f the initial energy of a conservative system is ei and the final energy is ef, what can we say about the relationship between these two energies in such a system?

Answer:

It would triple.

Explanation:

By Newtown's law of universal gravitation, the ration is 1:1

We cannot determine the value of interference with the given information.

The interference can be determined using the following formula:

interference = (observed double crossover rate - expected double crossover rate) ÷ (1 - expected double crossover rate).

The expected double crossover rate can be calculated using the formula:

expected double crossover rate = (distance AB × distance BC) ÷ total distance (AB + BC + AC).

Given:

Distance between A and B is 10mu;

Distance between B and C is 15mu;

Observed double crossover rate is 0.25%.

Therefore,

Distance AB = 10mu;

Distance BC = 15mu;

Total distance = AB + BC + AC

Expected double crossover rate = (10 × 15) ÷ (10 + 15 + AC)

expected double crossover rate = 150 ÷ (AC + 25)

The observed double crossover rate is 0.25%.

Therefore, the observed double crossover rate = 0.25% = 0.0025.

Interference = (observed double crossover rate - expected double crossover rate) ÷ (1 - expected double crossover rate)=

[0.0025 - (150 / (AC + 25))] ÷ [1 - (150 / (AC + 25))]

what is the interference if: distance between a and b is 10mu distance between b and c is 15mu observed double crossover rate is: 0.25%

To learn more about interference:https://brainly.com/question/16098226

#SPJ11

A, B, and C are all assumptions made in the model for the motion of a pendulum, and if any of them are not valid, the model may not accurately describe the behavior of the pendulum. Therefore, option D is correct.

The model for the motion of a pendulum assumes that the pendulum is swinging without friction, the string is massless, and the amplitude of oscillation is small. These assumptions allow us to use the simple harmonic motion equation to describe the motion of the pendulum. However, if any of these assumptions are not true, the model may not be valid.

Therefore, if any of these assumptions are not valid, the model for the motion of the pendulum may not be accurate, and the results obtained from the model may not describe the actual behavior of the pendulum.

Hence Option d IS CORRECT.

For more similar questions on pendulum,

brainly.com/question/12306298

#SPJ11.

The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass.

An object-earth system is a system in which an object interacts with the earth by exerting a force of attraction. The object's energy is derived from the work done by gravitational forces when the object is moved away from the earth's surface.

An object in an object-earth system's gravitational potential energy is the work done by gravitational forces on the object when it is moved from a lower position to a higher one in the object-earth system. The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass. The gravitational potential energy of an object in the earth-object system is determined by the distance between the object and the earth's surface. The gravitational potential energy of an object increases as the distance between it and the earth's surface increases.

Learn more about the gravitational potential at brainly.com/question/19768887

#SPJ11

Coordinate , A - the height of the stone when it hits the water. A slingshot sends a stone vertically upward from a height of 20 feet above a pool of water.

The coordinate A represents the height of the stone when it hits the water. When the stone hits the water, its height above the water surface is zero.

So, we can set the expression for the stone's height equal to zero and solve for t to find the time when the stone hits the water. The height of the stone when it is launched is given as 20 feet, which is a fixed value in this problem.

The time when the stone is launched is also a fixed value, which is zero. The maximum height of the stone is the highest point the stone reaches above its initial height of 20 feet. The time when the stone reaches its maximum height is the time at which the vertical velocity of the stone becomes zero.

To know more about vertical velocity , visit :

https://brainly.com/question/11679227

#SPJ1

The fluid movement in a lava lamp is caused by the heat generated from the lamp's light bulb, which causes the wax or oil to rise and fall.

A lava lamp contains two fluids of different densities that do not mix. The fluids heat up as a result of the lamp's light bulb, causing them to expand and become less dense. The wax or oil floats up when it becomes less dense than the fluid that surrounds it, creating a globe at the top of the lamp.

The fluid is then cooled by the environment and becomes more dense, causing the wax to sink back to the bottom. This constant motion cycle creates the flowing effect seen in a lava lamp.

The heat from the light bulb causes the fluid to expand, and as it does, it becomes less dense than the surrounding fluid, causing it to float. When the fluid cools, it becomes denser and settles back down to the bottom. This cyclic motion creates the soothing flow of a lava lamp.

For more such questions on lava lamp, click on:

https://brainly.com/question/30542979

#SPJ11

The frequency detected by a stationary observer if the ambulance truck is moving 30 m/s toward the observer is 731.3 Hz.

When the ambulance truck emits sound with a frequency of 800hz and the ambulance truck is moving 30 m/s toward the observer,

The observed frequency is given by the following formula.

f’ = f [(v ± v_o)/(v ± v_s)]

Where v = the speed of sound in air = 343 m/s

f = frequency of the source = 800 Hz

v_o = velocity of the observer (stationary) = 0 m/s

v_s = velocity of the source (ambulance truck) = -30 m/s (since the ambulance truck is moving toward the observer)

Now we can plug in the values into the formula and calculate the observed frequency.

f' = 800 ((343 - 30) / (343 + 0))

= 800 (313 / 343)

= 731.5 Hz (rounded to one decimal place)

If the ambulance truck is moving towards a stationary observer at a speed of 30 m/s, the frequency detected by the observer is 731.3 Hz.

To know more about "observed frequency" in physics: https://brainly.com/question/15056533

#SPJ11

The final velocity of the plane after a missile of mass 1.20 102 kg is fired from the plane  is 0.255 m/s.

To find the final velocity of the plane when a missile of mass 1.20 x 10² kg is fired from a plane of mass 4.80 x 10³ kg initially moving at a speed of 3.25 x 10² m/s, and the speed of the missile relative to the plane is 1.06 x 10³ m/s, we can use the conservation of momentum.The initial momentum of the system is given by:

m1v1 + m2v2 = (m1 + m2)vf

where m1 = mass of missile, m2 = mass of the plane, v1 = velocity of the missile, v2 = velocity of the plane, and vf = final velocity of the system

Substituting the given values, we get:(1.20 x 10² kg) (1.06 x 10³ m/s) + (4.80 x 10³ kg) (3.25 x 10² m/s) = (1.20 x 10² kg + 4.80 x 10³ kg) vf

Simplifying, we get:1284 = (5.04 x 10³ kg) vf

Therefore, vf = 1284 / (5.04 x 10³ kg) = 0.255 m/s. So, the final velocity of the plane is 0.255 m/s.

More on velocity: https://brainly.com/question/20038545

#SPJ11

The example in which the distance you travel is different from your

displacement will be "Suppose a person starts at point A and walks 5 meters to point B, and then turns around and walks back to point A, covering another 5 meters. The distance traveled by the person is the total length of the path traveled, which is 10 meters (5 meters + 5 meters).

However, the displacement of the person is the change in position from the starting point to the ending point, which is zero. So the distance traveled is different from the displacement, as the person ends up at the same position where they started, despite covering a total distance of 10 meters.

Displacement is a verb that denotes movement or displacement of an object. The definition of displacement is the modification of an object's position.

The term "displacement" refers to a shift in an object's position. It is a vector quantity with a magnitude and direction. The symbol for it is an arrow pointing from the initial location to the ending place. For instance, if an object shifts from location A to position B, its position changes.

Learn more about displacement on:

https://brainly.com/question/14422259

#SPJ1

Galileo famously observed that objects of different masses fall to Earth at the same rate, regardless of their mass. This observation led him to conclude that gravity was a universal force of attraction between any two objects with mass.

Galileo Galilei was an Italian astronomer, physicist, and mathematician who contributed greatly to the development of modern science. His contributions to physics include the creation of the scientific method and his work on the principles of motion and gravity.

Galileo was one of the first scientists to study gravity. He observed that objects of different weights would fall at the same rate when dropped from the same height. This led him to conclude that gravity is a constant force that acts upon all objects equally, regardless of their weight or composition.

Galileo's work on gravity laid the foundation for the later development of Sir Isaac Newton's theory of gravity. Newton built on Galileo's findings and formulated the law of universal gravitation, which states that every object in the universe attracts every other object with a force that is proportional to their masses and inversely proportional to the square of the distance between them.

Learn more about Galileo at https://brainly.com/question/4966012

#SPJ11

The proper subset relations that are possible using the sets of numbers n, z, q, and r are:

An improper subset comprises every element of the original set, while a valid subset only contains a fraction of the original set's numbers. A subset of a set A that is not equal to A is a proper subset of A. In other words, if B is a proper subset of A, then A has at least one element that is not in B but all of B's elements are in A.

Learn more about proper subset at brainly.com/question/17514113

#SPJ11

Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7J and 23.5J, for better understand we have to know the meaning of potential energy.

Potential energy in physics is the energy that an item retains as a result of its location in relation to other objects, internal tensions, electric charge, or other elements. Potential energy develops in systems having components whose configurations, or relative positions, determine the amount of the forces they apply to one another.

Potential Energy of an Object = m * g * h

Where, m = mass,

g = gravity, and

h = height

Potential Energy of Object W = 2 * 9.8 * 0

= 0 J

Potential Energy of Object X = 2 * 9.8 * 0.4

= 7.84 J

Potential Energy of Object Y = 2 * 9.8 * 0.8

= 15.68 J

≈ 15.7 J

Potential Energy of Object Z = 2 * 9.8 * 1.2

= 23.5 J

Therefore, Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7 J and 23.5 J.

To Learn more about Potential Energy, visit:

https://brainly.com/question/1242059

#SPJ1

The coordinated functions of the Nervous, Endocrine, and Reproductive systems are:

Coordinated functions refer to the integration and communication between different organs, systems, and tissues in the body to achieve a common goal or purpose. In biological terms, coordinated functions often involve multiple physiological systems working together to maintain homeostasis, respond to stimuli, or carry out complex behaviors or processes.

Examples of coordinated functions include the regulation of blood glucose levels by the pancreas and liver, the coordination of movement by the nervous and musculoskeletal systems, and the release of hormones by the endocrine system to control various physiological processes.

Learn more on coordinated functions here: https://brainly.com/question/15686131

#SPJ1

The question is:

"COORDINATED FUNCTIONS OF THE NERVOUS, ENDOCRINE, AND REPRODUCTIVE SYSTEMS"

Directions: Identify the part of the brain that is involved in each situation below. Write only the letter of your answer.

A. Amygdala

B. Brocka's Area

C. Cerebellum

D. Cerebrum

E. Hippocampus

F. Occipital Lobe

G. Hippocampus

H. Hypothalamus

I. Inferior Colliculus.

J. Thalamus

K. Pons

L Superior Colliculus

M. Pineal Gland

N. Wernicke's Area

O. Pituitary Gland

1. "My heart tells me that you are the one. I love you so much!"

2. "IAOCEVOY! I don't know what that means. It's all Greek to me!"

3. "Chartreuse, Olive,Turquoise, and Mint are all shades of green."

4. "Janna always wakes up at 4 in the morning, regardless of whether she uses an alarm clock or not."

5. "I don't remember the way going to Myla's house. Can you accompany me there?"

6. Jenny's mother is about to give birth, she complains about contraction and pain usually when the baby is kicking

7. "Anthony is a very skilled dancer. He just won the school hip hop dance competition last week."

8. "As Nica was walking on the road she readily moved to the side for she heard an incoming ambulance"

9. "Elsa loves making faces whenever she talks to her friends."

10. "Ryan usually talks about how happy his high school days were to his grandchildren."

When only one lightbulb blows out, an entire string of decorative lights goes out, which means that the lights in this string must be connected in series with one current pathway.

In a series circuit, the components are connected end to end in a single path, so the current flows through each component in turn. If one component, such as a lightbulb, fails, the circuit becomes incomplete, and the current cannot flow through any of the components downstream of the failed component. This results in all the lights in the series circuit going out when one lightbulb blows out.

In contrast, in a parallel circuit, the components are connected across multiple current pathways, so if one component fails, the current can still flow through the other components, and they will continue to function normally. Therefore, if one lightbulb blows out in a parallel circuit, the other lights will continue to work.

Learn more about the series circuit:

https://brainly.com/question/19865219

#SPJ11

The range of frequencies on the electromagnetic spectrum is known as the electromagnetic spectrum.

The spectrum ranges from radio waves, microwaves, infrared waves, visible light, ultraviolet rays, x-rays, and gamma rays. Each type of wave has a specific frequency range, ranging from hertz (Hz) to exahertz (EHz). The lowest frequency waves, such as radio waves, range from 3 kHz to 300 GHz, while the highest frequency waves, such as gamma rays, range from 300 GHz to 3 EHz.
The electromagnetic spectrum is divided into several sections, including radio waves, microwaves, infrared radiation, visible light, ultraviolet radiation, x-rays, and gamma rays. Each type of wave has its own properties and uses in different applications. Radio waves are used for communication, microwaves are used in satellite communication and imaging, infrared radiation is used in medical imaging, visible light is used to see our environment, ultraviolet radiation is used in sun protection and sterilization, x-rays are used in medical imaging and treatment, and gamma rays are used in medical treatment and research.

for such more question on electromagnetic spectrum

https://brainly.com/question/13803241

#SPJ11

Answer:

Explanation:

a) The mass of the cube can be calculated using the equation Mass = Volume x Density. The volume of the cube can be calculated as (5.00×10 cm)^3 = 125 cm³. Substituting this volume into the equation gives Mass = 125 cm³ x 7.86 g/cm³ = 983.5 g.

b) The number of iron atoms in the cube can be calculated using Avogadro's number (6.02 x 10^23 atoms/mol). The number of moles can be calculated using the molar mass of iron, 55.9 g/mol. Thus, the number of moles can be calculated as 983.5 g / 55.9 g/mol = 17.61 moles. Multiplying this by Avogadro's number gives the number of iron atoms in the cube as 1.07 x 10^24 atoms.

True. A Faraday bag (also known as an electromagnetic bag) is a container made from metal or a special material that blocks any electromagnetic emanations from passing into or out of the bag, preventing a mobile device from communicating with the outside world.

This is because Faraday bags are electromagnetic bags that are designed to isolate electronic devices from external electromagnetic influence. They are also known as radiofrequency shielding bags, Faraday cage bags, signal blocker bags, or electromagnetic pulse (EMP) bags.

What are Faraday bags?

Faraday bags are made of a combination of metal or metal-coated fabrics that are designed to block electromagnetic signals from entering or leaving the bag. They are usually used to keep mobile devices such as smartphones and tablets from communicating with the outside world, especially in situations where an individual is worried about their privacy or security. They are also used by law enforcement agencies to prevent suspects from remotely wiping or deleting evidence on their devices.

How do Faraday bags work?

Faraday bags work by using a principle known as the Faraday effect, which states that any electric field in a conductor is shielded from the conductor's interior by the presence of an electric field. Faraday bags use this principle to block incoming and outgoing signals by creating an electrically conductive enclosure around the device. This means that when a mobile device is placed inside a Faraday bag, the bag acts as a Faraday cage, which shields the device from electromagnetic radiation. As a result, the device cannot communicate with the outside world.

For further details about Faraday bag, click on the below link:

https://brainly.com/question/23083952

#SPJ11

The Volumetric efficiency of the pump is the ratio of the actual capacity to the theoretical capacity of the pump.

Volumetric efficiency of the pump = Actual capacity of the pump / Theoretical capacity of the pump

Given Information

The provided information is,

Find

The theoretical capacity of the pump is given by the following formula,

Theoretical capacity of the pump = π/4 x d² x l x n

where:

For the given problem,

We need to find the diameter of the pump and length of the pump to calculate the theoretical capacity of the pump.

Now, we have the actual capacity of the pump.

As we don't have the diameter and length of the pump, it is impossible to calculate the theoretical capacity of the pump.

Hence, the Volumetric efficiency of the pump cannot be calculated.

Learn more about Volumetric efficiency: https://brainly.com/question/14783214

#SPJ11

The average arterial pressure in your hands when they are held at your side is 47.5 mmHg.

The average arterial pressure in your hands when they are held at your side can be determined using the hydrostatic pressure formula, which is a function of height, gravity, and density. When the hands are held at the side, they are 60 cm below the heart, which means they are at a distance of 0.6 m.

The hydrostatic pressure formula is given by

P = ρgh

Where,

P is the pressure, ρ is the density, g is the acceleration due to gravity, and h is the height. We can assume that the density of blood is constant, and we can take the value of g to be 9.81 m/s², the standard acceleration due to gravity.

Therefore, the pressure at the heart is 100 mmHg, or 100/760 = 0.131 atm. The pressure in the hands can be calculated as follows:

P = ρghP = (1.06 × 10³ kg/m³) × (9.81 m/s²) × (0.6 m)

P = 6.26 × 10³ N/m²

P = 6.26 × 10³ Pa

P = 47.5 mmHg

Therefore, the average arterial pressure in the hands when they are held at the side is 47.5 mmHg.

Learn more about hydrostatic pressure at https://brainly.com/question/28206120

#SPJ11

The volume of the solid obtained by rotating the region in the first quadrant bounded by the curves x = 0, y = 1, x = y^7 about the line y = 1 is 0.

To determine the volume of the solid obtained by rotating the region in the first quadrant bounded by the curves x = 0, y = 1, x = y^7 about the line y = 1, we need to use a specific integral formula.

The volume of the solid is calculated by multiplying the area of the cross-section of the solid, which is perpendicular to the axis of rotation, with the distance traveled by the center of mass of the cross-section. And, when this product is summed up across the length of the solid, we get the volume of the solid.

To solve the given problem, the area of the cross-section of the solid is [tex]\pi (r)^2[/tex], where r is the distance from the line y = 1 to the curve [tex]x = y^7[/tex]. Since the cross-section is a circle, we know the area of the cross-section can be represented by the equation of a circle with radius r, which is [tex]\pi (r)^2[/tex].

To find the value of r, we will equate  [tex]x = y^7[/tex] to the line y = 1. By solving for y, we get: [tex]y = 1^{1/7} = 1[/tex].

Hence, r = 1 - 1 = 0.

We can now compute the volume of the solid using the integral formula:

[tex]V =\int_0^1 \pi (r)^2 dy\\V = \int_0^1 \pi (0)^2 dy\\V = \int_0^1 0 dy\\V = 0[/tex]

Learn more about volume of the solid here:

https://brainly.com/question/24259805

#SPJ11

The statement the construction of psychological profiles is a process of mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones is TRUE.

Psychological profiling is a technique used by law enforcement agencies to identify the characteristics of an offender based on their behavior patterns, motives, and other psychological traits. It is a process of creating a psychological profile of an offender by analyzing the crime scene, victimology, and other evidence related to the crime.

This profile is then compared with the profiles of previously solved crimes to identify potential suspects or patterns that can be used to solve unsolved crimes. The process involves mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones.

The psychological profile is based on the assumption that an offender's behavior is consistent across different crimes and that it reflects their personality traits and motivations. This technique has been used successfully in many high-profile cases and has helped law enforcement agencies to identify and apprehend serial offenders.

To know more about psychological profiles, refer here:

https://brainly.com/question/30398442#

#SPJ11

One of the methods which will not reduce reactivity of observation is telling the person you are observing his/her behaviour. Correct option is B.

A practical, utilitarian approach, behavioral observation focuses on the plainly discernible ways in which the client engages with his or her surroundings. Behavioural observation can be used as a standalone technique or casually as a component of an interview, a test, or both.

Waiting until the subjects of the observation are used to the observer is one method to reduce reactivity. Another option is to have the observer document the actions without the subjects being aware of the observation.

The act of observation modifies in some manner the situation in which a participant is being observed. Within an experimental setting, reactivity is viewed as a threat to internal validity because the change in behaviour is not due to the experimental manipulation. Best choice is B.

To know more about observations:

https://brainly.com/question/30454101

#SPJ4

Hominin remains have been found at sites throughout Africa, Europe, and Asia. Below are five of these fossil sites and their main finds. The correct order of the given hominin fossil sites from oldest to youngest is Omo kibish, Klasies river, Herto, and Tianyuan cave.

Omo kibish is incomplete fossil skull (oldest)The oldest fossil site on the list is Omo kibish in Ethiopia, which is dated to around 195,000 years ago. The site has a partial skull, lower jawbone, and a few other fragments of the skull. Klasies river is fragmentary hominin remains Klasies river Mouth in South Africa is dated back to around 120,000 years ago. The site contains human fossils along with the remains of other animals.

Herto is a skull intermediate between H. heidelbergensis and modern H. sapiens, Herto Bouri in Ethiopia, dated to around 160,000 years ago. The site contains 3 complete hominid skulls which were much more modern than expected for their age. The skulls were similar to Homo sapiens, but with some differences. Tianyuan cave is modern human maniple and femur (youngest). Tianyuan cave in China, dated to around 40,000 years ago, contains one of the earliest modern human fossils. A complete set of human teeth and bones from a foot, leg, and hand were found at this site.

Learn more about hominin at:

https://brainly.com/question/30791663

#SPJ11

At the shop, Joselyn purchased 2700 grammes of salt water taffy.

To convert kilograms (kg) to grams (g), Joselyn would need to multiply the weight in kilograms by 1000. This is because there are 1000 grams in 1 kilogram. Therefore, to find out how many grams of salt water taffy Joselyn bought, she would need to multiply 2.7kg by 1000.

The correct answer is (B) Multiply by 1000.

Multiplying 2.7kg by 1000 gives:

2.7kg x 1000 = 2700g

So Joselyn bought 2700 grams of salt water taffy at the store.

To learn more about salt water refer to:

brainly.com/question/6829606

#SPJ4

Answer:

Light energy

Explanation:

When an electron releases or absorbs energy, it goes into an "exited state" which means it goes into a lower or higher energy level respectively. This will radiate light energy.

The meter stick is in static rotational equilibrium, which means that the sum of the clockwise torques must equal the sum of the counterclockwise torques. The torque is equal to the force multiplied by the distance from the support point, so we can set up the equation:  
CW Torque (5 cm mark): 220 g x 5 cm = 1100 g-cm
CW Torque (90 cm mark): 120 g x 90 cm = 10,800 g-cm
CCW Torque (40 cm mark): M x 40 cm = M x 40 cm
1100 g-cm + 10,800 g-cm = M x 40 cm
M = (1100 + 10,800) / 40 = 250 g
Therefore, the mass of the meter stick is 250 g.

Rotational equilibrium refers to the condition in which an object is motionless and still rotating. The condition occurs when the net torque on an object is equal to zero.

Read more about the topic of rotational equilibrium:

rainly.com/question/31142588

#SPJ11

The sample size with some specified width error by reducing the confidence level to 80% is 3 times the original sample size and the width error which have been scaled in size compared to the original width error is by a factor of 10.

When reducing the confidence level to 80% and the original width (error) E by a third, the new sample size will be 3 times the original size. To calculate this, use the formula n = (zα/2 / E)² × σ2.

If the original confidence level was 95%, then the original zα/2 = 1.96. If the new confidence level is 80%, then the new zα/2 = 1.282.

The original error was E, and the new error is 1/3 E. By substituting these values into the formula, we get n = (1.282 / (1/3 E))² × σ2. This simplifies to n = 3 × (1.96 / E)² × σ2, which is 3 times the original sample size.

If the original confidence level was 95%, then the original zα/2 = 1.96.

If the new confidence level is 85%, then the new zα/2 = 1.44.

The original error was E, and the new error is 10E.

By substituting these values into the formula, we get n = (1.44 / (10E))² × σ2.

This simplifies to n = (1.96 / E)² × σ2, which is 10 times the original sample size.

Therefore, the width (error) will have scaled in size by a factor of 10 compared to the original width (error) E.

Learn more about Sample size here:

https://brainly.com/question/25894237

#SPJ11

The work required to raise the elevator from the basement to the third floor is equal to the force times the distance moved. The work required is equal to (-pounds)(ft) = -foot-pounds.

We have to calculate the work required to raise the elevator from the basement to the third floor using the given data. In order to calculate the work, we need to determine the force required to lift the elevator.

This can be done using the equation: F = W + w x L

where, F is the force required to lift the elevator, W is the weight of the elevator, w is the weight of the cable per foot, and L is the length of the cable. F = 1500 + (0.4 × 75) = 1500 + 30 = 1530 pounds.

Therefore, the force required to lift the elevator is 1530 pounds. The work done to raise the elevator is given by the equation: W = F × d

where, W is the work done, F is the force required to lift the elevator, and d is the distance traveled by the elevator.

W = 1530 × 30 = 45,900 foot-pounds.

Therefore, the work required to raise the elevator from the basement to the third floor is 45,900 foot-pounds.

Read more about the distance ;

https://brainly.com/question/26550516

#SPJ11

The fluid force on one side of the 5ft by 5ft plate lying flat on its 5ft by 5ft face, we can use the equation F = ρghA and the F = 1,945,000 N.

Since the plate is at the bottom of the pool and the pool is filled with water to a depth of 8ft, h = 8ft and the area of the plate A = 5ft × 5ft = 25ft².

There F is the fluid force, ρ is the density of the fluid, g is the acceleration due to gravity, h is the depth of the fluid, and A is the area of the plate.

Therefore, the fluid force on one side of the plate is:

F = ρghA = 1000kg/m³ × 9.81m/s² × 8ft × 25ft² = 1,945,000 N.

To calculate the fluid force on one side of the plate resting vertically on a 5 ft edge, we can use the same equation as above but with an area equal to the length of the plate multiplied by the depth of the pool (8ft):

F = ρghA = 1000kg/m³ × 9.81m/s² × 8ft × 5ft = 392,000 N.

To calculate the fluid force on one side of the plate resting on a 5ft edge and tilted at 45 degrees to the bottom of the pool, we can use the same equation as above but with an area equal to the length of the plate multiplied by the depth of the pool multiplied by the cosine of the angle of the plate:

F = ρghA = 1000kg/m³ × 9.81m/s² × 8ft × 5ft × cos(45) = 283,200 N.

Read more about the force here:

https://brainly.com/question/12785175

#SPJ11

All but  option A: the plant is exposed to light condition must be present for the Calvin cycle reactions to occur.

The Calvin cycle is the biochemical process that takes place in the chloroplasts of plants, in which carbon dioxide is fixed into glucose molecules. This process involves several enzymes and molecules, but the energy needed to power the process comes from ATP and NADPH, which are produced during the light-dependent reactions that take place in the thylakoid membranes of the chloroplasts.

Therefore, light is required for the Calvin cycle to occur since it is the source of the energy that drives the reaction. However, all parts of the plant do not need to be exposed to light for the Calvin cycle to occur. Only the chloroplasts, which are found in the mesophyll cells of the plant, need to be exposed to light for photosynthesis to occur.

Learn more about Calvin cycle from

https://brainly.com/question/920840

#SPJ1

See full question below

all but which condition must be present for the calvin cycle reactions to occur?

The plant is exposed to light

water is not involved in any of the reactions

light energy is converted into chemical energy

provide the electrons needed to reduce NADP