Answer:
Part A
Time period, designated by the symbol, 'T', is defines as the time it takes for a complete cycle of an oscillation or vibration (of a wave) to transit through a given point.
The longer the time period of a wave, the lower the frequency of the wave
The unit of the time period is seconds, 's'
Part B
Mathematically, the formula for the time period is presented as follows;
f = 1/T
∴ T = 1/f
f = v/λ
∴ T = λ/v
Where;
v = The velocity of the wave;
λ = The wavelength of the wave
Explanation:
Một dây dẫn đặt trong không khí có dòng điện I = 12A chạy qua, được gấp thành hình vuông cạnh a = 10cm. Xác định vectơ cường độ từ trường tại tâm O của hình vuông.
Answer:
The net magnetic field ta the center of square is[tex]1.36\times10^{-4} T[/tex].
Explanation:
Current, I = 12 A , side ,a = 10 cm = 0.1 m
Let the magnetic field due to the one side is B.
The magnetic field is given by
[tex]B = \frac{\mu o}{4\pi}\times \frac{I}{r}\times \left (Sin A +Sin B \right )\\\\B = 10^{-7}\times \frac{12}{0.05}\times \left ( sin 45 + sin 45 \right )\\\\B = 3.4\times 10^{-5} T[/tex]
Net magnetic field at the center of the square is
B' = 4 B
[tex]B'= 4\times 3.4\times 10^{-5}\\\\B' = 1.36\times10^{-4} T[/tex]
Thermal physics vs atomic physics ...which is easier?
Answer:
Thermal physics
Explanation:
Because it uses temperature
Answer:
In my opinion both are easier if you'll work hard on it...
A cable car is being pulled up a mountain at 7.5 meters per second. Usually, the car takes 120 seconds to move all the way up the mountain. If its velocity stays constant, how much time will it take the cable car to move 39 meters?
Answer:
5.2 s
Explanation:
From the question given above, the following data were obtained:
Velocity = 7.5 m/s
Displacement = 39 m up
Time =?
The time taken for the cable cab to get to 39 m can be obtained as follow:
Velocity = Displacement / Time
7.5 = 39 / time
Cross multiply
7.5 × time = 39
Divide both side by 7.5
Time = 39 / 7.5
Time = 5.2 s
Thus, the time taken for the cable cab to get to 39 m up is 5.2 s
is retractable measuring tape a simple machine?
Answer:
A simple machine is a device that multiply an applied force by the use of the mechanical advantage built into the machine. Therefore, a simple machine changes the direction in which the applied force acts or the magnitude of the applied force, or both in order to do work
A retractable measuring tape is a device used for length measurement such that the direction of the applied force is reversed during retraction, while the magnitude of the output force is constant and dependent on the coil in the measuring
Therefore, the measuring tape does not have a constant mechanical advantage or act as a force multiplier, and therefore;
It is not a simple machine
Explanation:
NEED ANSWER QUICK, WILL GIVE BRAINLIEST! How many nails do sapiens have?
A. 6
B. 10
C. 3
D. None
Answer:
nice calculations!
Explanation:
Molten iron has a density of 7.0 g/cm. In its solid state, iron has a density of
8.0 g/cm?
Calculate the volume of 10 kg of molten iron.
Volume =
Which of the following is an elastic collision?
A.
A wad of gum sticking to a window
B.
Two cars colliding and sticking together
C.
A vase falling to the floor and shattering
D.
A tennis racquet hitting a ball
Answer: D
Explanation:
An elastic collision is a collision in which there is no net loss in kinetic energy in the system as a result of the collision. Both momentum and kinetic energy are conserved quantities in elastic collisions. Suppose two similar trolleys are traveling toward each other with equal speed.
Seeing these new artifically designed creatures at home, as the result of breeding, he coined the term ____ ______ to explain the variation of species around the islands and (by extension of his theory) also around the world.
Answer: Artificial Selection
Explanation: Artificial Selection is described as the identification of desirable traits in both plants and animals, then enhance them, so that those traits can be manifested in future generations.
This is the scope behind cross breeding of plants and animals and this have largely been used in agricultural sector to improve input (such as disease-resistant seeds) and other biotechnological settings.
Darwin's described artificial selection as the human form of natural selection.
The vine has a fixed end, so Tarzan's path is circular. So the vine must not only support Tarzan's weight (or some component of it) but must also provide centripetal force to curve Tarzan's velocity. At Tarzan's lowest point, this can be expressed as:_________.
Answer: hello your question lacks some data attached below is the missing data
answer : T - mg = ma[tex]_{c}[/tex]
Explanation:
Given that the vine has a fixed end and Tarzan's path is circular
At Tarzans lowest point the point can be expressed as shown below.
It can be expressed as : T - mg = ma[tex]_{c}[/tex]
A motorcycle daredevil plans to ride up a 2.0-m-high, 20∘ ramp, sail across a 10-m-wide pool filled with hungry crocodiles, and land at ground level on the other side. He has done this stunt many times and approaches it with confidence. Unfortunately, the motorcycle engine dies just as he starts up the ramp. He is going 10.4 m/s at that instant, and the rolling friction of his rubber tires (coefficient 0.02) is not negligible. Part A: Justify your answer by calculating the distance he travels through the air after leaving the end of the ramp.
Answer:
The motorcycle daredevil does not sail across the 10-m wide pool filled with hungry crocodiles
Explanation:
The given parameters are;
The height of the ramp = 2.0 m-high
The angle of elevation of the ramp, θ = 20°
The width of the pool = 10 m
The speed with which he is going when the engine fails = 10.4 m/s
The rolling friction between the rubber tires, μ = 0.02
μ·g·cos(θ) = (1/2)·(a)
a = (μ·g·cos(θ))/(1/2)
Where;
a = The acceleration down the plane
∴ a = 0.02 × 9.81 × cos(20°)/(1/2) ≈ 0.369
The length of the ramp, l = 2.0 m/(sin(20°)) ≈ 5.8476088 m
The velocity at the end of the ramp, v² = u² - 2·a·l
∴ v² = 10.4² - 2×(0.369 + 9.81 × sin(20°))×5.8476088 ≈ 64.60446471
v ≈ √(64.60446471) ≈ 8.04
∴ The velocity at the top of the ramp, v ≈ 8.04 m/s
The time it takes the motorcycle to reach ground level from the top of the ramp, t, is given as follows;
h = h₀ + u·t + (1/2)·a·t²
h₀ = 2, u = 8.04×sin(20°), a = -9.81
When h = 0 (ground level), we have;
∴ h = 2+ 8.04×sin(20°)·t - (1/2)×9.81×t²
0 ≈ 2.75·t - 4.905·t² + 2
2.75·t - 4.905·t² + 2 = 0
By using a graphing calculator, we have, t = 0.978 or t = -0.42
At ground level, the time of flight, t ≈ 0.978 s
The horizontal distance the motorcycle travels, before landing, x = u × cos(θ) × t
∴ x = 8.04×cos(20 Degrees) × 0.978 = 7.3889
The horizontal distance the motorcycle travels, before landing, x ≈ 7.3889 m
Therefore, given that the horizontal distance the motorcycle travels in the air 7.3889 m < 10 m, therefore the motorcycle daredevil does not sail across the 10-m wide pool filled with hungry crocodiles
If a 60 W light bulb and a 75 W light bulb operate from 150 V source, which bulb has a greater current in it?
60 W
75 W
Answer:
Since it us the resistance that causes the power output, it might be intuitive to think that more resistance produces more power but as P=I^2 * R one actually needs high current and low resistqnce. That means 75 W has lower resistance and higher current.
Now you may think that making the resistance very low, one gets the most power. Not so, as the circuit has wires, power source etc. All the have their resistance. In theory one gets the maximum power over a resistor when the resistor is half of the total resistance of the circuit. This in practice would be inefficient as one would lose half of the total power elsewhere. In practice circuits have fuses that limit the current and one gets the maximum power at the current the fuse is rated to. So if there is 20 A fuse, the maximum power is 2400 W and the corresponding resistance 6 ohm.
An ohmic dipole of resistance 100 ohm is crossed by a current of intensity 120 ma. Calculates the voltage across this chemical dipole
Answer:
12.0 Volt
Explanation:
Step 1: Given data
Resistance of the ohmic dipole (R): 100 Ohm
Intensity of current (I): 120 mA (0.120 A)
Step 2: Calculate the voltage (V) across this chemical dipole
To calculate the voltage across the ohmic dipole, we will use Ohm's law.
I = V/R
V = I × R
V = 0.120 A × 100 Ohm = 12.0 V
1. explain why nichrome wire used in the heater.
2. explain why copper wire not used in the heater.
Answer:
1. The reason why nichrome wire is used in a heater is due to the properties of nichrome which makes it a material of choice for heating application including;
i) The cost of manufacture of nichrome is low
ii) Nichrome has both high mechanical and creep strength, and therefore is suitable for installation and use in a wide setting
iii) Nichrome has a high resistance to electron flow, making it a good electrical heating element
iv) Nichrome has a high resistance to oxidation, such that it can be reused several times as a heater
v) The high ductility of nichrome allows it to be stretched and drawn around different vessels with contents to which heat is to be supplied
2. Copper wire is not used in heaters because according to Joule's law, the heat produced from the flow of electric current, 'I', through a material having a resistance, 'R', for a time, 't', is proportional to I²·R·t, and copper has a very low resistance, 'R', to the flow of electric current, and therefore, will not produce sufficient heat required at a given current level
Explanation:
The density of dry air at room temperature and atmospheric pressure Is 1.2 kg m-3. What volume would 6 kg of dry air occupy under these conditions?
Answer:
V = 5 m³
Explanation:
The density of air, d = 1.2 kg/m³
Mass of the dry air, m = 6 kg
We need to find the volume o the gas. We know that, the density of an object is given by mass divided by its volume. So,
[tex]d=\dfrac{m}{V}\\\\V=\dfrac{m}{d}\\\\V=\dfrac{6}{1.2}\\\\V=5\ m^3[/tex]
So, the volume of the dry air is 5 m³.
If youre walking from point a to b, the magnitude of your displacement will always be equal or less than or greater than your distance?
The magnitude of your displacement can be equal to the distance you covered, or it can be less than the distance you covered. But it can never be greater than the distance you covered.
This is because displacement is a straight line, whereas distance can be a straight line, a squiggly line, a zig-zag line, a line with loops in it, a line with a bunch of back-and-forths in it, or any other kind of line.
The straight line is always the shortest path between two points.
At what point will the electric field of a charged object be strongest?
A where the electric field lines are perpendicular to the equipotential line
B. where the electric field lines are farthest apart
C. where the electric field lines are closest together
D. where the electric field lines are parallel to the equipotential line
Answer:
The answer is C because they have to be close to be able to interact
Answer:
C. where the electric field lines are closest together
Explanation:
300kg of water are lifted 10m vertically in 5s show the work done in 30kj and that power is 6kw . Please help me
Answer:
6KW
Explanation:
The computation is shown below:
We know that
Work done= m ×g× h
Here
W= 300×10×10
= 30000 J
= 30 KJ
And
Power= Work done ÷time taken
P = 30000 ÷ 5
= 6000W
= 6KW
The above represent the answer
How much gravitational potential energy does an object have if it is located 20 m above the point that we define as O height and has a mass of 10 kg
Answer:
Explanation:
PE = mgh where m is the mass in kg, g is the pull of gravity which is 9.8, and h is the height of the object above the point to which it could possibly fall, measured in meters. Plugging in:
PE = 10(9.8)(20) so
PE = 1960 J
This should be rounded to 1 sig fig according to the rules of sig fig and your numbers here, but I imagine you're not following them all that much. It should be 2000 J
can someone please help
The answer is B. Mono and polyunsaturated fats because the other two are really harmful and they are not healthy whatsoever.
A force of 30.0 N is applied to a 3.00 kg object for 3.00 seconds. Calculate the velocity experienced by the object.
Answer:
Explanation:
F = ma and
[tex]a=\frac{v}{t}[/tex]
We have F, we have m, but in order to solve for v, we need a.
30.0 = 3.00a so
a = 10.0 m/s/s. Plug that in for a in the second equation and solve for v:
[tex]10.0=\frac{v}{3.00}[/tex] so
v = 10.0(3.00) so
v = 30.0 m/s
What would be the weight (in Newtons) of a person with a mass of 80 kg on Earth, where the acceleration due to gravity is approximately 9.8 m/s/s? *
please help asap
Answer:
ml tayo 1v1 durugin kita
Explanation:
ano takot ml 1v1
How much force is required (in Newtons) to accelerate a 12-kg bicycle, along with its 50-kg rider, at 2 m/s2?
Give your answer as a number.
Answer:
F = 124 N
Explanation:
Given that,
The mass of bicycle and the rider, m = 12 kg + 50 kg = 62 kg
Acceleration of system, a = 2 m/s²
We need to find the force required to accelerate the system. We know that,
Net force, F = ma
Put all the values,
F = 62 kg × 2 m/s²
F = 124 N
So, the required force is equal to 124 N.
As a train starts from rest then accelerates down the track, coming toward an observer faster and faster, the frequency of the sound waves coming toward the observer will be
Answer:
Increase in frequency constantly
Explanation:
This concept can be explained by Doppler shift as per which any form of disturbance spreads out spherically from its point of origin. If the source of sound wave is stationary and the receiver is also stationary, then the frequency remains the same but if the source is moving, then the disturbance caused is closer on one side and distant on the other side thereby producing shorter wavelength in direction the source is moving and longer wavelength in the opposite direction.
What produces magnetic fields?
Answer:
flowers
Explanation:
i'm really not sure but i have this gut feeling its flowers
Marcel and Jose lifted 50 pounds as many times as they could. Marcel could lift the weight 25 times. Jose could lift the weight 30 times. Marcel and Jose can conclude that __________.
A.
Jose has better muscular endurance than Marcel
B.
Jose has better muscular strength than Marcel
C.
Marcel has better muscular strength than Jose
D.
Marcel has better muscular endurance than Jose
Answer:
A
Explanation:
Date:
Page:
# Excercise.
7.
A very short answer questions.
what is acceleration due to gravity? what is
value of 'g’ on equatorial region and
polar region of the earth?
the
Answer:
See the answer below
Explanation:
Acceleration due to gravity (g) is the accelerational force experienced by a body as a result of the influence of the earth's gravitational force. It is a vector quantity, that is, it has both magnitude and direction.
The acceleration due to gravity is inversely proportional to the square of the radius of the earth. Hence, g at the equatorial region is slightly lesser (9.780 m/s2) than that of the polar regions (9.832 m/s2) of the earth because the earth bulges at the equator leading to a higher radius than at the poles.
Daniel wants to find out if he can notice the difference in light intensity when he adds some lit candles to a set of 50 lit candles. When he adds 5 candles to the set, he notices the difference in intensity half the time. However, when he adds less than 5 candles to his set, he does not notice any difference in the intensity of light. In this scenario, Daniel's difference threshold for detecting the change in light intensity is ________ lit candles.
Answer:
5
Explanation:
The light intensity may be defined as the strength of the light or the magnitude of its brightness that a source of light can produce.
The light threshold is the minimum intensity of the light that our eye can detect and the ability to adapt to darkness.
In the context, Daniel wishes to find if can notice the difference in the intensity of the light when he add 5 candles to the set of 50 candles.
He noticed that when he added 5 candles, he could notice the difference in the intensity and when he added less than 5 candles to the set of 50 candles he could not detect.
Thus, the difference threshold for Daniel to detect the change in the intensity of the light is 5 candles.
3.
The mass of a regulation tennis ball is 57 g. Typically during a serve the ball is in contact with the tennis racket for 30 ms. If the serve
was measured at 73.14 m/s what impulse was exerted on the tennis ball?
5.5 kg. m/s
7.8 kgm/s
2.3 kg. m/s
4.2 kg. m/s
Một dây dẫn mảnh được uốn thành một cung tròn bán kính 10cm, góc ở tâm bằng 1200, đặt trong không khí. Trong dây dẫn có dòng điện cường độ 30A chạy qua. Độ lớn của cảm ứng từ tại tâm của cung tròn là bao nhiêu ?
Answer:
Diana and that
Explanation:
muyayyano
The flow chart shows the life cycle of a star. Was this star smaller than our sun, about the same or bigger than our sun?
1. Bigger
2. About the same
3. Smaller
The star is bigger than our sun. The correct option is 1.
The flow chart of the life cycle of a star indicates that the star starts as a nebula, which is a cloud of gas and dust. The nebula can collapse due to gravitational forces and form a protostar. The protostar can then continue to contract and heat up until it reaches a temperature and density at which nuclear fusion can occur, leading to the star entering the main sequence phase.
The size of a star is determined by its mass, and the more massive a star is, the bigger it will be. Based on this information, we can infer that if a star follows the life cycle shown in the flow chart, starting from a nebula and eventually reaching the main sequence, it must be at least as massive as our sun or even more massive, since only stars with sufficient mass can become main sequence stars.
To learn about the heliocentric model of the Solar System click:
https://brainly.com/question/12075871
#SPJ2
