A cylindrical piece of steel 75 mm (3 in.) in diameter is to be austenitized and quenched such that a minimum hardness of 40 HRC is to be produced throughout the entire piece. Of the alloys 8660, 8640, 8630, and 8620, which will qualify if the quenching medium is (a) moderately agitated water and (b) moderately agitated oil

Answers

Answer 1

Answer:

a) 8660 and 8640 alloys

b)  8660 alloy

Explanation:

Diameter of a cylindrical piece of steel = 75 mm ( 3 in )

Equivalent distance from quenched end for the center position is about 17 mm

a) If the quenching medium is moderately agitated water the alloys that will qualify are : 8660 and 8640 alloys  because these are the two alloys that would have a minimum of 40 HRC at the center and also throughout the cylinder

b) if the quenching medium is a moderately agitated oil the alloy that will qualify is : 8660 alloy . because it is the only alloy that will maintain a minimum of 40 HRC at the center and also throughout the entire cylinder.


Related Questions

What is the following diagram called?

Answers

Answer:

business

Explanation:

because shopping has great income

Answer:

is ur question right

Explanation:

is ur question right

is ur question right

if a person is injured at the hospital during a natural disaster a correct action to take is ​

Answers

first check that you and the casualty aren't in any danger. If you are, make the situation safe. When it's safe to do so, assess the casualty and, if necessary, dial 999 or 112 for an ambulance. You can then carry out basic first aid and shift to another hospital




That’s what I learnt sooo..

The end of the industrial robotic arm extends along the path (r = 2 + 2 cos (5t)) m. At the instant ( 0 = 0.8t ) radians. When the arm is located at (t = 0.85) second Determine the velocity and acceleration of the object A at this instant.​

Answers

Answer:

  v = 8.95 rad / s,    a = 22.3 rad / s²

Explanation:

This is an exercise in kinematics, where we must use the definitions of velocity and acceleration

          v = dr / dt

       

we perform the derivative

          v = 0+ 2 (-sin 5t) 5

          v = -10 sin 5t

we calculate for t = 0.85 t,

remember angles are in radians

           v = -10 sin (5 0.85)

           v = 8.95 rad / s

acceleration is defined by

           a = dv / dt

             

we perform the derivatives

          a = -10 (cos 5t) 5

          a = - 50 cos 5t

we calculate for t = 0.85 s

          a = -50 are (5 0.85)

          a = 22.3 rad / s²

Side milling cutter is an example of ______ milling cutter.

Answers

Answer:

special type

Explanation:

As per the classification of milling cutters. This cutter can handle deep and long open slots in a more comfortable manner, which increase the productivity.

2 Air enters the compressor of a cold air-standard Brayton cycle at 100 kPa, 300 K, with a mass flow rate of 6 kg/s. The compressor pressure ratio is 10, and the turbine inlet temperature is 1400 K. The turbine and compressor each have isentropic efficiencies of 80%. For k 5 1.4, calculate (a) the thermal efficiency of the cycle. (b) the back work ratio. (c) the net power developed, in kW. (d) the rates of exergy destruction in the compressor and turbine, respectively, each in kW, for T0 5 300 K.

Answers

You can see and download from the link

https://tlgur.com/d/GYYVL5lG

Please don't forget to put heart ♥️

If a corporation is socially responsible, it will develop and implement a sustainability plan and communicate it to stakeholders.

True
False

Answers

Answer:

True

Explanation:

All big companies are pretty much required in today's day and ages to complete these reports whether they truly believe it.

True or false: You can create a network with two computers.



Answer
True

Answers

To create a computer network, you must have at least two computers. ... A protocol is a standard set of rules and procedures for the control of communications in a network. TRUE. Two computers using TCP/IP can communicate even if they are based on different hardware and software platforms. So your right :)

Hope this helps :)
True u must use two computers

Work to be performed can come from the work package level of the work breakdown structure as well as other sources. Which of these is NOT a source of authorized work to be performed?

a. Scope creep
b. Defect repairs
c. Preventive actions
d. Corrective actions

Answers

A project is meant to achieve clearly defined goals within present constraints

The correct option for the source of work in a project which is NOT a source of authorized work to be performed is option (a)

a. Scope creep

The reason for the selecting the above option is as follows;

In project management, alongside work planned in a work package, authorized work to be performed can come from;

The repairing of defects found in completed work and which is a requirement for the project to be approvePreventive actions, that are meant to mitigate factors that affect the project timeline and costCorrective actions which include actions meant to rectify parts of the project that produce an error outcome

A scope creep, however, is generally is due to the inclusion of the end

users of the project at a time that is behind schedule, insufficient analysis of

the requirements, and project complexity underestimation. and consists of

changes made after a project has commenced

A scope creep therefore, changes the amount of work to be done which

therefore alters the project timeline, and due to project, budgetary, and

end user constraints, CANNOT be a source of authorized work to be

performed

The correct option for the source that is NOT a authorized work to be performed is option a. Scope creep

Learn more about scope creep here:

https://brainly.com/question/14061926

A steam turbine generator unit is used to produce electricity, where steam enters the turbine with a velocity of 30 m/s and enthalpy (internal energy) of 3348 kJ/kg. The 1 steam leaves the turbine as a mixture of vapor and liquid having a velocity of 60 m/s and an enthalpy of 2550 kJ/kg. The flow through the turbine is adiabatic, and changes in elevation are negligible. Determine the work output from the turbine, if the mass flow rate is 5kg/s.

Answers

Answer:

3.983 MW

Explanation:

Given that:

At the inlet:

Velocity (v₁) = 30 m/s

Enthalpy (h₁) = 3348 kJ/kg

At the outlet:

Velocity (v₂) = 60 m/s

Enthalpy (h₂) = 2550 kJ/kg

Mass flow rate (m) = m₁ = m₂ = 5kg/s

According to the steady flow energy equation:

[tex]Q+ m_1 (h_1 + \dfrac{v_1^2}{2000}+ \dfrac{gz_1}{1000} )= m_2(h_2+\dfrac{v_2^2}{2000}+\dfrac{gz_2}{1000})+W_{shaft}[/tex]

Since the elevation (z) is negligible and flow via the turbine is adiabatic:

Then,

Q = 0 and z₁ = z₂

[tex]W_{shaft} = (mh_1-mh_2) + (\dfrac{mv_1^2-mv_2^2}{2000})[/tex]

[tex]W_{shaft} = ((5*3348) -(5*2550)) + (\dfrac{(5*(30)^2)-(5*(60)^2)}{2000})[/tex]

[tex]W_{shaft} = (16740-12750) + (\dfrac{4500-18000}{2000})[/tex]

[tex]W_{shaft} = (16740-12750) + (-6.75)[/tex]

[tex]W_{shaft} = 3983.25 \ kW[/tex]

[tex]\mathbf{W_{shaft} = 3.983 \ MW}[/tex]

prove that Sin^6 ϴ-cos^6ϴ=(2Sin^2ϴ-1)(cos^2ϴ+sin^4ϴ) please sove step by step with language it is opt maths question guys i willl give you 100 point and mark as brainlest answer​

Answers

By using basic trigonometric identity.....

You are given a pot of hot tea (350 mL) at a temperature of 85°C and a quantity of ice at -12°C. Determine the absolute minimum amount of ice you can add to the hot tea so that at equilibrium you have iced tea (ie. a very, very small amount of ice and some water). You can assume tea has the same density (1.00 g/mL) and specific heat (4190 J/kgK) as liquid water. The heat of fusion of H2O is 3.33x10^5 J/kg. The specific heat of ice is 2090 J/kgK.

Answers

Answer:

348 g

Explanation:

The heat gained by the ice equals the heat lost by the hot tea.

Also, since we require a very, very small amount of ice and some water, to still have some ice, the temperature of the hot tea has to decrease to the melting point of ice which is 0°C. So, the final temperature of the mixture is 0 °C.

So, mc(T - T') + mL = -MC(T - T") where m = mass of ice, c =  specific heat of ice = 2090 J/kgK., T = final temperature of mixture = 0 °C, T' = initial temperature of ice = -12 °C, L = heat of fusion of H2O = 3.33 × 10⁵ J/kg, M = mass of hot tea = ρV where ρ = density of tea = 1.00 g/mL and V = volume of hot tea = 350 mL. So, M = ρV = 1.00 g/mL × 350 mL = 350 g = 0.350 kg, C = specific heat of tea = 4190 J/kgK and T" = initial temperature of tea = 85 °C.

Making m subject of the formula, we have

mc(T - T') + mL = -MC(T - T")

m[c(T - T') + L] = -MC(T - T")  

m = -MC(T - T")/[c(T - T') + L]

substituting the values of the variables into the equation, we have

m = -MC(T - T")/[c(T - T') + L]

m = -0.350 kg × 4190 J/kgK(0 °C - 85 °C.)/[2090 J/kgK(0 °C. - (-12 °C)) + 3.33 × 10⁵ J/kg]

m = -1466.5 J/kK(- 85 °C)/[2090 J/kgK(0 °C + 12 °C)) + 3.33 × 10⁵ J/kg]

m = 124652.5 J/[2090 J/kgK(12 °C) + 3.33 × 10⁵ J/kg]

m = 124652.5 J/[25080 J/kg + 3.33 × 10⁵ J/kg]

m = 124652.5 J/358080 J/kg

m = 0.3481 kg

m = 348.1 g

m ≅ 348 g

So, the minimum amount of ice to be added is 348 g.

biến tần là gì trong công nghiệp

Answers

Nguồn điện là một yêu cầu thiết yếu của các ngành công nghiệp. Biến tần là một thiết bị độc lập có chức năng chuyển đổi điện áp một chiều thành điện áp xoay chiều. Biến tần đảm bảo rằng việc cung cấp điện không bị gián đoạn và liên tục. ... Các ngành công nghiệp yêu cầu sử dụng bộ nghịch lưu công nghiệp để hoạt động liên tục của các hoạt động trong ngành.

anxiety: a. is never normal. b. is common of many psychological disorders c. is identical to fear d. is a modern development, unlikely to have roots in human history

Answers

Answer:

B

Explanation:

Anxiety is very common especially nowadays but it's especially common in psychological disorders

Which tool is used to measure movement automotive

Answers

Answer:

Speedometer

It shows our speed, or how fast we're moving.

Uses of P-N junction

Answers

Answer:

Explanation:

Two that come to mind:

a semiconductor diode is essentially a PN junctiona transistor is made of two pn junctions.

số bit của pic 16f887

Answers

Answer:

what does it mean

Explanation:

sorry

plz write in English

an atom that gained an electron is called​

Answers

Answer:

Hey mate......

Explanation:

This is ur answer.....

When an atom gains/loses an electron, the atom becomes charged, and is called an ion.

Hope it helps!

Brainliest pls!

Follow me :)

An atom that gained an electron is called an ION.

The base of an aluminum block, which is fixed in place, measures 90 cm by 90 cm, and the height of the block is 60 cm. A force, applied to the upper face and parallel to it, produces a shear strain of 0.0060. The shear modulus of aluminum is . What is the displacement of the upper face in the direction of the applied force

Answers

The question is incomplete. The complete question is :

The base of an aluminum block, which is fixed in place, measures 90 cm by 90 cm, and the height of the block is 60 cm. A force, applied to the upper face and parallel to it, produces a shear strain of 0.0060. The shear modulus of aluminum is [tex]3.0 \times 10^{10} \ Pa[/tex] . What is the displacement of the upper face in the direction of the applied force?

Solution :

The relation between shear modulus, shear stress and strain,

[tex]$\text{Shear modulus, S =} \frac{\text{Shear stress}}{\text{shear strain}}$[/tex]

Shear stress = shear modulus (S) x shear strain

                     [tex]$=3 \times 10^{10} \times 0.0060$[/tex]

                     [tex]$=1.80 \times 10^8$[/tex] Pa

                     [tex]$=180 \times 10^6$[/tex] Pa

                     [tex]$=180 \ MPa$[/tex]

The length represents the distance between the fixed in place portion and where the force is being applied.

Therefore,

[tex]$\text{Displacement} = \text{shear strain} \times \text{length}$[/tex]

                     = 0.006 x 60 cm

                      = 0.360 cm

                      = 3.6 mm

Thus, the displacement of the upper face is 3.6 mm in the direction of the applied force.

there are many different values associated with an AC sine wave which one of the following continually changes throughout the cycle?

A. instantaneous value
b. effective value
c. peak value
d. average value​

Answers

A. The instantaneous value (of voltage for sure and also possibly of current) continually changes thought the cycle.

Sine waves are by far the most common type of alternating current waveform employed in electrical engineering. The correct option is A.

What are Sine Waves?

Sine waves are by far the most common type of alternating current waveform employed in electrical engineering. An AC Waveform is the shape formed by charting the instantaneous ordinate values of either voltage or current against time.

There are many different values associated with an AC sine wave but the one that continually changes throughout the cycle is the instantaneous value.

Hence, the correct option is A.

Learn more about Sine Wave:

https://brainly.com/question/14979785

#SPJ2

What is the following diagram called?

Answers

Answer:

flow chart

Explanation:

it's a flow chart right ? don't know the explanation cause I am not even sure I am right

Suppose we have 999 records of employees Emp1, Emp2, Emp5, Emp6 and so on up to Emp998 and Emp999 stored in a sequence. Hence, records are nothing but a row in the table. In the employee table, we want to insert new records Emp3 and Emp4 in the sequence, and once we have done insertion we need to update and retrieve the record efficiently to optimize the performance of a database by minimizing the access time when query is being executed.

Answers

The records in the table represents the employee ID of each employee. Assume the table name is EMPLOYEES and the field name of employee IDs is ID, the following SQL query inserts Emp3 and Emp4 into the employees table.

INSERT INTO EMPLOYEES (ID) values (Emp3), (Emp4)

The complete question requires that we list the pros and cons of solving the problem using Index sequential access method (ISAM).

The advantage of using ISAM is that priorities are given to the indices of the records being inserted. So, Emp3 and Emp4 will be inserted immediately after Emp2.

However, a major disadvantage of using ISAM is that it is very expensive to keep the indices in a sequential order;

See attachment for the illustration of Index sequential access method (ISAM).

Read more about Index sequential access method (ISAM) at:

https://brainly.com/question/4692093

Why is logging done during drilling?

Answers

Answer:

Logging while drilling (LWD) is a technique of conveying well logging tools into the well borehole downhole as part of the bottom hole assembly (BHA). ... In these situations, the LWD measurement ensures that some measurement of the subsurface is captured in the event that wireline operations are not possible

beacuse thye want them to hav egoood and thye wn thme tto

Answers

Answer:

I don't understand the question

I don’t understand what your asking

. Bơm kiểu piston tác dụng đơn có áp suất p=0,64 Mpa và lưu lượng Q=3,5 l/s. Xác định tốc độ quay của trục bơm và công suất của bơm nếu biết đường kính piston D=150 mm; bán kính tay quay R=60 mm; hiệu suất thể tích của bơm là 0=0,94; hiệu suất chung của bơm b=0,80.

Answers

Answer:

not understand language

A mechanic claims to have developed a car engine that runs on water instead of gasoline. What is your response to this claim?​

Answers

The claim will be impractical. The reason behind this is provided below throughout the explanation segment.

Inside the same combustion chamber, fresh water can't be pressurized even more than fuel as well as air. Consequently, the cylinder does not burn due to a problem with the compressor.To accomplish the development processes, a machine requires any sort of combustible which might cause combustion as well as create a tremendous quantity of power.

Thus, the idea of using water instead of petroleum appears unworkable throughout traditional engines.

Learn more:

https://brainly.com/question/4067583

answer this qustion plz

Answers

Answer:

click here and I'm so happy I have been doing this weekend I can see the same way you could come back in a bit and then we are all of you to know you do for a bit of time with me or

There are some sections of the SDS that are not mandatory

True or false

Answers

Answer:

True

Explanation:

There are 16 in all and 4 are not mandatory

There are some sections of the SDS that are not mandatory. Thus, option A is correct.

What is SDS?

A Safety Data Sheet, previously known as a Material Safety Data Sheet, is a thorough instructional report written by a dangerous product's producer or exporter. It gives a description of something like the product's chemical and physical characteristics.

Sections 1 through 11 and 16 must be used; sections 12 through 15 are optional but could be included. the section which will are not compulsory are:

Section 12: Environmental data

Section 13: Guidelines for Recycling

Section 14: Documentation regarding mobility

Section 15: Relevant data about regulations

In Safety Data Sheet, all the sections are not compulsory or mandatory. this statement is true. Therefore, option A is the correct option.

Learn more about Safety Data Sheet, here:

https://brainly.com/question/1442958

#SPJ2

Hydraulic fracturing is: Select one: a. a first step in storage of high-level radioactive waste b. a way of extracting natural gas shale formations c. a step in oil refining where oil is separated into different viscosities d. none of the above

Answers

The answer is B - a way of extracting natural gas shale formations.

Hydraulic fracturing is “a way of extracting natural gas shale formations.”

Shale and other types of "tight" rock, or impermeable rock formations that lock in oil and gas and complicate the production of fossil fuels, can be extracted of their natural gas or oil using the modern high-volume hydraulic fracturing process. Thus, option B is correct.

What are the factor involving in Hydraulic fracturing?

Shale gas is extracted through a procedure called hydraulic fracturing, also referred to as “fracking.” Due to the fact that shale reserves are often dispersed horizontally rather than vertically, deep holes are first drilled into the shale rock, then horizontal drilling is used to reach more of the gas.

A mixture of sand, chemicals, and water is pushed at high pressure down a borehole during hydraulic fracturing. The released gas can flow out of the rocks and back up the borehole because the water pressure causes cracks in the rock to widen, and the sand particles settle into the openings to keep them open.

Therefore, a way of extracting natural gas shale formations.

Learn more about Hydraulic fracturing here:

https://brainly.com/question/28559289

#SPJ2

which type of clectrical circuit is represented by this diagram?​

Answers

Answer:

  parallel

Explanation:

All components in this circuit are tied in parallel. Each component experiences the same voltage from one terminal to the other. It is a parallel circuit.

Troy must keep track of the amount of refrigerant he uses from a 50-pound cylinder to ensure that accurate
records are kept. He used 13 pounds on a systein for Ms. Jones and 9 pounds on a system for a commercial
client. How many pounds should he have left in the cylinder?
tof
Troy should have
pounds of refrigerant left in the cylinder.
baon naid Thamar basic
محمود احمد مجد
12
اهداء ما در

Answers

Answer:

Amount of gas still in cylinder = 28 pound

Explanation:

Given:

Amount of gas in cylinder = 50 pound

Amount of gas used in Ms. Jones system = 13 pound

Amount of gas used in client system = 9 pound

Find:

Amount of gas still in cylinder

Computation:

Amount of gas still in cylinder = Amount of gas in cylinder - Amount of gas used in Ms. Jones system - Amount of gas used in client system

Amount of gas still in cylinder = 50 - 13 - 9

Amount of gas still in cylinder = 28 pound

Other Questions
PLS HELP ME ON THIS QUESTION I WILL MARK YOU AS BRAINLIEST IF YOU KNOW THE ANSWER PLS GIVE ME A STEP BY STEP EXPLANATION!!A sample of 500 U.S. teachers are asked to express their opinions on standardized testing for their students. The population in this study is _______________.A. all U.S. studentsB. standardized testsC. all U.S. teachersD. the 500 U.S. teachers Hydrogen bromide is found in volcanic gas. What is the chemical formula forthis compound? Three is subtracted from a number, and then the difference is divided by eleven. The result is twelve. What is thenumber? The roles and responsibilities for healthcare workers and that of their department or unit can be located? Which expression is equivalent to 3/2 What is the mean of this data set? A. 84 B. 85 C. 83 D. 88 Andrew buys 27 identical small cubes, each with two adjacent faces painted red. He then uses all of these cubes to build a large cube. What is the largest number of completely red faces of the large cube that he can make HELP PLEASE ASAP!!!!! Alex can cut a cord into 7 pieces in 36 seconds. How long will it take him to cut the cord into 12 pieces? Solve for b.-32 + 10b = -22 Melting point of ice of pure water Which phrase describes a feature of groundwater? A. 4B. -9/8C. 8/7D. -7/2(its not C ik that) Why Was the constitution of the kingdom of Nepal 2015 replaced so soon? ' i promise i will mark brainliest Someone explain this I dont understand set up differential equation of angular S.H.M What is the volume of the rectangular prism? complete each sentences below with who, whom, what, whose, and wich. 1. ___ wrote on the wall? 2.with ___ did they leave? 3. ____ can you tell us about it? 4. ____ decision did you make? 5. did you tell before you told us? 6. ___ shoes are these? 7. ____ bus do you take to school? 8. ___ idea was this? 9. ___ will be able to tell us more? 5. Which pair of equations represents parallel lines?A. y =2x+7 Y=2x-7B. Y=7 X=7C. Y=2x-7 Y=-1/2-7D. Y=2x+7 Y=x+7 find the missing side of the triangle