A car generator turns at 400 rpm (revolutions per minute) when the engine is idling. It has a rectangular coil with 300 turns of dimensions 5.00 cm by 6.46 cm that rotates in an adjustable magnetic field. What is the field strength needed to produce a 24.0 V peak emf

Answers

Answer 1

Answer:

The field strength needed to produce a 24.0 V peak emf is 0.5913 T

Explanation:

From the formula for maximum emf of a generator,

[tex]emf_{max}= NAB\omega[/tex]

∴ [tex]B = \frac{emf_{max} }{NA\omega}[/tex]

Where N is the number of loops

A is cross section of loops

B is magnetic field strength

ω is the angular frequency of loops

From the question, [tex]emf_{max} = 24.0V[/tex]

N = 300 turns

A = l × b ( since it is a rectangular coil)

A = 6.46 cm × 5.00 cm

A = 0.0646 m × 0.05 m

A = 0.00323 m²

ω = 400 rpm = (400/60)×2π rad/s

ω = 41.8879 rad/s

Putting all the parameters into the formula

[tex]B = \frac{emf_{max} }{NA\omega}[/tex]

[tex]B = \frac{24.0}{300\times0.00323\times41.8879}[/tex]

[tex]B = 0.5913T[/tex]

Hence, the field strength needed to produce a 24.0 V peak emf is 0.5913 T


Related Questions

Which of the following is a vector quantity? i. Force ii. Velocity iii. Acceleration iv. All of these 5771​

Answers

All of these

Option ( iv ) is the correct answer.

Definition

A vector quantity the physical quantity that has both direction as well as magnitude.

A 2.0kg object is dropped from a height of 30m.
After it drops for 2.0 seconds, what is its kinetic
energy and what is its potential energy?
(Assume no air resistance.)

Answers

Answer:

1) The kinetic energy of the object after it drops for 2.0 seconds is approximately 384.9 Joules

2) The potential energy of the object after it drops for 2.0 seconds is approximately 204 J

Explanation:

1) The given mass of the object, m = 2.0 kg

The height from which the object is dropped, h = 30 m

The kinetic energy of the object after it drops for 2.0 seconds = Required

Kinetic energy, K.E. = (1/2)·m·v²

Where;

v = The velocity of the object

The kinematic equation for finding the velocity of the object is presented as follows;

v = u + g·t

Where;

u = The initial velocity of the object = 0

g = The acceleration due to gravity of the object ≈ 9.81 m/s²

t = The time of motion of the object = 2.0 seconds

∴ The velocity after 2 seconds, v ≈ 0 + 9.81 m/s² × 2 s = 19.62 m/s

The kinetic energy, K.E. after 2 seconds as the object drops is given as follows;

[tex]K.E._{(after \ two \ seconds)}[/tex] = (1/2) × 2.0 kg × (19.62 m/s)² = 384.9444 J ≈ 384.9 J

2) The total energy, M.E. of the object at the top, h = 30 m, u = 0, is given as follows;

The total mechanical energy, M.E. = P.E. + K.E.

M.E. = m·g·h + (1/2)·m·u²

∴ M.E. = 2.0 kg × 9.81 m/s² × 30 m + 0 = 588.6 J

M.E. = 588.6 J

Given that the total mechanical energy, M.E., is constant, we have;

At 2.0 seconds, M.E. = 588.6 J , K.E. ≈ 384.9 J, P.E. = M.E. - K.E.

∴ P.E. = 588.9 J - 384.9 J ≈ 204 J

The potential energy after it drops 2.0 seconds, P.E. ≈ 204 J

Two representative elements are in the same period of the periodic table. Which statement correctly describes the atoms of the two elements?(1 point)

They have the same number of electrons.

They have the same number of valence electrons.


They have valence electrons in different energy levels.


They have valence electrons in the same energy level.

Answers

Answer:

Elements in the same group have the same number of valence electrons.

When moving right across a period, the valence electrons of the main group elements increase by one.

When moving down a group, the valence electrons of the main group elements increase by one.

Elements in the same period have the same number of valence electrons.

Elements in the same period of the periodic table have valence electrons in the same energy levels.

When elements are in the same period on the periodic table, it means that they have the same number of shells.

The energy level of valence electrons in a atom depends on how far it is from the nucleus. This means that:

Valence electrons on elements in the same period will be the same distance from their nucleus They will have the same energy level as they are equally attracted to their nucleus

For instance, Boron, Carbon and Nitrogen will have valence electrons in the same energy levels.

In conclusion, elements in the same period will have valence electrons in the same energy levels.

Find out more at https://brainly.com/question/21367069.

An airplane starts from rest and undergoes a uniform acceleration of 10.8 m/s^2 for 16.7 s seconds before leaving the ground. What is its displacement?

Answers

Answer:

3012.012m

Explanation:

s=it +1/2(10.8)(16.7)^2

differniate between Magnetic force and electrostatic force​

Answers

Answer:

magnetic force:

i) It is exerted by a magnet.

ii)Magnetic forces are always normal to the direction of the velocity of the charge it acts upon.

Electrostatic force

i) It is exerted by electrically charged body.

ii)Electric force are independent of the direction the charge moves in.

✌✌✌✌

why does a stone sink and a ship float

Answers

Answer:

A stone is more dense than water and the air in draft of the boat is less dense than water.

Which are characteristics of a prokaryotic cell? Select three options.


O contains DNA

O lacks DNA

O contains ribosomes

O lacks ribosomes

O contains a nucleus

O lacks a nucleus

I NEED THIS QUICKLY

Answers

Answer:

A. Contains DNA

C. Contains ribosomes

F. Lacks a nucleus

Explanation:

5. Which one of the following factors is directly proportional to density of liquid? (a) Temperature (b) Volume of liquid (c) Upthrust (d) Density of object

Answers

Answer:

A

The upthrust on a floating body is in upwards direction and is equal to the weight of the liquid displaced

B

The upthrust is directly proportional to the density of the liquid in which the solid is immersed

C

The upthrust is directly proportional to the volume of the fluid displaced by a solid

The upthrust acts on the body in upward direction at the center of buoyancy.

Upthrust is equal to the weight of liquid displaced by object and weight of liquid will depend on its density.

Upthrust is F=Vρg ,where V is the volume of liquid displaced and ρ is the density of fluid.

The total lateral pressure acting on an immersed object on one side is equal and in opposite direction to the total lateral pressure acting on the other side.

A bike travels at 3.0 m/s, and then accelerates to a speed of
8.5 m/s in a time of 2.5 seconds. The average acceleration of
the bike is
m/s2

Answers

The average acceleration of the bike is 2.2 m/s²

What is average acceleration?

Acceleration, rate at which velocity changes with time, in terms of both speed and direction.

A point or an object moving in a straight line is accelerated if it speeds up or slows down.

According to the question,

Given, initial velocity, u=3.0m/s and final velocity v=8.5 m/s

Time = 2.5 seconds

If a be the acceleration.

a = [tex]\frac{v-u}{t}[/tex]

a = [tex]\frac{8.5 - 3.0}{2.5s}[/tex]

⟹ a=2.2 m/s²

So, The average acceleration of the bike is 2.2 m/s²

Learn more about average acceleration here:

https://brainly.com/question/2303856

#SPJ2

mercury is commonly used in thermometer give reasons​

Answers

Answer:

hi

BECAUSE MERCURY IS USED BECAUSE IT is the only liquid available in room temperature

Explanation:

pls mark as a BRAINLIST

Robin fired a bullet of mass 100 gm from a gun of mass 5 kg. The bullet leaves the gun with a speed of 400 m/s. After penetrating 4 cm of a plank of 10 cm, the bullet loses one third of its initial velocity.
a. Calculate the backward velocity of the gun?
b. Can the bullet penetrate the plank of the wood completely? Explain mathematically.

please help

Answers

(a) The recoil or backward velocity of the gun is 8 m/s.

(b) The bullet cannot penetrate the plank of the wood completely.

The given parameters include;

mass of the bullet, m₁ = 100 g = 0.1 kgmass of the gun, m₂ = 5 kginitial velocity of the bullet, u₁ = 400 m/sthickness of the plank, x = 10 cm

(a) The backward or recoil velocity of the gun is calculated by applying the principle of conservation of linear momentum.

let the backward or recoil  velocity of the gun = u₂

m₁u₁  + m₂u₂ = 0

m₂u₂ = -m₁u₁

[tex]u_2 = -\frac{m_1u_1}{m_2} \\\\u_2 = - \frac{0.1 \times 400}{5} \\\\u_2 = -8 \ m/s[/tex]

Thus, the recoil or backward velocity of the gun is 8 m/s.

(b) determine if the bullet can penetrate the plank of the wood completely

the bullet traveled 4 cm and lost ¹/₃ of u₁the remaining distance to completely penetrate the plank = 6 cmthe final velocity of the bullet at 4 cm, v = 400 - ¹/₃ x 400 m/s  = 266.67 m/s

the acceleration of the bullet is calculated as;

v² = u₁² + 2as

2as = v² - u²

[tex]a = \frac{v^2 -u_1^2}{2s} \\\\a = \frac{(266.67)^2 -(400)^2}{2\times 0.04} = -1.111 \times 10^6 \ m/s^2[/tex]

Finally, determine the distance traveled by the bullet when it comes to a complete stop, that is the final velocity = 0

[tex]v_f^2 = v^2 + 2ad\\\\2ad = v_f^2 - v^2\\\\d = \frac{v_f^2 - v^2}{2a} \\\\d = \frac{(0) - (266.67)^2}{2(-1.111\times 10^6)} \\\\d = 0.032 \ m[/tex]

d = 3.2 cm

The total distance traveled by the bullet inside the plank = 4 cm + 3.2 cm = 7.2 cm

Therefore, the bullet cannot penetrate the plank completely.

To learn more about linear momentum visit: https://brainly.com/question/15869303

what weight is recorded by a scale when it is placed inside a lift which is in free fall? Enplain.​

Answers

There is no pressure of your feet on the scales, and no pressure of the floor on the scales, so the scales will read zero I hope this is right

Answer:

Explanation:

There is no pressure of your feet on the scales, and no pressure of the floor on the scales, so the scales will read zero*. Hence, your weight, in a freely falling lift is zero

Muốn đun sôi 200g nước từ 30 độ cần cung cấp nhiệt lượng bao nhiêu :

Answers

Answer:

cần cung cấp 70 độ vì nước sôi ở 100°C

Explanation:

why do the other animals listen to old major speak in the barn late on night?​

Answers

https://brainly.com/question/19388823

Hope this helps!

If the force on a spring is 1 N and it stretched 0.5 m, what is the spring
constant?
A.4 N/m
B.0.2 N/m
C.2 N/m
D. 0.4 N/m

Answers

Force=F=1NStretched=x=0.5m

We know

[tex]\boxed{\sf Spring\:constant(K)=\dfrac{F}{x}}[/tex]

[tex]\\ \sf\longmapsto K=\dfrac{1}{0.5}[/tex]

[tex]\\ \sf\longmapsto K=2N/m[/tex]

A uniform, solid sphere of radius 2.50 cm and mass 4.75 kg starts with a purely translational speed of 3.00 m/s at the top of an inclined plane. The surface of the incline is 2.75 m long, and is tilted at an angle of 22.0∘ with respect to the horizontal. Assuming the sphere rolls without slipping down the incline, calculate the sphere's final translational speed v2 at the bottom of the ramp.

Answers

Answer:

The final translational seed at the bottom of the ramp is approximately 4.84 m/s

Explanation:

The given parameters are;

The radius of the sphere, R = 2.50 cm

The mass of the sphere, m = 4.75 kg

The translational speed at the top of the inclined plane, v = 3.00 m/s

The length of the inclined plane, l = 2.75 m

The angle at which the plane is tilted, θ = 22.0°

We have;

[tex]K_i[/tex] + [tex]U_i[/tex] = [tex]K_f[/tex] + [tex]U_f[/tex]

K = (1/2)×m×v²×(1 + I/(m·r²))

I = (2/5)·m·r²

K =  (1/2)×m×v²×(1 + 2/5) = 7/10 × m×v²

U = m·g·h

h = l×sin(θ)

h = 2.75×sin(22.0°)

∴ 7/10×4.75×3.00² + 4.75×9.81×2.75×sin(22.0°) = 7/10 × 4.75×[tex]v_f[/tex]² + 0

7/10×4.75×3.00² + 4.75×9.81×2.75×sin(22.0°) ≈ 77.93

∴ 77.93 ≈ 7/10 × 4.75×[tex]v_f[/tex]²

[tex]v_f[/tex]² = 77.93/(7/10 × 4.75)

[tex]v_f[/tex] ≈ √(77.93/(7/10 × 4.75)) ≈ 4.84

The final translational seed at the bottom of the ramp, [tex]v_f[/tex] ≈ 4.84 m/s.

Our Moon a. was a separate small planet before it was captured by the Earth's gravity. b. spun off the fast-spinning Earth during the early formation of the Solar System. c. coalesced from gas and dust in its current place next to the Earth. d. was formed by the collision of the Earth with a Mars-sized protoplanet.

Answers

Answer:

d. was formed by the collision of the Earth with a Mars-sized protoplanet.

According to the The giant-impact hypothesis the Moon was formed from the debris of a collision between the Earth and a Mars-sized protoplanet.

9. Which of the following is NOT a recommendation to help you succeed in this course?
Consistently and actively work in the course on a daily basis.
Wait until the end of the semester to complete all work.
Complete all assignments in a timely manner.
Contact your instructor if you have questions.

Answers

Answer:

Wait until the end of the semester to complete all work.

Explanation:

this is the obvious answer.

please mark me brainliest

Answer:

Wait until the end of the semester to complete all work

List two factors that compression force depends on ​

Answers

The magnitude (size or numerical value) and the direction.

Hope this helps!!! :)

Give reason.


b} String roller is an example of wheel and axel .Why?

Answers

Explanation:

string roller is called an example of wheel and axel because The thin rod which needs to be turned is called the axle and the wider object fixed to the axle, on which we apply force is called the wheel.

hence the we apply force on the roller and the string gets tight.

what give negative acceleration ?

Answers

Answer:

But negative acceleration means that the rate of change of velocity is negative or velocity decreases. Example: (1) When we apply brakes in a moving car, then negative acceleration acts on it and the car stops. (2) When we throw a ball upwards, then also negative acceleration acts on it.

Explanation:

If it helps you mark me as a brainleast

MATHEMATICALLY A NEGATIVE ACCELERATION MEANS YOU WILL SUBTRACT FROM THE CURRENT VALUE OF THE VELOCITY.

Is velocity ratio of a machine affected by applying oil on it? Explain with reasons.

Answers

Answer:

when it comes to machines being Rusty oil is like the root loosener

A force of 150N at an angle of 60 degree to the horizontal to pull a box through a distance of 50m calculate the work done

Answers

Force=150NAngle=60°Displacement=50m

[tex]\boxed{\sf W=Fscos\Theta}[/tex]

[tex]\\ \sf\longmapsto W=150(50)cos 60[/tex]

[tex]\\ \sf\longmapsto W=7500\times \dfrac{1}{2}[/tex]

[tex]\\ \sf\longmapsto W=3750J[/tex]

a car moves at a speed of 40km/h. it is stopped by applying brake which produce a uniform acceleration of-0.5m/s^2. how much distance will it move before coming to stop ?

Answers

Answer:

Explanation:

We first need to convert the 40 km/h to m/s. Going by the fact that 40 has only 1 significant figure in it, 40 km/h = 10 m/s. The rest of the values are in their proper labels. We will use the equation:

[tex]v^2=v_0^2+2a[/tex]Δx where the final velocity is 0 because the car is coming to a stop at the end; the initial velocity is 10 m/s, the acceleration (or, rather, deceleration) is -.5 m/s/s, and our unknown which is displacement. Filling in:

[tex]0=(10)^2+2(-.5)[/tex]Δx and solving for Δx:

Δx = [tex]\frac{-100}{2(-.5)}[/tex] which ends up being simply that

Δx = 100 m

Give reason Pascal is a derived unit​

Answers

Answer:

Pascal is a derived unit because it cannot be expressed in any physics terms, but it is an expression of fundamental quantities.

Explanation:

[tex]{ \sf{Pasacal \: ( Pa) = \frac{newtons}{metres {}^{2} } }} \\ \\ { \sf{Pasacal \: (Pa) = \frac{kg \times {ms}^{ - 2} }{ {m}^{2} } }}[/tex]

A car horn creates a 595 Hz tone at rest. Two cars pass on the street, each going 20.0 m/s; the first car honks. What frequency does the other car hear before they pass each other?

Answers

Doppler frequency, the other car hear before they pass each other is 668.68 Hz.

What is frequency?

Frequency is the number of occurrences of a repeating event per unit of time.

What is Doppler EFFECT?

The Doppler effect is the change in frequency of a wave in relation to an observer who is moving relative to the wave source.

According to the Doppler Effect, the frequency observed is

  [tex]fo=fs\frac{v+v_{o} }{v-v_{s} }[/tex]

[tex]f_{o}=595\frac{343+20 }{343-20 }\\f_{o} = 668.68 Hz[/tex]

To know more about Doppler Effect here

https://brainly.com/question/15318474

#SPJ2

why does balloon pop in the sun? ​

Answers

Answer:

The heat gives atoms/ particles in balloon more kinetic energy so they move further apart, increasing size and eventually popping balloon

^ very simple explanation

Explanation:

The direction of applied force has to be .............. to the distance in order to say work is done​

Answers

Answer:

Parallel

Explanation:

The work done is defined as the force applied on an object and the displacement in the position of the object in the direction of force.

W = F s cos A

where, F is the force, s is the displacement and A is the angle between force and displacement.

When the angle between the force and the displacement is 90 degree, the work done is zero.

To get the maximum work the angle between the force and the displacement is 0 degree.

So, to get the work done by the force the angle between the force and displacement is 0 degree that means the force and displacement is parallel to each other.

difference between uniform motion and non uniform motion

Answers

Answer:

Uniform motion is a type of motion that is characterized as the motion of an object wherein the object moves in a straight line and its velocity remains unchanged along that line, regardless of the duration of time, as it occupies equal distances at equal time interval and Non-uniform motion is described as the motion of an object wherein the object moves at different speeds and does not cover the same distance at equal time intervals, regardless of the duration of the time interval.

Answer:

hope it's help you

Explanation:

In Uniform motion, the movement of a body is along the straight line with constant speed. In non uniform motion, the movement of a body is along the straight line with variable speed. In uniform motion, the body covers equal distance in an equal interval of time.

is there any machine that is 100% efficient? why?why not

Answers

Answer:

No, it's not there.

Explanation:

For a machine to be 100% efficient, it has to be with an output which is equal to its input. But machines have an out put less than an input, hence efficiency below 100%.

Other Questions
Please help me to find this answer which one is more powerful hydrogen bomb or atom bomb and why? mary wear a new hat when suddenly the wind blow it away(using the correct form of verb) during a journey, a car travels at 40 km in 2.5 hours, next 62 km in 3 hours, then took a break for 30 minutes, again travelled the last 120 km in 3.2 hours. calculate the average speed of the car during the journey. Ponzi Products produced 100 chain-letter kits this quarter, resulting in a total cash outlay of $10 per unit. It will sell 50 of the kits next quarter at a price of $11, and the other 50 kits in the third quarter at a price of $12. It takes a full quarter for Ponzi to collect its bills from its customers. (Ignore possible sales in earlier or later quarters.)a. What is the net income for Ponzi next quarter?b. What are the cash flows for the company this quarter?c. What are the cash flows for the company in the third quarter?d. What is Ponzis net working capital in the next quarter? Please show your work[tex]1\frac{2}{3} + 2\frac{3}{4}[/tex] Oxide of nitrogen that is acidic simplify (4+3)(4-3) hello guys, Define wave length.I think this will be easy for u guys good day thank u Which species of gymnosperms has reddish cones and strap like leaves that tear up from the harsh desert conditions?A. gnetumB. welwitschiaC. ephedra Using the graph, determine the equation of the axis of symmetry. (-2x) (x-3) answer please Which organ system in the human body is responsible for the transportation of nutrients, gases, wastes and blood?a) cardiovascular system b) respiratory system c) excretory system d) immune system Which of the following are valid probability distributions? Mill Co. uses a batch processing method to process its sales transactions. Data on Mill's sales transaction tape are electronically sorted by customer number and are subjected to programmed edit checks in preparing its invoices, sales journals, and updated customer account balances. One of the direct outputs of the creation of this tape most likely would be a It is Kekes birthday, and her parents want to surprise her with a room full of balloons. Use the Fermi processto estimate the number of balloons needed to fill Kekes living room. Assume the living room is a rectangularprism with a length of 30 feet, a width of 45 feet, and a height of 11 feet. Assume the balloons are sphereswith a radius of 0.45 feet. Show your work logical fallacy Well, what form of government do you want, a government by liberal do-gooders ready to spend your hard-earned dollars or a government led by business minds that understand how to live within a tight budget and generate jobs that put people to work. Group of answer choices calculate the speed, in ms- of vehicle A and of vehicle B Which of the following substances can be used to neutralize HF?A: HFB: SO2C: HCID: NaOH True or False.Section 1981 provides similar relief to an aggrieved employee as Title VII.