The force of friction acting on a sliding crate is 223 N.
How much force must be applied to main- tain a constant velocity?
Answer:
Friction Opposes Motion of an Object.
Now
To get the Net force that Moves an Object and causes acceleration....You subtract the Frictional force
Net force = Pushing Force - Frictional Force
Recall
Net Force; F=Ma
Ma = P - Fr
Now the question asked for How Much force Must be applied to Maintain a Constant velocity.
In a Constant Velocity Motion... Acceleration do not change... Its Zero
So Putting this into the formula above
M(0) = P - Fr
0=P - Fr
Fr = P.
This means
That The force needed to keep this object Moving at Constant Velocity Must be equal to its Frictional Force
Since Frictional Force; Fr =223N
The Applied Force(Pushing Force) Must be equal to 223N too.
Spending more time with her grandchildren is most likely a short-term goal
for a person of which of these ages?
A. 20 years old
B. 10 years old
C. 30 years old
D. 60 years old
Answer:60
Explanation:
calculate the voltage applied to 2.00
Answer:
Here is your answer
Explanation:
1.55 V is the answer
hope u like it
HELP, SCIENCE QUESTION I AM STUCK
6. Which of the following is NOT part of a circuit?
A. rim B. load C. power source D. conductor
A car starts from rest. if rhe final velocity becomes 50m /s after 10 second calculate the acceleration of the car.
Answer:5m/s² well I am not pretty sure but hope it's help
Explanation:
u=0m
final velocity ,v=50m/s
t=10s
(v-u)/t=(50-0)/10=50/10=5m/s²
"" damped force equation ""
Answer:
In many vibrating systems the frictional force Ff can be modeled as being proportional to the velocity v of the object: Ff = −cv, where c is called the viscous damping coefficient.
Señalar la importancia de las capacidades fisico-motiz que se desarrollan en el futbol de salon y dar un ejemplo para cada uno
La respuesta correcta para esta pregunta abierta es la siguiente.
A pesar de que no anexas opciones o incisos para responder, podemos comentar lo siguiente.
La importancia de las capacidades físico-motriz que se desarrollan en el futbol de salón son determinantes para desarrollar o maximizar las actividades propias de este deporte con objeto de rendir al máximo y aspirar al mejor de los resultados.
Estas capacidades físico-motrices son las que le permiten a un jugador realizar su máximo esfuerzo, mejorar su desempeño físico y conseguir resultados positivos.
Estamos hablando de la fuerza, la velocidad y la resistencia.
La velocidad es la aceleración que el jugador de futbol necesita para aumentar su velocidad de un punto A, a un punto B, en el menor tiempo posible.
La resistencia es la capacidad del jugador de futbol para mantener ese nivel de aceleración y desempeño, sin bajar su rendimiento. Su capacidad física debe ser resistente para ser constante en su rendimiento físico.
La fuerza es la potencia con la que desempeña los movimiento físicos dentro de la cancha.
Two tuning forks, 492 Hz and 498 Hz, are struck simultaneously. How many beats will be heard?
none
2.00 beats
4.00 beats
6.00 beats
Answer:
6 beats
If one fork beats once and another twice in the same time period
you would hear 1 beat. (Same for 2 and 3 beats).
pleaase help me i don't know this !!!
Answer:
coefficient=1.09N/m×g
coefficient=1.09N/0.413g×10m/s square
coefficient=1.09N/4.13N
coefficent=0.263
f= uK
here f is force, u is cofficient of friction , k is normal force
k = mg
f = umg
1.09 = u × 0.41 × 10
u = 1.09 ÷ 4.1
u = 0.26
What are various systems of unit?
Answer:
hlw its jess bregoli
your answer is here
SI (International System of Units) (meter-kilogram-second-ampere-kelvin-mole-candela)
FPS (foot-pound-second)
MKS (meter-kilogram-second)
CGS (centimeter-gram-second)
EMU (Electromagnetic) (centimeter-gram-second-abampere)
ESU (Electrostatic) (centimeter-gram-second-abcoulomb)
Atomic (bohr-electron mass-atomic second-electron)
MTS (meter-tonne-second)
Explanation:
hope it may help you !!
Answer:
there are 4 types of systems. They are ,
SI - accepted world wide
MKS - meter kilogram second
CGS - centimeter gram second
FPS - foot pound second
hope it helps.
A 15 cm length of wire is moving perpendicularly
through a magnetic field of strength 1.4 T at the rate
of 0.12 m/s. What is the EMF induced in the wire?
A. OV
C. 0.025 v
B. 0.018 V
D. 2.5 V
Answer: C or B
Explanation:
The EMF induced in the wire moving perpendicularly through a magnetic field is 0.025V. The correct option is C.
What is EMF?The EMF is the electro motive force which causes the current to induce in the object moving in the magnetic field.
Given is the length of wire L =15cm =0.15m, magnetic field strength B = 1.4T and velocity of wire V =0.12 m/s
EMF is related to the length of wire, magnetic field strength and velocity of wire proportionally.
ε = B x L x V
Plug the values, we get
ε = 1.4 x 0.15 x 0.12
ε = 0.025 Volts
Thus, the correct option is C.
Learn more about EMF.
https://brainly.com/question/15121836
#SPJ2
A HIGH SPEED TRAIN IS 180M LONG AND IT IS TRAVELLING AT 50M/S.HOW LONG WILL IT TAKE TO PASS A PERSON STANDING AT A LEVEL CROSSING?
B-HOW LONG WILL IT TAKE TO PASS COMPLETELY THROUGH A STATION WHOSE PLATFORMS ARE 220M IN LENGTH?
Answer:
a. Time = 3.6 seconds
b. Time = 4.4 seconds
Explanation:
Given the following data;
Distance = 180 m
Speed = 50 m/s
a. To find the time;
Speed can be defined as distance covered per unit time. Speed is a scalar quantity and as such it has magnitude but no direction.
Mathematically, speed is given by the formula;
[tex]Speed = \frac{distance}{time}[/tex]
Making time the subject of formula, we have;
[tex]Time = \frac{distance}{speed}[/tex]
Substituting into the equation, we have;
[tex]Time = \frac{180}{50}[/tex]
Time = 3.6 seconds
b. Distance = 220 meters
Speed = 50 m/s
To find the time;
[tex]Time = \frac{distance}{speed}[/tex]
Substituting into the equation, we have;
[tex]Time = \frac{220}{50}[/tex]
Time = 4.4 seconds
with respect to air the refractive index of ice is 1.31 and that of rock salt is 1.54 calculate the refractive index of rock salt with respect to ice
Answer:
1.17
Explanation:
Given that,
The refractive index of ice wrt air = 1.31
The refractive index of rock salt wrt air = 1.54
We need to find the refractive index of rock salt with respect to ice.
We know that,
refractive index = (speed of light in air or vaccum)/( speed of light in that medium)
So,
The speed of light in ice = c/(1.31)
The speed of light in rock salt = c/(1.54)
So, the refractive index of rock salt with respect to ice is :
[tex]\mu=\dfrac{1.54}{1.31}\\\\=1.17[/tex]
So, the required refractive index of rock salt wrt ice is 1.17.
Select the correct answer.
Which quantity is a vector quantity?
ОА. .
acceleration
OB.
mass
OC.
speed
O D.
volume
Reset
Next
Answer:
acceleration is the vector quantity because it depends on particular direction and has magnitude
Which has greater kinetic energy, a car traveling at 40 mph or a half-as-massive car traveling at 80 mph?
a
-The 40 mph car
-The 80 mph car
-Both have the same kinetic energy
-Neither has kinetic energy
Answer:
The 80 mph car
Because the formula says 1/2 mass but for the velocity it is squared
A room has a rectangular shape of 4000 mom by 3600mm according to the architecture plan It is supposed to be fitted with tiles which are square in shape and size of 12 cm. How many tiles are required to cover the entire floor
Explanation:
First find the area of the entire floor:
Area of a rectangle= length × width
( 4000mm× 3600mm)
14400000mm²
Area of one square tile??= side ×side
12cm×12cm
144cm²
Convert cm to mm
1cm²=100mm²
144cm²=144cm²/1cm²×100mm²
=14,400mm²
Number of tiles required to cover the entire floor= 14400000mm²/14400mm²
=1000
a student drops a ball off the top of building and records that the ball takes 3.32s to reach the ground (g=9.8 m/s^2). what is the ball's speed just before hitting the ground?
Answer:
Explanation:
Use the one-dimensional equation for motion
v = v₀ + at and filling in,
v = 0 + (-9.8)(3.32) so
v = -33 m/s (negative because it is going downwards and upwards is positive).
The circuit diagram below shows the locations of four switches. Which
switch configuration creates a short circuit?
fo
W
WT
Answer:
C option
Explanation:
Hope this helps... pls vote as brainliest
in a series circuit, how does the voltage supplied by the battery compare to the voltages on each load?
Answer:
In a series circuit, how does the voltage supplied by the battery compare to the voltage on each load? The voltage of the battery is equal to the voltage of each load added together. ... The voltage across the two resistors must both have the same voltage of the battery.
Explanation:
mark me as BRAINLIEST
follow me
carry on learning
Answer:
The voltage of the battery is equal to the voltage of each load added together. The voltage across the two resistors must both have the same voltage of the battery.
>3
A ball is dropped from the top of a building. It initially
moves at 40 m/s. After 0.5 seconds, it moves at 3.8
m/s.
What force is responsible for the slowing of the ball?
air resistance
gravity
normal
tension
Answer:
Explanation:
I'm assuming you missed the decimal point in the initial velocity and that it should be 4.0 m/s. If after a half of a second it is moving a tiny bit slower, it would be because of air resistance. You can only neglect air resistance if the problems you are doing tell you neglect it.
Answer:
Air resistance
Explanation:
I got it correct on the quiz :)
Match the reactants with the products. zinc sulfate + copper aluminum chloride + copper copper oxide copper + water copper sulfate + oxygen
Answer:
The Reactants Products
Copper sulfate + zinc → Zinc sulfate + copper
aluminum + copper chloride → Aluminum chloride + Copper
Copper + Oxygen → Copper oxide
Explanation:
The Reactants Products
Copper sulfate + zinc Zinc sulfate + copper
aluminum + copper chloride Aluminum chloride + Copper
Copper + Oxygen Copper oxide
First reaction can be described as a single replacement reaction
Second reaction is also a single replacement reaction just like the first reaction
The third is a synthesis reaction ( i.e. reaction in which elements combine to form single compound )
I need help with question 6
Answer:
0.16 h
Explanation:
Speed: 25km per hour
Speed=distance/time
25=4/t
t=4/25
t=0.16 hour
t=9.6 minuites
Brainliest please~~
A car travelling along a straight road has kinetic energy of 180 kJ. The brakes are applied, and it is brought to rest over a distance of 60 m. What is the average force of the car breaks?
A. 3 N
B. 3000 N
C. 10,800 N
Answer:
Given,
w= 180J
s=60m
W=F×s
180=F×60
180/60=F
F= 3 N
Ball X has a mass of 8kg and is moving toward ball Y (which is sitting still) at 2m/s. After they collide, ball X is
sitting still. How fast is ball Y moving after the collision if it has a mass of 4kg?
Answer:
v = 4 m/s
Explanation:
Given :
Ball X :
Mass, m1 = 8kg ;
Initial Velocity, u1 = 2 m/s
Final velocity, v1 = 0
Ball Y:
Mass, m2 = 4kg ;
Initial Velocity, u2 = 0 m/s
Final velocity, v2 = v
(m1u1 + m2u2) = (m2v2 + m1v1)
(8*2 + 4*0) = (4*v + 4*0)
16 + 0 = 4v + 0
16 = 4v
v = 16 / 4
v = 4 m/s
Answer:
Explanation:
This is the Law of Momentum Conservation which for us looks like this:
[tex][m_xv_x+m_yv_y]_b=[m_xv_x+m_yv_y]_a[/tex] and that should look familiar to you if this is what you are doing in physics. Filling in our particular info:
[(8.0 × 2.0)+ (4.0 × 0.0)] = [(8.0 × 0.0) + (4.0v)] and
16 + 0 = 0 + 4.0v and
16 = 4.0v so
v = 4.0 in the direction of ball X
b) A stone floor feels very cold to bare feet in winter, but a carpet in
the same room feels comfortably warm. Why is this?
Answer:
A stone floor feels very cold to bare feet in winter, but a carpet in the same room feels comfortably warm.This is because both the floor and the carpet have the same temperature as both are exposed to the same atmosphere. But the former conducts away the heat from the feet better than the carpet as the latter is a non-conductor. So the feet losing more heat, the floor appears cooler to the feet
Explanation:
Hope it may help you!!
Both actually have same temperature. Our feet are warm. Floor is conductor of heat while carpet is not. When we walk on floor, then floor takes away or conducts the heat from our feet, so we feel cold. While carpet doesn't do that, so we feel warm.
The drone can fly for 25 minutes before the battery needs recharging.
The power output of the battery is 65.0 W
Calculate the maximum energy stored by the battery.
Answer:
105.6 KJ
Answer
3.7/5
4
hope this will help you friend.
A constant unbalanced force is applied to an object for a period of time. What will happen to the objects acceleration?
a. It will accelerate in the direction of the net force.
b. It will accelerate opposite the direction net force.
c. There is no acceleration.
d. Not enough information to answer
Answer:
A
Explanation:
The moving object will accelerate as long as a net force is applied. If a net force is not applied, the object will continue to move at a constant speed along the same path in curved spacetime (due to gravity). If the net force continues the velocity of the object will continue to increase until nearly reaching the limit (speed of light).
when is the acceleration of body is positive negative and zero?
Answer:
【 In vector form , if angle between velocity vector and acceleration vector is less than 90° and greater than 0° then it is positive acceleration and if it is less than 180° and greater than 90° then it is negative acceleration. If there is no acceleration vector then it is called zero acceleration. 】
can someone please help me I will mark you as brilliant.
The current in a resistor is 5 A and the voltage between its terminals is 40 V. Calculate the resistance.
An iron wire has a resistance of 24 Ω. If the voltage across its ends is 12 V, calculate the current in the wire.
Answer:
1=8 ohms 2=0.5 Amps
Explanation:
At the local grocery store, you push a 14.5-kg shopping cart. You stop for a moment to add a bag of dog food to your cart. With a force of 12.0 N you now accelerate the cart from rest through a distance of 2.29 m in 3.00 s. What was the mass of the dog food?
Answer:
The mass of the dog food added is 9.03 kg
Explanation:
Given;
mass of the shopping cart, m₁ = 14.5 kg
let the mass of the bag added = m₂
the force applied, F = 12 N
initial velocity of the cart-bag system, u = 0
distance traveled by the system, d = 2.29 m
time of motion of the system, t = 3.0 s
The acceleration of the system is calculated as;
[tex]d = ut + \frac{1}{2} at^2\\\\2.29 = 0 + (\frac{1}{2} \times 3^2)a\\\\2.29 = 4.5 a\\\\a = \frac{2.29}{4.5} \\\\a = 0.51 \ m/s^2[/tex]
The total mass of the system (M) is calculated as follows;
F = Ma
M = F/a
M = (12)/(0.51)
M = 23.53 kg
The mass of the dog food added is calculated as;
m₂ = M - m₁
m₂ = 23.53 kg - 14.5 kg
m₂ = 9.03 kg
