When light reflects from a surface, there is a change in its intensity. Thus, the correct option is C.
What is Light intensity?Light intensity is also known as luminous intensity. It is the amount of light which is falling on a surface over any given square foot or square meter in size. Light intensity can be measured in terms of lumens per square foot (foot candles) or lumens per square meter (lux).
Light intensity is affected by various factors such as surface on which the light rays strike, the medium, reflection, and the refraction of light.
When a ray of light reflects from a surface, there is a change in the intensity of light and also the speed of light in that medium.
Therefore, the correct option is C.
Learn more about Light intensity here:
https://brainly.com/question/9195922
#SPJ5
Your question is incomplete, most probably the complete question is:
When light reflects from a surface, there is a change in its:
a. frequency
b. velocity
c. intensity
d. phase
State a hypothesis about your estimated daily water use.
Answer
Estimates vary, but, on average, each person uses about 80-100 gallons of water per day, for indoor home uses.
Explanation:
A fairly efficient steam turbine engine fired by coal is used to drive an electric generator. The generator operates between 2100°C and 385°C.
(a) Determine the maximum possible efficiency of the engine.
Answer: 72.3 %
Formula:
e = 1 - (Tc / Th) = 1 - (Qc / Qh) = ( W / Qh)
Explanation: Unsure??
(b) The engine absorbs 1.15 105 J from the hot reservoir every second. If the actual efficiency of the engine is 40.3%, determine the mechanical power the engine delivers.
Answer: 46 kW
Explanation:
Energy absorbed by the engine (J) * actual efficiency of the engine (%) = mechanical power the engine delivers (kW)
How does 1 - (385/2100) = 72.3 % ?
What do I Plug in to make e = 72.3 %
Use kelvin not celsius
C + 273 = K
This will fix my problem of the equation not making sense.
An "energy bar" contains 26 ggof carbohydrates.How much energy is this in joules?
Rubies are used in electronics.
Please select the best answer from the choices provided
) Т
) F
Suppose you were able to take measurements of current through the
resistor and voltage across the resistor. Your record of numerical values is written in a
tabular data below
Answer:
see attached
Explanation:
It will be easier to plot the data if you have grid lines to work with.
In the attached, we had to reverse the order of entries in the table, because the graphing program likes the independent variable listed first.
This should be pretty easy i think.
Describe the components within the system involved in the collision between pilot and landing zone.
Answer:
its a sure for not but i think its a 192583
If the submarine intends to submerge to a depth of 150 m, what pressure must it be designed to withstand
Explanation:
Hydrostatic pressure, P = hdg where d is density if the liquid ( water)
P= 150m × 1000kgm-3 × 10ms-2
P= 1.5 ×10^6 Pa
Why is wrestling ring floor always softThis is physics
Answer:
So the people in the ring don't get hurt or break anything on impact once they hit the floor
Help me quick!!! please!!
Calculate the power of an engine which raises a mass of 1000 kg to a height of 40 m in 10 s.
Answer:
39.240 W
Explanation:
Let's start by calculating the work done by the engine. We can assume that it is the same work done by the weight of the object to bring it from 40m to the surface: as much energy it takes to bring it up, the same ammount it takes to bring it down. Said work is [tex]w= \vec F\cdot \vec{h} = mg h = 1000 \times 9.81\times 40 = 392.400 J[/tex]
At this point we can simply apply the definition of power, that is [tex]P = \frac wt[/tex], to get the power of the engine is [tex]39.240 W[/tex]
Answer:
P=39200W
Explanation:
P=(mgh)/t
P=(40×9.8×1000)/10
P=39200W
we cannot see the milky way galaxy without binocular or telescopes. true or false?
Answer:
I'm pretty sure it's false
Explanation:
.
the primary factor in decreasing the kinetic energy of an object is to
Answer:
Decreasing the velocity
Explanation:
The primary factor in decreasing the kinetic energy of an object is to decrease the velocity of the object.
What is Kinetic energy?The kinetic energy of an object is the energy which it possesses due to the motion of the object. Kinetic energy is defined as the work which is needed to accelerate an object of a given mass from the state of rest to its stated velocity and direction. Gain of the energy during the acceleration of an object, the body maintains this kinetic energy unless its speed changes and the object accelerates.
The kinetic energy is directly proportional to the mass and the velocity of the object. The primary factor which is responsible for the decrease in the kinetic energy of an object is to decrease the velocity of the object.
Learn more about Kinetic energy here:
https://brainly.com/question/15764612
#SPJ6
I'll give brainliest
Answer: figuratively speaking both the lines for the force Q and force P is equal.
which term is most applicable to a discussion of angular momentum in the context of black holes?
A: Photon
B: Curvature
C: Spin
D: Time
Answer:
c: spin
Explanation:
it's not curvature
The most applicable term to a discussion of angular momentum in the context of black holes is Spin. Thus, the correct option is C.
What is angular momentum of black holes?
Angular Momentum is defined as the property of any rotating object which is given by the product of the moment of inertia of an object and the angular velocity of the rotating object. Angular momentum is a vector quantity and it has both the magnitude and direction. The examples of angular momentum are the rotation and revolution of the Earth.
When the astronomers claim that they have estimated the spin of a black hole, this means they have measured its angular momentum. This is the total angular momentum of all the materials on the Universe that ever crossed the event horizon and got trapped inside it.
Therefore, the correct option is C.
Learn more about Angular momentum here:
https://brainly.com/question/29563080
#SPJ2
Which key phrase below would imply that an object has no (0) initial velocity?
1) smoothly
2) in motion
3) backwards
4) from rest
5) uniformly
I assume number 4.
The key phrase which describes zero (0) initial velocity is from rest.
When the velocity of an object at initial time is zero (0), it implies that the change in the displacement of the object with time is zero
[tex]v= \frac{\Delta x}{\Delta t} \\\\v_0 = 0[/tex]
Generally, when an starts its motion from rest, the initial velocity of the object will be zero. As the object acquires more momentum, the velocity increases with time.
Thus, we can conclude that the key phrase which describes zero (0) initial velocity is from rest.
Learn more about initial velocity here:https://brainly.com/question/19365526
What quantity is represented by the mass number minus the atomic number?.
Answer:
Mass = mass of nucleus
Atomic Number = number of protons (charge) of nucleus
Mass - Atomic Number = number of neutrons
A block with a mass of 6.0 kg is
held in equilibrium on an incline
of angle θ = 30.0° by a horizontal
force, F, as shown in the figure.
Find the magnitudes of the
normal force on the block and of F. (Ignore friction.)
(a) The normal force on the block is 50.92 N.
(b) The horizontal force on block keeping it in equilibrium is 29.4 N.
The given parameters;
mass of the block, m = 6 kgangle of inclination, θ = 30.0°The normal force on the block is calculated as follows;
[tex]F_n = W \times cos(\theta)[/tex]
where;
W is the weight of the block[tex]F_n = mg \times cos(\theta)\\\\F_n = 6 \times 9.8 \times cos(30)\\\\F_n = 50 .92 \ N[/tex]
The horizontal force on block keeping it in equilibrium is calculated as follows;
[tex]F- F_x = 0\\\\F-mgsin\theta= 0\\\\F = mgsin\theta\\\\F = 6 \times 9.8 \times sin(30)\\\\F = 29.4 \ N[/tex]
Learn more here:https://brainly.com/question/24860178
How does the radius of a string affect centripetal force.
Answer:
because a raduis is half of 25% of a cicrle.
Explanation:
Prove that the two equations shown below are equivalent.
F = ma and F = p/t
Newton’s Second Law of Motion is defined as Force is equal to the rate of change of momentum. For a constant mass, force equals mass times acceleration.
[tex]\Delta p = mv - mu \\\\\implies \Delta p = m(v-u) \\\\F = \dfrac{\Delta p}{\Delta t} = \dfrac{m(v-u)}{\Delta t} = ma[/tex]
F = ma is the formula of Newton’s Second Law of Motion.
To prove Newton's second law of motion,
Given Force F = Δp/Δt
What is relation between F = ma and F = Δp/Δt?Newton’s Second Law of Motion is defined as Force is equal to the rate of change of momentum. The second law of Newton can be described as the acceleration of an object which produces a net force is directly proportional to the magnitude of the net force, in the same path i.e., direction as the net force, and inversely proportional to the mass of the object.As the acceleration has its magnitude and direction it is a vector quantity.Proof for F=ma
Let us consider an object of mass m, moving along a straight line with an initial velocity u, final velocity v and it has some particular time t and thus Momentum can be related as,
For initial velocity u, p1 = m × u
The final velocity v, p2 = m × v
The change in momentum can be expressed as
p2 – p1 = (m × v) – (m × u)
p2 – p1 = m (v – u)
Here, we know that the rate of change of momentum with respect to time is proportional to the applied force.
The applied force F,
F ∝ [m (v – u)]/t
F ∝ m × a
As acceleration (a) is the rate of change of velocity with respect to time.
F = k × m × a
F = ma
where k can be the constant.
Learn more about Newton's second law,
https://brainly.com/question/13447525
#SPJ2
2. If Joe rides his bicycle in a straight line for 15 min with an average velocity of 12.5 km/h south, how far has he ridden?
Answer:
3.125 Kilometers
Explanation:
To answer this you just multiply 12.5 by .25 (since 15 minutes is a quarter of an hour) to get 3.125 kilometers ridden.
What is a thought experiment?
Answer:
A thought experiment is an experiment carried out only in the imagination
Explanation:
pluto is part of the kuiper belt. what captured moon likely originated in the kuiper belt?
moon Triton, Neptune's largest moon Triton
The moon Triton is the captured moon which most likely originated in the Kuiper belt.
What is Kuiper belt?This is defined as a donut-shaped region beyond Neptune and has an extension from 30 to 50 AU or more from the Sun.
The moon Triton is the captured moon which originates from this belt thereby making it the most appropriate choice.
Read more about Kuiper belt here https://brainly.com/question/14154493
please answer right please
Answer:
i think its A
Explanation:
I hope this helps :)
Da 6.0 kg wooden crate slides across a wooden floor
at a speed of 2.4 m/s, it it takes an applica force
of 25 N to keep it going at a steady speed. What is the
coe of kinetic friction between the floor and crate?
Answer:coe?
Explanation:
The product of pressure and volume of any gas equals a constant, k. What variable(s) must not change in order for the value of k to remain constant
How does the diameter of a black hole (size of the event horizon) depend on the mass inside the black hole
Answer:
The greater the mass, the greater is the diameter
Explanation:
The greater the mass, the greater is the diameter. almost all galaxies contain supermassive black holes.
help -----------------------------------------
Answer:
H,G,E,D,C,B,A,I,F
Explanation:
F is an ignious intrusion and I cross cuts H to A so it must be newer.
PLEASE ANSWER NEED HELP!!!!!!!! PLEASE THE CORRECT ANSWER!!!!!!
Zhiyu wants to start an exercise program. He knows that he should talk to his doctor, but he cannot get an appointment for several weeks. He does not have any health conditions. What is the BEST advice for Zhiyu?
A.
All exercise needs to be medically supervised, so he must wait.
B.
There is always a risk of injury, so he needs professional advice before he starts.
C.
He can start slowly with low impact activity like walking or light weightlifting.
D.
He should do whatever he feels like; his body will let him know if he overdoes it.
PLEASE NO LINKS OR I WILL REPORT YOU
Answer:
c
Explanation:
Study the three pieces of evidence for the Big Bang in this activity carefully. What is common to all these pieces of observable evidence and why does this make them much more powerful than if they did not have this common feature?
Answer:
Explanation:
the measured abundances of elementsthe observed expansion of spacethe discovery of cosmic wave backgroundThe common observable evidence are:
the measured abundances of elementsthe expansion of spacethe cosmic wave backgroundWhat is big bang?The big bang is the theory which explains that how the universe began. It says that the universe began with just a single point. It went on expanding and stretched to grow as large as possible. It is still now expanding.
The big bang consist of fully dark matter, interstellar gases or dust. The big bang is increasing just because in universe there is abundant of hydrogen and helium.
The radiations come from the big bang. These rays are also called as cosmic wave. This big bang is still on it way of expanding more.
Thus, the observational evidence are the measured abundances of element, the expansion of space and the cosmic wave background.
Learn more about big bang.
brainly.com/question/18297161
#SPJ2
How much would a 70 kg student weigh on Pluto? (massPluto = 1.25 x 1022 kg, radiusPluto = 1.20 x 106 m)
Answer: the weight would be 4.6 (I think i don’t know))
Explanation:
A 75.0 kg man pushes on a 500,000 kg wall for 250 s but it does not move.
[tex]▪▪▪▪▪▪▪▪▪▪▪▪▪ {\huge\mathfrak{Answer}}▪▪▪▪▪▪▪▪▪▪▪▪▪▪[/tex]
The work done in the given case is 0
[tex] \large \boxed{ \mathfrak{Step\:\: By\:\:Step\:\:Explanation}}[/tex]
For calculating the work done by an object we apply the formula, that is ~
[tex]f \times s \times \cos( \theta) [/tex]where f represents force applied, and s represents displacement.
but here, the displacement is zero since the wall didn't move at all, Therefore If we plug it's value as 0, we get
[tex]f = 0 \times s \times \cos( \theta) [/tex]hence,
[tex]work \: done = 0[/tex]So therefore, we can conclude that the man hasn't done any work.
Hope it helps.
Do comment if you have any query.
