the same values is E None of the code segments will return an equivalent result
What is an array?Using an entire set of values at once is possible with array programming, a technique used in computer science. These answers are frequently applied in scientific and engineering contexts. A data structure called an array consists of a set of elements (values or variables), each of which is identified by an array index or key.
Depending on the language, other data types that describe aggregates of values, like lists and strings, may overlap (or be identified with) array types. An array is a grouping of identically-typed elements that are stored in consecutive memory locations and can each be individually referred to using an index to a special identifier.
Based on the information, it should be noted that none of the code will return the same result as all the codes does not assign correct values to array.
Therefore, based on the information, the correct option is E.
Learn more about array on:
https://brainly.com/question/19634243
#SPJ1
you are using the vi editor to manage a text file on a linux system. you want to type new text into the file. when you type, you want the existing text that comes after the cursor to be pushed down.
Answers
The insert mode is used to type new text into the file in linux system.
What is insert mode in linux system?When inserting text into a file, you should be in insert mode. Command mode is the mode to be in when issuing commands such as moving the cursor, deleting text, copying and pasting, saving the file, and so on. Vi is in command mode when you open a file. Insert mode is required to enter text.In Insert mode, you can enter text, use the Enter key to move to a new line, navigate text with the arrow keys, and use vi as a free-form text editor. Press the Esc key once to return to Command mode.In vi, there are three modes of operation:
Mode of Command: When you launch vi, it is in Command Mode.Insert mode: You can insert text into the file using this mode.Last Line Mode (Escape Mode): While in Command Mode, type a colon [:] to enter Line Mode.The complete question:
"You're using the vi editor to manage a text file on a Linux system. You want to type new text into the file; when you type you want the existing text that comes after the cursor to be pushed down?
What mode do you need to be in to do this?"
To learn more about insert mode refer to :
https://brainly.com/question/29757726
#SPJ4
write a python program to print the following shape using your first name characters: ex: my first name is ali, and the output has to be: ALLIII
Answers
# Provide a static input for the word and store it in a variable. putword = givenword ("Enter your name:") # Create a variable named "sampstrng" and store an empty string in it. SampleString = " # Use a for loop to iterate through the given word(string). if givenword has this wordchar: # Use string concatenation to join the iterator character to the sampstrng. wordchar = sampstrng + sampstrng.Print out the sample string. print.
Anything that repeatedly performs the same actions is said to be in a loop or to be operating on a loop: The cassette was in a continuous loop, playing the same tunes over and over. In computer programming, a loop is a collection of instructions that are repeatedly carried out up until a particular condition is satisfied. Usually, a specific action, like receiving and changing some data, is followed by a conditional check, like seeing if a counter has reached a given value. Use a "For" loop to iterate over a specific section of code a predefined number of times. To check for a student's grade in the class, for instance.
Learn more about loops from
brainly.com/question/14390367
#SPJ4
the operating system _____ manages computer components, peripheral devices, and memory; maintains the system clock; and loads other operating system and application programs as they are requireda. platformb. kernelc. registryd. memoryAnswer: b. kernel
Answers
The operating system kernel controls how the computer works, how peripheral devices and memory are used, how the system clock is kept accurate, and how other operating systems and application programs are loaded as needed.
What kind of computer program controls memory?The most significant category of system software are operating systems. An operating system is a piece of software that maintains the computer's memory, processes, and all of its software and hardware. It governs how your hardware operates.
What kind of software manages the distribution of storage and memory?A computer's operating system (OS) is a piece of software that manages how resources are allocated among users. Examples of typical resources include the central processing unit (CPU), computer memory, file storage, input/output (I/O) devices, and network connections.
To know more about program visit:-
https://brainly.com/question/11023419
#SPJ4
Robots collect information about their surroundings using various sensors.
Sensors are devices that allow a machine to collect sensory data from the
natural world, such as ________________________and many more.
Whether it’s a robot using sensors or a human using senses, the
process of collecting sensory data is called ______________..
In addition to sensors, some robots have . ____________________.
These robots can interpret the ______________they collected so they can
actually __________________________of it.
When AI makes sense out of data, it is called __________________________.
this is a big part of what sets AI apart from other ___________________.
n
As a human does parkour, they are using their _____________________to gather
____________________(or data) about their _________________.
They might see a fence → and __________ it
They might feel soft ground → and _______ on it
They might use their arms → and ___________
Humans are able to _______________ lots of types of data, and then make
sense of it, ____________________________________of moving through the
world.
Computers don’t have this life experience!
It would be very hard for computers to use __________ and ________ to
complete a task as complicated as parkour in a variety of changing
__________..
A robot doing parkour needs to be able to ______ and make _____ very
quickly as it moves around.
Part 2. What were the examples of AI robots that we saw in the video?
Define or describe the following terms below.
Palletizers
Drive Units Robots
Thermal Imaging Drone
Airborne Optical Sectioning
Autonomous Drones
Part 3 . Answer the questions below based on the slides.
How do you think these robots use sensing?
How do you think they use perception?
How do you think these robots might collect information about their surroundings?
How do you think they know what to do with the information they collect?
Can you think of some problems that could be solved with the help of
robots that can quickly maneuver around or over obstacles?
Answers
Robots' senses enable them to learn about their surroundings.
Today, how are robots used?Robots have developed further, and today they are employed in homes as vacuum cleaners, pets, and toys. Industry, health, science, space exploration, construction, food packing, and even surgery are just a few of the areas that use robots today.
Why do robots matter?Robots can work in dangerous environments, thus humans are no longer required to accomplish certain tasks. They are capable of handling heavy lifting, hazardous materials, and repetitive tasks. This has not only saved businesses money and time, but also helped them avoid innumerable accidents.
To know more about Robots visit:
https://brainly.com/question/29379022
#SPJ1
Air at standard conditions flows steadily at low speed through a horizontal nozzle, discharging to atmosphere, where the pressure is Patm, meaning P2 = Patm. Inlet and exit areas of the nozzle are A1 = 0.10 m2 and A2 = 0.02 m2 , respectively.
Calculate the pressure required at the nozzle inlet, meaning P1, to yield an exit speed of 50 m/s.
Answers
Using Bernoulli equation we can say that the pressure required at the nozzle inlet, meaning P1, to yield an exit speed of 50 m/s is 1.48 kPa.
How do we calculate the pressure required at the nozzle inlet using Bernoulli equation?equations that control:
[tex]\frac{p_{1}}{\rho}+\frac{V_{1}^{2}}{2}+g z_{1}=\frac{p_{2}}{\rho}+\frac{V_{2}^{2}}{2}+g z_{2}[/tex]
Continuity for incompressible and uniform flow:
[tex]\sum_{\mathrm{CS}} \vec{V} \cdot \vec{A}=0[/tex]
We know that
1) Steady flow.
(2) Incompressible flow.
(3) Frictionless flow.
(4) Flow along a streamline.
(5)[tex]z_{1}=z_{2}[/tex]
(6) Uniform flow at sections (1) and (2).
The maximum speed of 50 m/s is well below 100 m/s, which corresponds to Mach number M≈0.3 in standard air. Hence, the flow may be treated as incompressible.
Apply the Bernoulli equation along a streamline between points (1) and (2) to evaluate [tex]p_{1}[/tex]
p1 − patm = p1 − p2 = ρ/2 (V2^2 −V1^2)
-ρV₁A₁ + ρV₂A₂ = 0 or V₁A₁ = V₂A₂
V₁ = V₂A₂/A₁ = 50 x 0.02/0.10 = 10 m/s
Since air at standard condition , ρ = 1.23 kg/m³
p1 − patm = ρ/2. (V₂²^2−V₁^²)
= 1/2 × 1.23 x (50² −10²)
= 1.48kPa
To know more about Bernoulli equation refer:
https://brainly.com/question/9506577
#SPJ4
Construct a Turing machine that generates all strings in reverse lexicographic order between the two provided strings X and Y. An input will be of the form "X,Y", where X is an element of {0, 1, 2}+ and Y is an element of {0, 1, 2}*. Your Turing machine must be a single tape, one way infinite, deterministic Turing machine. For this program you can use the left, right, and stay directives. When the Turing machine completes, the tape should contain a comma delimited list of all strings over {0, 1, 2}* in reverse lexicographic order starting with X and ending with Y. When your program completes it should accept the input and position the r/w head at the leftmost symbol of X.
Answers
The complete program regarding the quetions below
State q0:
Read 0: Move right and go to q0.
Read 1: Move right and go to q1.
Read 2: Move right and go to q2.
State q1:
Read 0: Move right and go to q1.
Read 1: Move right and go to q2.
Read 2: Move right and go to q3.
State q2:
Read 0: Move right and go to q2.
Read 1: Move right and go to q3.
Read 2: Move right and go to q4.
State q3:
Read 0: Move right and go to q3.
Read 1: Move right and go to q4.
Read 2: Move right and go to q5.
State q4:
Read 0: Move right and go to q4.
Read 1: Move right and go to q5.
Read 2: Move right and go to q6.
State q5:
Read 0: Move right and go to q5.
Read 1: Move right and go to q6.
Read 2: Move right and go to q7.
State q6:
Read 0: Move right and go to q6.
Read 1: Move right and go to q7.
Read 2: Move right and go to q8.
State q7:
Read 0: Move right and go to q7.
Read 1: Move right and go to q8.
Read 2: Move left and go to q7.
State q8:
Read 0: Move left and go to q8.
Read 1: Move left and go to q7.
Read 2: Move left and go to q6.
State q9:
Read 0: Move left and go to q9.
Read 1: Move left and go to q8.
Read 2: Move left and go to q5.
State q10:
Read 0: Move left and go to q10.
Read 1: Move left and go to q9.
Read 2: Move left and go to q4.
State q11:
Read 0: Move left and go to q11.
Read 1: Move left and go to q10.
Read 2: Move left and go to q3.
State q12:
Read 0: Move left and go to q12.
Read 1: Move left and go to q11.
Read 2: Move left and go to q2.
State q13:
Read 0: Move left and go to q13.
Read 1: Move left and go to q12.
Read 2: Move left and go to q1.
State q14:
Read 0: Move left and go to q14.
Read 1: Move left and go to q13.
Read 2: Move left and go to q0.
State q15:
Read 0: Move left and go to q15.
Read 1: Move left and go to q14.
Read 2: Stay in q15.
State q16:
Read 0: Print 0 and move left until the end of the string Y.
Read 1: Print 1 and move left until the end of the string Y.
Read 2: Print 2 and move left until the end of the string Y.
State q17:
Read 0: Print 0 and move left and go to q16.
Read 1: Print 1 and move left and go to q16.
Read 2: Print 2 and move left and go to q16.
What is program?
Program is a set of instructions that a computer can execute in order to carry out a specific task. Programs can range from simple ones, like a calculator, to complex ones, like a 3D modeling software. Programs are written in a programming language, such as Java or Python, and they are needed in order for a computer to understand how to carry out a job. Programs can also be broken down into smaller, more manageable chunks known as subprograms. Each subprogram is written with specific instructions that the computer can understand and execute
To learn more about program
https://brainly.com/question/27359435
#SPJ4
The heart of the recent hit game SimAquarium is a tight loop that calculates the average position of 256 algae. You are evaluating its cache performance on a machine with a 1024-byte direct-mapped data cache with 16-byte blocks (B = 16).You are given the following definitions://Codestruct algae_position {int x;int y;};struct algae_position grid[16][16];int total_x = 0, total_y = 0;int i, j;//End of CodeAssuming the cache starts empty, when the following code is executed://Codefor (i = 0; i < 16; i++) {for (j = 0; j < 16; j++) {total_x += grid[i][j].x;}}for (i = 0; i < 16; i++) {for (j = 0; j < 16; j++) {total_y += grid[i][j].y;}}//End of CodeThere are (Blank_1) total reads or loads and (Blank_2) reads or loads that miss in the cache,resulting in a cache miss rate of (Blank_3) %.Assuming the cache is emptied again, when the following code is executed://Codefor (i = 0; i < 16; i++) {for (j = 0; j < 16; j++) {total_x += grid[i][j].x;total_y += grid[i][j].y;}}//End of codeThere are (Blank_4) total reads or loads and (Blank_5) reads or loads that miss in the cache,resulting in a cache miss rate of (Blank_6) %.If the cache was twice as big, the miss rate would be (Blank_7) %.A: I got Blank_1 = 512, Blank_2 = 256 and Blank_3 = 50%.I can't seem to figure out the answers for the second loop
Answers
The answer for the second loop is, Total reads or loads = 16 * 16 * 2 = 512
So, Blank_4 = 512
Reads or loads that miss in the cache are 256 because accessing x-coordinates is always missed and accessing y-coordinate is always hit
Blank_5 = 256
Resulting in a cache miss rate is 256/512 = 0.5
Blank_6 = 50%
If the cache is twice as big, it would be 128/512 =0.25
Blank_7 = 25% because a cache was as large for storing the entire grid.
What is cache ?
A cache, which is pronounced "cash," is a piece of hardware or software that is used to temporarily store something in a computing environment, typically data. To enhance the performance of recently or often accessed data, a small quantity of quicker, more expensive memory is employed.
Hence to conclude cache miss rate is 0.5
To know more on cache follow this link:
https://brainly.com/question/25704927
#SPJ4
When a 136 N bag of nails hangs motionless from a single vertical strand of rope, how much tension is exerted in the strand? Answer in units of N.
Answers
The upward force of the rope and the downward force of the weight of nails must be exactly equal as it meets the bag. If there were a net force present there instead of zero, the point would be moving either upward or downward. Therefore, the rope's upward force at that location is 136 N.
The bag is not accelerating up or down if it is still. You can infer from that fact alone that there is no net vertical force acting on it. The total of all upward forces acting on it is therefore exactly equal to the gravitational force acting downward, or the "weight" of the bag. If the bag is strung from a single rope, the rope's tension must match the bag's 136-N weight. And if it is supported by four ropes, the total tension of those four ropes is 136N. I am unable to comment on the rope's increased level of tension. If the rope itself has any mass, then points further up must hold both the weight of the rope segment below the point as well as the weight of the bag of nails .If the rope has no mass, then its entire length is under 136 N of strain.
Learn more about bag from
brainly.com/question/16786026
#SPJ4
using the data below, what is the value of the mean absolute percent error (mape)? week time series value forecast 1 17 18.00 2 25 20.00 3 14 15.00 4 23 14.00
Answers
The value of the mean absolute percent error (mape)
What is mean?
Mean is an average value calculated by adding a set of numbers and then dividing by the number of items in the set. It is a measure of central tendency in a set of data and is often used to describe the overall trend or pattern in the data. Mean can also be used to compare sets of data and is often used to compare the performance of different groups of people or businesses.
The mean absolute percent error (MAPE) is a measure of the accuracy of a forecast. It is calculated by taking the mean of the absolute percent errors (the difference between the forecast and the actual value), divided by the mean of the actual values.
For the given data, the MAPE is calculated as follows:
MAPE = (|18.00 - 17| + |20.00 - 25| + |15.00 - 14| + |14.00 - 23|)/(17 + 25 + 14 + 23) = 0.30
Therefore, the mean absolute percent error (MAPE) for the given data is 0.30.
To learn more about mean
https://brainly.com/question/1136789
#SPJ1
1. What is the primary goal of penetration testing? a. Attempt to uncover deep vulnerabilities and then manually exploit them b. Scan a network for open FTP ports c. Perform SYN DOS attack towards a server in a network d. Attempt to perform an automated scan to discover vulnerabilities
2. There is often confusion between vulnerability scanning and penetration testing. What is the best explanation of the difference between vulnerability scanning and penetration testing? a. Vulnerability scanning is performed using an automated tool to scan a network known vulnerability signatures. Penetration testing involves attempting to manually uncover deep vulnerabilities just as a threat actor would, and then exploiting them. b. Vulnerability scanning checks a network for outdated versions of services. Penetration testing is attempting to manually uncover deep vulnerabilities just a threat actor would, and then exploiting them. c. Vulnerability scanning is performed by manually scanning a network for known vulnerabilities. Penetration testing is attempting to manually scan a network for known vulnerability signatures using an advanced scanning tool. d. Vulnerability scanning checks a network for open ports and services. Penetratic testing is attempting to manually scan a network for known vulnerability signatu using an advanced scanning tool. 3. Khalid joins a security team where he is assigned an SOC developer role and has to build different teams under SOC. Which of the following teams should he build to deal with providing real-time feedback related to security incidents and threat detections, which can then be utilized to facilitate better prioritization of threats and a mature way of detecting threats? a. Red team b. Blue team c. Purple team d. White team
Answers
1) Note that the primary goal of penetration testing is to 2Attempt to uncover deep vulnerabilities and then manually exploit them" (Option A)
2) The best explanation for the difference between vulnerability scanning and penetration testing is; "Vulnerability scanning is performed using an automated tool to scan a network known vulnerability signatures. Penetration testing involves attempting to manually uncover deep vulnerabilities just as a threat actor would, and then exploiting them." (Option A)
3) Given the above scenario, the team that he should build to deal with providing real-time feedback related to security incidents and threat detections, which can then be utilized to facilitate better prioritization of threats and a mature way of detecting threats is "the Purple Team" (Option C).
Why is Penetration Testing Important?The major reason penetration testing is important for an organization's security is that they teach staff how to deal with any form of hostile entity break-in. Pen tests are used to determine whether a company's security practices are truly effective.
Some compliance rules require penetration testing. Aside from that, you should conduct regular pentests to analyze and upgrade your security procedures against cyberattacks.
Learn more about Penetration Testing;
https://brainly.com/question/29560410
#SPJ1
The following time series shows the number of units of a particular product sold over the past six months. Month Units sold (thousands) 1 8 2 3 3 4 4 S 5 12 6 10 a. Compute a 3-month moving average (centered) for the above time series. b. Calculate the mean square error (MSE) for the 3-month moving average. c. Use a = 0.2 to determine the exponential smoothing values for the time series
Answers
a. To compute a 3-month moving average (centered) for the above time series, we need to take the average of each set of 3 consecutive months.
What is moving average?A moving average is a statistical technique used to analyze a dataset by smoothing out short-term fluctuations and identifying longer-term trends or patterns. It does this by calculating the average of a set of consecutive data points and plotting that average as a line on a graph.
The size of the set of data points used to calculate the average is called the window size.
For example, if the window size is 3, a 3-month moving average would be calculated by taking the average of the current month and the two preceding months.
If the window size is 5, a 5-month moving average would be calculated by taking the average of the current month and the four preceding months, and so on.
Moving averages are often used in financial analysis to smooth out the noise in stock price data and identify trends or patterns that may not be immediately apparent.
They can also be used in other fields, such as meteorology, to smooth out short-term variations in temperature or precipitation data and identify longer-term trends.
To Know More About dataset, Check Out
https://brainly.com/question/28362021
#SPJ4
Some Linux systems use the __________________ script to perform the same actions each time a user logs out of her account.a. .bash_logoutb. .bash_rcc. /bin/bashoutd. /etc/logoff_bash
Answers
The bash rcc script is used by some Linux systems to carry out the same tasks each time a user logs out of her account.
The Linux family of open-source Unix-like operating systems is based on the Linux kernel, which Linus Torvalds initially made available on September 17, 1991. Linux distributions, which are how Linux is commonly packaged, frequently include the kernel and other system-supporting programmes and libraries, many of which are made available by the GNU Project. Although the Free Software Foundation likes to refer to their operating system as "GNU/Linux" to emphasise the importance of GNU software, many Linux versions have the term "Linux" in their names. This has caused some controversy. The most well-known Linux distributions are Debian, Fedora Linux, and Ubuntu. Lubuntu and Xubuntu are just two of the many distributions and modifications that make up Ubuntu.
Learn more about Linux systems from
brainly.com/question/29773084
#SPJ4
the operation of marine transportation determines the efficiency ofmoving goods. the progress in terminals, technologies and management principles improves the moving load, delivery speed in g
Answers
The movement of persons or cargo across waterways is referred to as marine transportation. The company that offers water transportation is called Marine Transport Management, Inc.
How significant is maritime transportation?International trade and the world economy are based on maritime transportation. The number is significantly higher for the majority of poor nations, where shipping accounts for over 80% of all international trade in products. Since 1968, UNCTAD has released the Review on Maritime Transport, which is its flagship report.
Operations and management in the maritime sector are what?The primary goal of this program is to equip you with the knowledge and abilities needed to land prestigious jobs in the offshore and maritime sectors. You will develop the self-assurance necessary for a senior position in the maritime industry in the interpersonal and cross-cultural competencies.
To know more about waterways visit :-
https://brainly.com/question/2453542
#SPJ4
Five telemetry signals, each of bandwidth 240 Hz, are to be transmitted simultaneously by binary PCM. The signals must be sampled at least 20% above the Nyquist rate. Framing and synchronizing requires an additional 0.5% extra bits. A PCM encoder is used to convert these signals before they are time-multiplexed into a single data stream. Determine the minimum possible data rate (bits per second) that must be transmitted, and the minimum bandwidth required to transmit the multiplex signal.
Answers
To determine the minimum data rate and minimum bandwidth required to transmit the multiplex signal, we need to first determine the minimum sampling rate required to sample each of the telemetry signals. The Nyquist rate is defined as half the bandwidth of the signal, so the Nyquist rate for each telemetry signal is 120 Hz. To sample at least 20% above the Nyquist rate, we need to sample at a rate of at least 120 Hz * 1.2 = 144 Hz.
Since there are 5 telemetry signals, the total number of samples per second is 5 * 144 = 720 samples/s. Since the signals are being encoded using binary PCM, each sample will require 1 bit to represent it. This means that the minimum data rate required to transmit the multiplex signal is 720 samples/s * 1 bit/sample = 720 bits/s.
To determine the minimum bandwidth required to transmit the multiplex signal, we need to consider the bandwidth required for the 5 telemetry signals as well as the additional bandwidth required for framing and synchronization. The total bandwidth required for the telemetry signals is 5 * 240 Hz = 1200 Hz. The additional bandwidth required for framing and synchronization is 1200 Hz * 0.5% = 6 Hz. The total minimum bandwidth required to transmit the multiplex signal is 1200 Hz + 6 Hz = 1206 Hz.
The maximum pace of data flow along a particular path is referred to as bandwidth in computing. Network bandwidth, data bandwidth, and digital bandwidth are three different types of bandwidth.
Contrary to this definition, bandwidth is used to refer to analog signal bandwidth measured in hertz, which is the frequency range between the lowest and highest attainable frequency while meeting a well-defined impairment level in signal power in the fields of signal processing, wireless communications, modem data transmission, digital communications, and electronics.
The actual bit rate that may be obtained is influenced by the channel noise as well as the signal bandwidth.
Learn more about bandwidth, from:
brainly.com/question/28436786
#SPJ2
FET ______ circuits are commonly used in triggering, speed control, and power supply circuits.
Answers
FET Switching circuits are commonly used in triggering, speed control, and power supply circuits.
What is power supply circuits?A type of transistor called a field-effect transistor (FET) uses an electric field to regulate the flow of current in a semiconductor. Source, gate, and drain are the three terminals on FETs (also known as JFETs or MOSFETs). Applying a voltage to the gate of a FET changes the conductivity between the drain and source, which in turn regulates the current flow.
Due to their single-carrier-type operation, FETs are also referred to as unipolar transistors. In other words, FETs only use one of the two charge carriers—either electrons (n-channel) or holes (p-channel)—in order to function.
Field effect transistors come in a variety of forms. Input impedance at low frequencies is typically very high for field effect transistors. The MOSFET is the field-effect transistor that is most frequently used (metal-oxide-semiconductor field-effect transistor).
Learn more about transistor
https://brainly.com/question/1426190
#SPJ4
a byte-addressable main memory of size 256mb with blocks of 32 bytes in size. the cache memory can hold up to 64 blocks
Answers
The main memory can hold a total of (256 * 1024 * 1024) / 32 = 8,388,608 blocks.
What are main and cache memory?he main memory in this system has a size of 256 megabytes, which is equal to 256 * 1024 * 1024 bytes. With blocks of 32 bytes in size, this means that the main memory can hold a total of (256 * 1024 * 1024) / 32 = 8,388,608 blocks.
The cache memory, on the other hand, can hold up to 64 blocks. This means that it can store a small fraction of the data that is stored in the main memory. In order to access data that is not stored in the cache, the system must fetch it from the main memory, which takes longer than accessing data directly from the cache.
To Know More About main memory, Check Out
https://brainly.com/question/20813182
#SPJ4
an example of architecture with similar features to the persian fire temple pavilion featured in lecture was this early islamic tomb. tomb of ahmed
Answers
Tomb of ahmed is an example of architecture with similar features to the persian fire temple pavilion featured in lecture was this early islamic tomb.
Some information about Ahmad's Tomb:
Ahmad Shah's tomb, also known as Raja no Hajiro and Badshah no Hajiro (King's Mausoleum), is a collection of tombs built during the Medieval period in Ahmedabad. He is widely regarded as the founder of Ahmedabad, Gujarat. The exquisite artwork and architectural extravagance set the tomb apart from other tourist attractions and establishes it as a gold standard in Indian architecture.
Expectations when visiting Ahmad Shah's Tomb:
1. Ahmad Shah's tomb is one of Ahmedabad's most important tourist attractions.
2. The tomb is square in shape and has stone windows with lattice work. Women, on the other hand, are still not permitted in the central chamber of Ahmad Shah's Tomb.
3. Across the street is the Rani no Hajira, which houses the tombs of Ahmad Shah's queens. The tomb is in excellent condition, but the tombs of the queens have deteriorated.
4. Ahmad Shah's tomb is one of Ahmedabad's architectural wonders.
5. The artistic craftsmanship, latticed windows, and domes and minarets give the Tombs of Ahmad Shah an exquisite appearance. This tomb in Ahmedabad is a must-see for anyone interested in Mughal art and culture.
To know more about lattice work, visit: https://brainly.com/question/20038994
#SPJ4
