Answer:
200cm
Explanation:
Answer:
100cm
Explanation:
Using
F= ( N/2L)(√T/u)
F1 will now be (0.5*2)( √600/0.015)
=> L( wavelength)= 200/2cm = 100cm
A string of holiday lights has 15 bulbs with equal resistances. If one of the bulbs
is removed, the other bulbs still glow. But when the entire string of bulbs is
connected to a 120-V outlet, the current through the bulbs is 5.0 A. What is the
resistance of each bulb?
Answer:
Resistance of each bulb = 360 ohms
Explanation:
Let each bulb have a resistance r .
Since, even after removing one of the bulbs, the circuit is closed and the other bulbs glow. Therfore, the bulbs are connected in Parallel connection.
[tex] \frac{1}{r(equivalent)} = \frac{1}{r1} + \frac{1}{r2} + + + + \frac{1}{r15} [/tex]
[tex] \frac{1}{r(equivalent)} = \frac{15}{r} [/tex]
R(equivalent) = r/15
Now, As per Ohms Law :
V = I * R(equivalent)
120 V = 5 A * r/15
r = 360 ohms
hat a 15 kg body is pulled along a horizontal fictional table by a force of 4N what is the acceleration of the body
Answer:
Acceleration of the body is:
[tex]a=0.27\,\,m/s^2[/tex]
Explanation:
Use Newton's second Law to solve for the acceleration:
[tex]F=m\,\,a\\a=\frac{F}{m} \\a=\frac{4\,N}{15\,\,kg} \\a=0.27\,\,m/s^2[/tex]
When a mercury thermometer is heated, the mercury expands and rises in the thin tube of glass. What does this indicate about the relative rates of expansion for mercury and glass
Answer:
This means that mercury has a higher or faster expansion rate than glass
Explanation:
This is because When a container expands, the reservoir in the glass expands at the same rate as the glass. Thus, if there is something in a glass and both expand at the same rate, they have no change - but if the contents expand faster, they will fill the container to a higher level, and if the contents expand slower, they will fill the container to a lower level (relative to the new size of the container).
Adjust the mass of the refrigerator by stacking different objects on top of it. If the mass of the refrigerator is increased (with the Applied Force held constant), what happens to the acceleration
Answer:
The acceleration of the refrigerator together with the objects decreases.
Explanation:
If the mass of the refrigerator is increased by stacking more masses (objects) on it,
and the force applied remains constant, then we know from
F = ma
where
F is the applied force
m is the total mass of the refrigerator and the objects
a is the acceleration of the masses.
If F is constant, and m is increased, the acceleration will decrease
Answer:
The acceleration decreases.
Explanation:
its right
You're conducting an experiment on another planet. You drop a rock from a height of 1 m and it hits the ground 0.4 seconds later. What is acceleration due to gravity on the planet ?
Answer:
Here,
v (final velocity) = 0
u (initial velocity) = u
a = ?
s = 1m
t = 0.4s
using the first equation of motion,
0 = u + 0.4a
= -0.4a = u
using the second equation of motion:
1 = 0.4u + 0.08a
from the bold equation
1 = 0.4(-0.4a) + 0.08a
1 = -0.16a + 0.08a
1 = -0.08a
a = -1/0.08
a = -100/8
a = -12.5 m/s/s
please make me brainly, i am 1 brainly away from the next rank
The sun generates both mechanical and electromagnetic waves. Which statement about those waves is true?
OA. The mechanical waves reach Earth, while the electromagnetic waves do not.
OB. The electromagnetic waves reach Earth, while the mechanical waves do not.
OC. Both the mechanical waves and the electromagnetic waves reach Earth.
OD. Neither the mechanical waves nor the electromagnetic waves reach Earth.
Answer: The correct answer for this question is letter (B) The electromagnetic waves reach Earth, while the mechanical waves do not. The sun generates both mechanical and electromagnetic waves. Space, between the sun and the earth is a nearly vacuum. So mechanical wave can not spread out in the vacuum.
Hope this helps!
Answer:
The electromagnetic waves reach Earth, while the mechanical waves do not
Exercise 2.4.5: Suppose we add possible friction to Exercise 2.4.4. Further, suppose you do not know the spring constant, but you have two reference weights 1 kg and 2 kg to calibrate your setup. You put each in motion on your spring and measure the frequency. For the 1 kg weight you measured 1.1 Hz, for the 2 kg weight you measured 0.8 Hz. a) Find k (spring constant) and c (damping constant). Find a formula for the mass in terms of the frequency in Hz. Note that there may be more than one possible mass for a given frequency. b) For an unknown object you measured 0.2 Hz, what is the mass of the object? Suppose that you know that the mass of the unknown object is more than a kilogram.
Answer:
a) k = 95.54 N / m, c = 19.55 , b) m₃ = 0.9078 kg
Explanation:
In a simple harmonic movement with friction, we can assume that this is provided by the speed
fr = -c v
when solving the system the angular value remains
w² = w₀² + (c / 2m)²
They give two conditions
1) m₁ = 1 kg
f₁ = 1.1 Hz
the angular velocity is related to frequency
w = 2π f₁
Let's find the angular velocity without friction is
w₂ = k / m₁
we substitute
(2π f₁)² = k / m₁ + (c / 2m₁)²
2) m₂ = 2 kg
f₂ = 0.8 Hz
(2π f₂)² = k / m₂ + (c / 2m₂)²
we have a system of two equations with two unknowns, so we can solve it
we solve (c / 2m)² is we equalize the expression
(2π f₁)² - k / m₁ = (2π f₂²) 2 - k / m₁
k (1 / m₂ - 1 / m₁) = 4π² (f₂² - f₁²)
k = 4π² (f₂² -f₁²) / (1 / m₂ - 1 / m₁)
a) Let's calculate
k = 4 π² (0.8² -1.1²) / (½ -1/1)
k = 39.4784 (1.21) / (-0.5)
k = 95.54 N / m
now we can find the constant of friction
(2π f₁) 2 = k / m₁ + (c / 2m₁)²
c2 = ((2π f₁)² - k / m₁) 4m₁²
c2 = (4ππ² f₁² - k / m₁) 4 m₁²
let's calculate
c² = (4π² 1,1² - 95,54 / 1) 4 1²
c² = (47.768885 - 95.54) 8
c² = -382.1689
c = 19.55
b) f₃ = 0.2 Hz
m₃ =?
(2πf₃)² = k / m₃ + (c / 2m₃) 2
we substitute the values
(4π² 0.2²) = 95.54 / m₃ + 382.1689 2/4 m₃²
1.579 = 95.54 / m₃ + 95.542225 / m₃²
let's call
x = 1 / m₃
x² = 1 / m₃²
- 1.579 + 95.54 x + 95.542225 x² = 0
60.5080 x² + 60.5080 x -1 = 0
x² + x - 1.65 10⁻² = 0
x = [1 ±√ (1- 4 (-1.65 10⁻²)] / 2
x = [1 ± 1.03] / 2
x₁ = 1.015 kg
x₂ = -0.015 kg
Since the mass must be positive we eliminate the second results
x₁ = 1 / m₃
m₃ = 1 / x₁
m₃ = 1 / 1.1015
If the
refractive index of benzere is 2.419,
what is the speed of light in benzene?
Answer:
[tex]v=1.24\times 10^8\ m/s[/tex]
Explanation:
Given that,
The refractive index of benzene is 2.419
We need to find the speed of light in benzene. The ratio of speed of light in vacuum to the speed of light in the medium equals the refractive index. So,
[tex]n=\dfrac{c}{v}\\\\v=\dfrac{c}{n}\\\\v=\dfrac{3\times 10^8}{2.419}\\\\v=1.24\times 10^8\ m/s[/tex]
So, the speed of light in bezene is [tex]1.24\times 10^8\ m/s[/tex].
If Superman really had x-ray vision at 0.12 nm wavelength and a 4.1 mm pupil diameter, at what maximum altitude could he distinguish villains from heroes, assuming that he needs to resolve points separated by 5.4 cm to do this?
Answer:
Maximum altitude to see(L) = 1.47 × 10⁶ m (Approx)
Explanation:
Given:
wavelength (λ) = 0.12 nm = 0.12 × 10⁻⁹ m
Pupil Diameter (d) = 4.1 mm = 4 × 10⁻³ m
Separation distance (D) = 5.4 cm = 0.054 m
Find:
Maximum altitude to see(L)
Computation:
Resolving power = 1.22(λ / d)
D / L = 1.22(λ / d)
0.054 / L = 1.22 [(0.12 × 10⁻⁹) / (4 × 10⁻³ m)]
0.054 / L = 1.22 [0.03 × 10⁻⁶]
L = 0.054 / 1.22 [0.03 × 10⁻⁶]
L = 0.054 / [0.0366 × 10⁻⁶]
L = 1.47 × 10⁶
Maximum altitude to see(L) = 1.47 × 10⁶ m (Approx)
What is the thinnest soap film (excluding the case of zero thickness) that appears black when illuminated with light with a wavelength of 580 nm
Answer:
Explanation:
In case of soap film , light gets reflected from denser medium , hence interference takes place between two waves , one reflected from upper and second from lower surface . For destructive interference the condition is
2μt = nλ where μ is refractive index of water , t is thickness , λ is wavelength of light and n is an integer .
2 x 1.34 x t = 1 x 580
t = 216.42 nm .
Thickness must be 216.42 nm .
Which statement accurately describes the inner planets? Uranus is one of the inner planets. The inner planets formed when the solar system cooled. The inner planets are also called terrestrial planets. The inner planets are larger than the outer planets.
The correct answer is C. The inner planets are also called terrestrial planets.
Explanation:
Our solar system includes a total of eight planets. Additionally, planets are classified into broad categories including inner planets and outer planets. The inner planets category applies to planets such as Earth, Mercury, or Mars because these are located within the asteroid belt (region of asteroids between Mars and Jupiter). Moreover, inner planets differ from others due to their composition as they are composed of rocks and metals. Also, due to this composition, these are known as terrestrial planets. According to this, the statement that best describes inner planets is "The inner planets are also called terrestrial planets".
Answer:
The answer is c.) The inner planets are also called terrestrial planets.
Explanation:
A small omnidirectional stereo speaker produces waves in all directions that have an intensity of 8.00 at a distance of 4.00 from the speaker.
At what rate does this speaker produce energy?
What is the intensity of this sound 9.50 from the speaker?
What is the total amount of energy received each second by the walls (including windows and doors) of the room in which this speaker is located?
Answer:
A. We have that radius r = 4.00m intensity I = 8.00 W/m^
total power = power/ Area ( 4πr2)= 8.00 w/m^2( 4π ( 4.00 m)2=1607.68 W
b) I = total power/ 4πr2= 8.00 W/m2 ( 4.00 m/ 9.5 m)2= 1.418 W/m2
c) E = total power x time= 1607 . 68 W x 1s= 1607.68 J
A car travels at 45 km/h. If the driver breaks 0.65 seconds after seeing the traffic light turn yellow, how far will the car continue to travel before it begins to slow?
Answer:
8.1 m
Explanation:
Convert km/h to m/s.
45 km/h × (1000 m/km) × (1 h / 3600 s) = 12.5 m/s
Distance = speed × time
d = (12.5 m/s) (0.65 s)
d = 8.125 m
An air-filled capacitor consists of two parallel plates, each with an area of 7.60 cm^2, separated by a distance of 1.70 mm. A 25.0-V potential difference is applied to these plates. Calculate: a. the electric field between the plates b. the surface charge density c. the capacitance d. the charge on each plate.
Answer:
(a) 1.47 x 10⁴ V/m
(b) 1.28 x 10⁻⁷C/m²
(c) 3.9 x 10⁻¹²F
(d) 9.75 x 10⁻¹¹C
Explanation:
(a) For a parallel plate capacitor, the electric field E between the plates is given by;
E = V / d -----------(i)
Where;
V = potential difference applied to the plates
d = distance between these plates
From the question;
V = 25.0V
d = 1.70mm = 0.0017m
Substitute these values into equation (i) as follows;
E = 25.0 / 0.0017
E = 1.47 x 10⁴ V/m
(c) The capacitance of the capacitor is given by
C = Aε₀ / d
Where
C = capacitance
A = Area of the plates = 7.60cm² = 0.00076m²
ε₀ = permittivity of free space = 8.85 x 10⁻¹²F/m
d = 1.70mm = 0.0017m
C = 0.00076 x 8.85 x 10⁻¹² / 0.0017
C = 3.9 x 10⁻¹²F
(d) The charge, Q, on each plate can be found as follows;
Q = C V
Q = 3.9 x 10⁻¹² x 25.0
Q = 9.75 x 10⁻¹¹C
Now since we have found other quantities, it is way easier to find the surface charge density.
(b) The surface charge density, σ, is the ratio of the charge Q on each plate to the area A of the plates. i.e
σ = Q / A
σ = 9.75 x 10⁻¹¹ / 0.00076
σ = 1.28 x 10⁻⁷C/m²
A competitive diver leaves the diving board and falls toward the water with her body straight and rotating slowly. She pulls her arms and legs into a tight tuck position. What happens to her rotational kinetic energy
Answer: her rotational kinetic energy increases
Light of wavelength 500 nm falls on two slits spaced 0.2 mm apart. If the spacing between the first and third dark fringes is to be 4.0 mm, what is the distance from the slits to a screen?
Answer:
L = 0.8 m
Explanation:
Since, the distance between first and third dark fringes is 4 mm. Therefore, the fringe spacing between consecutive dark fringes will be:
Δx = 4 mm/2 = 2 mm = 2 x 10⁻³ m
but,
Δx = λL/d
λ = wavelength of the light = 500 nm = 5 x 10⁻⁷ m
d = slit spacing = 0.2 mm = 0.2 x 10⁻³ m
L = Distance between slits and screen = ?
Therefore, using the values, we get:
2 x 10⁻³ m = (5 x 10⁻⁷ m)(L)/(0.2 x 10⁻³)
L = (2 x 10⁻³ m)(0.2 x 10⁻³ m)/(5 x 10⁻⁷ m)
L = 0.8 m
Matter's resistance to a change in motion is called _____ and is directly proportional to the mass of an object
Answer:
Matter's resistance to a change in motion is called INERTIA and is directly proportional to the mass of an object.
Explanation:
A load of 1 kW takes a current of 5 A from a 230 V supply. Calculate the power factor.
Answer:
Power factor = 0.87 (Approx)
Explanation:
Given:
Load = 1 Kw = 1000 watt
Current (I) = 5 A
Supply (V) = 230 V
Find:
Power factor.
Computation:
Power factor = watts / (V)(I)
Power factor = 1,000 / (230)(5)
Power factor = 1,000 / (1,150)
Power factor = 0.8695
Power factor = 0.87 (Approx)
What happens to the deflection of the galvanometer needle (due to moving the magnet) when you increase the number of loops
Answer:
If the magnet is moved, the galvanometer needle will deflect, showing that current is flowing through the coil which will increase total induced electromotive force
Explanation:
galvanometer is an instrument that can detect and measure small current in an electrical circuit.
If the magnet is moved, the galvanometer needle will deflect, showing that current is flowing through the coil. If it is move in a way into the coil,the needle deflect in that way and if it move in another way, it will deflect in the other way.
The total induced emf is equal to the emf induced in each loop by the changing magnetic flux, then multiplied by the number of loops and an increase in the number of loops will cause increase in the total induced emf.
Water flows at speed v in a pipe of radius R. At what speed does the water flow through a constriction in which the radius of the pipe is R/3
Answer:
v₂ = 9 v
Explanation:
For this exercise in fluid mechanics, let's use the continuity equation
v₁ A₁ = v₂ A₂
where v is the velocity of the fluid, A the area of the pipe and the subscripts correspond to two places of interest.
The area of a circle is
A = π R²
let's use the subscript 1 for the starting point and the subscript 2 for the part with the constraint
In this case v₁ = v and the area is
A₁ = π R²
in the second point
A₂= π (R / 3)²
we substitute in the continuity equation
v π R² = v₂ π R² / 9
v = v₂ / 9
v₂ = 9 v
A 750 gram grinding wheel 25.0 cm in diameter is in the shape of a uniform solid disk. (we can ignore the small hole at the center). when it is in use, it turns at a consant 220 rpm about an axle perpendicular to its face through its center. When the power switch is turned off, you observe that the wheel stops in 45.0 s with constant angular acceleration due to friction at the axle. What torque does friction exert while this wheel is slowing down?
Answer:
Torque = 0.012 N.m
Explanation:
We are given;
Mass of wheel;m = 750 g = 0.75 kg
Radius of wheel;r = 25 cm = 0.25 m
Final angular velocity; ω_f = 0
Initial angular velocity; ω_i = 220 rpm
Time taken;t = 45 seconds
Converting 220 rpm to rad/s we have;
220 × 2π/60 = 22π/3 rad/s
Equation of rotational motion is;
ω_f = ω_i + αt
Where α is angular acceleration
Making α the subject, we have;
α = (ω_f - ω_i)/t
α = (0 - 22π/3)/45
α = -0.512 rad/s²
The formula for the Moment of inertia is given as;
I = ½mr²
I = (1/2) × 0.75 × 0.25²
I = 0.0234375 kg.m²
Formula for torque is;
Torque = Iα
For α, we will take the absolute value as the negative sign denotes decrease in acceleration.
Thus;
Torque = 0.0234375 × 0.512
Torque = 0.012 N.m
A wire of 5.8m long, 2mm diameter carries 750ma current when 22mv potential difference is applied at its ends. if drift speed of electrons is found then:_________.
(a) The resistance R of the wire(b) The resistivity p, and(c) The number n of free electrons per unit volume.
Explanation:
According to Ohms Law :
V = I * R
(A) R (Resistance) = 0.022 / 0.75 = 0.03 Ohms
Also,
[tex]r = \alpha \frac{length}{area} = \alpha \frac{5.8}{3.14 \times 0.001 \times 0.001} [/tex]
(B)
[tex] \alpha(resistivity) = 1.62 \times {10}^{ - 8} [/tex]
Drift speed is missing. It is given as;
1.7 × 10^(-5) m/s
A) R = 0.0293 ohms
B) ρ = 1.589 × 10^(-8)
C) n = 8.8 × 10^(28) electrons
This is about finding, resistance and resistivity.
We are given;Length; L = 5.8 m
Diameter; d = 2mm = 0.002 m
Radius; r = d/2 = 0.001 m
Voltage; V = 22 mv = 0.022 V
Current; I = 750 mA = 0.75 A
Area; A = πr² = 0.001²π
Drift speed; v_d = 1.7 × 10^(-5) m/s
A) Formula for resistance is;R = V/I
R = 0.022/0.75
R = 0.0293 ohms
B) formula for resistivity is given by;ρ = RA/L
ρ = (0.0293 × 0.001²π)/5.8
ρ = 1.589 × 10^(-8)
C) Formula for current density is given by;J = n•e•v_d
Where;
J = I/A = 0.75/0.001²π A/m² = 238732.44 A/m²
e is charge on an electron = 1.6 × 10^(-19) C
v_d = 1.7 × 10^(-5) m/s
n is number of free electrons per unit volume
Thus;
238732.44 = n(1.6 × 10^(-19) × 1.7 × 10^(-5))
238732.44 = (2.72 × 10^(-24))n
n = 238732.44/(2.72 × 10^(-24))
n = 8.8 × 10^(28)
Read more at; brainly.com/question/17005119
If one could transport a simple pendulum of constant length from the Earth's surface to the Moon's, where acceleration due to gravity is one-sixth (1/6) that on the Earth, by what factor would be the pendulum frequency be changed
Answer:
The frequency will change by a factor of 0.4
Explanation:
T = 2(pi)*sqrt(L/g)
Since g(moon) = (1/6)g(earth), the period would change by sqrt[1/(1/6)] = sqrt(6) ~ 2.5 times longer on the moon. Since the period & frequency are inverses, the frequency would be 1/2.5 or 0.4 times shorter on the moon.
UVC light used in sterilizers, has wavelengths between 100 to 280 nm. If a certain UVC wave has a wavelength of 142.9 nm, what is the energy of one of its photons in J
Answer:
The energy of one of its photons is 1.391 x 10⁻¹⁸ J
Explanation:
Given;
wavelength of the UVC light, λ = 142.9 nm = 142.9 x 10⁻⁹ m
The energy of one photon of the UVC light is given by;
E = hf
where;
h is Planck's constant = 6.626 x 10⁻³⁴ J/s
f is frequency of the light
f = c / λ
where;
c is speed of light = 3 x 10⁸ m/s
λ is wavelength
substitute in the value of f into the main equation;
E = hf
[tex]E = \frac{hc}{\lambda} \\\\E = \frac{6.626*10^{-34} *3*10^{8}}{142.9*10^{-9}} \\\\E = 1.391*10^{-18} \ J[/tex]
Therefore, the energy of one of its photons is 1.391 x 10⁻¹⁸ J
A resistor made of Nichrome wire is used in an application where its resistance cannot change more than 1.35% from its value at 20.0°C. Over what temperature range can it be used (in °C)?
Answer:
Pls seeattached file
Explanation:
A resistor made of Ni chrome wire is used in an application where its resistance cannot be more than 1.35 % so its temperature range will be from 33.75 to -33.75 °C.
What is Resistance?Electrical resistance, or resistance to electricity, is a force that opposes the flow of current. Ohms are used to expressing resistance values.
When there is an electron difference between two terminals, electricity will flow from high to low. In opposition to that flow is resistance. As resistance rises, the current declines. On the other side, when the resistance falls, the current rises.
According to the question,
R = R₀ (1 + α ΔT)
(1 + 0.0135)R₀ = R₀(1 + α ΔT)
ΔT = (1 + 0.0135) / α
= 0.0135 / 0.0004
= 33.75 °C.
ΔT = [(1 - 0.0135) -1]/0.004
= -33.75 °C
To get more information about Resistance :
https://brainly.com/question/11431009
#SPJ5
A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .Part A. Calcualte the coil's self-inductance.Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf froma to b or from b to a?
Complete Question
A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .
Part A. Calculate the coil's self-inductance.
Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.
Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf from a to b or from b to a?
Answer:
Part A
[tex]L = 0.000863 \ H[/tex]
Part B
[tex]\epsilon = 0.863 \ V[/tex]
Part C
From terminal a to terminal b
Explanation:
From the question we are told that
The number of turns is [tex]N = 590 \ turns[/tex]
The cross-sectional area is [tex]A = 6.20 cm^2 = 6.20 *10^{-4} \ m[/tex]
The radius is [tex]r = 5.0 \ cm = 0.05 \ m[/tex]
Generally the coils self -inductance is mathematically represented as
[tex]L = \frac{ \mu_o N^2 A }{2 \pi * r }[/tex]
Where [tex]\mu_o[/tex] is the permeability of free space with value [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]
substituting values
[tex]L = \frac{ 4\pi * 10^{-7} * 590^2 6.20 *10^{-4} }{2 \pi * 0.05 }[/tex]
[tex]L = \frac{ 2 * 10^{-7} * 590^2 6.20 *10^{-4} }{ 0.05 }[/tex]
[tex]L = 0.000863 \ H[/tex]
Considering the Part B
Initial current is [tex]I_1 = 5.00 \ A[/tex]
Current at time t is [tex]I_t = 3.0 \ A[/tex]
The time taken is [tex]\Delta t = 3.00 ms = 0.003 \ s[/tex]
The self-induced emf is mathematically evaluated as
[tex]\epsilon = L * \frac{\Delta I}{ \Delta t }[/tex]
=> [tex]\epsilon = L * \frac{ I_1 - I_t }{ \Delta t }[/tex]
substituting values
[tex]\epsilon = 0.000863 * \frac{ 5- 2 }{ 0.003 }[/tex]
[tex]\epsilon = 0.863 \ V[/tex]
The direction of the induced emf is from a to b because according to Lenz's law the induced emf moves in the same direction as the current
This question involves the concepts of the self-inductance, induced emf, and Lenz's Law
A. The coil's self-inductance is "0.863 mH".
B. The self-induced emf in the coil is "0.58 volts".
C. The direction of the induced emf is "from b to a".
A.
The self-inductance of the coil is given by the following formula:
[tex]L=\frac{\mu_oN^2A}{2\pi r}[/tex]
where,
L = self-inductance = ?
[tex]\mu_o[/tex] = permeability of free space = 4π x 10⁻⁷ N/A²
N = No. of turns = 590
A = Cross-sectional area = 6.2 cm² = 6.2 x 10⁻⁴ m²
r = radius = 5 cm = 0.05 m
Therefore,
[tex]L=\frac{(4\pi\ x\ 10^{-7}\ N/A^2)(590)^2(6.2\ x\ 10^{-4}\ m^2)}{2\pi(0.05\ m)}[/tex]
L = 0.863 x 10⁻³ H = 0.863 mH
B.
The self-induced emf is given by the following formula:
[tex]E=L\frac{\Delta I}{\Delta t}\\\\[/tex]
where,
E = self-induced emf = ?
ΔI = change in current = 2 A
Δt = change in time = 3 ms = 0.003 s
Therefore,
[tex]E=(0.000863\ H)\frac{2\ A}{0.003\ s}[/tex]
E = 0.58 volts
C.
According to Lenz's Law, the direction of the induced emf always opposes the change in flux that causes it. Hence, the direction of the induced emf will be from b to a.
Learn more about Lenz's Law here:
https://brainly.com/question/12876458?referrer=searchResults
An unstable particle at rest spontaneously breaks into two fragments of unequal mass. The mass of the first fragment is 3.00 10-28 kg, and that of the other is 1.86 10-27 kg. If the lighter fragment has a speed of 0.844c after the breakup, what is the speed of the heavier fragment
Answer: Speed = [tex]3.10^{-31}[/tex] m/s
Explanation: Like in classical physics, when external net force is zero, relativistic momentum is conserved, i.e.:
[tex]p_{f} = p_{i}[/tex]
Relativistic momentum is calculated as:
p = [tex]\frac{mu}{\sqrt{1-\frac{u^{2}}{c^{2}} } }[/tex]
where:
m is rest mass
u is velocity relative to an observer
c is light speed, which is constant (c=[tex]3.10^{8}[/tex]m/s)
Initial momentum is zero, then:
[tex]p_{f}[/tex] = 0
[tex]p_{1}-p_{2}[/tex] = 0
[tex]p_{1} = p_{2}[/tex]
To find speed of the heavier fragment:
[tex]\frac{mu_{1}}{\sqrt{1-\frac{u^{2}_{1}}{c^{2}} } }=\frac{mu_{2}}{\sqrt{1-\frac{u^{2}_{2}}{c^{2}} } }[/tex]
[tex]\frac{1.86.10^{-27}u_{1}}{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } }=\frac{3.10^{-28}.0.844.3.10^{8}}{\sqrt{1-\frac{(0.844c)^{2}}{c^{2}} } }[/tex]
[tex]\frac{1.86.10^{-27}u_{1}}{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } }=1.42.10^{-19}[/tex]
[tex]1.86.10^{-27}u_{1} = 1.42.10^{-19}.{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } }[/tex]
[tex](1.86.10^{-27}u_{1})^{2} = (1.42.10^{-19}.{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } })^{2}[/tex]
[tex]3.46.10^{-54}.u_{1}^{2} = 2.02.10^{-38}.(1-\frac{u_{1}^{2}}{9.10^{16}} )[/tex]
[tex]3.46.10^{-54}.u_{1}^{2} = 2.02.10^{-38} -[2.02.10^{-38}(\frac{u_{1}^{2}}{9.10^{16}} )][/tex]
[tex]3.46.10^{-54}.u_{1}^{2} = 2.02.10^{-38} -2.24.10^{-23}.u^{2}_{1}[/tex]
[tex]3.46.10^{-54}.u_{1}^{2}+2.24.10^{-23}.u^{2}_{1} = 2.02.10^{-38}[/tex]
[tex]2.24.10^{-23}.u^{2}_{1} = 2.02.10^{-38}[/tex]
[tex]u^{2}_{1} = \frac{2.02.10^{-38}}{2.24.10^{-23}}[/tex]
[tex]u_{1} = \sqrt{9.02.10^{-62}}[/tex]
[tex]u_{1} = 3.10^{-31}[/tex]
The speed of the heavier fragment is [tex]u_{1} = 3.10^{-31}[/tex]m/s.
A nearsighted person has a far point that is 4.2 m from his eyes. What focal length lenses in diopters he must use in his contacts to allow him to focus on distant objects?
Answer:
-0.24diopters
Explanation:
The lens is intended that makes an object at infinity appear to be 4.2 m away, so do=infinity, dI = - 4.2m (minus sign because image is on same side of lens as object)
So 1/do +1/di = 1/f
1/infinity + 1/-4.2 = 1/f
1/f = 1/-4.2 = -0.24diopters
3. What are the first steps that you should take if you are unable to get onto the Internet? (1 point)
O Check your router connections then restart your router.
O Plug the CPU to a power source and reboot the computer.
O Adjust the display properties and check the resolution.
Use the Control Panel to adjust the router settings.
Answer:
Check your router connections then restart your router.
Explanation:
Answer:
Check your router connections then restart your router.
Explanation:
Most internet access comes from routers so the problem is most likely the router.
A 70 kg man floats in freshwater with 3.2% of his volume above water when his lungs are empty, and 4.85% of his volume above water when his lungs are full.
Required:
a. Calculate the volume of air he inhales - called his lung capacity - in liters.
b. Does this lung volume seem reasonable?
Answer:
Explanation:
A) Vair = 1.3 L
B) Volume is not reasonable
Explanation:
A)
Assume
m to be total mass of the man
mp be the mass of the man that pulled out of the water
m1 be the mass above the water with the empty lung
m2 be the mass above the water with full lung
wp be the weight that the buoyant force opposes as a result of the air.
Va be the volume of air inside man's lungs
Fb be the buoyant force due to the air in the lung
given;
m = 78.5 kg
m1 = 3.2% × 78.5 = 2.5 kg
m2 = 4.85% × 78.5 = 3.8kg
But, mp = m2- m1
mp = 3.8 - 2.5
mp = 1.3kg
So using
Archimedes principle, the relation for formula for buoyant force as;
Fb = (m_displaced water)g = (ρ_water × V_air × g)
Where ρ_water is density of water = 1000 kg/m³
Thus;
Fb = wp = 1.3× 9.81
Fb = 12.7N
But
Fb = (ρ_water × V_air × g)
So
Vair = Fb/(ρ_water × × g)
Vair = 12.7/(1000 × 9.81)
V_air = 1.3 × 10^(-3) m³
convert to litres
1 m³ = 1000 L
Thus;
V_air = 1.3× 10^(-3) × 1000
V_air = 1.3 L
But since the average lung capacity of an adult human being is about 6-7litres of air.
Thus, the calculated lung volume is not reasonable
Explanation:
