A lens is made with a focal length of -40 cm using a material with index of refraction 1.50. A second lens is made with the SAME GEOMETRY as the first lens, but using a material having refractive index of 2.00. What is the focal length of the second lens

Answers

Answer 1

Answer:

 f = - 20 cm

Explanation:

This exercise asks us for the focal length, which for a lens in air is

                  1 / f = (n₂-n₁) (1 / R₁ - 1 / R₂)

where n₂ is the refractive index of the material, n₁ is the refractive index of the medium surrounding the lens, R₁ and R₂ are the radii of the two surfaces.

In this exercise the medium that surrounds the lens is air n₁ = 1 and the lens material has an index of refraction n₂ = n = 1.50, let's substitute in the expression

                 - 1/40 = (n-1) (1 / R₁ -1 / R₂)

                (1 / R₁ - 1 / R₂) = - 1/40 (n-1)

let's calculate

               (1 / R₁ -1 / R₂) = - 1/40 (1.50 -1)

               (1 / R₁ -1 / R₂) = -1/20

 Now we change the construction material for one with refractive index

n = 2, keeping the radii,

              1 / f = (n-1) (1 / R₁-1 / R₂)

              1 / f = (n-1) (-1/20)

               

let's calculate

             1 / f = (2.00-1) (-1/20)

              1 / f = -1/20

              f = - 20 cm


Related Questions

A certain car traveling 33.0mph skids to a stop in 39m from the point where the brakes were applied. In approximately what distance would the car stop had it been going 66.0mph

Answers

Answer: 156.02 metre.

Explanation:

Give that a certain car traveling 33.0mph skids to a stop in 39m from the point where the brakes were applied.

Let us use third equation of motion,

V^2 = U^2 + 2as

Since the car is decelerating, V = 0

And acceleration a will be negative.

U = 33 mph

S = 39 m

Substitute both into the formula

0 = 33^2 - 2 × a × 39

0 = 1089 - 78a

78a = 1089

a = 1089 / 78

a = 13.96 m/h^2

If we assume that the car decelerate at the same rate.

the distance the car will stop had it been going 66.0mph will be achieved by using the same formula

V^2 = U^2 + 2as

0 = 66^2 - 2 × 13.96 × S

4356 = 27.92S

S = 4356 / 27.92

S = 156.02 m

Therefore, the car would stop at

156.02 m

: A spaceship is traveling at the speed 2t 2 1 km/s (t is time in seconds). It is pointing directly away from earth and at time t 0 it is 1000 kilometers from earth. How far from earth is it at one minute from time t 0

Answers

Answer:

145060km

Explanation: Given that

speed = dx/dt = 2t^2 +1

integrate

x = 2/3t^3 + t + c (c is constant, x is in km, t is in second)

given that at t=0, x = 1000

so 1000 = 2/3 X (0)^3 + 0 + c

or c = 1000

So x = 2/3t^3 + t + 1000

for t = 1 min = 60s

x = 2/3 X 60^3 + 60 + 1000

x = 2/3×216000+ 1060

x = 144000+1060

= 145060km

At one minute, it will be 145060km far from the earth

Equal currents of magnitude I travel into the page in wire M and out of the page in wire N. The direction of the magnetic field at point P which is at the same distance from both wires is

Answers

Answer:

The direction of the magnetic field on point P, equidistant from both wires, and having equal magnitude of current flowing through them will be pointed perpendicularly away from the direction of the wires.

Explanation:

Using the right hand grip, the direction of the magnet field on the wire M is counterclockwise, and the direction of the magnetic field on wire N is clockwise. Using this ideas, we can see that the magnetic flux of both field due to the currents of the same magnitude through both wires, acting on a particle P equidistant from both wires will act in a direction perpendicularly away from both wires.

"Can we consider light wave as a single frequency wave? Either Yes or No, explain the reason of your answer. "

Answers

Answer:

Well, yes.

We can have an isolated light wave that is defined by only one frequency (and one wavelenght). But this is not a really common situation, most of the light that we can see in nature, is actually a composition of different waves with different frequencies.

Even if we have, for example, a red laser, the actual frequency of the light that comes from the laser may be in a range of frequencies, so the actual wave is a composition of different waves with really close frequencies.

An example of a light wave defined by only one frequency can be, for example, the photon that comes out of a change in energy of an electron.

Here we have a single photon, with a single frequency, that is modeled as a single frequency wave.

Each proton-proton cycle generates 26.7 MeV of energy. If 9.9 Watts are generated via by the proton-proton cycle, how many billion neutrinos are produced

Answers

Answer:

4.635 *10^12 Neutrinos

Explanation:

Here in this question, we are to determine the number of neutrinos in billions produced, given the power generated by the proton-proton cycle.

We proceed as follows;

In proton-proton cycle generates 26.7 MeV of energy and in this cycle two neutrinos are produced.

From the question, we are given that

Power P = 9.9 watts = 9.9 J/s

Watts is same as J/s

The number of proton-proton cycles required to generate E energy is N = E / E '

Where E ' = Energy generated in proton-proton cycle which is given as 26.7 Mev in the question

Converting Mev to J, we have

= 26.7 x1.6 x10 -13 J

To get the number N which is the number of proton-proton cycle required, we have;

N = 9.9 /(26.7 x1.6 x10^-13) = 2.32 * 10^12

Since we have two proton cycles( proton-proton), it automatically means 2 neutrinos will be produced.

Therefore number of neutrions produced = 2 x Number of proton-proton cycles = 2 * 2.32 * 10^12 = 4.635 * 10^12 neutrinos

If you stood on a planet having a mass four times higher than Earth's mass, and a radius two times 70) lon longer than Earth's radius, you would weigh:________
A) four times more than you do on Earth.
B) two times less than you do on Earth.
C) the same as you do on Earth
D) two times more than you do on Earth.

Answers

CHECK COMPLETE QUESTION BELOW

you stood on a planet having a mass four times that of earth mass and a radius two times of earth radius , you would weigh?

A) four times more than you do on Earth.

B) two times less than you do on Earth.

C) the same as you do on Earth

D) two times more than you do on Earth

Answer:

OPTION C is correct

The same as you do on Earth

Explanation :

According to law of gravitation :

F=GMm/R^2......(a)

F= mg.....(b)

M= mass of earth

m = mass of the person

R = radius of the earth

From law of motion

Put equation b into equation a

mg=GMm/R^2

g=GMm/R^2

g=GM/R^2

We know from question a planet having a mass four times that of earth mass and a radius two times of earth radius if we substitute we have

m= 4M

r=(2R)^2=4R^2

g= G4M/4R^2

Then, 4in the denominator will cancel out the numerator we have

g= GM/R^2

Therefore, g remain the same

An astronomer is measuring the electromagnetic radiation emitted by two stars, both of which are assumed to be perfect blackbody emitters. For each star she makes a plot of the radiation intensity per unit wavelength as a function of wavelength. She notices that the curve for star A has a maximum that occurs at a shorter wavelength than does the curve for star B. What can she conclude about the surface temperatures of the two stars

Answers

Answer:

Star A has a higher surface temperature than star B.

Explanation:

The effective temperature of a star can be determined by means of its spectrum and Wien's displacement law:

[tex]T = \frac{2.898x10^{-3} m. K}{\lambda max}[/tex] (1)

Where T is the effective temperature of the star and [tex]\lambda_{max}[/tex] is the maximum peak of emission.  

A body that is hot enough emits light as a consequence of its temperature. For example, if an iron bar is put in contact with fire, it will start to change colors as the temperature increase, until it gets to a blue color, that scenario is known as Wien's displacement law. Which establishes that the peak of emission for the spectrum will be displaced to shorter wavelengths as the temperature increase and higher wavelengths as the temperature decreases.

Therefore, star A has a higher surface temperature than star B, as it is shown in equation 1 since T and [tex]\lambda max[/tex] are inversely proportional.

A projectile is shot from the edge of a cliff 80 m above ground level with an initial speed of 60 m/sec at an angle of 30° with the horizontal. Determine the time taken by the projectile to hit the ground below.

Answers

Answer:

8 seconds

Explanation:

Answer:

Explanation:

Going up

Time taken to reach maximum height= usin∅/g

=3 secs

Maximum height= H+[(usin∅)²/2g]

=80+[(60sin30)²/20]

=125 meters

Coming Down

Maximum height= ½gt²

125= ½(10)(t²)

t=5 secs

The place you get your hair cut has two nearly parallel mirrors 6.5 m apart. As you sit in the chair, your head is

Answers

Complete question is;

The place you get your hair cut has two nearly parallel mirrors 6.50 m apart. As you sit in the chair, your head is 3.00 m from the nearer mirror. Looking toward this mirror, you first see your face and then, farther away, the back of your head. (The mirrors need to be slightly nonparallel for you to be able to see the back of your head, but you can treat them as parallel in this problem.) How far away does the back of your head appear to be?

Answer:

13 m

Explanation:

We are given;

Distance between two nearly parallel mirrors; d = 6.5 m

Distance between the face and the nearer mirror; x = 3 m

Thus, the distance between the back-head and the mirror = 6.5 - 3 = 3.5m

Now, From the given values above and using the law of reflection, we can find the distance of the first reflection of the back of the head of the person in the rear mirror.

Thus;

Distance of the first reflection of the back of the head in the rear mirror from the object head is;

y' = 2y

y' = 2 × 3.5

y' = 7

The total distance of this image from the front mirror would be calculated as;

z = y' + x

z = 7 + 3

z = 10

Finally, the second reflection of this image will be 10 meters inside in the front mirror.

Thus, the total distance of the image of the back of the head in the front mirror from the person will be:

T.D = x + z

T.D = 3 + 10

T.D = 13m

A solid block is attached to a spring scale. When the block is suspended in air, the scale reads 21.2 N; when it is completely immersed in water, the scale reads 18. 2 N. What are the volume and density of the block?

Answers

Answer:

7066kg/m³

Explanation:

The forces in these cases (air and water) are: Fa =mg =ρbVg Fw =(ρb −ρw)Vg where ρw = 1000 kg/m3 is density of water and ρb is density of the block and V is its density. We can find it from this two equations:

Fa /Fw = ρb / (ρb −ρw) ρb = ρw (Fa /Fa −Fw) =1000·(1* 21.2 /21.2 − 18.2)

= 7066kg/m³

Explanation:

Answer:

The volume of the block is 306 cm³

The density of the block is 7.07 g/cm³

Explanation:

Given;

weight of block in air, [tex]W_a[/tex] = 21.2 N

Weight of block in water, [tex]W_w[/tex] = 18.2 N

Mass of the block in air;

[tex]W_a = mg[/tex]

21.2 = m x 9.8

m = 21.2 / 9.8

m = 2.163 kg

mass of the block in water;

[tex]W_w = mg[/tex]

18.2 = m x 9.8

m = 18.2 / 9.8

m = 1.857 kg

Apply Archimedes principle

Mass of object in air  - mass of object in water = density of water   x  volume                  of object

2.163 kg - 1.857 kg = 1000 kg/m³ x Volume of block

0.306 kg = 1000 kg/m³ x Volume of block

Volume of the block = [tex]\frac{0.306 \ kg}{1000 \ kg/m^3}[/tex]

Volume of the block = 3.06 x 10⁻⁴ m³

Volume of the block = 306 cm³

Determine the density of the block

[tex]Density = \frac{mass}{volume} \\\\Density =\frac{2163 \ g}{306 \ cm^3} \\\\Density = 7.07 \ g/cm^3[/tex]

What physical feature of a wave is related to the depth of the wave base? What is the difference between the wave base and still water level?

Answers

Answer:

physical feature of a wave is related to the depth of the wave base is The circular orbital motion

B. The wave base is the depth, and the still water level is the horizontal level

You shine unpolarized light with intensity 52.0 W/m2 on an ideal polarizer, and then the light that emerges from this polarizer falls on a second ideal polarizer. The light that emerges from the second polarizer has intensity 15.0 W/m2. Find the intensity of the light that emerges from the first polarizer.

Answers

Answer:

The intensity of light from the first polarizer  is [tex]I_1 = 26 W/m^2[/tex]

Explanation:

  The intensity of the unpolarized light is  [tex]I_o = 52.0 \ W/m^2[/tex]

   

Generally the intensity of light that emerges from the first polarized light is

            [tex]I_1 = \frac{I_o}{2 }[/tex]

 substituting values

             [tex]I_1 = \frac{52. 0}{2 }[/tex]

             [tex]I_1 = 26 W/m^2[/tex]

You have two capacitors and want to connect them across a voltage source (battery) to store the maximum amount of energy. Should they be connected in series or in parallel?

Answers

Answer:

In parallel

Explanation:

Ctotal = C1 + C2 + ... + Cn

The starter motor of a car engine draws a current of 140 A from the battery. The copper wire to the motor is 4.20 mm in diameter and 1.2 m long. The starter motor runs for 0.760 s until the car engine starts.Required:a. How much charge passes through the starter motor? b. How far does an electron travel along the wire while the starter motor is on?(mm)

Answers

Answer:

(a)106.4C

b)0.5676mm

Explanation:

(a)To get the charge that have passed through the starter then The current will be multiplied by the duration

I= current

t= time taken

Q= required charge

Q= I*t = 140*0.760 = 106.C

(b) b. How far does an electron travel along the wire while the starter motor is on?(mm)

diameter of the conductor is 4.20 mm

But Radius= diameter/2= 4.20/2=

The radius of the conductor is 2.1mm, then if we convert to metre for consistency same then

radius of the conductor is 0.0021m.

We can now calculate the area of the conductor which is

A = π*r^2

= π*(0.0021)^2 = 13.85*10^-6 m^2

We can proceed to calculate the current density below

J = 140/13.85*10^-6 = 10108303A/m

According to the listed reference:

Where e= 1.6*10^-19

n= 8.46*10^28

Vd = J/(n*e) = 10108303/ ( 8.46*10^28 * 1.6*10^-19 ) =0.0007468m/s=0 .7468 mm/s

Therefore , the distance traveled is:

x = v*t = 0.7468 * 0.760 = 0.5676mm

(a) The charge passes through the starter motor is 106.4C.

(b) An electron travel along the wire while the starter motor is on 0.5676mm.

Electron

Answer (a)

I= current

t= time taken

Q= required charge

Q= I*t

Q= 140*0.760

Q= 106.C

Answer (b)

The n electron travel along the wire while the starter motor is on:

Diameter of the conductor is 4.20 mm

Radius= diameter/2= 4.20/2

Radius =2.1mm

Radius of the conductor is 0.0021m.

A = π*r^2

A= π*(0.0021)^2

A= 13.85*10^-6 m^2

Where e= 1.6*10^-19

n= 8.46*10^28

Vd = J/(n*e) = 10108303/ ( 8.46*10^28 * 1.6*10^-19 )

Vd  =0.0007468m/s

Vd =0 .7468 mm/s

The distance traveled is:

x = v*t

x= 0.7468 * 0.760

x = 0.5676mm

Learn more about "Electron":

https://brainly.com/question/1255220?referrer=searchResults

The A block, with negligible dimensions and weight P, is supported by the coordinate point (1.1/2) of the parabolic fixed grounded surface, from equation y = x^2/2 If the block is about to slide, what is the coefficient of friction between it and the surface; determine the force F tangent to the surface, which must be applied to the block to start the upward movement.

Answers

Answer:

μ = 1

F = P√2

Explanation:

The parabola equation is: y = ½ x².

The slope of the tangent is dy/dx = x.

The angle between the tangent and the x-axis is θ = tan⁻¹(x).

At x = 1, θ = 45°.

Draw a free body diagram of the block.  There are three forces:

Weight force P pulling down,

Normal force N pushing perpendicular to the surface,

and friction force Nμ pushing up tangential to the surface.

Sum of forces in the perpendicular direction:

∑F = ma

N − P cos 45° = 0

N = P cos 45°

Sum of forces in the tangential direction:

∑F = ma

Nμ − P sin 45° = 0

Nμ = P sin 45°

μ = P sin 45° / N

μ = tan 45°

μ = 1

Draw a new free body diagram.  This time, friction force points down tangential to the surface, and applied force F pushes up tangential to the surface.

Sum of forces in the tangential direction:

∑F = ma

F − Nμ − P sin 45° = 0

F = Nμ + P sin 45°

F = (P cos 45°) μ + P sin 45°

F = P√2

Distinguish between physical and chemical changes. Include examples in your explanations.

Answers

Answer:

Chemical changes are recognized when a substance changes its properties permanently and it cannot be the same substance as before.

Instead the physical changes implies that if you can return to the same substance through a reverse process.

Explanation:

A chemical change is, by example, a combustion, if a sheet of paper burns, its result is ashes, the ashes cannot go back to being a sheet of paper because its properties changed, heat energy was generated that changed matter permanently.

A physical change, by example, is that of freezing water, the water becomes ice, but this can easily become water again if the temperature is increased, its properties do not change and the chemistry of the substance does not change.

A chemical change takes place when a chemical reaction takes place, while when a matter changes forms but not the chemical identity then a physical change takes place.  

A product or a new compound formation takes place from a chemical change as the rearrangement of atoms takes place to produce novel chemical bonds.  

• In a chemical change always a chemical reaction takes place.  

• Some of the chemical changes examples are souring milk, burning wood, digesting food, mixing acid and base, cooking food, etc.  

• In a physical change no new chemical species form.  

• The changing of the state of a pure substance between liquid, gas, or solid is a physical change as there is no change in the identity of the matter.  

• Some of the physical changes are melting of ice, tempering of steel, breaking a bottle, crumpling a sheet of aluminum foil, boiling water, and shredding paper.  

Thus, a new substance is formed during a chemical change, while a physical change does not give rise to a new substance.  

To know more about:

https://brainly.com/question/7279398

Two sources of light of wavelength 700 nm are 9 m away from a pinhole of diameter 1.2 mm. How far apart must the sources be for their diffraction patterns to be resolved by Rayleigh's criterion

Answers

Answer:

The distance is  [tex]D = 0.000712 \ m[/tex]

Explanation:

From the question we are told that

    The wavelength of  the  light source is  [tex]\lambda = 700 \ nm = 700 *10^{-9} \ m[/tex]

     The distance from a pin hole is  [tex]x = 9\ m[/tex]

       The  diameter of the pin  hole is  [tex]d = 1.2 \ mm = 0.0012 \ m[/tex]

     

Generally the distance which the light source need to be in order for their diffraction patterns to be resolved by Rayleigh's criterion is

mathematically represented as

              [tex]D = \frac{1.22 \lambda }{d }[/tex]

substituting values

             [tex]D = \frac{1.22 * 700 *10^{-9} }{ 0.0012 }[/tex]

             [tex]D = 0.000712 \ m[/tex]

Can you come up with a mathematical relationship, based on your data that shows the relationship between distance from the charges and electric field strength?

Answers

Answer:

Explanation:

This question appears incomplete because of the absence of the data been talked about in the question. However, there is a general ruling here and it can be applied to the data at hand.

If an increase in the distance of charges (let's denote with "d") causes the electric field strength (let's denote with"E") to increase, then the mathematical representation can be illustrated as d ∝ E (meaning distance of charge is directly proportional to electric field strength).

But if an increase in the distance of the charges causes the electric field strength to decrease, then the mathematical representation can be illustrated as d ∝ 1/E (meaning distance of charge is inversely proportional to electric field strength).

A scatterplot can also be used to determine this. If there is a positive correlation (correlation value is greater than zero but less than or equal to 1) on the graph, then it is illustrated as "d ∝ E" BUT if there is a negative correlation (correlation value is less than zero but greater than or equal to -1), then it can be illustrated as "d ∝ 1/E".

You are performing an experiment that requires the highest-possible magnetic energy density in the interior of a very long current-carrying solenoid. Which of the following adjustments increases the energy density?a. Increasing only the length of the solenold while keeping the turns per unit lengh flxed. b. Increasing the number of turns per unit length on the solenold. c. Increasing the cross-sectional area of the solenoid. d. None of these. e. Increasing the current in the solenoid.

Answers

Answer:

The correct choice is B & E.  

Explanation:

A solenoid is a coil of wire (usually copper) which is used as an electromagnet. Solenoids are used to convert electrical energy to mechanical energy. When this type of device is created it is also called a solenoid. One can increase the energy density within the solenoid or the coil by upping the electric current in the coil.

Cheers!

A cyclist moves effortlessly at a constant speed of 12 m / s, but enters a muddy area where the coefficient of kinetic friction is 0.60. Will the rider leave the muddy area without having to pedal if the mud extends 11m? If so, how fast will it emerge?

Answers

Answer:

3.5 m/s

Explanation:

There are 3 forces on the cyclist:

Weight force mg pulling down,

Normal force N pushing up,

and friction force Nμ pushing left.

Sum of forces in the y direction:

∑F = ma

N − mg = 0

N = mg

∑F = ma

-Nμ = ma

-mgμ = ma

a = -gμ

a = -(10 m/s²)(0.60)

a = -6 m/s²

Velocity reached at end of 11 m:

v² = v₀² + 2aΔx

v² = (12 m/s)² + 2 (-6 m/s²) (11 m)

v = √12 m/s

v ≈ 3.5 m/s

A system of four particles moves along a dimension. The center of mass is at rest, and the particles do not interact with any objects outside of the system. Find the velocity of v4 at t=2.83 seconds given the details for the motion of particles 1,2,3

Answers

Answer:

v = - 14.08 m / s

Explanation:

The definition of center of mass is

        [tex]x_{cm}[/tex] = 1 /M  ∑sun [tex]x_{i} m_{i}[/tex]

where M is the total mass of the system and [tex]x_{i}[/tex] and [tex]m_{i}[/tex] are the position and mass of each component.

The velocity of the center of mass can be found by deriving this expression with respect to time

         [tex]v_{cm}[/tex] = 1 / M ∑ m_{i} [tex]v_{i}[/tex] vi

let's find the total mass

          M = m₁ + m₂ + m₃ + m₄

          M = 1.45 + 2.81 +3.89 + 5.03

          m = 13.18 kg

let us substitute in the velocity of the center of mass [tex]v_{cm}[/tex] = 0

          0 = 13.18 (m₁ v₁ + m₂ v₂ + m₃v₃ + m₄v₄)

          v₄ = - (m₁ v₁ + m₂ v₂ + m₃v₃) / m₄

let's substitute the given values

v₄ = -[1.45 (6.09 +0.299 t) +2.81 (7.83 + 0.357t) +3.89 (8.09 + 0.405 t)] / 5.03

They ask us for the calculations for a time t = 2.83 s

          v₄ = - [8.8305 + 1.227 + 22.00 + 2.839 + 31.47 +4.4585] / 5.03

          v = - 14.08 m / s

The velocity of the particle 4 at time, t = 2.83 s, is -14.1 m/s.

The given parameters;

[tex]m_1 = 1.45 \ kg, \ \ v_1(t) = (6.09 \ m/s) + (0.299 \ m/s^2)\times t\\\\m_2 = 2.81 \ kg, \ \ v_2(t) = (7.83 \ m/s) + (0.357 \ m/s^2)\times t \\\\m_3 = 3.89 \ kg, \ \ v_3(t) = (8.09 \ m/s) + (0.405 \ m/s^2)\times t\\\\m_4 = 5.03 \ kg[/tex]

The velocity of the center mass of the particles is calculated as;

[tex]M_{cm}V_{cm} = m_1v_1 + m_2 v_2 + m_3v_3 + m_4v_4\\\\V_{cm} = \frac{m_1v_1 + m_2 v_2 + m_3v_3 + m_4v_4}{M_{cm}} \\\\0 = \frac{m_1v_1 + m_2 v_2 + m_3v_3 + m_4v_4}{M_{cm}}\\\\m_1v_1 + m_2 v_2 + m_3v_3 + m_4v_4 = 0\\\\m_4v_4 = -(m_1v_1 + m_2 v_2 + m_3v_3)\\\\v_4 = \frac{-(m_1v_1 + m_2 v_2 + m_3v_3)}{m_4}[/tex]

The velocity of particle 1 at time, t = 2.83 s;

[tex]v_1 = 6.09 \ + \ 0.299\times 2.83\\\\v_1 = 6.94 \ m/s[/tex]

The velocity of particle 2 at time, t = 2.83 s;

[tex]v_2 = 7.83\ + \ 0.357\times 2.83\\\\v_2 = 8.84 \ m/s[/tex]

The velocity of particle 3 at time, t = 2.83 s;

[tex]v_3 = 8.09\ + \ 0.405 \times 2.83\\\\v_3 = 9.24 \ m/s[/tex]

The velocity of the particle 4 at time, t = 2.83 s;

[tex]v_4 = \frac{-(m_1v_1 + m_2v_2 + m_3v_3)}{m_4} \\\\v_4 = \frac{-(1.45\times 6.94\ + \ 2.81\times 8.84\ + \ 3.89 \times 9.24)}{5.03} \\\\v_4 = -14 .1 \ m/s[/tex]

Thus, the velocity of the particle 4 at time, t = 2.83 s, is -14.1 m/s.

Learn more here:https://brainly.com/question/22698801

At what rate must Uranium 235 undergo fission by neutron bombardment to generate energy at a rate of 100 W (1 W

Answers

Complete Question

At what rate must Uranium 235 undergo fission by neutron bombardment to generate energy at a rate of 100 W (1 W = 1 J/s)? Assume each fission reaction releases 200 MeV of energy.

Answer

a. Approximately [tex]5*10^{10}[/tex] fissions per second.

b. Approximately [tex]6*10^{12 }[/tex]fissions per second.

c. Approximately [tex]4*10^{11}[/tex] fissions per second.

d. Approximately [tex]3*10^{12}[/tex] fissions per second.

e. Approximately[tex]3*10^{14}[/tex] fissions per second.

Answer:

The correct option is  d

Explanation:

From the question we are told that

       The energy released by each fission reaction [tex]E = 200 \ MeV = 200 *10^{6} * 1.60 *10^{-19} =3.2*10^{-11} \ J /fission[/tex]

Thus to generated  [tex]100 \ J/s[/tex] i.e  (100 W  ) the rate of fission is  

              [tex]k = \frac{100}{3.2 *10^{-11} }[/tex]

              [tex]k =3*10^{12} fission\ per \ second[/tex]

Six automobiles are initially traveling at the indicated velocities. The automobiles have different masses and velocities. The drivers step on the brakes and all automobiles are brought to rest.Automobile 1: 500kg, 10m/sAutomobile 2: 2000kg, 5m/sAutomobile 3: 500kg, 20m/sAutomobile 4: 1000kg, 20m/sAutomobile 5: 1000kg, 10m/sAutomobile 6: 4000kg, 5m/sRequired:a. Rank these automobiles based on the magnitude of their momentum before the brakes are applied, from largest to smallest.b. Rank these automobiles based on the magnitude of the impulse needed to stop them, from largest to smallest.c. Rank the automobiles based on the magnitude of the force needed to stop them, from largest to smallest.

Answers

Answer:

A. largest: (4000 kg, 5 m/s; 1000 kg, 20 m/s)

medium: (2000 kg, 5 m/s; 500 kg, 20 m/s; 1000 kg, 10 m/s)

smallest: (500 kg, 10 m/s)

B. largest: (4000 kg, 5 m/s; 1000 kg, 20 m/s)

medium: (2000 kg, 5 m/s; 500 kg, 20 m/s; 1000 kg, 10 m/s)

smallest: (500 kg, 10 m/s)

C. You can't say anything about the forces required until we know about the time frames required for each one to stop. So If they all stopped in the same time interval, then the rankings are the same.

A large reflecting telescope has an objective mirror with a 14.0 m radius of curvature. What angular magnification in multiples does it produce when a 3.25 m focal length eyepiece is used? ✕

Answers

Answer:

The magnification is  [tex]m = -2.15[/tex]

Explanation:

From the question we are told that

   The  radius is  [tex]r = 14.0 \ m[/tex]

    The  focal length eyepiece is  [tex]f_e = 3.25 \ m[/tex]

Generally the objective focal length is mathematically represented as

        [tex]f_o = \frac{r}{2}[/tex]

=>     [tex]f_o = \frac{14}{2}[/tex]

=>     [tex]f_o = 7 \ m[/tex]

The  magnification is mathematically represented as

      [tex]m = - \frac{f_o }{f_e }[/tex]

=>    [tex]m = - \frac{7 }{ 3.25 }[/tex]

=>   [tex]m = -2.15[/tex]

How long will it take a spacecraft travelling at 99% the speed of light (gamma = 7) to reach

the star Sirius which is 8.6 light-years away according to people on Earth ? How long will it

take according to the crew of the ship?

Answers

Answer:

The time taken is  [tex]t = 2.739 *10^{8} \ s[/tex]

Explanation:

From the question we are told that

    The speed of the spacecraft is [tex]v = 0.99c[/tex]

    where c is the speed of light with value [tex]c = 3.0*10^{8} \ m/s[/tex]

    =>   [tex]v = 0.99 * 3.0 *10^{8 } = 2.97*10^{8}\ m/s[/tex]

    The distance of Sirius is [tex]d = 8.6 \ light-years = 8.6 * 9.461*10^{15}= 8.135*10^{16} \ m[/tex]

   

Generally the time taken is mathematically represented as

       [tex]t = \frac{d}{v}[/tex]

substituting values

      [tex]t = \frac{8.136 *10^{16}}{2.97 *10^{8}}[/tex]

      [tex]t = 2.739 *10^{8} \ s[/tex]

which category would a person who has an IQ of 84 belong ?

Answers

answer: below average

An electron is trapped between two large parallel charged plates of a capacitive system. The plates are separated by a distance of 1 cm and there is vacuum in the region between the plates. The electron is initially found midway between the plates with a kinetic energy of 11.2 eV and with its velocity directed toward the negative plate. How close to the negative plate will the electron get if the potential difference between the plates is 100 V? (1 eV = 1.6 x 10-19 J)

Answers

Answer:

The electron will get at about 0.388 cm (about 4 mm) from the negative plate before stopping.

Explanation:

Recall that the Electric field is constant inside the parallel plates, and therefore the acceleration the electron feels is constant everywhere inside the parallel plates, so we can examine its motion using kinematics of a constantly accelerated particle. This constant acceleration is (based on Newton's 2nd Law:

[tex]F=m\,a\\q\,E=m\,a\\a=\frac{q\,E}{m}[/tex]

and since the electric field E in between parallel plates separated a distance d and under a potential difference [tex]\Delta V[/tex], is given by:

[tex]E=\frac{\Delta\,V}{d}[/tex]

then :

[tex]a=\frac{q\,\Delta V}{m\,d}[/tex]

We want to find when the particle reaches velocity zero via kinematics:

[tex]v=v_0-a\,t\\0=v_0-a\,t\\t=v_0/a[/tex]

We replace this time (t) in the kinematic equation for the particle displacement:

[tex]\Delta y=v_0\,(t)-\frac{1}{2} a\,t^2\\\Delta y=v_0\,(\frac{v_0}{a} )-\frac{a}{2} (\frac{v_0}{a} )^2\\\Delta y=\frac{1}{2} \frac{v_0^2}{a}[/tex]

Replacing the values with the information given, converting the distance d into meters (0.01 m), using [tex]\Delta V=100\,V[/tex], and the electron's kinetic energy:

[tex]\frac{1}{2} \,m\,v_0^2= (11.2)\,\, 1.6\,\,10^{-19}\,\,J[/tex]

we get:

[tex]\Delta\,y= \frac{1}{2} v_0^2\,\frac{m (0.01)}{q\,(100)} =11.2 (1.6\,\,10^{-19})\,\frac{0.01}{(1.6\,\,10^{-19})\,(100)}=\frac{11.2}{10000} \,meters=0.00112\,\,meters[/tex]Therefore, since the electron was initially at 0.5 cm (0.005 m) from the negative plate, the closest it gets to this plate is:

0.005 - 0.00112 m = 0.00388 m [or 0.388 cm]

Monochromatic light is incident on a pair of slits that are separated by 0.220 mm. The screen is 2.60 m away from the slits. (Assume the small-angle approximation is valid here.)
(a) If the distance between the central bright fringe and either of the adjacent bright fringes is 1.97 cm, find the wavelength of the incident light.
(b) At what angle does the next set of bright fringes appear?

Answers

Answer:

a

   [tex]\lambda = 1.667 nm[/tex]

b

     [tex]\theta = 0.8681^o[/tex]

Explanation:

From the question we are told that

   The distance of separation is [tex]d = 0.220 \ mm = 0.00022 \ m[/tex]

    The  is distance of the screen from the slit is  [tex]D = 2.60 \ m[/tex]

    The distance between the central bright fringe and either of the adjacent bright   [tex]y = 1.97 cm = 1.97 *10^{-2}\ m[/tex]

Generally  the condition for constructive interference is  

      [tex]d sin \tha(\theta ) = n \lambda[/tex]

From the question we are told that small-angle approximation is valid here.

So    [tex]sin (\theta ) = \theta[/tex]

=>        [tex]d \theta = n \lambda[/tex]

=>        [tex]\theta = \frac{n * \lambda }{d }[/tex]

Here n is the order of maxima and the value is  n =  1 because we are considering the central bright fringe and either of the adjacent bright fringes

Generally the distance between the central bright fringe and either of the adjacent bright  is mathematically represented as

         [tex]y = D * sin (\theta )[/tex]

From the question we are told that small-angle approximation is valid here.

So

       [tex]y = D * \theta[/tex]

=>   [tex]\theta = \frac{ y}{D}[/tex]

So

     [tex]\frac{n * \lambda }{d } = \frac{y}{D}[/tex]

     [tex]\lambda =\frac{d * y }{n * D}[/tex]

substituting values

       [tex]\lambda = \frac{0.00022 * 1.97*10^{-2} }{1 * 2.60 }[/tex]

        [tex]\lambda = 1.667 *10^{-6}[/tex]

        [tex]\lambda = 1.667 nm[/tex]

In the b part of the question we are considering the next set of bright fringe so  n=  2

    Hence

     [tex]dsin (\theta ) = n \lambda[/tex]

    [tex]\theta = sin^{-1}[\frac{ n * \lambda }{d} ][/tex]

    [tex]\theta = sin^{-1}[\frac{ 2 * 1667 *10^{-9}}{ 0.00022} ][/tex]

    [tex]\theta = 0.8681^o[/tex]

Determine the orbital period (in hours) of an observation satellite in a circular orbit 1,787 km above Mars.

Answers

Answer:

T = 3.14 hours

Explanation:

We need to find the orbital period (in hours) of an observation satellite in a circular orbit 1,787 km above Mars.

We know that the radius of Mars is 3,389.5 km.

So, r = 1,787 + 3,389.5 = 5176.5 km

Using Kepler's law,

[tex]T^2=\dfrac{4\pi ^2}{GM}r^3[/tex]

M is mass of Mars, [tex]M=6.39\times 10^{23}\ kg[/tex]

So,

[tex]T^2=\dfrac{4\pi ^2}{6.67\times 10^{-11}\times 6.39\times 10^{23}}\times (5176.5 \times 10^3)^3\\\\T=\sqrt{\dfrac{4\pi^{2}}{6.67\times10^{-11}\times6.39\times10^{23}}\times(5176.5\times10^{3})^{3}}\\\\T=11334.98\ s[/tex]

or

T = 3.14 hours

So, the orbital period is 3.14 hours

If a transformer has 50 turns in the primary winding and 10 turns on the secondary winding, what is the reflected resistance in the primary if the secondary load resistance is 250 W?

Answers

Answer:

The reflected resistance in the primary winding is 6250 Ω

Explanation:

Given;

number of turns in the primary winding, [tex]N_P[/tex] = 50 turns

number of turns in the secondary winding, [tex]N_S[/tex] = 10 turns

the secondary load resistance, [tex]R_S[/tex] = 250 Ω

Determine the turns ratio;

[tex]K = \frac{N_P}{N_S} \\\\K = \frac{50}{10} \\\\K = 5[/tex]

Now, determine the reflected resistance in the primary winding;

[tex]\frac{R_P}{R_S} = K^2\\\\R_P = R_SK^2\\\\R_P = 250(5)^2\\\\R_P = 6250 \ Ohms[/tex]

Therefore, the reflected resistance in the primary winding is 6250 Ω

Other Questions
READ THE CHAPTERS 1, 2, 3, 4,5 FROM THE BOOK 1 JOHN IN YOUR BIBLE AND ANSWER THE FOLLOWING QUESTIONS: Why did John write this epistle? (1:4, 2:1, 2:26) In this epistle, what did John say that God is and begins with the letters "L" and "L"? (1: 5, 4: 8) What kind of person does Juan call a liar or one who lies? (1:10, 2: 4, 22) What did Juan say his hands had felt? (1: 1) What did John say that cleanses us from all sin? (1: 7) If a Christian sins, what should he do? (1: 9) Everything in the world, what does Juan say it is? (2:16) How did Juan call his readers? (2:12, 13) How does John define sin? (3: 4) What does John say about those who are born again? (3: 9) What Old Testament character does John use as an example of those who do not love one another? (3:12) What does Juan call the person who hates his brother? (3:15) How does John say that we should love? (3:18) Why should we not believe every spirit, but rather test the spirits if they are from God? (4: 1) Who or what is greater than the one in the world? (4: 4) What does John say about the commandments of God? (5: 4) Who are the three who bear witness on earth? (5:8) What are the two word phrases that John used at least five times in the last chapter of I John? (5: 2,15,18-20) What does John say we should guard against at the end of this epistle? (5:21) f(x) = x2. What is g(x)? Attorney represented Baker in a claim involving a breach of Baker's employment contract. The case was settled without suit being filed. The proceeds of the settlement were paid directly to Baker~ who subsequently paid Attorney in full for Attorney's fee and expenses. Thereafter, Attorney did no other work for Baker. Baker is now being audited by the Internal Revenue Service (IRS). The IRS has asked Attorney for details of the settlement, including the amount claimed for each item of damage and the amounts paid for the items. Attorney reported the request to Baker who told Attorney not to provide the information to the IRS. Is it proper for Attorney to furnish the information to the IRS what are the squares from one to twenty The length of a rectangle is represented by the function L(x) = 4x. The width of that same rectangle is represented by the function W(x) = 7x2 4x + 2. Which of the following shows the area of the rectangle in terms of x? (L + W)(x) = 7x2 + 2 (L + W)(x) = 7x2 8x + 2 (L W)(x) = 28x3 16x2 + 8x (L W)(x) = 28x3 4x + 2 BRAINLIEST, THANKS AND 5 STARS IF ANSWERED BOTH CORRECTLYWhich set of points represents a function? A. (-5, -4), (-4, -3), (-3, -2), (-2, -1) B. (-6, 2), (6, -2) (-5, 3), (-5, -3) C. (8, -1), (8, 2), (8, -3), (8, 4) D. (1, 3), (-4, 4), (3, -2), (1, 0) Which set of points represents a function? A. (2, -5), (4, 0), (7, 0), (2, 5) B. (-1, 4), (2, -4), (-1, -4), (-2, 4) C. (-5, -1), (-2, -1), (1, -1), (4, -1) D. (3, -5), (3, -1), (3, 2), (3, 4) !50 POINTS! GIVE REAL ANSWER OR I REPORT PLZ NO TROLLS! An executive drove from his home at an average speed of 35 mph to an airport where a helicopter was waiting. The executive then boarded the helicopter and flew to the corporate offices at an average speed of 78 mph. The entire distance from his home to the office was 169.5 miles. If the executive spent the same amount of time in the car as he did the helicopter, how long did it take the executive to get to work? A company has net income of $925,000; its weighted-average common shares outstanding are 185,000. Its dividend per share is $0.70, its market price per share is $93, and its book value per share is $83.50. Its price-earnings ratio equals: NEED HELP URGENT!! Which of the following was NOT a major cause of the new Red Scare in America? A. The Korean War B. The U-2 Plane incident C. The Alger Hiss case D. The Rosenberg spy trial what is the answer to x2 = 121. A student wants to create a 6.0V DC battery from a 1.5V DC battery. Can this be done using a transformer alone Firm J has net income of $77,605, sales of $935,000, and average total assets of $467,500. Required: Calculate Firm Js margin, turnover, and return on investment (ROI). Which set of integers represents the lengths of the sides of an isosceles triangle? A. {6,6,5} B. {3,4,5} C. {15,5,10} D. {1,1,3} Question #3: Make a sentence by adding the correct group of words. _______ while the water boiled. A.Mother, stirring and stirring, B.Mother stirred the rice C.Mother System of linear inequalities An October sales forecast projects 7,000 units are going to be sold at a price of $11.50 per unit. The desired ending inventory in units is 15% higher than the beginning inventory of 1,000 units. Total October sales are anticipated to be a.$70,000 b.$80,500 c.$92,000 d.$69,000 An aphorism is a cleverly worded statement that is meant to trick the listener into believing a Lie True False You are an investor who wants to form a portfolio that lies to the right of the "optimal" minimum standard deviation portfolio on the efficient frontier. You must: 0 / 1 puntos Invest only in risky securities. Borrow money at the risk-free rate, invest in the minimum standard deviation portfolio and, in addition, only in risky securities. Borrow money at the risk-free rate and invest everything in the minimum standard deviation portfolio. Invest only in risk-free securities. The Bohr model pictures a hydrogen atom in its ground state as a proton and an electron separated by the distance a0 = 0.529 1010 m. The electric potential created by the electron at the position of the proton is The leadership role of women in social movements was likely an effect of:O A. Government programs that trained and supported women.O B. The organization of women voters.O C. Limited opportunities available to women in other areas of publiclife.O D. The growing number of women elected representatives.