All atoms of the same element:
have the same number of atoms
have the same number of protons
have the same number of neutrons
have the same number of electrons
Answer:
have the same number of protons
PLZ HELP Which of the following accurately matches a structure to its function? A. Structure: flaps of skin stretched between the front and back legs of a flying squirrel. Function: to allow the squirrel to glide on air
B. Structure: ball-and-socket joint in a human hip. Function: to allow the person to jump.
C. Structure thin membranes in webbed feet. Function: to allow the animal to walk quickly on land.
D. Structure: fish's swim bladder. Function: to allow the fish to move forward through water by releasing air from its swim bladder.
Answer:
a
Explanation:
the flying squirrel the air guides to navagate in the air
CORRECT ANSWER ONLY ND WILL GIVE BRAINLIEST✌
Calculate the mass of nitrogen dioxide gas that would occupy
the same volume as 10g of hydrogen gas at ē same pressure and temperature
(H= 1.0 N = 14.0 O= 16.0) GAS LAWS/MOLES
Answer:
150g
Explanation:
Assuming they are ideal gases at the same temperature and pressure, equal moles of gasses have equal volume. IN this case, if we have 10g of hydrogen gas, that is 5 moles of H2 gas. That means 5 moles og NO2 will occupy the same volume which is 5*(14.0 + 16.0*2) = 230 g
If carbon was the most common element found in the moons and planets, what element is
missing that would make them similar to Earth?
Which of these hypotheses cannot be tested?
A. The percentage of salt in ocean water stays the same throughout the ocean.
O B. Doubling the amount of salt in a bread recipe will cause the dough to rise faster.
C. Cooks should use sea salt in recipes instead of regular table salt.
O D. Increasing the amount of salt in salt water will increase the boiling point.
Cooks should use sea salt in recipes instead of regular table salt.
write molecular formula
1)aurric cloride
2)aluminium hydroxide
3)potassium thiosulphate
4)magnesium bicarbonate
5)magnesium sulphate
6)sodium oxide
7)cuprous oxide
8)mercuric oxide
9)calcium nitrate
10)aluminium oxide
11)ferric chloride
12)ammoium oxide
13)silver chloride
14)hydrogen bromide
15)magnesium nitride
16)hydrogen peroxide
17)sodium sulphate
18)ammonium sulphate
19)ferrous sulphate
20)sodium carbonate
21)zinc carbonate
22)calcium silicate
23)zinc carbonate
24)potassium clorate
25)aluminium hydroxide
26)ammonium hydroxide
27)sodium silicate
Okay.
Here's your below answers.
1) AuCl3.
2) Al(OH)3.
3) K2S2O3.
4) Mg(HCO3)2.
5) MgSO4.
6) Na2O.
7) CuO.
8) HgO.
9) Ca(NO3)2.
10) Al2O3.
11) FeCl2.
12) (NH4)2O.
13) AgCl.
14) HBr.
15) Mg3N2.
16) H2O2.
17) Na2SO4.
18) (NH4)2SO4.
19) FeSO4.
20) Na2CO3.
21) ZnCO3.
22) CaSiO3.
23) ZnCO3.
24) KClO3.
25) Al(OH)3.
26) NH4OH.
27) Na2SiO3.
What functional group does the molecule below have?
*two leg spider looking molecule*
Answer:
ether
Explanation:
Ether, any of a class of organic compounds characterized by an oxygen atom bonded to two alkyl or aryl groups. I attached an image as well.
Answer:
D. Ether
Explanation:
Ethers look like R---O---R. Thus, this molecule has the ether functional group. :)
write an equation for the reaction between nitrogen (ii) oxide and iron (ii) sulphide
Answer:
Let us write down the reaction equations for inorganic substances:
N2 + 3H2 = 2NH3 – redox reaction (ORR), ammonia was obtained;
4NH3 + 5O2 = 4NO + 6H2O – ОВР, nitrogen oxide was formed (2);
2NO + O2 = 2NO2 – ОВР, nitrogen oxide was released (4);
H2O + 2NO2 = HNO3 + HNO2 – OBP, nitric acid obtained;
2HNO3 + PbO = Pb (NO3) 2 + H2O – ion exchange, lead nitrate was formed;
2Pb (NO3) 2 = 2PbO + 4NO2 + O2 – OBP, oxygen was obtained.
The reaction products are of practical importance, for example, lead nitrate is the basis for obtaining pigments necessary for dyeing fabrics in the textile industry. These reactions show the connection of non-metals, hydrides, oxides, acids, salts.
Hiii please help me for balancing chemical equations:
potassium iodide + chlorine ------> potassium chloride + iodine
Answer:
KI + Cl2 = KCl + I2
Explanation:
hope this helps!!!
Answer:
2KI +Cl₂ → 2KCl +I₂
Explanation:
Potassium ion: K+
Iodide ion: I-
Thus, potassium iodide is KI.
Chlorine exist as a diatomic molecule thus it is written as Cl₂.
Chloride ion: Cl-
Thus, potassium chloride is KCl.
Iodine also exist as a diatomic molecule, thus it is written as I₂.
Write an unbalanced equation:
KI +Cl₂ → KCl +I₂
Now balance by ensuring the number of atoms of each element on each side is the same.
LHS
K: 1 ×2= 2
I: 1 ×2= 2
Cl₂: 2
RHS:
K: 1 ×2= 2
I: 2
Cl: 1 ×2= 2
Thus, the balanced equation is:
2KI +Cl₂ → 2KCl +I₂
Select the correct layer.
In which layer is lithification most likely to occur?
Answer:
"Subsoil" is the correct answer.
Explanation:
The method of transforming sediments become rocky solids is considered as Lithification. The floor stratum or level below the upper floors at the base of the floor is a Subsoil.Sediments comprise materials particles like sand, pebbles, skeletons kind of bones as well as muck, that were transported and produced instead in water or perhaps wind someplace.Answer: subsoil is the second layer meaning it's
Explanation:
i researched what layer subsoil is
Which of the following changes in the state of a substance results in an increase in the entropy?
Gas to solid
Gas to liquid
Liquid to solid
Solid to liquid
Answer:
the correct answer is
D. solid to liquid
pitch is produced by what??
Answer:
Pitch, in the chemical-process industries, the black or dark brown residue obtained by distilling coal tar, wood tar, fats, fatty acids, or fatty oils.
Explanation:
hopes it helps you☺
The graph shows the volume of a gaseous product formed during two trials of a reaction. A diferent concentration of reactant was used during each trial, whereas the other factors were kept constant. Trial 2 Amount of Product Trial 1 Time Which of the following statements explains which trial has a lower concentration of the reactant? O Trial 1, because the average rate of the reaction is lower. O Trial 1, because this reaction lasted for a longer duration than Trial 2. O Trial 2, because this reaction was initially fast and later slowed down. O Trial 2, because the volume of product formed per unit time was higher
Answer:
A). Trial 1, because the average rate of the reaction is lower.
Explanation:
The first sentence elaborates that 'trial 1 had a lower level of concentration of the reactant that eventually led the reaction's average rate to fall.'
A trial having a higher level of concentration of a specific reactant will cause the concentration's average rate to rise. As per the graph provided, trial 2's average reaction rate is higher which shows that its concentration is greater and more reactive. However, the opposite happens in trial 1 where the amount of reactant is lesser in the concentration that leads the concentration to possess a lower rate of reaction. Thus, option A is the correct answer.
Jonny Jonny.
Yes papa?
Eating Sugar?
What comes next?
(A) Yes Papa
(B) No Mama
(C) Yes Mama
(D) No Papa
Answer:
(B) No papa
arafgzhzhsjdjkskbdjzjsj
Answer:
(D) No Papa
Explanation:
is this even chemistry pffttt
What do the coefficients in the following balanced chemical equation mean?
2H2 + O2 → 2H2O
Answer:
number of moles of the substance
Explanation:
If we burn 1 gr of ethyl alcohol (C2H5OH) this will translate into a release of about 50 W of thermal energy of the flame that raise the temperature of the hot and cold reservoirs of a Sterling engine at 55 °C and 95 °C respectively. If at steady state the engine turns at about 240 rpm, its gears are shaped as rings of radius ~2 cm and weigh 50 gr, how efficient (in %) is the transfer of energy via flame?
Answer:
0.116%
Explanation:
efficiency of sterling engine = 1 - ( 55 + 273 )k / ( 95 + 273 ) k
= 1 - ( 328 / 368 ) = 0.10869
Determine how efficient the transfer of energy via flame is
apply this relation ; energy of steady state / energy output ---- ( 1 )
where; energy output = efficiency of sterling engine * energy
= 0.10869 * 50 = 5.4345 J/sec
energy of steady state = 1/2 * I * w^2 ------ ( 2 )
I = moment of inertia of engine = 2 * 10^-5 kgm^2
back to equation 2 :
energy of steady state = 1/2 * ( 2 * 10^-5 ) * ( 240 * 2π / 60 )^2
= 630.88 * 10^-5 J /sec
Input values into equation 1
= [ (630.88 * 10^-5 ) / 5.4345 ] * 100
= 0.116%
A sample of hydrogen gas H2 has a volume of 5.0 L and a pressure of 1.0 atm. What is the final pressure in atmospheres if the volume is decreased to 2 L with no change in temperature and amount of gas
Answer:
2.5 atm
Explanation:
P = Pressure
V = Volume
P1V1 = P2V2
1 x 5 = P2 x 2
5 = P2 x 2
Divide both sides by 2
5/2 = P2 x 2/2
P2 = 2.5
is being sporty a personality trait
Answer:
A physical trait can be identified just by looking at a person. Blonde, tall, man, short, fair skinned, injured, brown eyed, athletic, muscular, handicapped. ... For everyone character trait, there is an OPPOSITE character trait
What element has the electron configuration 1522s22p63s23p4?
Answer:
Sulphur
Explanation:
1s² 2s² 2p⁶ 3s² 3p⁴
So in total ya got 16 electrons
3===> defines the period
4+12===> defines the group
and boom, there ya got yaself an element called sulphur
Over a period of 2 minutes, 180 coulombs of charge pass through a resistor. What is the current through the resistor during this time?
Type the correct answer in the box. Use numerals instead of words.
The current through the resistor during this time is
A.
Answer:
Explanation:
Formula
The current = charge / time
The charge is in coulombs
The time has to be in seconds.
1 minute = 60 seconds
2 minutes = 120 seconds.
charge = 180 coulombs
current = 180 / 120
current = 1.5 amperes.
Use the activity series below to predict the products of each of the following reactions. Do not worry about
balancing the equations.
Li > K > Ba > Sr > Ca > Na > Mg > AI > Mn > Zn > Cr > Fe > Cd >
Co > Ni > Sn > Pb > H > Sb > Bi > Cu > Ag > Pd > Hg > Pt > Au
F2 > Cl2 > Br2 > 12
CCl4 + Br2 - ?
no reaction
CBr4 + Cl2
Answer:
i) CCl₄ and Br₂ does not react
ii) CBr₄ + Cl₂ → CCl₄ + Br₂
Explanation:
i) CCl₄ + Br₂ (no reaction)
From the given activity series, we have that chlorine gas, Cl₂, is more reactive than bromine gas, Br₂, therefore, a reaction of CCl₄ + Br₂ will not have a reaction as the propensity for the chlorine to stay combined with the carbon is higher than the ability for bromine to remain combined with or attract the carbon. Therefore, for CCl₄ + Br₂ there is no reaction
ii) CBr₄ + Cl₂
From the given activity series, we have that chlorine gas, Cl₂, is more reactive than bromine gas, Br₂, therefore, a reaction of CBr₄ + Cl₂ will give products that will have the Br in the CBr₄ replaced by the Cl₂ as follows;
CBr₄ + Cl₂ → CCl₄ + Br₂
The products of the reaction of CBr₄ and Cl₂ are therefore CBr₄ and Cl₂.
neutral radicals examples
Neutral radicals are always electropositive
some examples of neutral radicals are:-
Ca±±Mg±±Ba ±±Al±±NH4±Hope it is helpful to you
The chemical formula for carbonic acid, a compound used in carbonated drinks, is H2CO3. Assume that these symbols represent the three elements of this compound:
Which picture correctly represents carbonic acid?
A.
B.
C.
D.
Option A correctly represents the structure of carbonic acid.
What is the carbonic acid?Carbonic acid is a compound that is composed of three elements which are carbon, hydrogen and oxygen. This compound is important in the production of carbonated soft drinks that are usually sold in shops. There are three atoms of oxygen, two atoms of hydrogen and one atom of carbon in the compound.
Now, we can see in the question that red refers to atoms of oxygen, grey refers to atoms of hydrogen and ash refers to the atoms of carbon. We now want to know which diagram represents the structure of carbonic acid.
From the images, we can see that option A correctly represents the structure of carbonic acid.
Learn more about carbonic acid;https://brainly.com/question/28175742
#SPJ1
Explain the ‘oxidation half-reaction’ and the ‘reduction half-reaction’ process.
Answer:
oxidation is the loss of electrone
reduction is gain of electrons
Scoring Scheme: 3-3-2-1 Given the starting solution had a concentration of 1.25 M, how many moles of Co[H2O]6Cl2 were available in the amount of starting solution you used
Answer:
The solution has 0.00994 moles of Co[H2O]6Cl2
Explanation:
Complete question: Given the starting solution had a concentration of 1.25 M, how many moles of Co[H2O]6Cl2 were available in the amount of starting solution you used?
mL= 7.95
Step 1: Data given
Concentration of the starting solution = 1.25 M
Starting solution = Co[H2O]6Cl2
Step 2: Calculate molar mass of Co[H2O]6Cl2
Atomic mass of Co = 58.93 g/mol
Atomic mass of H = 1.01 g/mol
Atomic mass of O = 16.00 g/mol
atomic mass of Cl = 35.45 g/mol
Molar mass of Co[H2O]6Cl2 =
1*58.93 + 12*1.01 + 6*16.00 + 2*35.45 = 237.95 g/mol
Step 3: Calculate number of moles
C = n/v
⇒with C = the Concentration of the starting solution = 1.25 M
⇒with n= the number of moles = to be determined
⇒with v = the volume = 7.95 mL = 0.00795 L
n = C * V
n = 1.25 M * 0.00795 L
n = 0.00994 moles
The solution has 0.00994 moles of Co[H2O]6Cl2
What is the percent yield of a reaction?
O A. The difference between measured and calculated amounts
OB.
The amount of produd obtained
amount possible
* 100
C. The amount of product actually obtained in a reaction
D. The amount of product that is possible from a reaction
Answer:
B. The amount of produd obtained/amount possible * 100
Explanation:
In chemistry, the yield of a chemical reaction is the quantity or amount of products obtained in that chemical reaction. It is calculated by using the following formula:
Percentage yield = Actual yield/theoretical yield × 100
- The actual yield is the amount of products got from a chemical reaction
- The theoretical yield is the amount of product got from using the balanced equation (stoichiometry).
El tipo de enlace se puede determinar mediante la diferencia de electronegatividades de los átomos que lo forman. Basado en eso, si se unen un átomo de Calcio y un átomo de Bromo, el enlace será del tipo:
Answer:
Cuando se unen un átomo de calcio y un átomo de bromo, forman bromuro de calcio que se compone de Ca2 + y 2Br-. El tipo de enlace que se forma es el enlace iónico.
What is the product of the following numbers? Use a scientific calculator to
find the answer.
5.56 x 104 x 2.43 x 106
Answer:
148943.0592
Explanation:
A sealed piston contains 400 mL of air at standard ambient pressure. The piston is
compressed to an internal volume of 125 mL while keeping a constant temperature,
What is the new internal pressure (in kPa) of the air?
Answer:
324.24 kPa
Explanation:
Given that;
Initial pressure P1 = 101325 Pa
V1= 400 ml
P2 = ?
V2= 125mL
From Boyle's law;
P1V1 = P2V2
P2 = P1V1/V2
P2= 101325 × 400/125
P2= 324.24 kPa
which of the following is an example of an arrthenius acid
Answer:
The common examples of Arrhenius acid includes HCl (hydrochloric acid), H2SO4 (sulphuric acid), HNO3 (nitric acid), etc.Oct 21, 2020
Explanation:
