A typical radio frequency is 99.5 MHz, while a HD TV broadcast frequency is 600 MHz. Which one is your body position more likely to interfere with and why

E= [tex]\frac{1}{2}[/tex]×k×x² = 1J

given k=800n/m x=0.05m

Answer:

a) 91 m/s

b) 111 m/s

Explanation:

v = u + at

v = 128sin60 + (-9.8)(2.0) = 91.25125... m/s

v = √(vx² + vy²) = √((128cos60)² + 91.25125²) = 111.4575... m/s

Answer:

Explanation:

The best way to do this is to remember the rule about the halfway mark in a parabolic path. At a trajectory's half way point in its travels, it will be at its max height. To get the total time in the air, we take that time at half way and double it. Here's what we know that we are told:

initial velocity is 20 m/s

Here's what we know that we are NOT told:

a = -9.8 m/s/s and

final velocity is 0 at an object's max height in parabolic motion.

We will use the equation:

[tex]v=v_0+at[/tex] where v is final velocity and v0 is initial velocity. Filling in:

0 = 20 + (-9.8)t and

-20 = -9.8t so

t = 2 seconds. The stone reaches its max height 2 seconds after it is thrown; that means that after another 2 seconds it will be on the ground. Total air time is 4 seconds.

Answer:

(A) Gravity is you're answer.

Explanation:

When an object or human is falling at an increased rate, The force of gravity is taking place.

Answer:

The rate of doing work is called power.

Answer:

The amount of energy transported or transformed per unit time is referred to as power in physics. The watt, which is equal to one joule per second in the International System of Units, is the unit of power.

OAmalOHopeO

Answer:

simultaneously

Time taken to reach the ground depends on the vertical component of velocity, not horizontal component of velocity.

Answer:

(a) The self inductance, L = 21.95 mH

(b) The energy stored, E = 4.84 J

(c) the time, t = 0.154 s

Explanation:

(a) Self inductance is calculated as;

[tex]L = \frac{N^2 \mu_0 A}{l}[/tex]

where;

N is the number of turns = 1000 loops

μ is the permeability of free space = 4π x 10⁻⁷ H/m

l is the length of the inductor, = 45 cm = 0.45 m

A is the area of the inductor (given diameter = 10 cm = 0.1 m)

[tex]A = \pi r^2 = \frac{\pi d^2}{4} = \frac{\pi \times (0.1)^2}{4} = 0.00786 \ m^2[/tex]

[tex]L = \frac{(1000)^2 \times (4\pi \times 10^{-7}) \times (0.00786)}{0.45} \\\\L = 0.02195 \ H\\\\L = 21.95 \ mH[/tex]

(b) The energy stored in the inductor when 21 A current ;

[tex]E = \frac{1}{2}LI^2\\\\E = \frac{1}{2} \times (0.02195) \times (21) ^2\\\\E = 4.84 \ J[/tex]

(c) time it can be turned off if the induced emf cannot exceed 3.0 V;

[tex]emf = L \frac{\Delta I}{\Delta t} \\\\t = \frac{LI}{emf} \\\\t = \frac{0.02195 \times 21}{3} \\\\t = 0.154 \ s[/tex]

Answer:

wegkwe fhkrbhefdb

Explanation:B

One of the two requirements of electric current is there must be an electric potential between two bodies

For electric current to flow, there must be an electric potential between two bodies.

This is because electric charge flows from a higher electric potential to a lower electric potential just as, water flows from a higher gravitational potential to a lower gravitational potential.

The difference between the electric potential between the two bodies causes the electric charge to flow between the two bodies.

This flow of electric charge constitutes electric current and electric current will only flow when there is an electric potential between two bodies.

So, one of the two requirements of electric current is there must be an electric potential between two bodies.

So, the answer is A

Learn more about electric current here:

https://brainly.com/question/13562393

Answer:

a) Fnet = mg - Fb - Fr

b) 8.67 secs

Explanation:

mass of object = 80 kg

Buoyancy force = 1/50 * weight ( 80 * 9.81 ) = 15.696

Proportionality constant = 10 N-sec/m

a) Calculate  equation of motion of the object

Force of resistance on object  due to water = Fr ∝ V

                                                                         = Fr = Kv = 10 V

Given that : Fb( due to buoyancy ) , Fr ( Force of resistance ) acts in the positive y-direction on the object  while mg ( weight ) acts in the negative y - direction on the object.

Fnet = mg - Fb - Fr

∴ Equation of motion of the object ( Ma = mg - Fb - Fr )

b) Calculate how long before velocity of the object hits 40 m/s

Ma = mg - Fb - Fr

a = 9.81 - 0.1962 - 0.125 V = 9.6138 - 0.125 V

V = u + at ---- ( 1 )

u = 0

V = 40 m/s

a = 9.6138 - 0.125 V

back to equation 1

40 = 0 + ( 9.6138 - 0.125 (40) ) t

40 = 4.6138 t

∴ t = 40 / 4.6138 = 8.67 secs

Answer:

The torque decreases because as the hanging mass goes down, the moment arm about the pivot point decreases. Since the torque is directly proportional to the length of the moment arm, torque decreases.

The torque decreases because as the hanging mass goes down, the moment arm about the pivot point decreases. Since the torque is directly proportional to the length of the moment arm, torque decreases.

Atomic number of an element  is defined as total number of protons present in the nucleus,  neutrons carry no net electrical charge, so it is the charge number of the nucleus.

atomic mass of an element can be defined as the atomic weight is measured total mass of an element’s atom, the total number of neutrons and protons in the nucleus of an atom.

Both Atomic mass and an atomic number of elements are closely related if  atomic number is high, then the atomic mass is also said to be high.

For more details regarding fire mass , visit

brainly.com/question/16858932

#SPJ2

We have that  the ratio of his walking pace  to the walking pace of a person of average height is

[tex]\frac{V_2}{V_1}=1.10[/tex]

given the assumption and the calculation given below

From the question we are told that:

Consider a person 18\% shorter than average

Let average height of a person be [tex]10m[/tex]

Therefore

The height of an [tex]18\%[/tex] shorter man is mathematically given as

H=10*0.18

H=8.2m

Generally, the equation for velocity is mathematically given by

[tex]v=\frac{1}{2\pi} \sqrt{{g}{l}}[/tex]

Where we have the  Assumption that a person's leg swings like a pendulum and that the angular amplitude of everybody's stride is about the same

Therefore

[tex]\frac{V_1}{V_2}=\frac{l_1}{l_2}[/tex]

[tex]\frac{V_1}{V_2}={82}{100}[/tex]

[tex]\frac{V_2}{V_1}=1.10[/tex]

In conclusion

The ratio of his walking pace (that is, the frequency 'f' of his motion) to the walking pace of a person of average height is

[tex]\frac{V_2}{V_1}=1.10[/tex]

For more information on this visit

https://brainly.com/question/21196186

Answer:

Explanation:

F = ma

F = (10)(3)

F = 30 N

Answer:

[tex]\boxed {\boxed {\sf 30 \ Newtons}}[/tex]

Explanation:

We are asked to find the applied net force. According to Newton's Second of Law, force is the product of mass and acceleration.

[tex]F= m \times a[/tex]

The object has a mass of 10 kilograms and it is accelerating at 3 meters per second squared.

Substitute the known values into the formula.

[tex]F= 10 \ kg \times 3 \ m/s ^2[/tex]

Multiply.

[tex]F= 30 \ kg \times m/s^2[/tex]

1 kilogram meter per second squared is equal to 1 Newton, so our answer of 30 kg × m/s² is equal to 30 N.

[tex]F= 30 \ N[/tex]

The applied net force is 30 Newtons.

Answer:

tables, charts and graphs

Explanation:

Answer:

I = 15,645. kg*m/s or 15,645 N*s

Explanation:

I = m(^v)

I = 1050kg((26.2m/s-11.3m/s)

I = 15,645. kg*m/s

Answer:

B 5s

Explanation:

Because of the Displacement in the nth second of the free fall is 

Snth=21g(t12−t22)

Given that (tn−tn−1)=1

Displacement in 3 seconds of the free fall 

S=21gt2

S=21×10×32

S=45m

Given that: Snth=45

On solving that we get:

t1=5sec

The answer is 40 kg. m/s.

Formula for momentum:

p=mv

p=(10 kg.)(4 m/s)

So, therefore, the final answer is p=40 kg. m/s.

I hope this helped answer your question. Enjoy your day, and take care!

Answer: its 400 n/s

Explanation:

cus my thing said it was right

Answer:

Level 1-

1. It depends of the sense and the magnitude of the force

2. Electric force

3. A contact force need to touch to act in the object, like push a box for example. A non-contact force don't need to touch to act in the object, like an magnet attracting other magnet

4. The pressure is the force divided by the area. The unit for pressure in the international system is Pascal

5. Because the pressure is applied in all the surface of our bodies, so the force is divided by the surface area of our bodies.

Level 2-

1. The balloons stick to the walls because when she rubbed they in her clothes they earned eletric charge, and when they touched the wall, the electric charges of the wall got polarized and it creats a attraction force.

The same happened with the water stream. The balloons were charged with electric charges and the water was attracted by it.

2. Mass is the amount of matter, it's an scalar quantity. Weight is the force created by the attraction of a massive body as the Earth, and another body as a human, and a force is a vector

3. It's for increase the surface area, so the pressure will be decreased

4. When a person pulls up the syringe plunger the pressure inside the syringe is smaller than the pressure outside, so the pressure push the liquid into the syringe

5. a) The stream of the top is falling closer than the stream from the bottom, causa in the top the pressure is lower than in the bottom. In the bottom, beyond the air pressure, it has also the whole column of water making more pressure, so it goes far.

b) The streams are all near because the holes are in the same height, so the pressure is divided for all the holes.

Level 3-

1. The girl.

pressure of the girl: 50/1 = 50

pressure of the man: 100/25 = 4

pressure of the elephant: 4500/250 = 18

So, the girl exerts more pressure.

2. When the can is heated the air inside expands and get out of it. If you seal the mouth of the can, the air cannot return to inside it, and when it get colder the air inside will shrink back to the normal volume, so it will occupy less space and the outside pressure will exerts a force and deform the can.

Answer:

Because it is the result of two more fundamental units, a derived unit is termed that. For volume, the cubic meter (m³) is the fundamental unit of area. Any number that cannot be measured directly with any equipment is referred to as a derived unit. For example, we can't quantify a substance's density using a rule, scale, or bucket.

OAmalOHopeO

a) y(max)  = 337.76 m

b) t₁ = 5.30 s  the time for y maximum

c)t₂ =  13.60 s  time for y = 0 time when the fly finish

d) vₓ = 30 m/s        vy = - 81.32 m/s

e)x = 408 m

Equations for projectile motion:

v₀ₓ = v₀ * cosα          v₀ₓ = 60*(1/2)     v₀ₓ = 30 m/s   ( constant )

v₀y = v₀ * sinα           v₀y = 60*(√3/2)     v₀y = 30*√3  m/s

a) Maximum height:

The following equation describes the motion in y coordinates

y  =  y₀ + v₀y*t - (1/2)*g*t²      (1)

To find h(max), we need to calculate t₁ ( time for h maximum)

we take derivative on both sides of the equation

dy/dt  = v₀y  - g*t

dy/dt  = 0           v₀y  - g*t₁  = 0    t₁ = v₀y/g

v₀y = 60*sin60°  = 60*√3/2  = 30*√3

g = 9.8 m/s²

t₁ = 5.30 s  the time for y maximum

And y maximum is obtained from the substitution of t₁  in equation (1)

y (max) = 200 + 30*√3 * (5.30)  - (1/2)*9.8*(5.3)²

y (max) = 200 + 275.40 - 137.64

y(max)  = 337.76 m

Total time of flying (t₂)  is when coordinate y = 0

y = 0 = y₀  + v₀y*t₂ - (1/2)* g*t₂²

0 = 200 + 30*√3*t₂  - 4.9*t₂²            4.9 t₂² - 51.96*t₂ - 200 = 0

The above equation is a second-degree equation, solving for  t₂

t =  [51.96 ±√ (51.96)² + 4*4.9*200]/9.8

t =  [51.96 ±√2700 + 3920]/9.8

t =  [51.96 ± 81.36]/9.8

t = 51.96 - 81.36)/9.8         we dismiss this solution ( negative time)

t₂ =  13.60 s  time for y = 0 time when the fly finish

The components of the velocity just before striking the ground are:

vₓ = v₀ *cos60°       vₓ = 30 m/s  as we said before v₀ₓ is constant

vy = v₀y - g *t        vy = 30*√3  - 9.8 * (13.60)

vy = 51.96 - 133.28         vy = - 81.32 m/s

The sign minus means that vy  change direction

Finally the horizontal distance is:

x = vₓ * t

x = 30 * 13.60  m

x = 408 m

Explanation:

Those tools that helps to make our work easier ,faster and more convenient in our daily life it is called simple Machine.

Answer:

Both will have the same momentum.

P = M v     momentum

v = a t   for uniform acceleration

P = M a t

But a = F / M

P = M (F / M) t = F t    so both have the same momentum

Answer:

[tex]F=133N[/tex]

Explanation:

From the question we are told that:

Length [tex]l=3.0m[/tex]

Mass [tex]m=24kg[/tex]

Distance from Tip [tex]d=35cm[/tex]

Generally, the equation for Torque Balance is mathematically given by

[tex]mg(l/2)=F(l-d)[/tex]

[tex]2*9.81(3/2)=F(3-35*10^-2)[/tex]

Therefore

[tex]F=133N[/tex]

Answer:

just need some focus

Explanation:

tan 13. The speed of a horse is 134 meters per second how long does it take to travel a distance of 19,311m? M+ tud V 134 14. You are walking down the block and see your neighbor's pitbull 30 meters away, out of the fence, starring at you. Suddenly, he starts running towards you at 20m/s. How long will it be before you're the pitbull's lunch?  V 15. A pendulum has a frequency of 2 Hz what is it's period. T = 1/2 16. You have just finished a 1600 mile trip, and it took you 16 hours. What was your average speed V = Ad At 17. You are flying from New York, NY to SanFrancisco California, a distance of 2582 miles, it takes 6.33hrs to complete the flight what was your average speed? give answer in m/s. V = Ad = At 3 of 6

Answer:

şen çal kapimi turkish drama

Answer:

[tex]u=34cm[/tex]

Explanation:

From the question we are told that:

Far point is [tex]V=34 cm[/tex]

Near point is [tex]u=17 cm[/tex]

Therefore

Focal Length

[tex]f=-34cm[/tex]

Generally the equation for the Lens is mathematically given by

[tex]\frac{1}{u}=\frac{1}{f}-\frac{1}{v}[/tex]

[tex]\frac{1}{u}=\frac{1}{-34}-\frac{1}{-17}[/tex]

[tex]u=34cm[/tex]

Answer:

a)   R₁ = 14.1 Ω,   b)  R₂ =  19.9 Ω

Explanation:

For this exercise we must use ohm's law remembering that in a series circuit the equivalent resistance is the sum of the resistances

all resistors connected

           V = i (R₁ + R₂)

with R₁ connected

           V = (i + 0.5) R₁

with R₂ connected

           V = (i + 0.25) R₂

We have a system of three equations with three unknowns for which we can solve it

We substitute the last two equations in the first

           V = i ( [tex]\frac{V}{ i+0.5} + \frac{V}{i+0.25}[/tex] )

           1 = i ( [tex]\frac{1}{i+0.5} + \frac{1}{i+0.25}[/tex] )

           1 = i ( [tex]\frac{i+0.5+i+0.25}{(i+0.5) \ ( i+0.25) }[/tex] ) =  [tex]\frac{i^2 + 0.75i}{i^2 + 0.75 i + 0.125}[/tex]

           i² + 0.75 i + 0.125 = 2i² + 0.75 i

           i² - 0.125 = 0

           i = √0.125

           i = 0.35355 A

with the second equation we look for R1

          R₁ = [tex]\frac{V}{i+0.5}[/tex]

          R₁ = 12 /( 0.35355 +0.5)

          R₁ = 14.1 Ω

with the third equation we look for R2

          R₂ = [tex]\frac{V}{i+0.25}[/tex]

          R₂ =[tex]\frac{12}{0.35355+0.25}[/tex]

          R₂ =  19.9 Ω

Answer:

B. Increases.

Explanation:

[tex]{ \bf{F = \frac{m {v}^{2} }{r} }} \\ { \bf{F \: \alpha \: {v}^{2} }}[/tex]

Keeping mass, and radius constant, speed or velocity is directly proportioanal to centripetal force.

,In order to increase the speed of an object on a circular path, YOU have to increase the centripetal force acting on it.

The value of the acceleration is a = 0.5 m/s². The position at 80 s is x = 3200 m and finally the average velocity is v = 40 m/s.

Acceleration:

We can use the fallowing kinematic equation to get the acceleration at 80 s.

[tex]a=\frac{v_{f}-v_{i}}{t}[/tex]            

Where:

The, we have:

[tex]\vec{a}=\frac{60-20}{80}[/tex]

[tex]\vec{a}=0.5\: m/s^{2}[/tex]

Position:

Knowing the acceleration we can find the position using the falling equation.

[tex]\vec{x}=v_{i}t+0.5at^{2}[/tex]

[tex]\vec{x}=20*80+0.5*0.5*80^{2}[/tex]

[tex]\vec{x}=3200 m[/tex]

Average velocity:

The definition of the average velocity is:

[tex]\vec{v}=\frac{\Delta x}{t}[/tex]

[tex]\vec{v}=\frac{x_{f}-x_{i}}{t}[/tex]

[tex]\vec{v}=\frac{3200-0}{80}[/tex]

[tex]\vec{v}=40\: m/s[/tex]

Learn more about the kinematic equations here:

https://brainly.com/question/13143668

I hope it helps you!