Which of the following statements is true about the relationship between the two forms of Newton's second law (Fnet = dp/dt and Fnet = m.a) Select the correct answer
a. Fnet = dp/dt reduces to Fnet = m.a if the O acceleration of the object does not change with time. b. Fnet = m.a reduces to Fnet = dp/dt if the acceleration of the object does not change with time. c. Fnet = m.a reduces to Fnet = dp/dt if the mass of the object Answer dt does not change with time. d. Fnet = m.a reduces to Fnet = m.a if the dt momentum of the object does not change with time. e. Fnet = dp/dt reduces to Fnet = m.a if the mass of the object does not change with time. f. Fnet = m.a reduces to Fnet = dp/dt if the momentum of the object does not change with time.

In this case, the roller coaster starts with kinetic energy because it has an initial speed of 5 m/s.

Since the roller coaster's total energy is conserved throughout the ride, its final speed when it reaches the bottom will be the same as its initial speed of 5 m/s.

As it goes uphill, the kinetic energy is gradually converted into potential energy, so its speed decreases until it reaches the top, where it has only potential energy. When it stops, all the kinetic energy has been converted to potential energy. As the roller coaster rolls back down, the potential energy is converted back to kinetic energy, and its speed increases until it reaches the bottom, where all the potential energy has been converted back to kinetic energy.

This is because the roller coaster's potential energy at the top is equal to the sum of its initial kinetic energy and the work done by gravity as it went uphill. The roller coaster then converts all of its potential energy back into kinetic energy as it rolls back down the hill.

For more similar questions on conservation of energy and physics:

brainly.com/question/381281

#SPJ11

The required mass of the cube when width of the cube and density of the cube are specified is calculated to be 0.0502 kg.

The width of the cube is given as 18.45 mm = 18.45 × 10⁻³ m

The density of the cube is given as 8 × 10³ kg/m³.

Mass of the cube is to be found out.

The general formula for density of a cube is given by, V = s³

where,

V is volume

s is side/width/height (As they are all equal in a cube)

So, the volume of the cube is,

V = (18.45 × 10⁻³)³ = 0.01845³ = 6.28 × 10⁻⁶ m³

Now, we know the general equation for density as, mass upon unit volume.

Mathematically, D = m/V

Making m as subject, we have,

Mass m = D × V = 8 × 10³ × 6.28 × 10⁻⁶ = 50.24× 10⁻³ kg = 0.0502 kg

Thus, the required mass is calculated to be 0.0502 kg.

To know more about density:

https://brainly.com/question/952755

#SPJ4

The change in enthalpy of an incompressible substance with a density of 1000 kg/m³ that is isothermally compressed from 100 to 1000 kPa is 0 kJ/kg.

Enthalpy is a measure of the total energy of a thermodynamic system. In addition, it incorporates the energy that is supplied to the system as heat, as well as any energy that is used as work. Enthalpy is represented by the symbol H and is usually calculated in units of joules (J).

An incompressible substance is one that cannot be compressed or compressed to a significant degree. Liquids are examples of such materials. They are often described as having a constant density because, unlike gases, they do not easily change in volume in response to pressure or temperature changes. Therefore, the change in enthalpy is 0 kJ/kg.

Learn more about Enthalpy here: https://brainly.com/question/16985375.

#SPJ11

Exactly at noon, as determined by the WWV time signal, on successive days of a week the clocks according to their relative value as good timekeepers, best to worst.

Time signals are also used in many everyday applications, such as GPS navigation, where precise timing is essential for calculating positions accurately.  A time signal refers to any signal that provides information about the passage of time. Time signals are often used in experiments to measure the duration of events or to synchronize the timing of multiple processes.

One common type of time signal is a periodic signal, which repeats itself at regular intervals. This can be used to measure the period or frequency of a phenomenon, such as the oscillation of a pendulum or the vibration of a guitar string. Another type of time signal is a pulse signal, which provides a brief burst of energy at a specific time. This can be used to trigger the start or stop of a process or to measure the time delay between different events.

To learn more about Time signal visit here:

brainly.com/question/28875779

#SPJ4

The correct option is B, the areas labeled X, Y, and Z represent constructive interference in which waves strengthen each other.

Interference is a phenomenon that occurs when two or more waves interact with each other. In physics, waves can be described as a disturbance that travels through a medium, such as water or air. When two waves meet, they can either reinforce or cancel each other out, depending on their amplitudes and phases.

Constructive interference occurs when the peaks of two waves coincide, creating a larger amplitude than either wave alone. Destructive interference occurs when the peak of one wave coincides with the trough of another, resulting in a cancellation of the waves. Interference is a fundamental concept in many areas of physics, including optics, acoustics, and electromagnetism.

To learn more about Interference visit here:

brainly.com/question/16098226

#SPJ4

Complete Question:

The diagram shows monochromatic light passing through two openings.

What do the areas labeled X, Y, and Z represent?

A). constructive interference in which waves cancel each other out

B). constructive interference in which waves strengthen each other

C). destructive interference in which waves cancel each other out

D). destructive interference in which waves strengthen each other

In the context of the motor control process related to the speed-accuracy trade-off, the initiation phase of movement includes the beginning of limb movement in the direction of a target.

Motor control is the ability to regulate and coordinate motor skills to achieve a desired outcome. The central nervous system (CNS) is in charge of regulating these skills. The CNS is divided into two parts: the peripheral nervous system (PNS) and the central nervous system (CNS). Motor skills are regulated by both parts of the nervous system. The CNS, on the other hand, is more involved in higher-level motor control.

A motor control system can be divided into three stages: planning, initiation, and execution. When the central nervous system processes the desired movement, it activates the motor program in the initiation stage, which produces the motor command sent to the muscles. Movement is initiated by the initiation stage. Following that, the movement is executed to meet the task's requirements. The motor program adjusts movement by making corrections based on previous trials and feedback. Therefore, the initiation phase is critical in the context of the motor control process related to the speed-accuracy trade-off.

Learn more about Motor control here:

https://brainly.com/question/29769703
#SPJ11

When 872.0 kJ of thermal energy are injected, the temperature of the 25 kg of water in the car's cooling system changes by 35.0 degrees Celsius.

Water's specific heat capacity (J/(gK), or 4,180 J/ (kgK). Thus, we can use the following formula to get the temperature change:

Q = mcΔT

where Q is the extra thermal energy (872 000 J), m the water mass (25 kg), c the water's specific heat capacity (4,180 J/(kg*K)), and T the temperature change.

When we solve for T, we get:

The equation T = Q/(mc) Equals 872,000 J/(25 kg * 4,180 J/(kgK)) = 35.0 °C.

When 872.0 kJ of thermal energy are injected, the temperature of the 25 kg of water in the car's cooling system changes by 35.0 degrees Celsius.

learn more about energy here:

https://brainly.com/question/1932868

#SPJ4

The coordinated functions of the Nervous, Endocrine, and Reproductive systems are:

Coordinated functions refer to the integration and communication between different organs, systems, and tissues in the body to achieve a common goal or purpose. In biological terms, coordinated functions often involve multiple physiological systems working together to maintain homeostasis, respond to stimuli, or carry out complex behaviors or processes.

Examples of coordinated functions include the regulation of blood glucose levels by the pancreas and liver, the coordination of movement by the nervous and musculoskeletal systems, and the release of hormones by the endocrine system to control various physiological processes.

Learn more on coordinated functions here: https://brainly.com/question/15686131

#SPJ1

The question is:

"COORDINATED FUNCTIONS OF THE NERVOUS, ENDOCRINE, AND REPRODUCTIVE SYSTEMS"

Directions: Identify the part of the brain that is involved in each situation below. Write only the letter of your answer.

A. Amygdala

B. Brocka's Area

C. Cerebellum

D. Cerebrum

E. Hippocampus

F. Occipital Lobe

G. Hippocampus

H. Hypothalamus

I. Inferior Colliculus.

J. Thalamus

K. Pons

L Superior Colliculus

M. Pineal Gland

N. Wernicke's Area

O. Pituitary Gland

1. "My heart tells me that you are the one. I love you so much!"

2. "IAOCEVOY! I don't know what that means. It's all Greek to me!"

3. "Chartreuse, Olive,Turquoise, and Mint are all shades of green."

4. "Janna always wakes up at 4 in the morning, regardless of whether she uses an alarm clock or not."

5. "I don't remember the way going to Myla's house. Can you accompany me there?"

6. Jenny's mother is about to give birth, she complains about contraction and pain usually when the baby is kicking

7. "Anthony is a very skilled dancer. He just won the school hip hop dance competition last week."

8. "As Nica was walking on the road she readily moved to the side for she heard an incoming ambulance"

9. "Elsa loves making faces whenever she talks to her friends."

10. "Ryan usually talks about how happy his high school days were to his grandchildren."

The statement the construction of psychological profiles is a process of mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones is TRUE.

Psychological profiling is a technique used by law enforcement agencies to identify the characteristics of an offender based on their behavior patterns, motives, and other psychological traits. It is a process of creating a psychological profile of an offender by analyzing the crime scene, victimology, and other evidence related to the crime.

This profile is then compared with the profiles of previously solved crimes to identify potential suspects or patterns that can be used to solve unsolved crimes. The process involves mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones.

The psychological profile is based on the assumption that an offender's behavior is consistent across different crimes and that it reflects their personality traits and motivations. This technique has been used successfully in many high-profile cases and has helped law enforcement agencies to identify and apprehend serial offenders.

To know more about psychological profiles, refer here:

https://brainly.com/question/30398442#

#SPJ11

The most appropriate option among the given options is C. A white dwarf is what most stars become when they die.What is a white dwarf?A white dwarf is a small, compact object that is the final stage of stellar evolution for most stars in the universe.

The star exhausts its fuel and begins to cool after it has used up all of the hydrogen fuel that powers its nuclear reactions. This phase of a star's evolution is referred to as a red giant. The star then sheds its outer layers of gas, exposing its core. The hot, glowing core of a star is exposed as a white dwarf once the outer layers have been ejected.What most stars become when they die is a white dwarf. This is one of the most fascinating phenomena in the universe, as well as one of the most intriguing. Furthermore, a white dwarf is a dense, compact object that is frequently composed of carbon and oxygen. It has no more nuclear fuel to burn, therefore it does not produce energy. As a result, it gradually fades away into the blackness of space, eventually turning into a black dwarf. However, it is believed that no black dwarfs have been observed yet.White dwarfs are not precursors to black holes or neutron stars, as those objects are formed from more massive stars that undergo different processes at the end of their lives. Brown dwarfs are also different objects, being failed stars that never achieved the temperature and pressure necessary for sustained nuclear fusion.

For more such questions one white dwarf

https://brainly.com/question/13914155

#SPJ11

Answer:

See below.

Explanation:

When the 1500 kg car collides with the wall and rebounds at a speed of 5.00 m/s, we can calculate the change in the car's velocity using the following formula:

Δv = v2 - v1

Where Δv is the change in velocity, v2 is the final velocity, and v1 is the initial velocity. Substituting the given values, we get:

Δv = 5.00 m/s - 20.0 m/s

Δv = -15.0 m/s

The negative sign indicates that the direction of the car's velocity has reversed, or that the car is now moving to the left. To calculate the magnitude of the change in velocity, we take the absolute value:

|Δv| = |-15.0 m/s|

|Δv| = 15.0 m/s

Therefore, the magnitude of the change in velocity is 15.0 m/s.

Now,

To find the magnitude of the average force acting on the car during the collision, we can use the impulse-momentum theorem, which states that:

Impulse = change in momentum

Average force = Impulse / time

The change in momentum of the car is given by:

Δp = mΔv

where Δv is the change in velocity calculated in the previous answer and m is the mass of the car.

Δp = 1500 kg × (-15.0 m/s)

Δp = -22500 kg·m/s

The impulse acting on the car during the collision is equal to the change in momentum:

Impulse = Δp = -22500 kg·m/s

To find the magnitude of the average force acting on the car during the 250 ms collision, we divide the impulse by the duration of the collision:

Average force = Impulse / time

Average force = -22500 kg·m/s / 0.250 s

Average force ≈ -90,000 N

The negative sign indicates that the force is in the opposite direction of the car's motion, or to the left. Therefore, the magnitude of the average force acting on the car during the collision is approximately 90,000 N.

The Volumetric efficiency of the pump is the ratio of the actual capacity to the theoretical capacity of the pump.

Volumetric efficiency of the pump = Actual capacity of the pump / Theoretical capacity of the pump

Given Information

The provided information is,

Find

The theoretical capacity of the pump is given by the following formula,

Theoretical capacity of the pump = π/4 x d² x l x n

where:

For the given problem,

We need to find the diameter of the pump and length of the pump to calculate the theoretical capacity of the pump.

Now, we have the actual capacity of the pump.

As we don't have the diameter and length of the pump, it is impossible to calculate the theoretical capacity of the pump.

Hence, the Volumetric efficiency of the pump cannot be calculated.

Learn more about Volumetric efficiency: https://brainly.com/question/14783214

#SPJ11

When only one lightbulb blows out, an entire string of decorative lights goes out, which means that the lights in this string must be connected in series with one current pathway.

In a series circuit, the components are connected end to end in a single path, so the current flows through each component in turn. If one component, such as a lightbulb, fails, the circuit becomes incomplete, and the current cannot flow through any of the components downstream of the failed component. This results in all the lights in the series circuit going out when one lightbulb blows out.

In contrast, in a parallel circuit, the components are connected across multiple current pathways, so if one component fails, the current can still flow through the other components, and they will continue to function normally. Therefore, if one lightbulb blows out in a parallel circuit, the other lights will continue to work.

Learn more about the series circuit:

https://brainly.com/question/19865219

#SPJ11

To keep the leg in the raised position, the tendon should provide 160N force.

The rotating force or moment of a force around a particular axis or pivot point is measured by torque. The tendency of a force to cause an object to spin along an axis is described as a vector quantity, torque.

Given: combined mass of the lower leg and the foot, m = 3.6kg

position of the center of gravity, r1 = 25cm

r = 0.25m

distance between tendon and lower leg, r2 = 5cm = 0.05m

torque applied will be τ = 3.6 × 10 × 0.25

τ = 8 N-m

the force applied by tendon

F = τ/ r2

F = 8/ 0.05

F = 160N

Therefore, To keep the leg in the raised position, the tendon should provide 160N force.

To know more about torque, click here:

https://brainly.com/question/29024338

#SPJ12

The average arterial pressure in your hands when they are held at your side is 47.5 mmHg.

The average arterial pressure in your hands when they are held at your side can be determined using the hydrostatic pressure formula, which is a function of height, gravity, and density. When the hands are held at the side, they are 60 cm below the heart, which means they are at a distance of 0.6 m.

The hydrostatic pressure formula is given by

P = ρgh

Where,

P is the pressure, ρ is the density, g is the acceleration due to gravity, and h is the height. We can assume that the density of blood is constant, and we can take the value of g to be 9.81 m/s², the standard acceleration due to gravity.

Therefore, the pressure at the heart is 100 mmHg, or 100/760 = 0.131 atm. The pressure in the hands can be calculated as follows:

P = ρghP = (1.06 × 10³ kg/m³) × (9.81 m/s²) × (0.6 m)

P = 6.26 × 10³ N/m²

P = 6.26 × 10³ Pa

P = 47.5 mmHg

Therefore, the average arterial pressure in the hands when they are held at the side is 47.5 mmHg.

Learn more about hydrostatic pressure at https://brainly.com/question/28206120

#SPJ11

The statements that correctly describe the processes occurring in the flask  are A and B. C and D are incorrect statetment.

a) States that the relative amounts of liquid and vapor in the flask remain constant, which is true as equilibrium has been reached, meaning that the rate of evaporation equals the rate of condensation. b) states that molecules are leaving and entering the liquid phase at the same rate, which is also true as equilibrium has been reached.

c) and d) are incorrect because they do not accurately describe the processes occurring in the flask; while the system is at equilibrium, it is still in a state of change with molecules leaving and entering the liquid phase at the same rate.  

Learn more about term of equilibrium: brainly.com/question/517289

#SPJ11

Coordinate , A - the height of the stone when it hits the water. A slingshot sends a stone vertically upward from a height of 20 feet above a pool of water.

The coordinate A represents the height of the stone when it hits the water. When the stone hits the water, its height above the water surface is zero.

So, we can set the expression for the stone's height equal to zero and solve for t to find the time when the stone hits the water. The height of the stone when it is launched is given as 20 feet, which is a fixed value in this problem.

The time when the stone is launched is also a fixed value, which is zero. The maximum height of the stone is the highest point the stone reaches above its initial height of 20 feet. The time when the stone reaches its maximum height is the time at which the vertical velocity of the stone becomes zero.

To know more about vertical velocity , visit :

https://brainly.com/question/11679227

#SPJ1

The work required to raise the elevator from the basement to the third floor is equal to the force times the distance moved. The work required is equal to (-pounds)(ft) = -foot-pounds.

We have to calculate the work required to raise the elevator from the basement to the third floor using the given data. In order to calculate the work, we need to determine the force required to lift the elevator.

This can be done using the equation: F = W + w x L

where, F is the force required to lift the elevator, W is the weight of the elevator, w is the weight of the cable per foot, and L is the length of the cable. F = 1500 + (0.4 × 75) = 1500 + 30 = 1530 pounds.

Therefore, the force required to lift the elevator is 1530 pounds. The work done to raise the elevator is given by the equation: W = F × d

where, W is the work done, F is the force required to lift the elevator, and d is the distance traveled by the elevator.

W = 1530 × 30 = 45,900 foot-pounds.

Therefore, the work required to raise the elevator from the basement to the third floor is 45,900 foot-pounds.

Read more about the distance ;

https://brainly.com/question/26550516

#SPJ11

True. A Faraday bag (also known as an electromagnetic bag) is a container made from metal or a special material that blocks any electromagnetic emanations from passing into or out of the bag, preventing a mobile device from communicating with the outside world.

This is because Faraday bags are electromagnetic bags that are designed to isolate electronic devices from external electromagnetic influence. They are also known as radiofrequency shielding bags, Faraday cage bags, signal blocker bags, or electromagnetic pulse (EMP) bags.

What are Faraday bags?

Faraday bags are made of a combination of metal or metal-coated fabrics that are designed to block electromagnetic signals from entering or leaving the bag. They are usually used to keep mobile devices such as smartphones and tablets from communicating with the outside world, especially in situations where an individual is worried about their privacy or security. They are also used by law enforcement agencies to prevent suspects from remotely wiping or deleting evidence on their devices.

How do Faraday bags work?

Faraday bags work by using a principle known as the Faraday effect, which states that any electric field in a conductor is shielded from the conductor's interior by the presence of an electric field. Faraday bags use this principle to block incoming and outgoing signals by creating an electrically conductive enclosure around the device. This means that when a mobile device is placed inside a Faraday bag, the bag acts as a Faraday cage, which shields the device from electromagnetic radiation. As a result, the device cannot communicate with the outside world.

For further details about Faraday bag, click on the below link:

https://brainly.com/question/23083952

#SPJ11

Answer: Noble Gases (Blue)

The electric field inside the wire is still about 2.27 V/m, even though the electron mobility is 4 times higher. This is because the resistance of the wire remains the same, and Ohm's law still applies. The higher conductivity only means that a higher current flows through the wire for the same voltage, but the electric field remains the same.

We can use Ohm's law to find the electric field inside the Nichrome wire:

V = IR

where

V = 1.7 volts (battery voltage)

I = current

R = resistance of the wire

The resistance of a wire can be calculated using the formula:

R = (ρL) / A

where

ρ = resistivity of the material

L = length of the wire

A = cross-sectional area of the wire

The resistivity of Nichrome is about 1.10 x 10^-6 Ωm, and the cross-sectional area of the wire can be calculated using the formula for the area of a circle:

A = πr^2

where

r = radius of the wire = 0.125 mm = 0.000125 m

So, A = π(0.000125 m)^2 = 4.91 x 10^-8 m^2

Substituting the values, we get:

R = (1.10 x 10^-6 Ωm)(0.75 m) / (4.91 x 10^-8 m^2)

R ≈ 0.017 Ω

Now we can find the current:

I = V / R

I = 1.7 volts / 0.017 Ω

I ≈ 100 amps

The electric field inside the wire can be calculated using the formula:

E = V / L

where

E = electric field

V = potential difference

L = length of the wire

Substituting the values, we get:

E = 1.7 volts / 0.75 m

E ≈ 2.27 volts/meter or 2.27 V/m

So the electric field inside the Nichrome wire is about 2.27 V/m.

Next, we can repeat the calculations for the wire with the higher electron mobility. Since the mobile electron density and the length and diameter of the wire are the same, the resistance of the wire will also be the same as before. However, the higher electron mobility means that the wire will have a higher conductivity, which in turn means that the current will be higher for the same voltage.

Let's assume that the electron mobility is 4 times higher than that of Nichrome. Since the resistivity of the material remains the same, the conductivity will be 4 times higher as well. Therefore, the current will be 4 times higher than before:

I = 4 x 100 amps = 400 amps

Using the same formula as before, the electric field inside the wire can be calculated:

E = V / L

E = 1.7 volts / 0.75 m

E ≈ 2.27 volts/meter or 2.27 V/m

So, the electric field inside the wire is still about 2.27 V/m, even though the electron mobility is 4 times higher. This is because the resistance of the wire remains the same, and Ohm's law still applies. The higher conductivity only means that a higher current flows through the wire for the same voltage, but the electric field remains the same.

For such more questions on Ohm's law

https://brainly.com/question/14634041

#SPJ11

a) The magnetic field at the center of loop 20.0 cm in diameter carrying is equals to the 2.8274×10⁻⁵ T.

b) Smallest magnetic field that change measured value by 0.0100% is equals to the 2.8274×10⁻⁹ T.

We know that moving charges create magnetic fields and magnetic fields exert forces on moving charges, devices that are used to measure field strengths. Consider the wire segment present in above figure.

A) Diameter of wire segment, d = 20 cm or 0.2 m carrying current I = 4.5 A

Magnetic Field at the center of current loop of segment, B= μ₀I/d

= 4π×10⁻⁷×4.5/0.2

= 2.8274×10⁻⁵ T

Therefore magnetic Field at the center of current loop 2.8274×10⁻⁵ T.

B) Current in carrying wire, I = 4.5 A

The field should be less than the measured field by 0.0100%. So, smallest field that change measured value by 0.0100% = 0.0100% of 2.8274×10⁻⁵ T

= 2.8274×10⁻⁹ T

Therefore Smallest field that change measured value by 0.0100% = 2.8274×10⁻⁹ T

For more information about magnetic field, visit :

https://brainly.com/question/26257705

#SPJ4

Complete question:

The above figure completes the question.

Since moving charges create magnetic fields and magnetic fields exert forces on moving charges, devices that are used to measure field strengths often affect the system they are being used to measure. Consider the wire segment in the figure, which is used to measure the magnetic field by determining the foree exerted on the current flowing through it. Part (a) Estimate the field the loop creates by calculating the field strength, in teslas, at the center of a circular loop 20.0 cm in diameter carrying

Part (b) What is the smallest field strength this loop can be used to measure with a 4.5 -A current, if its field should alter the measured field by 0.0100% or less?

The final velocity of the plane after a missile of mass 1.20 102 kg is fired from the plane  is 0.255 m/s.

To find the final velocity of the plane when a missile of mass 1.20 x 10² kg is fired from a plane of mass 4.80 x 10³ kg initially moving at a speed of 3.25 x 10² m/s, and the speed of the missile relative to the plane is 1.06 x 10³ m/s, we can use the conservation of momentum.The initial momentum of the system is given by:

m1v1 + m2v2 = (m1 + m2)vf

where m1 = mass of missile, m2 = mass of the plane, v1 = velocity of the missile, v2 = velocity of the plane, and vf = final velocity of the system

Substituting the given values, we get:(1.20 x 10² kg) (1.06 x 10³ m/s) + (4.80 x 10³ kg) (3.25 x 10² m/s) = (1.20 x 10² kg + 4.80 x 10³ kg) vf

Simplifying, we get:1284 = (5.04 x 10³ kg) vf

Therefore, vf = 1284 / (5.04 x 10³ kg) = 0.255 m/s. So, the final velocity of the plane is 0.255 m/s.

More on velocity: https://brainly.com/question/20038545

#SPJ11

The energy of the incident electron is 26.3 keV. The energy is calculated from the conservation of energy which states that the initial energy is equal to the final energy of the electrons. Total energy is sum of kinetic energy and potential energy of the electrons.

The initial energy of the incident electron can be determined using the following equation:

[tex]E_{initial}= \Delta K + E_{final} + U[/tex]

where ΔK is the change in kinetic energy, [tex]E_{final}[/tex] is the final energy, and U is the potential energy.

Here, the second electron is initially at rest, and after the collision, the trajectories of the two electrons are at 90° to a uniform magnetic field. The magnetic force is perpendicular to the direction of motion, and hence, there is no work done. The potential energy U is, therefore, zero.

Initially, only the incident electron has energy, and hence, its initial energy is equal to its kinetic energy.

[tex]E_{initial} = \Delta K + E_{final}[/tex]

But, [tex]E_{final} = \frac{1}{2}mv_f^2[/tex]

Therefore,

[tex]E_{initial} = \Delta K + \frac{1}{2}mv_f^2[/tex]

The change in kinetic energy ΔK can be calculated using the following equation:

[tex]\Delta K = K_f - K_i[/tex]

But, [tex]K_i = \frac{1}{2}mv_i^2[/tex] where, [tex]v_i[/tex] is the initial velocity of the incident electron.

Therefore,

[tex]\Delta K = K_f - K_i= \frac{1}{2}mv_f^2 - \frac{1}{2}mv_i^2[/tex]

Substituting the given values,

[tex]\Delta K = \frac{1}{2}(9.11 \times 10^{-31} kg)(4.24\times 10^5 m/s)^2 - \frac{1}{2}(9.11\times10^{-31} kg)(3\times10^8 m/s)^2\\= -4.22\times10^{-15} Joules[/tex]

The energy of the incident electron can be converted to keV by dividing it by the charge of an electron and then multiplying by 1000.eV .

Therefore,

[tex]E_{initial} = 4.22 \times 10^{-15} J / (1.602 \times 10^{-19} C/eV)\\ = 26.3 keV[/tex]

Thus, the energy of the incident electron is 26.3 keV.

For further detail on the kinetic energy, click on the following link:

https://brainly.com/question/18461965

#SPJ11

Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7J and 23.5J, for better understand we have to know the meaning of potential energy.

Potential energy in physics is the energy that an item retains as a result of its location in relation to other objects, internal tensions, electric charge, or other elements. Potential energy develops in systems having components whose configurations, or relative positions, determine the amount of the forces they apply to one another.

Potential Energy of an Object = m * g * h

Where, m = mass,

g = gravity, and

h = height

Potential Energy of Object W = 2 * 9.8 * 0

= 0 J

Potential Energy of Object X = 2 * 9.8 * 0.4

= 7.84 J

Potential Energy of Object Y = 2 * 9.8 * 0.8

= 15.68 J

≈ 15.7 J

Potential Energy of Object Z = 2 * 9.8 * 1.2

= 23.5 J

Therefore, Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7 J and 23.5 J.

To Learn more about Potential Energy, visit:

https://brainly.com/question/1242059

#SPJ1

The proper subset relations that are possible using the sets of numbers n, z, q, and r are:

An improper subset comprises every element of the original set, while a valid subset only contains a fraction of the original set's numbers. A subset of a set A that is not equal to A is a proper subset of A. In other words, if B is a proper subset of A, then A has at least one element that is not in B but all of B's elements are in A.

Learn more about proper subset at brainly.com/question/17514113

#SPJ11

At the shop, Joselyn purchased 2700 grammes of salt water taffy.

To convert kilograms (kg) to grams (g), Joselyn would need to multiply the weight in kilograms by 1000. This is because there are 1000 grams in 1 kilogram. Therefore, to find out how many grams of salt water taffy Joselyn bought, she would need to multiply 2.7kg by 1000.

The correct answer is (B) Multiply by 1000.

Multiplying 2.7kg by 1000 gives:

2.7kg x 1000 = 2700g

So Joselyn bought 2700 grams of salt water taffy at the store.

To learn more about salt water refer to:

brainly.com/question/6829606

#SPJ4

Answer:

It would triple.

Explanation:

By Newtown's law of universal gravitation, the ration is 1:1

The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass.

An object-earth system is a system in which an object interacts with the earth by exerting a force of attraction. The object's energy is derived from the work done by gravitational forces when the object is moved away from the earth's surface.

An object in an object-earth system's gravitational potential energy is the work done by gravitational forces on the object when it is moved from a lower position to a higher one in the object-earth system. The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass. The gravitational potential energy of an object in the earth-object system is determined by the distance between the object and the earth's surface. The gravitational potential energy of an object increases as the distance between it and the earth's surface increases.

Learn more about the gravitational potential at brainly.com/question/19768887

#SPJ11

Answer:

D = 3.5 m      to mirror

d = 1.50 m     from mirror to sister

Total distance from camera to sister = d + D = 5.0 m