A small glass bead charged to 5.0 nC is in the plane that bisects a thin, uniformly charged, 10-cm-long glass rod and is 4.0 cm from the rod's center. The bead is repelled from the rod with a force of 910 N. What is the total charge on the rod?

Answers

Answer 1

Answer:

Explanation:

Let B= bead

Q = rod

the electric field at the glass bead pocation is

(Gauss theorem)

E = Q / (2 π d L εo)

the force is

F = q E = q Q / (2 π d L εo)

then

Q = 2 π d L εo F / q

Q = 2*3.14*4x10^-2*10^-1*8.85x10^-12*910x10^-4 / 5x10^-9 = 2.87x10^-8 C = 40.5 nC


Related Questions

A resistor made of Nichrome wire is used in an application where its resistance cannot change more than 1.35% from its value at 20.0°C. Over what temperature range can it be used (in °C)?

Answers

Answer:

Pls seeattached file

Explanation:

A resistor made of Ni chrome wire is used in an application where its resistance cannot be more than 1.35 % so its temperature range will be from 33.75 to -33.75 °C.

What is Resistance?

Electrical resistance, or resistance to electricity, is a force that opposes the flow of current. Ohms are used to expressing resistance values.

When there is an electron difference between two terminals, electricity will flow from high to low. In opposition to that flow is resistance. As resistance rises, the current declines. On the other side, when the resistance falls, the current rises.

According to the question,

R = R₀ (1 + α ΔT)

(1 + 0.0135)R₀ = R₀(1 + α ΔT)

ΔT = (1 + 0.0135) / α

= 0.0135 / 0.0004

= 33.75 °C.

ΔT = [(1 - 0.0135) -1]/0.004

= -33.75 °C

To get more information about Resistance :

https://brainly.com/question/11431009

#SPJ5

A sinusoidal electromagnetic wave is propagating in a vacuum in the +z-direction. If at a particular instant and at a certain point in space the electric field is in the +x-direction and has a magnitude of 4.00 V/m, what is the magnitude of the magnetic field of the wave at this same point in space and instant in time?

Answers

Answer:

B = 1.33 10⁻⁸ T , the magnetic field must be in the y + direction

Explanation:

In an electromagnetic wave the electric and magnetic fields are in phase

         c = E / B

         B = E / c

let's calculate

          B = 4.00 / 3 10⁸

          B = 1.33 10⁻⁸ T

To determine the direction we use that the electric and magnetic fields and the speed of the wave are perpendicular.

 If the wave advances in the + Z direction and the electric field is in the + x direction, the magnetic field must be in the y + direction

Exercise 2.4.5: Suppose we add possible friction to Exercise 2.4.4. Further, suppose you do not know the spring constant, but you have two reference weights 1 kg and 2 kg to calibrate your setup. You put each in motion on your spring and measure the frequency. For the 1 kg weight you measured 1.1 Hz, for the 2 kg weight you measured 0.8 Hz. a) Find k (spring constant) and c (damping constant). Find a formula for the mass in terms of the frequency in Hz. Note that there may be more than one possible mass for a given frequency. b) For an unknown object you measured 0.2 Hz, what is the mass of the object? Suppose that you know that the mass of the unknown object is more than a kilogram.

Answers

Answer:

a) k = 95.54 N / m,   c =   19.55 , b)      m₃ = 0.9078 kg

Explanation:

In a simple harmonic movement with friction, we can assume that this is provided by the speed

          fr = -c v

when solving the system the angular value remains

          w² = w₀² + (c / 2m)²

They give two conditions

1) m₁ = 1 kg

     f₁ = 1.1 Hz

the angular velocity is related to frequency

         w = 2π f₁

Let's find the angular velocity without friction is

         w₂ = k / m₁

we substitute

        (2π f₁)² = k / m₁ + (c / 2m₁)²

2) m₂ = 2 kg

    f₂ = 0.8 Hz

        (2π f₂)² = k / m₂ + (c / 2m₂)²

we have a system of two equations with two unknowns, so we can solve it

we solve (c / 2m)² is we equalize the expression

           (2π f₁)² - k / m₁ = (2π f₂²) 2 - k / m₁

           k (1 / m₂ - 1 / m₁) = 4π² (f₂² - f₁²)

           k = 4π² (f₂² -f₁²) / (1 / m₂ - 1 / m₁)

a) Let's calculate

           k = 4 π² (0.8² -1.1²) / (½ -1/1)

           k = 39.4784 (1.21) / (-0.5)

           k = 95.54 N / m

now we can find the constant of friction

              (2π f₁) 2 = k / m₁ + (c / 2m₁)²

           c2 = ((2π f₁)² - k / m₁) 4m₁²

           c2 = (4ππ² f₁² - k / m₁) 4 m₁²

let's calculate

           c² = (4π² 1,1² - 95,54 / 1) 4 1²

           c² = (47.768885 - 95.54) 8

           c² = -382.1689

           c =   19.55    

b) f₃ = 0.2 Hz

   m₃ =?

              (2πf₃)² = k / m₃ + (c / 2m₃) 2

we substitute the values

              (4π² 0.2²) = 95.54 / m₃ + 382.1689 2/4 m₃²

              1.579 = 95.54 / m₃ + 95.542225 / m₃²

let's call

              x = 1 / m₃

              x² = 1 / m₃²

- 1.579 + 95.54 x + 95.542225 x² = 0

              60.5080 x² + 60.5080 x -1 = 0

                x² + x - 1.65 10⁻² = 0

                  x = [1 ±√ (1- 4 (-1.65 10⁻²)] / 2

                  x = [1 ± 1.03] / 2

                  x₁ = 1.015 kg

                  x₂ = -0.015 kg

Since the mass must be positive we eliminate the second results

                  x₁ = 1 / m₃

                 m₃ = 1 / x₁

                  m₃ = 1 / 1.1015

             

If the
refractive index of benzere is 2.419,
what is the speed of light in benzene?

Answers

Answer:

[tex]v=1.24\times 10^8\ m/s[/tex]

Explanation:

Given that,

The refractive index of benzene is 2.419

We need to find the speed of light in benzene. The ratio of speed of light in vacuum to the speed of light in the medium equals the refractive index. So,

[tex]n=\dfrac{c}{v}\\\\v=\dfrac{c}{n}\\\\v=\dfrac{3\times 10^8}{2.419}\\\\v=1.24\times 10^8\ m/s[/tex]

So, the speed of light in bezene is [tex]1.24\times 10^8\ m/s[/tex].

Matter's resistance to a change in motion is called _____ and is directly proportional to the mass of an object

Answers

Answer:

Matter's resistance to a change in motion is called INERTIA and is directly proportional to the mass of an object.

Explanation:

Why was Bohr's atomic model replaced by the
modern atomic model?

Answers

Answer:

Explanation:

Bohr's atomic model was replaced by the  modern atomic model because of its limitations, which included :

(a) Only applicable for Hydrogen and like atoms ( He+1, Li+2 )

(b) Couldn't explain Zeeman Effect (splitting of spectral lines due external magnetic field ) and Stark Effect (splitting of spectral lines due to external electric field).

(c) Inconsistent with De-Broglie's Dual nature of matter and Heisenberg Uncertainty principal, etc.

At what angle should the axes of two Polaroids be placed so as to reduce the intensity of the incident unpolarized light to

Answers

Answer:

Ok, the question is incomplete buy ill try to answer this in a general way.

Suppose that you have no-polarized light.

When that light hits one polaroid, the light becomes polarized along some line, and has an intensity I0.

Now, when polarized light hits a polaroid which axis is at an angle θ with respect to the polarization of the light, the intensity of the resulting beam is given by the Malus's law:

I(θ) = I0*cos^2(θ)

For example, if the axis of the polaroid is exactly the same as the one of the polarized light, then we have θ = 0°

and:

I(0°) = I0*cos^2(0°) = I0

So the intensity does not change.

Now, knowing the initial intensity, you can find the angle needed to get a given intensity.

For example, if the question was:

"At what angle should the axes of two Polaroids be placed so as to reduce the intensity of the incident unpolarized light to A"

We should solve:

I(θ) = A = I0*cos^2(θ)

(A/i0) = cos^2(θ)

√(A/I0) = cos(θ)

Acos(√(A/I0)) = θ

You plan to take your hair blower to Europe, where the electrical outlets put out 240 V instead of the 120 V seen in the United States. The blower puts out 1700 W at 120 V.Required:a. What could you do to operate your blower via the 240V line in Europe? which one is it?b. What current will your blower draw from a European outlet?c. What resistance will your blower appear to have when operated at 240 ?

Answers

Answer:

a) Connect a series resistance of 8,47 ohms

b)14,16 [A]

c) r = 10,96 ohms

Explanation:

My blower requires 120 (v) then, I have to connect a series resistor to make the nominal 240 (v) of the European voltage outlet drop to 120 (V) but at the same time keep the level of current to operate my blower

In America

P = V*I

1700 (w) = 120*I

I = 1700/120 [A]

I = 14,16 [A]        current needed for the blower

In Europe

120 (v)  (the drop of voltage I need) when a current of 14,16 passes through to series  resistor is

V = I*R          120 = 14,16* R         R = 8,47 ohms

c) P = I*r²

1700 (w) = 14,16 (A) * r²

r² = 120,06

r = 10,96 ohms

Water flows at speed v in a pipe of radius R. At what speed does the water flow through a constriction in which the radius of the pipe is R/3

Answers

Answer:

   v₂ = 9 v

Explanation:

For this exercise in fluid mechanics, let's use the continuity equation

           v₁ A₁ = v₂ A₂

where v is the velocity of the fluid, A the area of ​​the pipe and the subscripts correspond to two places of interest.

The area of ​​a circle is

           A = π R²

let's use the subscript 1 for the starting point and the subscript 2 for the part with the constraint

     

In this case v₁ = v and the area is

            A₁ = π R²

in the second point

           A₂= π (R / 3)²

we substitute in the continuity equation

           v π R² = v₂ π R² / 9

            v = v₂ / 9

           

            v₂ = 9 v

An air-filled capacitor consists of two parallel plates, each with an area of 7.60 cm^2, separated by a distance of 1.70 mm. A 25.0-V potential difference is applied to these plates. Calculate: a. the electric field between the plates b. the surface charge density c. the capacitance d. the charge on each plate.

Answers

Answer:

(a) 1.47 x 10⁴ V/m

(b) 1.28 x 10⁻⁷C/m²

(c) 3.9 x 10⁻¹²F

(d) 9.75 x 10⁻¹¹C

Explanation:

(a) For a parallel plate capacitor, the electric field E between the plates is given by;

E = V / d               -----------(i)

Where;

V = potential difference applied to the plates

d = distance between these plates

From the question;

V = 25.0V

d = 1.70mm = 0.0017m

Substitute these values into equation (i) as follows;

E = 25.0 / 0.0017

E = 1.47 x 10⁴ V/m

(c) The capacitance of the capacitor is given by

C = Aε₀ / d

Where

C = capacitance

A = Area of the plates = 7.60cm² = 0.00076m²

ε₀ = permittivity of free space =  8.85 x 10⁻¹²F/m

d = 1.70mm = 0.0017m

C = 0.00076 x  8.85 x 10⁻¹² / 0.0017

C = 3.9 x 10⁻¹²F

(d) The charge, Q, on each plate can be found as follows;

Q = C V

Q =  3.9 x 10⁻¹² x 25.0

Q = 9.75 x 10⁻¹¹C

Now since we have found other quantities, it is way easier to find the surface charge density.

(b) The surface charge density, σ, is the ratio of the charge Q on each plate to the area A of the plates. i.e

σ = Q / A

σ = 9.75 x 10⁻¹¹ /  0.00076

σ = 1.28 x 10⁻⁷C/m²


Somebody please help it’s urgent!!!!

In the tug of war game, none of the teams won. What can you conclude about the forces of the two teams ? Write all the evidence to support your answer.

Answers

Answer:

Explanation:

We can conclude that the forces of the two teams are equal and opposite and hence they cancel each other. Therefore none of the teams won as the rope did not move.

hope this helps

plz mark as brainliest!!!!!!!

A string is stretched and fixed at both ends, 200 cm apart. If the density of the string is 0.015 g/cm, and its tension is 600 N, what is the wavelength (in cm) of the first harmonic?

Answers

Answer:

200cm

Explanation:

Answer:

100cm

Explanation:

Using

F= ( N/2L)(√T/u)

F1 will now be (0.5*2)( √600/0.015)

=> L( wavelength)= 200/2cm = 100cm

Which statement accurately describes the inner planets? Uranus is one of the inner planets. The inner planets formed when the solar system cooled. The inner planets are also called terrestrial planets. The inner planets are larger than the outer planets.

Answers

The correct answer is C. The inner planets are also called terrestrial planets.

Explanation:

Our solar system includes a total of eight planets. Additionally, planets are classified into broad categories including inner planets and outer planets. The inner planets category applies to planets such as Earth, Mercury, or Mars because these are located within the asteroid belt (region of asteroids between Mars and Jupiter). Moreover, inner planets differ from others due to their composition as they are composed of rocks and metals. Also, due to this composition, these are known as terrestrial planets. According to this, the statement that best describes inner planets is "The inner planets are also called terrestrial planets".

Answer:

The answer is c.) The inner planets are also called terrestrial planets.

Explanation:

A child is trying to throw a ball over a fence. She gives the ball an initial speed of 8.0 m/s at an angle of 40° above the horizontal. The ball leaves her hand 1.0 m above the ground and the fence is 2.0 m high. The ball just clears the fence while still traveling upwards and experiences no significant air resistance. How far is the child from the fence?

Answers

Answer:

the child is 1.581 m far from the fence

Explanation:

The diagrammatic illustration that give a better view of what the question denote can be seen in the image attached below.

From the image attached below, let assume that the release point is the origin, then equation of the motion (x) is as follows:

[tex]x - x_o = u_xt[/tex]

[tex]\mathtt{x = u_xt \ \ \ since (x_o = 0)}[/tex]  ---- (1)

the equation of the motion y is :

[tex]\mathtt{y - y_o =u_yt - 0.5 gt^2}[/tex]

[tex]\mathtt{y = u_yt-4.9t^2 \ \ \ since (y_o =0)}[/tex]

[tex]\mathtt{ 1= (u \ sin 40^0)t -4.9 \ t^2 }[/tex]

[tex]\mathtt{1 = 8 sin 40^0 t - 4.9 t^2}[/tex]

[tex]\mathtt{1 = 5.14t - 4.9t^2}[/tex]

[tex]\mathtt{4.9t^2 - 5.14t +1 = 0}[/tex]

By using the quadratic formula, we have;

[tex]\mathtt{ \dfrac{ -b \pm \sqrt{b^2 - 4ac}}{2a}} }[/tex]

where;

a = 4.9,   b = -5.14     c = 1

[tex]= \mathtt{ \dfrac{ -(-5.14) \pm \sqrt{(-5.14)^2 - 4(4.9)(1)}}{2(4.9)}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14 \pm \sqrt{26.4196 -19.6}}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14 \pm \sqrt{6.8196}}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14+ \sqrt{6.8196}}{9.8} \ \ OR \ \ \dfrac{ 5.14- \sqrt{6.8196}}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14+ 2.6114}{9.8} \ \ OR \ \ \dfrac{ 5.14- 2.6114}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 7.7514}{9.8} \ \ OR \ \ \dfrac{ 2.5286}{9.8}} }[/tex]

[tex]= \mathbf{ 0.791 \ \ OR \ \ 0.258} }[/tex]

In as much as the ball is traveling upward, then we consider t= 0.258sec.

From equation (1)

[tex]\mathtt{x = u_x(0.258)}[/tex]

[tex]\mathtt{x = ucos 40^0 (0.258)}[/tex]

[tex]\mathtt{x = 8 \ cos 40^0 (0.258)}[/tex]

[tex]\mathbf{x = 1.581 \ m}[/tex]

Thus, the child is 1.581 m far from the fence

A series LR circuit contains an emf source of 19 V having no internal resistance, a resistor, a 22 H inductor having no appreciable resistance, and a switch. If the emf across the inductor is 80% of its maximum value 4 s after the switch is closed, what is the resistance of the resistor

Answers

Answer: R = 394.36ohm

Explanation: In a LR circuit, voltage for a resistor in function of time is given by:

[tex]V(t) = \epsilon. e^{-t.\frac{L}{R} }[/tex]

ε is emf

L is indutance of inductor

R is resistance of resistor

After 4s, emf = 0.8*19, so:

[tex]0.8*19 = 19. e^{-4.\frac{22}{R} }[/tex]

[tex]0.8 = e^{-\frac{88}{R} }[/tex]

[tex]ln(0.8) = ln(e^{-\frac{88}{R} })[/tex]

[tex]ln(0.8) = -\frac{88}{R}[/tex]

[tex]R = -\frac{88}{ln(0.8)}[/tex]

R = 394.36

In this LR circuit, the resistance of the resistor is 394.36ohms.

An LR circuit consists of a 35-mH inductor, a resistance of 12 ohms, an 18-V battery, and a switch. What is the current 5.0 ms after the switch is closed

Answers

Answer:

Current, I = 1.23 A

Explanation:

Given that,

Inductance, L = 35 mH

Resistance, R = 12 ohms

Potential difference, V = 18 V

We need to find current 5 ms after the switch is closed. Current in LR circuit is given by :

[tex]I=I_o(1-e^{-t/\tau })[/tex] ....(1)

Here,

[tex]I_o[/tex] is final current

[tex]I_o=\dfrac{V}{R}\\\\I_o=\dfrac{18}{12}=1.5\ A[/tex]

[tex]\tau[/tex] is time constant

[tex]\tau=\dfrac{L}{R}\\\\\tau=\dfrac{35\times 10^{-3}}{12}\\\\\tau=0.00291\ s[/tex]

So, equation (1) becomes :

[tex]I=1.5\times (1-e^{-5\times 10^{-3}/0.00291})\\\\I=1.23\ A[/tex]

So, after 5 ms the current in the circuit is 1.23 A.

What happens to the magnetic field when you reverse the direction of current by sliding the battery voltage bar past 0 volts

Answers

Answer:

The polarity of the magnetic field changes

Explanation:

This because The magnetic field generated is always perpendicular to the direction of the current and parallel to the solonoid. Hence if we reverse the current the direction of magnetism also reverses. In other words the magnetic poles gets reversed (North pole becomes south pole and the south pole becomes the north pole)

A competitive diver leaves the diving board and falls toward the water with her body straight and rotating slowly. She pulls her arms and legs into a tight tuck position. What happens to her rotational kinetic energy

Answers

Answer: her rotational kinetic energy increases

What is the minimum thickness of coating which should be placed on a lens in order to minimize reflection of 566 nm light? The index of refraction of the coating material is 1.46 and the index of the glass is 1.71.

Answers

Answer:

The  thickness is   [tex]t = 1.415 *10^{-7 } \ m[/tex]

Explanation:

From the question we are told that

    The wavelength is  [tex]\lambda = 566 \ nm = 566 *10^{-9} \ m[/tex]

     The  index of refraction of glass is  [tex]n_g = 1.71[/tex]

     The index of refraction of the coating is  [tex]n= 1.46[/tex]

Generally the condition for destructive interference is  

         [tex]2 t = (m + \frac{1}{2} ) * \frac{\lambda }{n }[/tex]

Here m is the order of the interference pattern and given from the question that we are considering minimizing  reflection  m = 0

t = thickness of the coating

substituting values

         [tex]2 t = (0 + \frac{1}{2} ) * \frac{ 566 *10^{-9}}{ 1.46 }[/tex]

    =>    [tex]t = 1.415 *10^{-7 } \ m[/tex]

           

Kinetic and
A brick is resting on a smooth wooden board that is at a 30° angle. What is one way to overcome the static friction that is holding the brick in place?
11 point)
O raise the board to a higher angle
O press down on the brick in a direction that is perpendicular to the board
O roughen up the texture of the wooden board
o lower the board so it's level with the ground

Answers

Answer:

raise the board to a higher angle

Explanation:

Static friction is the force opposite to the applied force.

Static friction is dependent on the angle of inclination, it means as the angle of incline increases, the force of friction will increases as normal force will decrease.

So, if the board will be raised to a higher angle, it will increase the angle of incline and will overcome the static friction and block will be able slide.

Hence, the correct option is "raise the board to a higher angle".

A person can see clearly up close but cannot focus on objects beyond 75.0 cm. She opts for contact lenses to correct her vision.
(a) Is she nearsighted or farsighted?
(b) What type of lens (converging or diverging) is needed to correct her vision?
(c) What focal length contact lens is needed, and what is its power in diopters?

Answers

Answer:

(a) nearsighted

(b) diverging

(c) the lens strength in diopters is 1.33 D, and considering the convention for divergent lenses normally prescribed as: -1 33 D

Explanation:

(a) The person is nearsighted because he/she cannot see objects at distances larger than 75 cm.

(b) the type of correcting lens has to be such that it counteracts the excessive converging power of the eye of the person, so the lens has to be diverging (which by the way carries by convention a negative focal length)

(c) the absolute value of the focal length (f) is given by the formula:

[tex]f=\frac{1}{d} =\frac{1}{0.75} = 1.33\,D[/tex]

So it would normally be written with a negative signs in front indicating a divergent lens.

If one could transport a simple pendulum of constant length from the Earth's surface to the Moon's, where acceleration due to gravity is one-sixth (1/6) that on the Earth, by what factor would be the pendulum frequency be changed

Answers

Answer:

The frequency will change by a factor of 0.4

Explanation:

T = 2(pi)*sqrt(L/g)

Since g(moon) = (1/6)g(earth), the period would change by sqrt[1/(1/6)] = sqrt(6) ~ 2.5 times longer on the moon. Since the period & frequency are inverses, the frequency would be 1/2.5 or 0.4 times shorter on the moon.

Suppose you exert a force of 185 N tangential to the outer edge of a 1.73-m radius 76-kg grindstone (which is a solid disk).

Required:
a. What torque is exerted?
b. What is the angular acceleration assuming negligible opposing friction?
c. What is the angular acceleration if there is an opposing frictional force of 20.0 N exerted 1.50 cm from the axis?

Answers

Answer:

a. 320.06 Nm b. 2.814 rad/s² c. 2.811 rad/s².

Explanation:

a. The torque exerted τ = Frsinθ where F = tangential force exerted = 185 N, r = radius of grindstone = 1.73 m and θ = 90° since the force is tangential to the grindstone.

τ = Frsinθ

= 185 N × 1.73 m × sin90°

= 320.05 Nm

So, the torque τ = 320.05 Nm

b. Since torque τ = Iα where I = moment of inertia of grindstone = 1/2MR² where M = mass of grindstone = 76 kg and R = radius of grindstone = 1.73 m

α = angular acceleration of grindstone

τ = Iα

α = τ/I = τ/(MR²/2) = 2τ/MR²

substituting the values of the variables, we have

α = 2τ/MR²

= 2 × 320.05 Nm/[76 kg × (1.73 m)²]

= 640.1 Nm/227.4604 kgm²

= 2.814 rad/s²

So, the angular acceleration α = 2.814 rad/s²

c. The opposing frictional force produces a torque τ' = F'r' where F' = frictional force = 20.0 N and r' = distance of frictional force from axis = 1.50 cm = 0.015 m.

So  τ' = F'r' = 20.0 N × 0.015 m = 0.3 Nm

The net torque on the grindstone is thus τ'' = τ - τ' = 320.05 Nm - 0.3 Nm = 319.75 Nm

Since τ'' = Iα

α' = τ''/I where α' = its new angular acceleration

α' = 2τ/MR²

= 2 × 319.75 Nm/[76 kg × (1.73 m)²]

= 639.5 Nm/227.4604 kgm²

= 2.811 rad/s²

So, the angular acceleration α' = 2.811 rad/s²

A deep-space vehicle moves away from the Earth with a speed of 0.870c. An astronaut on the vehicle measures a time interval of 3.10 s to rotate her body through 1.00 rev as she floats in the vehicle. What time interval is required for this rotation according to an observer on the Earth

Answers

Answer:

t₀ = 1.55 s

Explanation:

According to Einstein's Theory of Relativity, when an object moves with a speed comparable to speed of light, the time interval measured for the event, by an observer in  motion relative to the event is not the same as measured by an observer at rest.

It is given as:

t = t₀/[√(1 - v²/c²)]

where,

t = time measured by astronaut in motion = 3.1 s

t₀ = time required according to observer on earth = ?

v = relative velocity = 0.87 c

c = speed of light

3.1 s = t₀/[√(1 - 0.87²c²/c²)]

(3.1 s)(0.5) = t₀

t₀ = 1.55 s

Answer:

The time interval required for this rotation according to an observer on the Earth = [tex]6.29sec[/tex]

Explanation:

Time interval required for this rotation according to an observer on the Earth is given as [tex]\delta t[/tex]

where,

[tex]t_o = 3.1\\\\v = 0.87[/tex]

[tex]\delta t = \frac{t_o}{\sqrt{1-\frac{v^2}{c^2}}}\\\\\delta t = \frac{3.1}{\sqrt{1-(\frac{0.87c}{c})^2}}\\\\\delta t = 6.29sec[/tex]

For more information visit

A 26-g rifle bullet traveling 220 m/s embeds itself in a 3.8-kg pendulum hanging on a 2.7-m-long string, which makes the pendulum swing upward in an arc, Determine the vertical and horizontal component of the pendulum's maximum displacement

Answers

Answer:

displacements are 0.776m, 0.114m

Explanation:

We were given mass of 26-g rifle bullet , then we can convert to Kg since

Momentum is conserved here.

The initial momentum before impact = (Mi * Vi)

Where Mi= initial given mass

Vi=initial velocity given

= 0.026 * 220 = 5.72 kgm/s

The final momentum after impact is (Mf * Vf )

Mf= final mass

5.72=( 3.82* Vf )

= 5.72/ 3.82

= 1.497 m/s

the speed of the pendulum bob with bullet afterwards= 1.497 m/s

the total energy after the collision is the addition of the kinetic energy of the bob+bullet and the potential energy of the bob and bullet, potential energy can be taken as zero.

M = 3.82 kg the mass of the bob containing the bullet

E(total) = ¹/₂MV² = 1/2 * (3.82kg)*(1.497m/s)² = 4.280J

When the Bob got to highest point the kinetic energy is zero and the potential energy is due to the increase in height of the bob, and the addition of the potential and kinetic energies still equal the total energy from before

E(total) = Mgh + 0 = Mgh = 4.280J

solving for h and substituting,

h = 4.280 J/(9.8m/s^2*3.82kg) = 0.114 m

Since the height is found,we the angle of the pendulum at the top of the swing can also be determined

A = arccos[(2.7 - 0.114) / 2.7] or A = 16.71degrees

Since A is known, the displacement along the horizontal axis can be calculated as

x = 2.7* sin(A) = 0.776m

therefore, displacement is 0.776m, 0.114m

the vertical and horizontal component of the pendulum's maximum displacement are displacement is 0.776m, 0.114m

Adjust the mass of the refrigerator by stacking different objects on top of it. If the mass of the refrigerator is increased (with the Applied Force held constant), what happens to the acceleration

Answers

Answer:

The acceleration of the refrigerator together with the objects decreases.

Explanation:

If the mass of the refrigerator is increased by stacking more masses (objects) on it,

and the force applied remains constant, then we know from

F = ma

where

F is the applied force

m is the total mass of the refrigerator and the objects

a is the acceleration of the masses.

If F is constant, and m is increased, the acceleration will decrease

Answer:

The acceleration decreases.

Explanation:

its right

A viewing screen is separated from a double slit by 5.20 m. The distance between the two slits is 0.0300 mm. Monochromatic light is directed toward the double slit and forms an interference pattern on the screen. The first dark fringe is 3.70 cm from the center line on the screen.

Required:
a. Determine the wavelength of light.
b. Calculate the distance between the adjacent bright fringes.

Answers

Answer:

The wavelength of this light is approximately [tex]427\; \rm nm[/tex] ([tex]4.27\times 10^{-7}\; \rm m[/tex].)The distance between the first and central maxima is approximately [tex]7.40\; \rm cm[/tex] (about twice the distance between the first dark fringe and the central maximum.)  

Explanation:

Wavelength

Convert all lengths to meters:

Separation of the two slits: [tex]0.0300\; \rm mm = 3.00\times 10^{-5}\; \rm m[/tex].Distance between the first dark fringe and the center of the screen: [tex]3.70\; \rm cm = 3.70\times 10^{-2}\; \rm m[/tex].

Refer to the diagram attached (not to scale.) Assuming that the screen is parallel to the line joining the two slits. The following two angles are alternate interior angles and should be equal to each other:

The angle between the filter and the beam of light from the lower slit, andThe angle between the screen and that same beam of light.

These two angles are marked with two grey sectors on the attached diagram. Let the value of these two angles be [tex]\theta[/tex].

The path difference between the two beams is approximately equal to the length of the segment highlighted in green. In order to produce the first dark fringe from the center of the screen (the first minimum,) the length of that segment should be [tex]\lambda / 2[/tex] (one-half the wavelength of the light.)

Therefore:

[tex]\displaystyle \cos \theta \approx \frac{\text{Path difference}}{\text{Slit separation}} = \frac{\lambda / 2}{3.00\times 10^{-5}\; \rm m}[/tex].

On the other hand:

[tex]\begin{aligned} \cot \theta &\approx \frac{\text{Distance between central peak and first minimum}}{\text{Distance between the screen and the slits}} \\ &= \frac{3.70\times 10^{-2}\; \rm m}{5.20\; \rm m} \approx 0.00711538\end{aligned}[/tex].

Because the cotangent of [tex]\theta[/tex] is very close to zero,

[tex]\cos \theta \approx \cot \theta \approx 0.00711538[/tex].

[tex]\displaystyle \frac{\lambda /2}{3.00\times 10^{-5}\; \rm m} \approx \cos\theta\approx 0.00711538[/tex].

[tex]\begin{aligned}\lambda &\approx 2\times 0.00711538 \times \left(3.00\times 10^{-5}\; \rm m\right) \\ &\approx 4.26 \times 10^{-7}\; \rm m = 426\; \rm nm\end{aligned}[/tex].

Distance between two adjacent maxima

If the path difference is increased by one wavelength, then the intersection of the two beams would move from one bright fringe to the next one.

The path difference required for the central maximum is [tex]0[/tex].The path difference required for the first maximum is [tex]\lambda[/tex].The path difference required for the second maximum is [tex]2\,\lambda[/tex].

On the other hand, if the distance between the maximum and the center of the screen is much smaller than the distance between the screen and the filter, then:

[tex]\begin{aligned}&\frac{\text{Distance between image and center of screen}}{\text{Distance between the screen and the slits}} \\ &\approx \cot \theta \\ &\approx \cos \theta \\ &\approx \frac{\text{Path difference}}{\text{Slit separation}}\end{aligned}[/tex].

Under that assumption, the distance between the maximum and the center of the screen is approximately proportional to the path difference. The distance between the image (the first minimum) and the center of the screen is [tex]3.70\; \rm cm[/tex] when the path difference is [tex]\lambda / 2[/tex]. The path difference required for the first maximum is twice as much as that. Therefore, the distance between the first maximum and the center of the screen would be twice the difference between the first minimum and the center of the screen: [tex]2 \times 3.70\; \rm cm = 7.40\; \rm cm[/tex].

A nearsighted person has a far point that is 4.2 m from his eyes. What focal length lenses in diopters he must use in his contacts to allow him to focus on distant objects?

Answers

Answer:

-0.24diopters

Explanation:

The lens is intended that makes an object at infinity appear to be 4.2 m away, so do=infinity, dI = - 4.2m (minus sign because image is on same side of lens as object)

So 1/do +1/di = 1/f

1/infinity + 1/-4.2 = 1/f

1/f = 1/-4.2 = -0.24diopters

A long bar slides on two contact points and is in motion with velocity ν. A steady, uniform, magnetic field B is present. The induced current through resistor R is:

Answers

Answer:

The induced current in the resistor is I = BLv/R

Explanation:

The induced emf ε in the long bar of length, L in a magnetic field of strength, B moving with a velocity, v is given by

ε = BLv.

Now, the current I in the resistor is given by

I = ε/R where ε = induced emf in circuit and R = resistance of resistor.

So, the current I = ε/R.

substituting the value of ε the induced emf, we have

I = ε/R

I = BLv/R

So, the induced current through the resistor is given by I = BLv/R

10. How far does a transverse pulse travel in 1.23 ms on a string with a density of 5.47 × 10−3 kg/m under tension of 47.8 ????? How far will this pulse travel in the same time if the tension is doubled?

Answers

Answer: Tension = 47.8N, Δx = 11.5×[tex]10^{-6}[/tex] m.

              Tension = 95.6N, Δx = 15.4×[tex]10^{-5}[/tex] m

Explanation: A speed of wave on a string under a tension force can be calculated as:

[tex]|v| = \sqrt{\frac{F_{T}}{\mu} }[/tex]

[tex]F_{T}[/tex] is tension force (N)

μ is linear density (kg/m)

Determining velocity:

[tex]|v| = \sqrt{\frac{47.8}{5.47.10^{-3}} }[/tex]

[tex]|v| = \sqrt{0.00874 }[/tex]

[tex]|v| =[/tex] 0.0935 m/s

The displacement a pulse traveled in 1.23ms:

[tex]\Delta x = |v|.t[/tex]

[tex]\Delta x = 9.35.10^{-2}*1.23.10^{-3}[/tex]

Δx = 11.5×[tex]10^{-6}[/tex]

With tension of 47.8N, a pulse will travel Δx = 11.5×[tex]10^{-6}[/tex]  m.

Doubling Tension:

[tex]|v| = \sqrt{\frac{2*47.8}{5.47.10^{-3}} }[/tex]

[tex]|v| = \sqrt{2.0.00874 }[/tex]

[tex]|v| = \sqrt{0.01568}[/tex]

|v| = 0.1252 m/s

Displacement for same time:

[tex]\Delta x = |v|.t[/tex]

[tex]\Delta x = 12.52.10^{-2}*1.23.10^{-3}[/tex]

[tex]\Delta x =[/tex] 15.4×[tex]10^{-5}[/tex]

With doubled tension, it travels [tex]\Delta x =[/tex] 15.4×[tex]10^{-5}[/tex] m

Other Questions
A body is thrown vertically upwards with a speed of 95m / s and after 7s it reaches its maximum height. How fast does it reach its maximum height? What was the maximum height reached? What is one way that Henrys speech uses gurative language Calculate the molar solubility of CaF2 at 25C in a solution that is 0.010 M in Ca(NO3)2. The Ksp for CaF2 is 3.9 x 10-11. According to the producer price index database maintained by the Bureau of Labor Statistics, the average cost of computer equipment fell 3.8 percent between January and December 2016. Let's see whether these changes are reflected in the income statement of Computer Tycoon Inc. for the year ended December 31, 2016. 2016 2015 Sales Revenue $ 109,000 $ 133,500Cost of Goods Sold 64,500 75,100Gross Profit 44,500 58,400Selling, General, and Administrative Expenses 36,900 38,800Interest Expense 590 520Income before Income Tax Expense 7,010 19,080Income Tax Expense 1,500 5,900 Net Income $ 5,510 $ 13,180 Required: 1. Compute the times interest earned ratios for 2016 and 2015. (Round your answers to 1 decimal place.) Times Interest Earned 2015 2016 2. Does Computer Tycoon generate sufficient net income in both years before taxes and interest) to cover the cost of debt financing? a. Yes b. No importance of financial security to the individuals? Find the measure of f. What is the total surface area of the square pyramid below? A square pyramid. The square base has side lengths of 10 centimeters. The triangular sides have a height of 14 centimeters. 100 cm2 200 cm2 280 cm2 380 cm2 A line runs tangent to a circle at the point (4, 2). The line runs through the origin. Find the slope of the tangent line. Lilly smiles at, makes direct eye contact with, and touches her romantic partner, Dolores, frequently and Dolores does the same for Lilly. Their nonverbal behavior is mostly likely communicating _____. For the given data value, find the standard score and the percentile. A data value 0.6 standard deviations above the mean. A Missouri job shop has four departments machining (M), dipping in a chemical bath (D), finishing (F), and plating (P) assigned to four work areas. The operations manager, Mary Marrs, has gathered the following data for the movement of material. The number of workpieces moved yearly between work areas are: M D F P M - 800 2,000 200 D - - 400 400 F - - - 2,000 P - - - -It costs $0.75 to move 1 workpiece 1 foot in the job shop. For the layout design of the job shop, LAYOUT PLAN A: Distance between work areas (departments) in feet: M D F PM - 21 12 8D - - 5 10F - - - 4P - - - -The yearly total material handling cost of the current layout presented in PLAN A_____________. The following equation is an example ofdecay.18118579Au 42He+ Find the solution of the system of equations.2x 10y = -28-10x + 10y = -20GbA Cost recovery. Richardses' Tree Farm, Inc. purchased a new aerial tree trimmer for $. It is classified in the property class category of a single-purpose agricultural and horticultural structure. Then the company sold the tree trimmer after four years of service. If a seven-year life and MACRS, LOADING..., was used for the depreciation schedule, what is the after-tax cash flow from the sale of the trimmer (use a % tax rate) if a. the sales price was $? b. the sales price was $? c. the sales price was $? a. If the sales price is $, what is the after-tax cash flow? The city plans a roadway to have trees every mile. If the path is miles long, how many trees will the city need?30 trees31 trees32 trees33 trees Help, Answer ASAP; will give brainliest Part This table shows the prices of the three TVs in addition to their length and width. Is the price of a TV proportional to the length of its screen? Howdo you know 12. 12 ounces is roughly the same asO A. 340 grams.B. 356 grams.O C. 400 grams.O D. 120 grams.Mark for review (Will be highlighted on the movin A landlord rented an apartment to a person with a wheelchair. The landlord allowed the tenant to install bath rails and replace the bathroom sink vanity with a pedestal sink with lever faucet handles; however, the landlord required the tenant to sign a restoration agreement that the accommodations would be restored to their former condition at the end of the lease. In addition, the landlord required the tenant to pay sufficient funds (over a period of time) into an escrow account to cover the bathroom restoration. Has the landlord violated the Fair Housing Act 1. What is the difference between an exponential growth and exponential decay? 2. What is an example equation for expoential growth and an example equation for exponential decay?