When methane is burned with oxygen, the products are carbon dioxide and water. If you produce 9 grams of water and 11 grams of carbon dioxide from 16 grams of oxygen, how many

Answers

Answer 1

The given question is incomplete.

The complete question is:

When methane is burned with oxygen, the products are carbon dioxide and water. If you produce 9 grams of water and 11 grams of carbon dioxide from 16 grams of oxygen, how many grams of methane were needed for the reaction?

Answer: 4 grams of methane were needed for the reaction

Explanation:

According to the law of conservation of mass, mass can neither be created nor be destroyed. Thus the mass of products has to be equal to the mass of reactants. The number of atoms of each element has to be same on reactant and product side. Thus chemical equations are balanced.

{tex]CH_4+2O_2\rightarrow CO_2+H_2O[/tex]

Given:  mass of oxygen = 16 g

Mass of carbon dioxide = 11 g

Mass of water = 9 g

Mass of products = Mass of carbon dioxide + mass of water = 11 g  +9 g = 20 g

Mass or reactant = mass of methane + mass of oxygen = mass of methane + 16 g

As mass of reactants = mass of products

mass of methane + 16 g= 20 g

mass of methane  = 4 g

Thus 4 grams of methane were needed for the reaction


Related Questions

A sample of radioactive silver contains two isotopes, 108Ag (denoted A) and 110Ag (denoted B). The second of these (B) has a half life of 24 seconds, whereas the first (A) has a half life of 2.3 minutes. If a sample contains equal numbers of each of these isotopes at the beginning of an experiment that runs for an hour, which of the following statements is correct?
A. At the end of the hour, isotope B has a greater decay constant λ than isotope A
B. At the end of the hour, isotope A has the same decay constant λ as isotope B
C. At the end of the hour, isotope A has a greater decay constant λ than isotope B

Answers

Answer:

A : At the end of the hour, isotope B has a greater decay constant λ than isotope A

Explanation:

Firstly, we need to understand that radioactive decay follows a first order rate law.

What this means is that we can calculate the radioactive decay constant using the following formula from the half-life

Mathematically;

[tex]t_{1/2}[/tex]  = 0.693/λ

where λ represents the radioactive decay constant.

Rearranging the equation, we can have

λ = 0.693/[tex]t_{1/2}[/tex]

Now, to have a fair level playing ground, it is best that the half-life of both isotopes are in the same unit of time(seconds)

For A, the half-life = 2.3 minutes which is same as 2.3 × 60 = 138 seconds

For B, the half-life is 24 seconds

Thus, at the end of the hour, the decay constant for isotope A will be;

λ = 0.693/138 = 0.0050 [tex]s^{-1}[/tex]

For isotope B, the decay constant will be;

λ = 0.693/24 = 0.028875  [tex]s^{-1}[/tex]

We can see that the decay constant of isotope B is higher than that of A at the end of the experiment

1500 L has how many significants figures

Answers

Answer:

It has 2

Explanation:

The significant figures are 1 and 5!

Hope this helps:)

2. Which one is the odd one
out and why?
o Water
• Hydrogen
Chlorine
o Aluminum

Answers

Answer:

Reaction of Chlorine with Hydrogen Chlorine and Hydrogen mixed together explodes when exposed to sunlight, which produces Hydrogen Chloride. In the dark away from sunlight, no reaction occurs, so light energy is required for a reaction. Cl2 + H2 = 2 HCl Reaction of Chlorine with Non-Metals Chlorine directly combines with most non-metals.

Explanation:

I hope this helps bro

Calculate LaTeX: \DeltaΔGº for a voltaic cell with Eºcell = +0.24 V if the overall reaction involves a 3 electron reduction.

Answers

Answer:

-69 kJ

Explanation:

Step 1: Given data

Standard cell potential (E°cell): +0.24 V

Electrons involved (n): 3 mol

Step 2: Calculate the standard Gibbs free energy change (ΔG°) for the voltaic cell

We will use the following expression.

ΔG° = -n × F × E°cell

where,

F is Faraday's constant (96,485 C/mol e⁻)

ΔG° = -n × F × E°cell

ΔG° = -3 mol e⁻ × 96,485 C/mol e⁻ × 0.24 V

ΔG° = -69 kJ

The compound sodium hydroxide is a strong electrolyte. Write the transformation that occurs when solid sodium hydroxide dissolves in water. Use the pull-down boxes to specify states such as (aq) or (s).

Answers

Answer:

Solid sodium hydroxide dissolves in water to form an aqueous solution of ions.

NaOH(s) ⇌ Na+(aq) + OH–(aq) ΔH1 = ?

Solid sodium hydroxide reacts with aqueous hydrochloric acid to form water and an aqueous solution of sodium chloride.

NaOH(s) + H+(aq) + Cl–(aq) ⇌ H2O(l) + Na+(aq) + Cl–(aq) ΔH2 = ?

Solutions of aqueous sodium hydroxide and hydrochloric acid react to form water and aqueous sodium chloride.

Na+(aq) + OH–(aq) + H+(aq) + Cl–(aq) ⇌ H2O(l) + Na+(aq) + Cl–(aq) ΔH3 = ?

. You have two solutions, both with a concentration of 0.1M. Solution A contains a weak acid with a pKa of 5. ThepH of solution A is 3. Solution B contains a weak acid with a pKa of 9. The pH of solution B is:

Answers

Answer:

pH of solution B is 5

Explanation:

A weak acid, HA, is in equilibrium with water as follows:

HA(aq) + H₂O(l) ⇄ A⁻(aq) + H₃O⁺(aq)

Where Ka (10^-pKa = 1x10⁻⁹) is:

Ka = 1x10⁻⁹ = [A⁻] [H₃O⁺] / [HA]

Where concentrations of this species are equilibrium concentrations

As initial concentration of HA is 0.1M, the equilibrium concentrations of the species are:

[HA] = 0.1M - X

[A⁻] = X

[H₃O⁺] = X

Where X is the amount of HA that reacts until reach the equilibrium, X is reaction coordinate.

Replacing in Ka expression:

1x10⁻⁹ = [A⁻] [H₃O⁺] / [HA]

1x10⁻⁹ = [X] [X] / [0.1 - X]

1x10⁻¹⁰ - 1x10⁻⁹X = X²

1x10⁻¹⁰ - 1x10⁻⁹X - X² = 0

Solving for X:

X = -0.00001 → False solution, there is no negative concentrations.

X = 1x10⁻⁵ → Right solution.

As [H₃O⁺] = X

[H₃O⁺] = 1x10⁻⁵M

And pH = -log[H₃O⁺]

pH = 5

pH of solution B is 5

If the amount of radioactive iodine-123, used to treat thyroid cancer, in a sample decreases from 3.2 to 0.4 mg in 39.6 h, what is the half-life of iodine-123?

Answers

Answer:

Half life = 13.197 hour

Explanation:

Given:

Old amount (A₀) = 3.2

New amount (A) = 0.4

Radiation decay time (t) = 39.6 hour

Half life = T(1/2)

Find:

Half life = T(1/2) = T

Computation:

A = A₀[tex]e^{-(\frac{0.693t}{T} )}[/tex]

[tex]e^{-(\frac{0.693t}{T} )}[/tex] = 0.4 / 3.2

-[27.4428 / T] = In (0.125)

-[27.4428 / T] = -2.0794

[27.4428 / T] = 2.0794

T = 13.197

Half life = 13.197 hour

What compound is formed when methyloxirane (1,2-epoxypropane) is reacted with ethylmagnesium bromide followed by treatment with aqueous acid

Answers

Answer:

Pentan-2-ol

Explanation:

On this reaction, we have a Grignard reagent (ethylmagnesium bromide), therefore we will have the production of a carbanion (step 1). Then this carbanion can attack the least substituted carbon in the epoxide in this case carbon 1 (step 2). In this step, the epoxide is open and a negative charge is generated in the oxygen. The next step, is the treatment with aqueous acid, when we add acid the hydronium ion ([tex]H^+[/tex])  would be produced, so in the reaction mechanism, we can put the hydronium ion. This ion would be attacked by the negative charge produced in the second step to produce the final molecule: "Pentan-2-ol".

See figure 1

I hope it helps!

How many atoms of oxygen are in one molecule of water (H2O)? one two four three

Answers

Answer:

there is one atom of oxygen and two atoms of hydrogen

Explanation:

One atom is in oxygen of water

Will a precipitate (ppt) form when 300. mL of 2.0 × 10 –5 M AgNO 3 are added to 200. mL of 2.5 × 10 –9 M NaI? Answer yes or no, and identify the precipitate if there is one

Answers

Answer:

A precipitate will form, AgI

Explanation:

When Ag⁺ and I⁻ ions are in an aqueous media, AgI(s), a precipitate, is produced or not based on its Ksp expression:

Ksp = 8.3x10⁻¹⁷ = [Ag⁺] [I⁻]

Where the concentrations of the ions are the concentrations in equilibrium

For actual concentrations of a solution, you can define Q, reaction quotient, as:

Q = [Ag⁺] [I⁻]

If Q > Ksp, the ions will react producing BaCO₃, if not, no precipitate will form.

Actual concentrations of Ag⁺ and I⁻ are:

[Ag⁺] = [AgNO₃] = 2.0x10⁻⁵ × (300mL / 500.0mL) = 1.2x10⁻⁵M

[I⁻] = [NaI] = 2.5x10⁻⁹ × (200mL / 500.0mL) = 1.0x10⁻⁹M

500.0mL is the volume of the mixture of the solutions

Replacing in Q expression:

Q = [Ag⁺] [I⁻]

Q = [1.2x10⁻⁵M] [1.0x10⁻⁹M]

Q = 1.2x10⁻¹⁴

As Q > Ksp

A precipitate will form, AgI

Read the chemical equation. Mg + 2HCl → MgCl2 + H2 How many moles of MgCl2 are produced from 1 mole of HCl? 0.2 0.5 1.0 1.5

Answers

Answer:

0.5 mol MgCl₂

Explanation:

Step 1: Write the balanced equation

Mg + 2 HCl → MgCl₂ + H₂

In words, 1 mole of Mg reacts with 2 moles of HCl to form 1 mole of MgCl₂ and 1 mole of H₂.

Step 2: Establish the appropriate molar ratio

The molar ratio of HCl to MgCl₂ is 2:1.

Step 3: Calculate the moles of MgCl₂ produced from 1 mole of HCl

1 mol HCl × (1 mol MgCl₂/2 mol HCl) = 0.5 mol MgCl₂

Answer:

it is 2.0, the above one is wrong

Explanation:

I did the test :

How many valence electrons must two atoms share to form a single covalent bond? answers A.2 B.4 C.3 D.1

Answers

Answer:

2

Explanation:

A single covalent bond is formed when two electrons are shared between the same two atoms, one electron from each atom.

Answer:

the answer is 2

Explanation:

Gaseous methane (CH4) will react with gaseous oxygen (O2) to produce gaseous carbon dioxide (CO) and gaseous water (H2O) . Suppose 0.963 g of methane is mixed with 7.5 g of oxygen. Calculate the minimum mass of methane that could be left over by the chemical reaction. Be sure your answer has the correct number of significant digits.

Answers

Answer:

0 g.

Explanation:

Hello,

In this case, since the reaction between methane and oxygen is:

[tex]CH_4+2O_2\rightarrow CO_2+2H_2O[/tex]

If 0.963 g of methane react with 7.5 g of oxygen the first step is to identify the limiting reactant for which we compute the available moles of methane and the moles of methane consumed by the 7.5 g of oxygen:

[tex]n_{CH_4}=0.963gCH_4*\frac{1molCH_4}{16gCH_4}=0.0602molCH_4\\ \\n_{CH_4}^{consumed}=7.5gO_2*\frac{1molO_2}{32gO_2}*\frac{1molCH_4}{2molO_2} =0.117molCH_4[/tex]

Thus, since oxygen theoretically consumes more methane than the available, we conclude the methane is the limiting reactant, for which it will be completely consumed, therefore, no remaining methane will be left over.

[tex]left\ over=0g[/tex]

Regards.

Which of the following contains a nonpolar covalent bond?
O A. Co
B. NaCl
O C. 02
O D. HE

Answers

I think the answer is C. 02

Answer:

The answer is o2

Explanation:

I took the test

All of the following are examples of allotropes of carbon EXCEPT Choose the one alternative that best completes the statement or answers the question. Choose the one alternative that best completes the statement or answers the question. diamond amorphous carbon quartz graphene all of the above

Answers

Answer:

quartz

Explanation:

The correct option would be quartz.

Allotropy is a phenomenon that describes the natural existence of the same element in different forms with different physical characteristics. Allotropes are therefore different forms of the same element.

Carbon as an element has several allotropes which include diamond, graphite, graphene, amorphous carbon, and fullerenes. Quartz is a crystalline solid that is composed of silicon dioxide and not carbon.

Hence, all the options are carbon allotropes except quartz.

Wine goes bad soon after opening because the ethanol dissolved in it reacts with oxygen gas to form water and aqueous acetic acid , the main ingredient in vinegar. Calculate the moles of oxygen needed to produce of acetic acid. Be sure your answer has a unit symbol, if necessary, and round it to significant digits.

Answers

Answer:

0.500 moles of oxygen

Explanation:

Full question says: "Calculate the moles of oxygen needed to produce 0.500 moles of acetic acid.

The reaction of ethanol (C₂H₅OH) with oxygen (O₂) is:

C₂H₅OH + O₂ → CH₃COOH + H₂O

Where 1 mole of ethanol reacts per mole of oxygen to produce 1 mole of acetic acid (CH₃COOH) and 1 mole of water

Based on the chemical equation (1 mole of oxygen produce 1 mole of acetic acid; Ratio 1:1). Thus, if you want to produce 0.500 moles of acetic acid you will need:

0.500 moles of oxygen

19. For the following unbalanced equation: S (s) O2 (g) H2O (l) ----> H2SO4 (aq) At what temperature (K) does O2 have to be if the volume of the gas is 5.01 L with a pressure of 0.860 atm to produce 17.55 grams of H2SO4

Answers

Answer:

195.5 K

Explanation:

We'll begin by writing the balanced equation for the reaction. This is given below:

2S + 3O2 + 2H2O → 2H2SO4

Next, we shall determine the number of mole in 17.55 g of H2SO4. This can be obtained as follow:

Molar mass of H2SO4 = (2x1) + 32 + (16x4) = 2 + 32 + 64 = 98 g/mol

Mass of H2SO4 = 17.55 g

Mole of H2SO4 =...?

Mole = mass /Molar mass

Mole of H2SO4 = 17.55/98

Mole of H2SO4 = 0.179 mole.

Next, we shall determine the number of mole of O2 needed for the reaction. This can be obtained as illustrated below:

From the balanced equation above,

3 moles of O2 reacted to produce 2 moles of H2SO4.

Therefore, Xmol of O2 will react to produce 0.179 moleof H2SO4 i.e

Xmol of O2 = (3 x 0.179) / 2

Xmol of O2 = 0.2685 mole

Therefore, 0.2685 mole of O2 is needed for the reaction.

Finally, we shall determine the temperature of O2. This can be obtained by using the ideal gas equation as follow:

Volume (V) of O2 = 5.01 L

Pressure (P) = 0.860 atm

Number of mole (n) of O2 = 0.2685 mole

Gas constant (R) = 0.0821 atm.L/Kmol

Temperature (T) =..?

PV =nRT

0.860 x 5.01 = 0.2685 x 0.0821 x T

Divide both side by 0.2685 x 0.0821

T = (0.860 x 5.01) /(0.2685 x 0.0821)

T = 195.5 K

Therefore, the temperature of O2 must be 195.5 K.

The combination of a carbonyl group and a hydroxyl group on the same carbon atom is called a ________ group.

a. carbamate group
b. carbonate
c. carboxlate
d. carboxyl

Answers

Answer:

d. carboxyl

Explanation:

The presence of carbonyl group (>C=O)) and a hydroxyl group ( (−OH) on the same carbon atom is called a "carboxyl" group. A carboxyl group is represented as COOH and acts as the functional group part of carboxylic acids.

For example:

Formic acid or Methanoic acid (H-COOH)  Butanoic acid (C3H7-COOH)

Hence, the correct option is "d. carboxyl ".

A student ran the following reaction in the laboratory at 242 K: 2NOBr(g) 2NO(g) Br2(g) When she introduced 0.143 moles of NOBr(g) into a 1.00 liter container, she found the equilibrium concentration of NOBr(g) to be 0.108 M. Calculate the equilibrium constant, Kc, she obtained for this reaction. Kc

Answers

Answer:

1.84 × 10⁻³

Explanation:

Step 1: Write the balanced equation

2 NOBr(g) ⇄ 2 NO(g) + Br₂(g)

Step 2: Calculate the initial concentration of NOBr

0.143 moles of NOBr(g) are introduced into a 1.00 liter container. The molarity is:

M = 0.143 mol / 1.00 L = 0.143 M

Step 3: Make an ICE chart

         2 NOBr(g) ⇄ 2 NO(g) + Br₂(g)

I             0.143               0           0

C              -2x               +2x        +x

E          0.143-2x            2x          x

Step 4: Find the value of x

The equilibrium concentration of NOBr(g) was 0.108 M. Then,

0.143-2x = 0.108

x = 0.0175

Step 5: Calculate the concentrations at equilibrium

[NOBr] = 0.108 M

[NO] = 2x = 0.0350 M

[Br₂] = x = 0.0175 M

Step 6: Calculate the equilibrium constant (Kc)

Kc = [0.0350]² × [0.0175] / [0.108]²

Kc = 1.84 × 10⁻³

A student completed the experiment but found that the total amount of material recovered weighed more than the original sample. What is the most likely source of error and how may it be corrected?

Answers

Answer:

This is due to the water moisture present in the recovered sample.

Explanation:

The total amount of material recovered isn’t meant to weigh more than the original sample. However when this happens then it means there is the presence of water moisture in the recovered sample.

The recovered samples however needs to be heated to make it dry and eliminate the water moisture through evaporation.

Which of the following compounds is more soluble in a 0.10 M NaCN solution than in pure neutral water? Ca3(PO4)2 AgBr CaCO3 Mg(OH)2 NH4ClO4

Answers

Answer:

AgBr

Explanation:

Silver bromide has a very low solubility product constant of about 7.7 ×10^-13 in pure water hence it is not quite soluble in pure water.

However, with NaCN, the AgBr forms the complex [Ag(CN)2]^2- which has a formation constant of about 5.6 ×10^8. This very high formation constant implies that the complex is easily formed leading to the dissolution of AgBr in NaCN.

The equation for the dissolution of AgBr in cyanide is shown below;

AgBr(s) + 2CN^-(aq) ----> [Ag(CN)2]^2-(aq) + Br^-(aq)

Need help with chemistry questions

Answers

Answer:

1. oxidation

2. reduction

3. oxidation

4. oxidation

Explanation:

Oxidation and Reduction in terms of hydrogen

Oxidation and Reduction with respect to Hydrogen Transfer. Oxidation is the loss of hydrogen. Reduction is the gain of hydrogen.

Oxidation and Reduction in terms of Oxygen

Oxidation and Reduction with respect to Oxygen Transfer. Oxidation is the gain of Oxygen. Reduction is the loss of Oxygen.

For the following reaction, 22.8 grams of diphosphorus pentoxide are allowed to react with 13.5 grams of water . diphosphorus pentoxide(s) water(l) phosphoric acid(aq) What is the maximum mass of phosphoric acid that can be formed

Answers

Answer:

[tex]m_{H_3PO_4}=31.5gH_3PO_4[/tex]

Explanation:

Hello,

In this case, the undergoing chemical reaction is:

[tex]P_2O_5(s)+3H_2O(l)\rightarrow 2H_3PO_4(aq)[/tex]

Thus, since the diphosphorus pentoxide to water molar ratio is 1:3 and we are given the mass of both of them, for the calculation of the maximum mass phosphoric acid that is yielded, one could first identify the limiting reactant, for which we compute the available moles of diphosphorus pentoxide (molar mass 142 g/mol):

[tex]n_{P_2O_5}=22.8gP_2O_5*\frac{1molP_2O_5}{142gP_2O_5}=0.161molP_2O_5[/tex]

And the moles of diphosphorus pentoxide that are consumed by 13.5 g of water (molar mass 18 g/mol):

[tex]n_{P_2O_5}^{consumed}=13.5gH_2O*\frac{1molH_2O}{18gH_2O}*\frac{1molP_2O_5}{3molH_2O} =0.25molP_2O_5[/tex]

Hence, since less moles of diphosphorus pentoxide are available, we sum up it is the limiting reactant, therefore, the maximum mass of phosphoric acid (molar mass 98 g/mol) is computed by considering the 1:2 molar ratio between them as follows:

[tex]m_{H_3PO_4}=0.161molP_2O_5*\frac{2molH_3PO_4}{1molP_2O_5} *\frac{98gH_3PO_4}{1molH_3PO_4} \\\\m_{H_3PO_4}=31.5gH_3PO_4[/tex]

Regards.

An atom of 108Te has a mass of 107.929550 amu. Calculate the binding energy per MOLE in kJ. Use the values: mass of 1H atom

Answers

Answer:

The binding energy = 8.64972649×10¹⁰ kJ/mole

Explanation:

Given that:

An atom of 108Te has a mass of 107.929550 amu.

In a 108 Te atom, there are 52 protons and 56 neutrons

where;

mass of proton= 1.007825 amu

mass of neutron= 1.008665 amu

Similarly; The atomic number of Te = 52

the mass of 52 protons = 52 ×  1.007825  amu

the mass of 52 protons = 52.4069 amu

the mass of 56 neutrons = 56 ×  1.008665 amu

the mass of 56 neutrons = 56.48524 amu

The total mass can now be = the mass of 52 protons + the mass of 56 neutrons

The total mass = 52.4069 amu +  56.48524 amu

The total mass = 108.89214  amu

Recall  : it is given that An atom of 108Te has a mass of 107.929550 amu.

Therefore, the mass defect will be = 108.89214  amu - 107.929550 amu

the mass defect = 0.96259amu

where 1 amu = 1.66× 10⁻²⁷ kg

Therefore, 0.96259amu = (0.96259  × 1.66× 10⁻²⁷) kg

= 1.5978994 × 10⁻²⁷kg

The binding energy = mass defect × (speed of light)²

where;

speed of light c = 2.99792 × 10⁸ m/s

The binding energy = 1.5978994 × 10⁻²⁷kg  ×  2.99792 × 10⁸ m/s

The binding energy = 1.43611597 × 10⁻¹⁰  J

The binding energy =  1.43611597 × 10⁻¹³ kJ/atom

since 1 mole = 6.023 × 10²³ atom (avogadro's constant)

Then;

The binding energy = ( 1.43611597 × 10⁻¹³ )× (6.023 × 10²³)  kJ/mole

The binding energy = 8.64972649×10¹⁰ kJ/mole

In a buffer solution made of acetic acid and sodium acetate, if a small amount of acid is added, the added acid will react with whome?

Answers

Answer:

The acid reacts with the conjugate base producing more weak acid.

Explanation:

A buffer solution is defined as the mixture of a weak acid and its conjugate base or a weak base with its conjugate acid.

The acetic buffer, CH₃COOH/CH₃COO⁻, is in equilibrium with water as follows:

CH₃COOH(aq) + H₂O(l) ⇄ CH₃COO⁻(aq) + H₃O⁺

When an acid HX (Source of H₃O⁺) is added to the buffer, the reaction that occurs is:

CH₃COO⁻ + HX → CH₃COOH

The acid reacts with the conjugate base producing more weak acid.

In fact, this is the principle of the buffer:

An acid reacts with the conjugate base producing weak acid. And the weak acid reacts with a base producing conjugate base

If a small amount of acid is added to an acetic acid-sodium acetate buffer, the acid will react with the acetate ion from sodium acetate.

We have a buffer formed by acetic acid and sodium acetate.

What is a buffer?

A buffer is a solution used to resist abrupt changes in pH when an acid or a base is added.

How are buffers formed?

They can be formed in 1 of 2 ways:

By a weak acid and its conjugate base.By a weak base and its conjugate acid.

Our buffer is formed by a weak acid (acetic acid) and its conjugate base (acetate ion from sodium acetate).

When an acid (HX) is added, it is neutralized by the basic component of the buffer. The generic net ionic equation is:

H⁺ + CH₃COO⁻ ⇄ CH₃COOH

If a small amount of acid is added to an acetic acid-sodium acetate buffer, the acid will react with the acetate ion from sodium acetate.

Learn more about buffers here: https://brainly.com/question/24188850

For each of the following reactions calculate the mass (in grams) of both the reactants that are required to form 15.39g of the following products.
a. 2K(s) + Cl2(g) → 2Cl(aq)
b. 4Cr(s) + 302(g) → 2Cr2O3(s)
c. 35r(s) + N2(g) → SraNa(s)

Answers

Answer:

a.

[tex]m_K=8.056gK\\ \\m_{Cl_2}=4.028gCl_2[/tex]

b.

[tex]m_{Cr}=10.51gCr\\ \\m_{O_2}=4.851gO_2[/tex]

c.

[tex]m_{Sr}=13.88gSr\\\\m_{N_2}=1.479gN_2[/tex]

Explanation:

Hello,

In this case, we proceed via stoichiometry in order to compute the masses of all the reactants as shown below:

a. [tex]2K+Cl_2\rightarrow 2KCl[/tex]

[tex]m_K=15.36gKCl*\frac{1molKCl}{74.55gKCl}*\frac{2molK}{2molKCl}* \frac{39.1gK}{1molK}=8.056gK\\ \\m_{Cl_2}=15.36gKCl*\frac{1molKCl}{74.55gKCl}*\frac{1molCl_2}{2molKCl}* \frac{70.9gCl_2}{1molCl_2}=4.028gCl_2[/tex]

b. [tex]4Cr+ 3O_2\rightarrow 2Cr_2O_3[/tex]

[tex]m_{Cr}=15.36gCr_2O_3*\frac{1molCr_2O_3}{152gCr_2O_3l}*\frac{4molCr}{2molCr_2O_3}* \frac{52gCr}{1molCr_2O_3}=10.51gCr\\ \\m_{O_2}=15.36gCr_2O_3*\frac{1molCr_2O_3}{152gCr_2O_3l}*\frac{3molO_2}{2molCr_2O_3}* \frac{32gO_2}{1molCr_2O_3}=4.851gO_2[/tex]

c. [tex]3Sr(s) + N_2(g) \rightarrow Sr_3N_2[/tex]

[tex]m_{Sr}=15.36gSr_3N_2*\frac{1molSr_3N_2}{290.86gSr_3N_2}*\frac{3molSr}{1molSr_3N_2}* \frac{87.62gSr}{1molSr}=13.88gSr\\\\m_{N_2}=15.36gSr_3N_2*\frac{1molSr_3N_2}{290.86gSr_3N_2}*\frac{1molN_2}{1molSr_3N_2}* \frac{28gN_2}{1molN_2}=1.479gN_2[/tex]

Regards.

Why are cells important to an organisms survival

Answers

Answer:

Cells are the basic structures of all living organisms. Cells provide structure for the body, take in nutrients from food and carry out important functions. ... These organelles carry out tasks such as making proteins?, processing chemicals and generating energy for the cell

Answer: I absolutely love this question! Biology is so interesting, so I always love to answer the curiosity of others regarding biology, such as that!

Cells are simply the basic structures of all organisms, that are living, of course! Cells provide structure for the body, and they also take in nutrients that your body needs from food and they carry out important functions. These organelles carry out tasks such as making proteins, processing chemicals, and generating energy for the cell. Isn’t that cool?

Hope this helped! <3

A spontaneous galvanic cell consists of a Pb electrode in a 1.0 M Pb(NO3)2 solution and a Cd electrode in a 1.0 M Cd(NO3)2 solution. What is the standard cell potential for this galvanic cell

Answers

Answer:

0.27 V

Explanation:

Given that the both half cells contain 1.0 molar solutions of their respective electrolytes.

E°Pb= -0.13 V

E°Cd = -0.40 V

Since it is a galvanic cell, the electrode having a more negative electrode potential will serve as the anode and the electrode having a less negative electrode potential will serve as the cathode.

Hence cadmium will serve as the anode and lead will serve as the cathode.

E°cell = E°cathode - E°anode

E°cell = -0.13 - (-0.40)

E°cell = 0.27 V

A compound is found to contain 30.45 % nitrogen and 69.55 % oxygen by weight. To answer the questions, enter the elements in the order presented above. 1. What is the empirical formula for this compound? 2. The molecular weight for this compound is 46.01 g/mol. What is the molecular formula for this compound?

Answers

Answer:

Empirical formulae is NO2

Molecular Formulae is NO2

Methyl iodide reacts irreversibly with azide ion with rate = k[CH3I][N3–]. CH3I(aq) + N3–(aq) → CH3N3(aq) + I–(aq) The reaction is carried out with an initial concentration of CH3I of 0.01 M. Which statement about the reaction is correct?

Answers

Answer:

(D) The reaction cannot take place in a single elementary step

Explanation:

Statements are:

(A) The time it takes for [CH3I] to decrease to 0.005 M is independent of [N3-], as long as [N3] >> [CH3I].

B) If the initial concentrations of azide and CH3I are equal, then it takes half as long for [CH3I] to decrease to 0.005 M as it does for it to decrease from 0.005 M to 0.0025 M.

(C) The reaction rate is significantly smaller if excess I- is added to the solution.

(D) The reaction cannot take place in a single elementary step.

The rate of the reaction is:

rate = k[CH3I][N3–].

That means rate depends of concentration of CH₃I as much as N₃⁻ concentration

(A) The time it takes for [CH3I] to decrease to 0.005 M is independent of [N3-], as long as [N3] >> [CH3I]. FALSE. The reaction rate depends of N₃⁻ as much as CH₃I

B) If the initial concentrations of azide and CH3I are equal, then it takes half as long for [CH3I] to decrease to 0.005 M as it does for it to decrease from 0.005 M to 0.0025 M. FALSE. Reaction is second-order. Half-life is 1/K[A]₀. If initial concentration is 0.1M, to a concentration of 0.005M it takes:

1/K*0.1. If initial concentration is 0.005M it takes 1/K*0.005. That means it takes half to decrease from 0.005M to 0.0025 as it does for it to decrease from 0.01M to 0.005M.

(C) The reaction rate is significantly smaller if excess I- is added to the solution. FALSE. Reaction rate is independent of I⁻

(D) The reaction cannot take place in a single elementary step. TRUE. As this reaction is a single-replacement reaction implies the formation  of 1 C-N bond. But also the rupture of the C-I bond is impossible to explain this kind of reaction in a single elementary step.

Other Questions
I need help on this question please. what is bipolar ? what a biploar will be doing when they got mad ? what is the hypothesis If the length of the legs of a right triangle are 13 and 13,what is the length of the hypotenuse? Round your answer to the nearest tenth,if necessary. Andy tells Ervin and Marina that everyone will lose their jobs if the company goes out of business, whether they have guild protection or not. Which influence tactic is Andy most likely utilizing?consultationrational persuasionlegitimating tacticsingratiationexchange Which of the reactions are spontaneous (favorable)? DHAPglyceraldehyde-3-phosphateG=3.8 kJ/mol C4H4O5C4H2O4+H2OG=3.1 kJ/mol C2H4+H2Rh(I)C2H6G=150.97 kJ/mol glutamate+NAD++H2O 2Drag the tiles to the correct boxes to complete the pairs.Match the terms with their meanings.AtmanSamsaraMokshacycle of birth and deathsoulultimate spiritual goalResetNext What is the numerical coefficient of the linear term of the quadratic equation 3x2 9 =0? which law states that the pressure and absolue tempeture of a fixed quantity of gas are directly proportional under constant volume conditions? help help help help help help A control clinic offers a program that guarantees a weight loss of up to 0.46 kg in one week. Express the weight loss in a ratio of milligrams per second. HELP ASAP THANKS!!!!!!!!!!!!!!! Brainliest to right answer!!! Find x.A. 21(route)2B. 7C.21(route)3/2D. 21(route)2/2 Jessica:Farewell, good Launcelot.Alack, what heinous sin is it in meTo be ashamed to be my fathers daughterWhat was the purpose of Launcelots visit? Where does the scene take place? Who was he going to serve? An object has a mass of 4.9g and a volume of 14.ml.what is the density of the object? In the reaction of Zn(s) + 2HCl (aq) Imported Asset ZnCl2 (aq) + H2 (g), if [HCl] increases from 2.6 M to 8.2 M: The rate at which Zn disappears decreases. The rate at which H2 appears decreases. The rate at which ZnCl2 appears increases. The concentration of Zn (s) also increases. At the B end of the recessed horizontal bar, forces F1 and F2 of magnitudes 3 KN and 2KN respectively are applied and oriented as shown in the figure. Determine the magnitude of the resulting force and its orientation with respect to the horizontal. MV Corporation has debt with market value of million, common equity with a book value of million, and preferred stock worth million outstanding. Its common equity trades at per share, and the firm has million shares outstanding. What weights should MV Corporation use in its WACC? What does the term grueling connote about the work of slaves? A. The work was finished quickly. B. The work was cruel and inhumane. C. The work was important and necessary. D. The work was expensive to complete. I NEED HELP PLEASE!!!!!! >:((((( A project has an initial cost of $18,400 and produces cash inflows of $7,200, $8,900, and $7,500 over three years, respectively. What is the discounted payback period if the required rate of return is 16 percent