A therm is a unit of measure for gas. Mrs Schertz’ natural gas usage was 74 therms for the month of March. 49 therms were charged at the baseline charge of $0.74/therm and 25 therms were charged at over baseline charge of $0.98 per therm.
a) What was the total price of the natural gas for the month?
b) There are 4 people living in her home. How many therms per capita?

Answers

Answer 1
The total price of natural gas for the month was $60.76.The therms per capita for Mrs. Schertz's household is 18.5 therms per person.

How to calculate for total price of natural gas for the month?

To calculate the total price of natural gas for the month, we need to multiply the number of therms charged at the baseline rate by the baseline rate and the number of therms charged at the over baseline rate by the over baseline rate, and then add these two amounts together.

So, the total cost of natural gas for the month is:

49 therms x $0.74/therm + 25 therms x $0.98/therm

=  $36.26 + $24.50 = $60.76

Therefore, the total price of natural gas for the month was $60.76.

To calculate the therms per capita, we need to divide the total number of therms used by the number of people living in Mrs. Schertz's home.

So, the therms per capita is:

74 therms / 4 people = 18.5 therms/person

Therefore, the therms per capita for Mrs. Schertz's household is 18.5 therms per person.

Learn about per capita here https://brainly.com/question/2041857

#SPJ1


Related Questions

please help!!
If an object were in motion, how might you use a magnet to change the direction of its motion? Diagram the setup and explain your reasoning.​

Answers

If the object in motion has some magnetic properties or contains a magnet, we can use another magnet to change its direction of motion by exerting a force on it through magnetic interaction. This principle is known as the Lorentz force.

Here's how we can set up the experiment:

Take a magnet and place it on a flat surface.

Take another magnet or the object with magnetic properties that is in motion.

Hold the magnet or the object in your hand and bring it close to the stationary magnet without touching it.

Move the magnet or the object towards the stationary magnet and observe its behavior.

If the magnet or the object has the same polarity as the stationary magnet, they will repel each other, and the motion of the object will be deflected in a direction away from the stationary magnet. If the magnet or the object has opposite polarity to the stationary magnet, they will attract each other, and the motion of the object will be deflected in a direction towards the stationary magnet.

Here's a diagram to help you visualize the setup:

                 N   S          N   S

       __________    __________

      |                       |  |                     |

      |   M1               |  |           M2     |

      |__________|  |__________|

              ( )                             ( )

               |                               |

        Motion              Stationary

        Object                 Magnet

In this diagram, M1 represents the motion object or magnet, and M2 represents the stationary magnet. The N and S represent the North and South poles of the magnets. The arrows indicate the direction of motion and the direction of the magnetic field.

As we move M1 towards M2, the magnetic interaction will exert a force on M1, causing it to change its direction of motion. The direction of deflection will depend on the polarity of the magnets.

Note: It's important to keep in mind that the magnetic force is only one of the many factors that can affect the motion of an object. Other factors such as friction, air resistance, and gravitational forces can also play a significant role.

To know more about  Motion visit :-

https://brainly.com/question/453639

#SPJ1

A light ray travels from air (n = 1. 0) into water (n = 1. 33). The angle of incidence is 34°. What is the angle of refraction?

Answers

Snell's Law, which states that the ratio of the indices of refraction of the two media is equal to the ratio of the sines of the angles of incidence and refraction, can be used to resolve this issue:

n1 sin - 1 = n2 sin - 2 where n1 is the initial medium's index of refraction (air) The second medium's index of refraction is given by n2 (water Angle of incidence = 1 Angle of refraction = 2 (what we want to find) With the values from the problem substituted, we obtain: 1.00 sin 34° = 1.33 sin θ₂ Solving for 2 gives us: 1.00 sin 34° / 1.33 25.9° = 2 = sin In light of this, the angle of refraction is roughly 25.9°. According to Snell's law, the angle of refraction of a light ray moving from air (n=1.0) into water (n=1.33) at an angle of incidence of 34° is roughly 23.8°.

learn more about refraction here:

https://brainly.com/question/14760207

#SPJ4

a rock of weight 500 n is at rest on the ground. the coefficient of static friction between the ground and the rock is 0.50. if someone pushes the rock with an applied force of 100 n to the right, what is the force of static friction between the ground and the rock?

Answers

The force of static friction between the ground and the rock is equal to the coefficient of static friction multiplied by the normal force. Since the rock is of weight 500 N, the normal force is 500 N. Therefore, the force of static friction is 500 N × 0.50 = 250 N.


What is the force of static friction?

The rock is at rest on the ground. The rock's weight is 500 N. The coefficient of static friction between the ground and the rock is 0.50. If somebody pushes the rock to the right with an applied force of 100 N.

In the present situation, we need to determine the force of static friction between the ground and the rock. The rock is not moving, and therefore the maximum static friction force is equal to the applied force of 100 N. To find the normal force (FN), we'll have to start with calculating the gravitational force acting on the rock.

The force of gravity is given as:

Fg = mg

where, m = mass of the object, g = acceleration due to gravity

The weight of the rock is given as 500 N. We can find the mass of the rock by dividing the weight by the acceleration due to gravity. Therefore,

m = Fg/g = 500 N / 9.81 m/s² = 50.9 kg

Now, we can compute the normal force (FN) exerted by the ground on the rock as:

FN = mg = 50.9 kg × 9.81 m/s² = 500 N

Therefore, FS ≤ μs FN= 0.50 × 500 N = 250 N

The maximum static friction force that can be exerted by the ground is 250 N. Therefore, the force of static friction between the ground and the rock is 100 N.

Read more about friction here:

https://brainly.com/question/24338873

#SPJ11

If you stand on one foot while holding your other leg up behind you, your muscles apply a force to hold your leg in this raised position. We can model this situation as in Figure 1). The leg pivots at the knee joint, and the force that holds the leg up is provided by a tendon attached to the lower leg as shown Assume that the lower leg and the foot have a combined mass of 3.6kg, and that the combined center of gravity is at the center of Figure he knot What is the magnitude of this force? The london provides you hold your leg in this position the upper legeerts a force Express your answer with the appropriate units the lower le TARO? Value Units Sube

Answers

To keep the leg in the raised position, the tendon should provide 160N force.

The rotating force or moment of a force around a particular axis or pivot point is measured by torque. The tendency of a force to cause an object to spin along an axis is described as a vector quantity, torque.

Given: combined mass of the lower leg and the foot, m = 3.6kg

position of the center of gravity, r1 = 25cm

r = 0.25m

distance between tendon and lower leg, r2 = 5cm = 0.05m

torque applied will be τ = 3.6 × 10 × 0.25

τ = 8 N-m

the force applied by tendon

F = τ/ r2

F = 8/ 0.05

F = 160N

Therefore, To keep the leg in the raised position, the tendon should provide 160N force.

To know more about torque, click here:

https://brainly.com/question/29024338

#SPJ12

Why are masses listed on the periodic table not whole #'s. Ex. 15.9999 for oxygen?​

Answers

The masses listed on the periodic table are not whole numbers because they represent the weighted average of all the naturally occurring isotopes of an element.

What are Isotopes ?

Isotopes are atoms of the same element that have different numbers of neutrons in their nuclei, resulting in slightly different masses. Since the abundance of each isotope in nature can vary, the weighted average takes into account the abundance of each isotope and their corresponding masses, resulting in a decimal value. For example, oxygen has three naturally occurring isotopes, with mass numbers of 16, 17, and 18.

Why only O-16 isotopes ?

The most abundant isotope is oxygen-16, but the other isotopes are also present in trace amounts, leading to a weighted average of 15.9994 amu (atomic mass units). This is why the mass listed on the periodic table for oxygen is 15.999, which is a rounded value of the weighted average.

To know more about isotopes , visit :

https://brainly.com/question/11680817

#SPJ1

The masses listed on the periodic table are not whole numbers because they represent the average atomic mass of all the naturally occurring isotopes of an element, taking into account their relative abundances.

What are isotopes ?

Isotopes are atoms of the same element that have different numbers of neutrons in their nucleus, which affects their atomic mass. Some isotopes of an element are more abundant than others, and their relative abundances are taken into account when calculating the average atomic mass.

For example, oxygen has three naturally occurring isotopes: oxygen-16, oxygen-17, and oxygen-18. Oxygen-16 is the most abundant isotope, making up about 99% of all oxygen atoms. Oxygen-17 and oxygen-18 are much less abundant, but they still contribute to the overall atomic mass of the element.

The atomic mass listed on the periodic table for oxygen (15.9994) is the weighted average of the atomic masses of all three isotopes, taking into account their relative abundances. This average is not a whole number because the isotopes have different atomic masses and abundances, and their contributions to the overall average are weighted accordingly.

To know more about Periodic table visit :-

https://brainly.com/question/1173237

#SPJ1

Suppose you watch a leaf bobbing up and down as ripples pass it by in a pond. You notice that it does two full up and down bobs each second. Which statement is true of the ripples on the pond?
They have a frequency of 2 hertz.

Answers

The correct statement of the ripples on the pond is that they have a frequency of 2 hertz.

In physics, the number of cycles of a periodic wave that occur in a unit of time is known as the frequency of that wave. Its unit is hertz (Hz), which indicates cycles per second.A hertz is a unit of frequency that indicates how many times per second a wave oscillates. The amount of time it takes for one complete cycle of the wave is inversely proportional to its frequency. A wave with a high frequency oscillates more frequently than one with a low frequency.What is hertz (Hz)?Hertz (Hz) is the standard unit of frequency. One hertz (Hz) is equal to one cycle per second, meaning that a wave with a frequency of 2 Hz repeats twice in one second. Therefore, the frequency of the ripples on the pond is 2 hertz.

More on frequency: https://brainly.com/question/25811461

#SPJ11

An apple fell 6.0 m from a tree to the ground. What additional information is needed to calculate both the gravitational potential energy of the apple and its kinetic energy?

the volume of the apple and the time the apple was in the air
the mass of the apple and the amount of energy lost to air resistance
the average acceleration of the apple and the time the apple was in the air
the average velocity of the apple and the amount of energy lost to friction

Answers

For calculation of potential energy mass of the apple , average acceleration of the apple and height of apple is required.

Energy While for calculation of kinetic energy volume of the apple and time the apple was in air, the average velocity of the apple and amount of energy lost to friction is required.Based on the force exerted on the two objects, the potential energy equation is determined. P.E. = mgh, where m is the mass in kilograms, g is the acceleration caused by gravity (9.8 m/s2 at the earth's surface), and h is the height in meters, is the formula for gravitational force.The relationship between kinetic energy and an object's mass and squared velocity is given by K.E. = 1/2 m v2. If the mass is measured in kilograms and the speed is measured in meters per second, the kinetic energy is measured in kilogram-meters squared per second squared.

For more information on kinetic and potential energy kindly visit to

https://brainly.com/question/11749818

#SPJ1

Two children are playing a game in which they try to hit a small box on the floor with a marvel fired from a spring-loaded gun that is mounted on a table. The target box is at a horizontal distance D = 2.2m from the edge of the table. Bobby compresses the spring 1.7cm, but the center of the marble falls 27cm short of the center of the box. How far should Rhoda compress the spring to score a direct hit? Assume that neither the spring nor the ball encounters friction in the gun.

Answers

The distance till which Rhoda should compress the spring to score a direct hit is 1.37 centimeters.

How far should Rhoda compress the spring?

Rhoda needs to compress the spring by a distance of 1.37cm to score a direct hit. The equation to find this distance is: D = [tex][(x + y)^2 - x^2]^{(1/2)}[/tex]

where, D is the horizontal distance, x is the initial compression of the spring (1.7cm), and y is the additional compression needed to reach the target box (the unknown).

To solve for y, we can rearrange the equation as:

[tex]y = [(D^2 - x^2]^{(1/2)} - x\\[/tex]

Plugging in the values, we have

[tex]y = [(2.2^2 - (1.7)^2]^{(1/2)}[/tex]- 1.7 = 1.37cm

Therefore, Rhoda needs to compress the spring by 1.37 cm to score a direct hit.

Learn more about Spring here:

https://brainly.com/question/14670501

#SPJ11

The position of a toy locomotive moving on a straight track along the x axis is given by the equation x = t^3 - 6t^2 + 9t, where x is in meters and t is in seconds. The net force on the locomotive is equal to zero when t is equal to (A) zero (B) 2 s (C) 3 s (D) 4 s (E) 5 s

Answers

Option C, The net force on the toy locomotive moving on a straight track along the x-axis is equal to zero at t=3s.

A force is any push or pull that results in a modification in the state of motion of an object. The net force on an object is the combination of all forces acting on it in a specific direction. An object in motion will continue to move in a straight line at a steady velocity unless acted upon by a net force, according to Newton's first law of motion. The equation of motion for the toy locomotive is as follows:

x = t³ - 6t² + 9t

We must differentiate this equation twice to determine the acceleration of the toy locomotive.

a = x′′= 6t - 12, At time t = 3 seconds, the net force on the toy locomotive is zero. This occurs when the acceleration of the toy locomotive equals zero.

6t - 12 = 0t = 2

Therefore, the net force on the toy locomotive moving on a straight track along the x-axis is equal to zero at t = 3 seconds.

Learn more about force and locomotive at : https://brainly.com/question/14206785

#SPJ11

In a photoelectric experiment using a sodium surface, you find a stopping potential of 1.85V for a wavelength of 300nm and a stopping potential of 0.820V for a wavelength of 400nm. From these data find (a) a value for the Planck constant, (b) the work function Φ for sodium, and (c) the cutoff wavelength λ0​ for sodium.

Answers

The Planck constant is 1.41 x 10-34 Js, the work function Φ for sodium is 2.39 eV, and the cutoff wavelength λ₀​ for sodium is 590 nm.

Using the data, we can calculate the Planck constant, work function, and cutoff wavelength for sodium.

To start, we use the formula E = hc/λ, where E is the stopping potential, h is the Planck constant, c is the speed of light, and λ is the wavelength.

To find the Planck constant, we rearrange the equation to get h = Eλ/c.

Plugging in the values from the data, we get

h = (1.85 V)(300 nm)/(3 x 108 m/s)

= 1.41 x 10-34 Js.

Now to find the work function Φ for sodium, we use the equation Φ = hc/λ - E.

Plugging in the values from the data, we get

Φ = (1.41 x 10-34 Js)(3 x 108 m/s)/(400 nm) - 0.82 V = 2.39 eV.

Finally, to find the cutoff wavelength λ₀ for sodium, we use the equation λ₀​ = hc/Φ.

Plugging in the values from the data, we get

λ₀​ = (1.41 x 10-34 Js)(3 x 108 m/s)/2.39 eV = 590 nm.

Therefore, the Planck constant is 1.41 x 10-34 Js, the work function Φ for sodium is 2.39 eV, and the cutoff wavelength λ₀ for sodium is 590 nm.

Learn more about "Planck constant, work function, wavelength" at : https://brainly.com/question/2289138

#SPJ11

what is large solar eruptions that occur near sunspots

Answers

Large solar eruptions near sunspots are known as coronal mass ejections (CMEs).

what are CMEs?

Coronal mass ejections (CMEs) are huge explosions of plasma and magnetic fields from the sun's corona, the outermost layer of the sun's atmosphere. Sunspots are areas on the sun's surface where the magnetic field is much stronger than surrounding regions, which can lead to the buildup of energy that can trigger a CME.

CMEs can release vast amounts of energy and can cause solar flares, geomagnetic storms, and other space weather phenomena that can affect our planet.

They can also pose a danger to astronauts and satellites in space. Scientists study CMEs to better understand the sun's behavior and how it affects Earth and the rest of the solar system.

Learn about CMEs here https://brainly.com/question/23787803

#SPJ1

The width of the cube was 18. 45 mm. The density of the cube was 8. 0 × 103 kg/m3

Calculate the mass of the cube

Answers

The required mass of the cube when width of the cube and density of the cube are specified is calculated to be 0.0502 kg.

The width of the cube is given as 18.45 mm = 18.45 × 10⁻³ m

The density of the cube is given as 8 × 10³ kg/m³.

Mass of the cube is to be found out.

The general formula for density of a cube is given by, V = s³

where,

V is volume

s is side/width/height (As they are all equal in a cube)

So, the volume of the cube is,

V = (18.45 × 10⁻³)³ = 0.01845³ = 6.28 × 10⁻⁶ m³

Now, we know the general equation for density as, mass upon unit volume.

Mathematically, D = m/V

Making m as subject, we have,

Mass m = D × V = 8 × 10³ × 6.28 × 10⁻⁶ = 50.24× 10⁻³ kg = 0.0502 kg

Thus, the required mass is calculated to be 0.0502 kg.

To know more about density:

https://brainly.com/question/952755

#SPJ4

true or false if the whole picture plane is affected by aerial diffusion, it stops being an effective indicator of depth.

Answers

If the whole picture plane is affected by aerial diffusion, it stops being an effective indicator of depth - this statement is true.

Aerial diffusion is the scattering of light by particles in the air. These particles cause distant objects to appear fainter and bluer than closer objects, leading to a decrease in visual clarity and the ability to perceive depth. Aerial diffusion can be utilized in painting and drawing to create an atmospheric perspective, which produces a sense of depth by making objects are that further away appear hazier and less distinct than those that are closer. However, if the entire picture plane is affected by aerial diffusion, this can make it difficult to distinguish between objects at different depths, which can result in a lack of clarity and depth perception in the painting or drawing.

A picture plane is a theoretical plane that corresponds to the surface of a painting or drawing. The picture plane is where the artist organizes and arranges the various elements of the composition to create a visual representation of a scene. The picture plane is where the viewer's eye interacts with the artwork, and where the illusion of depth and space is created. In this context, the picture plane is an important factor in the creation of depth and atmosphere in a painting or drawing.

Learn more about aerial diffusion:

https://brainly.com/question/1381101

#SPJ11

(Astronomy)
The term "Milky Way" comes from its Latin name Via Lactea. What does this mean?

global clusters

glowing band

two major arms

the road of milk

ANSWER: D (The road of milk.)

Answers

The Roman word Via Lactea, which translates to "the road of milk," is where the phrase "Milky Way" originates.

What is Milky way?

The Milky Way is a barred spiral galaxy, a galaxy with a central bar-shaped structure made up of stars. It is estimated to be about 100,000 light-years in diameter and contains billions of stars, as well as dust, gas, and dark matter. The Sun is located within the Milky Way, about 25,000 light-years away from the galactic center. The Milky Way is visible to the eye as a faint, glowing band of stars across the night sky, and it appears as a bright, hazy band in images taken by telescopes. It is named after the milky-white appearance of the band of stars, which is caused by the combined light of millions of individual stars.

This name was given to the galaxy by the ancient Greeks, who believed that the Milky Way was formed by milk spilling from the breasts of the goddess Hera. The name "Milky Way" refers to the hazy band of light that stretches across the night sky, which is caused by the light of billions of stars in our galaxy. The Milky Way is a barred spiral galaxy, with a central bar-shaped structure surrounded by two major arms and several minor arms. It contains over 100 billion stars and is estimated to be about 13.6 billion years old.

Learn more about Milky way from given link

https://brainly.com/question/13956361

#SPJ1

Star A is identical to Star B, but Star A is twice as far from us as Star B. Therefore, _______________.

Answers

Star A's light will take longer to reach us.

as noted in this chapter, plants help to reduce water runoff and soil erosion, both of which affect the health of streams and rivers by impacting water quality. soil erosion increases the silt load in water and this literally smothers living organisms, particularly plants and invertebrate species. runoff water can carry pollutants, particularly pesticides and herbicides from agricultural land. read the description of each landscape and rank them from best stream quality to worst stream quality. 1: streams cutting through small farms with several different crop types and natural vegetation buffers between the fields and the streams. 2: a large floodplain area covered with lowland forests and swamps full of emergent vegetation, with small streams cutting through the area. 3: an urban housing development where the trees growing along the streams were removed and replaced with lawns. 4: a system of large farms with no buffer vegetation between the fields and the streams that cut through the farms. question list (4 items) (drag and drop into the appropriate area) landscape 1 landscape 2 landscape 3 landscape 4 correct answer list best stream quality

Answers


Plants help to reduce water runoff and soil erosion, both of which affect the health of streams and rivers by impacting water quality.

Soil erosion increases the silt load in the water, which can smother living organisms, particularly plants and invertebrate species. Runoff water can carry pollutants, particularly pesticides, and herbicides from agricultural land.

Landscape 1 (streams cutting through small farms with a variety of crop types and natural vegetation buffers between the fields and the streams) would be the best quality, followed by Landscape 2 (a large floodplain area covered in lowland forests and swamps full of emergent vegetation, with small streams cutting through the area) and Landscape 3 (an urban housing development where the streams are surrounded by emergent vegetation).

Learn more about water quality at  brainly.com/question/20848502

#SPJ11

an incompressible substance with a density of 1000 kg/m3 is isothermally compressed from 100 to 1000 kpa. determine the change in enthalpy. multiple choice question. 0 kj/kg 0.9 kj/kg 10 kj/kg 900 kj/kg

Answers

The change in enthalpy of an incompressible substance with a density of 1000 kg/m³ that is isothermally compressed from 100 to 1000 kPa is 0 kJ/kg.

What is enthalpy?

Enthalpy is a measure of the total energy of a thermodynamic system. In addition, it incorporates the energy that is supplied to the system as heat, as well as any energy that is used as work. Enthalpy is represented by the symbol H and is usually calculated in units of joules (J).

What is an incompressible substance?

An incompressible substance is one that cannot be compressed or compressed to a significant degree. Liquids are examples of such materials. They are often described as having a constant density because, unlike gases, they do not easily change in volume in response to pressure or temperature changes. Therefore, the change in enthalpy is 0 kJ/kg.

Learn more about Enthalpy here: https://brainly.com/question/16985375.

#SPJ11

A 1500 kg car is moving to the right with a speed of 20.0 m/s when it collides with a wall and reboubds at a speed of 5.00 m/s.

If the collision lasts for 250 ms, then the magnitude of the average force acring on the car is _____ kN (the answer is 150 but I'm not sure how)
pls help!! ​

Answers

Answer:

See below.

Explanation:

When the 1500 kg car collides with the wall and rebounds at a speed of 5.00 m/s, we can calculate the change in the car's velocity using the following formula:

Δv = v2 - v1

Where Δv is the change in velocity, v2 is the final velocity, and v1 is the initial velocity. Substituting the given values, we get:

Δv = 5.00 m/s - 20.0 m/s

Δv = -15.0 m/s

The negative sign indicates that the direction of the car's velocity has reversed, or that the car is now moving to the left. To calculate the magnitude of the change in velocity, we take the absolute value:

|Δv| = |-15.0 m/s|

|Δv| = 15.0 m/s

Therefore, the magnitude of the change in velocity is 15.0 m/s.

Now,

To find the magnitude of the average force acting on the car during the collision, we can use the impulse-momentum theorem, which states that:

Impulse = change in momentum

Average force = Impulse / time

The change in momentum of the car is given by:

Δp = mΔv

where Δv is the change in velocity calculated in the previous answer and m is the mass of the car.

Δp = 1500 kg × (-15.0 m/s)

Δp = -22500 kg·m/s

The impulse acting on the car during the collision is equal to the change in momentum:

Impulse = Δp = -22500 kg·m/s

To find the magnitude of the average force acting on the car during the 250 ms collision, we divide the impulse by the duration of the collision:

Average force = Impulse / time

Average force = -22500 kg·m/s / 0.250 s

Average force ≈ -90,000 N

The negative sign indicates that the force is in the opposite direction of the car's motion, or to the left. Therefore, the magnitude of the average force acting on the car during the collision is approximately 90,000 N.

By what factor would you have to increase a at constant n to have the zero point energies of a Ne atom be equal to the zero point energy of a hydrogen atom in the box?

Answers

The zero point energies of a Ne atom be equal to the zero point energy of a hydrogen atom in the box, you would have to increase a at constant n by a factor of 4π²/3.


The zero-point energy is the smallest amount of energy that a quantum mechanical physical system can have. It is the energy that a system has when it is at its lowest possible energy state.

In order to have the zero point energies of a Ne atom equal to the zero point energy of a hydrogen atom in the box, this is because the zero point energy of a Ne atom is equal to 4π² times the zero point energy of a hydrogen atom, which is given by the equation E0 = h²/(8ma2).

Therefore, the factor by which a has to be increased at constant n to have the zero point energies of a Ne atom be equal to the zero point energy of a hydrogen atom in the box is by a factor of 4π²/3.

Learn more about zero point energies here:

https://brainly.com/question/30402910

#SPJ11

a ceiling fan is turned on and a net torque of 2.3 n*m applied to the blades. the blades have a total moment of inertia of 0.39 kg*m^2. what is the angular acceleration of the blades?

Answers

The angular acceleration of the blades  is 5.897 rad/s². It can be calculated using the formula α as the ratio of torque to moment of Inertia.

The torque is a rotational or twisting force. Angular acceleration is the rate at which the angular velocity of an object changes, measured in radians per second squared (rad/s²).

Given the torque and moment of inertia, we may utilize the following formula to find the angular acceleration of the blades:

[tex]\alpha= \dfrac{Torque}{Moment \; of \; inertia}\\\alpha= \dfrac{\tau}{I}[/tex]

where τ is the torque in newton-meters (N-m),I is the moment of inertia in kg-m², α is the angular acceleration in radians per second squared (rad/s²).

Rearranging the formula to solve for α gives:

[tex]\alpha=2.3/0.39\\=5.897 rad/s^2[/tex]

Therefore, the angular acceleration of the blades is 5.897 rad/s².

For further information about angular acceleration click on below link:

https://brainly.com/question/30238727

#SPJ11

Consider the spectra of the two main sequence stars below (Star 1 on the left and Star 2 on the right) and sort the statements into the true or false bins. The intensity axes are not necessarily on the same scale. 350 450 550 Wavelength (nm) 350 45Q750 650 750 Wavelength (nm) true false Star 1 has a longer lifetime than Star 2 Star 2 is bluer than Star 1 Star 2 has a lower mass than Star 1 Star 1 has prominent hydrogen lines Star 2 has a higher luminosity than Star 1 Star 2 is cooler than Star 1.

Answers

. Additionally, Star 1 has prominent hydrogen lines, indicating a lower temperature than Star 2. Therefore, the statements can be sorted into the true and false bins as indicated above.

True: Star 1 has a longer lifetime than Star 2; Star 2 is bluer than Star 1; Star 2 has a lower mass than Star 1; Star 1 has prominent hydrogen lines.

False: Star 2 has a higher luminosity than Star 1; Star 2 is cooler than Star 1.

The spectra of the two main sequence stars illustrate some differences between the two stars. Star 1 is on the left and has a longer lifetime than Star 2, which is on the right. This is evident from the intensity axes that are not on the same scale. Star 2 has a lower mass than Star 1, is bluer than Star 1, and has a lower luminosity

for such more questions on hydrogen lines

https://brainly.com/question/30461609

#SPJ11

A wave interaction that occurs when two waves are in the same place at the same time

Answers

The wave interaction that occurs when two waves are in the same place at the same time is called interference.

Interference can be either constructive or destructive, depending on the relative phases of the waves.

What is constructive interference?

Constructive interference occurs when two waves have the same phase and their amplitudes add together. The resulting wave has a larger amplitude than either of the individual waves. This can be seen, for example, when two speakers playing the same sound are placed close together.

What is destructive interference?

Destructive interference occurs when two waves have opposite phases and their amplitudes subtract from each other. The resulting wave has a smaller amplitude than either of the individual waves. This can be seen, for example, when two waves with equal amplitude and wavelength are superimposed, but one is shifted by half a wavelength relative to the other.

To know more about interference, visit:

https://brainly.com/question/16098226

#SPJ1

Complete question is: The wave interaction that occurs when two waves are in the same place at the same time is called interference.

A convex lens is shown here with an arrow in the left indicating the light moving through the lens. Assuming that
the lens is made of material that has a higher density than the air, predict the direction of the light after it passes
through the lens.

A The light will bend downward significantly as is indicated by arrow D.

B The light will bend upward as is indicated by arrow A.

C The light will continue on its straight path, as indicated by arrow B.

D The light will bend downward slightly as is indicated by arrow C.



Picture

Answers

Answer:

B The light will bend upward as is indicated by arrow A.

Explanation:

I just did the progress learning test

a rectangular field is twice as long as it is wide. the perimeter of the field is 450 yards. find the dimensions of the field. you must find an equation to represent the situation and solve.

Answers

The dimensions of the field can be found to be 75 yards in width and 150 yards in length.

Given:
Let the width of the rectangular field be x
Length of the rectangular field = 2x
Perimeter of the rectangular field = 450 yards


Formula Used:
Perimeter of a rectangle = 2 (l + w)

Where l and w are the length and width of the rectangle respectively.

Solution:
As per the question,
Perimeter of the rectangular field = 450 yards


Therefore, 2(Length + Width) = 450
2(x + 2x) = 450
2(3x) = 450
6x = 450
x = 75
Therefore, the width of the rectangular field is 75 yards
Length of the rectangular field = 2x = 2 × 75 = 150 yards

Hence, the dimensions of the field are 75 yards by 150 yards.

To know more perimeter, refer here:

https://brainly.com/question/30252651#

#SPJ11

What do the areas labeled x, y, and z represent? constructive interference in which waves cancel each other out constructive interference in which waves strengthen each other destructive interference in which waves cancel each other out destructive interference in which waves strengthen each other

Answers

The correct option is B, the areas labeled X, Y, and Z represent constructive interference in which waves strengthen each other.

Interference is a phenomenon that occurs when two or more waves interact with each other. In physics, waves can be described as a disturbance that travels through a medium, such as water or air. When two waves meet, they can either reinforce or cancel each other out, depending on their amplitudes and phases.

Constructive interference occurs when the peaks of two waves coincide, creating a larger amplitude than either wave alone. Destructive interference occurs when the peak of one wave coincides with the trough of another, resulting in a cancellation of the waves. Interference is a fundamental concept in many areas of physics, including optics, acoustics, and electromagnetism.

To learn more about Interference visit here:

brainly.com/question/16098226

#SPJ4

Complete Question:

The diagram shows monochromatic light passing through two openings.

What do the areas labeled X, Y, and Z represent?

A). constructive interference in which waves cancel each other out

B). constructive interference in which waves strengthen each other

C). destructive interference in which waves cancel each other out

D). destructive interference in which waves strengthen each other

a 1540-kg parked truck has a wheel base of 3.13 m (this is the distance between the front and rear axles). the center of mass of the truck is 1.3 m behind the front axle. (a) what is the force exerted by the ground on each of the front wheels? [4000,5000] n (b) what is the force exerted by the ground on each of the back wheels? [3000,4000] n hint: this is a chapter 12 equilibrium problem. remember that the truck has four wheels, not just the two you can see in the drawing.

Answers

The force exerted by the ground on each of the front wheels is 4532 N. and the force exerted by the ground on each of the back wheels is 6108 N.

a) Calculation of the force exerted by the ground on each of the front wheels of a 1540-kg parked truck

The force exerted by the ground on each of the front wheels can be calculated as follows:

First, calculate the weight of the truck using the

formula: w=mg

Where w is the weight of the truck,

m is the mass of the truck, and

g is the acceleration due to gravity.

Substituting the given values in the formula, we have:

w=mg=1540×9.8=15172 N

Next, calculate the moment of the weight of the truck about the rear axle using the formula: mr =w×(l−d)

Where mr is the moment of the weight of the truck about the rear axle,

w is the weight of the truck,

l is the wheelbase, and

d is the distance between the center of mass and the front axle.

Substituting the given values in the formula, we have:

mr=15172×(3.13−1.3)=24967.84 Nm

Since the truck is in equilibrium, the force exerted by the ground on each of the front wheels must be equal to the weight of the truck minus half of the moment of the weight of the truck about the rear axle, divided by the distance between the front and rear axles.

Therefore, we have F=½(w×l−mr)/

where F is the force exerted by the ground on each of the front wheels. Substituting the given values in the formula, we have F=½(15172×3.13−24967.84)/3.13=4532 N

b) Calculation of the force exerted by the ground on each of the back wheels of a 1540-kg parked truck.

The force exerted by the ground on each of the back wheels can be calculated as follows:

Since the truck is in equilibrium, the force exerted by the ground on each of the back wheels must be equal to the weight of the truck minus the force exerted by the ground on each of the front wheels.

Therefore, we have: F= w−2Ff

Where F is the force exerted by the ground on each of the back wheels, and Ff is the force exerted by the ground on each of the front wheels.

Substituting the given values in the formula, we have: F=15172−2×4532=6108 N

To know more about Force: https://brainly.com/question/12785175

#SPJ11

The theory of plate tectonics was created by this evidence.

Sea floor spreading

Ridges in the sea floor moving outward.

Due to the sea floor spreading the continental crust must be moving as well

Answers

The process through which tectonic plates—large slabs of Earth's lithosphere—split away from each other is known as seafloor spreading.

What is seafloor spreading?

Mantle convection causes seafloor spreading and other tectonic activity processes. Divergent plates, a form of tectonic activity that results in plates moving away from each other, causing seafloor spreading. Diverge Seafloor spreading results in three major characteristics of the seafloor: the age of the seafloor becomes progressively older as one moves away from mid-ocean ridges,  the elevation of the seafloor becomes progressively lower as one moves away from mid-ocean ridges, and the magnetic history of the seafloor bears the striped-pattern of the Earth's magnetic.

Learn more about seafloor

https://brainly.com/question/17914057

#SPJ1

A Nichrome wire 75 cm long and 0.25 mm in diameter is connected to a 1.7 volt flashlight battery.
A) What is the electric field inside the wire?
B) Next the Nichrome wire is replaced by a wire of the same length and diameter, and same mobile electron density but with electron mobility 4 times as large as that of Nichrome. Now what is the electric field inside the wire?

Answers

The electric field inside the wire is still about 2.27 V/m, even though the electron mobility is 4 times higher. This is because the resistance of the wire remains the same, and Ohm's law still applies. The higher conductivity only means that a higher current flows through the wire for the same voltage, but the electric field remains the same.

We can use Ohm's law to find the electric field inside the Nichrome wire:

V = IR

where

V = 1.7 volts (battery voltage)

I = current

R = resistance of the wire

The resistance of a wire can be calculated using the formula:

R = (ρL) / A

where

ρ = resistivity of the material

L = length of the wire

A = cross-sectional area of the wire

The resistivity of Nichrome is about 1.10 x 10^-6 Ωm, and the cross-sectional area of the wire can be calculated using the formula for the area of a circle:

A = πr^2

where

r = radius of the wire = 0.125 mm = 0.000125 m

So, A = π(0.000125 m)^2 = 4.91 x 10^-8 m^2

Substituting the values, we get:

R = (1.10 x 10^-6 Ωm)(0.75 m) / (4.91 x 10^-8 m^2)

R ≈ 0.017 Ω

Now we can find the current:

I = V / R

I = 1.7 volts / 0.017 Ω

I ≈ 100 amps

The electric field inside the wire can be calculated using the formula:

E = V / L

where

E = electric field

V = potential difference

L = length of the wire

Substituting the values, we get:

E = 1.7 volts / 0.75 m

E ≈ 2.27 volts/meter or 2.27 V/m

So the electric field inside the Nichrome wire is about 2.27 V/m.

Next, we can repeat the calculations for the wire with the higher electron mobility. Since the mobile electron density and the length and diameter of the wire are the same, the resistance of the wire will also be the same as before. However, the higher electron mobility means that the wire will have a higher conductivity, which in turn means that the current will be higher for the same voltage.

Let's assume that the electron mobility is 4 times higher than that of Nichrome. Since the resistivity of the material remains the same, the conductivity will be 4 times higher as well. Therefore, the current will be 4 times higher than before:

I = 4 x 100 amps = 400 amps

Using the same formula as before, the electric field inside the wire can be calculated:

E = V / L

E = 1.7 volts / 0.75 m

E ≈ 2.27 volts/meter or 2.27 V/m

So, the electric field inside the wire is still about 2.27 V/m, even though the electron mobility is 4 times higher. This is because the resistance of the wire remains the same, and Ohm's law still applies. The higher conductivity only means that a higher current flows through the wire for the same voltage, but the electric field remains the same.

For such more questions on Ohm's law

https://brainly.com/question/14634041

#SPJ11

A gas is compressed at a constant pressure from a volume of 10 m3 to a volume of 4 m3 , then work done on the system is:
a) nRT ln 1/6
b) nRT In2/5
c) nRT In 5/2
d) nRT In 6

Answers

None of the answer options provided are correct as they all involve calculations that assume certain values for the pressure, volume, and temperature of the gas.

What is Constant Pressure?

Constant pressure is a thermodynamic process in which the pressure of a system remains constant during the process. This means that any change in volume or temperature of the system must be accompanied by a corresponding change in some other property, such as the amount of heat added or removed from the system.

Since the gas is compressed at a constant pressure, the work done on the system can be calculated as:

W = -PΔV

In this case, P is constant, so we have:

W = -P(V2 - V1)

W = -P(4 m^3 - 10 m^3)

W = -P(-6 m^3)

W = 6P m^3

Since we are not given any information about the type of gas or its properties, we cannot use the ideal gas law to calculate the pressure P. Therefore, we cannot determine the exact value of the work done on the system.

Learn more about Constant Pressure from given link

https://brainly.com/question/2139620

#SPJ1

For this truss geometry:
|/\|/\|/\|/\|
Select one or more:
a. The bottom chords do not usually need the verticals, since the bottom chords are not subjected to bending loads and the bottom chords only go into compression under severe wind suction that overcomes the dead weight of the structure.
b. This is called a Modified Warren Truss.
c. The vertical webs help brace the top chord against buckling upward and downward.
d. The vertical webs help support parts of the top chord, thereby reducing the span, and associated bending stress, of the top chord under the uniform gravity force of the decking resting on the top chord of the truss.
e. The unbraced length for the bottom chords is twice as long as the unbraced length for the top chords.

Answers

The correct statements are as follows: Option (b), (c) and (d). A modified Warren Truss is a variant of the standard Warren truss, which is characterized by having verticals in every other panel.

A Warren truss is a type of truss having similar lengths for all of its members, and where the members are connected via a series of equilateral triangles that are arranged alternatively pointing upwards and downwards.

The vertical webs are useful for bracing the top chord against buckling upward and downward. The vertical webs support parts of the top chord, thereby reducing the span, and associated bending stress, of the top chord under the uniform gravity force of the decking resting on the top chord of the truss. Therefore the correct answers are options (a), (b), and (d).

Learn more about The vertical supports in bridge: brainly.com/question/21727232

#SPJ11

Other Questions
explain three ways that show how your personal online profile or post could negatively influence a prospective employers view of you during the recruitment process At periodic time intervals, ____ technology downloads updated, personalized information on your screen. 93. Electricity Usage The graph showsthe daily megawatts of electricity usedon a record-breaking summer day inSacramento, California.(a) Is this the graph of a function?(b) What is the domain?(c) Estimate the number of megawattsused at 8 A.M.(d) At what time was the most electric-ity used? the least electricity?(e) Call this function f. What is f(12)?Interpret this answer.(f) During what time intervals is usageincreasing? decreasing? _'s diamond model Theory of National Competitiveness sought to explain the factors that lead a country to have a competitive advantage over other countries in a certain product or products? a.Adam Smith b.David Ricardo c.Michael Porte. A girl walks from her home to a friends home 3 blocks north. She then walks 2 blocks east to the post office. 1 block north to the library, and one block east to the park. From the park, she walks 2 blocks west to the movie theater. After the movie, she walks 4 blocks south to the pet store. What is the girls displacement from her starting point to the pet store? Where is the location of the pet store in relation to her home? Calculate the distance she walked in blocks. What does it mean if you and your partner have the same moon sign? In what ways does the struggle for freedom change with history? What have you learned about the nature of any struggle for freedom by reading these poems, one of which was written almost 150 years ago? an american politician and attorney who is the 49th and current vice president of the us. she is the first female and first african american vp, who is she? how many legs does it take to make 109657 spiders Describe the evolution of the Auschwitz concentration camps in 3-5 sentences if a media company wants information on consumers' television viewing habits, it can purchase reports compiled by commercial research firms such as nielsen. this is an example of Commercial agriculture in dry climates relies heavily on irrigation. Which of the following best explains an environmental concern that results from irrigation in arid regions?The high use of water for agriculture increases the price of water for people in urban areas.The soil will have increased salinity, leading to soil erosion and reduced nutrients in the soil for plant health.The increased production that results from irrigation of the crop will lead to decreases in crop prices as the total crop harvested will be higher.The plants grown in this dry region will start to adapt to use less water, but the period to maturity will increase. Why does Twain call the apprentice an undeserving reptile Find the inverse of the function Which of the following sequence is used by the attacker, in the Directory Traversal Attacks to access restricted directories outside of the web server root directory. Select one/...//.....//../ When electrons flow along the electron transport chains of mitochondria, which of the changes occurs? The correct answer is (B) the pH of the matrix increases. As electrons are passed along the electron transport chains, protons are actively transported from the mitochondrial matrix into the intermembrane space. true or false there is a risk that a company will differentiate its products or services in ways that the customer does not value. we are too late . The train. _________ (leaving) Determine the total amount of money that was utilized on fuel in June 2022 The organizer of a late night street fair in a popular tourist city wants to analyze the relationship between daily revenue and the following variables: the number of male visitors, the number of female visitors, the number of retail stands, the number of food (and beverage) stands, and the number of performances that take place on a given night. The regression output table is provided below. Based on these results and using a 10% significance level, the organizer thinks he can improve the model. He wants to try removing at least one variable from the analysis to create and compare new models. Which variable or variables would you recommend that he consider removing from the regression model? SELECT ALL THAT APPLY.