(20 points) (Assessment of Outcome 1): A plant has two identical standby generator units for emergency use. In the area of the generators, the normal noise level registers 82 dBA on the sound-level meter with the generators turned off. When one generator switches on, the SLM needle jumps to 85.8 dBA. What will the dBA reading be when the second generator also turns on (so that both generators are on)

Answers

Answer 1

Answer:

It wouldn't get any louder then maybe 3db more

Explanation:

There's even a equation if you wanted to check this out but, if they are the same generator same model and all and made the same precise noise it wouldn't increase more then 3db.


Related Questions

is sampled at a rate of to produce the sampled vector and then quantized. Assume, as usual, the minimum voltage of the dynamic range is represented by all zeros and the maximum value with all ones. The numbers should increase in binary order from bottom to top. Find the bit combination used to store each sample when rounded to the nearest integer between and (clipping may occur). Note: A partially-correct answer will not be recognized. You must answer all three correctly on the same

Answers

Answer:

d[0] = 11111111

d[1] = 11011101

d[2] = 1111011

Explanation:

Assume that the number of bits is 8. The voltage range input is -8 to 7 volts. The range is thus 15V, and the resolution is 15/2^8 = 0.0586 volts. We will first add +8 to the input to convert it to a 0-15v signal. Then find the equivalent bit representation. For 7.8 volts, the binary signal will be all 1's, since the max input voltage for the ADC is 7 volts. For 4.95, we have 4.95+8 = 12.95 volts. Thus, N = 12.95/0.0586 = 221. The binary representation is 11011101. For -0.8, we have -0.8 + 8 = 7.2. Thus, N = 7.2/0.0586 = 123. The binary representation is 1111011.

Thus,

d[0] = 11111111

d[1] = 11011101

d[2] = 1111011

An air conditioning unit is used to provide cooling during summer for a house. If the air conditioner provides 450 kW cooling by using 150 kW electrical power, determine the coefficient of performance (COP) of the air conditioner. The outside temperature and inside temperature are 40 and 20°C, respectively. Using the inequality of Clausius determine if the cycle is possible. Determine the COP of an air conditioner working based on the Carnot cycle between the same temperature difference. Compare the COPs of the Carnot and actual air conditioners and comment on them based on your answer for the previous part (the inequality of

Answers

Answer:

See explaination

Explanation:

Please kindly check attachment for the step by step solution of the given problem.

Two Electric field vectors E1 and E2 are perpendicular to each other; obtain its base
vectors.

Answers

Answer:

<E1, E2>.

Explanation:

So, in the question above we are given that the Two Electric field vectors E1 and E2 are perpendicular to each other. Thus, we are going to have the i and the j components for the two Electric Field that is E1 and E2 respectively. That is to say the addition we give us a resultant E which is an arbitrary vector;

E = |E| cos θi + |E| sin θj. -------------------(1).

Therefore, if we make use of the components division rule we will have something like what we have below;

x = |E2|/ |E| cos θ and y = |E1|/|E| sin θ

Therefore, we will now have;

E = x |E2| i + y |E1| j.

The base vectors is then Given as <E1, E2>.

Find a negative feedback controller with at least two tunable gains that (1) results in zero steady state error when the input is a unit step (1/s). (and show why it works); (2) Gives a settling time of 4 seconds; (3) has 10% overshoot. Use the standard 2nd order approximation. Plot the step response of the system and compare the standard approximation with the plot.

Answers

Answer:

Gc(s) = [tex]\frac{0.1s + 0.28727}{s}[/tex]

Explanation:

comparing the standard approximation with the plot attached we can tune the PI gains so that the desired response is obtained. this is because the time requirement of the setting is met while the %OS requirement is not achieved instead a 12% OS is seen from the plot.

attached is the detailed solution and the plot in Matlab

The supplement file* that enclosed to this homework consists Time Versus Force data. The first column in the file stands for time (second) and the 2nd stands for force (Volt), respectively. This data were retrieved during an impact event. In this test, an impactor strikes to a sample. A force-ring sensor that attached to the impactor generates voltage during collision. A data acquisition card gathers the generated signals.
• Take the mass of the impactor as 30 kg and strike velocity as 2.0 m/s.
• Pick the best numerical technique, justify your choice.
• All results must be in SI units.

a) Determine a factor that will be used in the conversion from V to N. The calibration data that supplied by manufacturer as below:
• Take the mass of the impactor as 30 kg and strike velocity as 2.0 m/s.
• Pick the best numerical technique, justify your choice.
• All results must be in SI units.

a) Determine a factor that will be used in the conversion from V to N. The calibration data that supplied by manufacturer as below:• Take the mass of the impactor as 30 kg and strike velocity as 2.0 m/s.
• Pick the best numerical technique, justify your choice.
• All results must be in SI units.

a) Determine a factor that will be used in the conversion from V to N. The calibration data that supplied by manufacturer as below:
b) Compute the impulse of this event.
c) Obtain acceleration, velocity and displacement histories by using Newton’s second law of motion.
d) Compute the absorbed energy during collision.

Answers

Answer:

A.) 1mv = 2000N

B.) Impulse = 60Ns

C.) Acceleration = 66.67 m/s^2

Velocity = 4 m/s

Displacement = 0.075 metre

Absorbed energy = 60 J

Explanation:

A.) Using a mathematical linear equation,

Y = MX + C

Where M = (2000 - 0)/( 898 - 0 )

M = 2000/898

M = 2.23

Let Y = 2000 and X = 898

2000 = 2.23(898) + C

2000 = 2000 + C

C = 0

We can therefore conclude that

1 mV = 2000N

B.) Impulse is the product of force and time.

Also, impulse = momentum

Given that

Mass M = 30kg

Velocity V = 2 m/s

Impulse = M × V = momentum

Impulse = 30 × 2 = 60 Ns

C.) Force = mass × acceleration

F = ma

Substitute force and mass into the formula

2000 = 30a

Make a the subject of formula

a = 2000/30

acceleration a = 66.67 m/s^2

Since impulse = 60 Ns

From Newton 2nd law,

Force = rate of change in momentum

Where

change in momentum = -MV - (- MU)

Impulse = -MV + MU

Where U = initial velocity

60 = -60 + MU

30U = 120

U = 120/30

U = 4 m/s

Force = 2000N

Impulse = Ft

Substitute force and impulse to get time

60 = 2000t

t = 60/2000

t = 0.03 second

Using third equation of motion

V^2 = U^2 + 2as

Where S = displacement

4^2 = 2^2 + 2 × 66.67S

16 = 4 + 133.4S

133.4S = 10

S = 10/133.4

S = 0.075 metre

D.) Energy = 1/2 mV^2

Energy = 0.5 × 30 × 2^2

Energy = 15 × 4 = 60J

Sludge wasting rate (Qw) from the solids residence time (Thetac = mcrt) calculation. Given the following information from the previous problem. The total design flow is 15,000 m3/day. Theoretical hydraulic detention time (Theta) = 8 hours. The NPDES limit is 25 mg/L BOD/30 mg/L TSS.

Assume that the waste strength is 170 mg/L BOD after primary clarification.

XA=MLSS = 2200 mg/L,
Xw = Xu = XR = 6,600 mg/L,
qc = 8 days.

Make sure you account for the solids in the discharge.

What volume of sludge (Qw=m3/day) is wasted each day from the secondary clarifiers?

Answers

Answer:

The volume of sludge wasted each day from the secondary classifiers is Qw = 208.33 m^3 / day

Explanation:

Check the file attached for a complete solution.

The volume of the aeration tank was first calculated, V = 5000 m^3 / day.

The value of V was consequently substituted into the formula for the wasted sludge flow. The value of the wasted sludge flow was calculated to be Qw = 208.33 m^3 / day.

6. For the following waste treatment facility, chemical concentration (mg/gal) within the tank can be considered uniform. The initial chemical concentration inside the tank was 5 mg/gal, the concentration of effluent coming in is 20 mg/gal. The volume of the tank is 600 gallons. The fluid coming in rate is equal to fluid going out is equal to 60 gal/min. (a) Establish a dynamic model of how the concentration of chemical inside the tank increases over time. Specify the units for your variables. (Hint: establish a mass balance of the waste chemical. The concentration inside the tank = concentration going out) (b) Find the Laplace transformation of the concentration (transfer function) for this step input of 20 mg/gal.

Answers

Answer:

mass of chemical coming in per minute = 60 × 20 = 1200 mg/min

at a time t(min) , M = mass of chemical = 1200 × t mg

concentration of chemical = 1200t / 600 = 2t mg / gallon

Explanation:

Since it is only fluid that is leaving and not chemical.

How does a car batteray NOT die?

Answers

Answer:

bye hooking plugs up to it to amp it up

Problem Statement: Air flows at a rate of 0.1 kg/s through a device as shown below. The pressure and temperature of the air at location 1 are 0.2 MPa and 800 K and at location 2 the pressure and temperature are 0.75 MPa and 700 K. The surroundings are at 300 K and the surface temperature of the device is 1000 K. Determine the rate that the device performs work on its surroundings if the rate of heat transfer from the surface of the device to the environment is 1 kW. Justify your answer. Note that the flow direction for the air is not specified so you need to consider all possibilities for the direction of the airflow. Assume that the air is an ideal gas, that R

Answers

Answer:

The answer is "+9.05 kw"

Explanation:

In the given question some information is missing which can be given in the following attachment.

The solution to this question can be defined as follows:

let assume that flow is from 1 to 2 then

Q= 1kw

m=0.1 kg/s

From the steady flow energy equation is:

[tex]m\{n_1+ \frac{v^2_1}{z}+ gz_1 \}+Q= m \{h_2+ \frac{v^2_2}{2}+ gz_2\}+w\\\\\ change \ energy\\\\0.1[1.005 \times 800]-1= 0.01[1.005\times 700]+w\\\\w= +9.05 \ kw\\\\[/tex]

If the sign of the work performed is positive, it means the work is done on the surrounding so, that the expected direction of the flow is right.

what is the Economic​

Answers

Economics is the social science that studies the production, distribution, and consumption of goods and services. Economics focuses on the behaviour and interactions of economic agents and how economies work-...........did this help

Design a circuit that will tell whether a given month has 31 days in it. The month is specified by a 4-bit input, A3:0. For example, if the inputs are 0001, the month is January, and if the inputs are 1100, the month is December. The circuit output, Y, should be HIGH only when the month specified by the inputs has 31 days in it. However, if the input is not a valid month (such as 0 or 13) then the output is don’t care (can be either 0 or 1).

Answers

Answer:

  see attachments

Explanation:

A Karnaugh map for the output is shown in the first attachment. The labeled and shaded squares represent the cases where Y = HIGH. The associated logic can be simplified to

  Y = A3 xor A0

when the don't care at 1110 gives an output of HIGH.

__

The second attachment shows a logic diagram using a 4:1 multiplexer to do the decoding. A simple XOR gate would serve as well. If AND-OR-INV logic is required, that would be ...

  Y = Or(And(A3, Inv(A0)), And(A0, Inv(A3)))

The asymmetric roof truss is of the type used when a near normal angle of incidence of sunlight onto the south-facing surface ABC is desirable for solar energy purposes. The five vertical loads represent the effect of the weights of the truss and supported roofing materials. The 390-N load represents the effect of wind pressure. Determine the equivalent force-couple system at A. The couple is positive if counterclockwise, negative if clockwise. Also, compute the x-intercept of the line of action of the system resultant treated as a single force R.

Answers

Answer:

[tex]R= 337.75\ \bar i - 2275 \ \bar j \ \ N[/tex]

[tex]\sum M_A = -13650 \ N.m[/tex]

x = 6 m

Explanation:

From the diagram attached below :

Equivalent force:

[tex]R= -260 \bar j + 390 \ cos 30 \bar{ i} - 390 \ sin 30 \bar j - 520 \ \bar j- 520 \ \bar j- 520 \ \bar j- 260 \ \bar j[/tex]

[tex]R= 337.75\ \bar i - 2275 \ \bar j \ \ N[/tex]

The equivalent couple at point A is as follows:

[tex]\sum M_A = -390(3)-520(\frac{6}{2})- 520({6})- 520(6+\frac{6}{2}) -260(12)[/tex]

[tex]\sum M_A = -13650 \ N.m[/tex]

By applying the principles of momentum :

[tex]\sum M_A = Ry(x)[/tex]

[tex]- 13650 = - 2275 \ x[/tex]

x = [tex]\frac{13650}{2275}[/tex]

x = 6 m

A thin‐walled tube with a diameter of 12 mm and length of 25 m is used to carry exhaust gas from a smoke stack to the laboratory in a nearby building for analysis. The gas enters the tube at 200°C and with a mass flow rate of 0.006 kg/s. Autumn winds at a temperature of 15°C blow directly across the tube at a velocity of 2.5 m/s. Assume the thermophysical properties of the exhaust gas are those of air

Estimate the average heat transfer coefficient for the exhaust gas flowing inside the tube.

Answers

Answer:

The average heat transfer coefficient for the exhaust gas flowing inside the tube, h = 204.41 W/m^2 - K

Explanation:

The detailed solution is attached as files below.

However, the steps followed are highlighted:

1) The average temperature was calculated as 380.5 K

2) The properties of air at 380.5 K was highlighted

3) The Prandti number was calculated. Pr = 0.693

4) The Reynold number was calculated, Re = 28716.77

5) The Nusselt umber was calculated, Nu = 75.94

6) From Nu = (hD)/k , the average heat transfer coefficient, h, was calculated and a value of 204.41 W/m^2 - K was gotten.

A flat site is being considered for a new school that will have a steel frame and brick façade. The steel columns will have a maximum load of 250 kips, and the planned column support will consist of a 6 foot by 6 foot square footing placed 2 feet below the ground surface (to the bottom of the footing). Subsurface conditions consist of a 15-foot-thick layer of uniform silty sand (unit weight = 122 pcf, soil modulus = 160,000 psf) over stiff clay (unit weight = 118 pcf, soil modulus = 230,000 psf). Groundwater is deep.
a) Sketch the problem (freehand, not to scale) and state any necessary assumptions.
b) Calculate the immediate (elastic) settlement.

Answers

Answer:

See explaination

Explanation:

Please kindly check attachment for the step by step solution of the given problem

For an Ac signal with peak voltage Vp equal to 60V, the same power would be delivered to a load with a dc voltage of

Answers

Answer:

  30√2 ≈ 42.426 volts

Explanation:

The RMS value of the signal is the DC equivalent. For a sine wave, the mean of the square is half the square of the peak value. Then the Root-Mean-Square is ...

  RMS = √((Vp)^2/2) = Vp/√2

For Vp = 60 volts, the equivalent DC voltage is ...

  V = (60 volts)/√2 = 30√2 volts ≈ 42.426 volts

Air at 100°F, 1 atm, and 10% relative humidity enters an evaporative cooler operating at steady state. The volumetric flow rate of the incoming air is 1765 ft3/min. Liquid water at 68°F enters the cooler and fully evaporates. Moist air exits the cooler at 70°F, 1 atm. There is no significant heat transfer between the device and its surroundings and kinetic and potential energy effects can be neglected. Determine the mass flow rate at which liquid enters, in lb(water)/min.

Answers

Answer:

Check the explanation

Explanation:

Kindly check the attached image below to see the step by step explanation to the question above.

An insulated, vertical piston–cylinder device initially contains 10 kg of water, 6 kg of which is in the vapor phase. The mass of the piston is such that it maintains a constant pressure of 200 kPa inside the cylinder. Now steam at 0.5 MPa and 350°C is allowed to enter the cylinder from a supply line until all the liquid in the cylinder has vaporized. Determine (a) the final temperature in the cylinder and (b) the mass of the steam that has entered.

Answers

Answer:

See explaination

Explanation:

Please kindly check attachment for the step by step solution of the given problem.

Have you ever had an ice cream headache that’s when a painful sensation resonates in your head after eating something cold usually ice cream on a hot day this pain is produced by the dilation of a nerve center in the roof of your mouth the nerve center is overreacting to the cold by trying to hit your brain ice cream headaches have turned many smiles to frowns identify the structure

Answers

Answer:

Cause and effect

Explanation:

pls mark brainliest

The  structure that makes or turned many smiles to frowns can be regarded as compare/contrast.

What is compare contrast?

The term compare/contrast  is a common terms. The act of comparing is known to be depicting the similarities, and contrasting is said to be showing differences that exist between two things.

Conclusively, from the above, we can see that it is a compare/contrast scenario as it talks about the effects of taking ice cream. It went from  smiles to frowns.

See option below

cause/effect

descriptive

compare/contrast

sequence/process

Learn more about compare/contrast from

https://brainly.com/question/9087023

Consider this example of a recurrence relation. A police officer needs to patrol a gated community. He would like to enter the gate, cruise all the streets exactly once, and then leave by the same gate. What information would you need to determine a Euler circuit and a Hamilton circuit

Answers

Answer:

the police officer cruise each streets precisely once and he enters and exit with the same gate.

Explanation:

NB: kindly check below for the attached picture.

The term ''Euler circuit'' can simply be defined as the graph that shows the edge of K once in a finite way by starting and putting a stop to it at the same vertex.

The term "Hamiltonian Circuit" is also known as the Hamiltonian cycle which is all about a one time visit to the vertex.

Here in this question, the door is the vertex and the road is the edge.

The information needed to detemine a Euler circuit and a Hamilton circuit is;

"the police officer cruise each streets precisely once and he enters and exit with the same gate."

Check attachment for each type of circuit and the differences.

the police officer cruise each streets precisely once and he enters and exit with the same gate.

A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has inner and outer diameters of 24 and 30 mm and is connected by eight struts to an insulated outer tube of 60-mm diameter. Each strut is 3 mm thick and is integrally fabricated with the inner tube from carbon steel (k 50 W/m K). Consider conditions for which water at 300 K flows through the inner tube at 0.161 kg/s while flue gases at 800 K flow through the annulus, maintaining a convection coefficient of 100 W/m2 K on both the struts and the outer surface of the inner tube. What is the rate of heat transfer per unit length of tube from gas to the water?

Answers

Answer:

See explaination

Explanation:

Please kindly check attachment for the step by step solution of the given problem.

Create an abstract class DiscountPolicy. It should have a single abstract method computeDiscount that will return the discount for the purchase of a given number of a single item. The method has two parameters, count and itemCost. 2. Derive a class BulkDiscount from DiscountPolicy, as described in the previous exercise. It should have a constructor that has two parameters, minimum and percent. It should define the method computeDiscount so that if the quantity purchased of an item is more than minimum, the discount is percent percent. 3. Derive a class BuyNItemsGetOneFree from DiscountPolicy, as described in Exercise 1. The class should have a constructor that has a single parameter n. In addition, the class should define the method computeDiscount so that every nth item is free. For example, the following table gives the discount for the purchase of various counts of an item that costs $10, when n is 3: count 1 2 3 4 5 6 7 Discount 0 0 10 10 10 20 20

4. Derive a class CombinedDiscount from DiscountPolicy, as described in Exercise 1. It should have a constructor that has two parameters of type DiscountPolicy. It should define the method computeDiscount to return the maximum value returned by computeDiscount for each of its two private discount policies. The two discount policies are described in Exercises 2 and 3. 5. Define DiscountPolicy as an interface instead of the abstract class described in Exercise 1.

Answers

Answer:

Java Code was used to define classes in the abstract discount policy,The bulk discount, The buy items get one free and the combined discount

Explanation:

Solution

Code:

Main.java

public class Main {

public static void main(String[] args) {

  BulkDiscount bd=new BulkDiscount(10,5);

BuyNItemsGetOneFree bnd=new BuyNItemsGetOneFree(5);

CombinedDiscount cd=new CombinedDiscount(bd,bnd);

System.out.println("Bulk Discount :"+bd.computeDiscount(20, 20));

  System.out.println("Nth item discount :"+bnd.computeDiscount(20, 20));

 System.out.println("Combined discount :"+cd.computeDiscount(20, 20));    

  }

}

discountPolicy.java

public abstract class DiscountPolicy

{    

public abstract double computeDiscount(int count, double itemCost);

}    

BulkDiscount.java  

public class BulkDiscount extends DiscountPolicy

{    

private double percent;

private double minimum;

public BulkDiscount(int minimum, double percent)

{

this.minimum = minimum;

this.percent = percent;

}

at Override

public double computeDiscount(int count, double itemCost)

{

if (count >= minimum)

{

return (percent/100)*(count*itemCost); //discount is total price * percentage discount

}

return 0;

}

}

BuyNItemsGetOneFree.java

public class BuyNItemsGetOneFree extends DiscountPolicy

{

private int itemNumberForFree;

public BuyNItemsGetOneFree(int n)

{

  itemNumberForFree = n;

}

at Override

public double computeDiscount(int count, double itemCost)

{

if(count > itemNumberForFree)

return (count/itemNumberForFree)*itemCost;

else

  return 0;

}

}

CombinedDiscount.java

public class CombinedDiscount extends DiscountPolicy

{

private DiscountPolicy first, second;

public CombinedDiscount(DiscountPolicy firstDiscount, DiscountPolicy secondDiscount)

{

first = firstDiscount;

second = secondDiscount;

}

at Override

public double computeDiscount(int count, double itemCost)

{

double firstDiscount=first.computeDiscount(count, itemCost);

double secondDiscount=second.computeDiscount(count, itemCost);

if(firstDiscount>secondDiscount){

  return firstDiscount;

}else{

  return secondDiscount;

}

}  

}

(USCS units) A deep drawing operation is performed on a sheet-metal blank that is 1/8 in thick. The height of the cup = 3.8 in and its diameter = 5.0 in (both inside dimensions).

(a) Assuming the punch radius = 0, compute the starting diameter of the blank to complete the operation with no material left in the flange.

(b) Is the operation feasible (ignoring the fact that the punch radius is too small)?

Answers

Answer:

See explaination

Explanation:

Please kindly check attachment for the step by step solution of the given problem

Other Questions
Three people hiked the same 1 mile trail. The distance for each hiker is reperesented in the drawing. Show about where the 1 mile mark should be on each drawing.Explain Which is not a reason that water is used to store spent fuel rods from nuclear power plants? Water increases the speed of the chain reaction in the fuel rods. Water protects nuclear power plant workers from the high temperature and radiation of the fuel rods. Water acts as a radiation shield to reduce the radiation levels. Water cools the spent rods. Wanda did 12 push-ups on Saturday, 24 push-ups on Sunday, 48 push-ups on Monday, and96 push-ups on Tuesday. What kind of sequence is this? Please dont comment if you dont know the answer. So I have an hp laptop that I have a year with and everything was working great until a month ago when it started saying that the battery couldnt hold charge anymore. Since I didnt want to buy a battery I simply started using while connected with the charger. But after a few days of saying the battery couldnt hold charge out of a sudden when I tried connecting my mouse or controller it would recognized. It passed power to whatever I connected to it but it simply wouldnt work. Can it be fixed? Or do I have to buy a new one. how kepler describe the planets orbits Je me suis cass le bras quand je faisais du ski. Le mdecin ma donc prscrit dix sessions de _________________.A. poche de glaceB. kinsithrapieC. pltreD. chirurgie Which of the following is true?A. South Vietnam surrendered on April 30, 1975, as Northern troops entered Saigon. B.Vietnam was officially reunited on July 2, 1976.C. The country became the Socialist Republic of Vietnam, with its capital at Hanoi. D. All of the above When historians use the term "___ ___" they are referring to the United States during the Civil War, and when they use the term "The Confederacy" they're talking about the Confederate States of America. 20 POINTS!!!!!!!!!!!!!!!!!!!!!!!!!!!!How many 4-digit multiples of 5 are there?please have a formula and don't just write them all out. Thanks. You are making pudding. The recipe asks for 3/10 cup of sugar and you want to make 8/2 of the original recipe. How many cups of sugar will you need? Giving Brainliest if correct!!Rihanna wants to purchase a dishwasher and is shopping around at different stores. Which two benefits can Rihanna get from using credit instead of cash for her purchase?(You can pick more than 1)1. She can receive a discount on the price if she uses credit instead of paying cash2. She can use the dishwasher while paying for it over a period of time.3. Her cost of purchase will decrease if she uses credit instead of cash4. She can buy the dishwasher even if she doesnt have the money now to pay for it.5. She wont need to pay taxes on the purchase. Cattle live in an area where the streams are dry. For which basic need do these cattle most likely compete? a food b shelter c water d energy YOU WILL GET BRAINLIEST!! What could help a country move from Stage 1 to Stage 2 of the demographictransition?- Instituting population restrictions-increased immigration-The diffusion of contraceptives-better sanitation-Improving education for women Arrasmith Corporation uses customers served as its measure of activity. During February, the company budgeted for 37,000 customers, but actually served 27,000 customers. The company uses the following revenue and cost formulas in its budgeting, where q is the number of customers served: Revenue: $5.50q Wages and salaries: $35,200 + $1.70q Supplies: $1.10q Insurance: $12,400 Miscellaneous expenses: $8,400 + $0.50q The company reported the following actual results for February: Revenue $ 159,800 Wages and salaries $ 70,000 Supplies $ 16,400 Insurance $ 12,400 Miscellaneous expense $ 27,700 Required: Prepare the company's flexible budget performance report for February. Label each variance as favorable (F) or unfavorable (U). (Indicate the effect of each variance by selecting "F" for favorable, "U" for unfavorable, and "None" for no effect (i.e., zero variance). Input all amounts as positive values.) the table shows jills math quiz scores. what is the minimum score she needs on her next quiz to have a mean of at least 92week 1: 92week 2: 96week 3: 94week 4: 88 Mills Corporation's balance sheet included the following information: Accounts Receivable $ 580,000 Less: Allowance for Doubtful Accounts 73,000 Accounts Receivable, Net of Allowance $ 507,000 If the Allowance account had a credit balance of $31,500 immediately before the year-end adjustment for bad debts and no accounts were written-off or allowed for during the year, what was the amount of Bad Debt Expense recognized during the year Fifteen mothers were asked how many months old their babies were when they cut their first tooth. The results are shown below.8, 8, 6, 8, 9, 10, 5, 7, 9, 5, 9, 7, 6, 8, 7Find the range and the outlier(s), if any, of the data set. Select all the following that describe isotopes of an element_ Different numbers of neutrons_ Different mass numbers_ Different atomic numbers_ Different numbers of protons Need help with Spanish! Math question down below