Answer:
F = 3 N + 2 N = 5 N
Explanation:
Resultant force F = 3 N + 2 N = 5 N to the right. The resultant force is 5 N to the right. Two forces that act in opposite directions produce a resultant force that is smaller than either individual force. To find the resultant force subtract the magnitude of the smaller force from the magnitude of the larger force.
In the construction of a large reactor pressure vessel, a new steel alloy with a plane strain fracture toughness of 55 MPa-m1/2 and a Y value of 1.0. An in-service stress level of 200 MPa has been calculated. What is the length of a surface crack (in mm) that will lead to fracture
Answer:
[tex]l=24mm[/tex]
Explanation:
From the question we are told that:
Plane strain fracture toughness of [tex]T=55 MPa-m1/2[/tex]
Y value [tex]Y=1.0[/tex]
Stress level of[tex]\sigma =200 MPa[/tex]
Generally the equation for length of a surface crack is mathematically given by
[tex]l=\frac{1}{\pi}(\frac{T}{Y*\sigma})^2[/tex]
[tex]l=\frac{1}{3.142}(\frac{55}{1*200})^2[/tex]
[tex]l=0.024m[/tex]
Therefore
in mm
[tex]l=24mm[/tex]
A force measuring instrument comes with a certificate of calibration that identifies two instrument errors and assigns each an uncertainty at 95% confidence over its range. Provide an estimate of the instrument design-stage uncertainty.
Resolution: 0.25 N
Range: 0 to 100 N
Linearity error: within 0.20 N over range
Hysteresis error: within 0.30 N over range
Answer:
[tex]U=\pm 0.382N[/tex]
Explanation:
From the question we are told that:
Resolution: 0.25 N
Range: 0 to 100 N
Linearity error: within 0.20 N over range
Hysteresis error: within 0.30 N over range
Generally the equation for Stage Uncertainty is mathematically given by
[tex]U=\sqrt{u_0^2+u_T^2}[/tex]
Where
[tex]u_0=Zero\ order\ uncertainty[/tex]
[tex]u_0=\pm 0.5*0.25[/tex]
[tex]u_0=\pm=0.125[/tex]
And
u_T=Total instrumental Uncertainty
[tex]u_T=\sqrt{l_e^2+h_e^2}[/tex]
Where
l_e=Error of linearity
h_e=Error due to hysteresis
Hence
[tex]u_T=\sqrt{0.20^2+0.30^2}[/tex]
[tex]u_T=\pm 0.36[/tex]
Therefore
[tex]U=\sqrt{(0.125)^2+0.36^2}[/tex]
[tex]U=\pm 0.382N[/tex]
Transients (surges) on a line can cause spikes or surges of energy that can damage delicate electronic components. A SPD device contains one or more ________________ than bypass and absorb the energy of the transient.
Answer:
I think ( MOV Metal oxide varistors )
Transients (surges) on a line can cause spikes or surges of energy that can damage delicate electronic components. A SPD device contains one or more MOV Metal oxide varistors than bypass and absorb the energy of the transient.
Doubling the diameter of a solid, cylindrical wire doubles its strength in tension.
True
False
Answer:
True ❤️
-Solid by solid can make Cylindrical wire doubles Strengths in tension
A investor will invest in mutual fundwith a probability of 0.6, will invest in government fundwith a probability of 0.3, and will invest in both fundswith a probability of 0.15. Find the probability that the investor will invest in either mutual fundor government fund.
Answer:
0.75
Explanation:
From this question above we have the following information
A = probability of investment in mutual fund= 0.6
B = probability of investment in government fund = 0.3
C = probability of investing in both the mutual fund and the government= 0.15
Where to find the probability of this investor investing in either of these two
= Prob(a) + prob(b) - prob(c)
= 0.6 + 0.3 - 0.15
= 0.9 - 0.15
= 0.75
Block A hangs by a cord from spring balance D and is submerged in a liquid C contained in beaker B. The mass of the beaker is 1.20 kg; the mass of the liquid is 1.85 kg. Balance D reads 3.10 kg and balance E reads 7.50 kg. The volume of block A is 4.15 × 10−3 m3.
a) What is the density of the liquid?
b) What will the balance D read if block A is pulled up out of the liquid?
c) What will the balance E read if block A is pulled up out of the liquid?
Answer:
a) [tex]m_e= 3.05 Kg[/tex]
b) [tex]\rho=1072.3kg/m^3[/tex]
c) [tex]m_e= 3.05 Kg[/tex]
Explanation:
From the question we are told that:
Beaker Mass [tex]m_b=1.20[/tex]
Liquid Mass [tex]m_l=1.85[/tex]
Balance D:
Mass [tex]m_d=3.10[/tex]
Balance E:
Mass [tex]m_e=7.50[/tex]
Volume [tex]v=4.15*10^{-3}m^3[/tex]
a)
Generally the equation for Liquid's density is mathematically given by
[tex]m_e=m_b+m_l+(\rho*v)[/tex]
[tex]\rho=\frac{7.50-(1.2+1.85)}{4.15*10^{-3}}[/tex]
[tex]\rho=1072.3kg/m^3[/tex]
b)
Generally the equation for D's Reading at A pulled is mathematically given by
m_d = mass of block - mass of liquid displaced
[tex]m_d=m- (\rho *v )[/tex]
[tex]m=3.10+ (1072.30 *4.15*10^{-3}m^3 )[/tex]
[tex]m=18.10kg[/tex]
c)
Generally the equation for E's Reading at A pulled is mathematically given by
[tex]m_e=m_b+m_l[/tex]
[tex]m_e = 1.20 + 1.85[/tex]
[tex]m_e= 3.05 Kg[/tex]
If an elevator repairer observes that cables begin to fray after 15 years, what process might he or she use to create a maintenance schedule for their replacement? fallacious reasoning reductive reasoning inductive reasoning deductive reasoning
Answer:
inductive reasoning
Explanation:
Inductive reasoning is one of the type of reasoning method in which generalized consequences are derived from limited observations. By observing few data, general conclusions are drawn. The conclusions drawn are false in inductive reasoning. In the given situation, the conclusion drawn by the elevator repairer has been drawn by inductive reasoning. His observation of some cables led him to draw the conclusion about all the cables. The result of the reasoning is false.
EnQueue(X): Thêm phần tử X vào Queue
DeQueue() : Lấy 1 phần tử ra khỏi Queue
Hãy cho biết phần tử ở đầu của Queue có giá trị bằng bao nhiêu sau khi thực hiện lần lượt các phép toán sau:
EnQueue(1); EnQueue(2); DeQueue(); EnQueue(3);
EnQueue(4); DeQueue(); DeQueue();
Please help me:
Use the Node analysis to find the power of all resistors
A pinion and gear pair is used to transmit a power of 5000 W. The teeth numbers of pinion
and gear are 20 and 50. The module is 5 mm, the pressure angle is 20o
and the face width is 45 mm. The
rotational speed of pinion is 300 rev/min. Both the pinion and the gear material are Nitralloy 135 Grade2 with a hardness of 277 Brinell. The quality standard number Qv is 5 and installation is open gearing
quality. Find the AGMA bending and contact stresses and the corresponding factors of safety for a
pinion life of 109
cycles and a reliability of 0.98
Answer:
mark me as a brainleast
Explanation:
209781
Apart from the type of emergency, what factors affect the decision on weather to evacuate or shelter in place?
Answer:
. 1. Type of building
2. Location of emergency
3. Extent of emergency
Explanation:
1. The kind of building in which people find themselves could be a factor that can be used to make this decision. a lot of buildings can be easily affected by disasters such as explosions or tornadoes the extent of the effect is dependent on how the building is constructed. in some situations it is better to shelter in, while in others it is best to evacuate.
2. Another factor to be considered is the location or area where this is happening it is good to consider this so that people can be safely moved given that help can be easily accessed or if best to stay in.
3. The last is the extent of what is happening. The risk involved is one way of making the choice to evacuate or to stay.
The factors that affect the decision on whether to evacuate or shelter in place include:
Type of building.Location of emergency.Extent of emergencyIt should be noted that the building where an individual lives play a vital role during emergencies. Buildings that have poor foundations can easily be affected during emergencies.
Another factor that should be considered is the location where the emergency is taking place. Lastly, the extent of the emergency can determine if the person should stay or not.
Learn more about emergencies on:
https://brainly.com/question/3237467
An ideal gas within a piston-cylinder assembly undergoes a Carnot refrigeration cycle. The isothermal compression occurs at 325 K from 2 bar to 4 bar. The isothermal expansion occurs at 250 K. Determine:
a. the coefficient of performance
b. the heat transfer to the gas during the isothermal expansion, in kj per kmol of gas
c. the magintude of the net work input, in kj per kmol of gas.
Answer:
a) [tex]\mu=3.3[/tex]
b) [tex]Q=1440.7KJ/Kmol[/tex]
c) [tex]W=1872.9KJ/Kmol[/tex]
Explanation:
From the question we are told that:
Initial Temperature [tex]T_1=325k[/tex]
initial Pressure [tex]P_1=2 bar[/tex]
Final Pressure [tex]P_2=4 bar[/tex]
iso-thermal expansion [tex]T_2=250k[/tex]
a)
Generally the equation for Coefficient of performance is mathematically given by
[tex]\mu=\frac{T_2}{T_1-T_2}[/tex]
[tex]\mu=\frac{250}{325-250}[/tex]
[tex]\mu=3.3[/tex]
b)
Generally the equation for Heat Expansion is mathematically given by
[tex]Q=RT_2 In(\frac{P_2}{P_1})[/tex]
Where
R=Gas constant
[tex]R=8.314462618[/tex]
Therefore
[tex]Q=8.314462618*250 In(\frac{4}{2})[/tex]
[tex]Q=1440.7KJ/Kmol[/tex]
c)
Generally the equation for work input is mathematically given by
[tex]W=RT_1 In(\frac{P_2}{P_1})[/tex]
[tex]W=8.314462618*250 In(\frac{4}{2})[/tex]
[tex]W=1872.9KJ/Kmol[/tex]
The coefficient of performance is 3.33, the heat transfer in the isothermal expansion is 1440.71kJ/K.mol and the work input is calculated as 1872.92kJ/K.mol
Given Data:
T1 = 325KP1 = 2 barP2 = 4 barT2 = 250KIsothermal expansion occurs at 250K.
a) The coefficient of performanceThis is calculated as
COP =[tex]\frac{T_2}{T_1-T_2}=\frac{250}{325-250} =3.33[/tex]
b) Heat Transfer in isothermal expansion[tex]Q = RT_2In(\frac{p_2}{p_1})[/tex]
Therefore; In isothermal process du = 0
R = 8.314 AkJ/K.mol
Q = 8.314 * 250 In(4/2)
Q = 1440.71kJ/K.mol
c) Work InputW[tex]_i_n[/tex]=[tex]RT_1In(\frac{p_2}{p_1})\\W_i_n=8.314*325In(4/2)\\W_i_n=1872.92kJ/K.mol[/tex]
The work input is 1872.92kJ/K.mol
Learn more on Carnot cycle here:
https://brainly.com/question/14983940
https://brainly.com/question/13170743
Which of the following would make a column more likely to buckle?
Increase its ultimate compressive strength
Increase its length
Increase its Young’s modulus
Increase its cross-sectional area
Increase its area moment of inertia
True or false: Increasing a material’s ultimate compressive strength makes it less likely to crush under its own weight (assuming all other things equal).
True
False
True or false: The area moment of inertia of an object only depends on its shape, not its size.
True
False
Answer:
1) B: Increase its length
2) True
3) True
Explanation:
1) Columns are compressive members and are subjected to primarily compressive stresses.
Now, there is what we call slender Ness ratio in columns which is basically used to check the ability of a column to resist buckling.
The formula is;
Slenderness ratio = Effective length of column/radius of gyration
Thus, the longer the column the more the Slenderness ratio and the more likely it is to buckle.
Thus, increasing the length is what makes columns likely buckle.
2) Compressive strength is the ability of a material to withstand loads that may reduce size or make the material crush under load.
Now, increasing the compressive strength simply means more ability to withstand loads that may lead to crushing under load.
Ultimate compressive strength is the maximum amount of compressive stress that a material can take before it crushes under load. Thus, increasing the ultimate compressive strength means it is less likely to crush under its own weight.
3) There are different factors that affect moment of inertia and they are;
- the mass of the body
- axis of rotation of the body
- shape and size of the body.
However, for area moment of inertia, what is most relevant to us is the shape of the body in question since we are dealing with area and not how big it is.
A rod that was originally 100-cm-long experiences a strain of 82%. What is the new length of the rod?
122 cm
182 cm
82 cm
22 cm
108.2 cm
Answer: (b)
Explanation:
Given
Original length of the rod is [tex]L=100\ cm[/tex]
Strain experienced is [tex]\epsilon=82\%=0.82[/tex]
Strain is the ratio of the change in length to the original length
[tex]\Rightarrow \epsilon =\dfrac{\Delta L}{L}\\\\\Rightarrow 0.82=\dfrac{\Delta L}{100}\\\\\Rightarrow \Delta L=82\ cm[/tex]
Therefore, new length is given by (Considering the load is tensile in nature)
[tex]\Rightarrow L'=\Delta L+L\\\Rightarrow L'=82+100=182\ cm[/tex]
Thus, option (b) is correct.
Explain ROLAP, and list the reasons you would recommend its use in the relational database environment.
Answer:
ROLAP is a branch of OLAP that is used to contain Relational database ( RDB ). which is a very fast database ( quick process of queries )
Very fast to access and also fast in processing queries provides multidimensional view of data / supports multidimensional database schema with RDBMssupports large databasesExplanation:
ROLAP ( Relational On-line Analytical processing ) is a branch of OLAP that is used to contain Relational database ( RDB ).
Advantages of ROLAP ( reasons for the use of ROLAP )
Very fast to access ( fast in processing queries )provides multidimensional view of data / supports multidimensional database schema with RDBMssupports large databasesA piece of coaxial cable has 75ohms Characteristics impedance and a nominal capacitance of 69pF/m. what is its inductance per meter ? If the diameter of the inner conductor is 0.584mm, and the dielectric constant of the insulation is 2.23, what is the outer diameter of the conductor ?
Answer:
A) L = 0.388 μm
B) D = 3.78 mm
Explanation:
We are given;
Characteristics impedance; Z_o = 75 ohms
Nominal capacitance; C = 69pF/m = 69 × 10^(-12) F/m
dielectric constant; k = 2.23
Inner diameter of conductor; d = 0.584 mm
A) Now formula for Characteristics impedance is given as;
Z_o = √(L/C)
Where L is the inductance per metre.
Making L the subject, we have;
L = (Z_o)²C
L = 75² × 69 × 10^(-12)
L = 0.388 × 10^(-6) m
L = 0.388 μm
B) To get the outer diameter, we will use the formula;
Z_o = (138/√k) log(D/d)
Where;
D is outer diameter.
Thus, Plugging in the relevant values;
75 = (138/√2.23) × log (D/0.584)
log (D/0.584) = 0.81158611538
(D/0.584) = 10^(0.81158611538)
D/0.584 = 6.48016576435
D = 6.48016576435 × 0.584
D = 3.78 mm
Which of the following is not a part sympathetic activation during the fight or flight response?
Answer:
Digestion functions become more active
Explanation:
I just took the text!
Two engineers are to solve an actual heat transfer problem in a manufacturing facility. Engineer A makes the necessary simplifying assumptions and solves the problem analytically, while engineer B solves it numerically using a powerful software package. Engineer A claims he solved the problem exactly and, thus, his results are better, while engineer B claims that he used a more realistic model and, thus, his results are better. Will the experiments prove engineer B right
Answer:
Engineer A results will be more accurate
Explanation:
Analytical method is better than numerical method. Engineer A has used analytical method and therefore his results will be more accurate because he used simplified method. Engineer B has used software to solve the problem related to heat transfer his results will be approximate.
Elliptic curve cryptography is considered as the latest and probably the one with a future. Having seen RSA in earlier modules, in which ways do YOU think elliptic cryptography is more advanced than RSA. You may read other material or get this information from the internet to answer this question. But make sure to provide necessary references when you do cite others.
Answer:
The answer is below.
Explanation:
Some of the ways, how I think elliptic cryptography is more advanced than RSA are the following:
1. ECC - Elliptic Curve Cryptography uses smaller keys for the same level of security, particularly at greater levels of security.
2. ECC can work well and at a faster rate on a small-capacity device compared to RSA
3. It uses offer speedier SSL handshakes that enhance security
4. It offers fast signatures
5. It allows signatures to be computed in two stages, which enables lower latency than inverse throughput.
6. Relatively quick encryption and decryption
Calculate the minimum area moment of inertia for a rectangular cross-section with side lengths 6 cm and 4 cm.
Answer:
Minimum area of rectangle = 24 cm²
Explanation:
Given:
Length of rectangle = 6 cm
Width of rectangle = 4 cm
Find:
Minimum area of rectangle
Computation:
Area of rectangle = Length of rectangle x Width of rectangle
Minimum area of rectangle = Length of rectangle x Width of rectangle
Minimum area of rectangle = 6 x 4
Minimum area of rectangle = 24 cm²
A network has three independent file servers, each with 90 percent reliability. The probability that the network will be functioning correctly (at least one server is working) at a given time is:
Answer:
The correct answer is "99.9%".
Explanation:
According to the information given in the question,
[tex]P(1 \ fail) = 0.1[/tex]
The probability of all fail will be:
[tex]P(all \ fail) = (0.1)^3[/tex]
[tex]=0.001[/tex]
hence,
[tex]P(not \ all \ fail)= 1-P(all \ fail)[/tex]
[tex]=0.999[/tex]
[tex]=99.9[/tex] (%)
Thus the above is the right answer.
Wave flow of an incompressible fluid into a solid surface follows a sinusoidal pattern. Flow is two-dimensional with the x-axis normal to the surface and y axis along the wall. The x component of the flow follows the pattern
u = Ax sin (2πt/T)
Determine the y-component of flow (v) and the convective and local components of the acceleration vector.
Answer:
sorry , for my point
Explanation:
Air enters a diffuser operating at steady state at 540°R, 15 lbf/in.2, with a velocity of 600 ft/s, and exits with a velocity of 60 ft/s. The ratio of the exit area to the inlet area is 8. Assume that The air is the ideal gas model for the air and ignoring heat transfer, determine
Answer: Hello the question is incomplete below is the missing part
Question: determine the temperature, in °R, at the exit
answer:
T2= 569.62°R
Explanation:
T1 = 540°R
V2 = 600 ft/s
V1 = 60 ft/s
h1 = 129.0613 ( value gotten from Ideal gas property-air table )
first step : calculate the value of h2 using the equation below
assuming no work is done ( potential energy is ignored )
h2 = [ h1 + ( V2^2 - V1^2 ) / 2 ] * 1 / 32.2 * 1 / 778
∴ h2 = 136.17 Btu/Ibm
From Table A-17
we will apply interpolation
attached below is the remaining part of the solution
A rod that was originally 100-cm-long experiences a strain of 82%. What is the new length of the rod?
122 cm
182 cm
82 cm
22 cm
108.2 cm
Answer:
The new length of the rod is 182 cm.
Explanation:
Given that a rod that was originally 100-cm-long experiences a strain of 82%, to determine what is the new length of the rod, the following calculation must be performed:
100 x 1.82 = X
182 = X
Therefore, the new length of the rod is 182 cm.
Given : x² + 200x = 166400 The current park is a square, and the addition will increase the width by 200 meters to give the expanded park a total area of 166,400 square meters To Find : the side length of the current square park. Solution: x² + 200x = 166400 => x(x + 200) = 166400 166400 = 320 * 520 => (320)(320 + 200) = 166400 => x = 320 side length of the current square park. = 320 m Learn More: Which expression is a possible leading term for the polynomial ... brainly.In/question/13233517
Answer:
320 m
Explanation:
To find the side length of the current park, x, we solve the quadratic equation for the area of the park
x² + 200x = 166400
x² + 200x - 166400 = 0
We multiply -166400 by x² to get -166400x². We now find the factors of 166400x² that will add up to 200x. These factors are -320x and 520x
So, we re-write the expression as
x² + 200x - 166400 = 0
x² + 520x - 320x - 166400 = 0
We write out the factors of the expression,
x² + 520x - 320x - 320 × 520 = 0
Factorizing the expression, we have
x(x + 520) - 320(x + 520) = 0
(x + 520)(x - 320) = 0
x + 520 = 0 or x - 320 = 0
x = -520 or x = 320
Since x is not negative, we take the positive answer.
So, x = 320 m
In heavy traffic areas you should wave pedestrians across the street if there is no crosswalk
In heavy traffic areas, you should wave pedestrians across the street if there is no crosswalk: False.
What is a crosswalk?A crosswalk can be defined as the marked or specially paved part of a road that is characterized by heavy traffic, so as to enable pedestrians have right of way to cross the street because drivers are required by traffic law to stop for them.
However, a driver or other road users in heavy traffic areas shouldn't wave pedestrians across the street if there is no crosswalk
Read more on traffic laws here: https://brainly.com/question/22768531
a video inspection snake is use
Answer:
very good thx
Explanation:
Compute the minimum length of vertical curve that will provide 220 m stopping sight distance for a design speed of 110 km/h at the intersection of a -3.50% grade and a +2.70% grade.
i have made notes and saved it as a pdf u can take it to answer question and make ur concept good
The minimum length of vertical curve that will provide 220 m stopping sight distance is; 458.8 m
We are given;
Stopping sight distance; S = 220 m
Design Speed; V = 110 km/h
Intersection grade 1; G1 = +2.7
Intersection Grade 2; G2 = -3.5
From the AASHTO Table attached, we can trace the value of the radius of vertical curvature for the given stopping sight distance and design speed.From the table, at S = 220 m and V = 110 km/h, we can see that;
Radius of vertical curvature; K = 74
Now, the difference in grade given is;A = G1 - G2
A = 2.7 - (-3.5)
A = 2.7 + 3.5
A = 6.2
Formula for the minimum length of vertical curve is;L = KA
Thus;
L = 74 × 6.2
L = 458.8 m
Read more about stopping sight distance at; https://brainly.com/question/2087168
Unfiltered full wave rectifier with a 120 V 60 Hz input produces an output with a peak of 15V. When a capacitor-input filter and a 1k ohm load are connected the DC output voltage is 14V. What is... The value of the capacitor? The value of the peak to peak ripple voltage?
Answer:
[tex]V_{pp}=2V[/tex]
Explanation:
Source Voltage [tex]V= 120V[/tex]
Frequency [tex]f=60Hz[/tex]
Peak output voltage [tex]Vp=15V[/tex]
Peak Output Voltage with filter [tex]V_p'=14V[/tex]
Generally the equation for Peak to peak voltage is mathematically given by
[tex]V_p'=V_p-\frac{V_{pp}}{2}[/tex]
Therefore
[tex]V_{pp}=2(V_p-v_p')[/tex]
[tex]V_{pp}=2(15-14)[/tex]
[tex]V_{pp}=2V[/tex]
Why water parameters of Buriganga river vary between wet and dry seasons?
Explain.
