Answer:
104.8 g
Explanation:
From the question given above, the following data were obtained:
Initial temperature of copper (T꜀) = 275.1 °C
Mass of water (Mᵥᵥ) = 272 g
Initial temperature of water (Tᵥᵥ) = 21 °C
Equilibrium temperature (Tₑ) = 29.7 °C
Mass of copper (M꜀) =?
NOTE:
Specific heat capacity of copper (C꜀) = 0.385 J/gºC
Specific heat capacity of water (Cᵥᵥ) = 4.184 J/gºC
Finally, we shall determine the mass of the copper in the sample. This can be obtained as follow:
Heat loss by copper = Heat gained by water
M꜀C꜀(T꜀ – Tₑ) = MᵥᵥCᵥᵥ(Tₑ – Tᵥᵥ)
M꜀ × 0.385 (275.1 – 29.7) = 272 × 4.184(29.7 – 21)
M꜀ × 0.385 × 245.4 = 1138.048 × 8.7
M꜀ × 94.479 = 9901.0176
Divide both side by 94.479
M꜀ = 9901.0176 / 94.479
M꜀ = 104.8 g
Thus, the mass of the copper in the sample is 104.8 g
HELP ASAS 15 POINTS
When using the process of evaporation to separate a mixture, what is left behind in the evaporating dish?
A. None of these.
B. The liquid evaporates and the solid is left in the dish.
C. The mixture does not separate, and the entire mixture evaporates.
D. The mixture does not separate, and the entire mixture remains in the dish.
Answer:
liquid will be evaporated while solid remains
Consider the reaction between CaCO3 and HCl. Which of the following could speed up the reaction?
I. Increasing concentration of the HCl
II. Increasing size of the CaCO3 pieces
III. Increasing temperature
a) I and III only
b) I, II, and III
c) I only
d) II and III only
Which option is a physical property of matter?
A. acidity
B. reactivity
C. boiling point
D. flammability
Answer:
boiling point is the physial property of matter
The option that is showing the physical property of the matter is boiling point, the correct option is C.
What is physical property?A physical property is any measurable property whose value describes the state of a physical system.
Changes in a system's physical properties can be used to describe its transitions between momentary states. Physical properties are also known as observables. They do not have modal properties.
Physical properties include color, phase, odor, and boiling point. Since reactivity with oxygen is dependent on the chemical nature of the object, it is not a physical property.
A compound's physical property is one that can be observed and measured. The chemical composition of a compound is unaffected by a physical property.
Thus, the correct option is C.
For more details regarding physical property, visit:
https://brainly.com/question/18327661
#SPJ6
How many oxygen atoms are there in 0.25 mole of CO2?
Answer:
It is known that 1 mol of a molecule contains 6.023×1023 6.023 × 10 23 number of molecules. So, 0.25 moles of CO2 C O 2.
The correct option for the given question about Mole Concept is Na / 2 atom of oxygen.
What is mole?In chemistry, a mole is a unit. A mole of a substance is the mass of the substance containing precisely 12 gram of the same number of atoms as 12C.The mole is the SI unit used to measure a substance's quantity. It has the symbol mol.
How to solve this question?
In 1 mole number of molecules of CO₂ = Na (Avagadro Number)
In 0.25 mole number of molecules of CO₂ = 0.25 × Na molecules
In 1 molecule number of oxygen atom = 2 atom
In 0.25 × Na molecules number of oxygen atom = 2 × 0.25 × Na atom
In 0.25 × Na molecules number of oxygen atom = 0.5 × Na atom
So in 0.25 mole of CO₂ number of oxygen atom = Na / 2 atom
Thus we can conclude that in 0.25 mole of CO₂ number of oxygen atom will be Na / 2, where Na is Avagadro Number.
Learn more about Mole Concept here:
https://brainly.com/question/16488605
#SPJ2
tom pays 5 cents per minute to use his cell phone. Write an expression for the cost in cents of using his cell phone for minutes.
Answer:5m
Explanation:Because in the question it say per minute so it would be 5 times m
At 445oC, Kc for the following reaction is 0.020. 2 HI(g) <--> H2 (g) + I2 (g) A mixture of H2, I2, and HI in a vessel at 445oC has the following concentrations: [HI] = 1.5 M, [H2] = 2.50 M and [I2] = 0.05 M. Which one of the following statements concerning the reaction quotient, Qc, is TRUE for the above system?
a. Qc = Kc; the system is at equilibrium.
b. Qc is less than Kc; more H2 and I2 will be produced.
c. Qc is less than Kc; more HI will be produced.
d. Qc is greater than Kc; more HI will be produced.
Explanation:
The given balanced chemical equation is:
[tex]2 HI(g) <--> H_2 (g) + I_2 (g)[/tex]
The value of Kc at 445oC is 0.020.
[HI]=1.5M
[H2]=2.50M
[I2]=0.05M
The value of Qc(reaction quotient ) is calculated as shown below:
Qc has the same expression as the equilibrium constant.
[tex]Qc=\frac{[H_2][I_2]}{[HI]^2} \\Qc=(2.50Mx0.05M)/(1.5M)^2\\Qc=0.055[/tex]
Qc>Kc,
Hence, the backward reaction is favored and the formation of Hi is favored.
Among the given options, the correct answer is option d. Qc is greater than Kc; more HI will be produced.
chemistry
Which of the following is a characteristic of solid silver?
O A. High electrical conductivity
O B. Brittleness
C. Low melting point
O D. Good insulator
SUBM
Answer:
A. High electrical conductivity
Explanation:
solid silver isn't brittle, it has a high melting point, and its not a good insulator.
I NEED A ANSWER FOR THIS QUESTION, ASAP
4. A sample of ammonia, NH3, contains 3.3 x 1021 hydrogen atoms. How many NH; molecules are in this sample?
Answer:
1.1 × 10²¹ NH₃ molecules
Explanation:
From the given information:
We were being told that the number of the hydrogen (H) atoms present in the sample of NH3 = 3.3 × 10²¹ hydrogen.
However, it signifies that each molecule of ammonia harbors 3hydrogen (H) atoms.
Hence, the number of molecules of NH₃ present;
[tex]\mathsf{=\dfrac{3.3\times 10^{21}}{3} \ molecules \ of \ {NH_3}}[/tex]
= 1.1 × 10²¹ NH₃ molecules
Which are the following exothermic or endothermic
Absorbs Energy
-Hrxn
+Hrxn
Feels Hot
Heat flows from surrounds to Reaction
Not Energetically Favorable
Energetically Favorable
Releases Energy
Feels Cold
Heat flows from the reaction to the surrounds
Answer:
Explanation:
Your mom
Oxygen and hydrogen are compressed into two cubical boxes of the same
size at a temperature of 28 K. What do these gases have in common
according to the kinetic theory?
Explanation:
Following are the kinetic theory of gases postulates:
1) Space-volume to molecules ratio is negligible.
2)There is no force of attraction between the molecules at normal temperature and pressure. The force of attraction between the molecules build when the temperature decreases and the pressure increases.
3) There is large space between the molecules resulting in continuous motion.
4) The free movement of molecules results in collision which is perfectly elastic.
5) The molecules have kinetic energy due to random movement. But the average kinetic energy of these molecules differs with temperature.
6) Molecules exert pressure on the walls of the container.
what characterizes a homogeneous mixture?
Answer:
a mixture that doesn't really show the ingredients or things put into the material or food.
1. Explain the test for unsaturation.
2. Write down the balanced chemical equations for the complete and incomplete
combustion of octene
3. Explain how propanol, an alcohol, is formed from propene..
4. How is margarine formed?
Answer:
1)In organic chemistry, the bromine test is a qualitative test for the presence of unsaturation (carbon-to-carbon double or triple bonds), phenols and anilines. ... The more unsaturated an unknown is, the more bromine it reacts with, and the less coloured the solution will appear.
2)The equation for incomplete combustion of propane is: 2 C3H8 + 9 O2 → 4 CO2 + 2 CO + 8 H2O + Heat. If not enough oxygen is present for complete combustion, incomplete combustion occurs. The result of incomplete combustion is, once again, water vapour, carbon dioxide and heat. But it also produces carbon monoxide.
Explanation:
3)Propene, also known as propylene, is an unsaturated organic compound with the chemical formula {\displaystyle {\ce {CH3CH=CH2}}}. It has one double bond, and is the second simplest member of the alkene class of hydrocarbons. It is a colorless gas with a faint petroleum-like odor.
Formula: C3H6
IUPAC ID: Propene
4)Margarines are chemically created during hydrogenation which, until January 1, 2006, relied upon trans fats to solidify their vegetable oils. Food companies have been exploring options for replacing trans fat in partially hydrogenated margarine.
According to the ideal gas law, a 9.998 mol sample of argon gas in a 0.8311 L container at 502.7 K should exert a pressure of 496.2
atm. What is the percent difference between the pressure calculated using the van der Waals' equation and the ideal pressure? For Ar
gas, a = 1.345 L’atm/mol? and b = 3.219x10-2 L/mol.
Pideal – Puan der Waals |
Percent difference
x 100
Answer:
[tex]\%diff=24.0\%[/tex]
Explanation:
Hello there!
In this case, according to the given information, it turns out firstly necessary for us to set up the van der Waals' equation as shown below:
[tex]p=\frac{RT}{v-b}-\frac{a}{v^2}[/tex]
Thus, we secondly calculate the molar volume as:
[tex]v=\frac{0.8311L}{9.998mol} =0.083L/mol[/tex]
Then, we plug in the entire variables in the vdW equation to get such pressure:
[tex]p=\frac{0.08206\frac{atm*L}{mol*K}*502.7K}{0.08313L/mol-0.03219L/mol}-\frac{1.345L*atm/mol}{(0.08313L/mol)^2}\\\\p=615.2atm[/tex]
And the ideal gas pressure:
[tex]p=\frac{0.08206\frac{atm*L}{mol*K}*502.7K}{0.08313L/mol}\\\\p=496.2atm[/tex]
Finally, the percent difference:
[tex]\%diff=\frac{|496.2atm-615.2atm|}{496.2atm} *100\%\\\\\%diff=24.0\%[/tex]
Regards!
what is the difference between red phosphorus and white phosphorus?
Answer:
White phosphorusRed PhosphorusIt is insoluble in water but soluble in carbon disulphide.It is insoluble in both water and carbon disulphide.It undergoes spontaneous combustion in air.It is relatively
Explanation:
I hope it will help you
In a quantitative analysis, a methanol (CH3OH) contaminated water sample was titrated with 0.0021 mol L- potassium permanganate (KMnO4). 50.00 mL samples of the water to be tested were acidified by sulfuric acid, then titrated with the permanganate solution. The results are shown below. Burette reading, ml 1st titration 2nd titration 3rd titration 4th titration Final volume 12.40 19.60 26.60 17.25 Initial volume 4.45 12.50 19.60 10.15 Titre 7.95 7.10 7.00 7.10 The complete equation for the redox titration reaction is: 4MnO4- + 12H+ + 5CH3OH → 4Mn2+ + 11H2O + 5HCOOH a. [5] Calculate the concentration of the methanol in mol L-1.
In a REDOX titration, one specie is oxidized while the other is reduced. The concentration of methanol is 0.012 mol L-1. Methanol is the oxidizing agent while permanganate is the reducing agent.
The average titre value is; [tex]\frac{7.95 + 7.10 + 7.00 + 7.10}{4}[/tex] = 7.29 mL
Equation of the reaction is:
[tex]4MnO4- + 12H+ + 5CH3OH ----> 4Mn2+ + 11H2O + 5HCOOH[/tex]
Concentration of oxidizing agent = CA = ?
Concentration of reducing agent = CB = 0.0021 mol L-1
Volume of oxidizing agent = VA= 7.29 mL
Volume of reducing agent = VB = 50.00 mL
Number of moles of oxidizing agent NA = 4
Number of moles of reducing agent NB = 5
Note that NA and NB are obtained from the balanced reaction equation
CAVA/CBVB = NA/NB
CAVANB = CBVBNA
CA = CBVBNA/VANB
CA = 0.0021 mol L-1 * 50.00 mL * 4/7.29 mL * 5
CA= 0.012 mol L-1
For a comprehensive definition of redox titration see
https://brainly.com/question/24018439
Urea, CH4N2O (s), is manufactured from NH3 (g) and CO2 (g). H2O (l) is another product of this reaction. An experiment is started with 2.6 grams of NH3 (g) added into a reaction vessel with CO2 (g).
Write the balanced equation for this reaction, being sure to include physical states. Based on the balanced equation above, calculate the following:
a. the theoretical yield of urea in grams that can be made from the NH3
b. the actual amount of urea made if the percent yield for this reaction is 34%.
Answer:
a. 4.41 g of Urea
b. 1.5 g of Urea
Explanation:
To start the problem, we define the reaction:
2NH₃ (g) + CO₂ (g) → CH₄N₂O (s) + H₂O(l)
We only have mass of ammonia, so we assume the carbon dioxide is in excess and ammonia is the limiting reactant:
2.6 g . 1mol / 17g = 0.153 moles of ammonia
Ratio is 2:1. 2 moles of ammonia can produce 1 mol of urea
0.153 moles ammonia may produce, the half of moles
0153 /2 = 0.076 moles of urea
To state the theoretical yield we convert moles to mass:
0.076 mol . 58 g/mol = 4.41 g
That's the 100 % yield reaction
If the percent yield, was 34%:
4.41 g . 0.34 = 1.50 g of urea were produced.
Formula is (Yield produced / Theoretical yield) . 100 → Percent yield
For which of the following reactions is the enthalpy change equal to the second ionization energy of nitrogen?
Answer:
"[tex]N^+(g) \rightarrow N^{2+}(g) + e^-[/tex]" is the appropriate answer.
Explanation:
Whenever one electron or particle must be removed from some kind of gas atom or molecule, it requires that the very first amount of energy necessary.Two electrons must be removed from such a mono-positive exhaust gases structure or position of ion before they may become a dipositive gaseous ion.Thus the above is the correct answer.
Isotopes are: A. are only theoretical. B. only formed in laboratories. C. found in nature. D. found in the nuclear reactions in stars but not on Earth.
Answer:
B. only formed in laboratories
Explanation:
i know
Isotopes are only formed in Laboratories. hence, Option (B) is correct.
What are Isotopes ?
Each of two or more forms of the same element that contain equal numbers of protons but different numbers of neutrons in their nuclei, and hence differ in relative atomic mass but not in chemical properties; in particular, a radioactive form of an element is known as Isotope.
Isotopes are two or more types of atoms that have the same atomic number and position in the periodic table, and that differ in nucleon numbers due to different numbers of neutrons in their nuclei.
Therefore, Isotopes are only formed in Laboratories. hence, Option (B) is correct.
Learn more about Isotopes here ;
https://brainly.com/question/12955625
#SPJ2
PLEASE HELP! A machine uses filtration to separate a component from orange juice. Which component does the machine most likely separate from the mixture?
A - Pigment
B - Sugar
C - Pulp
D - Water
Answer: c
Explanation: Filtration is technically defined as the process of separating suspended solid matter from a liquid
Pulp is a lignocellulosic fibrous material prepared by chemically or mechanically separating cellulose fibers from wood, fiber crops .
Many commercial juices are filtered to remove fiber or pulp.
The correct answer is C, Pulp.
Orange is an example of a citrus fruit. Every citrus fruit has a pulp. The of pulp a citrus fruit is that stringy content in the endocarp of the fruit .
The pulp of a citrus fruit is where its juice is found.
When you want to prepare orange juice, you need to remove the pulp of the citrus fruit. This is done by filtering out the pulp from the juice.
Filtration is the process of removing larger particles. For a liquid juice, filtration is the process of removing solid particles from the orange juice.
https://brainly.com/question/11403039
A sample of gas is held at constant volume. If the number of moles of this sample of gas is doubled and the pressure of this sample of gas is halved, what happens to the absolute temperature of the gas?
Select one
a. The absolute temperature is doubled.
b. The absolute temperature is halved.
c. The absolute temperature is quadrupled.
d. The absolute temperature is quartered.
e. The absolute temperature stays the same.
Answer:
number of moles of gas increases the volume also increases.
Hãy cho biết giá trị và ý nghĩa của số lượng tử n, l, m, ms khi mô tả trạng thái của electron trong nguyên tử?
A(n) _____, used as part of the stationary phase, has an affinity for the solvent and the chemical components of the mixture. adsorbent eluent Rf factor chromatogram
The Adsorbent is used as part of the stationary phase and has an affinity for the solvent and the chemical components of the mixture.
The adsorbent has a high affinity for solvent and the chemical components of the mixture.
Chromatography is a method of separation in which the mixture of substances is introduced into a mobile phase (solvent). The separation occurs as the solvent interacts with an adsorbent(stationary phase).
The extent of separation of the components of the mixture depends on the extent of interaction between the mobile and the stationary phase . This interaction also determines the retention factor (Rf) of the separation.
For a definition of chromatography, see
https://brainly.com/question/19334271
The fact that a beam of particles was deflected in the presence of an electric
or magnetic force led J.J. Thomson to conclude that the particles had a(n)
O A. large mass
B. electric charge
O C. negligible mass
O D. neutral charge
Answer:
electric charge
Explanation:
Charged particles are deflected in an electric or a magnetic field. The particles discovered by J.J. Thomson were charged particles.
When these charged particles are passed through electric and magnetic fields, deflection occurs depending on the nature of the charge.
A positive charge is deflected towards the negative part of an electric field or the south pole of a magnetic field.
A negative charge is selected towards the positive end of an electric field or the north pole of a magnetic field.
The shape of a molecule is determined by:
A. All of these
B. The number of electron clouds around the atom.
C. The number of bonds.
D. Mutual repulsion between electrons.
The density of an aqueous solution containing 25.0 percent of ethanol (C2H5OH) by mass is 0.950 g/mL. (a) Calculate the molality of this solution. m (b) Calculate its molarity. M (c) What volume of the solution would contain 0.275 mole of ethanol
Answer:
a. 7.24m
b. 5.15M
c. 53.4mL of the solution would contain this amount of ethanol.
Explanation:
Molality, m, is defined as the moles of solute (ethanol, in this case) per kg of solvent.
Molarity, M, are the moles of solute per kg of solvent
To solve this question we need to find the moles of solute in 100g of solution and the volume using its density as follows:
a. Moles ethanol -Molar mass: 46.07g/mol-:
25g ethanol * (1mol/46.07g) = 0.54265 moles ethanol
kg solvent:
100g solution - 25g solute = 75g solvent * (1kg / 1000g) = 0.075kg
Molality:
0.54265 moles ethanol / 0.075kg = 7.24m
b. Liters solution:
100g solution * (1mL / 0.950g) = 105.3mL * (1L / 1000mL) = 0.1053L
Molarity:
0.54265 moles ethanol / 0.1053L = 5.15M
c. 0.275 moles ethanol * (1L / 5.15moles Ethanol) = 0.0534L =
53.4mL of the solution would contain this amount of ethanol
Atoms that have a positive or negative electrical charge are called ________.
Explanation:
They are called or known as cations
If the Ksp of NaCl is experimentally determined to be 43.9, then what is the concentration of Na (in M) when it begins to crystallize out of solution
Answer:
6.63 M
Explanation:
NaCl(s) ---> Na^+(aq) + Cl^-(aq)
Given that [Na^+] = [Cl^-] = s
Where s= concentration of the both ions
Ksp = s^2
s= √Ksp
s= √43.9
s= 6.63 M
The concentration of Na (in M) obtained when it begins to crystallize out of solution is 6.63 M
What is solubility of product?The solubility of product (Ksp) is defined as the concentration of products raised to their coefficient coefficients. This is illustrated below:
mX <=> nY + eZ
Ksp = [Y]^n × [Z]^e
Dissociation equationNaCl(aq) → Na⁺(aq) + Cl¯(aq)
Let the concentration of Na⁺ be yLet the concentration of Cl¯ be yHow to determine the concentration of Na⁺ Solubility of product (Ksp) = 43.9Concentration of Cl¯ = yConcentration of Na⁺ = y =?Ksp = [Na⁺] × [Cl¯]
43.9 = y × y
43.9 = y²
Take the square root of both side
y = √43.9
y = 6.63 M
Thus, the concentration of Na⁺ is 6.63 M
Learn more about solubility of product:
https://brainly.com/question/4530083
Write the complete ground-state electron configuration of I⁻.
Explanation:
here's the answer to your question
Iodine's neutral atom has the following electronic configuration: 1 s² 2 s² 2 p⁶ 3 s² 3 p⁶ 4 s² 3 d¹⁰ 4 p⁶ 5 s² 4 d¹⁰ 5 p⁵. The complete ground-state electron configuration of I⁻ is [Kr]5s² 4d¹⁰ 5p⁶.
What is electronic configuration?Electronic configuration is defined as each electron moves individually within an orbital while being surrounded by an average field produced by all other orbitals. The electron configuration is used to describe an atom's ground state orbitals, but it may also be used to depict an atom that has ionized into a cation or anion by making up for any lost or gained electrons in the orbitals after it.
The ground state electronic configuration is defined as the configuration of lower energy electrons surrounding an atom's nucleus. Ground state is defined as the least energetic state feasible for a physical system. It is important because permits us to determine the location of the excited electrons' departure and return when they release a photon.
Thus, iodine's neutral atom has the following electronic configuration: 1 s² 2 s² 2 p⁶ 3 s² 3 p⁶ 4 s² 3 d¹⁰ 4 p⁶ 5 s² 4 d¹⁰ 5 p⁵. The complete ground-state electron configuration of I⁻ is [Kr]5s² 4d¹⁰ 5p⁶.
To learn more about electronic configuration, refer to the link below:
https://brainly.com/question/14283892
#SPJ2
Why is it difficult to classify dissolving as simply a physical or a chemical change? (1 point)
O Some substances keep the same molecular structure when they break down, and others do not.
O Some substances release energy when they dissolve, and some absorb energy.
O Some substances taste the same after they dissolve, and others do not.
O Some substances keep the same color when they dissolve, and others do not.
Answer:
It is difficult because of C
Explanation:
The correct answer is:Some substances keep the same molecular structure when they break down, and others do not.
Some substances change their form when they dissolve and some do not. Dissolution can sometimes be regarded as a sort of reaction between a chemical substance and water.
Usually, we can consider dissolution of a substance in water as a sort of chemical reaction for some substances. For instance, an ionic substance interacts with water to form ions. similarly, some salts become hydrolysed in water and give acidic/basic solutions as result of that.
However, some substances do not interact with water upon dissolution. They rather remain as molecular entities because they are not composed of ions.
We can see that some substances keep the same molecular structure when they break down, and others do not keep the same molecular structure when they dissolve hence it is difficult to classify dissolving as a physical or a chemical change.
https://brainly.com/question/1161517
