what is BEFORE and AFTER when you put the baking soda in vinegar?​

The amount of potassium chloride that will dissolve in 50 grams of water at 50°C depends on the solubility of the salt at that temperature. The solubility of potassium chloride in water at 50°C is approximately 42 grams per 100 grams of water. Therefore, about 21 grams of potassium chloride will dissolve in 50 grams of water at 50°C.

As the molar mass calculated is 24.90 g/mol, hence the gas is most likely to be NO.

The ratio between mass and the amount of substance of any sample is called molar mass.

To determine whether the gas is NO, NO2, or N2O5, we need to calculate the molar mass of the gas and compare it to the molar masses of these three possible gases.

n = PV/RT

Given, P = 760.0 mmHg, V = 250.0 mL = 0.2500 L, T = 17.00°C + 273.15 = 290.15 K, and R = 0.08206 L atm/mol K.

So, n = (760.0 mmHg)(0.2500 L)/(0.08206 L atm/mol K)(290.15 K) = 0.01003 mol

M = m/n

Given m = 0.2500 g.

M = 0.2500 g/0.01003 mol = 24.90 g/mol

Comparing this molar mass to the molar masses of NO (30.01 g/mol), NO2 (46.01 g/mol), and N2O5 (108.01 g/mol), we see that the gas is most likely NO.

To know more about molar mass, refer

https://brainly.com/question/837939

#SPJ1

Note: The question given on the portal is incomplete. Here is the complete question.

Question: A 250.0-mL flask contains 0.2500 g of a volatile oxide of nitrogen. The pressure in the flask is 760.0 mmHg at 17.00°C. Is the gas NO, NO2, or N2O5?

Nitration of toluene takes place in four steps which include formation of nitronium ion, formation of electrophile, deprotonation, and elimination of  HNO₃.

The mechanism for the nitration of toluene showing explicitly why ortho and para products are favored over meta is as follows:

Step 1: Formation of the Nitronium Ion

NO₂⁺ is formed by nitric acid's reaction with sulfuric acid.

2HNO₃ + H₂SO₄ → 2 NO₂⁺ + 2HSO₄⁻ + H₃O⁺

The following is the formation of a nitronium ion:

Step 2: Formation of the electrophile

A nitronium ion is created, which is the electrophile. Because of the strong electron-releasing effect of the methyl group, the nitronium ion is drawn to the ring.

Due to the stability of the resulting carbocation, ortho and para products are favored over meta. In this, the bond on the methyl carbon is broken and the electrophile is added to it:

Step 3: Deprotonation: After the nitration reaction, an intermediate is formed in which a proton has been extracted from the methyl group. The formation of this intermediate indicates that the electrophile has been added to the ring's ortho or para positions.

Step 4: Elimination of HNO₃: An acid base reaction occurs to complete the nitration process, yielding nitrotoluene, HNO₃, and sulfuric acid. Here the intermediate is used to illustrate that the reaction has occurred with the ortho product. This reaction may also result in a para product in a similar manner.

Learn more about Nitration here:

https://brainly.com/question/26927899

#SPJ11

Actually, when atomic radius grows, electronegativity often decreases.

The capacity of an atom to draw electrons into a chemical connection is known as electronegativity. The separation between the nucleus and the farthest electrons grows with increasing atomic radius. As a result, the nucleus's attraction to the electrons is reduced, making it more challenging for the atom to draw electrons to itself. The electronegativity values of bigger atoms are therefore often lower than those of smaller ones. Despite this general tendency, there are certain outliers since electronegativity also depends on other elements including nuclear charge and electron configuration. For instance, the rising nuclear charge in halogens causes the electronegativity to rise as the atomic radius falls.

learn more about electronegativity here:

https://brainly.com/question/17762711

#SPJ4

The potassium tert-butoxide is final product of the reaction is (CH3)3COH.

Why potassium tert-butoxide is (CH3)3COH?

The product for the given reaction is (CH3)3COH.

Reaction: (CH3)3CBr + KOtBu →(CH3)3COH + KBr

Potassium tert-butoxide (KOtBu) is a strong base that can deprotonate hydrogen from (CH3)3COH to form (CH3)3CO-.On the other hand,

(CH3)3CBr is a tertiary halide that can undergo an E2 reaction.

E2 is the abbreviation for bimolecular elimination reactions,

which involve the abstraction of a proton from the adjacent carbon and the removal of the halide anion.

The hydrogen that is abstracted by KOtBu can only come from the carbon that is adjacent to the bromine in (CH3)3CBr, according to Saytzeff's rule, because this is the carbon with the least number of hydrogens.

As a result, an alkene intermediate will be formed.

The KBr salt will be the by-product.

The alkene intermediate, however, is not present in the end product because it is a reactive molecule and quickly reacts with any available hydrogen.

The hydrogen is provided by the KOtBu base.

As a result, the final product of the reaction is (CH3)3COH.

Learn more about potassium tert-butoxide

brainly.com/question/29484874

#SPJ11

Answer:

(A).Liquid water has a specific heat of 4.184J/g.k

(B)Volume = 39,420 LSo, kilograms= 44.7 kg

Explanation:

(a) The specific heat at constant volume of nitrogen (N2) gas is 20.8 J/K.mol. Compare it with the specific heat of liquid water.Liquid water has a specific heat of 4.184 J/g.K

(b) For the same amount of heat, we would be able to warm 44.7 kg of 20.0 °C air to 30.0 °C. Air has a molar mass of 28.97 g/mol. We can use the ideal gas law to determine the volume of 44.7 kg of air at 20.0 °C and 1.00 atm pressure.

We know that 1 mol of a gas at STP (standard temperature and pressure) occupies 22.4 L. Since air is 100% N2, its molar mass is 28.0 g/mol. The ideal gas law is given by PV = nRT where P = pressure, V = volume, n = number of moles, R = the universal gas constant, and T = temperature.

Substituting values, we have:

PV = nRTV = nRT/PAt

20.0 °C and 1.00 atm, T = 293 K and P = 1.00 atm.

Therefore, we have:

n = mass/molar mass = 44.7 kg / (28.97 g/mol) = 1543.8 mol

R = 0.082 L.atm/K.mol

Substituting these values into the equation, we have:

V = (1543.8 mol)(0.082 L.atm/K.mol)(293 K) / (1.00 atm)

V = 39,420 LSo, 44.7 kg of 20.0 °C air occupies a volume of 39,420 L at 20.0 °C and 1.00 atm pressure.

To know more about ideal gas law refer here: https://brainly.com/question/30458409#
#SPJ11

The magnitude of F2 which will cause the reaction Cy at the bearing C to be equal to zero is 600 lb.

Let's assume the direction of F2 is x-axis and direction of Cy is y-axis. Apply the force balance equation along x-axis:

F2 = F1 + F3F3 = F2 - F1

As we know, the force along the y-axis is zero. So, there is no force balance equation along y-axis. Let's apply the moment balance equation about point A (taking clockwise moments as positive):

F1 × 4 + F2 × 6 = F3 × 2F1 × 4 + F2 × 6 = (F2 - F1) × 2

Now substitute F1 = 300 lb in the above equation.

300 × 4 + F2 × 6 = (F2 - 300) × 2300 × 4 + 6F2 = 2F2 - 600F2 = 600 lb

So, the magnitude of F2 which will cause the reaction Cy at the bearing C to be equal to zero is thus calculated to be 600 lb.

More on force: https://brainly.com/question/18596795

#SPJ11

For the molecular formula of aspartame, the artificial sweetener marketed as NutraSweet, is [tex]C_{14}H_{18}N_2O_5[/tex],

a. the molar mass of aspartame is 294.30 g/mol.

b. there are 3.40 x [tex]10^{-6}[/tex] moles of aspartame in 1.00 mg of aspartame.

c. there are 2.05 x [tex]10^{18}[/tex] molecules of aspartame in 1.00 mg of aspartame.

d. the total number of hydrogen atoms in 1.00 mg of aspartame is 34 hydrogen atoms.

a. The molar mass of aspartame can be calculated by adding up the atomic masses of all its atoms:

Molar mass of aspartame = (14 x 12.01 g/mol) + (18 x 1.01 g/mol) + (2 x 14.01 g/mol) + (5 x 16.00 g/mol) = 294.30 g/mol

Therefore, the molar mass of aspartame is 294.30 g/mol.

b. The number of moles of aspartame present in 1.00 mg of aspartame can be calculated using the formula:

moles = mass/molar mass

moles = 1.00 mg / 294.30 g/mol = 3.40 x 10^-6 mol

Therefore, there are 3.40 x 10^-6 moles of aspartame in 1.00 mg of aspartame.

c. The number of molecules of aspartame present in 1.00 mg of aspartame can be calculated using Avogadro's number:

number of molecules = moles x Avogadro's number

number of molecules = 3.40 x [tex]10^{-6}[/tex] mol x 6.02 x [tex]10^{23}[/tex] molecules/mol = 2.05 x [tex]10^{18}[/tex] molecules

Therefore, there are 2.05 x 10^18 molecules of aspartame in 1.00 mg of aspartame.

d. The number of hydrogen atoms present in 1.00 mg of aspartame can be calculated as follows:

There are 14 carbon atoms in 1.00 mg of aspartame, and each carbon atom is bonded to two hydrogen atoms. Therefore, there are 28 hydrogen atoms bonded to carbon atoms.

There are 2 nitrogen atoms in 1.00 mg of aspartame, and each nitrogen atom is bonded to three hydrogen atoms. Therefore, there are 6 hydrogen atoms bonded to nitrogen atoms.

There are 5 oxygen atoms in 1.00 mg of aspartame, and each oxygen atom is not bonded to any hydrogen atoms.

Therefore, the total number of hydrogen atoms in 1.00 mg of aspartame is 28 + 6 + 0 = 34 hydrogen atoms.

Learn more about the molecular formula of aspartame at

https://brainly.com/question/26876807

#SPJ4

After 12 minutes, the amount of 2N-71 remaining would be 25 grams. This is because the half-life of 2N-71 is 2.4 minutes, meaning that after 2.4 minutes, half of the initial amount (50 grams) will remain. After 12 minutes, half of the remaining 25 grams will have decayed, leaving 25 grams.

The initial amount of 2n-71 is 50 g, and the half-life of 2n-71 is 2.4 minutes. We need to determine how many grams of 2n-71 would be left after 12 minutes. During radioactive decay, the amount of a radioactive substance decreases exponentially over time. The formula for determining the amount remaining of a radioactive substance after time t is:A = A₀(1/2)^(t/h)Where, A₀ = the initial amount of the substance,A = the amount of the substance after time t,h = the half-life of the substance, and t = time elapsedPlugging the given values in the formula, we get:A = 50(1/2)^(12/2.4)A = 50(1/2)^5A = 50(1/32)A = 1.5625Therefore, the amount of 2n-71 left after 12 minutes is 1.5625 g.

For more details follow this link: https://brainly.com/question/31108721

#SPJ11

When writing the volume dispensed by a 5 ml volumetric pipet, it should be written as 5.00 mL.

A volumetric pipet is a laboratory instrument utilized to dispense very accurate and precise volumes of liquid. It is commonly used in analytical chemistry to make up solutions or to dilute stock solutions. Volumetric pipettes, also known as transfer pipettes or bulb pipettes, are single-volume liquid measuring instruments. They are meant to deliver a precise volume of liquid at a fixed temperature when the tip is slightly below the liquid surface.

It is important to write the volume with two decimal places to indicate the precision of the pipette.

Volumetric pipettes are utilized to prepare and dilute solutions. They are made of glass, with a round or conical end. They are intended to provide a precise volume of liquid, such as a certain number of milliliters or milligrams of a substance. Because of its accuracy, a volumetric pipet is used to create a standard solution.

For more such questions on volumetric pipet, click on:

https://brainly.com/question/28945018

#SPJ11

The molecule which would have the highest boiling point is 2-methylhexane. Thus, the correct option will be D.

The boiling point is the temperature at which the vapor pressure of a liquid is equal to the external pressure. The boiling point of a liquid is a measure of its vapor pressure. The higher the boiling point, the higher the vapor pressure of the liquid, and the more heat is required to vaporize it.

The boiling point of a substance is affected by the strength and types of intermolecular forces. The stronger the intermolecular forces, the higher the boiling point. 2-methylhexane has highest boiling point because it has the highest number of carbons and branches, which contribute to its strong intermolecular forces that lead to a higher boiling point.

Therefore, the correct option is D.

Learn more about Boiling point here:

https://brainly.com/question/25777663

#SPJ11

To determine if a data point can be ignored when calculating the average in General Chemistry, Appendix D of the lab manual recommends using the Q-test at 95% confidence. The Q-test is a statistical test that is used to determine if a data point is an outlier, or if it falls outside the expected range of values for the data set.

To use the Q-test, one must calculate the Q-value for each data point and compare it to the critical Q-value at the desired level of confidence. If the calculated Q-value is greater than the critical Q-value, then the data point is considered an outlier and can be excluded from the calculation of the average.

Regarding the second question, the spectator ions in the reaction between aqueous perchloric acid and aqueous barium hydroxide are H+ and ClO4-. These ions do not participate in the chemical reaction, but are present in the solution due to the dissociation of the reactants. The actual chemical reaction is the formation of insoluble barium perchlorate (Ba(ClO4)2) and water (H2O) through the combination of barium hydroxide (Ba(OH)2) and perchloric acid (HClO4), which are the only ions involved in the reaction.

To learn more about barium hydroxide refer to

brainly.com/question/30888146

#SPJ4

A calorie is the commonly used unit of chemical energy. it is also the unit of energy used to measure the energy content of food.

Calorie (or kilocalorie) is a unit of measurement used to measure the energy content of food. It is the amount of energy required to raise the temperature of one kilogram of water by one degree Celsius.

One calorie is equal to the amount of energy required to raise the temperature of one gram of water by one degree Celsius.

Energy is a fundamental property of matter that can take many forms, such as electrical, thermal, chemical, nuclear, and mechanical energy.

Learn more about Calorie here:

https://brainly.com/question/1178789

#SPJ1

The reagent(s) for the given transformation is "A B C D E F G H I", which is t-BuOK, OsO4, NMO, O3, DMS, H2, Pt, H2, Lindlar's cat., xs HBr, BH3.THF, H202, NaOH, MeONa, Br2, hv.

Transformation is the process of changing something into a different form or state. It can involve altering the physical characteristics, behaviors, attitudes, or perceptions of an entity. Transformation is a process that occurs in a variety of contexts including business, education, technology, and personal development.

A) t-BuOK - For the given transformation, the initial step is to add an alkoxide, here t-BuOK, to the starting material.
B) OsO4, NMO - After the addition of the alkoxide, the resulting intermediate has to be oxidized by OsO4 and NMO reagents.
C) 1) O3; 2) DMS - The intermediate then has to be ozonolyzed using ozone and dimethyl sulfide (DMS).
D) H2, Pt - The ozonolysis will result in a mixture of aldehyde and ketone. The aldehyde has to be hydrogenated using H2 and Pt.
E) H2, Lindlar's cat. - The ketone has to be hydrogenated using H2 and Lindlar's catalyst.
F) xs HBr - The product of the hydrogenation has to be converted to a tertiary alcohol by an elimination reaction with HBr.
G) 1) BH3.THF; 2) H202, NaOH - The tertiary alcohol has to be oxidized to a tertiary ketone using BH3.THF, H202 and NaOH.
H) MeONa - The tertiary ketone has to be methylated using MeONa.
I) Br2, hv - The product of the methylation has to be brominated using Br2 and heat.
Therefore, the reagent(s) for the given transformation is "A B C D E F G H I", which is t-BuOK, OsO4, NMO, O3, DMS, H2, Pt, H2, Lindlar's cat., xs HBr, BH3.THF, H202, NaOH, MeONa, Br2, hv.

To learn more about transformation
https://brainly.com/question/382594
#SPJ1

The phenomenon in which electrons that are closer to the nucleus slightly repel those that are farther out is known as Shielding.

Electrons in an atom are negatively charged particles, and they are attracted to the positively charged nucleus. However, the outer electrons of an atom are also repelled by the inner electrons that are closer to the nucleus. This repulsion is due to the negative charges of the electrons, and it partially cancels out the attraction of the nucleus for the outer electrons.

Shielding is the phenomenon in which electrons that are closer to the nucleus slightly repel those that are farther out. This makes it possible for electrons in higher energy levels to be farther from the nucleus, so they are less strongly attracted and easier to remove.

Learn more about Shielding here: https://brainly.com/question/27985711

#SPJ11

The reaction in the gas mixture will proceed non-spontaneously in the forward direction when the standard free energy change (∆G°) is positive or zero.

In chemical reactions, the term spontaneity refers to whether the reaction proceeds on its own or requires an input of energy to occur. When ∆G° is negative, a reaction is said to be spontaneous in the forward direction, meaning it occurs naturally without any external input of energy. When ∆G° is positive or zero, on the other hand, the reaction proceeds nonspontaneously in the forward direction.

In other words, the reaction requires energy input to proceed. The free energy change (∆G) of a reaction is related to its standard free energy change (∆G°) through the equation:

∆G = ∆G° + RT ln(Q)

where, R is the gas constant, T is the temperature in Kelvin, and Q is the reaction quotient.

If Q = 1, the reaction is at equilibrium and ∆G = ∆G°. If Q < 1, the reaction proceeds spontaneously in the forward direction (∆G < 0), and if Q > 1, the reaction proceeds spontaneously in the reverse direction (∆G > 0).

Learn more about Spontaneous reaction here:

https://brainly.com/question/13790391

#SPJ11

As sodium acetate is added to the solution, the sodium ions (Na+) will replace the hydrogen ions (H+) in the equation. This causes a shift in the equilibrium as the number of hydrogen ions (H+) decreases, while the number of acetate ions (CH3COO-) increases.

Sodium acetate is an ionic compound composed of Na⁺ and CH₃COO⁻ ions.

It dissociates in water to create these ions, which are then available to affect the dissociation of acetic acid.

The equilibrium of acetic acid dissociation is influenced by the addition of sodium acetate.

Acid dissociation equilibria are influenced by salt addition (usually sodium salts), particularly when the acid is weak.

This is due to the fact that the anion of the salt reacts with hydrogen ions from the acid's dissociation.

This decreases the concentration of hydrogen ions in the solution, causing the reaction to shift towards more dissociation.

Learn more about acid dissociation constant here:

https://brainly.com/question/3006391

#SPJ11

The correct option is dissolving ammonium nitrate in water to cool the water.

Among the given options, the example of an exothermic reaction is dissolving ammonium nitrate in water to cool the water.

Exothermic reactions are chemical reactions that release heat energy into the surroundings. As a result, the products have less energy than the reactants. Dissolving ammonium nitrate in water to cool the water is a good example of an exothermic reaction because it releases heat energy and cools down the surrounding water.

When ammonium nitrate dissolves in water, it releases heat, causing the temperature of the water to decrease. The reaction is exothermic because it releases heat to the surroundings. Dissolving sugar in water and melting ice are examples of endothermic reactions because they absorb heat energy from the surroundings.

Therefore, the correct answer is the option of dissolving ammonium nitrate in water to cool the water.

To learn more about exothermic reactions refer - https://brainly.com/question/10373907

#SPJ11

The wavelength (in nm) of the photon absorbed for a transition of an electron that results in the least energetic spectral line in ultraviolet series of the H atom is 121.6 nm.

This is derived from the Rydberg formula, which relates the energy levels of an electron in an atom to the wavelength of light emitted or absorbed in the process of an electron transitioning from one level to another. Using the equation E_n = -13.6 eV/n^2, we can find the energy level of the n_initial=1 electron state to be -13.6 eV.

Subtracting this value from the energy level of the n=2 state, which is -3.4 eV, we obtain the energy difference between the two states as 10.2 eV. Using E = hf = hc/λ, where h is Planck's constant (6.626 x 10^-34 Js), c is the speed of light (2.998 x 10^8 m/s), and f is the frequency of the absorbed photon, we can calculate the wavelength of the photon as 121.6 nm.

Know more about Rydberg formula here:

https://brainly.com/question/13185515

#SPJ11

The electron transport chain (ETC) is an essential part of cellular respiration, which is a series of molecules that transfer electrons from one molecule to another used by cells to convert nutrients into energy.

This starts with the oxidation of molecules such as glucose, which releases electrons that are then transferred to a series of electron carriers in the ETC. The electron carriers are molecules that hold the electrons and can transfer them to other molecules which is known as redox reactions. As the electrons move through the ETC, they release energy which is used to form a proton gradient that is then used to drive the synthesis of ATP, the energy currency of the cell. The ETC is an essential part of cellular respiration as it is the process responsible for generating the energy necessary for cells to function.

To learn more about electron click here https://brainly.com/question/28977387

#SPJ4

The solution with the highest boiling point at standard pressure is the one with the highest concentration of solutes, which increases the boiling point of the solution. In this instance, the answer is 0.10 M MgCl2(aq).

What is boiling point and standard pressure?

Boiling point: The boiling point of a solution is the temperature at which the vapour pressure of the solution equals the external pressure, allowing the solution to boil.

Standard pressure: One atmosphere of pressure is defined as the standard pressure.

A solution has the highest boiling point at standard pressure (1 atm) when it has the greatest concentration of solutes (molarity).

Which solution has the highest boiling point at standard pressure?

MgCl2 will have the greatest boiling point at a normal pressure since it has the most solute concentration.

The boiling point of a liquid is raised when solutes are added to it because the vapour pressure of the solution is lowered, thus more energy is required to break the intermolecular forces between the solvent and solute particles.

The boiling point of the solution rises as more solute is dissolved in the solvent, and the solvent-solute intermolecular forces become stronger, thus increasing the boiling point.

As a result, the 0.10 M MgCl2(aq) solution has the greatest boiling point among the options given.

for more information about boiling point at standard pressure refer here:

https://brainly.com/question/238983?

#SPJ11

The volume of H₂ gas produced from 1.30 g of Mg in excess HCl is 0.0019 L.

The balanced equation for the reaction of magnesium metal with HCl is:

Mg + 2HCl → MgCl₂ + H₂

The molar mass of Mg is 24.31 g/mol.

The mass of Mg that reacted = 1.30 g

The moles of Mg that reacted = 1.30 g ÷ 24.31 g/mol = 0.0535 mol

According to the balanced equation, 1 mol of Mg reacts with 1 mol of H₂

Therefore, 0.0535 mol of Mg will produce 0.0535 mol of H₂.

Since, the volume of gas produced is proportional to the number of moles of the gas, we can use the ideal gas equation to find the volume of H₂

PV = nRT

Where, P = 720 torr = 720/760 atm (1 atm = 760 torr)

T = 34 + 273 = 307 K

R = 0.0821 L·atm/mol·K

V = n × 0.0821 L·atm/mol·K × 307 K/ 720 torr = 0.0535 mol/ 720 torr × 25.2047 L/molK =0.0019 L

At 720 torr and 34 °C, 0.0535 mol of hydrogen occupies a volume of 0.0019 L.

To learn more about "volume of hydrogen", visit: https://brainly.com/question/30176170

#SPJ11

The green metal carbonate is decomposed according to the given equation: MCO₃(s) → MO(s) + CO₂(g)

What is molar mass of MCO₃?

The number of moles of CO₂(g) produced can be used to determine the number of moles of the green metal carbonate (MCO₃) that decomposed.0.222 g of CO₂ (g) represents 1 mol of CO₂ (g), since its molar mass is 44 g/mol.

Therefore,1 mol of MCO₃ will produce 1 mol of CO₂ (g) in the reaction. So, 0.222 g of CO₂ (g) corresponds to 1 mol of MCO₃.

Hence, the number of moles of MCO₃ is:

moles of MCO₃= mass/Molar

mass= 0.598 g/Molar mass of MCO₃

The molar mass of MCO₃ can be calculated using the following:

mass percent of MCO₃ = [(mass of M)/(molar mass of M)] × 100%molar mass of MCO₃ = mass of MCO₃/moles of MCO₃

By substituting the value of moles of MCO₃ and the mass of MCO₃ into the equation above, the molar mass of MCO₃ can be calculated.

molar mass of MCO₃= (mass of MCO₃) / (moles of MCO₃)

Finally, to determine the molar mass of metal M, subtract the molar mass of CO3 from the molar mass of MCO₃.

MCO₃ = 12.011 + 3(15.999) + M(55.845)

= 181.76 + 55.845MM

= 55.845 - 60.01MM

= -4.165

The molar mass of the metal M is 4.165 g/mol.

To summarize, the metal M is sodium (Na) and its molar mass is 4.165 g/mol.

To know more about molar mass:

brainly.com/question/23058220

#SPJ11

The complete ionic equation for the reaction that occurs when aqueous solutions of lithium sulfide and copper (II) nitrate are mixed is as follows: 2 Li+(aq) + S2-(aq) + Cu2+(aq) + 2 NO3-(aq) → CuS(s) + 2 Li+(aq) + 2 NO3-(aq)

It is important to write the complete ionic equation when aqueous solutions of lithium sulfide and copper (II) nitrate are mixed. The reaction of lithium sulfide with copper (II) nitrate is a double displacement reaction. Lithium sulfide reacts with copper (II) nitrate to form copper sulfide and lithium nitrate.

The balanced chemical equation for the reaction is given as follows:Li2S(aq) + Cu(NO3)2(aq) → CuS(s) + 2 LiNO3(aq)The complete ionic equation can be written by representing all the ions in the aqueous solutions as dissociated ions.

Thus, the complete ionic equation for the reaction that occurs when aqueous solutions of lithium sulfide and copper (II) nitrate are mixed is as follows:2 Li+(aq) + S2-(aq) + Cu2+(aq) + 2 NO3-(aq) → CuS(s) + 2 Li+(aq) + 2 NO3-(aq.

)In the above equation, the lithium and nitrate ions do not take part in the reaction and are present in the same form in the reactant and product side. Hence, they are called spectator ions.

To know more about ionic equation, refer here:

https://brainly.com/question/15138610#

#SPJ11

The free moving charged particles in a Carbon electrode made of electrode are electrons.

An electrode is a substance that conducts electricity, which means it allows electric charges to travel through it. During electrolysis, an electrode is used to provide an electric current for the reduction and oxidation reactions that take place.

A carbon electrode is a type of electrode that is made of carbon. Carbon electrodes are commonly used in batteries and fuel cells because they are lightweight and can easily conduct electricity.

Electrons are free moving charged particles in a carbon electrode made of electrode. Electrons are negatively charged subatomic particles that orbit the nucleus of an atom. They are found in the outer shells of atoms and can move freely from one atom to another when they are excited by an electric current.

When an electric current is passed through a carbon electrode, the electrons in the outer shells of the carbon atoms are excited and become free moving charged particles. This allows the carbon electrode to conduct electricity and to participate in reduction and oxidation reactions during electrolysis.

For more such questions on electrode, click on:

https://brainly.com/question/28302450

#SPJ11

The best material for insulation in this case would be Styrofoam. Styrofoam is lightweight, strong, and an excellent thermal insulator. It is composed of tiny bubbles of air that are suspended in a matrix of plastic. The air trapped inside the bubbles acts as a thermal barrier, keeping heat out or in, depending on the application.

Its lightweight nature makes it easier to manipulate, while its strength gives it the durability needed to keep a drink hot or cold. Its insulation properties also make it the perfect material for the student's insulated drink cup.

Styrofoam can be cut and shaped easily, making it a great material for use in drink cups. The material is also easy to clean and resistant to water and other liquids, which makes it ideal for frequent use. Additionally, Styrofoam is both affordable and widely available, making it an ideal choice for the student's project.

Know more about thermal insulator here:

https://brainly.com/question/23134662

#SPJ11

AgCl is more likely to dissolve in water when ammonia (NH3) is present. This is due to the fact that ammonia and AgCl may combine to create the water-soluble complex ion, Ag(NH3)2+.

At 25°C, the solubility of AgCl in water is 0.0020 g of AgCl per litre of H2OS.

AgCl dissolves in NH3 at a rate of 14.00 g per kilogramme of NH3 when the temperature is 25°C. Due to the production of the soluble stable complex [AgNH32]+, AgCl is more soluble in NH3. Since oxygen is more electronegative than nitrogen, ammonia is less polar than water.

AgCl is well known to be insoluble in water whereas NaCl and KCl are soluble in the pedagogical literature: implementations of Elementary studies of both qualitative and quantitative analysis make this distinction.

To know more about ammonia visit:-

https://brainly.com/question/20524322

#SPJ1

The chemical formula [tex]Al_2SiO_5[/tex] can form the three minerals, andalusite, kyanite, and sillimanite under different combinations of temperature and pressure conditions. Option D is correct.

Learn more about the chemical formula: https://brainly.com/question/11574373

#SPJ11

The experimental molar mass of CO2 collected in a laboratory experiment is 44.0 g/mol.

When carrying out laboratory experiments, carbon dioxide gas is collected to determine the molar mass of the compound. When a 500 mL flask was filled with the evolved CO2 at 294 K and 1.01 atm, 1.008 grams of CO2 was collected. It is required to determine the experimental molar mass of CO2. To solve the problem, we will make use of the ideal gas law formula:

P.V = n.R.T Where,P = 1.01 atmV = 500 mL = 0.500 Ln = number of moles of CO2R = 0.0821 L.atm.K-1.mol-1T = 294 K Substituting the values in the formula, we get;1.01 atm × 0.500 L = n × 0.0821 L.atm.K-1.mol-1 × 294 K1.01 × 0.500 = n × 24.79n = (1.01 × 0.500) / 24.79n = 0.02039 moles of CO2. We know that the mass of CO2 that was collected is 1.008 grams.Therefore, the molar mass of CO2 = mass / number of moles = 1.008 g / 0.02039 mol = 49.38 g/mol

But, we know that CO2 has a molar mass of 44.01 g/mol. Hence, the value of 49.38 g/mol is not the experimental molar mass of CO2 and so, we have to calculate the experimental molar mass of CO2 as follows:Experimental molar mass of CO2 = mass / number of moles = 1.008 g / 0.02039 mol = 49.38 g/mol. Actual molar mass of CO2 = 44.01 g/mol.

Experimental error = | experimental value - actual value | / actual value × 100%.Substituting the values in the formula, we get;

Experimental error = | 49.38 - 44.01 | / 44.01 × 100%

Experimental error = 12.2% ≈ 12%.

Therefore, the experimental molar mass of CO2 is 44.0 g/mol (Option b).

More on molar mass: https://brainly.com/question/18879890

#SPJ11

When benzoquinone is treated with excess butadiene, the products obtained are 2,5-dimethylcyclohexadiene-1,4-dione and cyclohexene.

Benzoquinone is also known as 1,4-benzoquinone or cyclohexa-2,5-diene-1,4-dione, is a colorless organic compound. The presence of two carbonyl groups in its structure provides it its characteristic quinone chemistry.

Butadiene, also known as 1,3-butadiene, is a conjugated diene. The reaction between benzoquinone and butadiene is called a Diels-Alder reaction.

The Diels-Alder reaction is a conjugate addition reaction that joins a diene and a dienophile to create a new six-membered ring. The most important characteristic of the Diels-Alder reaction is its stereospecificity. This reaction occurs between a cyclic diene and an alkene or alkyne dienophile.

The products obtained when benzoquinone is treated with excess butadiene are:2,5-dimethylcyclohexadiene-1,4-dioneCyclohexeneThe reaction proceeds with the dienophile (benzoquinone) being attacked by the diene (butadiene) in the Diels-Alder reaction to produce a cyclic adduct. The product is 2,5-dimethylcyclohexadiene-1,4-dione. Cyclohexene is formed as a byproduct of the reaction.

Learn more about Benzoquinone here:

https://brainly.com/question/15014857

#SPJ11