Answer:
Pressure
Explanation:
One of the theories propounded by the Kinetic molecular theory, and which also provides an explanation of the several gas laws, is the statement that the gas molecules in a container, travel in straight lines and are in constant collision with themselves and the walls of the container, thus exerting force. This force is the pressure which is defined as the force per unit area.
There is no loss of energy in the collisions involving the gas molecules and that is why their movement can be described as elastic. The descriptions of the behavior of gas molecules in the Kinetic Molecular Theory, give rise to Charles law, Boyle's Law, Avogadro's Laws, Dalton's Law, and Amonton's Law.
Answer:
The pressure
Explanation:
Molecules of gases are constantly in motion, colliding with the walls of their container. This constant collision impacts force on the walls of the container, which depends on the speed with which the molecules are moving. The speed with which these molecules travel depends on the average kinetic energy of the molecules, which is proportional to the temperature.
This force when exerted per unit area is the pressure the gases exert on the walls of the container.
Self-Check
por Learning
A truck mass 8000 kg and a car a mass 1000
kg are travelling at the same velocity. Which one has greater kinetic energy ? Why?
Answer:
K.E of truck > K.E of car
Explanation:
Mass of the truck = 8000Kg
K.E=[tex]\frac{1}{2} mv[/tex]
K.E =[tex]\frac{1}{2}*8000*v\\ 4000v[/tex]
Mass of the car = 1000 Kg
K.E of the car =[tex]\frac{1}{2}*1000*v\\ 500v[/tex]
Therefore Kinetic energy of the truck is greater than that of the car
Match the following:
Tailored software
. Utility software
Operating system
Software
Packaged software
Set of programs
Library management system
Scan viruses
Microsoft Office
used to coordinate the hardw
the computer
Answer:
1) Tailored software Library management system
2) Utility software Scan viruses
3) Operating system Used to coordinate the hardware of the computer
4) Packaged software set of programs Microsoft office
Explanation:
1) A tailored software, also known as a custom software, is one that is designed and tailor-made only for a particular organisation
2) A utility software is a computer maintenance and analysis software used to enable proper functioning of the computer by performing restorative and maintenance tasks
3) Operating system software
The operating system software controls the operation of the computer hardware within the system and enables the operation of other programs in the computer
4) Packaged software are a collection of programs that are oriented to perform interrelated tasks that a focused to a particular area, such as Microsoft Office.
Six members of a synchronized swim team wear earplugs to protect themselves against water pressure at depths, but they can still hear the music and perform the combinations in the water perfectly. One day, they were asked to leave the pool so the dive team could practice a few dives, and they tried to practice on a mat, but seemed to have a lot more difficulty. Why might this be
Answer:
The sound travels differently in different medium according the density of the medium.
Explanation:
The sound travels faster in dense medium and can be heard by the vibration of the bone present in the ear. The ear plugs reduce the sound intensity in both medium water and on land (air).
In air the sound is not heard properly due to the earplugs that stops the as the vibration are not able to produce as sound is not able to reach to middle ear, but Navy researchers have discovered that sound under water is heard by the bone present behind the ear, vibrations mastoid.
Matter must have two physical properties 1. Have mass, and 2
∆ Must move
∆ Use energy
∆ Take up space
∆ Be measure
able
Answer:
Take up space
Explanation:
Actually we know this by the definition of matter which states that "matter is any substance that has mass and takes up space by having volume."
hope it helped you:)
Which waves move fast Longitudinal waves or Transverse waves and why???
Answer:
Transverse wave
Explanation:
Its because in transverse wave the particle displacement is perpendicular to the direction of wave propagation..hope it helps you...
Shortly after receiving a traffic ticket for speeding, Fred made numerous comments about the road signs being inadequate and is GPS telling him a different speed limit. This would be an example of:
Answer:
External locus of control
Explanation:
External locus of control is an attitude people possess that makes them attribute their failures or successes to factors other than themselves. The opposite of this type of attitude is the Internal locus of control where the individuals take responsibility for the outcomes of their actions whether good or bad. One good thing about the external locus of control is that when the individuals with this characteristic record successes, they attribute it to others and this presents them as people with team spirit. However, when they record failures, they do not want to take the blame, but rather attribute it to others.
Fred exhibits an external locus of control because he attributed his speeding to other factors like the road signs and GPS instead of fully admitting that it was his fault.
Jaiden is writing a report about the structure of the atom in her report,she says that the atom has three main parts and two subatomic particles. Do you agree with her?why or why not
Answer:
I do not agree with the answer.
Because in reality, the atom has 2 main parts and 3 subatomic particles.
Explanation:
The parts of an atom are:
- The crust: It is the outer part of the atom and is the place where the electrons are.
- The nucleus: It is the central part of the atom and is the place that contains the protons and neutrons.
The subatomic particles of the atom are:
- Electrons: They are negatively charged particles that go in the atom's crust and are divided into specific sections.
- Protons: They are particles with a positive electric charge, the number of protons in the nucleus of an atom is what determines the atomic number of an element.
- Neutrons: They are atoms with no electric charge.
A 1.00-kg glider attached to a spring with a force constant 25.0 N/m oscillates on a frictionless, horizontal air track. At t = 0, the glider is released from rest at x = -2.80 cm (that is, the spring is compressed by 2.80 cm). (a) Find the period of the glider's motion. How does the period depend on the mass and the spring constant? Does it depend on the amplitude of oscillation? s (b) Find the maximum values of its speed and acceleration. speed m/s acceleration m/s2 (c) Find the position, velocity, and acceleration as functions of time. (Where position is in m, velocity is in m/s, acceleration is in m/s2, and t is in s. Use the following as necessary: t.) x(t) = v(t) = a(t) =
Answer:
a) T = 1.26 s , b) v_max = 0.14 m / s , a_max = 0.7 m / s²
c) x = 0.028 cos (5 t) , v = - 0.14 sin 5t, a = - 0.7 cos 5t
Explanation:
This is a simple harmonic motion exercise that is described by the equation
x = A cos (wt +Ф)
with
w = √ (k / m)
let's apply this expression to our case
a) Angular velocity is related to frequency
w = 2π f
frequency and period are related
f = 1 / T
we substitute
2π / T = √ (k / m)
T = 2π √(m / k)
let's calculate
T = 2π √(1/25)
T = 1.26 s
In the expression for the period, the amplitude does not appear, therefore there is no dependence, as long as Hooke's law is fulfilled, which is correct for small amplitudes.
b) in the initial equation we have the position as a function of time, let's use the definition of speed and acceleration
v = dx / dt
v = - A w sin (wt + Ф)
the speed is maximum when the sine is -1
v_max = A w
w = √ (k / m)
w = √ 25/1
w = 5 rad / s
the amplitude of the movement is equal to the maximum compression of the spring
A = 2.8 cm = 0.028 m
we substitute
v_max = 0.028 5
v_max = 0.14 m / s
acceleration
a = dv / dt
a = - A w² cos (wt + Ф)
the acceleration is maximum when the cosine is -1
a_max = A w²
let's calculate
a_max = 0.028 5²
a_max = 0.7 m / s²
c) let's start by finding the phase constant
v = -A w cos (wt + Ф)
at t = 0 they indicate that the system has v = 0
0 = -A w sin (0 + Ф)
Ф = sin⁻¹ 0
Ф = 0
we write the equation
x = 0.028 cos (5 t)
v = - A w sin (wt + Ф)
v = - 0.028 5 sin (5t + 0)
v = - 0.14 sin 5t
acceleration
a = - A w² cos (wt + Ф)
a = - 0.028 5 2 cos (5 t + 0)
a = - 0.7 cos 5t
A narrow beam of light containing red (660 nm) and blue (470 nm) wavelengths travels from air through a 1.00 cm thick flat piece of crown glass and back to air again. The beam strikes at an incident angle of 30 degrees. (a) At what angles do the two colors emerge
Answer:
The color blue emerges at 19.16° and the color red emerges at 19.32°.
Explanation:
The angle at which the two colors emerge can be calculated using the Snell's Law:
[tex]n_{1}sin(\theta_{1}) = n_{2}sin(\theta_{2})[/tex]
Where:
n₁ is the refractive index of the incident medium (air) = 1.0003
n₂ is the refractive index of the refractive medium:
blue light in crown glass = 1.524
red light in crown glass = 1.512
θ₁ is the angle of the incident light = 30°
θ₂ is the angle of the refracted light
For the red wavelengths we have:
[tex] \theta_{2} = arcsin(\frac{n_{1}sin(\theta_{1})}{n_{2}}) = arcsin(\frac{1.0003*sin(30)}{1.512}) = 19.32 ^{\circ} [/tex]
For the blue wavelengths we have:
[tex] \theta_{2} = arcsin(\frac{n_{1}sin(\theta_{1})}{n_{2}}) = arcsin(\frac{1.0003*sin(30)}{1.524}) = 19.16 ^{\circ} [/tex]
Therefore, the color blue emerges at 19.16° and the color red emerges at 19.32°.
I hope it helps you!
You are hiking in a canyon and you notice an echo. You decide to let out a yell and notice it took 2 seconds before you heard the echo of your yell. How far away is the canyon wall that reflected your yell
Answer:
d = 343 m
Explanation:
Given that,
You notice that an echo took 2 seconds before you heard the echo of your yell.
We need to find that how far away is the canyon wall that reflected your yell. It means we need to find the distance.
The distance covered by an object is given by :
d = v × t
v is speed of sound in air, v = 343 m/s
The sound took 1 s to reach the wall and 1 s back to you.
It means that,
d = 343 × 1
d = 343 m
So, canyon will reflect your yell at a distance of 343 m
You are the driver of the car in the photos above. You Are traveling at 30 mph when suddenly the car goes from its position in the first photo to the position in the second photo. What is happening
Answer:
the car uses teleportation, to zip to one side of the photo, to the other
Explanation:
Question is on the picture. Answers: A. 0.1 J/g*C B. 0.2 J/g*C C. 0.4 J/g*C D. 4 J/g*C
Answer:
B. 0.2 J/g/°C
Explanation:
The solid phase is the first segment (from 0°C to 50°C).
q = mCΔT
200 J = (20 g) C (50°C)
C = 0.2 J/g/°C
State 1 difference between 1 way rotary motion and reversible rotary motion
Answer:
The difference between One-way as well as reversible rotary motion is described below.
Explanation:
Unless rotary motions occur restricted to single direction exclusively (i.e. whether clockwise as well as anti-clockwise only), it is defined as another rotary 'one-way' motion.This motor establishes that continuously variable movement at 360 ° chemically guided is conceivable. The rotating is regulated, and for a particular direction, the biochemical occurrences guiding rotation become incredibly selective.Which of the following illustrates an increase in potential energy? Group of answer choices a wind-up toy winding down a person climbs a set of stairs an apple dropping from a tree a firecracker explodes
Answer:
A person climbs a set of stairs
Explanation:
Potential energy is said to be possessed by an object due to its position. As the height from the ground level increase, the potential energy increases. It is calculated by the below formula as :
P = mgh
Out of the given options, the option that illustrates an increase in potential energy is option (b) i.e. a person climbs a set of stairs. As he steps one stair, its position from ground increases. It means its potential energy increases.
element X has two isotopes: X-27 and x-29. x-27 has an atomic mass of 26.975 and a relative abundance of 82.33%, and X-29 has an atomic mass of 29.018 and a relative abundance of 17.67%. calculate the atomic mass of element X. show your work
Answer:
27.34 (no unit)
Explanation:
26.975*82.33%+29.018*17.67%
=27.34
Dennis throws a volleyball up in the air. It reaches its maximum height 1.1\, \text s1.1s1, point, 1, start text, s, end text later. We can ignore air resistance. What was the volleyball's velocity at the moment it was tossed into the air?
Answer:
If max height = 1.1 meters, then initial velocity is 3.28 m/s
If max height is 1.1 feet, then the initial velocity is 5.93 ft/s
Explanation:
Recall the formulas for vertical motion under the acceleration of gravity;
for the vertical velocity of the object we have
[tex]v=v_0-g \,t[/tex]
for the object's vertical displacement we have
[tex]y-y_0=v_0\,t - \frac{g}{2} \,t^2[/tex]
If the maximum height reached by the object is given in meters, we use the value for g in [tex]m/s^2[/tex] which is: [tex]9.8\,\,m/s^2[/tex]
If the maximum height of the object is given in feet, we use the value for g in [tex]ft/s^2[/tex] which is : [tex]32\,\,ft/s^2[/tex]
Now, when the ball reaches its maximum height, the ball's velocity is zero, so that allows us to solve for the time (t) the process of reaching the max height takes:
[tex]v=v_0-g \,t\\0=v_0-g \,t\\g\,\,t=v_0\\t=\frac{v_0}{g}[/tex]
and now we use this to express the maximum height in the second equation we typed:
[tex]y-y_0=v_0\,t - \frac{g}{2} \,t^2\\max\,height=v_0\,(\frac{v_0}{g}) - \frac{g}{2} \,(\frac{v_0}{g})^2\\max\,height= \frac{v_0^2}{2\,g}[/tex]
Then if the max height is 1.1 meters, we use the following formula to solve for [tex]v_0[/tex]:
[tex]1.1= \frac{v_0^2}{2\,9.8}\\(9.8)\,(1.1)=v_0^2\\v_0=10.78\\v_0=\sqrt{10.78} \\v_0=3.28\,\,m/s[/tex]
If the max height is 1.1 feet, we use the following formula to solve for [tex]v_0[/tex]:
[tex]1.1= \frac{v_0^2}{2\,32}\\(32)\,(1.1)=v_0^2\\v_0=35.2\\v_0=\sqrt{35.2} \\v_0=5.93\,\,ft/s[/tex]
Answer:
11
Explanation:
for khan academy, this is the answer
A bicycle has a momentum of 36 kg • m/s and a velocity of 4 m/s. What is the mass of the bicycle? 9 kg 32 kg 40 kg 144 kg
Answer:
9 kg
Explanation:
Momentum is mass times velocity.
p = mv
36 kgm/s = m (4 m/s)
m = 9 kg
The mass of the bicycle is 9 kg.
Momentum of the bicycle
The momentum of the bicycle is the product of mass and velocity of the bicycle.
P = mv
where;
P is momentumm is mass v is velocitym = P/v
m = 36/4
m = 9 kg
Thus, the mass of the bicycle is 9 kg.
Learn more about momentum here: https://brainly.com/question/7538238
What two factors determine how much potential energy an object has?
Answer:
The mass of the object and its height in the gravitational field of the Earth.
Explanation:
If we are talking about gravitational potential energy which is defined as:
[tex]U=m\,*\,g\,*\,h[/tex]
being "m" the object's mass, "g" the acceleration due to gravity, and "h" the height at which the object is located relative to the conventionally picked level for zero of potential energy.
As long as the value of "g" is constant, the only two variables that determine the gravitational potential energy are the mass (m) of the object and its relative height (h).
Answer:
The objects weight and height above Earth's surface
Explanation:
K12 :)
Question 5
Calculate the kinetic energy of a car (m - 800 kg) moving at 15 m/s. Write your answer to the nearest whole number in the blank space
provided. Only write the numerical value of the answer without units. Do not leave any space in between numbers.
Answer: Joules
Answer:
90,000Explanation:
[tex]m =800kg\\v = 15\\\\K.E = \frac{1}{2}mv^2\\ K.E= \frac{1}{2} \times 800\times 15^2\\= 400 \times 225\\= 90000 joules\\= 90 kilojoules[/tex]
Which of the following best describes a consumer?
0. a business owner who sells clothes
0. someone who studies economics
O. a farmer who sells his crops
O. a person who buys goods and services
Answer:
a business who buys goods and services
an object weights 0.250 kgf in air 0.150 in water and 0.125 in an oil.find out the density of the object and the oil
Answer:
1) The density of the object = 2500 kg/m³
2) The density of the oil = 1250 kg/m³
Explanation:
1) The information relating to the question are;
The mass of the object in air = 0.250 kgf
The mass of the object in water = 0.150 kgf
The mass of the object in the oil = 0.125 kgf
By Archimedes's principle, we have;
The upthrust on the object in water = Mass in air - mass in water = The weight of the water displaced
The upthrust on the object in water = 0.250 - 0.150 = 0.1 kgf
∴ The weight of the water displaced = 0.1 kgf
Given that the object is completely immersed in the water, we have;
The volume of the water displaced = The volume of the object
The volume of 0.1 kg of water water displaced = Mass of the water/(Density of water)
The volume of 0.1 kg of water = 0.1/1000 = 0.0001 m³
The density of the object = (Mass in air)/ volume = 0.250/0.0001 = 2500 kg/m³
The density of the object = 2500 kg/m³
2) Whereby the mass of the object in the oil = 0.125 kgf
The upthrust of the oil = The weight of the oil displaced
The upthrust of the oil on the object = Mass of the object in air - mass of the object in the oil
The upthrust of the oil on the object = 0.250 - 0.125 = 0.125 kgf
The weight of the oil displaced = The upthrust of the oil
Given that the volume of the oil displaced = The volume of the oil, we have;
The volume of the oil displaced = 0.0001 m³
The mass of the 0.0001 m³ = 0.125 kg
Therefore the density of the oil = 0.125/0.0001 = 1250 kg/m³.
The density of the oil = 1250 kg/m³.
A person holds a 25 kg (250 newton) bag of cement over his head and moves it a distance of 10 m, taking 2 minutes, while another person carries it on a wheelbarrow that same distance, taking 1 minute.Who does more work ? What is the power of each person?
Explanation:
Assuming the 10 m distance is the vertical displacement, the work done by both people is the same.
Work = force × distance
W = (250 N) (10 m)
W = 2500 J
The power of the first person is:
Power = work / time
P = 2500 J / 120 s
P = 20.83 W
The power of the second person is:
P = 2500 J / 60 s
P = 41.67 W
the unit of energy is a derived unit
Explanation:
Hi, there!!
Energy is defined as the capacity or ability to do work. It's SI unit is Joule.
here,
Joule = (kg×m×m)/(s×s)
= kg×m^2/s^2.
Therefore, the derived unit is kg.m^2 by s^2.
Hope it helps...
whats suface tension
Answer: "Surface tension is a film of a liquid caused by the attraction of the particles in the surface layer by the bulk of the liquid, which tends to minimize surface area."
Hope this helps!
Answer:
Explanation:
Surface tension is the property of a liquid surface. It is an effect where the surface of the liquid is strong.
example - small insects can walk on water as they do not have enough weight to penetrate it.
This image might help you
Hope it helps
plz mark as brainliest!!!!!!!
please help ASAP.
these are examination questions ..
no nonsense answers .
i will mark as brainliest if you got it correct .
Answer:
1st question c part
2nd question c part
I need help pls now plleeeeeeeeaaassseeeee
Answer:
[tex]r = \frac{v}{i} = v = ri \\ i = \frac{v}{r} [/tex]
The pH scale is used to tell if a substance
is an acid or base. Substances with a pH
of 7 are neutral. An acid is anything
below 7 and a base is anything above 7.
Bleach has a pH of about 12. What type of
substance is bleach?
A. base
B. acid
C. neutral
Answer: Bleach is a base
Explanation: If bleach had a pH level of 12, a number above 7, than it is a base. Hope this helps!
fill in the blanks
1.)Seed drill is used for ____ of the seeds.
2.)ploughing helps the_____of roots of the growing plants.
3.)Tilling of the soil is also called a ________.
4.)Manure and fertilizers are use ti maintain the______of the soil.
5.)A most common weedicide is________.
6.)After harvesting,grains are separated from the chaffand hay by _______ or by using ______.
7.)The economial methods of irrigation are_____and____.
8.)The wild plants which grow along with the main crop are called_________.
9.) Shifting of tiny plants from a nursery to the main field is called______.
10.) Excess water and wet soil do not permit proper_____of the seeds or roots of the plants.
Answer:
1.) Sowing
2.) Respiration
3.) Soil preparation or cultivation or ploughing
4.) Fertility
5.) 2, 4 -D
6.) winnowing threshers
7.) Surface irrigation and sprinkler irrigation
8.) Weeds
9.) Transplantation
10.) Aeration
Explanation:
1.) Seed drill sows crop seed
2.) Ploughing assist in the respiration and penetration of the roots of a growing plants
3.) Tilling the soil is breaking of the soil lumps and turning of the soil
4.) Manure and fertilizers supply nutrient to the soil for the uptake by plant in food production
5.) 2, 4 -D are a range of weedicide containing 2,4-D as the active ingredient
6.) Winnowing is the separation of grain from straw
Threshers remove seeds from husks and stalks
7.) Surface irrigation -gravity enables the flow of the water
and sprinkler irrigation- Use of preset tools for irrigation
8.) Weeds are the unwanted, in situ, growing plants close to the crops
9.) Transplantation is the method of relocating plants
10.) Excess water limits access of the roots and seeds to atmospheric oxygen
A construction worker uses an electrical device to attract fallen nails and sharp objects
from a construction site. What is causing the attraction of the metal objects?
O An electrical wave oscillating perpendicular to the electrical device.
O An electrical charge radiating perpendicular to the wire
O Amagnetic wave radiating perpendicular to an electrical device
O A magnetic wave and electrical current moving in opposite directions
Answer:
is the last one, a magnetic wave and electrical current moving in opposite directions
Explanation:
opposite directions always attract in magnetic waves and fields
Suppose an experiment is designed to test the durability of batteries in different conditions. All of the batteries tested are double-A (AA) Brand X. All sets of batteries are preconditioned in different environmental conditions for exactly 168 hours (1 week).
Set 1: 0°C (freezing point of water)
Set 2: 24°C (approximately room temperature)
Set 3: 37°C (approximately body temperature)
The batteries are then continuously used to power identical mechanical drummer toys. As long as the toy keeps drumming the battery is considered functional. The drumming time for each toy is measured as an indication of battery durability. In this experiment, which condition is not controlled?
A.) temperature
B.) brand of batteries
C.) test for durability
D.) type of battery (battery size)
Answer:
I assume its c. Since its talking about testing.
Explanation:
Answer:
The answer is test of durability
Explanation:
